Weed Eater Lawn Mower 186913 User Guide
MODEL NO. WET17H42STA  
17.0 HP 42 Inch  
Lawn Tractor  
For Parts and Service, contact our authorized distributor: call 1-800-849-1297  
For Technical Assistance: call 1-800-829-5886  
®
01029-weedeater  
186913 04.16.03 TR  
PRINTED IN U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY RULES  
Safe Operation Practices for Ride-On Mowers  
IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE  
TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.  
•
•
•
•
•
Be sure the area is clear of other people before mowing.Stop  
machine if anyone enters the area.  
Never carry passengers or children even with the blades  
off.  
Do not mow in reverse unless absolutely necessary. Always  
look down and behind before and while backing.  
Nevercarrychildren.Theymayfalloffandbeseriouslyinjured  
or interfere with safe machine operation.  
Keep children out of the mowing area and under the watchful  
care of another responsible adult.  
Be alert and turn machine off if children enter the area.  
Before and when backing, look behind and down for small  
children.  
WARNING: In order to prevent acci-  
dental starting when setting up, trans-  
porting, adjusting or making repairs,  
always disconnect spark plug wire  
and place wire where it cannot contact  
spark plug.  
WARNING: Do not coast down a hill  
in neutral, you may lose control of the  
tractor.  
•
•
•
•
•
Mow up and down slopes (15° Max), not across.  
Remove obstacles such as rocks, tree limbs, etc.  
Watchforholes,ruts,orbumps.Uneventerraincouldoverturn  
the machine. Tall grass can hide obstacles.  
Use slow speed. Choose a low gear so that you will not have  
to stop or shift while on the slope.  
Avoid starting or stopping on a slope. If tires lose traction,  
disengage the blades and proceed slowly straight down the  
slope.  
If machine stops while going uphill, disengage blades, shift  
into reverse and back down slowly.  
Donotturnonslopesunlessnecessary, andthen, turnslowly  
and gradually downhill, if possible.  
WARNING: Tow only the attachments  
that are recommended by and comply  
withspecificationsofthemanufacturer  
of your tractor. Use common sense  
when towing. Operate only at the low-  
est possible speed when on a slope.  
Too heavy of a load, while on a slope,  
is dangerous. Tires can lose traction  
with the ground and cause you to lose  
control of your tractor.  
•
•
•
•
WARNING  
Engine exhaust, some of its constituents, and cer-  
tain vehicle components contain or emit chemicals  
knowntotheStateofCaliforniatocausecancerand  
birth defects or other reproductive harm.  
WARNING  
Battery posts, terminals and related accessories  
containleadandleadcompounds,chemicalsknown  
to the State of California to cause cancer and birth  
defects or other reproductive harm. Wash hands  
after handling.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONGRATULATIONS on your purchase of a new tractor.  
Ithasbeendesigned,engineeredandmanufacturedtogive  
you the best possible dependability and performance.  
PRODUCT SPECIFICATIONS  
Gasoline Capacity  
and type:  
1.25 Gallons  
Unleaded Regular  
Shouldyouexperienceanyproblemyoucannoteasilyrem-  
edy,pleasecontactyournearestauthorizedservicecenter/  
department. We have competent, well-trained technicians  
and the proper tools to service or repair this tractor.  
Oil Type (API-SF-SJ):  
SAE 30 (above 32°F)  
SAE 5W-30 (below 32°F)  
Oil Capacity:  
W/Filter:  
62 oz  
55oz  
W/O Filter:  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your tractor properly.  
Always observe the “SAFETY RULES”.  
Spark Plug:  
(Gap: .030")  
Champion RN4C  
Ground Speed (MPH):  
Forward:  
Reverse:  
5.2  
2.7  
CUSTOMER RESPONSIBILITIES  
Tire Pressure:  
Front: 14 PSI  
•
•
Read and observe the safety rules.  
Follow a regular schedule in maintaining, caring for  
and using your tractor.  
Rear:  
12 PSI  
Charging System:  
Battery:  
3 Amps Battery  
5 Amps Headlights  
•
Follow the instructions under “Maintenace” and “Stor-  
age” sections of this owner’s manual.  
AMP/HR:  
MIN. CCA:  
CASE SIZE:  
28  
230  
U1R  
WARNING: This tractor is equipped with an internal com-  
bustion engine and should not be used on or near any  
unimprovedforest-covered,brush-coveredorgrass-covered  
land unless the engine’s exhaust system is equipped with  
a spark arrester meeting applicable local or state laws (if  
any). If a spark arrester is used, it should be maintained  
in effective working order by the operator.  
Blade Bolt Torque:  
27-35 FT. LBS.  
A spark arrester for the muffler is available through your  
nearestauthorizedservicecenter/department (SeeREPAIR  
PARTS section of this manual).  
TABLE OF CONTENTS  
SAFETY RULES .........................................................2-3  
PRODUCT SPECIFICATIONS....................................... 4  
CUSTOMER RESPONSIBILITIES................................. 4  
ASSEMBLY.................................................................6-8  
OPERATION .............................................................9-14  
MAINTENANCE SCHEDULE ...................................... 15  
MAINTENANCE..................................................... 15-18  
SERVICE AND ADJUSTMENTS ............................19-23  
STORAGE.................................................................... 24  
TROUBLESHOOTING ............................................25-26  
REPAIR PARTS - TRACTOR ..................................28-41  
WARRANTY................................................................. 44  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
UNASSEMBLED PARTS  
Steering Wheel  
Seat  
(1) Washer  
17/32 x 1-3/16 x 12 Gauge  
Steering  
Boot  
(1) Lock  
Washer 1/2  
Steering  
Extension  
Shaft  
Steering  
Wheel  
Insert  
(1) Bolt  
Steering  
Wheel  
Adapter  
Key  
(1) Large Flat  
Washer  
(1) Locknut 1/2-20  
(2) Keys  
(1) Oil Drain Tube  
Slope Sheet  
(1) Locknut 1/4-28  
(1) Hex Bolt 1/4-28 x 1-1/4  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.  
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use  
the correct tools as necessary to insure proper tightness.  
TOOLS REQUIRED FOR ASSEMBLY  
INSERT  
A socket wrench set will make assembly easier. Standard  
wrench sizes are listed.  
1/2 LOCK WASHER  
(1) 3/4" wrench  
Pliers  
LARGE FLAT  
WASHER  
(2) 7/16" wrenches  
Tire pressure gauge  
Utility knife  
Whenrightorlefthandismentionedinthismanual,itmeans  
when you are in the operating position (seated behind the  
steering wheel).  
STEERING  
WHEEL  
STEERING  
BOOT  
TO REMOVE TRACTOR FROM CAR-  
TON  
UNPACK CARTON  
TABS  
•
•
•
Remove all accessible loose parts and parts cartons  
from carton.  
Cut along dotted lines on all four panels of carton.  
Remove end panels and lay side panels flat.  
Check for any additional loose parts or cartons and  
remove.  
EXTENSION SHAFT  
1/4 HEX BOLT  
ADAPTER  
1/4 LOCKNUT  
BEFORE REMOVING TRACTOR FROM  
SKID  
ATTACH STEERING WHEEL (SEE FIG. 1)  
ASSEMBLE EXTENSION SHAFT AND BOOT  
LOWER  
STEERING  
SHAFT  
•
Slide extension shaft onto lower steering shaft. Align  
mountingholesinextensionandlowershaftsandinstall  
1/4 hex bolt and locknut. Tighten securely.  
TAB  
SLOTS  
FIG. 1  
IMPORTANT:TIGHTEN BOLT AND NUT SECURELY TO 10-12  
FT. LBS TORQUE.  
•
Place tabs of steering boot over tab slots in dash and  
push down to secure.  
HOW TO SET UPYOUR TRACTOR  
INSTALL STEERING WHEEL  
INSTALL SEAT (See Fig. 2)  
Adjust seat before tightening adjustment bolt.  
•
•
•
•
•
•
Position front wheels of the tractor so they are pointing  
straight forward.  
•
Remove adjustment bolt, lock washer and flat washer  
securing seat to cardboard packing and set aside for  
assembly of seat to tractor.  
Remove steering wheel adapter from steering wheel  
and slide adapter onto steering shaft extension.  
Position steering wheel so cross bars are horizontal  
(left to right) and slide inside boot and onto adapter.  
Assemble large flat washer, 1/2 hex nut and tighten  
securely.  
Snap steering wheel insert into center of steering  
wheel.  
•
•
•
•
Pivotseatupwardandremovefromthecardboardpack-  
ing. Remove the cardboard packing and discard.  
Place seat on seat pan so head of shoulder bolt is  
positioned over large slotted hole in pan.  
Push down on seat to engage shoulder bolt in slot and  
pull seat towards rear of tractor.  
Pivot seat and pan forward and assemble adjust-  
ment bolt, lockwasher and flat washer loosely. Do not  
tighten  
Remove protective materials from tractor hood and  
grill.  
IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES  
IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR  
IS TO ROLL OFF SKID.  
•
•
Lower seat into operating position and sit on seat.  
Slide seat until a comfortable position is reached  
which allows you to press clutch/brake pedal all the  
way down.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
•
•
Get off seat without moving its adjusted position.  
Raise seat and tighten adjustment bolt securely.  
Note: You may now roll or drive your tractor off the skid.  
Follow the appropriate instruction below to remove the  
tractor from the skid.  
TO ROLL TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
SEAT  
•
•
•
Press lift lever plunger and raise attachment lift lever  
to its highest position.  
Release parking brake by depressing clutch/brake  
pedal.  
Place freewheel control in "transmission disengaged  
position" (See “TO TRANSPORT” in the Operation  
section of this manual).  
SEAT PAN  
SHOULDER  
BOLT  
02466  
•
•
Roll tractor forward off skid.  
Removebandingholdingthedeflectorshieldupagainst  
tractor.  
TO DRIVE TRACTOR OFF SKID (See Op-  
eration section for location and function of  
controls)  
FLAT WASHER  
LOCK WASHER  
WARNING:Beforestarting,read,understandandfollow  
all instructions in the Operation section of this manual. Be  
sure tractor is in a well-ventilated area. Be sure the area in  
front of tractor is clear of other people and objects.  
02465  
•
Be sure all the above assembly steps have been com-  
pleted.  
ADJUSTMENT  
BOLT  
•
•
Check engine oil level and fill fuel tank with gasoline.  
FIG. 2  
Place freewheel control in "transmission engaged"  
position (see "TO TRANSPORT" in Operation section  
of this manual).  
Sit on seat in operating position, depress clutch/brake  
pedal and set the parking brake.  
Place motion control lever in neutral (N) position.  
Press lift lever plunger and raise attachment lift lever  
to its highest position.  
CHECK BATTERY (See Fig. 3)  
•
•
•
Lift seat pan to raised position.  
If this battery is put into service after month and year  
indicated on label (label located between terminals)  
charge battery for minimum of one hour at 6-10 amps.  
(See "BATTERY" in MAINTENANCE section of this  
manual for charging instructions).  
•
•
•
Starttheengine.Afterenginehasstarted,movethrottle  
control to idle position.  
•
•
Release parking brake.  
Slowlymovethemotioncontrolleverforwardandslowly  
drive tractor off skid.  
SEAT PAN  
•
•
Apply brake to stop tractor, setparkingbrakeandplace  
motion control lever in neutral position.  
Turn ignition key to "STOP" position.  
LABEL  
Continue with the instructions that follow.  
FIG. 3  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
✓CHECKLIST  
CHECK TIRE PRESSURE  
The tires on your tractor were overinflated at the factory  
for shipping purposes. Correct tire pressure is important  
for best cutting performance.  
BEFOREYOUOPERATEANDENJOYYOURNEW TRAC-  
TOR, WE WISH TO ASSURE THAT YOU RECEIVE THE  
BESTPERFORMANCEANDSATISFACTIONFROMTHIS  
QUALITY PRODUCT.  
•
Reduce tire pressure to PSI shown in “PRODUCT  
SPECIFICATIONS” section of this manual.  
PLEASE REVIEW THE FOLLOWING CHECKLIST:  
✓
✓
✓
All assembly instructions have been completed.  
No remaining loose parts in carton.  
Battery is properly prepared and charged. (Minimum  
1 hour at 6 amps).  
Seat is adjusted comfortably and tightened securely.  
All tires are properly inflated. (For shipping purposes,  
the tires were overinflated at the factory).  
Be sure mower deck is properly leveled side-to-side/  
front-to-rear for best cutting results. (Tires must be  
properly inflated for leveling).  
Check mower and drive belts. Be sure they are routed  
properly around pulleys and inside all belt keepers.  
Check wiring. See that all connections are still secure  
and wires are properly clamped.  
Before driving tractor, be sure freewheel control is in  
drive position.  
CHECK DECK LEVELNESS  
For best cutting results, mower housing should be properly  
leveled. See“TOLEVELMOWERHOUSING”intheService  
and Adjustments section of this manual.  
✓
✓
CHECK FOR PROPER POSITION OF ALL  
BELTS  
See the figures that are shown for replacing motion and  
mower blade drive belts in the Service and Adjustments  
section of this manual. Verify that the belts are routed  
correctly.  
✓
✓
✓
✓
CHECK BRAKE SYSTEM  
Afteryoulearnhowtooperateyourtractor,checktoseethat  
the brake is properly adjusted. See “TO ADJUST BRAKE”  
in the Service and Adjustments section of this manual.  
WHILE LEARNING HOW TO USEYOUR TRACTOR, PAY  
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT  
ITEMS:  
✓
Engine oil is at proper level.  
✓
Fuel tank is filled with fresh, clean, regular unleaded  
gasoline.  
✓
Become familiar with all controls - their location and  
function. Operate them before you start the engine.  
✓
✓
Be sure brake system is in safe operating condition.  
It is important to purge the transmission before oper-  
ating your tractor for the first time. Follow proper start-  
ing and transmission purging instructions (See “TO  
START ENGINE” and “PURGE TRANSMISSION” in  
the Operation section of this manual).  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean-  
IGNITION  
FAST  
SLOW  
REVERSE  
HIGH  
LOW  
NEUTRAL  
CHOKE  
P
LIGHTS ON  
ENGINE START  
ENGINE ON  
PARKING BRAKE  
PARKING BRAKE PARKING BRAKE  
ENGINE OFF  
LOCKED  
UNLOCKED  
OIL PRESSURE  
BATTERY  
REVERSE  
FUEL  
FORWARD  
OVER TEMP  
LIGHT  
MOWER HEIGHT  
MOWER LIFT  
15  
15  
15  
ATTACHMENT  
CLUTCH ENGAGED  
ATTACHMENT  
CLUTCH DISENGAGED  
SLOPE HAZARDS  
(SEE SAFETY RULES SECTION)  
DANGER, KEEP HANDS  
AND FEET AWAY  
KEEP AREA CLEAR  
DANGER indicates a hazard which, if not avoided,  
will result in death or serious injury.  
WARNING indicates a hazard which, if not avoided,  
could result in death or serious injury.  
FREE WHEEL  
(Automatic Models only)  
CAUTION indicates a hazard which, if not avoided,  
might result in minor or moderate injury.  
CAUTION when used without the alert symbol,  
indicates a situation that could result in damage  
to the tractor and/or engine.  
Failure to follow instructions  
could result in serious injury or  
death. The safety alert symbol  
is used to identify safety inform-  
ation about hazards which can  
result in death, serious injury  
and/or property damage.  
HOT SURFACES indicates a hazard which,  
if not avoided, could result in death, serious injury  
and/or property damage.  
FIRE indicates a hazard which, if not avoided,  
could result in death, serious injury and/or  
property damage.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOWYOUR TRACTOR  
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATINGYOUR TRACTOR  
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.  
Save this manual for future reference.  
ATTACHMENT  
CLUTCH LEVER  
LIGHT  
SWITCH  
POSITION  
IGNITION  
SWITCH  
LIFT LEVER  
PLUNGER  
THROTTLE/CHOKE  
CONTROL  
ATTACHMENT  
LIFT LEVER  
CLUTCH/BRAKE  
PEDAL  
PARKING  
BRAKE  
MOTION  
CONTROL  
LEVER  
FREE WHEEL  
CONTROL  
FIG. 4  
Our tractors conform to the safety standards of the American National Standards Institute.  
FREEWHEEL CONTROL: Disengages transmission for  
pushing or slowly towing the tractor with the engine off.  
MOTION CONTROL LEVER: Selects the speed and  
direction of tractor.  
ATTACHMENT LIFT LEVER: Used to raise and lower  
the mower deck or other attachments mounted to your  
tractor.  
ATTACHMENT CLUTCH LEVER: Used to engage the  
mower blades, or other attachments mounted to your  
tractor.  
LIGHT SWITCH POSITION: Turns the headlights on and  
off.  
THROTTLE/CHOKE CONTROL: Used for starting and  
controling engine speed.  
LIFT LEVER PLUNGER: Used to release attachment lift  
CLUTCH/BRAKE PEDAL: Used for declutching and brak-  
ing the tractor and starting the engine.  
PARKINGBRAKE:Locksclutch/brakepedalintothebrake  
position.  
lever when changing its position.  
IGNITION SWITCH: Used for starting and stopping the  
engine.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any tractor can result in foreign objects thrown into the eyes, which can result  
in severe eye damage. Always wear safety glasses or eye shields while operating your trac-  
tor or performing any adjustments or repairs. We recommend a wide vision safety mask over  
spectacles or standard safety glasses.  
•
Never use choke to stop engine.  
HOW TO USEYOUR TRACTOR  
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY  
POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY  
TO BE DISCHARGED, (DEAD).  
TO SET PARKING BRAKE (See Fig. 5)  
Your tractor is equipped with an operator presence sens-  
ing switch. When engine is running, any attempt by the  
operator to leave the seat without first setting the parking  
brake will shut off the engine.  
NOTE: Under certain conditions when tractor is standing  
idlewiththeenginerunning, hotengineexhaustgasesmay  
cause “browning” of grass. To eliminate this possibility, al-  
ways stop engine when stopping tractor on grass areas.  
•
Depress clutch/brake pedal into full “BRAKE” position  
and hold.  
CAUTION: Always stop tractor com-  
pletely,asdescribedabove,beforeleav-  
ing the operator's position; to empty  
grass catcher, etc.  
•
Place parking brake lever in“ENGAGED”position and  
releasepressurefromclutch/brakepedal. Pedalshould  
remain in “BRAKE” position. Make sure parking brake  
will hold tractor secure.  
ATTACHMENT CLUTCH  
TO USE THROTTLE CONTROL (See Fig. 5)  
Always operate engine at full throttle.  
LEVER "ENGAGED" POSI-  
TION  
THROTTLE/CHOKE  
CONTROL  
•
Operating engine at less than full throttle reduces the  
battery charging rate.  
IGNITION  
KEY  
•
Full throttle offers the best bagging and mower perfor-  
mance.  
"DISENGAGED"  
POSITION  
TO MOVE FORWARD AND BACKWARD  
(See Fig. 5)  
The direction and speed of movement is controlled by the  
motion control lever.  
PARKING BRAKE  
"ENGAGED"  
POSITION  
"BRAKE"  
POSITION  
•
Start tractor with motion control lever in neutral (N)  
position.  
•
•
Release parking brake.  
Slowly move motion control lever to desired position.  
MOTION  
CONTROL  
LEVER  
PARKING BRAKE  
"DISENGAGED" POSITION  
TO ADJUST MOWER CUTTING HEIGHT  
(See Fig. 5)  
CLUTCH/BRAKE PEDAL  
"DRIVE" POSITION  
FIG. 5  
The position of the attachment lift lever determines the  
cutting height.  
STOPPING (See Fig. 5)  
MOWER BLADES -  
•
•
Grasp lift lever.  
Press plunger with thumb and move lever to desired  
position.  
•
To stop mower blades,move attachment clutch lever  
to “DISENGAGED” position.  
The cutting height range is approximately 1-1/2 to 4".  
The heights are measured from the ground to the blade tip  
withtheenginenotrunning. Theseheightsareapproximate  
and may vary depending upon soil conditions, height of  
grass and types of grass being mowed.  
GROUND DRIVE -  
•
To stop ground drive, depress clutch/brake pedal into  
full “BRAKE” position.  
•
Move motion control lever to neutral (N) position.  
•
The average lawn should be cut to approximately 2-1/2  
inches during the cool season and to over 3 inches  
during hot months. For healthier and better looking  
lawns, mow often and after moderate growth.  
For best cutting performance, grass over 6 inches  
in height should be mowed twice. Make the first cut  
relatively high; the second to desired height.  
IMPORTANT:  
THE MOTION CONTROL LEVER DOES NOT  
RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/  
BRAKE PEDAL IS DEPRESSED.  
ENGINE -  
•
•
Move throttle control to slow position.  
NOTE: Failure to move throttle control to slow position and  
allowing engine to idle before stopping may cause engine  
to “backfi r e ” .  
•
Turn ignition key to “OFF” position and remove key.  
Always remove key when leaving tractor to prevent  
unauthorized use.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO OPERATE MOWER (See Fig. 6)  
TO TRANSPORT (See Figs. 4 and 7)  
Yourtractor isequippedwithanoperatorpresencesensing  
switch. Any attempt by the operator to leave the seat with  
the engine running and the attachment clutch engaged will  
shut off the engine.  
When pushing or towing your tractor, be sure to disengage  
transmission by placing freewheel control in freewheeling  
position. Free wheel control is located at the rear drawbar  
of tractor.  
•
•
Select desired height of cut.  
Start mower blades by engaging attachment clutch  
control.  
TO STOP MOWER BLADES - disengage attachment  
clutch control.  
•
•
•
•
Raiseattachmentlifttohighestpositionwithattachment  
lift control.  
Pull freewheel control out and down into the slot and  
release so it is held in the disengaged position.  
Do not push or tow tractor at more than two (2)  
MPH.  
To reengage transmission, reverse above procedure.  
•
CAUTION: Do not operate the mower  
without either the entire grass catcher,  
onmowerssoequipped,orthedeflector  
shield in place.  
NOTE: To protect hood from damage when transporting  
your tractor on a truck or a trailer, be sure hood is closed  
and secured to tractor. Use an appropriate means of tying  
hood to tractor (rope, cord, etc.).  
"ENGAGED" POSITION  
ATTACHMENT  
LIFT LEVER  
HIGH POSITION  
TRANSMISSION ENGAGED  
LOW  
POSITION  
ATTACHMENT  
CLUTCH LEVER  
"DISENGAGED"  
POSITION  
DEFLECTOR  
SHIELD  
TRANSMISSION DISENGAGED  
FIG. 6  
FIG. 7  
TO OPERATE ON HILLS  
TOWING CARTS AND OTHER ATTACHMENTS  
WARNING: Do not drive up or down  
hills with slopes greater than 15° and  
do not drive across any slope.  
Tow only the attachments that are recommended by and  
comply with specifications of the manufacturer of your trac-  
tor. Use common sense when towing.Too heavy of a load,  
while on a slope, is dangerous.Tires can lose traction with  
the ground and cause you to lose control of your tractor.  
•
Choose the slowest speed before starting up or down  
hills.  
•
•
Avoid stopping or changing speed on hills.  
If slowing is necessary, move throttle control lever to  
slower position.  
If stopping is absolutely necessary, push clutch/brake  
pedal quickly to brake position and engage parking  
brake.  
BEFORE STARTING THE ENGINE  
CHECK ENGINE OIL LEVEL  
•
The engine in your tractor has been shipped, from the  
factory, already filled with summer weight oil.  
•
•
•
Check engine oil with tractor on level ground.  
•
Move motion control lever to neutral (N) position.  
Remove oil fill cap/dipstick and wipe clean, reinsert the  
dipstick and screw cap tight, wait for a few seconds,  
remove and read oil level. If necessary, add oil until  
“FULL” mark on dipstick is reached. Do not overfill.  
IMPORTANT:  
THE MOTIONCONTROLLEVERDOESNOT  
RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/  
BRAKE PEDAL IS DEPRESSED.  
•
Torestartmovement, slowlyreleaseparkingbrakeand  
clutch/brake pedal.  
Slowly move motion control lever to slowest setting.  
Make all turns slowly.  
•
•
For cold weather operation you should change oil for  
easier starting (See “OIL VISCOSITY CHART” in the  
Maintenance section of this manual).  
To change engine oil, see the Maintenance section in  
this manual.  
•
•
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
COLD WEATHER STARTING ( 50° F and below)  
ADD GASOLINE  
•
When engine starts, allow engine to run with the  
throttle control in the choke position until the engine  
runs roughly, then move throttle control to fast posi-  
tion.This may require an engine warm-up period from  
several seconds to several minutes, depending on the  
temperature.  
•
Fill fuel tank to bottom of filler neck. Do not overfill.  
Use fresh, clean, regular unleaded gasoline with a  
minimum of 87 octane. (Use of leaded gasoline will  
increase carbon and lead oxide deposits and reduce  
valve life). Do not mix oil with gasoline. Purchase fuel  
in quantities that can be used within 30 days to assure  
fuel freshness.  
AUTOMATIC TRANSMISSION WARM UP  
•
Beforedrivingtheunitincoldweather,thetransmission  
should be warmed up as follows:  
CAUTION: Wipe off any spilled oil or  
fuel. Do not store, spill or use gasoline  
near an open flame.  
•
•
Be sure the tractor is on level ground.  
Place the motion control lever in neutral.  
Release the parking brake and let the clutch/  
brake slowly return to operating position.  
Allow one minute for transmission to warm up.This  
can be done during the engine warm up period.  
IMPORTANT: WHEN OPERATING IN TEMPERATURES  
BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE  
GASOLINE TO HELP INSURE GOOD COLD WEATHER  
STARTING.  
•
•
The attachments can also be used during the engine  
warm-upperiodafterthetransmissionhasbeenwarmed  
up.  
CAUTION: Alcohol blended fuels (called gasohol or  
usingethanolormethanol)canattractmoisturewhich  
leads to separation and formation of acids during  
storage. Acidic gas can damage the fuel system of  
anenginewhileinstorage.Toavoidengineproblems,  
the fuel system should be emptied before storage  
of 30 days or longer. Drain the gas tank, start the  
engineandletitrununtilthefuellinesandcarburetor  
are empty. Use fresh fuel next season. See Storage  
Instructions for additional information. Never use  
engine or carburetor cleaner products in the fuel  
tank or permanent damage may occur.  
NOTE: If at a high altitude (above 3000 feet) or in cold  
temperatures (below 32 F) the carburetor fuel mixture may  
need to be adjusted for best engine performance. See “TO  
ADJUST CARBURETOR” in the Service and Adjustments  
section of this manual.  
PURGE TRANSMISSION  
CAUTION: Never engage or disengage  
freewheel lever while the engine is run-  
ning.  
To ensure proper operation and performance, it is recom-  
mended that the transmission be purged before operating  
tractor for the first time. This procedure will remove any  
trapped air inside the transmission which may have de-  
veloped during shipping of your tractor.  
IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE  
REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD  
BE PURGED AFTER REINSTALLATION BEFORE OPERATING  
THE TRACTOR.  
TO START ENGINE (See Fig. 4)  
When starting the engine for the first time or if the engine  
has run out of fuel, it will take extra cranking time to move  
fuel from the tank to the engine.  
•
Besurefreewheelcontrolisinthetransmissionengaged  
position.  
•
Sit on seat in operating position, depress clutch/brake  
pedal and set parking brake.  
•
Place tractor safely on level surface with engine off and  
parking brake set.  
•
•
•
Place motion control lever in neutral (N) position.  
Move attachment clutch to “DISENGAGED” position.  
Move throttle control to choke position.  
•
Disengage transmission by placing freewheel control  
infreewheelingposition(See“TOTRANSPORT”inthis  
section of manual).  
NOTE: Before starting, read the warm and cold starting  
procedures below.  
•
•
Sitting in the tractor seat, start engine.After the engine  
is running, move throttle control to slow position. With  
motion control lever in neutral (N) position, slowly dis-  
engage clutch/brake pedal.  
Move motion control lever to full forward position and  
hold for five (5) seconds. Move lever to full reverse  
position and hold for five (5) seconds. Repeat this  
procedure three (3) times.  
•
Insertkeyintoignitionandturnkeyclockwiseto“START”  
position and release key as soon as engine starts.  
Do not run starter continuously for more than fifteen  
seconds per minute. If the engine does not start after  
several attempts, move throttle control to fast position,  
wait a few minutes and try again. If engine still does  
not start, move the throttle control back to the choke  
position and retry.  
NOTE: During this procedure there will be no movement  
of drive wheels. The air is being removed from hydraulic  
drive system.  
WARM WEATHER STARTING (50° F and above)  
•
When engine starts, move the throttle control to the  
fast position.  
•
The attachments and ground drive can now be used.If  
the engine does not accept the load, restart the engine  
and allow it to warm up for one minute using the choke  
as described above.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
•
•
Move motion control lever to neutral (N) position.Shut-  
off engine and set parking brake.  
Engage transmission by placing freewheel control in  
driving position (See“TOTRANSPORT”in this section  
of manual).  
•
•
Sitting in the tractor seat, start engine.After the engine  
is running, move throttle control to half (1/2) speed.  
With motion control lever in neutral (N) position, slowly  
disengage clutch/brake pedal.  
Slowly move motion control lever forward, after the  
tractor moves approximately five (5) feet, slowly move  
motion control lever to reverse position. After the trac-  
tor moves approximately five (5) feet return the mo-  
tion control lever to the neutral (N) position. Repeat  
this procedure with the motion control lever three (3)  
times.  
00272  
FIG. 8  
•
If grass is extremely tall, it should be mowed twice to  
reduce load and possible fire hazard from dried clip-  
pings. Make first cut relatively high; the second to the  
desired height.  
•
Your transmission is now purged and now ready for  
normal operation.  
•
•
Do not mow grass when it is wet. Wet grass will plug  
mower and leave undesirable clumps. Allow grass to  
dry before mowing.  
Always operate engine at full throttle when mow-  
ing to assure better mowing performance and proper  
discharge of material. Regulate ground speed by se-  
lecting a low enough gear to give the mower cutting  
performance as well as the quality of cut desired.  
MOWING TIPS  
•
Mower should be properly leveled for best mowing per-  
formance. See“TO LEVEL MOWER HOUSING”in the  
Service and Adjustments section of this manual.  
•
•
The left hand side of mower should be used for trim-  
ming.  
Drive so that clippings are discharged onto the area  
that has been cut. Have the cut area to the right of the  
machine. This will result in a more even distribution of  
clippings and more uniform cutting.  
•
When operating attachments, select a ground speed  
that will suit the terrain and give best performance of  
the attachment being used.  
•
Whenmowinglargeareas,startbyturningtotherightso  
that clippings will discharge away from shrubs, fences,  
driveways, etc. After one or two rounds, mow in the  
opposite direction making left hand turns until finished  
(See Fig. 8).  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
MAINTENANCE SCHEDULE  
USE  
HOURS  
HOURS  
FILL IN DATES  
HOURSHOURS  
50 100  
STORAGE  
EACH  
8
25  
SEASON  
AS YOU COMPLETE  
REGULAR SERVICE  
BEFORE  
SERVICE DATES  
EVERY EVERY EVERY EVERY EVERY  
BEFORE  
Check Brake Operation  
Check Tire Pressure  
Check Operator Presence and  
Interlock Systems  
T
Check for Loose Fasteners  
R
5
A
Sharpen/Replace Mower Blades  
3
C
Lubrication Chart  
T
Check Battery Level  
4
0
Clean Battery and Terminals  
R
Check Transaxle Cooling  
Check V-Belts  
Check Engine Oil Level  
Change Engine Oil (with oil filter)  
1,2  
Change Engine Oil (without oil filter)  
1,2  
E
Clean Air Filter  
N
2
2
G
Clean Air Screen  
I
Inspect Muffler/Spark Arrester  
N
Replace Oil Filter (If equipped)  
1,  
2
2
E
Clean Engine Cooling Fins  
Replace Spark Plug  
Replace Air Filter Paper Cartridge  
Replace Fuel Filter  
2
3 - Replace blades more often when mowing in sandy soil.  
4 - Not required if equipped with maintenance-free battery.  
5 - Tighten front axle pivot bolt to 35 ft.-lbs. maximum.  
Do not overtighten.  
1 - Change more often when operating under a heavy load or  
in high ambient temperatures.  
2 - Service more often when operating in dirty or dusty conditions.  
LUBRICATION CHART  
GENERAL RECOMMENDATIONS  
➀SPINDLE  
➀SPINDLE  
ZERK  
The warranty on this tractor does not cover items that have  
beensubjectedtooperatorabuseornegligence. Toreceive  
full value from the warranty, operator must maintain tractor  
as instructed in this manual.  
ZERK  
➀FRONT WHEEL  
BEARING ZERK  
➀FRONT WHEEL  
BEARING ZERK  
Some adjustments will need to be made periodically to  
properly maintain your tractor.  
➁ENGINE  
All adjustments in the Service and Adjustments section  
of this manual should be checked at least once each  
season.  
•
Once a year you should replace the spark plug, clean  
orreplaceairfilter, andcheckbladesandbeltsforwear.  
A new spark plug and clean air filter assure proper air-  
fuel mixture and help your engine run better and last  
longer.  
01964  
BEFORE EACH USE  
•
•
•
•
Check engine oil level.  
➀GENERAL PURPOSE GREASE  
➁REFER TO MAINTENANCE “ENGINE” SECTION  
Check brake operation.  
Check tire pressure.  
Check operator presence and  
interlock systems for proper operation.  
Check for loose fasteners.  
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS WHICH  
HAVE SPECIAL NYLON BEARINGS. VISCOUS LUBRICANTS WILL  
ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF  
THE SELF-LUBRICATING BEARINGS. IF YOU FEEL THEY MUST  
BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE  
LUBRICANT SPARINGLY.  
•
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
TRACTOR  
TRAILING  
EDGE UP  
MANDREL  
ASSEMBLY  
Always observe safety rules when performing any main-  
tenance.  
BLADE  
CENTER  
HOLE  
BRAKE OPERATION  
If tractor requires more than six (6) feet stopping distance  
at high speed in highest gear, then brake must be adjusted.  
(See“TOADJUSTBRAKE”intheServiceandAdjustments  
section of this manual).  
LOCK WASHER  
STAR  
FLAT WASHER  
TIRES  
BLADE BOLT (GRADE 8)*  
•
•
•
Maintainproperairpressureinalltires(See“PRODUCT  
SPECIFICATIONS” section of this manual).  
Keep tires free of gasoline, oil, or insect control chemi-  
cals which can harm rubber.  
Avoid stumps, stones, deep ruts, sharp objects and  
other hazards that may cause tire damage.  
*A GRADE 8 HEAT TREATED BOLT CAN BE  
IDENTIFIED BY SIX LINES ON THE BOLT HEAD.  
FIG. 9  
TO SHARPEN BLADE (See Fig. 10)  
NOTE: To seal tire punctures and prevent flat tires due to  
slow leaks, tire sealant may be purchased from your local  
parts dealer. Tire sealant also prevents tire dry rot and  
corrosion.  
NOTE: We do not recommend sharpening blade - but if  
you do, be sure the blade is balanced.  
Care should be taken to keep the blade balanced. An un-  
balancedbladewillcauseexcessivevibrationandeventual  
damage to mower and engine.  
OPERATOR PRESENCE SYSTEM  
Besureoperatorpresenceandinterlocksystemsarework-  
ing properly. If your tractor does not function as described,  
repair the problem immediately.  
•
The blade can be sharpened with a file or on a grind-  
ing wheel. Do not attempt to sharpen while on the  
mower.  
•
To check blade balance, you will need a 5/8" diameter  
steel bolt, pin, or a cone balancer. (When using a  
cone balancer, follow the instructions supplied with  
balancer).  
•
•
•
•
The engine should not start unless the brake pedal is  
fully depressed and attachement clutch control is in  
the disengaged position.  
Whentheengineisrunning,anyattemptbytheoperator  
to leave the seat without first setting the parking brake  
should shut off the engine.  
When the engine is running and the attachment clutch  
is engaged, any attempt by the operator to leave the  
seat should shut off the engine.  
The attachment clutch should never operate unless  
the operator is in the seat.  
NOTE: Do not use a nail for balancing blade. The lobes of  
the center hole may appear to be centered, but are not.  
•
Slidebladeontoanunthreadedportionofthesteelbolt  
or pin and hold the bolt or pin parallel with the ground.  
If blade is balanced, it should remain in a horizontal  
position. If either end of the blade moves downward,  
sharpen the heavy end until the blade is balanced.  
BLADE CARE  
CENTER HOLE  
Forbestresultsmowerbladesmustbekeptsharp. Replace  
bent or damaged blades.  
BLADE  
5/8" BOLT  
OR PIN  
BLADE REMOVAL (See Fig. 9)  
•
•
•
Raise mower to highest position to allow access to  
blades.  
Removebladebolt,lockwasherandflatwashersecuring  
blade.  
Install new or resharpened blade with trailing edge up  
towards deck as shown.  
FIG. 10  
IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER  
HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL  
ASSEMBLY.  
BATTERY  
Yourtractorhasabatterychargingsystemwhichissufficient  
for normal use. However, periodic charging of the battery  
with an automotive charger will extend its life.  
•
Reassemble blade bolt, lock washer and flat washer  
in exact order as shown.  
•
•
•
•
Keep battery and terminals clean.  
Keep battery bolts tight.  
Keep small vent holes open.  
Recharge at 6-10 amperes for 1 hour.  
•
Tighten blade bolt securely (27-35 Ft. Lbs. torque).  
IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
NOTE: The original equipment battery on your tractor is  
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)  
improve starting in cold weather, these multi-viscosity oils  
will result in increased oil consumption when used above  
32°F. Check your engine oil level more frequently to avoid  
possible engine damage from running low on oil.  
maintenance free. Do not attempt to open or remove caps  
or covers. Adding or checking level of electrolyte is not  
necessary.  
TO CLEAN BATTERY AND TERMINALS  
Corrosion and dirt on the battery and terminals can cause  
the battery to “leak” power.  
Change the oil after every 25 hours of operation or at least  
once a year if the tractor is not used for 25 hours in one  
year.  
•
Disconnect BLACK battery cable first then RED bat-  
tery cable and remove battery from tractor.  
Check the crankcase oil level before starting the engine  
and after each eight (8) hours of operation. Tighten oil fill  
cap/dipstick securely each time you check the oil level.  
•
•
Rinse the battery with plain water and dry.  
Cleanterminalsandbatterycableendswithwirebrush  
until bright.  
TO CHANGE ENGINE OIL (See Figs. 11 and 12)  
•
•
Coat terminals with grease or petroleum jelly.  
Determine temperature range expected before oil change.  
All oil must meet API service classification SF-SJ.  
Reinstall battery (See “REPLACING BATTERY" in  
the SERVICE AND ADJUSTMENTS section of this  
manual).  
•
•
•
•
Be sure tractor is on level surface.  
Oil will drain more freely when warm.  
Catch oil in a suitable container.  
Remove oil fill cap/dipstick. Be careful not to allow dirt  
to enter the engine when changing oil.  
V-BELTS  
Check V-belts for deterioration and wear after 100 hours  
of operation and replace if necessary. The belts are not  
adjustable. Replace belts if they begin to slip from wear.  
•
Remove yellow cap from end of drain valve and install  
the drain tube onto the fitting.  
TRANSAXLE COOLING  
The transmission fan and cooling fins should be kept clean  
to assure proper cooling.  
OIL DRAIN VALVE  
CLOSED AND  
LOCKED  
POSITION  
Do not attempt to clean fan or transmission while engine  
is running or while the transmission is hot.To prevent pos-  
sible damage to seals, do not use high pressure water or  
steam to clean transaxle.  
•
Inspect cooling fan to be sure fan blades are intact and  
clean.  
YELLOW CAP  
DRAIN  
TUBE  
•
Inspect cooling fins for dirt, grass clippings and other  
materials. To prevent damage to seals, do not use  
compressed air or high pressure sprayer to clean cool-  
ing fins.  
02463  
FIG. 12  
TRANSAXLE PUMP FLUID  
•
Unlock drain valve by pushing inward and turning  
counterclockwise.  
To open, pull out on the drain valve.  
After oil has drained completely, close and lock the  
drain valve by pushing inward and turning clockwise  
until the pin is in the locked position as shown.  
Remove the drain tube and replace the cap onto to the  
bottom fitting of the drain valve.  
Refill engine with oil through oil fill dipstick tube. Pour  
slowly. Do not overfill. For approximate capacity see  
“PRODUCT SPECIFICATIONS” section of this man-  
ual.  
The transaxle was sealed at the factory and fluid mainte-  
nance is not required for the life of the transaxle. Should  
the transaxle ever leak or require servicing, contact your  
nearest authorized service center/department.  
•
•
ENGINE  
LUBRICATION  
Only use high quality detergent oil rated with API service  
classification SF-SJ. Select the oil’s SAE viscosity grade  
according to your expected operating temperature.  
•
•
•
Use gauge on oil fill cap/dipstick for checking level.  
Be sure dipstick cap is tightened securely for accurate  
reading. Keep oil at “FULL” line on dipstick.  
SAE VISCOSITY GRADES  
SAE 30  
5W-30  
CLEAN AIR SCREEN  
-20  
0
30  
32 40  
0
100  
60  
80  
F
Air screen must be kept free of dirt and chaff to prevent  
engine damage from overheating. Clean with a wire brush  
or compressed air to remove dirt and stubborn dried gum  
fibers.  
C
-20  
10  
-30  
-10  
20  
30  
40  
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE  
oil_visc_chart1_e  
FIG. 11  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
ENGINE COOLING FINS  
IN-LINE FUEL FILTER (See Fig. 13)  
The fuel filter should be replaced once each season. If fuel  
filter becomes clogged, obstructing fuel flow to carburetor,  
replacement is required.  
Remove any dust, dirt or oil from engine cooling fins to  
preventenginedamagefromoverheating. Hoodandengine  
blower housing must be removed to clean engine cooling  
fins. See Engine Manual.  
•
•
•
•
With engine cool, remove filter and plug fuel line sec-  
tions.  
Place new fuel filter in position in fuel line with arrow  
pointing towards carburetor.  
Be sure there are no fuel line leaks and clamps are  
properly positioned.  
Immediately wipe up any spilled gasoline.  
AIR FILTER  
Your engine will not run properly using a dirty air filter.  
Remove cartridge every 25 hours of operation and tap to  
clean. Replace paper cartridge once a year or after every  
100 hours of operation, more often if used in very dusty,  
dirty conditions. See Engine Manual.  
CLAMP  
MUFFLER  
CLAMP  
Inspect and replace corroded muffler and spark arrester  
(if equipped) as it could create a fire hazard and/or dam-  
age.  
FUEL FILTER  
SPARK PLUGS  
FIG. 13  
Replace spark plugs at the beginning of each mowing  
season or after every 100 hours of operation, whichever  
occurs first. Spark plug type and gap setting are shown in  
“PRODUCT SPECIFICATIONS” section of this manual.  
CLEANING  
•
•
•
Clean engine, battery, seat, finish, etc. of all foreign  
matter.  
Keep finished surfaces and wheels free of all gasoline,  
oil, etc.  
Protect painted surfaces with automotive type wax.  
We do not recommend using a garden hose or pressure  
washer to clean your tractor unless the engine and trans-  
mission are covered to keep water out. Water in engine or  
transmission will shorten the useful life of your tractor. Use  
compressed air or a leaf blower to remove grass, leaves  
and trash from tractor and mower.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST-  
MENTS:  
•
•
•
•
•
•
Depress clutch/brake pedal fully and set parking brake.  
Place motion control lever in neutral (N) position.  
Place attachment clutch in “DISENGAGED” position.  
Turn ignition key to “STOP” and remove key.  
Make sure the blades and all moving parts have completely stopped.  
Disconnect spark plug wire from spark plug and place wire where it cannot come in contact  
with plug.  
TO INSTALL MOWER (See Fig. 14)  
TRACTOR  
TO REMOVE MOWER (See Fig. 14)  
Mower will be easier to remove from the right side of trac-  
tor.  
•
•
Raise attachment lift lever to its highest position.  
Slide mower under tractor with deflector shield to right  
side of tractor.  
•
•
Lower lift lever to its lowest position.  
Connect front links to mower deck and secure with  
retainer springs..  
•
•
Place attachment clutch in “DISENGAGED” position.  
Move attachment lift lever forward to lower mower to  
its lowest position.  
•
•
•
•
•
Connect suspension arms to rear deck brackets and  
secure with retainer springs.  
Connect anti-swaybar to chassis bracket and secure  
with retainer spring.  
Push clutch cable housing guide into bracket, slide col-  
lar onto guide and secure with large retainer spring.  
Place flat washer and clutch spring on idler pulley bolt  
and secure with small retainer spring.  
•
•
Roll belt off engine pulley.  
Removesmallretainerspring,andremoveclutchspring  
off pulley bolt.  
•
•
•
•
•
Remove large retainer spring, slide collar off and push  
housing guide out of bracket.  
Disconnect anti-swaybar from chassis bracket by re-  
moving retainer spring.  
Disconnect suspension arms from rear deck brackets  
by removing retainer springs.  
Disconnect front links from deck by removing retainer  
springs.  
Install belt onto engine pulley.  
TO LEVEL MOWER HOUSING  
Adjust the mower while tractor is parked on level ground  
or driveway. Make sure tires are properly inflated (See  
“PRODUCT SPECIFICATIONS”section of this manual). If  
tires are over or underinflated, you will not properly adjust  
your mower.  
Raise lift lever to raise suspension arms. Slide mower  
out from under tractor.  
IMPORTANT:IFANATTACHMENTOTHERTHANTHEMOWER  
DECK ISTO BE MOUNTED ONTHETRACTOR, REMOVETHE  
FRONTLINKSANDHOOKTHECLUTCHSPRINGINTOSQUARE  
HOLE IN FRAME.  
SMALL RETAINER SPRING  
CLUTCH SPRING  
FLAT WASHER  
SQUARE HOLE  
SMALL RETAINER SPRING  
SUSPENSION  
ENGINE PULLEY  
ARMS  
CLUTCH SPRING  
FRONT LINK  
RETAINER SPRING  
ANTI-SWAY BAR  
RETAINER SPRINGS  
(BOTH SIDES)  
COLLAR  
LARGE RETAINER  
SPRING  
HOUSING GUIDE  
BRACKET  
DEFLECTOR SHIELD  
FIG. 14  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
SIDE-TO-SIDE ADJUSTMENT (See Figs. 15 and 16)  
•
Whendistance“D”is1/8"to1/2"loweratfrontthanrear,  
tighten nut “F” against trunnion on both front links.  
•
Raise mower to its highest position.  
•
Recheck side-to-side adjustment.  
•
At the midpoint of both sides of mower, measure height  
from bottom edge of mower to ground. Distance “A”  
on both sides of mower should be the same or within  
1/4" of each other.  
MANDREL  
•
•
•
If adjustment is necessary, make adjustment on one  
side of mower only.  
To raise one side of mower, tighten lift link adjustment  
nut on that side.  
To lower one side of mower, loosen lift link adjustment  
nut on that side.  
"D"  
"D"  
FIG. 17  
BOTH FRONT LINKS MUST BE EQUAL IN LENGTH  
NOTE: Threefullturnsofadjustmentnutwillchangemower  
height about 1/8".  
•
Recheck measurements after adjusting.  
BOTTOM EDGE  
OF MOWER  
TO GROUND  
BOTTOM EDGE OF  
MOWER  
TO GROUND  
GROUND LINE  
NUT "F"  
TRUNNION  
NUT "E"  
“A”  
“A”  
FIG. 15  
SUSPENSION ARM  
FRONT LINKS  
FIG. 18  
LIFT LINK ADJUSTMENT NUT  
TO REPLACE MOWER BLADE DRIVE BELT  
(See Fig. 19)  
FIG. 16  
The mower blade drive belt may be replaced without tools.  
FRONT-TO-BACK ADJUSTMENT (See Figs. 17 and 18)  
Park the tractor on level surface. Engage parking brake.  
IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE  
FOLLOWINGFRONT-TO-BACKADJUSTMENTISNECESSARY,  
BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO  
MOWER WILL STAY LEVEL SIDE-TO-SIDE.  
BELT REMOVAL -  
•
Remove mower from tractor (See “TO REMOVE  
MOWER” in this section of this manual).  
To obtain the best cutting results, the mower housing  
should be adjusted so that the front is approximately 1/8"  
to 1/2" lower than the rear when the mower is in its high-  
est position.  
•
•
Work belt off both mandrel pulleys and idler pulleys.  
Pull belt away from mower.  
BELT INSTALLATION -  
•
•
Install new belt in reverse order of removal.  
Make sure belt is in all pulley grooves and inside all  
belt guides.  
Checkadjustmentonrightsideoftractor. Measuredistance  
“D” directly in front and behind the mandrel at bottom edge  
of mower housing as shown.  
•
Install mower in reverse order of removal instruc-  
tions.  
•
•
•
•
Before making any necessary adjustments, check that  
both front links are equal in length.  
If links are not equal in length, adjust one link to same  
length as other link.  
To lower front of mower loosen nut “E” on both front  
links an equal number of turns.  
When distance “D” is 1/8" to 1/2" lower at front than  
rear, tighten nuts “F” against trunnion on both front  
links.  
IDLER PULLEYS  
MANDREL PULLEY  
•
To raise front of mower, loosen nut “F” from trunnion  
on both front links. Tighten nut “E” on both front links  
an equal number of turns. The two front links must  
remain equal in length.  
MANDREL  
PULLEY  
FIG. 19  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
•
•
•
Remove belt from stationary idler and clutching idler.  
TO CHECK AND ADJUST BRAKE  
(See Fig. 20)  
Your tractor is equipped with an adjustable brake system  
which is mounted on the right side of the transaxle.  
Remove belt downward from around engine pulley.  
Pull belt slack toward rear of tractor. Carefully remove  
belt upwards from transmission input pulley and over  
cooling fan blades.  
•
Remove belt from center span keeper and pull belt  
away from tractor.  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be checked and adjusted.  
BELT INSTALLATION -  
•
Carefully work new belt down around transmission  
cooling fan and onto the input pulley.  
Slide belt into the center span keeper.  
Pull belt toward front of tractor and roll around the top  
groove of engine pulley.  
Install belt through stationary idler and clutching  
idler.  
Make sure belt is in all pulley grooves and inside all  
belt guides and keepers.  
Install mower (See “TO INSTALL MOWER” in this sec-  
tion of manual).  
TO CHECK BRAKE  
•
Park tractor on a level, dry concrete or paved surface,  
depress clutch/brake pedal all the way down and en-  
gage parking brake.  
•
•
•
Disengage transmission by placing freewheel control  
in “transmission disengaged” position. Pull freewheel  
control out and into the slot and release so it is held in  
the disengaged position.  
•
•
•
Therearwheelsmustlockandskidwhenyoutrytomanually  
push the tractor forward.If the rear wheels rotate, the brake  
needs to be adjusted or the pads need to be replaced.  
ENGINE  
PULLEY  
TO ADJUST BRAKE  
•
•
•
Depress clutch/brake pedal all the way down and en-  
CLUTCHING  
IDLER  
gage parking brake.  
Measure distance between brake operating arm and  
nut “A” on brake rod.  
If distance is other than 1-9/16", loosen jam nut and  
turn nut “A” until distance becomes 1-9/16". Retighten  
jam nut against nut “A”.  
STATIONARY  
IDLER  
•
•
Engage transmission by placing freewheel control in  
“transmission engaged” position.  
Roadtesttractorforproperstoppingdistanceasstated  
above. Readjust if necessary. If stopping distance is  
still greater than five (5) feet in highest gear, further  
maintenance is necessary. Replace brake pads or  
contact a qualified service center.  
TRANSMISSION  
INPUT PULLEY  
CENTER SPAN  
KEEPER  
FIG. 21  
NUT “A”  
1-9/16"  
OPERATING  
ARM  
TRANSAXLE MOTION CONTROL LEVER  
NEUTRAL ADJUSTMENT (See Fig. 22)  
The motion control lever has been preset at the factory and  
adjustment should not be necessary.  
JAM NUT  
•
•
•
•
•
•
Loosen adjustment bolt in front of the right rear wheel,  
and lightly tighten.  
Start engine and move motion control lever until tractor  
does not move forward or backward.  
Holdmotioncontrolleverinthatpositionandturnengine  
off.  
While holding motion control lever in place, loosen the  
adjustment bolt.  
Move motion control lever to the neutral (N) (lock gate)  
position.  
Tighten adjustment bolt securely.  
02557-LTH  
FIG. 20  
TO REPLACE MOTION DRIVE BELT  
(See Fig. 21)  
Park the tractor on level surface. Engage parking brake.  
For assistance, there is a belt installation guide decal on  
bottom side of left footrest.  
NOTE: Ifadditionalclearanceisneededtogettoadjustment  
bolt, move mower deck height to the lowest position.  
After above adjustment is made, if the tractor still creeps  
forward or backward while motion control lever is in neutral  
position, follow these steps:  
•
•
BELT REMOVAL -  
•
Remove mower (See “TO REMOVE MOWER” in this  
Loosen the adjustment bolt.  
Move the motion control lever 1/4 to 1/2 inch in the  
direction it is trying to creep.  
section of manual).  
NOTE: Observe entire motion drive belt and position of all  
belt guides and keepers.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
•
•
•
Tighten adjustment bolt securely.  
Start engine and test.  
If tractor still creeps, repeat above steps until satis-  
fi e d .  
TO START ENGINE WITH A WEAK BATTERY  
(See Fig. 24)  
WARNING: Lead-acid batteries gen-  
erate explosive gases. Keep sparks,  
flameandsmokingmaterialsawayfrom  
batteries. Always wear eye protection  
when around batteries.  
NEUTRAL  
LOCK GATE  
MOTION CONTROL  
LEVER  
If your battery is too weak to start the engine, it should be  
recharged. (See "BATTERY" in the MAINTENANCE sec-  
tion of this manual).  
ADJUSTMENT  
BOLT  
02239  
If “jumper cables” are used for emergency starting, follow  
this procedure:  
FIG. 22  
IMPORTANT: YOURTRACTOR IS EQUIPPEDWITH A 12VOLT  
SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT  
SYSTEM. DO NOT USEYOUR TRACTOR BATTERY TO START  
OTHER VEHICLES.  
TRANSMISSION REMOVAL/REPLACEMENT  
Should your transmission require removal for service or  
replacement, it should be purged after reinstallation and  
beforeoperatingthetractor. See“PURGETRANSMISSION”  
in the Operation section of this manual.  
TO ATTACH JUMPER CABLES -  
•
Connect one end of the RED cable to the POSITIVE  
(+) terminal of each battery(A-B), taking care not to  
short against tractor chassis.  
TO ADJUST STEERING WHEEL ALIGN-  
MENT  
If steering wheel crossbars are not horizontal (left to right)  
whenwheelsarepositionedstraightforward,removesteer-  
ing wheel and reassemble per instructions in the Assembly  
section of this manual.  
•
•
ConnectoneendoftheBLACKcabletotheNEGATIVE  
(-) terminal (C) of fully charged battery.  
Connect the other end of the BLACK cable (D) to good  
chassis ground, away from fuel tank and battery.  
TO REMOVE CABLES, REVERSE ORDER -  
•
BLACK cable first from chassis and then from the fully  
FRONT WHEEL TOE-IN/CAMBER  
charged battery.  
The front wheel toe-in and camber are not adjustable on  
your tractor. If damage has occurred to affect the front  
wheel toe-in or camber, contact your nearest authorized  
service center/department.  
•
RED cable last from both batteries.  
TO REMOVE WHEEL FOR REPAIRS  
(See Fig. 23)  
•
•
Block up axle securely.  
Removeaxlecover, retainingringandwasherstoallow  
wheel removal (rear wheel contains a square key - Do  
not lose).  
•
•
Repair tire and reassemble.  
On rear wheels only: align grooves in rear wheel hub  
and axle. Insert square key.  
Replace washers and snap retaining ring securely in  
axle groove.  
Replace axle cover.  
WEAK OR DEAD  
BATTERY  
FULLY CHARGED  
BATTERY  
•
•
FIG. 24  
NOTE: To seal tire punctures and prevent flat tires due to  
slow leaks, tire sealant may be purchased from your local  
parts dealer. Tire sealant also prevents tire dry rot and  
corrosion.  
REPLACING BATTERY (See Figs. 25 and 26)  
WARNING: Do not short battery ter-  
minals by allowing a wrench or any  
other object to contact both terminals  
at the same time. Before connect-  
ing battery, remove metal brace-  
lets, wristwatch bands, rings, etc.  
Positive terminal must be connected  
firsttopreventsparkingfromaccidental  
grounding.  
WASHERS  
RETAINING  
RING  
AXLE COVER  
•
•
Lift seat pan to raised position.  
DisconnectBLACKbatterycablefirstthenREDbattery  
cable and carefully remove battery from tractor.  
SQUARE KEY (REAR  
WHEEL ONLY)  
FIG. 23  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
•
•
Install new battery with terminals in same position as  
TO REMOVE HOOD AND GRILL ASSEMBLY  
(See Fig. 27)  
old battery.  
First connect RED battery cable to positive (+) terminal  
with hex bolt and keps nut as shown.Tighten securely.  
Slide terminal cover over terminal.  
Connect BLACK grounding cable to negative (-) ter-  
minal with remaining hex bolt and keps nut. Tighten  
securely.  
•
•
•
Raise hood.  
Unsnap headlight wire connector.  
Stand in front of tractor. Grasp hood at sides, tilt toward  
engine and lift off of tractor.  
•
•
To replace, reverse above procedure.  
SEAT PAN  
HOOD  
HEADLIGHT  
WIRE  
CONNECTOR  
FIG. 25  
01536  
KEPS  
NUT  
TERMINAL  
COVER  
HEX  
BOLT  
FIG. 27  
ENGINE  
TO ADJUST THROTTLE CONTROL CABLE  
POSITIVE (RED)  
CABLE  
NEGATIVE  
(BLACK) CABLE  
The throttle control has been preset at the factory and  
adjustment should not be necessary. Check adjustment  
as described below before loosening cable. If adjustment  
is necessary, see engine manual.  
FIG. 26  
TO REPLACE HEADLIGHT BULB  
TO ADJUST CARBURETOR  
•
•
Raise hood.  
Pull bulb holder out of the hole in the backside of the  
grill.  
Thecarburetorhasbeenpresetatthefactoryandadjustment  
shouldnotbenecessary.However,minoradjustmentmaybe  
requiredtocompensatefordifferencesinfuel,temperature,  
altitude or load. If the carburetor does need adjustment,  
see engine manual.  
•
•
Replace bulb in holder and push bulb holder securely  
back into the hole in the backside of the grill.  
Close hood.  
INTERLOCKS AND RELAYS  
Loose or damaged wiring may cause your tractor to run  
poorly, stop running, or prevent it from starting.  
•
Check wiring. See electrical wiring diagram in the  
Repair Parts section.  
TO REPLACE FUSE  
Replace with 20 amp automotive-type plug-in fuse. The  
fuse holder is located behind the dash.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
Immediately prepare your tractor for storage at the end  
of the season or if the tractor will not be used for 30 days  
or more.  
ENGINE  
FUEL SYSTEM  
IMPORTANT: ITISIMPORTANTTOPREVENTGUMDEPOSITS  
FROMFORMINGINESSENTIALFUELSYSTEMPARTSSUCH  
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK  
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT  
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING  
ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH  
LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING  
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM  
OF AN ENGINE WHILE IN STORAGE.  
WARNING: Never store the tractor with  
gasoline in the tank inside a building  
where fumes may reach an open flame  
orspark. Allowtheenginetocoolbefore  
storing in any enclosure.  
TRACTOR  
Removemowerfromtractorforwinterstorage. Whenmower  
istobestoredforaperiodoftime,cleanitthoroughly,remove  
all dirt, grease, leaves, etc. Store in a clean, dry area.  
•
•
Drain the fuel tank.  
Start the engine and let it run until the fuel lines and  
carburetor are empty.  
•
•
Never use engine or carburetor cleaner products in the  
fuel tank or permanent damage may occur.  
Use fresh fuel next season.  
•
Clean entire tractor (See “CLEANING” in the Mainte-  
nance section of this manual).  
Inspect and replace belts, if necessary (See belt re-  
placement instructions in the Service and Adjustments  
section of this manual).  
Lubricate as shown in the Maintenance section of this  
manual.  
Be sure that all nuts, bolts and screws are securely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
•
NOTE: Fuel stabilizer is an acceptable alternative in mini-  
mizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not drain  
the gas tank and carburetor if using fuel stabilizer.  
•
•
ENGINE OIL  
Drain oil (with engine warm) and replace with clean en-  
gine oil. (See “ENGINE” in the Maintenance section of  
this manual).  
•
Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
BATTERY  
•
•
Fully charge the battery for storage.  
After a period of time in storage, battery may require  
recharging.  
CYLINDER(S)  
•
•
Remove spark plug(s).  
Pour one ounce of oil through spark plug hole(s) into  
cylinder(s).  
•
To help prevent corrosion and power leakage during  
long periods of storage, battery cables should be dis-  
connected and battery cleaned thoroughly (see “TO  
CLEAN BATTERY AND TERMINALS” in the Mainte-  
nance section of this manual).  
After cleaning, leave cables disconnected and place  
cables where they cannot come in contact with battery  
terminals.  
•
•
Turn ignition key to “START”position for a few seconds  
to distribute oil.  
Replace with new spark plug(s).  
•
•
OTHER  
•
•
Do not store gasoline from one season to another.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
If battery is removed from tractor for storage, do not  
store battery directly on concrete or damp surfaces.  
•
•
If possible, store your tractor indoors and cover it to  
give protection from dust and dirt.  
Cover your tractor with a suitable protective cover that  
does not retain moisture. Do not use plastic. Plastic  
cannot breathe which allows condensation to form and  
will cause your tractor to rust.  
IMPORTANT: NEVERCOVERTRACTORWHILEENGINE AND  
EXHAUST AREAS ARE STILL WARM.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Will not start  
1. Out of fuel.  
1. Fill fuel tank.  
2. Engine not “CHOKED” properly.  
3. Engine flooded.  
4. Bad spark plug.  
5. Dirty air filter.  
2. See “TO START ENGINE” in Operation section.  
3. Wait several minutes before attempting to start.  
4. Replace spark plug.  
5. Clean/replace air filter.  
6. Dirty fuel filter.  
6. Replace fuel filter.  
7. Water in fuel.  
7. Drain fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
8. Loose or damaged wiring.  
8. Check all wiring.  
9. Carburetor out of adjustment.  
9. See “To Adjust Carburetor” in Service Adjustments  
section.  
10. Engine valves out of adjustment.  
10. Contact an authorized service center/department.  
Hard to start  
1. Dirty air filter.  
1. Clean/replace air filter.  
2. Bad spark plug.  
2. Replace spark plug.  
3. Weak or dead battery.  
4. Dirty fuel filter.  
3. Recharge or replace battery.  
4. Replace fuel filter.  
5. Stale or dirty fuel.  
6. Loose or damaged wiring.  
7. Carburetor out of adjustment.  
5. Drain fuel tank and refill with fresh gasoline.  
6. Check all wiring.  
7. See “To Adjust Carburetor” in Service Adjustments  
section.  
8. Engine valves out of adjustment.  
8. Contact an authorized service center/department.  
Engine will not turn over  
1. Brake pedal not depressed.  
2. Attachment clutch is engaged.  
3. Weak or dead battery.  
1. Depress brake pedal.  
2. Disengage attachment clutch.  
3. Recharge or replace battery.  
4. Replace fuse.  
4. Blown fuse.  
5. Corroded battery terminals.  
6. Loose or damaged wiring.  
7. Faulty ignition switch.  
8. Faulty solenoid or starter.  
9. Faulty operator presence switch(es).  
5. Clean battery terminals.  
6. Check all wiring.  
7. Check/replace ignition switch.  
8. Check/replace solenoid or starter.  
9. Contact an authorized service center/department.  
Engine clicks but will not  
start  
1. Weak or dead battery.  
1. Recharge or replace battery.  
2. Clean battery terminals.  
3. Check all wiring.  
2. Corroded battery terminals.  
3. Loose or damaged wiring.  
4. Faulty solenoid or starter.  
4. Check/replace solenoid or starter.  
Loss of power  
1. Cutting too much grass/too fast.  
2. Throttle in “CHOKE” position.  
3. Build-up of grass, leaves and trash under mower.  
4. Dirty air filter.  
1. Set in “Higher Cut” position/reduce speed.  
2. Adjust throttle control.  
3. Clean underside of mower housing.  
4. Clean/replace air filter.  
5. Low oil level/dirty oil.  
6. Faulty spark plug.  
7. Dirty fuel filter.  
5. Check oil level/change oil.  
6. Clean and regap or change spark plug.  
7. Replace fuel filter.  
8. Stale or dirty fuel.  
9. Water in fuel.  
8. Drain fuel tank and refill with fresh gasoline.  
9. Drain fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
10. Spark plug wire loose.  
11. Dirty engine air screen/fins.  
12. Dirty/clogged muffler.  
10. Connect and tighten spark plug wire.  
11. Clean engine air screen/fins.  
12. Clean/replace muffler.  
13. Loose or damaged wiring.  
14. Carburetor out of adjustment.  
13. Check all wiring.  
14. See “To Adjust Carburetor” in Service Adjustments  
section.  
15. Engine valves out of adjustment.  
15. Contact an authorized service center/department.  
Excessive vibration  
1. Worn, bent or loose blade.  
2. Bent blade mandrel.  
1. Replace blade. Tighten blade bolt.  
2. Replace blade mandrel.  
3. Loose/damaged part(s).  
3. Tighten loose part(s). Replace damaged parts.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
Engine continues to run  
when operator leaves  
seat with attachment  
clutch engaged  
1. Faulty operator-safety presence control system.  
1. Check wiring, switches and connections. If not  
corrected, contact an authorized service center/  
department.  
Poor cut - uneven  
1. Worn, bent or loose blade.  
2. Mower deck not level.  
1. Replace blade. Tighten blade bolt.  
2. Level mower deck.  
3. Buildup of grass, leaves, and trash under mower.  
4. Bent blade mandrel.  
3. Clean underside of mower housing.  
4. Replace blade mandrel.  
5. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
5. Clean around mandrels to open vent holes.  
Mower blades will not  
rotate  
1. Obstruction in clutch mechanism.  
2. Worn/damaged mower drive belt.  
3. Frozen idler pulley.  
1. Remove obstruction.  
2. Replace mower drive belt.  
3. Replace idler pulley.  
4. Frozen blade mandrel.  
4. Replace blade mandrel.  
Poor grass discharge  
1. Engine speed too slow.  
2. Travel speed too fast.  
1. Place throttle control in “FAST” position.  
2. Shift to slower speed.  
3. Wet grass.  
4. Mower deck not level.  
3. Allow grass to dry before mowing.  
4. Level mower deck.  
5. Low/uneven tire air pressure.  
6. Worn, bent or loose blade.  
7. Buildup of grass, leaves and trash under mower.  
8. Mower drive belt worn.  
5. Check tires for proper air pressure.  
6. Replace/sharpen blade. Tighten blade bolt.  
7. Clean underside of mower housing.  
8. Replace mower drive belt.  
9. Blades improperly installed.  
10. Improper blades used.  
11. Clogged mower deck vent holes from buildup of  
grass, leaves, and trash around mandrels.  
9. Reinstall blades sharp edge down.  
10. Replace with blades listed in this manual.  
11. Clean around mandrels to open vent holes.  
Headlight(s) not working  
(if so equipped)  
1. Switch is “OFF”.  
1. Turn switch “ON”.  
2. Bulb(s) or lamp(s) burned out.  
3. Faulty light switch.  
4. Loose or damaged wiring.  
5. Blown fuse.  
2. Replace bulb(s) or lamp(s).  
3. Check/replace light switch.  
4. Check wiring and connections.  
5. Replace fuse.  
Battery will not charge  
Loss of drive  
1. Bad battery cell(s).  
1. Replace battery.  
2. Poor cable connections.  
3. Faulty regulator (if so equipped).  
4. Faulty alternator.  
2. Check/clean all connections.  
3. Replace regulator.  
4. Replace alternator.  
1. Freewheel control in “disengaged” position.  
2. Motion drive belt worn, damaged, or broken.  
3. Air trapped in transmission during shipment  
or servicing.  
1. Place freewheel control in “engaged” position.  
2. Replace motion drive belt.  
3. Purge transmission.  
Engine “backfires”  
when turning engine  
“OFF”  
1. Engine throttle control not set at “SLOW”  
position for 30 seconds before stopping engine.  
1. Move throttle control to “SLOW” position and allow  
to idle for 30 seconds before stopping engine.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
SCHEMATIC  
RED  
BLACK  
BATTERY  
FUSE  
RED  
RED  
A
M
STARTER  
AMMETER  
(OPTIONAL)  
BLACK  
WHITE  
SOLENOID  
RED  
S
B
M
CLUTCH / BRAKE  
(PEDAL UP)  
G
A1  
A2  
WHITE  
L
SEAT SWITCH  
(NOT OCCUPIED)  
IGNITION  
SWITCH  
WHITE  
BLACK  
BLACK  
BLACK  
BLACK  
ATT'MENT CLUTCH  
(CLUTCH OFF)  
GROUNDING  
CONNECTOR  
BLACK  
HOUR  
METER  
(OPTIONAL)  
SPARK  
PLUG  
BLACK  
IGNITION  
UNIT  
GAP  
FUEL  
LINE  
(2 PLUGS ON  
TWIN CYL. ENGINES)  
BLUE  
CHARGING SYSTEM OUTPUT  
3 AMP DC @ 3600 RPM  
28 VOLTS AC MIN. @ 3600 RPM  
(CHARGING SYSTEM DISCONNECTED)  
RED  
FUEL SHUT-OFF SOLENOID  
(IF SO EQUIPPED)  
LIGHTING SYSTEM OUTPUT  
5 AMP AC @ 3600 RPM  
ALTERNATOR  
DIODE  
ORANGE  
14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF)  
NOTE  
YOUR TRACTOR IS  
BROWN  
BLACK  
EQUIPPED WITH A SPECIAL  
ALTERNATOR SYSTEM.  
THE LIGHTS ARE NOT  
CONNECTED TO THE  
BATTERY, BUT HAVE THEIR  
OWN ELECTRICAL SOURCE.  
BECAUSE OF THIS, THE  
HEADLIGHTS  
BRIGHTNESS OF THE LIGHTS  
WILL CHANGE WITH ENGINE  
SPEED. AT IDLE THE LIGHTS  
WILL DIM. AS THE ENGINE IS  
SPEEDED UP, THE LIGHTS  
WILL BECOME THEIR BRIGHTEST.  
NON-REMOVABLE  
CONNECTIONS  
IGNITION SWITCH  
REMOVABLE  
POSITION CIRCUIT “MAKE”  
CONNECTIONS  
OFF  
RUN/LIGHT  
M+G+A1  
B+A1  
NONE  
A2+L  
WIRING INSULATED CLIPS  
NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR  
SERVICING OF UNIT, THEY SHOULD BE REPLACED TO  
PROPERLY SECURE YOUR WIRING.  
RUN  
B+A1  
NONE  
START B + S + A1 NONE  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
ELECTRICAL  
22  
21  
42  
24  
41  
43  
27  
27  
40  
26  
27  
27  
25  
16  
16  
33  
30  
48  
52  
8
29  
27  
28  
2
1
90  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
ELECTRICAL  
KEY PART  
NO. NO.  
DESCRIPTION  
1
163465  
74760412  
176689  
176138  
175685  
4152J  
108432X  
146147  
175158  
73510400  
4207J  
121305X  
175566  
140401  
179720  
71110408  
131563  
178861  
140844  
141940  
180449  
Battery 12 Volt 28 Amp  
Bolt Hex Hd 1/4-20 Unc x 3/4  
Box Battery  
Switch Interlock Push -In  
Harness Asm Light W/4152J  
Bulb Light #1156  
Cable Battery 6 Ga 16”red  
Cable Battery 6 Ga Red 44" W/16W  
Fuse 20 AMP  
Nut Keps Hex 1/4-20 Unc  
Cable Ground 6 Ga 12” black  
Switch Plunger Nc Gray  
Switch Ign  
Key Ign  
Harness Ign  
Bolt Blk Fin Hex 1/4-20 x 1/2  
Cover Terminal Red  
Solenoid  
Adapter Ammeter  
Protection Wire Loop  
Cover Terminal  
2
8
16  
21  
22  
24  
25  
26  
27  
28  
29  
30  
33  
40  
41  
42  
43  
48  
52  
90  
NOTE: All component dimensions give in U.S. inches  
1 inch = 25.4 mm.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
CHASSIS AND ENCLOSURES  
212  
17  
30  
24  
29  
18  
12  
28  
24  
25  
26  
25  
26  
53  
31  
51  
52  
209  
55  
5
57  
5
209  
9
209  
208  
54  
11  
208  
207  
26  
64  
3
35  
1
13  
33  
3
10  
3
142  
3
145  
37  
37  
3
3
2
3
142 3  
208  
35  
14  
206  
3
14  
34  
26  
chassis-pl.lt_stlt_50  
38  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
CHASSIS AND ENCLOSURES  
KEY PART  
NO. NO.  
DESCRIPTION  
1
174619  
Chassis  
2
176554  
Drawbar  
3
17060612  
155272  
168336X010 Dash P/L  
Screw 3/8-16 x .75  
Bumper Hood/Dash  
5
9
10  
11  
12  
13  
14  
17  
18  
24  
25  
26  
28  
29  
30  
31  
33  
34  
35  
37  
38  
51  
52  
53  
54  
55  
57  
64  
72140608  
174996  
145660  
Bolt Carriage 3/8-16 x 1  
Panel Dash Lh  
Clip Tinnerman  
172105X010 Panel Dash Rh  
17490608  
Screw Thdrol 3/8-16 x 1-1/4  
159639X550 Hood LT/PL  
184921  
Bumper Hood  
74780616  
19131312  
73800600  
179844  
Bolt Fin Hex 3/8-16 x 1 Gr 5  
Washer 13/32 x 13/16 x 12 Ga  
Nut Lock Hex W/Ins 3/8-16 Unc  
Grille LT/PL  
170472X599 Lens LT/PL  
169468X550 Fender Footrest LT Pnt  
136619  
Bracket Support Fender  
179716X550 Footrest Pnt Lh  
179717X550 Footrest Pnt Rh  
72110606  
17490508  
175710  
73800400  
19091416  
144697  
161464  
144696  
74780412  
154798  
Bolt Rdhd Sht Sqnk 3/8-16 x 3/4  
Screw Thdrol 6/16-18 x 1/2 TYT  
Bracket Asm. Pivot Mower Rear  
Nut Lock Hex W/Ins 1/4-20  
Washer 9/32 x 7/8 x 16 Ga.  
Bracjet Grukke Lh  
Screw Hex Wshd 8-18 x 7/8  
Bracket Grille Rh  
Bolt Hex 1/4-20 x 3/4  
Dash Lower STLT  
142 175702  
145 156524  
206 170165  
207 17670508  
208 17670608  
209 17000612  
212 156229  
Plate Reinforcement STLT  
Rod Pivot Chassis/Hood  
Bolt Shoulder 5/16-18  
Screw Thdrol 5/16-18 x 1/2  
Screw Thdrol 3/8-16 x 1/2  
Screw Hex Wsh Thdr. 3/8-16 x 3/4  
Insert Lens Reflect P/L LT  
Plug Btn Blk .359  
- -  
5479J  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
DRIVE  
51  
57  
250  
89  
63  
212  
246  
70  
250  
116  
202  
245  
85  
66  
65  
69  
159  
59  
158  
162  
161  
251  
169  
197  
61  
198  
64  
56  
50  
150  
83  
41  
38  
14  
164  
85  
168  
81  
48  
163  
247  
21  
151  
51  
10  
82  
27  
49  
47  
166  
156  
62  
165  
8
35  
39  
32  
30  
120  
52  
36  
34  
37  
52  
16  
36  
35  
32  
95  
28  
53  
30  
252  
252  
29  
27  
22  
55  
24  
19  
25  
252  
77  
77  
15  
1
96  
drive-hydro.stlt_53  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
DRIVE  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
- - - - - -  
Transaxle (See Breakdown)  
Peerless LTH2000  
69  
70  
74  
75  
76  
77  
78  
81  
82  
83  
85  
89  
95  
96  
142432  
134683  
137057  
121749X  
Screw Hex Wsh Hi-Lo 1/4-1/2 Unc  
Keeper Belt Engine  
8
165619  
Rod Shift Fender Adjust  
Spacer  
10  
14  
15  
16  
19  
21  
22  
24  
25  
27  
28  
29  
30  
32  
34  
35  
36  
37  
38  
39  
41  
47  
48  
49  
50  
51  
52  
53  
55  
56  
57  
59  
61  
62  
63  
64  
65  
66  
STD561210 Pin Cotter 1/8 x 1 CAD  
Washer 25/32 x 1-1/4 x 16 Ga.  
10040400  
74490544  
Washer Lock Hvy Helical  
Bolt Hex FLGHD 5/16-18 Gr.5  
STD581075 E-Ring  
123583X  
121748X  
178140  
123782X  
19171216  
150360  
169373X428 Console, Shift  
178134  
4497H  
Key, Square  
STD541431 Nut Lock Hex W/Ins. 5/16-18 Unc  
STD541437 Nut Lock Hex W/Wsh 3/8-16 Unc  
106933X  
178141  
73350600  
106888X  
STD561210 Pin Cotter 1/8 x 3/4 CAD.  
Washer 25/32 x 1-5/8 x 16 Ga.  
Shaft Asm Cross Tapered  
Spring Torsion  
Knob 1/2-13  
Rod, Brake  
Nut, Hex Jam 3/8-16 Unc  
Spring, Brake Rod  
Washer 17/32 x 3/4 x 16 Ga.  
Nut Lock Center 1/4-28 FNTHD  
Disconnect Asm Rod Bypas LTH  
175765  
71673  
Rod, Parking Brake  
Cap, Parking Brake  
Bracket, Transaxle  
Bolt Hex Hd 5/16-18 Unc x 3/4  
Shaft, Foot Pedal  
Bearing, Nylon  
Retainer Spring 1" Zinc/Cad  
Bolt Rdhd Sqneck 3/8-16 x 1  
Nut Lock Flg 3/8-16  
116 72140608  
120 73900600  
150 175456  
151 19133210  
156 166002  
158 165589  
159 183900  
161 72140406  
162 73680400  
163 74780416  
164 19091010  
165 165623  
166 166880  
168 165492  
169 165580  
197 169613  
198 169593  
202 72110614  
212 145212  
245 178122  
246 178121  
247 181463  
250 17060612  
251 17060516  
252 19131616  
174973  
74760512  
175578  
120183X  
19211616  
1572H  
179114  
74760648  
175556  
127783  
154407  
123205X  
72110612  
Spacer Retainer  
Washer 13/32 x 2 x 10 Ga.  
Washer Srrted 5/16 ID x 1.125  
Bracket Shift Mount  
Washer  
Pin, Roll  
Hub Shift  
Pulley, Composite  
Bolt Fin Hex 3/8-16 x 3  
Keeper, Belt Idler  
Pulley, Idler, V-Groove  
Bellcrank, Clutch  
Retainer, Belt  
Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr 5  
Nut Crownlock 1/4-20 Unc  
Bolt Hex Fin 1/4-20 Unc x 1 Gr 5  
Washer 5/8 x .281 x 10 Ga  
Bracket Pivot Lever  
Screw 5/16-18 x 5/8  
Bolt Shoulder 5/16-18 x .561  
Plate Fastening  
Nyliner Snap-In 5/8’’ID  
Washer Nyl 7/8 ID x .105’’ Hyd  
Bolt Carr Sh 3/8-16 x 1-3/4 Gr.5  
Nut Hex Flange Lock  
Strap Torque Lh LTH2000  
Strap Torque Rh LTH2000  
Link Shift Transaxle LTH2000  
Screw . 3/8-16 x 3/4  
Screw 5/16-18 x 1  
Washer 13/32 x 1 x 16 Ga.  
Bolt Carr Sh 3/8-16 x 1-1/2 Gr 5  
STD541437 Nut Crownlock 3/8-16 Unc  
STD541431 Nut, Crownlock 5/16-18 Unc  
105710X  
105709X  
17060620  
178138  
169691  
17120614  
8883R  
175410  
173937  
STD551143 Washer  
154778  
Link, Clutch  
Spring, Return, Clutch  
Screw 3/8-16 x 1-1/4  
V-Belt  
Keeper, Center Span  
Screw 3/8-16 x .875  
Cover, Pedal  
Pulley, Engine  
Bolt Hex 7/16-20 x 4 Gr. 5  
Keeper Belt Engine Hydro  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
STEERING ASSEMBLY  
38  
12  
39  
1
41  
42  
37  
37  
36  
44  
51  
54  
88  
91  
43  
71  
68  
67  
67  
29  
46  
8
47  
67  
6
9
13  
17  
65  
46  
85  
2
8
6
7
9
85  
9
5
47  
7
9
3
32  
5
68  
82  
11  
29  
4
26  
43  
15  
40  
15  
29  
43  
6
28  
30  
8
15  
10  
steering_pl.lt_42  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
STEERING ASSEMBLY  
KEY PART  
NO. NO.  
DESCRIPTION  
1
140044X428 Wheel Steering Auto Black  
2
175131  
Axle Asm Front  
3
169840  
Spindle Asm Lh  
4
169839  
Spindle Asm Rh  
5
6266H  
Bearing Race Thrust Harden  
Washer 25/32 x 1 5/8 x 16ga  
Washer 27/32 x 1 1/4 x 16 Ga  
Ring Klip #t5304-75  
Bearing Col Strg Blk  
Link Drag Extended  
Lockwasher  
6
121748X  
19272016  
12000029  
3366R  
7
8
9
10  
11  
12  
13  
15  
17  
26  
28  
29  
30  
32  
36  
37  
38  
39  
40  
41  
42  
43  
44  
46  
47  
51  
54  
65  
67  
68  
71  
82  
85  
88  
91  
175121  
10040600  
73940800  
136518  
Nut Hex Jam Toplock 1/2-20 Unf  
Spacer Bearing Axle Front  
Hex Flange Lock  
145212  
180641  
Shaft Asm Strg  
126847X  
19131416  
17060612  
76020412  
130465  
Bushing Rod Tie Blk Lt  
Washer 13/32 x 7/8 x 16ga  
Screw 3/8-16 x 3/4  
Pin  
Rod Tie Wire Form 19 75 Mech  
Bushing Strg 5/8 Id Dash  
Screw TT #10-32 x 5 x 3/8 Flange  
155099  
152927  
140045X428 Insert Cap Strg  
19183812  
7810H  
100711L  
145054X428 Boot Dash Steering  
121749X  
180640  
Washer 9/16 ID x 2-3/8 OD 12 Gr  
Locknut Center  
Adaptor Wheel Strg 640/ 635id  
Washer 25/32 x 1 1/4 x 16 Ga  
Extension Steering  
121232X  
183226  
73540400  
71130420  
160367  
Cap Spindle Fr Top Blk  
Fitting Grease  
Nut Crownlock 1/4-28  
Bolt Hex 1/4-28 Unf x 1-1/4 Gr. 8  
Spacer Brace Axle  
72110618  
169827  
Bolt Rdhd Sq 3/8-16 Unc x 2-1/4  
Brace Axle  
175146  
Steering Asm  
169835  
Bracket Susp Chassis Front  
Fastener Christmas Tree  
Bolt Shoulder 7/16-20  
Clip Steering  
133835  
175118  
175553  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
ENGINE  
3
13  
2
1
4
62  
85  
78  
16  
38  
81  
14  
32  
78  
44  
46  
33  
45  
37  
31  
40  
23  
33  
29  
OPTIONAL EQUIPMENT  
Spark Arrester  
engine-tecumseh_2  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
2
3
170551  
17720408  
- - - - - -  
Control Throt /Ch Flag  
Screw Hex Thd Cut 1/4-20 x 1/2  
Engine Tec Model OHV170  
(Order Parts From Engine Manufac-  
turer)  
Muffler  
Gasket Muffler Tec  
Tube Drain Oil Easy  
Washer Lock Ext Tooth 3/8  
Shield Browning/Debris Guard  
Arrestor Spark  
Tank Fuel  
Cap Asm Fuel W/sym Vented  
Clamp Hose Blk  
37  
38  
40  
44  
45  
46  
62  
78  
81  
85  
137040  
Line Fuel 20”  
181654  
Plug Drain Oil Easy  
124028X  
17670412  
17000612  
19091416  
10040500  
17060620  
73510400  
71070512  
Bushing  
Screw Hexwsh Thdrol 1/4-20 x 3/4  
Screw Hex Wsh Thdrol 3/8-16  
Washer 9/32 x 7/8 x 16ga  
Washer Lock 5/16  
4
137351  
149272  
148456  
11050600  
169837  
137180  
184900  
140527  
123487X  
13  
14  
16  
23  
29  
31  
32  
33  
Screw 3/8-16 x 1-1/4  
Nut Keps Hex 1/4-20 Unc  
Screw Hex Hd Cap 5/16-18 x 3/4  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
SEAT ASSEMBLY  
1
8
9
8
9
14  
7
7
10  
5
6
22  
21  
2
24  
5
26  
16  
25  
15  
23  
4
13  
3
17  
12  
seat_lt.bolt_1  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
140116  
Seat  
14  
15  
16  
17  
21  
22  
23  
24  
25  
26  
72050412  
134300  
121250X  
123976X  
171852  
73800500  
71110814  
19171912  
127018X  
10040800  
Bolt Rdhd Sht Nk 1/4-20 x 1-1/2  
Spacer Split 28 x 96 Yel Zinc  
Spring Cprsn 1 27 Blk Pnt  
Nut Lock 1/4 Lge Flg Gr 5 Zinc  
Bolt Shoulder 5/16-18 Unc Blkz-2A  
Nut  
2
140551  
Bracket Pnt Pivot Seat (blk )  
3
71110616  
19131610  
145006  
73800600  
124181X  
17000616  
19131614  
182493  
Bolt  
4
Washer 13/32 x 1 x 10 Ga  
Clip Push-In Hinged  
Nut  
5
6
7
Spring Seat Cprsn 2 250 Blk Zi  
Screw 3/8-16 x 1.5  
Washer 13/32 x 1 x 14 Ga  
Pan Pnt Seat (blk )  
Bracket Pnt Mounting Switch  
Bushing Snap Blk Nyl 50 Id  
Bolt Hex Black  
8
Washer 17/32 x 1-3/16 x 12 Ga  
Bolt Shoulder 5/16-18 x 62  
Lockwasher  
9
10  
12  
13  
121246X  
121248X  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
DECALS  
3
16  
10  
11  
20  
9
4
4
1
6
5
2
14  
7
12  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
156811  
186906  
164579  
186763  
Decal Oper  
11  
12  
14  
16  
20  
- -  
162398  
181249  
160396  
164578  
145005  
138311  
178392  
186913  
Decal Ins Strg Whl  
2
Decal Tec 3 Yr Warranty  
Decal Hood LH  
Decal Footrest  
3
Decal V-Belt Schematic  
Decal Hood Rh  
Decal Bat Dan/Psn  
Decal Handle Lft Height Adjust  
Decal Chass. Disconnect  
Manual Owner's (English)  
4
Decal Side Pnl  
5
64-1734-29 Decal HP Engine  
6
179128  
162391  
171448  
157002  
Decal Deck "B" 42"  
Decal Deck  
7
- -  
9
Decal Fender Logo  
Decal Fender Danger  
- -  
10  
WHEELS & TIRES  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
1
1
59192  
Cap Valve Tire  
2
5,8  
2
65139  
Stem Valve  
3
106222X  
59904  
Tire F Ts 15 X 6 0 - 6 Service  
Tube Front (Service Item Only)  
4,10  
4
7
5
106732X624 Rim Asm 6"front Service  
278H  
9040H  
106108X624 Rim Asm 8"rear Service  
106268X  
7152J  
104757X428 Cap Axle 1 50 X 1 00  
144334  
6
Fitting Grease (Front Wheel Only)  
Bearing Flange (Front Wheel Only)  
3,9  
7
6
11  
8
9
Tire R Ts 18x9.5-8 Service  
Tube Rear (Service Item Only)  
10  
11  
- -  
Sealant, Tire ( 10 oz. Tube)  
NOTE: All component dimensions given in U.S. inches  
wheel_1  
1 inch = 25.4 mm  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
MOWER LIFT  
7
8
5
1
4
3
13  
2
4
6
6
11  
5
12  
13  
19  
20  
20  
13  
18  
17  
16  
15  
20  
31  
32  
19  
20  
15  
13  
31  
32  
lift-rh.1piece_3  
KEY  
NO.  
PART  
NO.  
KEY  
NO.  
PART  
NO.  
DESCRIPTION  
DESCRIPTION  
1
159460  
Wire Asm Inner/Sprg w/Plunger  
Shaft Asm Lift  
15  
16  
17  
18  
19  
20  
31  
32  
173288  
73350800  
175689  
Link Front  
Nut Jam Hex 1/2-13 Unc  
Trunnion Blk Zinc  
Nut Lock w/Wsh 1/2-13 Unc  
Arm Suspension Rear  
Retainer Spring  
2
159471  
3
105767X  
12000002  
19211621  
120183X  
109413X  
124526X  
139865  
Pin Groove  
4
E Ring #5133-62  
Washer 21/32 x 1 x 21 Ga.  
Bearing Nylon  
73800800  
139868  
5
6
163552  
7
Grip Handle  
169865  
Bearing Pvt Lift  
Nut Crownlock 3/8-24  
8
Button Plunger  
73540600  
11  
12  
13  
Link Lift Lh  
139866  
4939M  
Link Lift Rh  
NOTE: All component dimensions given in U.S. inches  
Retainer Spring  
1 inch = 25.4 mm  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
MOWER DECK  
68  
67  
40  
37  
157  
158  
36  
40  
143  
156  
153  
155  
151  
152  
45  
150  
144  
159  
46  
40  
37  
153  
154  
145  
184  
59  
148  
44  
56  
55  
53  
52  
146  
33  
32  
31  
48  
54  
142  
147  
30  
34  
1
21  
21  
2
21  
147  
21  
142  
23  
24  
25  
26  
2
16  
28  
15  
14  
27  
20  
18  
29  
3
18  
149  
4
13  
5
6
11  
10  
9
19  
21  
42_deck_man-t-path_3  
8
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
TRACTOR - - MODEL NUMBER WET17H42STA  
MOWER DECK  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
165892  
Mower Deck Assembly, 42"  
Bolt  
44  
45  
46  
48  
52  
53  
54  
55  
56  
59  
67  
68  
140088  
4497H  
Guard, Mandrel, LH  
2
72140506  
138017  
165460  
4939M  
Retainer  
3
Bracket Asm Fr. Sway Bar 3/42  
Bracket Asm Deck 42" Sway Bar  
Retainer Spring  
137729  
133944  
139888  
184907  
178515  
155046  
165723  
141043  
106932X  
144959  
Screw, Thdrol 1/4-20 x 5/8 T  
Washer, Hardened  
4
5
Bolt, Shoulder 5/16-18 Unc  
Arm Assembly, Pad, Brake  
Washer, Hardened  
6
178024  
850857  
10030600  
140296  
Bar Sway Deck  
8
Bolt 3/8-24 x 25 Grade 8 patched  
Washer, Lock  
9
Arm, Idler  
10  
Washer, Hardened  
Spacer, Retainer  
(The following blades are available)  
Blade, 42" Mulching Std (For mulch-  
ing mowers only)  
Guard TUV Idler  
11  
- -  
- -  
134149  
139775  
138971  
Knob  
V-Belt, 42" Mower  
Blade, 42" Mulching Premium (For  
better wear when mulching  
Blade, 42" Hi-Lift (For bagging or  
discharging)  
Shaft Assembly, Mandrel, Vented  
Housing, Mandrel, Vented  
Bearing, Ball, Mandrel  
Stripper, Mandrel Deck  
Bolt, Carriage 5/16-18 x 5/8  
Bolt, Shoulder  
Baffle, Vortex  
Nut  
Bracket, Deflector Mower 42"  
Cap, Sleeve 80 x 112 Blk Mower  
Spring, Torsion, Deflector 2 52  
Nut, Push Phos & Oil  
142 165890  
143 157109  
144 158634  
145 165888  
146 171977  
147 131335  
148 169022  
149 165898  
150 19091216  
151 169670  
152 169676  
153 169674  
154 169675  
155 169671  
156 169672  
157 169669  
158 17720408  
159 72140614  
184 19131410  
Arm Spring Brake Mower  
Bracket Arm Idler 42"  
Keeper Belt 42" Clutch Cable  
Pulley Idler Flat  
13  
14  
15  
16  
18  
19  
20  
21  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
36  
37  
40  
137645  
128774  
110485X  
174493  
72140505  
132827  
159770  
73680500  
177563  
105304X  
123713X  
110452X  
Bolt Carriage Idler  
Spring Extension  
Spring Return Idler  
Retainer Spring Yellow  
Washer 9/32 x 3/4 x 16 Ga.  
Bracket Clutch Cable  
Clutch Cable 42"  
Washer Flat 3/8" Type B  
Spring Retainer  
Spring Retention LVR CLTCH CAB  
Spacer Clutch Cable  
Rod Clutch Cable 3/8"  
Screw Hex Thd Cut 1/4-20 x 1/2  
Bolt Rdhd Sqn 3/8-16 Unc x 1-3/4  
Washer 13/32 x 7/8 x 10 Ga.  
Mandrel Assembly (Includes Hous-  
ing, Shaft and Shaft Hardware  
Only-Pulley Not Included)  
Replacement Mower, Complete  
130968X428 Shield, Deflector 42" Blk  
19111016  
131491  
Washer 11/32 x 5/8 x 16 Gauge  
Rod, Hinge 42" 6 75 W/G  
Screw Thdrol Washer Head  
Washer, Spacer Mower Vented  
Pulley, Mandrel  
173984  
- -  
130794  
129963  
153535  
178342  
Nut, Toplock 9/16 Flange  
Bolt  
Pulley, Idler, Flat  
Washer 13/32 x 13/16 x 16 Gauge  
Nut  
- -  
171639  
72110614  
131494  
19131316  
73680600  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE  
POLICY  
®
®
WARRANTY  
Issued January 1980  
Revised January 1991  
LIMITED WARRANTIES  
FOR  
NEW PEERLESS GEAR POWER TRAIN COMPONENTS  
A. Products Warranted  
Peerless Gear and Machine Division ofTecumseh Products Company (“Tecumseh”), subject to the limitations contained below,  
will, at its option, repair or replace, without charge for parts or labor only, any part of a new Power Train Component (which as used  
herein means and includes the transaxle, gear box, transmission, differential and right angle drives, and any part of the Power Train  
Component), EXCEPT any new Power Train Component incorporated in equipment used for commercial or rental purposes, which is  
found upon examination by any Tecumseh Authorized Service Outlet or by Tecumseh’s factory in Grafton, Wisconsin, to be DEFECTIVE  
IN MATERIAL AND/OR WORKMANSHIP if received by Tecumseh or a Tecumseh Authorized Service Outlet for such examination within  
TWO YEARS from the date of sale to the original consumer purchaser of Peerless Series 820, 900, 910, 915, 920, 930 transaxles and  
Series 1100 angle drive and ONEYEAR for all other Peerless products. New PowerTrain Components incorporated in equipment used for  
commercial purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted  
for NINETY (90) DAYS ONLY, and must be received by Tecumseh or by a Tecumseh Authorized Service Outlet for such examination  
within 90 days from the date of sale to the original purchaser. New Power Train Components Incorporated in equipment used for rental  
purposes are warranted in the same manner and to the same extent EXCEPT such Power Train Components are warranted for THIRTY  
(30) DAYS ONLY, and must be received by Tecumseh or a Tecumseh Authorized Service Outlet within 30 days from the date of sale to  
the original purchaser.  
B. Products And Items Not Warranted  
1.  
2.  
Alterations or Modifications of Power Train Components.  
Accidents, Normal Maintenance, Failure to follow the Original Equipment Manufacturer’s Manual.  
This warranty covers only parts of new Power Train Components which are found upon examination to be defective in material  
or workmanship as delivered to the original purchaser. This warranty does not cover defects caused by depreciation or damage caused  
by normal wear, accidents, improper maintenance, improper use or abuse of the product, failure to follow the instructions contained in  
an Instruction Manual for the operation of the Power Train Component and parts. The cost of normal maintenance and replacement of  
service items which are not defective shall be paid for by the original purchaser.  
C. Securing Warranty Service  
Warranty service can be arranged for by contacting either a Tecumseh Authorized Service Outlet (any Tecumseh Registered  
Service Dealer, Tecumseh Authorized Service Distributor, or Tecumseh Central Warehouse Distributor) or by contacting Tecumseh, c/o  
Service Manager, Engine and Transmission Group Service Division, 900 North Street, Grafton, Wisconsin 53024. Warranty service  
can only be performed by a Tecumseh Authorized Service Outlet or by Tecumseh at its factory in Grafton, Wisconsin. At the time of  
requesting warranty service, evidence must be presented of the date of sale to the original purchaser. The purchaser shall pay any  
charges for making service calls and/or for transporting the product to and from the place where the inspection and/or warranty work  
is performed. The purchaser shall be responsible for any damage or loss incurred in connection with the transportation of Power Train  
Components and/or part(s) of the Power Train Components submitted for inspection and/or warranty work.  
D. Limitation of Damages and Implied Warranties  
The foregoing EXPRESSED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. Neither Tecumseh nor any  
of its affiliates makes any warranties, representations or promises, written or oral, as to the quality of the Power Train Component or any  
of its parts, other than as set forth herein.  
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, TO THE EXTENT THAT  
EITHER MAY APPLY TO ANY PART(S) OF POWER TRAIN COMPONENTS, SHALL BE LIMITED IN DURATION TO THE PERIODS  
OF THE EXPRESSED WARRANTIES DEFINED IN PARAGRAPH A HEREOF. IN NO EVENT WILL TECUMSEH BE LIABLE FOR ANY  
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES AND/OR EXPENSES. Some states do not allow limitations on how long  
an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation(s) or exclusion(s)  
may not apply to you. This warranty gives you specific legal rights and you may also have other legal rights which vary from state to  
state.  
E. No Dealer Warranty  
Tecumseh neither assumes nor authorizes any other person, natural or corporate, to assume forTecumseh any other obligations  
or liabilities in connection with or with respect to any part(s) of a Power Train Component. The seller or dealer of part(s) of a Power Train  
Component has no authority, whatsoever, to make any representations or promises on behalf of Tecumseh or to modify the terms or  
limitations of Tecumseh’s warranty in any way.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION  
ONLY RIDE UP AND DOWN HILL,  
NOT ACROSS HILL  
15 DEGREES MAX.  
WARNING: To avoid serious injury, operate your tractor up and  
down the face of slopes, never across the face. Do not mow  
slopes greater than 15 degrees. Make turns gradually to prevent  
tipping or loss of control. Exercise extreme caution when  
changing direction on slopes.  
1. Fold this page along dotted line indicated above.  
2. Hold page before you so that its left edge is vertically parallel to a tree  
trunk or other upright structure.  
3. Sight across the fold in the direction of hill slope you want to measure.  
4. Compare the angle of the fold with the slope of the hill.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materi-  
als and workmanship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or  
replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we find to be defective due  
to materials or workmanship. This Warranty is subject to the following limitations and exclusions.  
1. This warranty does not apply to the engine, other than EHP manufactured transaxle/transmission components,  
battery (except as noted below) or components parts thereof. Please refer to the applicable manufacturer's  
warranty on these items.  
2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of  
the purchaser. Transportation charges for any parts submitted for replacement under this warranty must be  
paid by the purchaser unless such return is requested by Electrolux Home Products.  
3. Battery Warranty: On products equipped with a Battery, we will replace, without charge to you, any battery  
which we find to be defective in manufacture, during the first ninety (90) days of ownership. After ninety (90)  
days, we will exchange the Battery, charging you 1/12 of the price of a new Battery for each full month from  
the date of the original sale. Battery must be maintained in accordance with the instructions furnished.  
4. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the  
date of original purchase.  
5. This Warranty applies only to products which have been properly assembled, adjusted, operated, and main-  
tained in accordance with the instructions furnished. This Warranty does not apply to any product which has  
been subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal  
wear of the product.  
6. Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments,  
standard hardware and normal maintenance.  
7. In the event you have a claim under this Warranty, you must return the product to an authorized service deal-  
er.  
Should you have any unanswered questions concerning this Warranty, please contact:  
In Canada contact:  
Electrolux Home Products, Inc.  
Outdoor Products Customer Service Dept.  
250 Bobby Jones Expressway  
Augusta, GA 30909 USA  
Electrolux Canada Corp.  
7075 Ordan Drive  
Mississauga, Ontario  
L5T 1K6  
giving the model number, serial number and date of purchase of your product and the name and address of the authorized  
dealer from whom it was purchased.  
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRAN-  
TIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas  
do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above limi-  
tations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights which  
vary from locale to locale.  
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Agri Fab Lawn Mower 45 0369 page
Braun Lawn Mower 5316 User Manual
Craftsman Lawn Mower 91725354 User Guide
Craftsman Lawn Mower YT 4500 User Guide
Husqvarna Lawn Mower YTH2648 TF User Guide
Land Pride Lawn Mower RCF45180 User Guide
Scag Power Equipment Lawn Mower GC STC CSV User Guide
Snapper Lawn Aerator 4559 User Manual
Snapper Lawn Mower MCR5215014KWV User Manual
White Outdoor Lawn Mower Z 165 User Guide