IN2128HDa
PZ339-A000-00
Regulatory models: IN2128HDa
Download from Www.Somanuals.com. All Manuals Search And Download.
Agency Approvals
cMETus
Other specific Country Approvals may apply. Please see product certification label.
This document applies to regulatory model IN2128HDa
Input ratings: 100-240Vac, 3.2A, 50-60Hz
InFocus reserves the right to alter product offerings and specifications at any time without
notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Table of Contents
25
Download from Www.Somanuals.com. All Manuals Search And Download.
3
•
•
•
Refer all service to qualified service personnel. Servicing your own projector
can be dangerous to you and will void the warranty.
Important Operating Considerations for Safety
•
•
•
Refer to this guide for proper startup and shutdown procedures.
Follow all warnings and cautions in this manual and on the projector.
Only use replacement parts specified by InFocus. Unauthorized substitutions
may result in fire, electrical shock, or injury, and may void the warranty
Place the projector in a horizontal position no greater than 15 degrees off
axis.
Only genuine InFocus lamps are tested for use in this projector. Use of non
InFocus lamps may cause electrical shock and fire, and may void the projector
warranty.
•
•
Locate the projector at least 4' (1.2m) away from any heating or cooling
vents.
•
•
Hg – Lamp contains mercury. Manage in accordance with local
Do not block ventilation openings. Locate the projector in a well-ventilated
area without obstructions to intake or exhaust vents. Do not place the
projector on a tablecloth or other soft covering that may block the vents.
The projector uses a high-pressure mercury glass lamp. The lamp may fail
prematurely, or it may rupture with a popping sound if jolted, scratched, or
handled while hot. The risk of lamp failure or rupture also increases as the
lamp age increases; please replace the lamp when you see the “Replace Lamp”
message.
•
•
Do not place the projector in direct sunlight, humid, greasy or dusty places or
in places where the projector may come into contact with smoke or steam.
Do not touch or block the projector lens with any objects as this can damage
the projector lens. Scratches, gouges and other lens damage are not covered
by the product warranty.
•
In the unlikely event of a lamp rupture, particles may exit through the
projector vents. Please keep people, food, and drinks at least 3’ (1m) away
from all projector vents. For ceiling applications, keep people, food and drinks
out of the "keep out" area under and around the projector, as indicated by
the illustration.
•
•
•
•
Do not look directly into the lens while the projector is being used.
Do not drop the projector.
Do not spill liquid on the projector. Spilled liquid may damage the projector.
Use the power cord provided. Connect the power cord to a receptacle with
a protective safety (earth) ground terminal. A surge-protected power strip is
recommended.
•
•
•
•
Do not overload wall outlets.
When disconnecting the power cord, hold the plug, not the cord.
Wash hands after handling the cables supplied with this product.
m
5
8
.
/ 1
’
/ 2
.
4
m
’
5
Follow these instructions to help ensure image quality and lamp life over the life of
the projector. Failure to follow these instructions may affect the warranty. For
complete details of the warranty, see the Warranty/Safety booklet.
The projector remote control uses batteries. Make sure the batteries’
polarity (+/-) is aligned correctly. Dispose of used batteries in accordance
with local disposal laws.
•
•
Use an InFocus approved ceiling mount kit for proper fitting, ventilation and
installation. The warranty does not cover any damage caused by use of non-
approved ceiling mount kits or by installing in an improper location.
When the projector is ceiling mounted, wear protective eyewear to prevent
eye injury before opening lamp door.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Introduction
keypad
Your new digital projector is simple to connect, easy to use, and straightforward to maintain.
It is a versatile projector that is flexible enough for business presentations and home video
viewing too. IN2128HDa has native 1080p 1920 x 1080 resolution. It is compatible with a
wide variety of computers and video devices.
lamp cover
zoom
Product specifications
To read the latest specifications on your multimedia projector, be sure to visit our website at
www.infocus.com, as specifications are subject to change.
remote control
receiver (IR)
security bar
lens
Accessories
The standard accessories that came with your projector are listed in the included Quick
Start Guide. Optional accessories can be found on our website at www.infocus.com/
support or at your retailer or dealer.
focus
Online registration
warranty and receive product updates, announcements, and registration incentives.
connector
panel
power cord
connector
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Connector panel
The projector provides both computer and video connection options, including:
S-video
computer
monitor out
•
•
•
•
•
VGA computer (2)
Composite video
HDMI
RS 232
USB type B
USB type A
HDMI
audio in/out
S-video
USB B connector (for projector firmware upgrades, mouse control, Screen
Save Preventer, and optional LiteBoard™wand)
•
•
USB Mini B (for Display over USB, loading internal memory and EZ media
firmware upgrade)
USB A (View photos, movies, documents and listen to audio from USB drive,
display wirelessly with optional WiFi adapter, and upgrade EZ Media
firmware)
•
•
•
•
•
•
LAN (RJ45 for network control and video over LAN)
Liteboard radio for use with the optional LiteBoard™wand and dongle.
Monitor out, for VGA pass through to an external monitor.
Audio inputs for video and computer.
Liteboard
radio
composite
video
LAN
security lock
USB mini B
Audio output to external speakers.
RS-232 serial control. Command control codes are on our support website at
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Positioning the projector
To determine where to position the projector, consider the size and shape of your
screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Here are some general guidelines:
Table 1: IN2128HDa (1080p) Screen size
Throw Ratio = 1.5 to 1.8
Size of the
Projected Image
Width
Distance to screen
Diagonal Screen
Size (inches/m)
•
Position the projector on a flat surface at a right angle to the screen.
IN2128HDa must be at least 37.5” (1.0m) from the projection screen.
Minimum distance
(inches/m)
Maximum distance
(inches/m)
(inches/m)
40”/1.0m
60”/1.5m
80”/2.0m
100”/2.5m
150”/3.8m
35”/0.9m
52”/1.3m
70”/1.8m
87”/2.2m
131”/3.3m
52.3”/1.3m
78.4”/2.0m
104.6”/2.7m
130.7”/3.3m
196.1”/5.0m
62.7”/1.6m
94.1”/2.4m
125.5”/3.2m
156.9”/4.0m
235.4”/6.0m
•
If you are installing the projector on the ceiling, we strongly recommend using
InFocus approved ceiling mounts for proper fitting, ventilation and installation.
Refer to the installation guide that comes with the InFocus Ceiling Mount Kit
(p/n PRJ-MNT-UNIV) for more information. The warranty does not cover
any damage caused by use of non-approved ceiling mount kits or by installing
in an improper location. To turn the image upside down, see “Ceiling mount”
•
Position the projector the desired distance from the screen. The distance
from the lens of the projector to the screen and the video format determine
the size of the projected image.
Model
Minimum Distance to Screen
37.5"/1.0m
Offset
Offset for 60in. Image
5"/12.7cm
IN2128HDa
17%+-5%
60 inches
high image
Projection angle
bottom of image 5
inches above center
of lens
lens center
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Connecting a computer source
connect VGA cable
connect USB cable
connect HDMI
VGA connection
Connect one end of the provided computer cable to the Computer 1/Computer 2
connector on the projector and the other to the VGA connector on your computer. If you
are using a desktop computer, you will need to disconnect the monitor cable from the
computer’s video port first.
USB Mini-B connection
Connect one end of the USB cable to the USB Mini-B connector on the projector and the
MOLEX
MOLEX
USB Type-B connection
Connect one end to the USB cable to the USB Type-B connector on the projector and the
operation.
HDMI connection
HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI provides an
interface between sources, such as set-top boxes, DVD players, and receivers and your
projector. Plug an HDMI cable into the video-out connector on the video device and into the
HDMI connector on the projector.
connect power
Connecting power
Connect the black power cord to the Power connector on the rear of the projector and to
your electrical outlet. If the Power Saving Mode feature is off, the Power LED on the Status
Indicator Panel (page 11) blinks blue. If the Power Saving Mode feature is on, the Power LED
Always use the power cord that shipped with the projector.
Optional computer connections
connect audio cable
To get sound from the projector, connect an audio cable (optional cable, not included) to
your computer and to the Audio 1/Audio 2 connector on the projector. You may also need
an adapter.
If you are using a desktop computer and want to see the image on your computer screen as
well as on the projection screen, connect to the desktop’s computer cable to Computer 1
and the desktop’s monitor cable to the Monitor Out connector on the projector.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Displaying an image
Press the Power button.
press Power button
The Power LED lights blue, and the fans start to run. When the lamp comes on, the start up
screen displays. It can take up to a minute for the image to achieve full brightness. Note:
When the feature, AC Power On, is enabled, the projector automatically turns on when
power is connected. This allows control of ceiling mounted projectors with a wall power
switch.
No start up screen? Get help on page 13.
Turn on your computer or video device.
turn on computer or
video device
The image should appear on the projection screen. If it doesn’t, press the Source button on
the projector’s keypad or remote.
If you are using a VGA cable to connect your computer to the projector:
If using a laptop, make sure its external video port is active.
activate laptop’s external port
Many laptops do not automatically turn on their external video port when a projector is
connected. Usually a key combination like FN + F8 or CRT/LCD key turns the external
display on and off. Locate a function key labeled CRT/LCD or a function key with a monitor
symbol. Press FN and the labeled function key simultaneously.
monitor key or
LCD/CRT key
Refer to your laptop's documentation for more information about your laptop's
key combination.
FN key
No laptop image? Try pressing the Auto Image button on the remote. Get help on
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Adjusting the image
If necessary, adjust the height of the projector by rotating the elevator foot to extend the
foot.
adjust height
elevator
foot
If necessary, rotate the leveling foot located at the rear of the projector.
Avoid placing your hands near the hot exhaust vent at the front of the projector.
adjust distance
Position the projector the desired distance from the screen at a 90 degree angle to the
screen.
Adjust the zoom or focus.
adjust zoom and focus
If the image is not square, first make sure that the projector is perpendicular to the screen. If
the image is larger or smaller on the top or bottom edge of the screen, press the top
Keystone button
Keystone button
to reduce the upper part of the image, and press the bottom
to reduce the lower part.
If the left or right side of the screen is larger or smaller the other, you can turn the projector
to the left or to the right a few degrees to square the image.
adjust keystone
adjustments.
MDL: IN2128HDa
FW: X.XX
( Basic Menu )
Aspect Ratio
Auto Image
Brightness
Contrast
adjust Basic Menu
◄
Execute
50
50
Auto
►
Auto Keystone
Keystone
Off
0
Presets
Presentation
Sharpness
Volume
Ceiling Mount
16
16
Off
Advanced Menu
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
S-video connection
Plug the S-video cable’s connector into the video-out connector on the video device. Plug
the other connector into the S-Video connector on the projector.
Connecting a video device
You can connect video devices such as VCRs, DVD players, camcorders, digital cameras,
video game consoles, HDTV receivers, and TV tuners to the projector. You can connect the
audio directly to the projector to get sound from the built-in speaker, or you can bypass the
projector’s audio system and connect the audio directly from your source to a stereo or
home theater system.
Audio
For audio, connect a 3.5mm stereo cable to the Audio 1/Audio 2 connector on the projector
and to your source. If your source uses RCA audio connectors, a Y-cable or adapter may be
used. (Note: A separate audio connection is not required for HDMI source inputs.)
You can connect the projector to most video devices that can output video. You cannot
directly connect the coaxial cable that enters your house from a cable or satellite company,
the signal must pass through a tuner first. Examples of tuners are digital cable boxes, VCRs,
digital video recorders, and satellite TV boxes. Basically, any device that can change channels
is considered a tuner.
Before connecting your projector, you should decide which aspect ratio you want to use.
The projector’s Aspect Ratio setting is accessed through the Resize button on the remote or
Video device connections
No video cables are provided with the projector. You can order cables from InFocus or
provide your own.
HDMI connection
HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI provides an
interface between sources, such as set-top boxes, DVD players, and receivers and your
projector. Plug an HDMI cable into the video-out connector on the video device and into the
HDMI connector on the projector.
Composite video connection
Plug the composite video cable’s yellow connector into the video-out connector on the
video device. Plug the other yellow connector into the yellow Video connector on the
projector.
VGA connection
If your video device has a 15-pin VGA output, plug one end of the included computer cable
into the VGA connector on your video source. This connector may be labeled “To Monitor”
on the video source. Plug the computer cable into either the Computer 1 or Computer 2
connector on the projector.
Download from Www.Somanuals.co1m1. All Manuals Search And Download.
The Status Indicator Lights on top of the projector indicates the state of the projector and
can help you troubleshoot.
Shutting down the projector
Auto Off Time
The projector also has an Auto Off Time feature that automatically turns the projector off
after no active sources are detected and no user interaction with the projector is performed
Table 2: Indicator Lights
Turning off the projector
Status Indicator Light
Meaning
To turn the projector off, press the Power button on the remote or keypad. The lamp turns
off and the Power LED blinks blue for 30 seconds while the fans continue to run to cool the
lamp. If the Power Saving Mode feature is on and when the lamp has cooled, the LED lights
blue and the fans stop. If the Power Saving Mode feature is off and when the lamp has cooled,
the LED blinks blue and the fans stop. Unplug the power cable to completely power off the
projector.
POWER: Solid Blue
TEMP: Off
LAMP: Off
1. If the Power Saving Mode feature is on,
the projector is plugged in.
2. The projector is on and initialized.
3. The projector is in normal operation.
POWER: Blinking Blue
TEMP: Off
LAMP: Off
1. If the Power Saving Mode is off, the
projector is plugged in.
2. The projector is powering down and
the fans are cooling the projector.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it does not,
troubleshoot the setup.
POWER: Blinking blue
TEMP: Blinking red
LAMP: Blinking red
The projector fan(s) are not operating
correctly and the projector has been shut
down.
The lamp failed to ignite.
POWER: Solid blue
TEMP: Blinking red
LAMP: Blinking red
Contact Technical Support if the problem
to contact service.
POWER: Solid blue
TEMP: Blinking red
LAMP: Blinking red
The lamp has reached its end of life and
must be replaced. The lamp will continue
to operate until it fails.
Contact Technical Support. Repair may be
needed.
POWER: Solid blue
TEMP: Blinking red
LAMP: Off
1. The projector is overheating and the
lamp will be shut off. The fans will
continue to run.
2. The projector will not turn back on
until the cooling process is complete.
Download from Www.Somanuals.co1m2. All Manuals Search And Download.
Problem
Solution
Result
No start up screen
Correct image
Plug power cord into the projector
press the Power button
Startup
Screen
Press the SOURCE button.
activate laptop’s external port
Computer image projected
Only start up screen appears
Startup
Screen
A
A
A
Restart laptop
Download from Www.Somanuals.co1m3. All Manuals Search And Download.
Problem
Solution
Result
Press the Auto Image button on remote
Computer image projected
No computer image, just the words “Signal out of
range”
Adjust computer refresh rate (Windows 7: Control
Panel > Display > Screen Resolution > Advanced
Settings > Adapter tab). Varies per operating system.
A
Signal out of
the range
A
A
You may also need to set a different resolution on your
computer, as shown in the following problem, “image
fuzzy or cropped”
Only my laptop’s background appears, not the
Desktop icons
Change the Multiple Display setting to "Duplicate these
displays" (Windows 7: Control Panel > Display > Screen
Resolution). Varies per operating system.
Background and Desktop projected
A
A
A
A
Download from Www.Somanuals.co1m4. All Manuals Search And Download.
Problem
Solution
Result
Change the computer's "Resolution" setting to match
the projector's resolution (Windows 7: Control Panel >
Display > Screen Resolution). Varies per operating
system.
Image fuzzy or cropped
Image clear and not cropped
A
A
A
Correct image
Move projector, adjust height
Image not centered on screen
MDL: IN2128HDa
( PC )
FW: X.XX
Force Wide
Off
16
Off
0
Phase
Adjust horizontal or
vertical position in
Advanced Menu >
Image > PC... menu
Prevent PC Screen Saver
Sync Threshold
Tracking
0
Horz Position
Vert Position
0
6
Previous
Download from Www.Somanuals.co1m5. All Manuals Search And Download.
Problem
Solution
Result
Image not square
Adjust Keystone on keypad
Square image
Adjust Sharpness in the Basic Menu
Image not sharp
Correct image
MDL: IN2128HDa
FW: X.XX
(
Basic Menu
)
Aspect Ratio
Auto Image
Brightness
Contrast
Auto
Execute
50
50
Auto Keystone
Keystone
Off
0
Presets
Presentation
Sharpness
Volume
Ceiling Mount
16
16
Off
Advanced Menu
Correct image
Change aspect ratio to 4:3 or 16:9 in Basic Menu >
Aspect Ratio menu
Image does not fit 4:3 or 16:9 screen
MDL: IN2128HDa
(
Basic Menu
)
FW: X.XX
Aspect Ratio
Auto Image
Brightness
Contrast
◄ Auto ►
Execute
50
50
Auto Keystone
Keystone
Off
0
Presets
Presentation
Sharpness
Volume
Ceiling Mount
16
16
Off
Advanced Menu
Download from Www.Somanuals.co1m6. All Manuals Search And Download.
Problem
Solution
Result
Turn off Ceiling Mount in Basic menu
Correct image
Image upside down
MDL: IN2128HDa
FW: X.XX
( Basic Menu )
Aspect Ratio
Auto Image
Brightness
Contrast
Auto
Execute
50
50
A
A
Auto Keystone
Keystone
Presets
Sharpness
Volume
Ceiling Mount
Off
0
Presentation
16
16
◄ Off ►
Advanced Menu
Turn off Rear Project in Advanced Menu > Setup >
Image Setup... menu
Correct image
Image reversed left to right
MDL: IN2128HDa
( Image Setup )
Digital Zoom
Horz Shift
Vert Shift
Magnify Level
Horz Shift
Vert Shift
Ceiling Mount
Rear Project
FW: X.XX
100
50
50
0
50
50
Off
◄ Off ►
Previous
Adjust the items in the Advanced Menu > Image >
Color... menu
Projected colors don’t match source
Correct image
MDL: IN2128HDa
( Color )
FW: X.XX
Color
50
Red Gain
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset
Color Space
Color Temp
Gamma
50
50
50
50
50
50
Auto
Warm
CRT
50
COLOR
COLOR
Tint
White Intensity
100
Previous
Download from Www.Somanuals.co1m7. All Manuals Search And Download.
Problem
Solution
Result
Turn off the internal LCD display on your laptop
The video embedded in my PowerPoint presentation
does not play on the screen
Embedded video plays correctly
A
A
B
A
B
Make sure vents aren’t blocked, turn off the projector
and allow it to cool for one minute
Lamp turns on
Lamp won’t turn on, the projector is overheating
Startup
Screen
Overheating
indicator
Download from Www.Somanuals.co1m8. All Manuals Search And Download.
Problem
Solution
Result
Lamp turns on
“Replace lamp” message appears at startup, lamp
won’t turn on
lamp door
Startup
Screen
replace lamp
Still need assistance?
Quick Start Guide for support contact information.
This product is backed by a limited warranty. An extended warranty plan may be purchased
from your dealer. When sending the projector in for repair, we recommend shipping the unit
in its original packing material, or having a professional packaging company pack the unit.
Please insure your shipment for its full value.
Download from Www.Somanuals.co1m9. All Manuals Search And Download.
•
•
•
•
•
•
•
•
•
•
•
Auto Image button to resynch the projector to the source.
Help button to get help with connecting sources and improving the picture.
ESC button to go back to previous OSD menu.
Using the remote control
The remote uses two (2) AAA batteries (not provided). They are easily installed
by removing the cover from the remote’s back, aligning the + and - ends of the
batteries, sliding them into place, and then replacing the cover.
PC button to cycle through the Computer sources.
Caution:
Video button to cycle through Composite/S-Video/HDMI input sources.
Keystone buttons adjust the squareness of the image
•
When replacing the remote batteries, be aware that using batteries other
than AAA batteries may risk severe damage to the remote. When disposing
of the batteries, be sure to do so in an enviromentally proper manner.
Magnify buttons magnify and reduce the projected picture size.
Freeze button to pause the projected image.
•
•
•
•
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
Overscan button remove noise around the video image.
AV Mute button blanks the projected image and mutes audio.
Ensure the batteries' polarity (+/-) is aligned correctly.
Troubleshooting the remote
Do not mix new and old batteries together, or mix different types of batter-
ies together.
•
Make sure the batteries are installed in the proper orientation and are not
dead.
•
•
Replace the batteries as soon as they run out.
•
Make sure you’re pointing the remote at the projector or the screen, not the
computer, and are within the remote range of 15 feet (4.5m). For best
results, point the remote at the projector.
Remove batteries from the remote control when storing or not in use for a
prolonged period.
To operate, point the remote at the front of the projector (not at the computer).
The range of optimum operation is about 15 feet (4.5m).
shutdown info).
navigation
buttons
Press the remote’s Menu button to open the projector’s menu system. Use the
arrow buttons to navigate, and the Select button to select features and adjust
The remote also has:
•
•
Volume buttons adjust the sound.
Custom button that can be assigned to a special function, like Blank Screen or
•
Source button brings up a menu of all possible sources allowing the user to
switch the active source.
•
•
•
Blank button to blank the screen.
Mute button to silence the audio.
Download from Www.Somanuals.co2m0. All Manuals Search And Download.
Using the audio
Using the projector’s speaker
connect audio cable
Connect the audio source to the Audio 1/Audio 2 connectors to hear audio
through the projector speakers.
Amplified speakers may also be connected to the projector using the Audio Out
connector.
To adjust the volume, press the Volume buttons on the remote.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
•
Make sure the audio cable is connected to the Audio 1/Audio 2 connector on
the projector, and that the other end of the cable is connected to an Audio
Out connector on the source (not a “line-in” or “microphone” connector).
•
Make sure the volume is turned up enough. Press the Volume button on the
remote.
•
•
•
Make sure the correct source is active.
Adjust the audio source.
If playing a video, make sure the playback has not been paused.
Download from Www.Somanuals.co2m1. All Manuals Search And Download.
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of
their functions:
Right arrow - When the menu is displayed, the right arrow button navigates
through the menu.
Up arrow/Keystone - When the menu is displayed, the up arrow button navigates
through the menu. When the menu is not displayed, this button adjusts the
Down arrow/Keystone - When the menu is displayed, the down arrow button
navigates through the menu. When the menu is not displayed, this button adjusts
menu navigation
buttons
Left arrow - When the menu is displayed, the left arrow button navigates through
the menu.
Enter - Activates the selected On-Screen Display (OSD) menu item.
Menu/Exit - Turns on the On-Screen Display (OSD) menu. Goes back to previous
OSD menu, exits and saves menu settings.
Auto - Resynchronizes the projector to the source.
Blank - Displays a solid color or factory logo screen.
Source - Brings up a menu of available sources.
Download from Www.Somanuals.co2m2. All Manuals Search And Download.
Optimizing computer images
Presentation features
After the projector is running and the image is on the screen, you can optimize the
image using the onscreen menus. For general information on using the menus, see
Several features are provided to make giving presentations easier. Here is an
overview, details are found in the menu section.
•
The Custom key allows you to assign various features to the button. The
default effect is Source Info, which displays information about the projector
•
Select the User Preset in the Basic Menu before optimizing images and the
settings will be saved in that Preset.
•
•
•
•
•
•
The Search Screen option lets you change the appearance of the blank screen
Change the Aspect Ratio. Choose the option that best fits your input source
Auto Off Time is provided to automatically shut down the projector after
•
•
When the projector is connected to the computer via USB Type B, the up
and down arrows an be used as page up and page down controls.
When the projector is connected to the computer via USB Type B, the
projector will prevent the computer from going into screen saver mode
during your presentation.
Download from Www.Somanuals.co2m3. All Manuals Search And Download.
Optimizing video images
Customizing the projector
After your video device is connected properly and the image is on the screen, you
can optimize the image using the onscreen menus. Select the User Preset in the
Basic Menu before optimizing images and the settings will be saved in that Preset.
You can customize the projector for your specific setup and needs. See page 28
for details on these features.
•
For rear projection, turn Rear Project on in the Advanced Menu > Setup >
Image Setup... menu.
•
•
•
•
For ceiling mounted projection, turn Ceiling Mount on in the Basic menu.
Change the Aspect Ratio. Choose the option that best fits your input source
Specify which source the projector checks first for active video during power-
up.
•
•
•
•
•
•
•
•
•
Specify the function of the Custom key on the remote.
Turn the projector’s display messages on and off.
Turn on power saving features.
Specify appearance of blank screen and startup screen.
Specify the language viewed on the menus.
Save settings for the active source as a preset.
Download from Www.Somanuals.co2m4. All Manuals Search And Download.
Using the menus
1 To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) Use the
arrow buttons to move up and down to review the menu options.
keypad navigation
buttons
2 To enter a submenu, highlight the desired submenu and press > on the keypad
or Select on remote.
3 To adjust a menu setting, highlight the desired menu option and press < or >
to scroll through the available adjustments.
4 Press the Menu button to exit the menu system.
The menus are grouped by usage:
•
•
The Basic Menu provides common adjustments.
The Advanced Menu provides more complex adjustments.
MDL: IN2128HDa
FW: X.XX
( Advanced Menu )
MDL: IN2128HDa
FW: X.XX
(
Basic Menu
)
Image
3D Control
Color
Aspect Ratio
Auto Image
Brightness
Contrast
Auto Keystone
Keystone
◄ Auto ►
Execute
50
50
Off
0
Setup
Status/Service
PC
Video
Basic Menu
Presets
Presentation
Sharpness
Volume
Ceiling Mount
16
16
Off
Advanced Menu
Basic Menu
Advanced Menu
Download from Www.Somanuals.co2m5. All Manuals Search And Download.
Basic Menu
Basic Menu
MDL: IN2128HDa
FW: X.XX
( Basic Menu )
Aspect Ratio
Auto Image
Brightness
Contrast
Auto Keystone
Keystone
Presets
To adjust the following settings, highlight the setting, use the right and left arrows
to adjust the values.
◄ Auto ►
Execute
50
50
Off
0
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV
screens are usually 4:3. HDTV and most DVDs are 16:9.
Select Auto to have the projector choose the ratio. Choose Native to see the
unmodified input with no resizing by the projector. Select 16:9 to watch enhanced
widescreen DVDs.
Auto Image: resets the projector to the source.
Brightness: changes the intensity of the image.
Presentation
Sharpness
Volume
Ceiling Mount
16
16
Off
Advanced Menu
Contrast: controls the degree of difference between the lightest and darkest parts
of the picture and changes the amount of black and white in the image.
Auto Keystone: automatically corrects distorted images resulting from an angled
projection.
Keystone: adjusts the image vertically and makes a squarer image. You can also
adjust keystone from the keypad.
Presets: Presets are provided that optimize the projector for displaying computer
presentations and video images under certain conditions. Note: Users can save
their settings as a User Preset.
Sharpness: Changes the clarity of the edges of a video image. Select a sharpness
setting.
Volume: increases or decreases the audio volume.
increasing keystone
decreasing keystone
Ceiling Mount: turns the image upside down for ceiling-mounted projection.
Download from Www.Somanuals.co2m6. All Manuals Search And Download.
setting, turn off Auto, then choose RGB for computer sources or choose either
REC709 or REC601 for component video sources.
Advanced Menu
MDL: IN2128HDa
FW: X.XX
(
Advanced Menu
)
Color Temperature: changes the hue of the colors. Select a listed relative warmth
value.
Image
3D Control
Color
Setup
Status/Service
PC
Video
Gamma: select the appropriate gamma from among Video, Film, Bright, and CRT.
Basic Menu
Tint: adjusts the red-green color balance in the image of NTSC video images. The tint
setting applies to NTSC video sources only.
White Intensity: increases the brightness of whites that are near 100%.
PC:
Force Wide: when this is off, the analog locking algorithms choose the standard mode
resolution (4:3) as the preferred default resolution. When this is on, the analog locking
algorithms choose wide mode resolution (16:10) as the preferred default resolution.
Phase: adjusts the synchronization of the pixels to the pixel clock on analog computer
sources.
Advanced Menu
Image:
Prevent PC Screen Saver: prevents your computer from going into Screen Save
mode. The projector must be connected to the PC via a Type-B USB cable for this fea-
ture to work.
3D Control:
3D: allows you to enjoy 3D (stereoscopic) content. Your projector supports Auto,
Top-Bottom, Frame Sequential, Frame Packing, Side-by-Side formats for controlling
LCD shutter glasses. In addition to the projector, you will need a pair of 3D shutter
glasses, 3D content, and 3D compatible source. Ensure the glasses you choose are con-
sistent with the synchronization mode you will be using.
Sync Threshold: (progressive signals only) If a hardware device, such as a DVD player,
is not syncing properly with the projector, select this option to help it to sync when
connected to the projector.
Tracking: adjusts the pixel clock rate on analog computer sources.
3D Sync Invert: If the image appears to flutter, look odd or if the image depth looks off
or you experience eye strain, turn this feature on to see if the image improves.
Horizontal/Vertical Position: adjusts the position of a computer source.
Video:
Detect Film: determines whether the original source of the input video was film (pro-
Color
Color: adjusts a video image from black and white to fully saturated color. The color
setting applies to NTSC video sources only.
gressive) or video (interlaced).
Overscan: crops video sources to remove noise from outside the image.
Red/Green/Blue Gain: adjusts the gain of the red, green or blue channel of the image.
Set Black Level: analyzes the current input image and calculates an offset value which
is then added to the analog to digital converter black level value. This ensures optimum
black level for each analog source.
Red/Green/Blue Offset: adjusts the offset of the red, green or blue channel of the
image.
Color Space: applies to computer and component video sources. It allows you to
select a color space that has been specifically tuned for the input signal. When Auto is
selected, the projector automatically determines the standard. To choose a different
Download from Www.Somanuals.co2m7. All Manuals Search And Download.
•
•
•
•
•
Source Info: the default action. Shows the Source Info menu.
Projector Info: shows the Projector Info menu.
Overscan: removes noise around the image.
AV Mute: enables or disables AV Mute function.
Closed Captions: enables or disables Closed Captions.
Setup:
Audio Setup
Internal Speakers: turns the internal speaker on or off.
Computer 1: selects the audio input for Computer 1 signal.
Computer 2: selects the audio input for Computer 2 signal.
Video: selects the audio input for video source.
Keypad: enables or locks the projector keypad.
LiteBoard™Wand: selects the LiteBoard™Wand mode. Options are: None, Single Pen
HDMI: selects the audio input for HDMI signal.
Closed Captioning
Closed Captions: controls closed captioning. If the source is NTSC and contains cap-
tions on the selected channel, then the projector will display caption text overlaid on
the image. Options are: Off, CC1 and CC2.
Image Setup
Digital Zoom: reduces the size of projector’s display area. If the display area has been
resized by this setting, it can be moved by changing the Horz Shift and Vert Shift set-
tings.
Magnify Level: magnifies the image. If the image has been magnified by this setting, it
can be moved by changing the Horz Shift and Vert Shift settings.
Ceiling Mount: turns the image upside down for ceiling-mounted projection.
Rear Project: reverses the image so you can project from behind a translucent screen.
Keypad/Remote Settings
Blank Key: select what to display when the blank key on the remote is pressed: a solid
color screen (blue, black or white), or the factory logo screen.
Custom Key: allows you to assign a different function to the Custom button, allowing
you to quickly and easily use the effect. Highlight an effect and press < or > to choose a
different one.
•
•
•
•
•
Blank Screen: displays a solid color or factory logo screen.
Mute: turns off all sound.
Source: brings up a menu of available sources.
Auto Image: resets the projector to the source.
Freeze Screen: pauses the projected image.
Download from Www.Somanuals.co2m8. All Manuals Search And Download.
To change the PIN:
Lamp
Programmed Dimming: When enabled, Programmed Dimming enhances contrast
Select “Change PIN...” in the Advanced Menu > Setup > PIN settings menu. Enter the
existing PIN. Enter the new PIN twice. Do not forget the new PIN. Contact InFocus
Support to recover a projector with a forgotten PIN.
ratios, lamp life and system noise performance. Lamp power will change continuously
based on the brightness of the program content. Note: Image anomalies may be seen
when image scenes change from dark to light (or light to dark). This is normal. Pro-
grammed Dimming works in conjunction with the lamp. If Lamp Low Power is enabled,
Programmed Dimming is unavailable. Note: Programmed Dimming is off by default.
Power
Power Saving Mode: When the Power Saving Mode is On and the projector is in
standby (powered off but connected to AC power), external audio and the Monitor
Out function will not work.
Lamp Low Power: toggles between on and off. Turn it on to lower the light output of
the lamp. This also lowers the fan speed, making the projector quieter.
AC Power On: When this feature is enabled, the projector automatically turns on
when power is connected. This allows control of ceiling mounted projectors with a
wall power switch.
OSD Setup
Language: allows you to select a language for the onscreen display.
Instant Power On: When this feature is enabled and it has been less than 1 minute since
the projector was powered down, you can turn the projector back on immediately.
When this feature is disabled, you will need to wait for the projector lamp to com-
pletely cool before restarting the projector.
Menu Position: allows you to change the position of the On Screen Display items.
Menu Transparency: allows you to change how much of the projected image behind
the menu you can see. As the value increases, more of the image behind the menu is
visible.
Eco Blanking: When this feature is enabled and no video source is sensed, 70% of lamp
power is saved and no image is shown. When the video source is again applied, the
image is shown immediately.
Show Messages: allows you to turn off status messages (such as “Searching”) in the
upper-left corner of the screen.
PIN Settings
Source
PIN Protect: The PIN (personal identification number) feature allows you to pass-
word protect your projector. Once you enable the PIN feature, you must enter the
PIN before you can project an image. Use the Left/Right/Up/Down arrows buttons on
the remote or keypad to set a 4-button press sequence. If you enter an incorrect PIN 3
times in succession, the projector will automatically shut down. If you lose or forget
your custom PIN, contact InFocus Technical Support.
Auto Source: When this feature is On, the projector automatically finds the active
source, checking the selected Power-up Source first. When this feature is Off, the pro-
jector defaults to the source selected in Power-up Source. To display another source,
you must manually select one by pressing the Source button on the remote or keypad
and selecting one from the displayed Source menu.
Power-up Source: determines which source the projector checks first for active
video during power-up.
To enter the PIN at projector startup:
Power up the projector. The “Enter PIN” dialog box appears after the startup screen.
Enter the default PIN or the new PIN (Left/Right/Up/Down) if it has been changed,
using the arrow buttons on the remote or keypad. See the description above for
instructions.
Search Screen: allows you to display a blank screen instead of the default screen at
startup, and when no source is detected.
Download from Www.Somanuals.co2m9. All Manuals Search And Download.
Timer
Auto Off Time: automatically turns the projector off after no signals are detected for
Wireless LAN
SSID: Display the projector’s SSID information.
IP Address: a read-only display of IP Address.
Subnet Mask: a read-only display of Subnet Mask.
Restart Network: Restart network settings.
a preset number of minutes. If an active signal is received before the projector powers
down, the image will be displayed.
High Altitude Setting
High Altitude: We recommend you turn on the High Altitude Mode when your envi-
ronment is between 5000' (1500m) and 10,000' (3000m) above sea level.
Status/Service:
Source Info: a read-only display of current source settings.
Network
Projector Info: a read-only display of current projector settings.
Wired LAN
Reset Lamp Hours: resets the lamp hours used counter in the Projector Info
menu to zero. Do this only after changing the lamp.
DHCP: Abbreviation for Dynamic Host Configuration Protocol. This
protocol automatically assigns IP Addresses to networked devices.
•
When the “DHCP” is set to “On”, the DHCP server will assign an
IP address to the projector automatically. This may take up to a
minute.
Factory Reset: restores all settings to their factory default settings.
Service Code: only used by authorized service personnel.
•
When the "DHCP" is set to "Off", the user will need to set the IP
address manually.
IP Address: The numerical address used to identify devices on the net-
work. This is only accessible when DHCP is set to Off.
•
The IP Address is the number that identifies this projector on the
network. You cannot have two devices with the same IP Address
on the same network.
•
The IP Address “0.0.0.0” is prohibited.
Subnet Mask: A numeric value defining the number of bits used in an IP
Address when the network is divided into subnets. This function can
only be used when DHCP is set to Off.
•
The Subnet Mask “0.0.0.0” is prohibited.
Default Gateway: A server (or router) to communicate across networks
(subnets) that are divided by a Subnet Mask. This function can only be
used when DHCP is set to Off.
DNS: Setup DNS server address when DHCP is disabled.
MAC Address: Abbreviation for Media Access Control Address. A MAC
Address is a unique ID number assigned to each network adapter.
Apply: Save and execute the wired network settings.
Download from Www.Somanuals.co3m0. All Manuals Search And Download.
Photo mode
Multimedia EZ Suite Menu
Use the arrow keys to navigate up and down, left and right. The right-hand menus change
based on the left-hand menu selection.
To select a menu option, press the right-hand arrow.
To return to the previous EZ Suite menu (and ultimately the EZ Suite main menu), press the
Menu or left arrow key.
EZ Media
Internal Memory
Press to Exit
Folders and supported files are represented in thumbnail view.
Internal Memory
USB
EZ Media
Key
Action
EZ Display
Settings
Up
EZ Suite
Down
Left
Scroll through the thumbnails
With a mini-B USB cable connected to your PC and the projector, you can load internal
information on how to connect to download internal memory.
Right
Opens and closes the file
Select/Enter
Menu
USB
Exit thumbnail view and return to EZ Suite main menu
When a USB storage device is inserted into the projector USB Type-A connector, press the
Source key and use the arrow keys to highlight Multimedia. Press the Select key on the
remote (or the Enter key on the projector) to select the multimedia source. The Multimedia
EZ Suite menu displays.
Internal Memory
USB
Photo
Video
Music
Office viewer
EZ Suite
Download from Www.Somanuals.co3m1. All Manuals Search And Download.
Displaying a picture
Video mode
Internal Memory
USB
Photo
Video
Music
Office viewer
EZ Suite
Browse Mode
Press to Exit
•
•
•
To open/close the Photo View toolbar: press the Menu key.
To navigate through the toolbar: press the arrow keys ^/</>.
To return to thumbnail view: press the Select/Enter key.
Video playlist is displayed on the screen
Toolbar icon
Action
Key
Action
Press v/Enter/Select to select picture rotation
Toggle the Enter/Select/four arrow keys to rotate the picture
counterclockwise, press Menu key to exit from it.
Go to the previous video file
Go to the next video file
Up
Down
Select/Enter
Menu
Toggle Enter/Select to zoom in the picture by x0, x1, x2, x3, x4 in
sequence, press Menu key to exit from it.
Play the video
Exit video playlist and return to EZ Suite main menu
Toggle v/Enter/Select to display the previous picture
Toggle v/Enter/Select to display the next picture
Press v/Enter/Select to start slideshow when Slideshow is On, press
Menu key to stop the slideshow. Note: To enable the Slideshow
feature and set the slide timing, go to the Settings menu and adjust
Slideshow and Slideshow Duration.
Press v/Enter/Select to open the pop-up message screen, press Menu
key to close it.
Press v/Enter/Select to open the pop-up message screen, press Menu
key to close it.
Press v/Enter/Select to display the current file information
Press v/Enter/Select to return to thumbnail view
Download from Www.Somanuals.co3m2. All Manuals Search And Download.
When a video is playing
•
Repeat mode: set in the EZ Suite Settings > Video menu > Repeat Mode. See
moviesample.mp4
00:00:02
00:00:00
00:04:12
•
•
To open the Video Viewer toolbar: press the Menu key.
To stop the video or return to video playlist: press the Select/Enter key
when the toolbar is closed.
Fast forward
Pause
Rewind
Play
Repeat mode
•
•
To pause/play the video file: Press the Select/Enter key to pause and play
the video file when the toolbar is displayed.
To rewind the video file: Press the Menu key to open the Video Viewer
toolbar. Press the left arrow key to rewind the video and toggle through the
different rewind speeds. Press the Select/Enter key to stop rewinding.
Options include: X1, X2, X4, and X8.
•
•
To fast forward the video file: Open the Video Viewer toolbar, press the
right arrow key to fast forward the video and toggle through the different
forward speeds. Press the Select/Enter key to stop forwarding. Options
include: X1, X2, X4 and X8.
To adjust volume: Press the Volume Up and Down keys on the remote to
increase and decrease the volume.
Download from Www.Somanuals.co3m3. All Manuals Search And Download.
When audio is playing
Music mode
Music
Photo
mp3
Internal Memory
USB
Video
Music
Office viewer
00:30:00
00:00:00
01:30:00
EZ Suite
Press to Exit
The audio playlist is displayed on the screen.
•
To return to audio playlist: press the Menu key.
Key
Action
Pause
Fast forward
Previous
Go to the previous audio file
Go to the next audio file
Up
Play
Down
Left
Rewind
Next
Display the sort type
Play the audio file
Select/Enter
Menu
Exit audio playlist and return to EZ Suite main menu
•
•
•
•
•
•
To pause/start the audio file: Press the Select/Enter key to pause and start
the audio file.
To rewind the audio file: Press the left arrow key to rewind the audio. Press
again to return to normal speed.
To fast forward the audio file: Press the right arrow key to fast forward the
audio. Press again to return to normal speed.
To adjust volume: Press the Volume Up and Down keys on the remote to
increase and decrease the volume.
To go to the previous audio file: Press left arrow key twice within one
second.
To go to the next audio file: Press the right arrow key twice within one
second.
Download from Www.Somanuals.co3m4. All Manuals Search And Download.
When an Office file is displaying
Office viewer mode
Office viewer
Photo
Video
Internal Memory
Music
USB
Office viewer
EZ Suite
Press to Exit
The file list is displayed on the screen.
•
Press the Menu key to open/close the Office Viewer toolbar. Use the right
or left arrow key to highlight the desired function. Then press the Select/
Enter key.
Key
Action
Go to the previous file
Go to the next file
Up
Down
Left
Display the sort type
Fit to Screen/Fit to
Width/Fit to Height
Open a file
Select/Enter
Menu
Scroll
Right
Scroll
Left
Zoom
In
Scroll
Up
Close
Toolbar
Scroll
Down
Zoom
Out
Exit file list and return to EZ Suite main screen
•
To return to the filelist: close the toolbar first, and press Select/Enter key.
Note: The file name displays in the upper left corner of the Office Viewer toolbar. The
current page number and number of pages appears on the upper right corner. The
amount of magnification displays on the lower right corner.
Download from Www.Somanuals.co3m5. All Manuals Search And Download.
Supported file formats
Images
•
Video
•
File
Audio/
Codec
Profile/Level Support Explanation
No limitations
Extensions Video
Image Format Profile
Baseline
Color Space
Size Limitation
MJPEG
H.264/AVC
YUV400
YUV420
YUV422
YUV440
YUV444
YUV400
YUV420
YUV422
YUV440
YUV444
No limit
No limit
No limit
No limit
No limit
No limit
Up to High Profile ,
Levels 1- 4.1 (1080P
30fps 20Mbps)
Only supports 1-3
reference frames.
XVID
Up to Advance Simple
profile (1080P 30fps
20Mbps)
Main profile, Low and
Main Levels (1080P
30fps 20Mbps)
Advanced Simple Profile
(frame picture) , Levels
0-5 (1080P 30fps
20Mbps)
.avi
.divx
.mkv
JPEG
Progressive
Width <= 10240 &
height <= 6400
Video
MPEG2
MPEG4
BMP
No limit
No limit
MPEG2
Main profile, Low and
Main Levels (1080P
30fps 20Mbps)
Up to High Profile ,
Levels 1- 4.1 (1080P
30fps 20Mbps)
Main profile, Low and
Main Levels (1080P
30fps 20Mbps)
Main profile, Low and
Main Levels (1080P
30fps 20Mbps)
•
Audio
Audio Format
Sample rate (KHz)
Bit Rate (Kbps)
.ts
Video
H.264/AVC
MPEG1
Only supports 1-3
reference frames.
OGG
8-48
8-48
8-48
8-48
64-320
32-384
128-1536
8-256
ADPCM-WAV
PCM-WAV
AAC
D-frames used for
fast previews are
not supported.
Video
Audio
.dat
.vob
.mpg
.mpeg
MPEG2
•
Voice Record
File Format
.wav
Audio Format
IMA-ADPCM
Sample rate (KHz) Bit Rate (Kbps)
MPEG-1 Layer
I, II
MPEG-1 Layer
III (mp3)
8
32
64
192
384
16
24
48
MPEG4
Advanced Simple Profile
(frame picture) , Levels
0-5 (1080P 30fps
20Mbps)
Up to High Profile ,
Levels 1- 4.1 (1080P
30fps 20Mbps)
.mov
.mp4
Video
H.264/AVC
Only supports 1-3
reference frames.
Download from Www.Somanuals.co3m6. All Manuals Search And Download.
BritishWord Because Office Viewer
•
Subtitle
95.
does not load all pages
of a Word file
Format
Font
Subtitle Size
Word 97,
2000,2002,
2003.
Word
2007(.docx),
2010(.docx)
Simplified Chinese
Up to 100MB bold text is not
supported.
simultaneously, there
are no obvious page or
line limitations.
MS Word
Standard SRT
UTF-8 / UTF-16
4bits up to 448x200
2bits up to 896x200
Note: Mixed subtitle codes are NOT supported.
•
Office Viewer
British Excel Maximum number of
5, 95.
rows: 595
Support
Version
Size
Excel 97,
Maximum number of
File Format
Pages/Lines Limitation
Comment
-
Limitation
2000, 2002, columns: 256
2003.
Password-
protected
PDF 1.0
PDF 1.1
MS Excel
Up to 15MB
documents are not
Excel
Maximum number of
supported.
2007(.xlsx), sheets: 100
2010(.xlsx).
Up to 1000 pages (One
File)
Adobe PDF PDF 1.2
PDF 1.3
Up to 75MB
Office XP
Excel.
All of the three above
limitations apply.
PDF 1.4
British
PowerPoint
97
PowerPoint
2000
PowerPoint
2002
PowerPoint
2003
PowerPoint
2007 (.pptx)
PowerPoint
2010 (.pptx)
MS
PowerPoint
Office XP
PowerPoint
PowerPoint
presentation
2003 and
earlier (.pps)
PowerPoint
presentation
2007 and
2010 (.ppsx)
Download from Www.Somanuals.co3m7. All Manuals Search And Download.
NOTE: Win8 doesn't support extension mode.
System Requirements
Windows OS:
EZ Display
EZ USB
The EZ USB allows you to project using EZ USB application from a Windows or Macintosh
operating system through a USB mini-B connection.
CPU
Dual Core 2 GHz or higher (ATOM not supported)
Graphic card
Operating System
USB
Intel, nVIDIA or ATI graphic card with 64MB VRAM or above
Windows XP SP3, Vista SP2, Windows 7 SP1, Windows 8
USB 2.0 High Speed
EZ Media
EZ USB
EZ Display
EZ Mobile
Miracast
EZ Display
Settings
NOTE: Audio is not supported on XP.
Mac OS:
EZ Suite
CPU
Dual Core Intel Core i 1.4 GHz or higher
(PowerPC not supported)
Graphic card
Intel, nVIDIA or ATI graphic card with 64MB VRAM or above
Mac OS X 10.7 and above
Operating System
Recommended
Models
Mac Book series and iMac series after E/2011
Recommended System Configuration
Windows OS:
CPU
Dual Core Intel Core i5 2.4Ghz
Memory
DDR 4GB
1 Connect one end of the USB cable to the USB Mini-B connector on the
projector and the other to the USB Type-A connector on your computer.
Graphic card
Operating System
USB
256MB VRAM or above
Windows XP SP3, Win 7 SP1 or Win 8
USB 2.0 High Speed
2 Go to Multimedia > EZ Display > EZ USB to connect your device.
Mac OS:
3 If your computer doesn’t support auto play, go to "My Computer", you will
find a removable disk and EZ_USB disk drive, then double click it to install the
USB driver and EZ USB application.
CPU
Dual Core Intel Core i5 2Ghz
DDR 4GB
Memory
Graphic card
Operating System
256MB VRAM or above
Mac OS X 10.8
4 Launch EZ USB to project the contents on your computer.
Features
Recommended
Models
Mac Book series and iMac series after E/2011
•
•
•
Full Screen Mirror Display and Extended Display
USB2.0 High Speed Transfer
support.
EZ Display
OS support: Windows XP 32/64bit SP3 (Professional or above), Windows
Vista 32/64bit SP2 (Home premium and above), Windows 7 32/64bit SP1
(Home premium and above) and Windows 8, Mac OS 10.7 and later
EZ Display allows you to project using the EZ Display application from a Windows PC,
Android, Macintosh or iOS device either wirelessly using the optional SP-WIFIUSB-2 adapter
or using the LAN connection.
Download from Www.Somanuals.co3m8. All Manuals Search And Download.
Wired LAN connection
• If the RJ45 cables are not properly connected, the IP Address, Subnet Mask,
Default Gateway, DNS and MAC Address settings will display 0.0.0.0. Make
sure the cables are properly connected and perform the procedures above
again.
Internet
IP Router
• If you need to connect to the projector in its standby mode, set the Power
Saving Mode feature to Off.
If you are in a non-DHCP environment:
1 Repeat steps 1-2 above.
1 Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the
projector and the other end to the RJ45 port .
2 Press v to highlight DHCP and press < or > to select Off.
3 Contact your network administrator for information on the IP address, Subnet
Mask, Default Gateway and DNS settings.
2 Press Menu on the keypad or remote and then go to Advanced Menu > Setup
> Network > Wired LAN menu.
4 Press ^ or v to select the item you want to modify.
MDL: IN2128HDa
( Wired LAN )
FW: X.XX
DHCP
◄ On ►
IP Address
Subnet Mask
Default Gateway
DNS
MAC Address
Apply
192. 168. 0. 160
5 Press < or > to move the cursor and then press ^ or v to select the value.
6 Press v to highlight Apply and press > to save the settings.
255. 255. 255.
0
192. 168. 0.
0. 0. 0.
1
0
8C. 9A. 77. 00. 00. 01
Execute
Previous
• If the RJ45 cables are not properly connected, the IP Address, Subnet Mask,
Default Gateway, DNS and MAC Address settings will display 0.0.0.0. Make
sure the cables are properly connected and perform the procedures above
again.
• If you wish to connect to the projector in its standby mode, be sure to
select RJ45 and obtain the IP Address, Subnet Mask, Default Gateway, DNS
and MAC Address information when the projector is on.
3 Press v to highlight DHCP and press < or > to select On.
4 Press v to highlight Apply and press >.
5 Please wait for around 15 - 20 seconds, and then re-enter the Network page.
The IP address, Subnet Mask, Default Gateway, DNS and MAC Address
settings will be displayed. Write down the IP address displayed in the IP
address row.
• If the Projector IP Address still does not display, contact your network
administrator.
Download from Www.Somanuals.co3m9. All Manuals Search And Download.
Wireless LAN connection
Setup > Network > Wirless LAN menu.
To connect to the projector wirelessly, you need to plug an optional InFocus
wireless dongle (p/n SP-WIFIUSB-2) to the USB Type A connector on the
projector.
MDL: IN2128HDa
FW: X.XX
( Wireless LAN )
SSID
IN2128HDa-606326
IP Address
Subnet Mask
192. 168. 111.
255. 255. 255.
1
0
InFocus wireless dongle
(p/n SP-WIFIUSB-2)
Previous
5 Write down the IP address for network connection.
How to setup AP mode:
How to setup client mode:
1 Make sure the projector is turned on.
1 Select Multimedia from source list.
2 Select Multimedia from source list.
mode is set to ON by default.
3 Choose the Wi-Fi network which the projector connect to from the Wi-Fi
network list, and press Select/Enter.
4 Press Select/Enter to display on-screen keyboard, enter the password from
the on-screen keyboard, then press Menu to close the keyboard.
AP Mode
SSID
IN2128HDa-606326
Open
Security
PSK
Channel
11
Auto
4 Press Source then press Menu to display OSD menu. Go to Advanced Menu >
5 Highlight OK and press Select/Enter to connect.
6 Press Source then press Menu to display OSD menu. Go to Advanced Menu >
Download from Www.Somanuals.co4m0. All Manuals Search And Download.
Setup > Network > Wirless LAN menu.
EZ Suite Settings
MDL: IN2128HDa
FW: X.XX
( Wireless LAN )
EZ Display
SSID
135
IP Address
Subnet Mask
192. 168. 43. 10
255. 255. 255.
0
Settings
System
Video
Previous
Photo
Music
WiFi
EZ Suite
•
Press the Select/Enter to enter the selected item. Press the Menu key to
exit.
EZ Mobile
System
Version
Description
EZ Mobile allows you to connect wirelessly to a media server and DLNA enabled devices.
Please note: The file compatibility is not the same as EZ Display. Refer to the EZ Mobile
guide for compatibility information.
This is the version of EZ Suite software on your projector.
This is a read only field.
Displays the current OSD (on-screen display) language.
Using the up and down arrow keys, highlight the desired
language and press the Select key.
Language
EZ Miracast
EZ Miracast enables wireless delivery of audio and video to or from desktop, tablets, mobile
phones, and other devices. EZ Miracast supports SP-WIFIUSB-2 adapter only.
For Service Use Only.
Update
Displays the current host name for the projector. This will
be displayed when using one of the wireless apps. To
change the Hostname, highlight Hostname and press the
Select key. Using the arrow keys and onscreen keyboard,
highlight each alphanumeric character/symbol and press the
Select key. Repeat until the hostname is complete. Press
the Menu key to exit the keyboard.
Hostname
Highlight and select to connect the projector directly to a
PC or MAC for downloading photos/video/audio/office
documents directly to the internal memory of the
projector.
UsbSwitch
Video
Description
Sets the display (aspect) ratio.
Sets repeat mode
Display Ratio
Repeat Mode
Download from Www.Somanuals.co4m1. All Manuals Search And Download.
Web controlling the projector
Once you have the correct IP address for the projector and the projector is on or
in standby mode, you can use any computer that is on the same local area network
to control the projector.
Photo
Description
Sets the display (aspect) ratio
Enables slide show mode
Display Ratio
Slideshow Pattern
Slideshow Duration
• Use only Microsoft Internet Explorer version 7.0 or higher.
Sets the time interval each image displays
1 Enter the address of the projector in the address bar of your browser and
press Enter.
Music
Description
Sets repeat mode
Repeat Mode
WiFi
Description
2 The main page of the Network Control displays.
Sets AP mode on/off. AP mode is set to ON by default. See
page 40 for more details.
AP Mode
Client Mode
i
* WiFi only works when the InFocus wireless dongle (p/n SP-WIFIUSB-2) is connected.
ii
i.
ii. The Crestron (eControl) page displays the Crestron eControl user inter-
Download from Www.Somanuals.co4m2. All Manuals Search And Download.
3 To access the Admin page, enter the password. The default password is
“0000”. If you forget the password, please go to Advanced Menu > Setup >
Network > Restart Network to restore the password to the default code.
®
About Crestron e-Control
®
1 The Crestron e-Control page provides a variety of virtual keys to control the
projector or adjust the projector’s image.
i
i
•
•
•
Information: Displays the status, wired LAN, and wireless LAN information.
Network Settings: Provides network settings.
You can press </>
to reveal more
buttons.
Email Alert: Allows you to setup the mail server and send system error
messages to your network administrator.
•
Control Panel: Provides some OSD menus such as Basic Menu, Image,
details.
i.
These buttons function the same as the OSD menus and remote control
functions.
•
•
Basic Menu: Provides some common adjustments in Basic Menu.
•
Source List: To switch the source, click on the desired source.
Image: Provides some common adjustments in Image settings under
Advanced Menu.
•
Menu: Use to go back to the previous OSD menu, exit and save menu
settings.
•
Setup: Provides some common adjustments in Setup settings under
Advanced Menu.
•
When you use the projector control panel or remote control to change the
OSD menu settings, it may take a while for the web browser to synchronize
these changes with the projector.
•
•
Status Service: Provides Reset Lamp Hours and Factory Reset settings.
Crestron Control: Displays the Crestron eControl user interface. See
page 43 for details.
Download from Www.Somanuals.co4m3. All Manuals Search And Download.
Please pay attention to the input length and character limitations (including
character and punctuation restrictions) listed below:
2 The Tools page allows you to manage the projector, configure the LAN
control settings and remotely access the network operations of this projector.
Maximum Number of
Characters
Input-Length
IP Address
IP ID
Port
15
2
5
Crestron Control
ii
iii
Projector Name
Location
10
9
i
Projector
Assigned To
DHCP (Enabled)
IP Address
Subnet Mask
Default Gateway
DNS Server
Enabled
9
(N/A)
15
15
15
15
(N/A)
20
2
Network
Configuration
User Password
New Password
Confirm
Enabled
New Password
Confirm
(N/A)
20
20
Admin Password
i.
This area is only used with a Crestron Control System. Please contact Cre-
ston or refer to the Crestron user manual for setup information.
/ > < $ % + \ ' " are prohibited.
ii. This area is used for naming the projector, associating it with a particular
location, assigning a responsible party to it, and adjusting network settings.
iii. This area is used to set User and Admin passwords. When password protec-
tion is enabled, unauthorized changes to the projector configuration will be
avoided.
• To prevent errors, only enter alphanumeric characters on the Tools page.
• After configuring the settings, press the Send button and the data will be
saved in the projector.
• Press exit to go back to the Crestron remote network operation page.
Download from Www.Somanuals.co4m4. All Manuals Search And Download.
3 The Info page displays the information and status of this projector.
Crestron RoomView
From the Crestron RoomView software in the Edit Room page, enter the IP
Address (or hostname) as shown on the projector’s on-screen display (OSD)
menu, “05” for IPID, and “41794” for the reserved Crestron control port.
Press exit to go back to the Crestron remote network operation page.
4 After pressing the Contact IT Help button, the Title window will display in the
upper right corner of the screen. You will be able to send messages to
RoomView™ software administrators/users who are connected to the same
local area network.
For the Crestron RoomView user guide and information about RoomView settings
and commands, go to: http://www.crestron.com/products/
roomview_connected_embedded_projectors_devices/resources.asp
•
Download from Www.Somanuals.co4m5. All Manuals Search And Download.
6 Enter the passcode on the Multimedia > EZ Display > EZ Display screen.
Displaying Images through EZ Display
Installation for Windows and Macintosh
Ethernet Host Info.
IP Address: 192.168.0.160
EZ Display is an application which can run on the host PC. It helps connect your
computer to an available network projector and transfer the desktop content to
the network projector via local network connection.
Passcode: 9147
2 Download the correct EZ Display for your computer type (MAC or PC).
3 When the download is complete, install the software to your computer by
clicking the exe file. Follow the on-screen instructions to complete the
installation.
For more information about the applications EZ USB and EZ Display, review these
manuals at www.infocus.com/support:
4 Launch EZ Display, click “Enter IP Address” or “Auto Search” to select a
connection type to the projector, then click “Start”.
•
•
•
•
•
•
EZ USB Display Manual(Win+Mac)
EZ Display Manual-Mac
EZ Display Manual-Win
5 Select a display mode by clicking “Mirror” or “Extension”. If you are connected
to the projector both through the wired and wireless connections, a list of the
two devices is displayed.
EZ Mobile Operation
EZ Display - EZ Remote Manual-Android
EZ Display - EZ Remote Manual-iOS
Download from Www.Somanuals.co4m6. All Manuals Search And Download.
Using EZ Display
Projecting from Smartphones/Tablets
EZ Display is a special program to project your iOS or Android device display to a
projector through a WiFi connection. You can remotely control the projector,
decode document files, link to your dropbox account, surf the web, view photos,
display a live camera feed and transfer files wirelessly. You can even annotate
documents, webpages and photos and save them for sharing.
i
ii
System Requirements
iOS
iii
iv
iOS
iOS 5.1 and above
v
Device
All iPhone model after iPhone 3GS
All iPad model after iPad 2
All iPod touch after iPod touch 4th generation
iPhone: 480x320~1136x640
iPad: 1024x768~2048x1536
i.
Split Screen: Display up to 4 computers or mobile devices in Split Screen
using the 1, 2, 3, 4 buttons or 2 displays using the L and R buttons.
Resolution support
ii. Mirror/Extended Display: To duplicate your computer display onto the pro-
jector, click Mirror. To extend your desktop display onto the projector, click
Extension.
iii. Video/Graphic Display: To display the best image quality, but with a slightly
slower transmission speed, click Video. To display images faster, but with
slightly less quality, click Graphic. Note: Transmission performance is deter-
mined by your network speed.
iv. Compatibility Mode: Check the Compatibility mode box, if the projector is
having trouble displaying video from any media players.
v. Audio Streaming: To turn Audio Streaming on or off, click On or Off as
appropriate.
Storage
At least 20MB free space needed
Android
OS
Android ICS 4.0 and above
1Ghz above
CPU
Memory
Storage
1GB DDR above
At least 20MB free space needed
Installation for Android and iOS
Search for “EZ Display” and “EZ Remote” in Google Play or App Store, then
download and install the applications. Before downloading, please make sure your
device is supported.
Note: Supported functions vary per computer’s operating system.
Start up
1 Insert the optional USB WiFi Adapter (SP-WIFIUSB-2) into the USB Type A
input.
2 Establish Wifi connection with your mobile device according to the projector
WiFi setup. If in AP mode connect directly to the projector. If in Client mode
connect to the same WiFi access point as the projector. Launch the EZ Display
or EZ Remote app on your mobile device.
Download from Www.Somanuals.co4m7. All Manuals Search And Download.
EZ Display
Launch EZ Display and it will scan for and list the device's IP address. When you
click the device, a passcode is required. Enter the 4 digit number shown on your
projector. After entering the correct passcode on the Multimedia > EZ Display >
EZ Display page, EZ Display will display and allow you to select the different
feature options.
Android screen
iOS screen
EZ Remote
Launch EZ Remote. You will see the connected device shown on the device list.
Click it to enable Remote control.
Passcode: 5774
Android screen
iOS screen
Android screen
iOS screen
*Skin button is reserved for future feature.
Download from Www.Somanuals.co4m8. All Manuals Search And Download.
EZ Display: Streaming Doc and Doc Viewer
EZ Display: Pix Viewer
To display your photos, select Photo Gallery and select your photo. You can also
draw on it with the Sketch feature.
To stream your documents, transfer the documents you want from the computer
to your mobile device and disconnect your mobile device. Documents will be
organized by their format type.
iOS screen
Android screen
Select a file to display it wirelessly. Click the Sketch icon to begin drawing and
annotating your file. Click Save when you are done editing.
EZ Display: Live Cam
Live Cam will project what your camera sees in real-time. You can adjust the
image quality and switch between the front or rear view of the camera. When you
pause the camera stream, you can enable Sketch and zoom in/out the current
image. You can also save your camera stream as a camera roll.
iOS screen
Android screen
iOS screen
Android screen
Download from Www.Somanuals.co4m9. All Manuals Search And Download.
EZ Display: Streaming Web
EZ Display: Dropbox
The web browser will be displayed over WiFi. The Sketch and Save functions are
also supported. This feature requires a Client Mode internet connection. See
page 40 for more details. Select web browser. The default home page is
Select Dropbox and log in to your existing Dropbox account. Choose documents
and photos to display. This feature requires a Client Mode Wifi connection
Passcode: 5774
iOS screen
Android screen
iOS screen
Android screen
Download from Www.Somanuals.co5m0. All Manuals Search And Download.
EZ Display: Split Screen
EZ Display allows up to 4 different sources to be displayed in the same screen.
NOTE:
•
•
Hybrid OS support: Windows, Mac OS, iOS, and Android
Supports all web, sketch and other functions except EZ Stream.
Android screen
iOS screen
Download from Www.Somanuals.co5m1. All Manuals Search And Download.
4 Connect the projector and your computer with a VGA cable.
5 Make sure the wand's battery is charged or charging.
LiteBoard™ Wand
The optional LiteBoard™ Wand (p/n HW-LBWAND-02), when combined with
the LiteBoard Wand dongle (p/n HW-LBRADIO), works like a wireless mouse -
but one that works in midair, not on your desktop. Just hold the wand in your
hand, and point it at the projected image to point, click and drag. The wand works
with all your software, just like a regular mouse.
6 Turn on the projector and make sure it's displaying the computer's screen -
set the source to Computer 1 or Computer 2 (press the source button on the
projector or its remote if needed - you may need to press it several times).
Charging the Wand’s Battery
7 Enable the LiteBoard™ Wand in the Advanced Menu > Setup > Keypad/
Remote menu.
When the wand’s red battery light starts to blink, its internal battery is low (if the
battery is fully discharged, you won’t be able to turn the wand on by pressing its
tip, left or right mouse buttons).
8 Turn on the wand by pressing its tip, left or right mouse button - 2 blinks of
the blue status light means the wand is searching for a connection. When
connected the light will be lighted continuously.
To charge the battery, open the flap on the right side of the wand to expose the
wand’s USB connector. Then connect a USB cable between the wand and a USB
power adapter (not included), or a computer (if connecting to a computer, make
sure the computer is powered on). The battery light will stay on while the battery
is charging, then it will turn off when the battery is fully charged.
9 Point the wand at the screen to point, click, and drag - just like a normal
mouse.
When charging is finished, you can disconnect the USB cable (or keep the cable
connected and use the wand while it’s charging).
NOTE: When you’re done, set the wand aside and make sure it isn’t pointing at
the screen; it will turn itself off automatically after 1 minute.
NOTE: 5-10 minutes of charging is enough for about an hour of wand use. A full
charge will take 3-4 hours and will allow 20-40 hours of non-stop wand use. A fully
charged, new wand will hold a charge in standby for up to 3 weeks.
Caution: The lithium battery is only rechargeable, and is not user serviceable or
user replaceable.
Caution: Always use a USB cable and power adapter (or your computer) to charge
the wand.
MOLEX
How to Use the Wand
1 Connect the LiteBoard™ Wand dongle (p/n HW-LBRADIO) to the LiteBoard
Radio connector of the projector.
2 The projector needs to be powered on and connected to your computer.
3 Connect the projector and your computer with a USB cable (USB Type A to
USB Type B).
Download from Www.Somanuals.co5m2. All Manuals Search And Download.
Wand Position and Avoiding Shadows
Your Location Distance from the Screen
Using More than One Wand
The projector can work with two wands at the same time.
You can use the LiteBoard™ Wand right up against the screen, or around the
room. You might find that your pointing accuracy will improve if you get closer to
the screen. Also, avoid standing too far off from either side of the screen.
1 Enter the Keypad/Remote menu under Advanced Menu> Setup > Keypad/
Remote menu.
Avoid Shadows!
2 Scroll to the LiteBoard™ Wand function.
The wand won't work if its sensor is in a shadow or if it is pointing at a shadow:
3 Select the desired setting:
Correct (no shadow)
Incorrect (shadow)
None = No Liteboard Wand (Default)
Single = Use 1 Liteboard Wand
Dual = Use 2 Liteboard Wands
When you want to switch to a different wand:
1 Point the current wand away from the projected image for at least 3 seconds.
2 Press the tip, left or right button on the new wand to turn it on, and then start
using the new wand.
How to Hold the Wand
NOTE: You can access the LiteBoard™Wand menu from the projector's Setup >
Keypad/Remote menu. Three options are available: None, Single Pen and Dual
Pens.
You can hold the wand the way you would hold a normal pencil or pen, or you can
hold it like a remote control - use in whichever position is most comfortable.
NOTE: If the wand is up close to the screen, you can press its tip against the
projection surface to click and drag. Not recommended for use with fabric
screens.
MDL: IN2128HDa
( Keypad/Remote )
FW: X.XX
Blank Key
Factory Logo
Source Info
Enable
Custom Key
Keypad
LiteBoard™ Wand
◄ None ►
Previous
Download from Www.Somanuals.co5m3. All Manuals Search And Download.
USB Connector
Wand Features
The wand's USB connector is behind a flap on the right side of the wand. The USB
connector is only used for charging the wand's battery - using a USB power
adapter (not included), or a computer.
NOTE: You can use the wand while charging the battery, but after the battery is
charged (battery light turns off), you can unplug the USB cable and continue to use
the wand without a cable.
Sensor
The wand's optical sensor opening is located behind the wand's tip. Don't block
the sensor, and make sure it always has a clear view of the screen.
NOTE: The sensor won't work if you point it at a shadow or away from the
screen.
Reset Button
USB connection
Right mouse button
Left mouse button
Link light
Battery light
The wand has a reset button, behind a small hole on its underside. Under normal
conditions, you should not need to reset the wand. See the Troubleshooting
section below for more information.
Internal Radio
The wand has a built-in wireless transmitter/receiver which it uses to
communicate with the projector.
Buttons and Wand Tip
The wand's buttons are equivalent to the left and right buttons on a mouse. The
wand's tip is also a button, and is equivalent to the left mouse button.
Battery Light
The red battery light shows the status of the wand's built-in battery (see below for
battery information). The battery light will turn on while the wand is charging, and
it will blink if the battery is low (1 hour of wand use left).
Link Light
The blue link light shows the status of the wand's wireless connection to the
projector. The link light will blink twice per second when the wand is attempting
to link to the projector; then it will be on steady after the wand has linked to the
projector.
NOTE: The link light will stay off when the wand is off.
Download from Www.Somanuals.co5m4. All Manuals Search And Download.
Lithium Battery Information
- Make sure your projector is displaying the computer's screen and not some
other source (such as DVD, VCR, etc.). To change the source, press the
Source button on the projector or its remote.
Manufacturer: Shenzhen HYB Battery Co., Ltd.
Model: J233
Rating: 3.7V/800mAh
Caution: Lithium battery is only rechargeable, and not user replaceable. Not user
serviceable.
- Make sure the projector is displaying the same image as the computer's main
or built-in monitor (don't extend your desktop onto multiple monitors). To
correct this:
On Windows XP: Open the Display control panel, click Settings, click the dis-
play that represents the projector, then un-check “Extend my Windows desk-
top...”.
Troubleshooting LiteBoard™
For the most up-to-date information, visit our support site at www.infocus.com/
support
On Windows Vista: Right-click on the desktop, choose Personalize..., click
Display Settings, click the display that represents the projector, then un-check
“Extend the desktop...”.
•
If the wand doesn't work at all, or it works intermittently, try one of these
solutions::
- Press the tip, left or right button on the wand to turn it on.
On both Windows 7 and Windows 8: Right-click on the desktop, choose
Screen Resolution, click the display that represents the projector, and then
choose the “Duplicate Display...” under Multiple Displays.
- If the wand's blue Link light never blinks, then the wand's battery is fully dis-
charged; connect the wand to a USB power adapter (not included) or your
computer.
On Macintosh: Select System Preferences from the Apple Menu, then select
Displays. Click Arrangement, and check “Mirror Displays.”
- Make sure the wand is not pointing at a shadow and make sure its tip is not
in a shadow.
•
If the battery light does not turn on when the wand is being charged, try one
of the following:
- If the room is brightly lit, reduce the room illumination.
- Make sure a USB cable is connected between the wand and either a USB
power adapter (not included), or a USB port on your computer.
- If you're trying to use the computer's mouse at the same time as the wand,
point the wand away from the screen while using the mouse.
- If the wand is connected to a USB power adapter (not included), make sure
the adapter is plugged in to a live electrical outlet. If the wand is connected to
your computer, make sure the computer is powered on.
- Reset the wand: push the end of a paper clip into the reset opening on the
underside of the wand.
•
•
If accurate clicking is difficult, try one of these solutions:
- Hold the wand steadier when clicking.
- If the wand still won't charge, contact InFocus support at: www.infocus.com/
support.
- Use the wand right up against the screen so it's easier to avoid unexpected
movements.
If the mouse pointer is in the wrong place on the screen, or the mouse
pointer's movement is restricted to only part of the screen, try one of these
solutions:
Download from Www.Somanuals.co5m5. All Manuals Search And Download.
Maintenance
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Projector must be off and the lens must be at room temperature.
• Avoid using an excessive amount of cleaner, and don’t apply the cleaner
directly to the lens. Abrasive cleaners, solvents or other harsh chemicals
might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS:
• Turn the projector off and unplug power cord before cleaning any part of
the projector.
• Do not touch or block the projector lens with any objects as this can
damage the projector lens. Scratches, gouges and other lens damage are not
covered by the product warranty.
• Do not open any cover on the projector, except the lamp cover.
• Do not attempt to service this product yourself as opening and removing
covers may expose you to dangerous voltage and other hazards. Refer all
servicing to qualified service personnel.
security
lock
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to the
information that came with the lock for instructions on how to use it.
Download from Www.Somanuals.co5m6. All Manuals Search And Download.
Hg – Lamp contains mercury. Manage in accordance with local disposal
Replacing the projection lamp
The Lamp Hours timer in the Projector Info menu counts the number of hours the
lamp has been in use.
•
NOTE: Be sure to use the InFocus lamp module designed for this projector.
retailer or your dealer. Only genuine InFocus lamps are tested for use in this
projector. Use of non InFocus lamps may cause electrical shock and fire, and
may void the projector warranty. InFocus is not liable for the performance,
safety or certification of any other lamps.
WARNINGS:
•
The projector uses a high-pressure mercury glass lamp. The lamp may fail
prematurely, or it may rupture with a popping sound if jolted, scratched, or
handled while hot. The risk of lamp failure or rupture also increases as the
lamp age increases; please replace the lamp when you see the “Replace Lamp”
message.
•
•
To avoid burns, allow the projector to cool for at least 60 minutes before you
replace the lamp.
Do not touch or block the projector lens with any objects as this can damage
the projector lens. Scratches, gouges and other lens damage are not covered
by the product warranty.
•
•
•
Unplug the power cord before replacing the lamp.
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass surface of the lamp module. Fingerprints can obscure
projection sharpness and may cause the glass to shatter.
•
Be extremely careful when removing the lamp housing. In the unlikely event
that the lamp ruptures, small glass fragments may be generated. The lamp
module is designed to contain most of these fragments, but use caution when
removing it.
•
•
Before replacing a ruptured lamp, clean the lamp compartment and dispose of
cleaning materials. Wash hands after lamp replacement.
When replacing the lamp while the projector is ceiling-mounted, wear
protective eyewear to prevent eye injury.
Download from Www.Somanuals.co5m7. All Manuals Search And Download.
1 Turn off the projector and unplug the power cord.
turn off and unplug
projector
wait 60 minutes
2 Wait 60 minutes to allow the projector to cool thoroughly.
3 Remove the lamp door, located on top of the projector, by removing the
screw on the side of the lamp door, sliding the door forward, and lifting the
lamp door off.
4 Loosen the captive screws that attach the lamp housing to the projector.
NOTE: If the projector is installed on a ceiling mount, be careful not to drop
the lamp module once the captive screws are loosened.
5 Carefully lift the lamp straight up, off of the alignment pins; being careful not to
pinch the lamp connector. Dispose of the lamp in an environmentally proper
manner.
loosen screws
6 Install the new lamp module, aligning the pins properly. Be careful not to pinch
the lamp connector.
7 Tighten the screws. (NOTE: If the pins have not been aligned properly, the
screws will not tighten securely.)
8 Replace the lamp door by (a) aligning the hinges, (b) putting the lamp door
down and (c) locking it back into place.
9 Replace the lamp door screw and tighten securely.
MDL: IN2128HDa
FW: X.XX
( Advanced Menu )
10 Plug in the power cord and press the Power button to turn the projector back
on.
Image
Source Info
Setup
Projector Info
Reset Lamp Hours
Factory Reset
Service Code
Status/Service
11 To reset the lamp hour timer, navigate to the Advanced Menu > Status/Service
menu and select Reset Lamp Hours....
Basic Menu
Download from Www.Somanuals.co5m8. All Manuals Search And Download.
D
E
F
Numerics
A
B
G
C
H
Connecting
I
K
Download from Www.Somanuals.co5m9. All Manuals Search And Download.
L
R
S
T
M
N
O
P
Projector
U
Download from Www.Somanuals.co6m0. All Manuals Search And Download.
V
W
Z
Download from Www.Somanuals.co6m1. All Manuals Search And Download.
|