Download from Www.Somanuals.com. All Manuals Search And Download.
11
25
HDMI connection
Download from Www.Somanuals.com. All Manuals Search And Download.
2
•
•
•
Refer all service to qualified service personnel. Servicing your own projector
can be dangerous to you and will void the warranty.
Important Operating Considerations for Safety
•
•
•
Refer to this guide for proper startup and shutdown procedures.
Follow all warnings and cautions in this manual and on the projector.
Only use replacement parts specified by InFocus. Unauthorized substitutions
may result in fire, electrical shock, or injury, and may void the warranty
Place the projector in a horizontal position no greater than 15 degrees off
axis.
Only genuine InFocus lamps are tested for use in this projector. Use of non
InFocus lamps may cause electrical shock and fire, and may void the projector
warranty.
•
•
Locate the projector at least 4' (1.2m) away from any heating or cooling
vents.
•
•
Hg – Lamp contains mercury. Manage in accordance with local
Do not block ventilation openings. Locate the projector in a well-ventilated
area without obstructions to intake or exhaust vents. Do not place the
projector on a tablecloth or other soft covering that may block the vents.
The projector uses a high-pressure mercury glass lamp. The lamp may fail
prematurely, or it may rupture with a popping sound if jolted, scratched, or
handled while hot. The risk of lamp failure or rupture also increases as the
lamp age increases; please replace the lamp when you see the “Replace Lamp”
message.
•
•
Do not place the projector in direct sunlight, humid, greasy or dusty places or
in places where the projector may come into contact with smoke or steam.
Do not touch or block the projector lens with any objects as this can damage
the projector lens. Scratches, gouges and other lens damage are not covered
by the product warranty.
•
In the unlikely event of a lamp rupture, particles may exit through the
projector vents. Please keep people, food, and drinks at least 3’ (1m) away
from all projector vents. For ceiling applications, keep people, food and drinks
out of the "keep out" area under and around the projector, as indicated by
the illustration.
•
•
•
•
Do not look directly into the lens while the projector is being used.
Do not drop the projector.
Do not spill liquid on the projector. Spilled liquid may damage the projector.
Use the power cord provided. Connect the power cord to a receptacle with
a protective safety (earth) ground terminal. A surge-protected power strip is
recommended.
•
•
•
•
Do not overload wall outlets.
When disconnecting the power cord, hold the plug, not the cord.
Wash hands after handling the cables supplied with this product.
m
5
8
.
/ 1
’
/ 2
.
4
m
’
5
Follow these instructions to help ensure image quality and lamp life over the life of
the projector. Failure to follow these instructions may affect the warranty. For
complete details of the warranty, see the Warranty Booklet.
The projector remote control uses batteries. Make sure the batteries’
polarity (+/-) is aligned correctly. Dispose of used batteries in accordance
with local disposal laws.
•
•
Use an InFocus approved ceiling mount kit for proper fitting, ventilation and
installation. The warranty does not cover any damage caused by use of non-
approved ceiling mount kits or by installing in an improper location.
When the projector is ceiling mounted, wear protective eyewear to prevent
eye injury before opening lamp door.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
IN112a/IN114a/IN116a/IN112aT/IN114aT/IN114STa
Introduction
keypad
Your new digital projector is simple to connect, easy to use, and straightforward
to maintain. It is a versatile projector that is flexible enough for business
presentations and home video viewing too. IN112a/IN112aT has native SVGA 800
x 600 resolution, IN114a/IN114aT/IN114STa has native XGA 1024 x 768
resolution, IN116a has native WXGA 1280 x 800 resolution, and IN118HDa/
IN118HDSTa has native 1080p 1920 x 1080 resolution. It is compatible with a
wide variety of computers and video devices.
lamp cover
zoom
remote control
receiver (IR)
security bar
Product specifications
lens
To read the latest specifications on your multimedia projector, be sure to visit our
IN118HDa
keypad
lamp cover
zoom
Accessories
The standard accessories that came with your projector are listed in the included
Quick Start Guide. Optional accessories can be found on our website at
www.infocus.com/support or at your retailer or dealer.
Online registration
remote control
receiver (IR)
security bar
your warranty and receive product updates, announcements, and registration
incentives.
lens
IN118HDSTa
keypad
focus
lamp cover
zoom
connector
panel
remote control
receiver (IR)
power cord
connector
security bar
lens
Download from Www.Somanuals.com. All Manuals Search And Download.
4
IN112a/IN114a/IN116a/IN114STa/IN118HDa/IN118HDSTa
Connector panel
S-video
The projector provides both computer and video connection options, including:
RS 232
USB
•
•
•
•
•
•
•
•
•
VGA computer (2)
HDMI
computer
audio in/out
Composite video (model dependent)
HDMI (model dependent)
S-video (model dependent)
USB connector for firmware upgrades, mouse control and Screen Save mode.
Monitor out, for VGA pass through to an external monitor.
Audio inputs for video and computer.
Audio output to external speakers.
RS-232 serial control. Command control codes are on our support website at
NOTE: IN112aT/IN114aT do not have S-video, composite video or HDMI
connectors.
composite video
security lock
monitor
out
IN112aT/IN114aT
audio in/out
RS 232
USB
computer
security lock
monitor
out
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Positioning the projector
To determine where to position the projector, consider the size and shape of your
screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Here are some general guidelines:
Model
IN112a
IN112aT
IN114a
IN114aT
Minimum Distance to Screen
45.3"/1.2m
Offset
Offset for 60in. Image
9"/22.9cm
15%+-5%
15%+-5%
15%+-5%
15%+-5%
45.3"/1.2m
9"/22.9cm
45.3"/1.2m
9"/22.9cm
•
Position the projector on a flat surface at a right angle to the screen. IN112a/
IN112aT and IN114a/IN114aT must be at least 45.3” (1.2m) from the projection
screen, IN116a must be at least 55.4” (1.4m) from the projection screen,
IN114STa must be at least 15” (0.4m) from the projection screen, IN118HDa
must be at least 37.5” (1.0m) from the projection screen, and IN118HDSTa must
be at least 30.6” (0.78m) from the projection screen.
45.3"/1.2m
9"/22.9cm
IN114STa
IN116a
15"/0.4m
55.4"/1.4m
37.5"/1.0m
15%+-5%
13%+-5%
17%+-5%
9"/22.9cm
7.8"/19.8cm
5"/12.7cm
IN118HDa
•
If you are installing the projector on the ceiling, we strongly recommend using
InFocus approved ceiling mounts for proper fitting, ventilation and installation.
Refer to the installation guide that comes with the InFocus Ceiling Mount Kit (p/n
PRJ-MNT-UNIV) for more information. The warranty does not cover any damage
caused by use of non-approved ceiling mount kits or by installing in an improper
recommend using an InFocus authorized ceiling mount.
IN118HDSTa
72 inches
high image
Projection angle
•
Position the projector the desired distance from the screen. The distance from
the lens of the projector to the screen and the video format determine the size of
the projected image.
bottom of image 9
inches above center
of lens
lens center
IN112a/IN112aT/IN114a/IN114aT/IN114STa/IN116a/IN118HDa
60 inches
high image
Projection angle
Model
Minimum Distance to Screen
30.6"/0.78m
Offset
Offset for 72in. Image
6”/15.2cm
IN118HDSTa
12%+-5%
bottom of image 9
inches above center
lens center
of lens
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Table 4: IN118HDa (1080p) Screen size
Throw Ratio = 1.5 to 1.8
Table 1: IN112a/IN112aT (SVGA)/IN114a/IN114aT(XGA) Screen size
Throw Ratio = 1.9 to 2.2
Size of the
Projected Image
Width
Distance to screen
Diagonal Screen
Size (inches/m)
Size of the
Projected Image
Width
Distance to screen
Minimum distance
(inches/m)
Maximum distance
(inches/m)
Diagonal Screen
Size (inches/m)
(inches/m)
Minimum distance
(inches/m)
Maximum distance
(inches/m)
40”/1.0m
60”/1.5m
80”/2.0m
100”/2.5m
150”/3.8m
35”/0.9m
52”/1.3m
70”/1.8m
87”/2.2m
131”/3.3m
52.3”/1.3m
78.4”/2.0m
104.6”/2.7m
130.7”/3.3m
196.1”/5.0m
62.7”/1.6m
94.1”/2.4m
125.5”/3.2m
156.9”/4.0m
235.4”/6.0m
(inches/m)
40”/1.0m
60”/1.5m
80”/2.0m
100”/2.5m
150”/3.8m
32”/0.8m
48”/1.2m
64”/1.6m
80”/2.0m
120”/3.0m
62”/1.6m
94”/2.4m
125”/3.2m
156”/4.0m
234”/5.9m
69”/1.7m
103”/2.6m
137”/3.5m
172”/4.4m
257”/6.5m
Table 5: IN118HDSTa (1080p) Screen size
Throw Ratio = 0.52
Table 2: IN114STa (XGA) Screen size
Throw Ratio = 0.61
Size of the
Diagonal Screen
Size (inches/m)
Projected Image
Width
(inches/m)
Distance to screen (inches/m)
Size of the
Projected Image
Width
Diagonal Screen
Size (inches/m)
Distance to screen (inches/m)
72”/1.8m
80”/2.0m
95”/2.4m
100”/2.5m
62”/1.6m
70”/1.8m
83”/2.1m
87”/2.2m
31”/0.8m
34”/0.9m
41”/1.0m
43”/1.1m
(inches/m)
40”/1.0m
60”/1.5m
80”/2.0m
100”/2.5m
150”/3.8m
32”/0.8m
48”/1.2m
64”/1.6m
80”/2.0m
120”/3.0m
20”/0.5m
30”/0.8m
40”/1.0m
50”/1.3m
75”/1.9m
Table 3: IN116a (WXGA) Screen size
Throw Ratio = 1.5 to 1.8
Size of the
Projected Image
Width
Distance to screen
Diagonal Screen
Size (inches/m)
Minimum distance
(inches/m)
Maximum distance
(inches/m)
(inches/m)
45”/1.1m
60”/1.5m
80”/2.0m
100”/2.5m
150”/3.8m
38”/1.0m
51”/1.3m
68”/1.7m
85”/2.2m
128”/3.2m
55.4”/1.4m
74.5”/1.9m
100.0”/2.5m
125.5”/3.2m
189.2”/4.8m
69.3”/1.8m
92.9”/2.4m
124.4”/3.2m
155.8”/4.0m
234.6”/6.0m
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Connecting a computer source
connect VGA cable
VGA connection
Connect one end of the provided computer cable to th Computer 1/Computer 2
connector on the projector and the other to the VGA connector on your
computer. If you are using a desktop computer, you will need to disconnect the
monitor cable from the computer’s video port first.
connect HDMI
HDMI connection
HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI
provides an interface between sources, such as set-top boxes, DVD players, and
receivers and your projector. Plug an HDMI cable into the video-out connector on
the video device and into the HDMI connector on the projector.
NOTE: The IN112aT/IN114aT do not have an HDMI connector.
connect power
Connecting power
Connect the black power cord to the Power connector on the rear of the
projector and to your electrical outlet. If the Power Saving Mode feature is off, the
Mode feature is on, the Power LED is steady blue. By default, this feature is off.
shipped with the projector.
connect audio cable
Optional computer connections
To get sound from the projector, connect an audio cable (optional cable, not
included) to your computer and to th Audio 1/Audio 2 connector on the
projector. You may also need an adapter.
If you are using a desktop computer and want to see the image on your computer
screen as well as on the projection screen, connect to the desktop’s computer
cable to Computer 1 and the desktop’s monitor cable to the Monitor Out
connector on the projector.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Displaying an image
Press the Power button.
press Power button
The Power LED lights blue, and the fans start to run. When the lamp comes on,
the start up screen displays. It can take up to a minute for the image to achieve full
brightness. Note: When the feature, AC Power On, is enabled, the projector
automatically turns on when power is connected. This allows control of ceiling
mounted projectors with a wall power switch.
turn on computer or
video device
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the Source
button on the projector’s keypad or remote.
If you are using a VGA cable to connect your computer to the projector:
If using a laptop, make sure its external video port is active.
activate laptop’s external port
monitor key or
LCD/CRT key
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/LCD key
turns the external display on and off. Locate a function key labeled CRT/LCD or a
function key with a monitor symbol. Press FN and the labeled function key
simultaneously.
FN key
Refer to your laptop's documentation for more information about your laptop's
key combination.
No laptop image? Try pressing the Auto Image button on the remote. Get
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Adjusting the image
adjust height
If necessary, adjust the height of the projector by rotating the elevator foot to
extend the foot.
elevator
foot
If necessary, rotate the leveling foot located at the rear of the projector.
Avoid placing your hands near the hot exhaust vent at the front of the projector.
adjust distance
Position the projector the desired distance from the screen at a 90 degree angle to
the screen.
Adjust the zoom or focus.
adjust zoom and focus
If the image is not square, first make sure that the projector is perpendicular to the
screen. If the image is larger or smaller on the top or bottom edge of the screen,
adjust keystone
press the top Keystone button
to reduce the upper part of the image, and
to reduce the lower part.
press the bottom Keystone button
If the left or right side of the screen is larger or smaller the other, you can turn the
projector to the left or to the right a few degrees to square the image.
MDL: IN112a
FW: 0.14
( Basic Menu )
Aspect Ratio
Auto Image
Brightness
Contrast
these menu adjustments.
adjust Basic Menu
◄ Auto
Execute
50
50
Off
0
►
Auto Keystone
Keystone
Presets
Presentation
Sharpness
Volume
Ceiling Mount
16
16
Off
Advanced Menu
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
VGA connection
Connecting a video device
If your video device has a 15-pin VGA output, plug one end of the included
computer cable into the VGA connector on your video source. This connector
may be labeled “To Monitor” on the video source. Plug the computer cable into
either the Computer 1 or Computer 2 connector on the projector.
You can connect video devices such as VCRs, DVD players, camcorders, digital
cameras, video game consoles, HDTV receivers, and TV tuners to the projector.
You can connect the audio directly to the projector to get sound from the built-in
speaker, or you can bypass the projector’s audio system and connect the audio
directly from your source to a stereo or home theater system.
Component video connection
You can connect the projector to most video devices that can output video. You
cannot directly connect the coaxial cable that enters your house from a cable or
satellite company, the signal must pass through a tuner first. Examples of tuners
are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes.
Basically, any device that can change channels is considered a tuner.
If your HD video device has component connectors, an optional Component to
VGA adapter can be used. Plug the component cable into the video device. Plug
the other end of the component cable into the adapter and plug the adapter into
the Computer 1 or Computer 2 connector.
Before connecting your projector, you should decide which aspect ratio you want
to use. The projector’s Aspect Ratio setting is accessed through the Resize button
information.
S-video connection
Plug the S-video cable’s connector into the video-out connector on the video
device. Plug the other connector into the S-Video connector on the projector.
NOTE: The IN112aT/IN114aT do not have an S-video connector.
Video device connections
No video cables are provided with the projector. You can order cables from
InFocus or provide your own.
Audio
For audio, connect a 3.5mm stereo cable to the Audio 1/Audio 2 connector on the
projector and to your source. If your source uses RCA audio connectors, a Y-
cable or adapter may be used. (Note: A separate audio connection is not required
for HDMI source inputs.)
HDMI connection
HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI
provides an interface between sources, such as set-top boxes, DVD players, and
receivers and your projector. Plug an HDMI cable into the video-out connector on
the video device and into the HDMI connector on the projector.
NOTE: The IN112aT/IN114aT do not have an HDMI connector.
Composite video connection
Plug the composite video cable’s yellow connector into the video-out connector
on the video device. Plug the other yellow connector into the yellow Video
connector on the projector.
NOTE: The IN112aT/IN114aT do not have a composite connector.
Download from Www.Somanuals.co1m1. All Manuals Search And Download.
The Status Indicator Lights on top of the projector indicates the state of the
projector and can help you troubleshoot.
Shutting down the projector
Auto Off Time
The projector also has an Auto Off Time feature that automatically turns the
projector off after no active sources are detected and no user interaction with the
projector is performed for 30 minutes. By default, this feature is off. You can
Table 6: Status Indicator Lights
Status Indicator Light
Meaning
Turning off the projector
POWER: Solid Blue
TEMP: Off
LAMP: Off
1. If the Power Saving Mode feature is
on, the projector is plugged in.
2. The projector is on and initialized.
3. The projector is in normal operation.
To turn the projector off, press the Power button on the remote or keypad. The
lamp turns off and the Power LED blinks blue for 30 seconds while the fans
continue to run to cool the lamp. If the Power Saving Mode feature is on and when
the lamp has cooled, the LED lights blue and the fans stop. If the Power Saving
Mode feature is off and when the lamp has cooled, the LED blinks blue and the fans
stop. Unplug the power cable to completely power off the projector.
POWER: Blinking Blue
TEMP: Off
1. If the Power Saving Mode is off, the
projector is plugged in.
LAMP: Off
2. The projector is powering down and
the fans are cooling the projector.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it does
not, troubleshoot the setup.
POWER: Blinking blue
TEMP: Blinking red
LAMP: Blinking red
The projector fan(s) are not operating
correctly and the projector has been
shut down.
The lamp failed to ignite.
Contact Technical Support if the
problem persists. Visit
service.
POWER: Solid blue
TEMP: Blinking red
LAMP: Blinking red
POWER: Solid blue
TEMP: Blinking red
LAMP: Blinking red
The lamp has reached its end of life and
must be replaced. The lamp will
continue to operate untils it fails.
Contact Technical Support. Repair may
be needed.
POWER: Solid blue
TEMP: Blinking red
LAMP: Off
1. The projector is overheating and the
lamp will be shut off. The fans will
continue to run.
2. The projector will not turn back on
until the cooling process is complete.
Download from Www.Somanuals.co1m2. All Manuals Search And Download.
Problem
Solution
Result
No start up screen
Correct image
Plug power cord into the projector
press the Power button
Startup
Screen
Press the SOURCE button
activate laptop’s external port
Computer image projected
Only start up screen appears
Startup
Screen
A
A
Restart laptop
A
Download from Www.Somanuals.co1m3. All Manuals Search And Download.
Problem
Solution
Result
Press the Auto Image button on remote
Computer image projected
No computer image, just the words “Signal out of
range”
Adjust computer refresh rate (Windows 7: Control
Panel > Display > Screen Resolution > Advanced
Settings > Adapter tab). Varies per operating system.
A
Signal out of
the range
A
A
You may also need to set a different resolution on your
computer, as shown in the following problem, “image
fuzzy or cropped”
Only my laptop’s background appears, not the
Desktop icons
Change the Multiple Display setting to "Duplicate these
displays" (Windows 7: Control Panel > Display > Screen
Resolution). Varies per operating system.
Background and Desktop projected
A
A
A
A
Download from Www.Somanuals.co1m4. All Manuals Search And Download.
Problem
Solution
Result
Change the computer's "Resolution" setting to match
the projector's resolution (Windows 7: Control Panel >
Display > Screen Resolution). Varies per operating
system.
Image fuzzy or cropped
Image clear and not cropped
A
A
A
Correct image
Move projector, adjust height
Image not centered on screen
MDL: IN112a
( PC )
FW: 0.14
Force Wide
Off
24
Off
0
Phase
Prevent PC Screen Saver
Sync Threshold
Tracking
Adjust horizontal or
vertical position in
Advanced Menu >
Image > PC... menu
0
Horz Position
Vert Position
0
7
Previous
Download from Www.Somanuals.co1m5. All Manuals Search And Download.
Problem
Solution
Result
Image not square
Adjust Keystone on keypad
Square image
Adjust Sharpness in the Basic Menu
Image not sharp
Correct image
MDL: IN112a
FW: 0.14
( Basic Menu )
Aspect Ratio
Auto Image
Brightness
Contrast
Auto
Execute
50
50
Auto Keystone
Keystone
Off
0
Presets
Presentation
Sharpness
Volume
Ceiling Mount
16
16
Off
Advanced Menu
Correct image
Change aspect ratio to 4:3 or 16:9 in Basic Menu >
Aspect Ratio menu
Image does not fit 4:3 or 16:9 screen
MDL: IN112a
( Basic Menu )
Aspect Ratio
Auto Image
Brightness
Contrast
FW: 0.14
◄ Auto ►
Execute
50
50
Auto Keystone
Keystone
Off
0
Presets
Presentation
Sharpness
Volume
Ceiling Mount
16
16
Off
Advanced Menu
Download from Www.Somanuals.co1m6. All Manuals Search And Download.
Problem
Solution
Result
Turn off Ceiling Mount in Basic menu
Correct image
Image upside down
MDL: IN112a
(
Basic Menu
)
FW: 0.14
Aspect Ratio
Auto Image
Brightness
Contrast
Auto
Execute
50
50
A
A
Auto Keystone
Keystone
Presets
Sharpness
Volume
Ceiling Mount
Off
0
Presentation
16
16
Off
Advanced Menu
Turn off Rear Project in Advanced Menu > Setup >
Image Setup... menu
Correct image
Image reversed left to right
MDL: IN112a
( Image Setup )
Digital Zoom
Horz Shift
Vert Shift
Magnify Level
Horz Shift
Vert Shift
Ceiling Mount
Rear Project
FW: 0.14
100
50
50
0
50
50
Off
Off
Previous
Adjust the items in the Advanced Menu > Image >
Color... menu
Projected colors don’t match source
Correct image
MDL: IN112a
( Color )
FW: 0.14
Color
100
50
50
50
50
Red Gain
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset
Color Space
Color Temp
Gamma
50
50
COLOR
COLOR
Auto
Cool
CRT
100
100
Tint
White Intensity
Previous
Download from Www.Somanuals.co1m7. All Manuals Search And Download.
Problem
Solution
Result
Turn off the internal LCD display on your laptop
The video embedded in my PowerPoint presentation
does not play on the screen
Embedded video plays correctly
A
A
B
A
B
Make sure vents aren’t blocked, turn off the projector
and allow it to cool for one minute
Lamp turns on
Lamp won’t turn on, the projector is overheating
Startup
Screen
Overheating
indicator
Download from Www.Somanuals.co1m8. All Manuals Search And Download.
Problem
Solution
Result
Lamp turns on
“Replace lamp” message appears at startup, lamp
won’t turn on
lamp door
Startup
Screen
replace lamp
Still need assistance?
See the Quick Start Guide for support contact information.
This product is backed by a limited warranty. An extended warranty plan may be
purchased from your dealer. When sending the projector in for repair, we
recommend shipping the unit in its original packing material, or having a
professional packaging company pack the unit. Please insure your shipment for its
full value.
Download from Www.Somanuals.co1m9. All Manuals Search And Download.
•
•
•
•
•
•
•
•
•
•
•
Auto Image button to resynch the projector to the source.
Help button to get help with connecting sources and improving the picture.
ESC button to go back to previous OSD menu.
Using the remote control
The remote uses two (2) AAA batteries (not provided). They are easily installed
by removing the cover from the remote’s back, aligning the + and - ends of the
batteries, sliding them into place, and then replacing the cover.
PC button to cycle through the Computer sources.
Caution:
Video button to cycle through Composite/S-Video/HDMI input sources.
Keystone buttons adjust the squareness of the image
•
When replacing the remote batteries, be aware that using batteries other
than AAA batteries may risk severe damage to the remote. When disposing
of the batteries, be sure to do so in an enviromentally proper manner.
Magnify buttons magnify and reduce the projected picture size.
Freeze button to pause the projected image.
•
•
•
•
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
Overscan button remove noise around the video image.
AV Mute button blanks the projected image and mutes audio.
Ensure the batteries' polarity (+/-) is aligned correctly.
Troubleshooting the remote
Do not mix new and old batteries together, or mix different types of batter-
ies together.
•
Make sure the batteries are installed in the proper orientation and are not
dead.
•
•
Replace the batteries as soon as they run out.
•
Make sure you’re pointing the remote at the projector or the screen, not the
computer, and are within the remote range of 15 feet (4.5m). For best
results, point the remote at the projector.
Remove batteries from the remote control when storing or not in use for a
prolonged period.
To operate, point the remote at the front of the projector (not at the computer).
The range of optimum operation is about 15 feet (4.5m).
Press the remote’s Power button to turn the projector on and off (see page 11 for
shutdown info).
navigation
buttons
Press the remote’s Menu button to open the projector’s menu system. Use the
arrow buttons to navigate, and the Select button to select features and adjust
The remote also has:
•
•
Volume buttons adjust the sound.
Custom button that can be assigned to a special function, like Blank Screen or
•
Source button brings up a menu of all possible sources allowing the user to
switch the active source.
•
•
•
Blank button to blank the screen.
Mute button to silence the audio.
Download from Www.Somanuals.co2m0. All Manuals Search And Download.
Using the audio
Using the projector’s speakers
connect audio cable
Connect the audio source to the Audio 1/Audio 2 connectors to hear audio
through the projector speakers.
Amplified speakers may also be connected to the projector using the Audio Out
connector.
To adjust the volume, press the Volume buttons on the remote.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
•
Make sure the audio cable is connected to the Audio 1/Audio 2 connector on
the projector, and that the other end of the cable is connected to an Audio
Out connector on the source (not a “line-in” or “microphone” connector).
•
Make sure the volume is turned up enough. Press the Volume button on the
remote.
•
•
•
Make sure the correct source is active.
Adjust the audio source.
If playing a video, make sure the playback has not been paused.
Download from Www.Somanuals.co2m1. All Manuals Search And Download.
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of
their functions:
Right arrow - When the menu is displayed, the right arrow button navigates
through the menu.
Up arrow/Keystone - When the menu is displayed, the up arrow button navigates
through the menu. When the menu is not displayed, this button adjusts the
Down arrow/Keystone - When the menu is displayed, the down arrow button
navigates through the menu. When the menu is not displayed, this button adjusts
menu navigation
buttons
Left arrow - When the menu is displayed, the left arrow button navigates through
the menu.
Enter - Activates the selected On-Screen Display (OSD) menu item.
Menu/Exit - Turns on the On-Screen Display (OSD) menu. Goes back to previous
OSD menu, exits and saves menu settings.
Auto - Resynchronizes the projector to the source.
Blank - Displays a solid color or factory logo screen.
Source - Brings up a menu of available sources.
Download from Www.Somanuals.co2m2. All Manuals Search And Download.
Optimizing computer images
After the projector is running and the image is on the screen, you can optimize the
image using the onscreen menus. For general information on using the menus, see
Presentation features
Several features are provided to make giving presentations easier. Here is an
overview, details are found in the menu section.
•
The Custom key allows you to assign various features to the button. The
default effect is Source Info, which displays information about the projector
•
•
•
Select default image settings using a preset appropriate to your environment.
•
•
•
•
The Search Screen option lets you change the appearance of the blank screen
Change the Aspect Ratio. Choose the option that best fits your input source
Auto Off Time is provided to automatically shut down the projector after
•
•
•
When the projector is connected to the computer via USB Type B, the up
and down arrows an be used as page up and page down controls.
Once you have optimized the image for a particular source, you can save the
settings using Presets. This allows you to quickly recall these settings later
When the projector is connected to the computer via USB Type B, the
projector will prevent the computer from going into screen saver mode
during your presentation.
Download from Www.Somanuals.co2m3. All Manuals Search And Download.
Optimizing video images
After your video device is connected properly and the image is on the screen, you
can optimize the image using the onscreen menus. For general information on
Customizing the projector
You can customize the projector for your specific setup and needs. See page 28
for details on these features.
•
For rear projection, turn Rear Project on in the Advanced Menu > Setup >
Image Setup... menu.
•
•
•
•
For ceiling mounted projection, turn Ceiling Mount on in the Basic menu.
Change the Aspect Ratio. Choose the option that best fits your input source
Specify which source the projector checks first for active video during power-
up.
•
•
•
•
•
•
•
•
•
Specify the function of the Custom key on the remote.
Turn the projector’s display messages on and off.
Turn on power saving features.
Specify appearance of blank screen and startup screen.
Specify the language viewed on the menus.
Save settings for the active source as a preset.
Download from Www.Somanuals.co2m4. All Manuals Search And Download.
Using the menus
1 To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) Use the
arrow buttons to move up and down to review the menu options.
keypad navigation
buttons
2 To enter a submenu, highlight the desired submenu and press > on the keypad
or Select on remote.
3 To adjust a menu setting, highlight the desired menu option and press < or >
to scroll through the available adjustments.
4 Press the Menu button to exit the menu system.
The menus are grouped by usage:
•
•
The Basic Menu provides common adjustments.
The Advanced Menu provides more complex adjustments.
MDL: IN112a
FW: 0.14
(
Basic Menu
)
MDL: IN112a
FW: 0.14
(
Advanced Menu
)
Aspect Ratio
Auto Image
Brightness
Contrast
Auto Keystone
Keystone
◄ Auto ►
Execute
50
50
Off
0
Image
3D Control...
Color...
Setup
Status/Service
PC...
Video...
Basic Menu
Presets
Presentation
Sharpness
Volume
Ceiling Mount
16
16
Off
Advanced Menu
Basic Menu
Advanced Menu
Download from Www.Somanuals.co2m5. All Manuals Search And Download.
Basic Menu
Basic Menu
MDL: IN112a
FW: 0.14
( Basic Menu )
Aspect Ratio
Auto Image
Brightness
Contrast
To adjust the following settings, highlight the setting, use the right and left arrows
to adjust the values.
◄ Auto ►
Execute
50
50
Off
0
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV
screens are usually 4:3. HDTV and most DVDs are 16:9.
Auto Keystone
Keystone
Presets
Sharpness
Volume
Presentation
Select Auto to have the projector choose the ratio. Choose Native to see the
unmodified input with no resizing by the projector. Select 16:9 to watch enhanced
widescreen DVDs.
16
16
Off
Ceiling Mount
Advanced Menu
Auto Image: resets the projector to the source.
Brightness: changes the intensity of the image.
Contrast: controls the degree of difference between the lightest and darkest parts
of the picture and changes the amount of black and white in the image.
Auto Keystone: automatically corrects distorted images resulting from an angled
projection.
Keystone: adjusts the image vertically and makes a squarer image. You can also
adjust keystone from the keypad.
Presets: Presets are provided that optimize the projector for displaying computer
presentations and video images under certain conditions. Note: Users can save
their settings as a User Preset.
increasing keystone
decreasing keystone
Sharpness: Changes the clarity of the edges of a video image. Select a sharpness
setting.
Volume: increases or decreases the audio volume.
Ceiling Mount: turns the image upside down for ceiling-mounted projection.
Download from Www.Somanuals.co2m6. All Manuals Search And Download.
White Intensity: increases the brightness of whites that are near 100%.
Advanced Menu
PC:
Image:
Force Wide: when this is off, the analog locking algorithms choose the stan-
dard mode resolution (4:3) as the preferred default resolution. When this is
on, the analog locking algorithms choose wide mode resolution (16:10) as the
preferred default resolution.
3D Control:
3D: allows you to enjoy 3D (stereoscopic) content. Your projector supports
Auto, Top-Bottom, Frame Sequential, Frame Packing, Side-by-Side for con-
trolling LCD shutter glasses. In addition to the projector, you will need a pair
of 3D shutter glasses, 3D content, and 3D compatible source (and emitter).
Ensure the glasses you choose are consistent with the synchronization mode
you will be using.
Phase: adjusts the horizontal phase of a computer source.
Prevent PC Screen Saver: prevents your computer from going into Screen
Save mode. The projector must be connected to the PC via a USB cable for
this feature to work.
3D Sync Invert: If the image appears to flutter, look odd or if the image depth
looks off or you experience eye strain, turn this feature on to see if the image
improves.
Sync Threshold: (progressive signals only) If a hardware device, such as a
DVD player, is not syncing properly with the projector, select this option to
help it to sync when connected to the projector.
Color...
Color: adjusts a video image from black and white to fully saturated color.
The color setting applies to video sources only.
Tracking: adjusts the vertical scan of a computer source.
Horizontal/Vertical Position: adjusts the position of a computer source.
Red/Green/Blue Gain: adjusts the gain of the red, green or blue channel of the
image.
Video:
Detect Film: determines whether the original source of the input video was
Red/Green/Blue Offset: adjusts the offset of the red, green or blue channel of
the image.
film (progressive) or video (interlaced).
Overscan: removes noise around the video image.
Color Space: applies to computer and component video sources. It allows
you to select a color space that has been specifically tuned for the input signal.
When Auto is selected, the projector automatically determines the standard.
To choose a different setting, turn off Auto, then choose RGB for computer
sources or choose either REC709 or REC601 for component video sources.
Set Black Level: analyzes the current input image and calculates an offset value
which is then added to the analog to digital converter black level value. This
ensures optimum black level for each analog source.
Color Temperature: changes the intensity of the colors. Select a listed rela-
tive warmth value.
Gamma: select the appropriate gamma from among Video, Film, Bright, and
CRT.
Tint: adjusts the red-green color balance in the image of NTSC video images.
The tint setting applies to NTSC video sources only.
Download from Www.Somanuals.co2m7. All Manuals Search And Download.
Ceiling Mount: turns the image upside down for ceiling-mounted projection.
Advanced Menu
MDL: IN112a
FW: 0.14
( Advanced Menu )
Rear Project: reverses the image so you can project from behind a translu-
cent screen.
Image
3D Control...
Setup
Status/Service
Color...
PC...
Keypad/Remote Settings...
Video...
Basic Menu
Blank Key: select what to display when the blank key on the remote is
pressed:, a solid color screen (blue, black or white), or the factory logo
screen.
Custom Key: allows you to assign a different function to the Custom button,
allowing you to quickly and easily use the effect. Highlight an effect and press
^ or v on the keypad or Select on remote to choose a different one.
•
•
•
•
•
•
•
•
•
•
Blank Screen: displays a solid color or factory logo screen.
Mute: turns off all sound.
Setup:
Audio Setup...
Source: brings up a menu of available sources.
Auto Image: resets the projector to the source.
Freeze Screen: pauses the projected image.
Source Info: the default action. Shows the Source Info menu.
Projector Info: shows the Projector Info menu.
Overscan: removes noise around the image.
AV Mute: enables or disables AV Mute function.
Closed Captions: enables or disables Closed Captions.
Internal Speaker: turns the internal speaker on or off.
Computer 1: selects the audio input for Computer 1 signal.
Computer 2: selects the audio input for Computer 2 signal.
Video: selects the audio input for video source.
HDMI: select the audio input for HDMI signal.
Closed Captioning...
Keypad: enables or locks the projector keypad.
Closed Captions: controls closed captioning. If the source is NTSC and
contains captions on the selected channel, then the projector will display
caption text overlaid on the image. When Closed Captions is off and volume
is muted, closed captioning will appear. Options are: Off, CC1 and CC2.
Image Setup...
Digital Zoom: reduces the size of projector’s display area. If the display area
has been resized by this setting, it can be moved by changing the Horz Shift
and Vert Shift settings.
Magnify Level: magnifies the image. If the image has been magnifiedby this set-
ting, it can be moved by changing the Horz Shift and Vert Shift settings.
Download from Www.Somanuals.co2m8. All Manuals Search And Download.
Lamp...
Programmed Dimming: When enabled, Programmed Dimming enhances con-
To change the PIN:
Select “Change PIN...” in the Advanced Menu > Setup > PIN settings menu.
Enter the existing PIN. Enter the new PIN.
trast ratios in dark scenes and disables Lamp Low Power. Programmed Dim-
ming will impact lamp life and system noise performance. Programmed
Dimming works in conjunction with the lamp. If Lamp Low Power is enabled,
Programmed Dimming is unavailable.
Power
Power Saving Mode: When the Power Saving Mode is On and the projector is
in standby (powered off but connected to AC power), external audio and the
Monitor Out function will not work.
Lamp Low Power: toggles between on and off. Turn it on to lower the light
output of the lamp. This also lowers the fan speed, making the projector qui-
eter.
AC Power On: When this feature is enabled, the projector automatically
turns on when power is connected. This allows control of ceiling mounted
projectors with a wall power switch.
OSD Setup...
Language: allows you to select a language for the onscreen display.
Instant Power On: When this feature is enabled and it has been less than 1
minute since the projector was powered down, you can turn the projector
back on immediately. When this feature is disabled, you will need to wait for
the projector lamp to completely cool before restarting the projector.
Menu Position: allows you to change the position of the On Screen Display
items.
Menu Transparency: allows you to change how much of the projected image
behind the menu you can see. As the value increases, more of the image
behind the menu is visible.
Eco Blanking: When this feature is enabled and no video source is sensed,
70% of lamp power is saved and no image is shown. When the video source is
again applied, the image is shown immediately.
Show Messages: displays status messages (such as “Searching”) in the lower-
left corner of the screen.
Source
PIN Settings
Auto Source: When this feature is On, the projector automatically finds the
active source, checking the selected Power-up Source first. When this feature
is Off, the projector defaults to the source selected in Power-up Source. To
display another source, you must manually select one by pressing the Source
button on the remote or keypad and selecting one from the displayed Source
menu.
PIN Protect: The PIN (personal identification number) feature allows you to
password protect your projector. Once you enable the PIN feature, you must
enter the PIN before you can project an image. Use the Up/Down/Left/Right
arrows buttons on the remote or keypad to set a 4-button press sequence. If
you enter an incorrect PIN 3 times in succession, the projector will automat-
ically shut down. If you lose or forget your custom PIN, contact InFocus
Technical Support.
Power-up Source: determines which source the projector checks first for
active video during power-up.
To enter the PIN at projector startup:
Search Screen: allows you to display a blank screen instead of the default
screen at startup, and when no source is detected.
Power up the projector. The “Enter PIN” dialog box appears after the startup
screen. Enter the PIN. Use the Up/Down/Left/Right arrows buttons on the
remote or keypad to enter the correct 4-button press sequence. See the
description above for instructions.
Download from Www.Somanuals.co2m9. All Manuals Search And Download.
Timer
Auto Off Time: automatically turns the projector off after no signals are
detected for a preset number of minutes. If an active signal is received before
the projector powers down, the image will be displayed.
High Altitude Setting
High Altitude: We recommend you turn on the High Altitude Mode when
your environment is between 5000' (1500m) and 10,000' (3000m) above sea
level.
Status/Service:
Source Info: a read-only display of current source settings.
Projector Info: a read-only display of current projector settings and lamp
hours.
Reset Lamp Hours...: resets the lamp hours used counter in the Projector
Info menu to zero. Do this only after changing the lamp.
Factory Reset...: restores all settings to their default.
Service Code...: only used by authorized service personnel.
Download from Www.Somanuals.co3m0. All Manuals Search And Download.
Maintenance
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Projector must be off and the lens must be at room temperature.
• Avoid using an excessive amount of cleaner, and don’t apply the cleaner
directly to the lens. Abrasive cleaners, solvents or other harsh chemicals
might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS:
• Turn the projector off and unplug power cord before cleaning any part of
the projector.
• Do not touch or block the projector lens with any objects as this can
damage the projector lens. Scratches, gouges and other lens damage are not
covered by the product warranty.
• Do not open any cover on the projector, except the lamp cover.
• Do not attempt to service this product yourself as opening and removing
covers may expose you to dangerous voltage and other hazards. Refer all
servicing to qualified service personnel.
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to the
information that came with the lock for instructions on how to use it.
security
lock
Download from Www.Somanuals.co3m1. All Manuals Search And Download.
Hg – Lamp contains mercury. Manage in accordance with local disposal
Replacing the projection lamp
The Lamp Hours timer in the Projector Info menu counts the number of hours the
lamp has been in use.
•
NOTE: Be sure to use the InFocus lamp module designed for this projector.
retailer or your dealer. Only genuine InFocus lamps are tested for use in this
projector. Use of non InFocus lamps may cause electrical shock and fire, and
may void the projector warranty. InFocus is not liable for the performance,
safety or certification of any other lamps.
WARNINGS:
•
The projector uses a high-pressure mercury glass lamp. The lamp may fail
prematurely, or it may rupture with a popping sound if jolted, scratched, or
handled while hot. The risk of lamp failure or rupture also increases as the
lamp age increases; please replace the lamp when you see the “Replace Lamp”
message.
•
•
To avoid burns, allow the projector to cool for at least 60 minutes before you
replace the lamp.
Do not touch or block the projector lens with any objects as this can damage
the projector lens. Scratches, gouges and other lens damage are not covered
by the product warranty.
•
•
•
Unplug the power cord before replacing the lamp.
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass surface of the lamp module. Fingerprints can obscure
projection sharpness and may cause the glass to shatter.
•
Be extremely careful when removing the lamp housing. In the unlikely event
that the lamp ruptures, small glass fragments may be generated. The lamp
module is designed to contain most of these fragments, but use caution when
removing it.
•
•
Before replacing a ruptured lamp, clean the lamp compartment and dispose of
cleaning materials. Wash hands after lamp replacement.
When replacing the lamp while the projector is ceiling-mounted, wear
protective eyewear to prevent eye injury.
Download from Www.Somanuals.co3m2. All Manuals Search And Download.
1 Turn off the projector and unplug the power cord.
turn off and unplug
projector
wait 60 minutes
2 Wait 60 minutes to allow the projector to cool thoroughly.
3 Remove the lamp door, located on top of the projector, by removing the
screw on the side of the lamp door, sliding the door right, and lifting the lamp
door off.
4 Loosen the captive screws that attach the lamp housing to the projector.
NOTE: If the projector is installed on a ceiling mount, be careful not to drop
the lamp module once the captive screws are loosened.
5 Carefully lift the lamp straight up, off of the alignment pins; being careful not to
pinch the lamp connector. Dispose of the lamp in an environmentally proper
manner.
loosen screws
6 Install the new lamp module, aligning the pins properly. Be careful not to pinch
the lamp connector.
7 Tighten the screws. (NOTE: If the pins have not been aligned properly, the
screws will not tighten securely.)
8 Replace the lamp door by (a) putting the lamp door down and (b) sliding it
until it locks.
9 Replace the lamp door screw and tighten securely.
MDL: IN112a
FW: 0.14
( Advanced Menu )
10 Plug in the power cord and press the Power button to turn the projector back
on.
Image
Source Info...
Setup
Projector Info...
Reset Lamp Hours...
Factory Reset...
Service Code...
Status/Service
11 To reset the lamp hour timer, navigate to the Advanced Menu > Status/Service
menu and select Reset Lamp Hours....
Basic Menu
Download from Www.Somanuals.co3m3. All Manuals Search And Download.
Numerics
F
A
G
H
B
I
K
L
M
C
Connecting
D
O
E
P
Download from Www.Somanuals.co3m4. All Manuals Search And Download.
Projector
U
V
W
Z
R
S
T
Download from Www.Somanuals.co3m5. All Manuals Search And Download.
|