Bluetooth Wireless Stereo Solution
User Manual (GBMA201, GBMH201, GBMHKIT)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Package Contents
2
System Requirements
Introdution
3
4
Instructions for GBMHKIT/GBMA201
- Operation
7
8
- Pairing headphones and audio transmitter
Instructions for GBMH201
- Operation
10
13
14
- Pairing with Bluetooth-enable device
Using Headphones with Bluetooth cell phone
Audio Playback: How it works
Troubleshooting
15
19
23
26
27
28
Technical Support
FCC Statement
Limited Warranty
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents
GBMH201
GBMA201
1– Bluetooth Stereo Headphone
1– Detachable Microphone
1– Carrying Bag
1– Power Adapter
1– Quick Start Guide
1– Warranty/Registration card
1– Bluetooth Audio Transmitter
1– 3.5mm to RCA audio cable
1– 3.5mm to ¼” Stereo Phono Connector
1– 3.5mm Extension Cable
1– Power Adapter
1– Quick Start Guide
1– Warranty/Registration Card
GBMHKIT:
1– BluetoothStereo Headphone
1– Bluetooth Audio Transmitter
1– Detachable Microphone
1– Carrying Bag
1– Power Adapter
1– Power Cable Splitter
1– 3.5mm Extension Cable
1– 3.5mm to RCA Audio Cable
1– 3.5mm to 1/4" Stereo Phono Connector
1– Quick Start Guide
1– Warranty/Registration Card
2
Download from Www.Somanuals.com. All Manuals Search And Download.
System Requirements
For stereo sound (headphones):
Bluetooth-enabled music source must support
Advanced Audio Distribution Profile (A2DP)
For cell phone use:
Bluetooth cell phone must support either Headset
or Hands-Free Profile
*Note: Functionality of the Back/Forward headphone buttons requires Bluetooth software with support
for the Audio/Video Remote Control Profile (AVRCP).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Headphones
1. Center button – multiple functions include
a) turn headset on/off;
b) pause/play music;
c) mute/un-mute sound
d) accept/terminate phone call
2. Volume up button
3.Volume down button
4. Forward button*
10
5. Back button*
6. Bluetooth LED
1
5
3
7. Power LED
8. Microphone jack
9. Power jack
10. Foldable neck band
8
9
4
5
6
7
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
AudioTransmitter :
1. ON/OFF button
2. Power jack
3. Status LED
4. 3.5mm audio connector
5. Removable rubber for iPod Mini users
1
2
iPOD Mini Users
To properly fit iPOD Mini, the connector on the audio
transmitter is slideable, Simply remove the rubber
located to the right side of the audio connector.
You will then be able to slide the audio connector to
the right for a perfect fit on the iPOD Mini.
3
5
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Headset LEDs
Blue LED
· Solid when connected to a Bluetooth device
· Blinks slowly when the power is on and it is waiting for a Bluetooth connection
· Blinks rapidly when ringing (incoming call)
Red LED
· Solid when charging
· Off when fully charged
Audio Transmitter LEDs
Blue LED
· Blinks rapidly when Powered ON
· Solid when connected
· Blinks twice per second when searching for headphones
Red LED
· Solid when charging
· Solid when charging
· Off when finished charging
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - GBMH KIT
HEADPHONES
Charge Headphones
1. Before first use, you must fully charge the headphones for at least 2 hours.
2. Each full charge gives you approximately 6.5 hours of continuous operation.
Turn ON Headphones
1. Press and hold the Center button for approximately 6 seconds
2. The Blue LED will quickly flash, indicating it’s ready to accept a Bluetooth connection
Turn OFF Headphones
1. Press and hold the Center button for approximately 4 seconds until the blue LED turns off
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - GBMH KIT
AUDIO TRANSMITTER
Charge transmitter
1. Before first use, you must fully charge transmitter for at least 2 hours
2. Each full charge gives you approximately 6.5 hours of continuous operation
Turn ON transmitter
1. Press and hold the ON/OFF button for 2 seconds
2. The blue LED will begin flashing rapidly, waiting for a Bluetooth connection
Turn OFF transmitter
1. Press and hold the ON/OFF button for 5 seconds; the blue LED will turn off
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - GBMH KIT
For GBMHKIT Only:
The Bluetooth KIT (headphones and transmitter)
should already come pre-paired from factory, and
all you need to do is turn both of them ON.
Follow the procedure below:
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - GBMH KIT
Step 1-Turn ON Bluetooth Headphones
Press and hold the Center button for approximately six seconds until the blue LED starts flashing
Step 2 -Turn ON Bluetooth transmitter
Press and hold the ON/OFF button for approximately three seconds until the blue LED starts flashing
Step 3 - Auto-connect
Wait approximately 60 seconds as both devices search for each other and auto-connect. When the
blue LED stops flashing and becomes solid on both devices, this indicates successful connection
Step 4 - Finished
Simply plug in the transmitter to your favorite music device and enjoy!
Note: The Bluetooth headphones may also be used with a Bluetooth-enabled device that supports the
A2DP profile. For more information, consult the section of the manual “Instructions for GBMH201”.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - GBMA201
GBMA201:
Setting the transmitter in Inquiry Mode
Follow the procedure below if:
·You purchased the headphones (GBMH201) and transmitter (GBMA201) separately (not part of a kit),
or
·You have GBMHKIT, but are having trouble getting the headphones and transmitter paired, or
·You are using non-IOGEAR Bluetooth headphones with the transmitter (GBMA201). For a list of
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - GBMA201
Step 1 –Turn OFF
Turn OFF both audio transmitter and headphones
Step 2 – Inquiry Mode
Press and hold the ON/OFF button on the transmitter for approximately 6 seconds to invoke inquiry
mode.
Step 3 –Turn ON
Turn ON Bluetooth headphones by pressing the Center button for 6 seconds. If using non-IOGEAR
headphones, consult your manual for instructions.
Step 4 – Auto-Connect
The transmitter will now begin searching for Bluetooth headphones within range and connect to the
closest one. Please be patient as it may take 60-120 seconds for both devices to connect.
Step 5 – Finished
When the blue LED becomes solid on both devices, this indicates successful connection
If you encounter problems, please consult the troubleshooting section of this manual.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - GBMH201
HEADPHONES
ChargeHeadphones
1. Before first use, you must fully charge the
headphones for at least 2 hours.
2. Each full charge gives you approximately 6
hours of continuous operation.
Turn ON Headphones
1. Press and hold the Center button for
approximately six seconds
2. The Blue LED will quickly flash, indicating
it’s ready to accept a Bluetooth connection
Turn OFF Headphones
1. Press and hold the Center button for
approximately four seconds until the blue
LED turns off
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - GBMH201
The Bluetooth headphones can be used with any computer, PDA, phone, MP3 player, or any other
type of device that supports the following Bluetooth profiles:
· A2DP (Advanced Audio Distribution Profile) for stereo sound
· AVRCP (Audio Video Remote Control Profile) for functionality of the Back/Forward buttons
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - GBMH201
Below is an example on how to pair and connect to the headphones using Widcomm Bluetooth
software version 4.0.x. (PC version).
Step 1 -Turn ON Bluetooth Headphones
Press and hold the Center button for
approximately 6 seconds until the blue LED
starts flashing
Step 2 – Open Bluetooth software
Make sure Bluetooth function is enabled on
your computer and open Bluetooth application
(ex: My Bluetooth Places).
Step 3 - Search for devices in range
On the left side, click on “View devices in
range” to search for the IOGEAR headphones.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - GBMH201
Step 4 – Pairing
When the IOGEAR Headphones are found, right
click on its icon and select Pair Device
If prompted for a PIN code, enter “0000” (four
zeroes)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - GBMH201
Step 3 – Connect
Once paired, right-click on its icon and select
the option “Connect Audio Sink”. Wait while the
computer/PDA connects to the Headphones.
Upon successful connection, the headphones
blue LED will stop flashing and become solid
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - GBMH201
Step 4 – Finished
When connected, the headset icon will turn green as below. You may now exit the Bluetooth software.
IOGEAR Headphones
Simply launch your music/movie software application and enjoy!
If you encounter problems, please consult the troubleshooting section of this manual.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
UsingWith A Cell Phone
Once paired with your Bluetooth cell phone, you
can make/receive phone calls through the
IOGEAR headphones (using the included
detachable microphone).
If you make/receive a phone call during music
playback, pressing the Center button will pause
the music and transfer audio to the cell phone,
and automatically resume music at the end of
your call.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Phone Pairing Procedure
Step 1 – Setup Phone
Make sure your cell phone’s Bluetooth functionality is turned ON
Step 2 –Turn ON Bluetooth headphones
Press and hold the Center button for approximately 6 seconds until the blue LED starts flashing
Step 2 – Search for Bluetooth headphones
Follow your cell phone instructions to search for Bluetooth devices
Step 3 – Pair and Connect
Once the IOGEAR headset is found, select it and pair to it. If prompted for a PIN code, enter “0000”
(four zeroes).
Step 4 – Finished
You should now be able to use the Bluetooth headset to make/receive phone calls through your
Bluetooth cell phone.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Making a call
Simply dial the number as usual from your cell phone; the voice will be directed to the headset
During music/audio playback, pressing keys on your cell phone will automatically transfer control of
the headphones to the cell phone, and music will be paused. Upon phone call termination, the music
will resume after approximately 5 seconds.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Making a call
Simply dial the number as usual from your cell phone; the voice will be directed to the headset
During music/audio playback, pressing keys on your cell phone will automatically transfer control of
the headphones to the cell phone, and music will be paused. Upon phone call termination, the music
will resume after approximately 5 seconds.
Answering a call
1.You will hear a ring tone on the headset during an incoming call
2. Press the Center button once to pick up the incoming call. During music/audio playback, pressing
the Center button will pause the music, and resume after phone call is terminated.
Tip: If you wish to reject the call, press any other button
Ending a call
1. Press the Center button to end the call
Mute/Un-mute microphone
· During a phone conversation, you may mute the microphone so that your voice will not be heard on
the other end; simply press the Forward or Back button
· To un-mute, press the Forward or Back button again
22
Download from Www.Somanuals.com. All Manuals Search And Download.
How It Works
Using Headphones with Bluetooth transmitter
Simply follow the pairing procedure as indicated on the manual, and then plug in the audio transmitter
to any of your devices. The music will transfer to the headset, as if you were using any standard
headphones.
Using Headphones with Bluetooth Computer
Typically, after establishing the Bluetooth connection with the headphones, you will be able to listen
to audio from your device without having to do any changes to your sound settings.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
If this is not the case, however, you may make this change manually by doing the following:
1. Go to Control Panel and then double-click on
“Sounds and Audio Devices.”
2. This will open up the Sound Properties window
3. Select the Audio tab on top, and under the
“Sound playback option”, make sure to select
“Bluetooth High Quality Audio.” Now click
Apply and then OK.
4. Now, the default device for audio playback will
be the Bluetooth Headphones.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
*The Bluetooth transmitter only has the capability to send audio signals out. For functionality of the
Back/Forward buttons, your Bluetooth-enabled device or software must support the AVRCP Bluetooth
profile.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
1. The headphone control buttons have stopped responding or behave strangely.
This might be an indication that the batteries are low and need re-charging. Please allow the batteries to charge for
approximately 2 hours.
2. I have followed the instructions but I do not hear any sound on the headphones.
a) Make sure volume is not muted on your computer/PDA or other device.
b) Turn volume up on the headset control buttons
c) If your music/video software application was opened prior to setting up the Bluetooth headset,
you might need to close the application and re-open it again
d) Make sure all required drivers for your sound card have been properly loaded in your computer;
otherwise, the headphones will not function.
3. If you are having trouble pairing the IOGEAR Bluetooth headphones with the audio transmitter, follow
the procedure below:
a) Turn OFF audio transmitter and headphones
b) Press and hold the ON/OFF button on the transmitter for approximately six seconds to set it in Inquiry Mode.
c) Turn ON Bluetooth headphones
d) The headphones and transmitter will search for each other and auto-connect.
e) When the blue LED becomes solid on both devices, this indicates successful connection
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Support
If you need technical support, please check out our IOGEAR Tech Info Library (T.I.L.) at
designed to provide you with the latest technical information about our products. Most of the answers
to your questions can be found here, so please try it out before contacting technical support.
Technical Support is available Monday through Friday from 7:30 a.m. to 5:30 p.m. PST and can be
reached at Toll-Free (866) 946-4327 or by email support@iogear.com
27
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the
user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause undesired operation of the device.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the
specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
IN NO EVENT SHALLTHE DIRECTVENDOR’S LIABILITY FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROMTHE USE OFTHE PRODUCT,
DISK, OR ITS DOCUMENTATION EXCEEDTHE PRICE PAID FORTHE PRODUCT.
The direct vendor makes no warranty or representation, expressed, implied, or statutory with respect
to the contents or use of this documentation, and especially disclaims its quality, performance,
merchantability, or fitness for any particular purpose.
The direct vendor also reserves the right to revise or update the device or documentation without
obligation to notify any individual or entity of such revisions, or updates. For further inquires please
contact your direct
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact Information:
Download from Www.Somanuals.com. All Manuals Search And Download.
|