Woods Equipment Lawn Mower Accessory RB750 4 User Guide
REAR BLADES  
RB750-4  
RB850-4  
Tested. Proven. Unbeatable.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
OWNER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 48  
PRODUCT WARRANTY . . . . . . . . . . . . . . . . . . . . . . . INSIDE BACK COVER  
REPLACEMENT PARTS WARRANTY . . . . . . . . . . . . . . . . . . BACK COVER  
!
LEA EL INSTRUCTIVO!  
Si no lee Ingles, pida ayuda a  
alguien que si lo lea para que le  
traduzca las medidas de seguridad.  
GENERAL INFORMATION  
The purpose of this manual is to assist you in oper-  
The illustrations and data used in this manual were  
current at the time of printing. However, due to pos-  
sible inline production changes, your machine may  
vary slightly in detail. We reserve the right to rede-  
sign and change the machines as may be neces-  
sary without notification.  
ating and maintaining your Rear Blade. Read it  
carefully. It furnishes information and instructions  
that will help you achieve years of dependable per-  
formance. These instructions have been compiled  
from extensive field experience and engineering  
data. Some information may be general in nature,  
due to unknown and varying operating conditions.  
However, through experience and these instruc-  
tions, you should be able to develop procedures  
suitable to your particular situation.  
Throughout this manual, references are made to  
right and left directions. These are determined by  
standing behind the tractor facing the direction of  
forward travel.  
MAN0160 (Rev. 8/19/2005)  
Introduction 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RB750-4 & RB850-4 SPECIFICATIONS  
MODEL  
RB750-4  
RB850-4  
Blade Width  
7 ft. (2133 mm)  
8 ft. (2438 mm)  
Tractor HP Requirement  
100 HP Maximum  
(75 kW)  
100 HP Maximum  
(75 kW)  
Weight:  
M = Manual  
811 lbs. (368 kg)  
1010 lbs. (458 kg)  
856 lbs. (388 kg)  
1050 lbs. (478 kg)  
H = Hydraulic  
Model Codes:  
M
= All Manual: Angle, Tilt & Swing  
MA = Manual Swing & Tilt; Hydraulic Angle for tractors with at least one hydraulic port  
MT = Manual Swing & Angle; Hydraulic Tilt for tractors with at least one hydraulic port  
SA = Manual Tilt; Hydraulic Swing & Angle for tractors with at least two hydraulic ports  
TA = Manual Swing; Hydraulic Tilt & Angle for tractors with at least two ports  
H
= All Hydraulic; Angle, Tilt & Swing for tractors with three hydraulic ports  
Blade Position - Mechanical . . . . . . Straight, forward or reverse;  
Angle 15, 30, 45 & 60 degrees, right or left in forward;  
15 & 30 degrees in reverse;  
Tilt 15 or 30 degrees up or down;  
Offset 12" or 24" (305 mm or 610 mm) left or right of  
tractor center line;  
Pitch adjustment in top link of tractor 3-point hitch  
Blade Positions - Hydraulic . . . . . . . Straight, forward or reverse;  
Angle 45 degrees right or left forward and reverse;  
Tilt 22 degrees up or down;  
Offset 24" (610 mm) right or left of tractor center line;  
Pitch adjustment in top link of tractor 3-point hitch  
Cutting Edge . . . . . . . . . . . . . . . . . . 1/2 x 6" (12.7 mm x 152 mm) High carbon steel, reversible  
3-Point Hitch Category . . . . . . . . . . Category 2  
Category 2 Quick attaching coupler, with bushing kit #18295  
Category 3, with bushing kit #18295  
Structural Strength:  
A-Frame . . . . . . . . . . . . . . . . . . . . . 8 x 4 (203 mm x 102 mm) Formed channel  
Boom. . . . . . . . . . . . . . . . . . . . . . . . All-welded box section  
King Pin. . . . . . . . . . . . . . . . . . . . . . 6-5/8" (168 mm) Tubing  
Moldboard . . . . . . . . . . . . . . . . . . . . Formed moldboard and all welded box section  
Pivot Assembly . . . . . . . . . . . . . . . . All-welded steel box section  
MAN0160 (Rev. 8/19/2005)  
4 Introduction  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY RULES  
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!  
PREPARATION  
„ Check that all hardware is properly installed.  
Always tighten to torque chart specifications  
unless instructed otherwise in this manual.  
Safety is a primary concern in the design and  
manufacture of our products. Unfortunately, our  
efforts to provide safe equipment can be wiped  
out by an operator’s single careless act.  
„ Do not connect a low-pressure hydraulic hose  
into a high-pressure system—it will burst the hose.  
Do not use a high-pressure hose in place of a low-  
pressure hose—it is possible to rupture the valve.  
In addition to the design and configuration of  
equipment, hazard control and accident preven-  
tion are dependent upon the awareness, concern,  
judgement, and proper training of personnel  
involved in the operation, transport, maintenance  
and storage of equipment.  
„ Always wear relatively tight and belted clothing  
to avoid entanglement in moving parts. Wear  
sturdy, rough-soled work shoes and protective  
equipment for eyes, hair, hands, hearing, and head.  
It has been said “The best safety device is an  
informed, careful operator.” We ask you to be that  
kind of operator.  
„ Make sure attachment is properly secured,  
adjusted, and in good operating condition.  
„ Power unit must be equipped with ROPS or  
ROPS cab and seat belt. Keep seat belt securely  
fastened. Falling off power unit can result in death  
from being run over or crushed. Keep foldable  
ROPS systems in “locked up” position at all times.  
TRAINING  
„ Safety instructions are important! Read all  
attachment and power unit manuals; follow all  
safety rules and safety decal information. (Replace-  
ment manuals and safety decals are available from  
your dealer. To locate your nearest dealer, check  
the Dealer Locator at www.WoodsEquipment.com,  
or in the United States and Canada call 1-800-319-  
6637.) Failure to follow instructions or safety rules  
can result in serious injury or death.  
„ A minimum 20% of tractor and equipment  
weight must be on the tractor front wheels when  
attachments are in transport position. Without this  
weight, tractor could tip over, causing personal  
injury or death. The weight may be attained with a  
loader, front wheel weights, ballast in tires or front  
tractor weights. Weigh the tractor and equipment.  
Do not estimate.  
„ If you do not understand any part of this manual  
and need assistance, see your dealer.  
„ Make sure all safety decals are installed.  
Replace if damaged. (See Safety Decals section for  
location.)  
„ Know your controls and how to stop engine and  
attachment quickly in an emergency.  
„ Operators must be instructed in and be capable  
of the safe operation of the equipment, its attach-  
ments, and all controls. Do not allow anyone to  
operate this equipment without proper instruc-  
tions.  
„ Make sure circuit selector lever does not hit  
tractor cab, etc. throughout operating range of 3-  
point hitch of tractor. Bend lever, if necessary, to  
clear cab, but it should still be convenient to oper-  
ate from the tractor seat.  
„ Keep hands and body away from pressurized  
lines. Use paper or cardboard, not hands or other  
body parts to check for leaks. Wear safety goggles.  
Hydraulic fluid under pressure can easily penetrate  
skin and will cause serious injury or death.  
OPERATION  
„ Do not allow bystanders in the area when oper-  
ating, attaching, removing, assembling, or servic-  
ing equipment.  
„ Do not operate equipment while under the influ-  
ence of alcohol or drugs.  
„ Make sure that all operating and service person-  
nel know that if hydraulic fluid penetrates skin, it  
must be surgically removed as soon as possible by  
a doctor familiar with this form of injury or gan-  
grene, serious injury, or death will result. CON-  
TACT A PHYSICIAN IMMEDIATELY IF FLUID  
ENTERS SKIN OR EYES. DO NOT DELAY.  
„ Operate only in daylight or good artificial light.  
„ Keep hands, feet, hair, and clothing away from  
equipment while engine is running. Stay clear of all  
moving parts.  
„ Always comply with all state and local lighting  
and marking requirements.  
„ Never allow children or untrained persons to  
operate equipment.  
(Safety Rules continued on next page)  
RB750/850-4 SR (Rev. 2/22/2006)  
Safety 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY RULES  
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!  
(Safety Rules continued from previous page)  
„ Do not operate or transport equipment while  
under the influence of alcohol or drugs.  
„ Never allow riders on power unit or attachment.  
„ Power unit must be equipped with ROPS or  
ROPS cab and seat belt. Keep seat belt securely  
fastened. Falling off power unit can result in death  
from being run over or crushed. Keep foldable  
ROPS systems in “locked up” position at all times.  
MAINTENANCE  
„ Before dismounting power unit or performing  
any service or maintenance, follow these steps:  
disengage power to equipment, lower the 3-point  
hitch and all raised components to the ground,  
operate valve levers to release any hydraulic pres-  
sure, set parking brake, stop engine, remove key,  
and unfasten seat belt.  
„ Always sit in power unit seat when operating  
controls or starting engine. Securely fasten seat  
belt, place transmission in neutral, engage brake,  
and ensure all other controls are disengaged  
before starting power unit engine.  
„ Before working underneath, read manual  
instructions, securely block up, and check stability.  
Secure blocking prevents equipment from drop-  
ping due to hydraulic leak down, hydraulic system  
failure, or mechanical component failure.  
„ Look down and to the rear and make sure area  
is clear before operating in reverse.  
„ Do not operate on steep slopes.  
„ Do not stop, start, or change directions sud-  
denly on slopes.  
„ Always wear relatively tight and belted clothing  
to avoid entanglement in moving parts. Wear  
sturdy, rough-soled work shoes and protective  
equipment for eyes, hair, hands, hearing, and head.  
„ Use extreme care and reduce ground speed on  
slopes and rough terrain.  
„ Watch for hidden hazards on the terrain during  
operation.  
„ Do not modify or alter or permit anyone else to  
modify or alter the equipment or any of its compo-  
nents in any way.  
„ Stop power unit and equipment immediately  
upon striking an obstruction. Turn off engine,  
remove key, inspect, and repair any damage before  
resuming operation.  
„ Make sure attachment is properly secured,  
adjusted, and in good operating condition.  
„ Never perform service or maintenance with  
engine running.  
„ Before changing positions of manual swing, tilt,  
or angle positions:  
„ Keep all persons away from operator control  
area while performing adjustments, service, or  
maintenance.  
•
Park tractor on level ground, apply parking  
brake, level implement boom, shut off tractor,  
and remove key.  
•
Make manual changes slowly and carefully  
„ Tighten all bolts, nuts and screws to torque  
chart specifications. Check that all cotter pins are  
installed securely to ensure equipment is in a safe  
condition before putting unit into service.  
to prevent hazardous movement of mecha-  
nisms.  
•
become entrapped during adjustment changes  
or if the 3-point hitch suddenly lowers.  
Never stand in positions where you could  
„ Make sure all safety decals are installed.  
Replace if damaged. (See Safety Decals section for  
location.)  
„ Always secure lock pins with safety pins to pre-  
vent lock pins from bumping out of the positioning  
holes. Failure to do so may result in accidents and/  
or damage to blade.  
„ Do not disconnect hydraulic lines until machine  
is securely blocked or placed in lowest position  
and system pressure is released by operating  
valve levers.  
TRANSPORTATION  
„ Before transporting, pivot the unit so red reflec-  
tors face the rear.  
STORAGE  
„ Secure equipment parking stand(s) in park posi-  
tion before detaching.  
„ Always comply with all state and local lighting  
and marking requirements.  
„ Keep children and bystanders away from stor-  
age area.  
„ Never allow riders on power unit or attachment.  
„ Do not operate or transport on steep slopes.  
RB750/850-4 SR (Rev. 2/22/2006)  
6 Safety  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY & INSTRUCTIONAL DECALS  
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!  
Replace Immediately If Damaged!  
CD5978A  
1 - SERIAL NUMBER PLATE  
MODEL NO.  
SERIAL NO.  
Woods Equipment Company  
Oregon, Illinois, U.S.A.  
2 - PN 19924  
6 - PN 57123  
RED REFLECTOR 9"  
WARNING  
7 - PN 1002940  
YELLOW REFLECTOR 9"  
Check for leaks with cardboard; never use hand.  
Before loosening fittings: lower load, release pressure, and  
be sure oil is cool.  
Consult physician immediately if skin penetration occurs.  
19924-B  
(Safety Decals continued on next page)  
MAN0160 (Rev. 8/19/2005)  
Safety 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY & INSTRUCTIONAL DECALS  
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!  
Replace Immediately If Damaged!  
(Safety Decals continued from previous page)  
3 - PN 1002941 4 - PN 1004250  
BE CAREFUL!  
Use a clean, damp cloth to clean  
safety decals.  
WARNING  
TO AVOID SERIOUS  
INJURY OR DEATH:  
WARNING  
Avoid spraying too close to decals  
when using a pressure washer;  
high-pressure water can enter  
through very small scratches or  
under edges of decals causing  
them to peel or come off.  
ꢀRead Operator's Manual  
before operating, servicing,  
or repairing equipment.  
Follow all safety rules and  
instructions. (Manuals are  
available from dealer or call  
1-800-319-6637.)  
CRUSHING AND  
PINCHING HAZARD  
ꢀBe extremely careful  
handling various parts of the  
machine. They are heavy and  
hands, fingers, feet, and  
other body parts could be  
crushed or pinched between  
tractor and implement.  
ꢀOperate from tractor seat  
only.  
Replacement safety decals can be  
ordered free from your Woods  
dealer. To locate your nearest  
dealer, check the Dealer Locator at  
www.WoodsEquipment.com, or in  
the United States and Canada call  
1-800-319-6637.  
ꢀLower equipment to ground,  
stop engine, remove key,  
and set brake before  
ꢀOperate tractor controls from  
tractor seat only.  
dismounting tractor.  
ꢀNever allow children or  
untrained persons to operate  
equipment.  
ꢀDo not stand between tractor  
and implement when tractor  
is in gear.  
ꢀNever allow riders.  
ꢀMake sure parking brake is  
engaged before going  
between tractor and  
implement.  
ꢀKeep bystanders away from  
equipment during operation.  
ꢀKeep all shields in place and  
in good condition.  
8 - PN 1003193  
ꢀStand clear of machine while  
in operation or when it is  
being raised or lowered.  
FAILURE TO FOLLOW THESE  
INSTRUCTIONS CAN RESULT  
IN INJURY OR DEATH.  
WARNING  
FAILURE TO FOLLOW THESE  
INSTRUCTIONS COULD  
RESULT IN SERIOUS INJURY  
1004250  
Unit must not extend  
more than 4 feet left of  
center of the tractor when  
driving on public roads.  
OR DEATH.  
1002941-A  
1003193-A  
5 - PN 55121  
WARNING  
FALLING OFF CAN RESULT IN BEING RUN OVER.  
„ Tractor must be equipped with ROPS (or ROPS CAB) and  
seat belt. Keep foldable ROPS systems in “locked up”  
position at all times.  
„ Buckle Up! Keep seat belt securely fastened.  
„ Allow no riders.  
RAISED IMPLEMENT CAN DROP AND CRUSH.  
„ Never go underneath raised implement which can drop  
from equipment or tractor 3-point hitch hydraulic leak  
down, hydraulic system failures, movement of control  
levers or mechanical linkage failures.  
„ Service work does not require going underneath  
implement. Read manual instructions.  
FALLING OFF OR GOING UNDERNEATH IMPLEMENT  
CAN RESULT IN SERIOUS INJURY OR DEATH.  
55121--C  
MAN0160 (Rev. 8/19/2005)  
8 Safety  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The Rear Blade is a 3-point Category 2 implement. It  
will attach to ASAE standard Category 2 quick-attach-  
ing coupler or on 3-point Category 3 tractor, using a  
bushing kit.  
„ Never allow children or untrained persons to  
operate equipment.  
NOTE: Only use on Category 3, 3-point hitch trac-  
tor whose lower lift arms adjust to 32" (813 mm)  
apart.  
„ Do not allow bystanders in the area when oper-  
ating, attaching, removing, assembling, or servic-  
ing equipment.  
1. Set the tractor drawbar in short-high position.  
„ Before working underneath, read manual  
instructions, securely block up, and check stability.  
Secure blocking prevents equipment from drop-  
ping due to hydraulic leak down, hydraulic system  
failure, or mechanical component failure.  
2. Attach tractor draft links to the A-frame with 1-1/8"  
pin (21) and secure with Klik pins (44).  
3. Connect the tractor top link to top hole in A-frame,  
using 1 x 4-29/32" heat-treated pin (20) and cotter  
pin (31). Use 1 x 1-1/4" bushing (23) and 1-1/8 x 1-  
7/16" heat-treated bushing (24) with Category 2  
quick- attaching coupler and category 3, 3-point  
hitch tractor.  
„ Never allow riders on power unit or attachment.  
„ Keep all persons away from operator control  
area while performing adjustments, service, or  
maintenance.  
4. Level the boom by adjusting lift and top link.  
„ Keep hands and body away from pressurized  
lines. Use paper or cardboard, not hands or other  
body parts to check for leaks. Wear safety goggles.  
Hydraulic fluid under pressure can easily penetrate  
skin and will cause serious injury or death.  
5. Position sway blocks to eliminate side sway or  
install sway braces if required.  
NOTE: The drawbar may have to be removed on  
some tractors. Make sure blade is at least 6" (152  
mm) from tractor tires throughout operating range  
of 3-point hitch.  
„ Make sure that all operating and service person-  
nel know that if hydraulic fluid penetrates skin, it  
must be surgically removed as soon as possible by  
a doctor familiar with this form of injury or gan-  
grene, serious injury, or death will result. CON-  
TACT A PHYSICIAN IMMEDIATELY IF FLUID  
ENTERS SKIN OR EYES. DO NOT DELAY.  
„ A minimum 20% of tractor and equipment  
weight must be on the tractor front wheels when  
attachments are in transport position. Without this  
weight, tractor could tip over, causing personal  
injury or death. The weight may be attained with a  
loader, front wheel weights, ballast in tires or front  
tractor weights. Weigh the tractor and equipment.  
Do not estimate.  
CD5979-1  
CAUTION  
„ Always wear relatively tight and belted clothing  
to avoid entanglement in moving parts. Wear  
sturdy, rough-soled work shoes and protective  
equipment for eyes, hair, hands, hearing, and head.  
1. A-Frame  
20. Clevis pin 1 x 4-29/32 HT  
21. Hitch pin 1-1/8  
23. Sleeve 1 x 1-1/4 x 2  
24. Sleeve 1-1/8 x 1-7/16 x 2-5/8  
31. Cotter pin 1/4 x 1-3/4  
44. Klik pin 7/16 x 11/32 HT  
MOUNT BLADE TO TRACTOR  
IMPORTANT  
■
The RB750-4 & RB850-4 should be mounted on  
tractors with a maximum horsepower rating of 100  
hp (75 kW).  
Figure 1. A-Frame Components  
Operation 9  
MAN0160 (Rev. 2/22/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Hydraulic  
BLADE ANGLE ADJUSTMENT  
The blade may be angled 45 degrees or to any position  
in between, to the right or left by hydraulic remote con-  
trol from the tractor seat.  
CAUTION  
„ Before changing positions of manual swing, tilt,  
or angle positions:  
1. Raise the blade a few inches off the ground by  
operating the lift control lever of the tractor.  
•
Park tractor on level ground, apply parking  
2. Actuate the control valve the angling cylinder is  
brake, level implement boom, shut off tractor,  
and remove key.  
connected to.  
•
Make manual changes slowly and carefully  
3. On tractors with two circuit selector valves, select  
angling circuit and actuate the tractor control valve  
connected to selector valve.  
to prevent hazardous movement of mecha-  
nisms.  
•
become entrapped during adjustment changes  
or if the 3-point hitch suddenly lowers.  
Never stand in positions where you could  
NOTE: Do not operate the selector valve under  
load.  
„ Always secure lock pins with safety pins to pre-  
vent lock pins from bumping out of the positioning  
holes. Failure to do so may result in accidents  
and/or damage to blade.  
1. Hydraulic Angle Arm Assembly  
5. Hyd Cylinder 3.5 x 1.5 x 16  
Mechanical  
5
The blade may be angled 15, 30, 45 and 60 degrees  
for forward grading, and 15 and 30 degrees for backfill-  
ing to right or left from center position without unhook-  
ing the blade from the tractor.  
Swing  
1
1. Raise the blade a few inches off the ground by  
operating the lift control lever of the tractor 3-point  
hitch.  
2. Remove the safety pin (10) and lock pin (2).  
3. Set blade at desired position and replace pins.  
CD5999-1  
Angle  
5
4
Tilt  
Figure 3. Hydraulic Configuration Assembly  
2
REVERSE BLADE  
10  
The blade is reversible without removing it from the  
tractor.  
1. Raise blade off the ground.  
2. Mechanical – Remove the lock pin (2), Figure 2,  
and rotate it counter-clockwise to the desired  
position and replace pins.  
3. Hydraulic – Detach the angling cylinder (7) from  
the hydraulic angle arm (1), Figure 3, and rotate it  
counter-clockwise to the desired position. Attach  
angling cylinder (7) to hydraulic angle arm (1).  
CD5980-1  
2. Lock Pin Assembly  
10. 3/16 Safety Pin  
NOTE: In some cases it may be necessary to offset to  
Figure 2. Mechanical Configuration Assembly  
the right and tip up the right end of the blade to rotate it.  
10 Operation  
MAN0160 (Rev. 2/22/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Hydraulic  
TILT ADJUSTMENT  
The blade may be tilted 22 degrees up or down and to  
any position in between.  
1. Tilt Lock Pin  
To prevent damage to the blade and hydraulic cylinder,  
do not use lock pin (1, Figure 4).  
NOTE: In some cases it may not be possible to fully tilt  
and angle and still be able to raise the blade high  
enough to clear the ground. In this case, use less tilt.  
NOTE: It is possible for the blade to contact other com-  
ponents if the blade is tilted when angled. Operate  
blade slowly when angling blade.  
OFFSET (SWING)  
Mechanical Adjustment  
The blade may be offset 12" (305 mm) and 24" (610  
mm), either side from the center position.  
CD5980-1  
To offset the blade:  
1
1. Park the tractor on level ground.  
2. Apply parking brake and raise blade 2" (51 mm)  
Figure 4. Mechanical Configuration - Tilt  
Mechanical  
above the ground.  
3. Shut off the engine and level the boom.  
The blade may be tilted 15 and 30 degrees up and  
down.  
4. Remove safety pin (10) and lock pin (16), swing  
the boom to the desired position and replace the  
pins.  
To tilt blade:  
1. Remove tilt lock pin (1),  
2. Rotate the blade to the desired position, and  
3. Replace the pin.  
10. 3/16 Safety Pin  
16. Lock Pin  
10  
NOTE: Additional tilting may be obtained by adjusting  
the draft links of the 3-point hitch.  
16  
4. Hyd Cylinder 3.5 x 1.25 x 8  
5. Hyd Cylinder 3.5 x 1.5 x 16  
5
Swing  
1
CD5980-1  
CD5999-1  
Angle  
5
Figure 6. Mechanical Configuration - Offset  
4
Tilt  
Adjustment with Hydraulic Swing Cylinder  
The swing cylinder rotates the boom 30 degrees right  
or left or to any position in between, resulting in a max-  
imum of 24" (610 mm) offset to right or left.  
Figure 5. Hydraulic Configuration - Tilt  
Operation 11  
MAN0160 (Rev. 2/22/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To angle the blade:  
1. Raise blade a few inches above the ground by  
operating the lift control lever of the tractor.  
„ Watch for hidden hazards on the terrain during  
2. Actuate the control valve to which the swing  
operation.  
cylinder is connected.  
„ Before working underneath, read manual  
instructions, securely block up, and check stability.  
Secure blocking prevents equipment from drop-  
ping due to hydraulic leak down, hydraulic system  
failure, or mechanical component failure.  
3. On tractors having two circuit selector valves,  
select swing circuit and actuate tractor control  
valve connected to selector valve.  
NOTE: Do not operate the selector valve under load.  
4. Hyd Cylinder 3.5 x 1.25 x 8  
5. Hyd Cylinder 3.5 x 1.5 x 16  
CAUTION  
„ Stop power unit and equipment immediately  
upon striking an obstruction. Turn off engine,  
remove key, inspect, and repair any damage before  
resuming operation.  
5
Swing  
1
BACKFILLING  
For backfilling ditches or trenches, reverse the blade by  
rotating counter-clockwise and back push.  
LEVELING AND GRADING  
Set the blade to the desired position of offset, angle  
and tilt for leveling and grading.  
CD5999-1  
Angle  
5
PRE-OPERATION CHECK LIST  
(OPERATOR’S RESPONSIBILITY)  
4
Tilt  
___ Review and follow all safety rules and safety  
decal instructions on pages 5 through 8.  
___ Check that equipment is properly and securely  
attached to tractor.  
Figure 7. Hydraulic Configuration - Offset  
___ Check that all safety decals are installed and in  
good condition. Replace if damaged  
OPERATING TIPS  
___ Check that all hardware and cotter pins are prop-  
erly installed and secured.  
___ Check that all lubrication points are greased.  
„ Look down and to the rear and make sure area  
is clear before operating in reverse.  
___ Check that blade cutting edge is in good condi-  
tion.  
„ Do not operate on steep slopes.  
___ Check that all hydraulic hoses and fittings are in  
good condition and not leaking before starting  
tractor. Check that hoses are not twisted, bent  
sharply, kinked, frayed or pulled tight. Replace  
any damaged hoses immediately.  
„ Do not stop, start, or change directions sud-  
denly on slopes.  
„ Use extreme care and reduce ground speed on  
slopes and rough terrain.  
12 Operation  
MAN0160 (Rev. 2/22/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER SERVICE  
LUBRICATION  
Weekly  
„ Keep hands and body away from pressurized  
lines. Use paper or cardboard, not hands or other  
body parts to check for leaks. Wear safety goggles.  
Hydraulic fluid under pressure can easily penetrate  
skin and will cause serious injury or death.  
Oil the pivot pins with SAE 30 oil.  
8 Hours  
Grease optional skid shoes.  
„ Make sure that all operating and service person-  
nel know that if hydraulic fluid penetrates skin, it  
must be surgically removed as soon as possible by  
a doctor familiar with this form of injury or gan-  
grene, serious injury, or death will result. CON-  
TACT A PHYSICIAN IMMEDIATELY IF FLUID  
ENTERS SKIN OR EYES. DO NOT DELAY.  
BOLTS  
1. Check bolts periodically to be sure they are tight.  
2. Replace bolts as needed.  
NOTE: Replacement bolts must have the same  
strength markings on the heads. Refer to bolt torque on  
page 47.  
„ Before working underneath, read manual  
instructions, securely block up, and check stability.  
Secure blocking prevents equipment from drop-  
ping due to hydraulic leak down, hydraulic system  
failure, or mechanical component failure.  
CLEANING  
After Each Use  
„ Never perform service or maintenance with  
engine running.  
●
●
●
Remove large debris such as clumps of dirt, grass,  
crop residue, etc. from machine.  
„ Before dismounting power unit or performing  
any service or maintenance, follow these steps:  
disengage power to equipment, lower the 3-point  
hitch and all raised components to the ground,  
operate valve levers to release any hydraulic pres-  
sure, set parking brake, stop engine, remove key,  
and unfasten seat belt.  
Inspect machine and replace worn or damaged  
parts.  
Replace any safety decals that are missing or not  
readable.  
Periodically or Before Extended Storage  
●
Clean large debris such as clumps of dirt, grass,  
crop residue, etc. from machine.  
„ Keep all persons away from operator control  
area while performing adjustments, service, or  
maintenance.  
●
Remove the remainder using a low-pressure water  
spray.  
1. Be careful when spraying near scratched or torn  
safety decals or near edges of decals as water  
spray can peel decal off surface.  
CAUTION  
2. Be careful when spraying near chipped or  
„ Always wear relatively tight and belted clothing  
to avoid entanglement in moving parts. Wear  
sturdy, rough-soled work shoes and protective  
equipment for eyes, hair, hands, hearing, and head.  
scratched paint as water spray can lift paint.  
3. If a pressure washer is used, follow the advice  
of the pressure washer manufacturer.  
●
●
Inspect machine and replace worn or damaged  
parts.  
BLADE CUTTING EDGE  
To reverse the cutting edge  
1. Remove the 5/8" plow bolts.  
Sand down scratches and the edges of areas of  
missing paint and coat with Woods spray paint of  
matching color (purchase from your Woods  
dealer).  
2. Remove the cutting edge from the moldboard and  
reinstall with the sharp edge down.  
●
Replace any safety decals that are missing or not  
readable (supplied free by your Woods dealer).  
See Safety Decals section for location drawing.  
3. Replace cutting edge when both edges are worn.  
MAN0160 (Rev. 2/22/2006)  
Owner Service 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
CAUTION  
„ Always wear relatively tight and belted cloth-  
ing to avoid entanglement in moving parts. Wear  
sturdy, rough-soled work shoes and protective  
equipment for eyes, hair, hands, hearing, and  
head.  
„ Before dismounting power unit or performing  
any service or maintenance, follow these steps:  
disengage power to equipment, lower the 3-point  
hitch and all raised components to the ground,  
operate valve levers to release any hydraulic  
pressure, set parking brake, stop engine, remove  
key, and unfasten seat belt.  
„ Tighten all bolts, nuts and screws to torque  
chart specifications. Check that all cotter pins are  
installed securely to ensure equipment is in a safe  
condition before putting unit into service.  
„ Before working underneath, read manual  
instructions, securely block up, and check stabil-  
ity. Secure blocking prevents equipment from  
dropping due to hydraulic leak down, hydraulic  
system failure, or mechanical component failure.  
DEALER SET-UP INSTRUCTIONS  
„ Keep all persons away from operator control  
area while performing adjustments, service, or  
maintenance.  
Assembly of this equipment is the responsibility of the  
Woods dealer. It should be delivered to the owner  
completely assembled, lubricated, and adjusted for  
normal operating conditions.  
„ Keep hands and body away from pressurized  
lines. Use paper or cardboard, not hands or other  
body parts to check for leaks. Wear safety gog-  
gles. Hydraulic fluid under pressure can easily  
penetrate skin and will cause serious injury or  
death.  
Assembly will be easier if components are aligned  
and loosely assembled before tightening hardware.  
Recommended torque values for hardware are  
located on page 47.  
„ Make sure that all operating and service per-  
sonnel know that if hydraulic fluid penetrates  
skin, it must be surgically removed as soon as  
possible by a doctor familiar with this form of  
injury or gangrene, serious injury, or death will  
result. CONTACT A PHYSICIAN IMMEDIATELY IF  
FLUID ENTERS SKIN OR EYES. DO NOT DELAY.  
ASSEMBLY TABLE OF CONTENTS  
MAIN ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
MANUAL CONFIGURATION  
OFFSET LINKAGE - MODELS: M & MT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
HYDRAULIC ANGLE KIT - MODELS: MA, SA, TA, AND OPTIONAL KIT 1004870 . . . . . . . . . . 19  
HYDRAULIC TILT KIT - MODELS: MT & TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
HYDRAULIC OFFSET KIT - MODEL: SA AND OPTIONAL KIT 1004872 . . . . . . . . . . . . . . . . . . 22  
HYDRAULIC CONFIGURATION  
MODEL H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
SELECTOR VALVE KIT 1004873 (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
OPTIONAL EQUIPMENT - ALL MODELS  
PNEUMATIC TAIL WHEEL (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
SKID SHOE KIT 18296 (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
END PLATE KIT 22658 (OPTIONAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
PRE-DELIVERY & DELIVERY CHECK LISTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
MAN0160 (Rev. 2/22/2006)  
14 Assembly  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAIN ASSEMBLY - All Models  
Attach Blade to Pivot Assembly  
Assemble the main portion of the blade before start-  
ing on any of the optional configurations.  
1. Place blade assembly (11) on floor with pivot  
attachment pointing up.  
2. Raise the top end approximately 4" (102 mm)  
above the ground with a wooden block. Place pivot  
assembly (9) on blade assembly (11).  
3. Stack two shim washers (53) on each of the four  
holes in blade. Place retainer assembly (10) on wash-  
ers.  
CD5979-2  
4. Place washers (52) and lock washers (51) on  
bolts (50) and insert through retainer (10), washers  
(53), and pivot attachment (9).  
Figure 8. Blade and Pivot Assembly  
5. Secure by placing washers (52) and nuts (54) on  
bolts and torque to 300 lbs.-ft (403 N-m).  
9. Pivot assembly  
51 Washer, Lock 3/4  
10. Retainer assembly  
52. Washer, Flat 3/4 Standard  
53. Washer, Shim .75 x 1.50 x 18ga  
54. Nut, Hex 3/4 NC  
11. RB750 Molboard assembly  
11. RB850 Molboard assembly  
50. Screw, HHCS 3/4 NC x 3 GR5  
Attach Boom to Pivot Assembly  
1. Grease inside of tube on rear of boom (4).  
2. Set blade assembly upright. Place a block of  
wood under pivot assembly to secure.  
Grease Tube  
4
3. Place boom parallel to blade and insert greased  
tube over post of pivot assembly (9). Rotate boom 90  
degrees to lock lip on rear of boom over pivot assem-  
bly.  
Lip  
4. Place jack stand under boom so boom is in a hor-  
izontal position.  
9
4. Boom  
9. Pivot assembly  
CD5979-3  
Figure 9. Boom and Blade Assembled  
MAN0160 (Rev. 2/22/2006)  
Assembly 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Attach A-Frame  
1. A-Frame  
2. Parking Stand Assembly  
22. Pin, Pivot  
1. Position A-frame (1) over end of boom and insert  
pivot pin (22). Secure with cotter pin (40).  
2. Attach parking stand (2) in parking position as  
shown in Figure 10. Secure with clevis pin (45) and  
safety pin (30).  
30. Pin, Safety 3/16  
40. Pin, Cotter 3/8 x 2-1/2  
45. Pin, Clevis 5/8 x 3-3/4  
22  
40  
Parking Position  
20  
31  
Storage Position  
44  
21  
CD5979-4  
CD4311  
1
45  
2
30  
4
CD4312  
Figure 10. A-Frame to Boom Assembly  
Install Manual Tube  
1. Place manual tube (3) over holes on right side of  
A-Frame as shown in Figure 11.  
2. Secure into position using three cap screws (41),  
six flat washers (42), (one on each side), and lock  
nuts (43).  
3. Manual Tube  
41. Cap Screw, 3/8 NC x 1 GR5  
42. Washer, Flat 3/8  
43. Nut, Lock 3/8 NC  
CD5979-6  
Figure 11. Manual Tube Installation  
MAN0160 (Rev. 2/22/2006)  
16 Assembly  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Install Slow Moving Vehicle Sign  
NOTE: If installing optional hydraulic kits that include  
double relief valves on Model SA or the complete  
hydraulic system for Model H, do not install bracket  
(5, Step 1) at this time. Begin with Step 2.  
Refer to Figure 12.  
1. Place bracket (5) to top of boom and secure with  
two carriage bolts (34), flat washers (36), lock wash-  
ers (37), and hex nut (38).  
2. Attach SMV socket (6) to bracket (5) using two  
carriage bolts (34), flat washers (36), lock washers  
(37), and hex nuts (38).  
3. Attach SMV sign (8) to SMV sign bracket (7)  
using two round head screws (32) and nuts (33).  
4. Insert sign and bracket assembly into socket (6)  
to display SMV sign.  
5. Bracket - SMV Sign  
6. Socket, SMV Emblem  
7. SMV Bracket  
8. Slow Moving Vehicle Sign  
32. Screw, Round Head 1/4 NC x 1/2  
33. Nut, Hex 1/4 NC  
CD5979-5  
34  
34. Bolt, Carriage 5/16 NC x 1-1/4  
36. Washer, Flat 5/16 Standard  
37. Washer, Lock 5/16  
Figure 12. Slow Moving Vehicle Sign Installation  
38. Nut, Hex 5/16 NC  
Proceed to page listed below to complete desired blade assembly.  
M = All Manual: Angle, Tilt & Swing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
MT = Manual Swing & Angle: Hydraulic Tilt for tractors with at least one hydraulic port . . 18  
MA = Manual Swing & Tilt: Hydraulic Angle for tractors with at least one hydraulic port . . 19  
SA = Manual Tilt: Hydraulic Swing & Angle for tractors with at least two hydraulic ports . . 19  
TA = Manual Swing: Hydraulic Tilt & Angle for tractors with at least two ports. . . . . . . . . . 19  
H = All Hydraulic: Angle, Tilt & Swing for tractors with three hydraulic ports . . . . . . . . . . 23  
MAN0160 (Rev. 2/22/2006)  
Assembly 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Models: M & MT  
4. Rotate boom to desired position. Install lock pin  
assembly (2) through end of boom and pivot assem-  
bly. Secure with safety pin (10).  
Install Offset Linkage  
1. Model M only - Place boom and pivot assembly to  
desired position. Align holes at bottom of pivot  
assembly and insert tilt lock pin (1) as shown. Rotate  
pin to lock into position.  
5. Insert inner swing link (4) into outer swing link (5).  
6. Attach outer swing link to the A-Frame and insert  
clevis pin (15). Secure with cotter pin (11).  
2. With boom 90 degrees to the blade, place retain-  
ing cap (3) on boom as shown in Figure 13.  
7. Attach inner swing link (4) to the boom and insert  
clevis pin (15). Secure with cotter pin (11).  
3. Install three cap screws (12), lock washers (14),  
and flat washers (13) to secure boom to blade assem-  
bly.  
8. Rotate A-Frame to desired position. Align holes in  
inner and outer swing links and insert lock pin (16).  
Secure with safety pin (10).  
NOTE: For model MT, do not install front cap screw,  
(12) at this time.  
15  
11  
10  
16  
5
4
15  
12  
14  
3
11  
13  
2
1. Tilt lock Pin  
2. Lock Pin Assembly  
3. Retaining Cap  
10  
4. Link, Inner Swing  
5. Link, Outer Swing  
10. Pin, Safety 3/16  
11. Pin, Cotter 1/4 x 1-3/4  
12. Screw, HHCS 3/4 NC x 2-1/4 GR5  
13. Washer, Flat 3/4 SAE  
14. Washer, Lock 3/4  
15. Pin, Clevis 1 x 2-1/2 HT  
16. Pin, Swing Lock  
CD5980-2  
1
Figure 13. Manual Configuration  
NOTE: For Model MT, proceed to page 20 for hydraulic tilt cylinder installation instructions.  
MAN0160 (Rev. 2/22/2006)  
18 Assembly  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Models: MA, SA, & TA or Optional  
Hydraulic Angle Kit 1004870  
Install Hydraulic Angle Cylinder  
5
Refer to Figure 14.  
24  
1. Remove lock pin assembly (2) and safety pin (10)  
from rear of boom, if previously installed. See Figure  
13 on page 18 for lock pin assembly location.  
27  
25  
26  
4
2. Remove hardware and retaining cap (3) from top  
of boom if previously installed. See Figure 13 on page  
18 for retaining cap location.  
7
8
23  
7
22  
3. Place hydraulic angle arm assembly (4) on boom  
as shown Figure 14.  
8
9
4. Secure into position using three cap screws (27),  
lock washers (25), and flat washers (26).  
6
5. Attach hydraulic cylinder (6) to boom and hydrau-  
lic angle arm assembly as shown. Secure with pins  
supplied with the cylinder.  
CD5986  
6. Attach hose holder (5) to A-Frame using carriage  
bolt (24), flat washer (23), and lock nut (22).  
Figure 14. Angle Kit Installation  
7. Install adjustable elbows (7) and hoses (8) (Mod-  
els MA and TA) to cylinder.  
NOTE: Do not install 84” hoses (8) if Hydraulic Offset  
cylinder is to be installed.  
8. Route hoses as shown in Figure 15.  
4. Hyd Angle Arm Assembly  
5. Hyd Hose Holder  
6. Hyd Cylinder 3-1/2 x 16  
7. Elbow, 3/4 ORBM 3/4 JICM 90  
8
Hose, 3/8 84 1/2 NPTM 3/4 JICF  
9. Strap, Binding 14-1/2  
22. Nut, Lock 3/8  
23. Washer, Flat 3/8 Standard  
24. Bolt, Carriage 3/8 NC x 1-1/4 GR1  
25. Washer, Lock 3/4  
CD5998  
26. Washer, Flat 3/4 SAE  
27. Cap Screw, 3/4 NC x 3 GR5  
Figure 15. Angle Kit Hose Routing  
NOTE: For model SA, Proceed to page 22 for hydraulic offset cylinder and relief valve installa-  
tion instructions.  
MAN0160 (Rev. 2/22/2006)  
Assembly 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Models: MT & TA  
Install Hydraulic Tilt Kit 1004871  
Refer to Figure 16  
NOTE: Remove tilt lock pin (1) before installing  
hydraulic tilt kit. See Figure 13 on page 18 for lock pin  
location  
1. Attach hydraulic cylinder (1) to blade assembly  
and pivot assembly as shown. Secure with pins sup-  
plied with the cylinder.  
2. Install adjustable elbows (2) and hoses (6) to cyl-  
inder.  
3. Attach hose holder (4) to A-Frame using carriage  
bolt (18), flat washer (19), and lock nut (20). For mod-  
els with hydraulic angle (TA) proceed to page 21 for  
hose routing.  
CD5985  
4. Attach hose clamp (3) to hose support (5) using  
cap screw (15), lock washer (16), and hex nut (17).  
Do not tighten at this time.  
5. Remove cap screw (21), lock washer (23), and  
flat washer (22) from forward position on retaining cap  
as shown.  
Figure 16. Tilt Kit Installation with Manual  
Angle Control  
6. Position hose support (5) over hole and reinstall  
hardware.  
7. Route hoses as shown in Figure 17.  
8. Position hose support (5) and tighten hardware.  
9. Place hoses in hose clamp (3) and tighten hard-  
ware. Leave adequate slack in hoses to allow for tilt  
and angling of blade.  
1. Hyd Cylinder 3-1/2 x 8  
2. Elbow, 3/4 ORBM 3/4 JICM 90  
3. Hose Clamp 5/8  
4. Hyd Hose Holder  
5. Link, Hose Support  
6
Hose, 3/8 138 1/2 NPTM x 3/4 JICF  
7. Binding Strap 14-1/2  
15. Cap Screw 5/16 NC x 1 GR5  
16. Washer, Lock 5/16  
CD5993  
17. Nut, Hex 5/16 NC  
18. Bolt, Carriage 3/8 NC x 1-1/4 GR5  
19. Washer, Flat 3/8 Standard  
20. Nut, Lock 3/8  
Figure 17. Tilt Kit Hose Routing  
21. Cap Screw 3/4 NC x 2-1/4 GR5  
22. Washer, Flat 3/4 SAE  
23. Washer, Lock 3/4  
MAN0160 (Rev. 2/22/2006)  
20 Assembly  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model: TA  
Install Hydraulic Tilt Kit  
NOTE: If Rear Blade is equipped with hydraulic angle  
cylinder, route tilt kit hydraulic hoses as shown in Fig-  
ure 18.  
CD5996  
Figure 18. Hydraulic Tilt and Angle Kit Hose Routing  
1. Attach hose clamp (3) to boom as shown in Fig-  
ure 19.  
17  
2. Position tape marked on hoses (6) at hose clamp  
(3).  
16  
3
3. Secure hose clamp (3) with cap screw (15), lock  
washer (16), and hex nut (17).  
3. Hose Clamp 5/8  
6. Hose, 3/8 138 1/2 NPTM 3/4 JICF  
(from Tilt cylinder)  
15  
15. Cap Screw 5/16 NC x 1 GR5  
16. Washer, Lock 5/16  
6
17. Nut, Hex 5/16 NC  
CD5996-1  
Figure 19. Hose Clamp Installation  
Assembly 21  
MAN0160 (Rev. 2/22/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model: SA or Optional Offset Kit 1004872  
Install Hydraulic Offset Cylinder  
24  
23  
22  
Refer to Figure 20.  
1
11  
NOTE: Hydraulic angle cylinder must be installed with  
this offset kit.  
5
2
1. Install hydraulic angle kit as instructed on page  
19. Remove 84” hoses from angle cylinder if previ-  
ously installed.  
9
8
10  
4
2. Attach hydraulic cylinder (3) between A-Frame  
and boom as shown in Figure 20. Secure with pins  
supplied with the cylinder.  
3
Offset  
3. Install adjustable elbows (4) to cylinder (3).  
4. Remove bracket (1) and hardware if previously  
installed.  
22  
21  
5. Install 45–degree elbows (5) into relief valves (2).  
Position elbows outward as shown.  
6
Angle  
6. Attach both valve blocks (2) and bracket (1) to  
boom using two cap screws (21), four flat washers  
(22), two lock washers (23), and hex nuts (24).  
7
CD5982  
7. Attach hoses (10) to elbows (5) as shown.  
8. Attach hoses (8 & 9) to back side of relief valves  
(2) and offset cylinder (3) as shown in Figure 21.  
Figure 20. Offset Kit Installation  
9. Attach hoses (6 & 7) to back of relief valves (2)  
and angle cylinder as shown in Figure 21.  
To Tractor  
Offset Couplers  
To Tractor  
Angle Couplers  
1. Bracket - SMV Sign  
2. Valve Double Relief 1600 psi  
3. Hyd Cylinder 3-1/2 x 16  
4. Elbow, 3/4 ORBM 3/4 JICM 90  
5. Elbow, 3/4 JICM x 3/4 ORMB 45  
6. Hose, 3/8 18 3/4 ORBM 3/4 JICF  
7. Hose, 3/8 24 3/4 ORBM 3/4 JICF  
8. Hose, 3/8 28 3/4 ORBM 3/4 JICF  
9. Hose, 3/8 34 3/4 ORBM 3/4 JICF  
10. Hose, 3/8 66 1/2 NPTM 3/4 JICF  
11. Binding Strap, 14-1/2  
D
C
C
D
A
B
A
B
21. Cap Screw, 5/16 NC x 5-1/2 GR5  
22. Washer, Flat 5/16 Standard  
23. Washer, Lock 5/16  
CD5997  
24. Nut, Hex 5/16 NC  
Figure 21. Hose Connection  
MAN0160 (Rev. 2/22/2006)  
22 Assembly  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Model: H  
Install Hydraulic Cylinders  
Refer to Figure 22.  
1. Place hydraulic angle arm (1) on boom as shown.  
5. Attach hydraulic tilt cylinder (4) to pivot assembly  
and blade as shown. Secure with pins supplied with  
the cylinder.  
2. Secure into position using three cap screws (33),  
lock washers (35), and flat washers (34).  
6. Install two adjustable elbows (6) to each of the  
hydraulic cylinders as shown.  
3. Attach hydraulic angle cylinder (5) to boom and  
hydraulic angle arm assembly as shown. Secure with  
pins supplied with the cylinder.  
7. Install two hoses (15) to the hydraulic tilt cylinder.  
4. Attach hydraulic offset cylinder (5) to A-Frame  
and boom as shown. Secure with pins supplied with  
the cylinder.  
NOTE: Do not install angle and offset cylinders hoses  
at this time.  
8. Attach hose holder (9) to back side of A-Frame as  
shown. Secure using one carriage bolt (28), flat  
washer (29), and lock nut (30).  
Offset  
6
9
1. Hyd Angle Arm Assembly  
5
28  
29  
4. Cylinder, Hyd 3-1/2 x 8  
30  
5. Cylinder, Hyd 3-1/2 x 16  
6. Elbow, 3/4 ORBM 3/4 JICM 90  
9. Hyd Hose Holder  
33  
35  
1
34  
15. Hose, 3/8 138 1/2 NPTM 3/4 JICF  
28. Bolt, Carriage 3/8 NC x 1-1/4 GR1  
29. Washer, 3/8 Flat  
30. Nut, Lock 3/8 NC  
33. Screw, HHCS 3/4 NC x 3 GR5  
34. Washer, Flat 3/4 SAE  
35. Washer, Lock 3/4  
6
CD5983-2  
Angle  
5
15  
6
4
Tilt  
Figure 22. Hydraulic Cylinder Installation  
MAN0160 (Rev. 2/22/2006)  
Assembly 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Install Relief Valves and Hoses  
24  
23  
22  
1. Install 45–degree elbows (5) into relief valves (2).  
Position elbows outward as shown in Figure 23.  
1
11  
5
2. Attach both valve blocks (2) and SMV bracket (1)  
to boom using two cap screws (21), four flat washers  
(22), two lock washers (23), and hex nuts (24).  
2
9
3. Attach hoses (10) to elbows (5) as shown.  
8
10  
4. Attach hoses (8 & 9) to back side of relief valves  
4
(2) and offset cylinder (3) as shown.  
5. Attach hoses (6 & 7) to back of relief valves (2)  
and angle cylinder as shown in Figure 23.  
3
Offset  
6. Attach hose clamp (12) to boom as shown in Fig-  
ure 25.  
7. Position tape marked on hoses (20) at hose  
clamp (12).  
22  
21  
6
8. Secure hose clamp (12) with cap screw (30), lock  
washer (23), and hex nut (24).  
Angle  
7
9. Route hoses as shown in Figure 24.  
Figure 23. Relief Valve and Hose Installation  
24  
23  
D
12  
C
C
A
B
D
30  
A
B
20  
Position Clamp  
at Tape Mark  
on Hoses  
11  
CD5994  
CD5996-2  
Figure 24. RB750H/RB850H Hose Routing  
Figure 25. Hose Clamp Installation  
1. Bracket SMV Sign  
12. Clamp, Feedline Hose 5/8  
2. Valve Double Relief 1600 psi  
5. Elbow, Hyd 3/4 JICM x 3/4 ORMB 45°  
6. Hose, 3/8 18 3/4ORBM 3/4 JICF  
7. Hose, 3/8 24 3/4ORBM 3/4 JICF  
8. Hose, 3/8 28 3/4ORBM 3/4 JICF  
9. Hose, 3/8 34 3/4ORBM 3/4 JICF  
10. Hose, 3/8 66 1/2 NPTM 3/4 JICF  
11. Binding Strap, 14-1/2  
20. Hose, 3/8 138 1/2 NPTM 3/4JICF  
(from Tilt cylinder)  
21. Cap Screw, 5/16 NC x 5-1/2 GR5  
22. Washer, Flat 5/16 Standard  
23. Washer, Lock 5/16  
24. Nut, Hex 5/16 NC  
30. Cap Screw, 5/16 NC x 1 GR5  
MAN0160 (Rev. 2/22/2006)  
24 Assembly  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Install Selector Valve Kit 1004873  
(Optional)  
Refer to Figure 26.  
NOTE: Double relief valves must be installed for use  
with this option.  
1. Remove hoses on the tractor side of double relief  
valves. Two of these hoses will be reused to complete  
the selector valve installation.  
2. Remove hose holder (13) and hardware from the  
A-Frame if previously installed during angle kit  
assembly.  
3. Attach double selector valve (2) to valve mount-  
ing bracket (1). Secure with cap screw (26), cap  
screw (27), four flat washers (28), and lock nuts (29).  
CD5987  
NOTE: Cap screw (27) is 3-1/2 inches long and used  
for attaching hose holder (13) to the top of the selec-  
tor valve as shown in Figure 26.  
Figure 26. Selector Valve Kit Installation  
Hose holder can be positioned on either side of the  
selector valve, depending on the location of the trac-  
tor remote couplers.  
4. Attach selector valve and bracket assembly to the  
A-Frame. Secure in place using two carriage bolts  
(25), flat washers (28), and lock nuts (29).  
5. Install four adapter fittings (3) in the side ports of  
the selector valve (2).  
6. Install four 26” hoses (5) between adapter fittings  
(3) in side ports of the selector valve (2) and the relief  
valve (11). See Figure 27 for hose connections.  
7. Install two elbows (4) into the top ports of the  
selector valve.  
8. Install two 66” hoses (9) into elbows (4) on the top  
of the selector valve.  
1. Bracket, Valve Mounting  
2. Valve, Double Selector  
3. Adapter, 3/4 JICF 1-1/16 ORBM  
4. Elbow, 3/4 JICM 1-1/16 ORBM x 90  
5. Hose, 3/8 26 3/4 JICF 3/4 JICF  
Figure 27. Selector Valve Hose Connections  
9. Hose, 3/8 66 1/2 NPTM 3/4 JICF  
(from Hydraulic Offset Configuration)  
26. Cap Screw, 3/8 NC x 3 GR5  
27. Cap Screw, 3/8 NC x 3-1/2 GR5  
28. Washer, Flat 3/8 Standard  
29. Nut, Lock 3/8 NC  
11. Valve, Double Relief 1600 psi  
13. Hyd Hose Holder  
(from Hydraulic Angle Kit)  
25. Bolt, Carriage 3/8 NC x 1 GR5  
MAN0160 (Rev. 2/22/2006)  
Assembly 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Install Selector Valve Kit 1004873  
(Optional) Cont’d  
9. Attach handle kit (1004296) to selector valve.  
CD5991-1  
Figure 28. 1004296 Handle Kit Installed  
10. Route hoses as shown in Figure 29.  
CD5995  
Figure 29. Selector Valve Hose Routing  
MAN0160 (Rev. 2/22/2006)  
26 Assembly  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPTIONAL EQUIPMENT - ALL MODELS  
NOTE: Do not use with Category 2 quick-attach cou-  
plers.  
Install Pneumatic Tailwheel 28775  
(Optional)  
IMPORTANT  
3. Secure into position with top link pin.  
■
When grading with tailwheel attached, do not  
4. Attach bracket (9) to boom assembly with clevis  
pin (10), two flat washers (12) and two cotter pins  
(13). Secure together with cap screw (14).  
attach upper link of tractor 3-point hitch to blade  
without using floating links (2 & 3). Without float-  
ing links, equipment damage may result and void  
warranty.  
5. Attach tailwheel arm (15) and yoke (24) to bracket  
(9) with clevis pin (11), washers (26), and cotter pin  
(13).  
Refer to Figure 30.  
The tailwheel is very helpful for finish grading and lev-  
eling work. The ratchet controls the approximate cut-  
ting height.  
6. Attach ratchet (8) between bracket (9) and tail-  
wheel arm (15). Secure with pins supplied with  
ratchet.  
1. Remove top link of tractor 3-point hitch.  
7. Attach top link to float links (2 & 3) using clevis pin  
(5), two SAE flat washers (6), and cotter pins (7).  
2. Attach float links (2 & 3) and sleeve (4) to inside  
of the top holes of A-Frame. 3/4 dia. welded pin on  
side of float links must face outward and be located  
on the bottom end.  
1
14. Cap Screw, 1/2 NC x  
1-3/4 GR5  
15. Tailwheel Arm Asy  
16. Cap, Dust  
17. O-Ring .09 x 1.56 OD  
18. Bushing, Bronze 1.5  
2. Link, Floating Right  
3. Link, Floating Left  
x 1.63 x 1.50  
4. Sleeve, 1.00 x 1.25 x 1.44  
5. Pin, Clevis 1 x 4-29/32 HT  
6. Washer, Flat 1” SAE  
7. Pin, Cotter 1/4 x 2-1/4  
8. Ratchet  
9. Tailwheel Bracket Asy  
10. Pin, Clevis 3/4 x 12-1/4  
11. Pin, Clevis 1 x 12-1/4  
12. Washer, Flat 3/4 Standard  
13. Pin, Cotter 1/4 x 1-1/2  
19. Grease Fitting, 1/4-28  
Tapered Thread  
20. Grease Fitting, 1/8  
Pipe Thread  
21. Plate, Top Dampener  
22. Disc, Friction 4 x 6.15  
23. Pin, Spirol  
7/16 x 2-1/2  
24. Wheel Yoke Asy  
26. Washer, Flat 1” Std  
Figure 30. Pneumatic Tailwheel Installation  
MAN0160 (Rev. 2/22/2006)  
Assembly 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Install Skid Shoe Kit 18296 (Optional)  
1. Attach the bracket (1) to the blade with four cap  
screws (8) and lock nuts (9) as shown in Figure 31.  
Torque hardware to 85 lbs.-ft (115 N-m).  
4. To raise the cutting edge, place spacer(s) (2) and  
washer(s) (10) under skid shoe bracket (1).  
To lower the cutting edge, place spacer(s) (2) and  
washer(s) (10) on top of skid shoe bracket (1).  
2. Insert skid assembly (3) into tube of bracket (1)  
and secure with klik pin (4).  
NOTE: Before using, make sure that skid shoes  
rotate freely. If not, work them loose to avoid prema-  
ture wear. Rotating shoes will last longer.  
3. The cutting edge height is controlled by adjusting  
the skid shoes with a combination of spacers (2) and  
washers (10).  
Grease at assembly and after every eight hours of  
use.  
A. Skid Shoe Kit  
1. Bracket, Skid Shoe  
(includes item 11)  
2. Sleeve, 1.26 x 1.66 x .75  
3. Skid  
4. Pin, Klik 7/16 x 2  
8. Cap Screw, 1/2 x 1-1/4 GR5  
9. Nut, Flanged Lock 1/2 NC  
10. Washer, Flat 1-1/4 Standard  
Figure 31. Skid Shoe Installation  
MAN0160 (Rev. 2/22/2006)  
28 Assembly  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Install End Plate Kit 22658 (Optional)  
1. Attach end plates (3) to each end of blade assem-  
bly. Use two carriage bolts (4) and flanged lock nuts  
(5) to each plate.  
2. Torque to 85 lbs.-ft (115 N-m).  
3
3. Plate, End  
4. Bolt, Carriage 1/2 NC x 1-1/4 GR5  
5. Nut, Flanged Lock 1/2 NC  
CD5856  
4
5
Figure 32. End Plate Installation  
PRE-DELIVERY CHECK LIST  
(DEALER’S RESPONSIBILITY)  
DELIVERY CHECK LIST  
(DEALER’S RESPONSIBILITY)  
Inspect the equipment thoroughly after assembly to  
ensure it is set up properly before delivering it to the  
customer.  
___ Show customer how to make adjustments.  
___ Point out the safety decals. Explain their mean-  
ing and the need to keep them in place and in  
good condition. Emphasize the increased safety  
hazards when instructions are not followed.  
The following check lists are a reminder of points to  
inspect. Check off each item as it is found satisfactory  
or after proper adjustment is made.  
___ Instruct customer how to lubricate and explain  
importance of lubrication.  
___ Check that all safety decals are installed and in  
good condition. Replace if damaged.  
___ Present Operator's Manual and request that  
customer and all operators read it before oper-  
ating equipment. Point out the manual safety  
rules, explain their meanings and emphasize  
the increased safety hazards that exist when  
safety rules are not followed.  
___ Check all bolts to be sure they are properly  
torqued.  
___ Check that all cotter pins and safety pins are  
properly installed. Replace if damaged.  
___ Check and grease all lubrication points.  
___ Explain to customer that when equipment is  
transported on a road or highway, a Slow Mov-  
ing Vehicle (SMV) sign should be used to pro-  
vide adequate warning to operators of other  
vehicles.  
MAN0160 (Rev. 2/22/2006)  
Assembly 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
MAN0160 (Rev. 2/22/2006)  
30 Assembly  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS INDEX  
REAR BLADES  
RB750-4 RB750-4H  
RB850-4 RB850-4H  
MAIN ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 - 33  
MODELS: M & MT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
MODELS: MA, SA, & TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
MODEL: H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 - 37  
HYDRAULIC TILT KIT 1004871 FOR MODELS: MT & TA. . . . . . . . . . 38  
HYDRAULIC OFFSET KIT 1004872 FOR MODEL: SA . . . . . . . . . . . . 39  
HYDRAULIC ANGLE KIT 1004870. . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
SELECTOR VALVE KIT 1004873. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
SELECTOR VALVE 1004261 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
RELIEF VALVE 1004260 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
HYDRAULIC CYLINDER ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . 43  
PNEUMATIC TAILWHEEL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . 44  
WHEEL HUB, TIRE & WHEEL ASSEMBLY. . . . . . . . . . . . . . . . . . . . . 45  
SKID SHOE KIT 18296. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46  
END PLATE KIT 22658. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46  
MAN0160 (Rev. 2/22/2006)  
Parts 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RB750-4 RB850-4 MAIN ASSEMBLY  
40  
22  
41  
42  
33  
20 23  
31  
7
3
8
43  
37  
44  
21  
32  
24  
6
34  
5
1
45  
2
30  
CD5979  
34  
4
54  
52  
13 - COMPLETE DECAL SET  
14 - SAFETY DECAL SET  
46  
47  
53  
9
52  
48  
12  
51  
50  
11  
48  
10  
MAN0160 (Rev. 2/22/2006)  
32 Parts  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RB750-4 RB850-4 MAIN ASSEMBLY PARTS LIST  
REF PART QTY  
DESCRIPTION  
A-Frame with Decals  
REF PART QTY  
DESCRIPTION  
* 3/16 Safety Pin  
1
2
1005001  
28418  
1
1
1
1
1
1
1
1
1
1
1
30  
31  
32  
33  
34  
36  
37  
38  
40  
41  
42  
43  
44  
45  
46  
47  
48  
50  
51  
52  
53  
54  
18270  
923  
1
4
2
2
4
4
4
4
1
3
6
3
2
1
2
6
8
4
4
8
8
4
Parking Stand Assembly  
Manual Tube  
* 1/4 x 1-3/4 Cotter Pin  
* Screw, 1/4 NC x 1/2  
* Nut, 1/4 NC  
3
1003828  
1005002  
1004262  
62484  
1282  
5288  
14458  
4378  
2472  
4529  
744  
4
Boom with Decals  
Bracket - SMV Sign  
Socket SMV Emblem  
SMV Bracket  
5
* Bolt, Carriage 5/16 NC x 1-1/4  
* Washer, 5/16 Flat  
6
7
1004251  
24611  
* Washer, 5/16 Lock  
8
Slow Moving Vehicle Sign  
Pivot Assembly  
* Nut, Hex 5/16 NC GR5  
* 3/8 x 2-1/2 Cotter Pin  
* Cap screw, 3/8 NC x 1 GR5  
* Washer, 3/8 Flat  
9
28363  
10  
27549  
Retainer Assembly  
RB750-4 Moldboard Assembly  
or  
839  
11 1004857  
565  
6698  
27542  
8099  
26920  
21261  
6239  
14334  
2522  
1257  
11036  
1450  
* Nut, Lock 3/8 NC  
11 1004858  
1
1
RB850-4 Moldboard Assembly  
Edge, Cutting .50 x 6.0 x 83  
or  
7/16 x 11/32 Klik Pin HT  
Pin, Clevis 5/8 x 3-3/4 HT  
Bolt, Plow 5/8 NC x 1-3/4 GR5  
Bolt, 5/8 NC x 2.0 Plow GR8  
* Nut, Lock 5/8 NC  
12  
12  
25263  
25270  
1
1
1
1
2
1
1
2
Edge, Cutting .50 x 6.0 x 95  
Decal Set - Complete  
Decal Set - Safety  
Pin, Clevis 1 x 4-29/32 HT  
Hitch Pin 1-1/8  
13 1004298  
14 1005003  
* Cap screw, 3/4 NC x 3 GR5  
* Washer, 3/4 Lock  
20  
21  
26148  
27573  
27546  
14695  
26100  
* Washer, 3/4 Flat  
22  
Pivot Pin  
Washer, 3/4 x 1-1/2 x 18 ga  
* Nut, Hex 3/4 NC  
23†  
24†  
Sleeve, 1 x 1-1/4 x 2  
Sleeve, 1-1/8 x 1-7/16 x 2-5/8  
*
Standard Hardware, Obtain Locally  
†
Optional sleeves for Category 2  
Quick Hitch and Category 3 three  
point hitch; order bushing kit 18295  
MAN0160 (Rev. 2/22/2006)  
Parts 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RB750-4 RB850-4 - MODELS: M & MT  
REF PART QTY  
DESCRIPTION  
REF PART QTY  
DESCRIPTION  
1
2
27543  
27544  
28360  
27552  
27555  
18270  
1
1
1
1
1
2
Tilt Lock Pin  
11  
12  
13  
14  
15  
16  
923  
13759  
2864  
2
3
3
3
2
1
* 1/4 x 1-3/4 Cotter Pin  
* Cap Screw, 3/4 NC x 2-1/4 GR5  
* Washer, 3/4 SAE Flat  
* Washer, 3/4 Lock  
Lock Pin Assembly  
Retaining Cap  
3
4
Swing Link Inner  
Swing Link Outer  
* 3/16 Safety Pin  
2522  
5
8341  
Pin, Clevis 1 x 2-1/2 HT  
Lock Pin  
10  
26446  
*
Standard Hardware, Obtain Locally  
For Model MT proceed to page 38 for Hydraulic Tilt Kit Parts List.  
MAN0160 (Rev. 2/22/2006)  
34 Parts  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RB750-4 RB850-4 MODELS: MA, SA, & TA  
20  
28  
3
21  
24  
5
2
4
28  
27  
1
25  
26  
20  
7
8
23  
22  
8
7
9
6
10  
CD5981  
REF PART QTY  
DESCRIPTION  
REF PART QTY  
DESCRIPTION  
1
2
27599  
27552  
1
1
1
1
1
1
2
2
3
1
Hydraulic Angle Arm Assembly  
Swing Link, Inner  
20  
21  
22  
23  
24  
25  
26  
27  
28  
923  
18270  
6698  
565  
4
2
1
1
1
3
3
3
2
*
* 1/4 x 1-3/4 Cotter Pin  
* 3/16 Safety Pin  
3
26446  
Lock Pin  
* Nut, Lock 3/8 NC  
4
27555  
Swing Link, Outer  
* Washer, 3/8 Flat  
5
3443  
Hyd Hose Holder  
24890  
2522  
2864  
14334  
8341  
* Bolt, Carriage 3/8 NC x 1-1/4 GR1  
* Washer, 3/4 Lock  
6
1003198  
316004  
1004284  
8641  
Hyd Cylinder 3.5 x 1.50 x 16.0  
Elbow, 3/4 ORBM 3/4 JICM 90°  
Hose, 3/8 84 1/2 NPTM 3/4 JICF  
* Binding Strap, 14-1/2  
Tilt Lock Pin  
7
* Washer, 3/4 SAE Flat  
* Cap Screw, 3/4 NC x 3 GR5  
Pin Clevis, 1 x 2-1/2 HT  
Standard Hardware, Obtain Locally  
8
9
10  
27543  
For Model TA proceed to page 38 for Hydraulic Tilt Kit Parts list.  
For Model SA proceed To page 39 For Hydraulic Offset Parts List.  
MAN0160 (Rev. 2/22/2006)  
Parts 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RB750-4 RB850-4 MODEL: H  
24  
23  
22  
2
3
7
14  
13  
16  
12  
6
28  
9
33  
5
35  
34  
24  
23  
8
1
29  
30  
6
22  
21  
10  
20  
11  
CD5983  
5
4
6
15  
MAN0160 (Rev. 2/22/2006)  
36 Parts  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RB750-4 RB850-4 MODEL: H - PARTS LIST  
REF PART QTY  
DESCRIPTION  
REF PART QTY  
DESCRIPTION  
1
2
27599  
1004262  
1004260  
1003196  
1003198  
316004  
1004288  
56  
1
1
2
1
2
6
4
1
1
1
1
1
1
Hyd Angle Arm Assembly  
14 1004283  
15 1004285  
4
2
6
1
2
4
5
5
1
1
1
3
3
3
Hose, 3/8 66 1/2 NPTM 3/4 JICF  
Hose, 3/8 138 1/2 NPTM 3/4 JICF  
* Binding Strap, 14-1/2  
Bracket - SMV Sign (From Main Asy)  
Valve Double Relief 1600psi  
Hyd Cylinder 3.5 x 1.25 x 8.0  
Hyd Cylinder 3.5 x 1.50 x 16.0  
Elbow, 3/4 ORBM 3/4 JICM 90°  
Elbow, 3/4 ORBM 3/4 JICM 45°  
Hose Clamp 5/8  
3
16  
20  
21  
22  
23  
24  
28  
29  
30  
33  
34  
35  
8641  
14562  
300107  
4378  
4
* Cap Screw, 5/16 NC x 1 GR5  
* Cap Screw, 5/16 NC x 5-1/2 GR5  
* Washer, 5/16 Flat  
5
6
7
2472  
* Washer, 5/16 Lock  
8
4529  
* Nut, Hex 5/16 NC GR5  
* Bolt, Carriage 3/8 NC x 1-1/4 GR1  
* Washer, 3/8 Flat  
9
3443  
Hyd Hose Holder  
24890  
565  
10  
11  
360181  
360203  
Hose, 3/8 18 3/4 ORBM 3/4 JICF  
Hose, 3/8 24 3/4ORBM 3/4 JICF  
Hose, 3/8 28 3/4 ORBM 3/4 JICF  
Hose, 3/8 34 3/4 ORBM 3/4 JICF  
6698  
* Nut, Lock 3/8 NC  
12 1004286  
13 1004287  
14334  
2864  
* Cap Screw, 3/4 NC x 3 GR5  
* Washer, 3/4 SAE Flat  
2522  
* Washer, 3/4 Lock  
*
Standard Hardware, Obtain Locally  
MAN0160 (Rev. 2/22/2006)  
Parts 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RB750-4 RB850-4 HYDRAULIC TILT KIT 1004871  
FOR MODELS: MT & TA  
21  
23  
22  
18  
4
17  
16  
3
19  
20  
5
15  
7
CD5985  
1
2
6
REF PART QTY  
DESCRIPTION  
DESCRIPTION  
REF PART QTY  
18  
24890  
1
1
1
3
3
3
* Bolt, Carriage 3/8 NC x 1-1/4 GR1  
* Washer, 3/8 Flat  
1
2
3
4
1003196  
316004  
56  
1
2
1
1
1
2
3
1
5
5
Hyd Cylinder 3.5 x 1.25 x 8.0  
Elbow, 3/4 ORBM 3/4 JICM 90°  
Hose Clamp 5/8  
19  
565  
20  
6698  
13759  
2864  
2522  
* Nut, Lock 3/8 NC  
21#  
22#  
23#  
* Cap Screw, 3/4 NC x 2-1/4 GR5  
* Washer, 3/4 SAE Flat  
* Washer, 3/4 Lock  
3443  
Hyd Hose Holder  
5† 1004832  
Link - Hose Support  
6
1004285  
8641  
Hose, 3/8 138 1/2 NPTM 3/4 JICF  
* Binding Strap, 14-1/2  
* Cap Screw, 5/16 NC x 1 GR5  
* Washer, 5/16 Lock  
7
*
Standard Hardware, Obtain Locally  
15  
16  
17  
14562  
2472  
† Not used if blade has hydraulic angle option.  
4529  
* Nut, Hex 5/16 NC GR5  
# Not included in this kit; from blade with mechanical  
angle adjustment configuration.  
MAN0160 (Rev. 2/22/2006)  
38 Parts  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RB750-4 RB850-4 HYDRAULIC OFFSET KIT 1004872  
FOR MODEL: SA  
24  
23  
1
22  
11  
2
5
9
10  
8
4
3
OFFSET  
22  
21  
6
7
ANGLE  
CD5982  
REF PART QTY  
DESCRIPTION  
REF PART QTY  
DESCRIPTION  
1
2
1004262  
1004260  
1
2
1
6
4
1
1
1
1
Bracket - SMV Sign (From Main Asy)  
Valve Double Relief 1600psi  
10 1004283  
4
6
2
2
2
2
Hose, 3/8 66 1/2 NPTM 3/4 JICF  
11  
8641  
300107  
4378  
* Binding Strap, 14-1/2  
* Cap Screw, 5/16 NC x 5-1/2 GR5  
* Washer, 5/16 Flat  
3# 1003198  
Hyd Cylinder 3.5 x 1.50 x 16.0  
Elbow, 3/4 ORBM 3/4 JICM 90°  
Elbow, 3/4 ORBM 3/4 JICM 45°  
Hose, 3/8 18 3/4 ORBM 3/4 JICF  
Hose, 3/8 24 3/4 ORBM 3/4 JICF  
Hose, 3/8 28 3/4 ORBM 3/4 JICF  
Hose, 3/8 34 3/4 ORBM 3/4 JICF  
21  
4#  
5
316004  
1004288  
360181  
22#  
23#  
24#  
2472  
* Washer, 5/16 Lock  
6
4529  
* Nut, Hex 5/16 NC GR5  
7
360203  
8
1004286  
1004287  
*
Standard Hardware, Obtain Locally  
9
# Quantity shown is for this kit. Additional items come  
from Model MA or Hydraulic Angle Kit 1004870.  
MAN0160 (Rev. 2/22/2006)  
Parts 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HYDRAULIC ANGLE KIT 1004870  
5
24  
27  
4
25  
26  
7
23  
22  
8
8
7
9
6
CD5986  
REF PART QTY  
DESCRIPTION  
REF PART QTY  
DESCRIPTION  
* Nut, Lock 3/8 NC  
4
5
6
7
8
9
27599  
3443  
1
1
1
2
2
3
Hyd Angle Arm Assembly  
Hyd Hose Holder  
22  
23  
24  
25  
26  
27  
6698  
565  
1
1
1
3
3
3
* Washer, 3/8 Flat  
1003198  
316004  
1004284  
8641  
Hyd Cylinder 3.5 x 1.50 x 16.0  
Elbow, 3/4 ORBM 3/4 JICM 90°  
Hose 3/8 84 1/2 NPTM 3/4 JICF  
24890  
2522  
2864  
14334  
* Bolt, Carriage 3/8 NC x 1-1/4 GR1  
* Washer, 3/4 Lock  
* Washer, 3/4 SAE Flat  
* Cap Screw, 3/4 NC x 3 GR5  
* Binding Strap, 14-1/2  
*
Standard Hardware, Obtain Locally  
MAN0160 (Rev. 2/22/2006)  
40 Parts  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SELECTOR VALVE KIT 1004873  
12  
REF PART QTY  
DESCRIPTION  
REF PART QTY  
DESCRIPTION  
1
2
3
4
5
6
27598  
1004261  
316017  
37501  
1
1
4
2
4
3
2
1
2
4
1
Valve, Mounting Bracket  
Valve, Double Selector  
20#  
21#  
22#  
23#  
25  
300107  
4378  
2472  
4529  
6697  
7747  
31138  
565  
2
4
5
5
2
1
1
1
1
* Cap Screw, 5/16 NC x 5-1/2 GR5  
* Washer, 5/16 Flat  
Adapter, 3/4 JICM 1-1/16 ORBM  
* Washer, 5/16 Lock  
Elbow, 3/4 JICM 1-1/16 ORBM x 90°  
Hose, 3/8 26 3/4 JICF 3/4 JICF  
* Nut, Hex 5/16 NC GR5  
* Bolt, Carriage 3/8 NC x 1 GR5  
* Cap Screw, 3/8 NC x 3 GR5  
* Cap Screw, 3/8 NC x 3-1/2 GR5  
* Washer, 3/8 Flat  
1004281  
8641  
* Binding Strap, 14-1/2  
26  
9# 1004283  
10# 1004262  
11# 1004260  
12# 1004288  
Hose, 3/8 66 1/2 NPTM 3/4 JICF  
Bracket - SMV Sign  
27  
28  
Valve, Double Relief 1600psi  
Elbow, 3/4 ORBM 3/4 JICM 45°  
Hyd Hose Holder  
29  
6698  
* Nut, Lock 3/8 NC  
13#  
3443  
*
Standard Hardware, Obtain Locally  
# Not included in this kit. Included in Hydraulic Angle  
and Offset configuration.  
MAN0160 (Rev. 2/22/2006)  
Parts 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SELECTOR VALVE 1004261  
RELIEF VALVE 1004260  
3
4
A
Relief Valve  
Cartridge 1600 psi  
CD5991  
REF  
PART  
QTY  
DESCRIPTION  
A
1
2
1004261  
1004295  
1004296  
Valve, Double Selector  
1
1
Seal kit, Double Selector Valve  
Kit, Selector Valve Handle  
3
4
1004260  
1004297  
1
1
Valve, Hyd Double Relief 1600 psi  
Relief Valve Cartridge, 1600 psi  
MAN0160 (Rev. 2/22/2006)  
42 Parts  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HYDRAULIC CYLINDER ASSEMBLY & PARTS LIST  
25 - Seal Kit 3-1/2 Hyd Cylinder  
(Includes items A throughout G)  
CD5990  
REF  
PART  
QTY  
DESCRIPTION  
REF  
PART  
QTY  
DESCRIPTION  
Nut, Hex 5/8 UNF  
1003196  
1003198  
Cylinder, Hyd 3-1/2 x 8 (Tilt)  
18  
302176  
8
(Torque to 160 lbs.-ft.)  
Cylinder, Hyd 3-1/2 x 16  
(Angle - Offset)  
19  
20  
1631  
2
1
Pin, Clevis  
1
2
3
4
N/S  
N/S  
1
1
1
1
Clevis Cap  
34323  
Nut, Lock 1-14 UNS  
(Torque to 300 lbs.-ft.)  
Rod Cap  
25  
1005000  
Seal Kit (Includes items A - G)  
1004826  
1004829  
Piston, 3.50 OD  
Rod, 1.25 OD (for 1003196)  
or  
A
B
C
D
E
F
2
1
1
1
1
2
2
O-Ring  
Rod Wiper  
4
5
1004830  
N/S  
1
1
4
1
1
1
Rod, 1.50 OD (for 1003198)  
Tube  
O-Ring (Piston Seal Expander)  
Rod Seal  
6
N/S  
Tie Rod  
Piston Seal  
7
1004827  
N/S  
Rod, Clevis  
Piston Wear Ring  
Backup Washer  
15  
17  
Nylon Thread Patch  
G
* Screw, Set 3/8 NC x 1/2  
(Torque to 20 lbs.-ft.)  
*
Standard Hardware, Obtain Locally  
N/S Not Serviced Separately  
MAN0160 (Rev. 2/22/2006)  
Parts 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PNEUMATIC TAILWHEEL ASSEMBLY  
1
REF  
PART  
28775  
QTY  
DESCRIPTION  
REF  
PART  
28776  
QTY  
DESCRIPTION  
1
2
1
1
1
1
1
2
2
1
1
1
1
2
4
1
Tailwheel, Pneumatic Complete  
Link, Floating Right  
15  
16  
17  
18  
19  
1
1
1
2
1
Tailwheel Arm Assembly  
Cap, Dust  
29030  
29031  
29034  
26148  
1863  
12881  
12889  
11011  
1972  
3
LInk, Floating Left  
O-Ring .09 x 1.56 OD  
Bushing, Bronze 1.5 x 1.63 x 1.50  
4
Sleeve, 1.00 x1.25 x 1.44  
Pin, Clevis 1 x 4-29/32 HT  
* Washer, Flat 1” SAE  
* Pin, Cotter 1/4 x 2-1/4  
Ratchet  
5
* Grease Fitting, 1/4-28  
Tapered Thread  
6
20  
21  
22  
23  
24  
25  
26  
195  
14135  
19459  
7276  
1
1
1
1
1
1
2
* Grease Fitting, 1/8 Pipe Thread  
Plate, Top Dampener  
7
6185  
8
1005020  
28781  
28788  
28789  
1257  
Disc, Friction 4 x 6.15  
9
Tailwheel Bracket Assembly  
Pin, Clevis 3/4 x12-1/4  
Pin, Clevis 1 x 12-1/4  
* Pin, Spirol 7/16 x 2-1/2  
Wheel Yoke Assembly  
Tire, Wheel & Hub  
10  
11  
12  
13  
14  
14125  
———  
832  
* Washer, Flat 3/4 Standard  
* Pin, Cotter 1/4 x 1-1/2  
* Cap Screw, 1/2 NC x 1-3/4 GR5  
* Washer, Flat 1” Standard  
1285  
24576  
*
Standard Hardware, Obtain  
Locally  
MAN0160 (Rev. 2/22/2006)  
44 Parts  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WHEEL HUB, TIRE & WHEEL ASSEMBLY  
REF  
PART  
14130  
QTY  
DESCRIPTION  
REF PART QTY  
DESCRIPTION  
1
2
3
4
5
6
1
1
1
1
1
1
Wheel Hub & Axle Assembly  
Nut, Hex 1-14 UNS  
10  
11  
12  
13  
14  
15  
16  
17  
18  
1257  
5849  
14133  
N/S  
2
1
1
1
1
1
1
1
5
* Washer, Flat 3/4 Standard  
Nut, Slotted Hex 3/4 NF  
Hub Cap Assembly w/fitting  
* Grease Fitting, 1/4 Tapered Thread  
Wheel & Tire 18 x 9.5 - 8  
Rim 18 x 9.5 x 8  
3626  
1863  
14131  
1266  
314  
* Washer, Flat 1” SAE  
Axle Assembly  
* Pin, Cotter 3/16 x 1-1/2  
14255  
N/S  
Seal, 1.50 x 2.44 x .31 (Note:  
Point spring-loaded lip outward  
in assembly of seal to housing)  
N/S  
Tire, Rib 18 x 9.5 x 8 6-ply  
Inner Tube, 18 x 9.50 x 8  
Bolt, Wheel 1/2 NF x 1-1/8  
N/S  
7
8
9
2303  
2305  
2
2
1
Bearing Cone  
1258  
Bearing Cup  
14132  
Wheel Hub, Housing w/cups  
N/S  
*
Not Serviced Separately  
Standard Hardware, Obtain Locally  
MAN0160 (Rev. 2/22/2006)  
Parts 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SKID SHOE KIT 18296  
REF  
PART  
18296  
QTY  
DESCRIPTION  
Skid Shoe Kit  
A
–
(includes items 1 thru 11)  
1
2
2
4
2
2
*
27587  
52854  
27586  
27542  
6100  
Bracket, Skid Shoe  
Sleeve, 1.26 x 1.66 x .75  
Skid & shaft assembly  
3
4
Pin, Klik 7/16 x 2  
8
Cap Screw, 1/2 x 1-1/4 GR5  
Nut, Flanged Lock 1/2 NC  
Washer, Flat 1-1/4 Standard  
9
–
*
11900  
7163  
10  
11  
*
1972  
Grease Fitting, 1/4-28  
Tapered Thread  
*
Standard Hardware, Obtain Locally  
END PLATE KIT 22658  
REF  
PART  
QTY  
DESCRIPTION  
3
4
5
N/S  
2615  
Plate, End  
*
Bolt, Carriage 1/2 NC x 1-1/4 GR5  
Nut, Flanged Lock 1/2 NC  
3
11900  
N/S Not Serviced Separately  
Standard Hardware, Obtain Locally  
*
CD5856  
4
5
MAN0160 (Rev. 2/22/2006)  
46 Parts  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BOLT TORQUE CHART  
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific  
application.  
Fasteners must always be replaced with the same grade as specified in the manual parts list.  
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.  
Make sure fastener threads are clean and you start thread engagement properly.  
All torque values are given to specifications used on hardware defined by SAE J1701 MAR99 & J1701M JUL96.  
SAE Bolt Head  
Identification  
SAE SERIES  
TORQUE  
CHART  
A
SAE Grade 2  
(No Dashes)  
SAE Grade 8  
(6 Radial Dashes)  
SAE Grade 5  
(3 Radial Dashes)  
MARKING ON HEAD  
A
SAE 2  
SAE 5  
SAE 8  
Diameter  
(Inches)  
Wrench  
Size  
lbs-ft  
N-m  
8
lbs-ft  
10  
N-m  
13  
lbs-ft  
14  
N-m  
18  
1/4"  
5/16"  
3/8"  
7/16"  
1/2"  
9/16"  
5/8"  
3/4"  
7/8"  
1"  
7/16"  
1/2"  
6
12  
17  
19  
26  
27  
37  
9/16"  
5/8"  
23  
31  
35  
47  
49  
67  
36  
48  
55  
75  
78  
106  
163  
232  
325  
569  
907  
3/4"  
55  
75  
85  
115  
164  
230  
403  
642  
979  
120  
171  
240  
420  
669  
13/16"  
15/16"  
1-1/8"  
1-5/16"  
1-1/2"  
78  
106  
149  
261  
416  
634  
121  
170  
297  
474  
722  
110  
192  
306  
467  
1020  
1383  
METRIC SERIES  
TORQUE  
CHART  
8.8  
Metric Bolt Head  
Identification  
10.9  
A
Metric  
Grade 8.8  
Metric  
Grade 10.9  
COARSE THREAD  
MARKING ON HEAD  
Metric 8.8 Metric 10.9  
N-m lbs-ft  
FINE THREAD  
MARKING ON HEAD  
Metric 8.8 Metric 10.9  
N-m lbs-ft  
A
A
Diameter &  
Thread Pitch Wrench  
(Millimeters)  
Diameter &  
Thread Pitch  
(Millimeters)  
Size  
N-m  
lbs-ft  
6
N-m  
lbs-ft  
6
6 x 1.0  
10 mm  
13 mm  
16 mm  
18 mm  
21 mm  
24 mm  
27 mm  
30 mm  
34 mm  
36 mm  
46 mm  
8
11  
27  
8
8
21  
11  
29  
8
6 x 1.0  
8 x 1.0  
8 x 1.25  
10 x 1.5  
12 x 1.75  
14 x 2.0  
16 x 2.0  
18 x 2.5  
20 x 2.5  
22 x 2.5  
24 x 3.0  
30 x 3.0  
20  
15  
20  
16  
22  
39  
29  
54  
40  
41  
30  
57  
42  
10 x 1.25  
12 x 1.25  
14 x 1.5  
16 x 1.5  
18 x 1.5  
20 x 1.5  
22 x 1.5  
24 x 2.0  
30 x 2.0  
68  
50  
94  
70  
75  
55  
103  
163  
250  
363  
507  
684  
861  
1740  
76  
109  
169  
234  
330  
451  
571  
1175  
80  
151  
234  
323  
457  
623  
790  
1626  
111  
173  
239  
337  
460  
583  
1199  
118  
181  
263  
367  
495  
623  
1258  
87  
120  
184  
268  
374  
505  
635  
1283  
125  
172  
244  
332  
421  
867  
133  
194  
270  
365  
459  
928  
Typical Washer Installations  
Flat Washer  
Lock Washer  
Bolt  
8/9/00  
Nut  
Appendix 47  
Bolt Torque & Size Charts (Rev. 8/14/2002)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BOLT SIZE CHART  
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.  
SAE Bolt Thread Sizes  
5/16  
3/8  
1/2  
5/8  
3/4  
7/8  
IN  
1
2
3
4
5
6
7
MM  
25  
50  
75  
100  
125  
150  
175  
Metric Bolt Thread Sizes  
8MM 10MM  
12MM  
14MM  
16MM  
18MM  
ABBREVIATIONS  
AG............................................................. Agriculture  
ATF ..............................Automatic Transmission Fluid  
BSPP ...........................British Standard Pipe Parallel  
BSPTM ..............British Standard Pipe Tapered Male  
CV...................................................Constant Velocity  
CCW ............................................ Counter-Clockwise  
CW............................................................. Clockwise  
F......................................................................Female  
GA....................................................................Gauge  
GR (5, etc.) ......................................... Grade (5, etc.)  
HHCS.......................................Hex Head Cap Screw  
HT..........................................................Heat-Treated  
JIC ...............Joint Industry Council 37° Degree Flare  
LH ...............................................................Left Hand  
LT......................................................................... Left  
m....................................................................... Meter  
mm.............................................................. Millimeter  
M.........................................................................Male  
MPa........................................................Mega Pascal  
N .................................................................... Newton  
NC.....................................................National Coarse  
NF......................................................... National Fine  
NPSM .................. National Pipe Straight Mechanical  
NPT.........................................National Pipe Tapered  
NPT SWF........National Pipe Tapered Swivel Female  
ORBM.........................................O-Ring Boss - Male  
P ........................................................................ Pitch  
PBY..................................................... Power-Beyond  
psi ........................................Pounds per Square Inch  
PTO.................................................... Power Take Off  
QD ................................................. Quick Disconnect  
RH............................................................ Right Hand  
ROPS..........................Roll-Over Protective Structure  
RPM.......................................Revolutions Per Minute  
RT ......................................................................Right  
SAE.........................Society of Automotive Engineers  
UNC....................................................Unified Coarse  
UNF ........................................................ Unified Fine  
UNS ................................................... Unified Special  
48 Appendix  
Bolt Torque & Size Charts (Rev. 8/14/2002)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY  
(All Models Except Mow’n MachineTM Zero-Turn Mowers and Woods BoundaryTM Utility Vehicles)  
Please Enter Information Below and Save for Future Reference.  
Date Purchased: __________________________  
Model Number: __________________________  
From (Dealer):________________________________________  
Serial Number:________________________________________  
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise  
set forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF  
THE PRODUCT TO THE ORIGINAL PURCHASER.  
The warranty periods for certain gearboxes and blade spindles are listed below:  
Model No.  
Part Warranted  
Duration  
PHD25, PHD35, PHD65, PHD95, 1260, 2162, 3240, BB48, BB60, BB72, BB84,  
BB600, BB720, BB840, BB6000, BB7200, BB8400, BW180-2, BW1800, DS96,  
DS120, RCC42, RM550-2, RM660-2, RM990-3, PRD6000, PRD7200,  
PRD8400, 7144RD-2, 9180RD-2, 9204RD-2  
Gearbox  
components  
5 years from the date of delivery to  
the original purchaser.  
Gearbox  
components  
3 years from the date of delivery to  
the original purchaser.  
RDC54, RD60, RD72  
1 year from the date of delivery to  
the original purchaser if used in  
rental or commercial applications.  
Gearbox  
components  
RDC54, RD60, RD72  
3 years from the date of delivery to  
the original purchaser.  
RM550-2, RM660-2, RM990-3, PRD6000, PRD7200, PRD8400  
Blade spindles  
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to  
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been  
materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized  
service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs  
made with parts other than those obtainable through WOODS.  
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this  
product to a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this  
Warranty.  
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by  
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.  
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if  
WOODS, in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to  
WOODS with proof of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been  
discovered, routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid.  
WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the product. THERE ARE NO  
OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND  
EXCLUSIVE REMEDY UNDER THIS WARRANTY.  
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY.  
WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED  
WARRANTY OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the  
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other  
legal theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits,  
business, revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor,  
supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.  
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture  
replacement parts.  
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation,  
WOODS, its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.  
Answers to any questions regarding warranty service and locations may be obtained by contacting:  
Woods Equipment  
Company  
2606 South Illinois Route 2  
Post Office Box 1000  
Oregon, Illinois 61061  
800-319-6637 tel  
800-399-6637 fax  
www.WoodsEquipment.com  
F-3079 (Rev. 3/21/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY  
(Replacement Parts For All Models Except Mow’n Machine  
Zero-Turn Mowers and Woods Boundary Utility Vehicles)  
TM  
TM  
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and  
workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser  
with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months.  
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of  
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This Warranty  
does not cover normal wear or tear, or normal maintenance items.  
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or  
otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser in any  
way. There are no third party beneficiaries of this Warranty.  
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of  
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with this  
Warranty. The product must be returned to WOODS with proof of purchase within thirty (30) days after  
such defect or noncompliance is discovered or should have been discovered, routed through the dealer and  
distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete  
such repair or replacement within a reasonable time after WOODS receives the product. THERE ARE NO  
OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE  
SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.  
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS  
WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS  
SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/OR ANY  
IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly  
or indirectly from the product, whether such claim is based upon breach of contract, breach of warranty,  
negligence, strict liability in tort or any other legal theory. Without limiting the generality of the foregoing,  
Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or goodwill; (ii) loss of  
crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute  
machinery or rental; or (v) any other type of damage to property or economic loss.  
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain  
materials or manufacture replacement parts.  
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company, including  
without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized to alter, modify,  
or enlarge this Warranty.  
Answers to any questions regarding warranty service and locations may be obtained by contacting:  
Woods Equipment  
Company  
2606 South Illinois Route 2  
Post Office Box 1000  
Oregon, Illinois 61061  
815-732-2141 tel  
815-732-7580 fax  
www.WoodsEquipment.com  
©2002 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods  
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are  
the property of their respective companies or mark holders. Specifications subject to change without notice.  
F-8494 (Rev. 6/23/2005)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Bolens Lawn Mower 149 813 000 User Manual
Craftsman Lawn Mower YT 4000 User Guide
Cub Cadet Lawn Mower 184 387 100 User Guide
Exmark Lawn Mower 4500 497 User Guide
Hubbell Lawn Mower SZ 18 User Guide
Land Pride Lawn Mower SF25 Series User Guide
Poulan Lawn Mower 186996 User Guide
Snapper Lawn Mower Lancer 4400 User Manual
Snapper Lawn Mower V2104 User Manual
Stiga Lawn Mower 13 6133 36 User Guide