I N S T A L L A T I O N I N S T R U C T I O N S
Short Throw Wall Mount
PRJ-WALLKIT-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PRJ-WALLKIT-13
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Marcar con lápiz
Stiftmarkierung
Marquage au crayon
Segno a matita
Marcar com lápis
留め具を締める
上紧紧固件
鉛筆
で印を付ける
Befestigungsteil festziehen
Serrez les fixations
Serrare il fissaggio
Apertar fixador
铅笔标记
旋緊扣件
鉛筆標記
패스너 조이기
ดงึ สายรัดใหแ้ น่น
연필 표시
ดนิ สอทําเครอื่ งหมาย
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desserrez les fixations
Allentare il fissaggio
Soltar fixador
Perforar
留め具を緩める
松开紧固件
ドリルで穴を開ける
Bohrloch
钻孔
Percez un trou
Praticare un foro
Perfurar
鬆開扣件
鑽孔
패스너 풀기
드릴 구멍
เจาะรู
คลายสายรดั ใหห้ ลวม
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
プラスドライバー
十字螺丝刀
調節する
调节
Kreuzschlitzschraubendreher
Tournevis à pointe cruciforme
Cacciavite a stella
Einstellen
Ajuster
十字螺絲起子
調整
Regolare
Regular
십자 나사드라이버
ไขควงปากแฉก
조정
ปรับ
Chave de fendas Phillips
Open-Ended Wrench
Llave de boca
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Clé à tête hexagonale
Chiave esagonale
スパナ
六角レンチ
六头扳手
Gabelschlüssel
开口扳手
雙頭扳手
양입 렌치
ประแจปากตาย
Clé à fourche
六角扳手
Chiave a punte aperte
Chave de porcas aberta
육각 렌치
Chave sextavada
ประแจหวั หกเหลยี่ ม
By Hand
A mano
Von Hand
À la main
A mano
À mão
Socket Wrench
Llave de cubo
Steckschlüssel
Clé à douilles
手で行う
手动
ソケットレンチ
套筒扳手
以手操作
손으로
ดว้ ยมอื
套筒扳手
Chiave a brugola
Chave de tubos
소켓 렌치
ประแจกระบอก
Hammer
Martillo
Measure
Medir
ハンマー
锤子
メジャー
测量
Hammer
Marteau
Martello
Martelo
Messen
Mesurer
Misura
Medir
鐵鎚
測量
망치
줄자
คอ้ น
วัด
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRJ-WALLKIT-13
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
Hardware required, NOT INCLUDED:
Steel Stud Install
•
•
4 - Toggler® 1/4-20 (BB) Snap-Toggle
4 - Grade 2 or better 1/4-20 x 1-3/4" Phillips
pan head screws
5/32"
(included)
1/2"
•
4 - Grade 2 or better 1/4" washer
Concrete Install
•
4 - Fischer UX 10 x 60 anchors [P/N 077871],
OR
•
Toggler A8/AF8 anchors
1/2" - steel stud
3/8" / 5/16" - concrete
7/32" - wood stud
Wood Stud Install and Concrete Install
•
4 - Grade 2 or better 5/16 x 2-1/2" hex head
lag screws
•
4 - Grade 2 or better 5/16" washers
PARTS
A (1)
[Short throw
projector arm]
B (1)
[Wall plate]
E (1)
[Wall cover - right]
F (1)
[Wall cover - left]
C (1)
[Arm adjust plate]
D (1)
[End cap]
H (1) [Hardware kit]
HB (4)
HA (4)
10-24 x 5/8"
M4 x 8mm
[one not used]
HC (1)
5/32"
G (2)
[Dual stud bracket]
HF (4)
5/16"
HE (1)
1/4-20 x 1-1/4"
HD (2)
1/4-20 x 3/4"
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PRJ-WALLKIT-13
Site Requirements
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! The figure below identifies the minimum requirements for installation of mount onto a steel stud
structure. If the structure or its components do not meet these requirements contact the mount manufacturer for specific
instructions before attempting installation. It should also be noted that no other equipment should be mounted to the same stud.
16" (on center) Studs
Short Throw Mount Installation Location
(Centered over two studs, or over
one stud)
If back side of wall is unfinished, drywall must be installed
to a minimum of one stud left and right of the studs
being used to install the mount. Drywall must be
secured to studs using screws spaced a maximum
of 10" apart along stud.
There must be a minimum of
1-7/8" (48mm) clearance
inside wall
FRONT
Drywall
**1/2" minimum
Drywall Thickness
(Both Sides of Stud)
**See hazard statement
on page 2!
Steel Stud (2 x 4 / 25ga minimum)
Stud type and structural strength must conform to the North American
Specification for the Design of Cold-Formed Steel Structural Members.
[362, 125 18, C-Shape, S - Stud Section]
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PRJ-WALLKIT-13
Installation Instructions
ASSEMBLY AND INSTALLATION
The PRJ-WALLKIT-13 short throw projector mount is designed
to be mounted to solid concrete, hollow concrete block, 2" x 4"
wood studs (16" on center), or steel studs (16" on center).
x 4 (dual stud)
1
2
Assembling Wall Plate to Brackets
x 2 (single stud)
IMPORTANT ! : This step must be taken for BOTH single
AND dual stud installations!
(G)
1. Attach wall plate (B) to two dual stud brackets (G) using four
5/16" lock nuts (HF). (See Figure 1)
(G)
1
(HF) x 4
3
anchors
4
fasteners
(Single stud fasteners/anchors shown in gray)
Figure 2
NOTE: Proceed to Installing Short Throw Projector Arm to
Bracket section to continue installation.
(B)
Figure 1
NOTE: Proceed to the Concrete or Concrete Block, Wood
Studs or Steel Studs section, as appropriate for
installation.
Concrete or Concrete Block
1. Using wall plate/bracket assembly, mark four mounting
holes (dual stud), or two mounting holes (single stud) in wall
plate. (See Figure 2)
2. Drill one 3/8" hole at one of the marked locations in wall.
(See Figure 2)
3. Install either one Fischer UX 10 x 60 anchor [Part number
077871] (not included) or one Hilti HUD-L 10x70 anchor
(not included) into one of the drilled holes. (See Figure 2)
4. Install one Grade 2 or better 5/16 x 2-1/2" hex head lag screw
(not included) through one Grade 2 or better 5/16" washer
(not included), one mounting hole in wall bracket and into one
Fischer or Hilti anchor (not included). (See Figure 2)
5. Level wall bracket using attached bubble level.
6. Make any necessary corrections to remaining mounting
hole marking(s).
7. Repeat Steps 2 through 4 for remaining mounting hole(s).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PRJ-WALLKIT-13
Wood Studs
Steel Studs
1. Using a stud finder and wall plate/bracket assembly, mark
four preliminary mounting holes (dual stud) over center of
wood studs, or two mounting holes (single stud) in wall
plate. (See Figure 3)
IMPORTANT ! : See Site Requirements section before
proceeding with Steel Studs installation to ensure installation
site meets requirements! The drywall must have a minimum
thickness of 1/2"!
1. Using a stud finder and wall plate/bracket assembly, mark
four preliminary mounting holes over center of steel studs,
or two mounting holes (single stud) in wall plate. (See
Figure 4)
2. Drill one 7/32" hole at marked location in wall. (See Figure 3)
3. Install one Grade 2 or better 5/16 x 2-1/2" hex head lag
screw (not included) through one Grade 2 or better 5/16"
washer (not included), hole in wall bracket and into drilled
hole. (See Figure 3)
2. Drill one 1/2" hole at marked location on wall. (See Figure 4)
(Dual stud)
(Dual stud)
x 4
3
(G)
1
x 4
2
1
2
(Single stud)
x 4
(Single stud)
1
x 2
2
1
2
x 2
x 2
3
Figure 4
3. Hold metal channel on Toggler® 1/4-20 (BB) Snap-Toggle
(not included) flat alongside plastic straps and slide channel
through hole. (See Figure 5)
x 2
3
Figure 3
Drywall
4. Level wall bracket using attached bubble level.
Plastic Straps
3
5. Make any necessary corrections to remaining mounting
hole marking(s).
6. Repeat Steps 2 and 3 for remaining mounting hole(s).
NOTE: Proceed to Installing Short Throw Projector Arm to
Bracket section to continue installation.
x 4
Figure 5
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PRJ-WALLKIT-13
Installation Instructions
4. Holding plastic straps on anchor, pull anchor away from wall
until channel rests flush behind wall making sure anchor
channel is positioned vertically on stud. (See Figure 6)
Steel
stud
Drywall
5. Slide plastic cap on anchor towards wall until flange of cap
is flush with wall. (See Figure 6)
x 4
x 4
10
Steel Stud
Drywall
Plastic Cap
4
5
(G)
Anchor Metal Channel
anchor x 4
(side view)
Anchor Metal Channel
(side view)
Figure 6
Figure 8
6. Snap off plastic straps on anchor at wall by pushing side to
side, snapping off straps level with flange of plastic cap.
(See Figure 7)
9. Level wall bracket using attached bubble level.
10. Make any necessary corrections to remaining mounting
hole marking(s).
Steel Stud
Drywall
Plastic Cap
11. Repeat Steps 2 through 8 for remaining mounting hole(s).
Adjusting Projector Mount
6
Lower projector mount [attached to short throw projector arm
(A)] to lowest position. (See Figure 9)
1. Loosen two screws (one on each side of projector mount).
(See Figure 9)
2. Turn the button head cap screw on top of mount
counterclockwise to lower the mount. (See Figure 9)
Plastic Straps
3. Loosen four hex head bolts. (See Figure 9)
(side view)
Anchor Metal Channel
Figure 7
7. Place wall bracket over anchor and align mounting hole in
wall bracket with hole in anchor. (See Figure 8)
8. Insert Grade 2 or better 1/4-20 x 1-3/4" Phillips pan head
screw (not included) through Grade 2 or better 1/4" washer
(not included), corresponding mounting hole on wall bracket
and into Snap-Toggle (not included) and tighten until flush
against mount. DO NOT overtighten! (See Figure 8)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PRJ-WALLKIT-13
(B)
Wall plate hook
(A)
x 1
2
2
x 4
3
(G)
Projector arm slots
Figure 11
3. Fasten short throw arm (A) to wall plate (B) using two
1/4-20 x 3/4" button head cap screws (HD). (See Figure 12)
x 2
1
(HD) x 2
3
Figure 9
Installing Short Throw Projector Arm to Bracket
1. Attach arm adjust plate (C) to wall plate ensuring that adjust
plate tabs fit into notches on wall plate. Insert and slightly
tighten one 1/4-20 x 1-1/4" button head cap screw (HE). (See
Figure 10)
(G)
(C)
Figure 12
(HE) x 1
1
Figure 10
2. Lift short throw projector arm (A) up to wall plate (B) and
place projector arm slots over wall plate hooks. (See
Figure 11)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PRJ-WALLKIT-13
Installation Instructions
Projector Installation
x 4
6
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the weight of the
projector does not exceed 25 lbs (11.3 kg).
1. Insert and slightly tighten two M4 x 8mm Phillips pan head
screws (HA) into the projector threaded inserts. (See
Figure 13)
(projector example
only)
(HA) x 2
1
Back of
projector
Figure 15
Leveling the Projector Arm
Tighten the button head cap screw on the arm adjustment plate
(C) to level the projector arm. (See Figure 16)
Figure 13
2. Raise the projector up to the projector arm and slide two
screws into slots on the projector arm. (See Figure 14)
3. Add one remaining M4 x 8mm Phillips pan head screw (HA)
through the projector arm and into the projector. (See
Figure 14)
x 1
4. Tighten all three fasteners.
5. Slide projector along short throw projector arm until image
is the correct size on screen.
(HA) x 1
3
Figure 16
Projector
2
Figure 14
6. Tighten four hex head bolts, making sure image is square
with wall. (See Figure 15)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PRJ-WALLKIT-13
Adjustments
Height Adjustment
2
1. Loosen two Phillips screws (one on left, one on right). (See
Figure 17)
x 1
OR
(raise)
(lower)
2. Turn the button head cap screw on top of mount clockwise
to raise the mount (counterclockwise to lower the mount).
(See Figure 17)
3. Tighten two Phillips screws. (See Figure 17)
Pitch Adjustment
NOTE: Use a level to make this process easier.
1
4. Loosen two Phillips screws (one on right, one on left). (See
Figure 17)
x 2
3
5. Tip up or down, as required.
6. Tighten two Phillips screws. (See Figure 17)
Roll Adjustment
NOTE: Use a level to make this process easier.
7. Loosen one Phillips screw. (See Figure 17)
8. Adjust horizontal tilt, as required.
9. Tighten one Phillips screw. (See Figure 17)
Side-to-Side Adjustment
10. Loosen four Phillips screws (two on front, two on back).
(See Figure 17)
11. Adjust side-to-side, as required.
12. Tighten four Phillips screws. (See Figure 17)
x 1
x 2
7
8
9
4
5
6
x 4
10 11 12
Figure 17
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PRJ-WALLKIT-13
Installation Instructions
3. Add end cap (D) to end of short throw projector arm. (See
Figure 20)
Cable Management (Optional)
1. Route cables/cords from projector through opening on
projector arm and route to wall. (See Figure 18)
2. Guide cables/cords from wall end of projector arm upward
or downward through slots in wall plate. (See Figure 18)
3
(D) x 1
2
2
(projector not shown)
1
Figure 20
Projector
Projector arm
opening
Figure 18
Add Plastic Covers
1. Add right and left plastic covers (E and F) over brackets.
(See Figure 19)
2. Fasten covers using four 10-24 x 5/8" Phillips cap head
screws (HB). (See Figure 19)
(projector not shown)
(HB) x 2
2
(F)
1
(E)
1
(A)
(HB) x 2
2
Figure 19
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PRJ-WALLKIT-13
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PRJ-WALLKIT-13
Installation Instructions
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
PRJ-WALLKIT-13
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
InFocus Corporation
13190 SW 68th Parkway, Ste 200
Portland, OR 97223
8800-002462 Rev00
©2013 InFocus Corporation
09/13
Download from Www.Somanuals.com. All Manuals Search And Download.
|