M26 SERIES
Mechanical Windrow Sweeper
For Simplicity Legacy
SWEEPSTER, Inc.
2800 N. Zeeb Road • Dexter, MI 48130
(734) 996-9116 • FAX (734) 996-9014
1-800-456-7100
51-3845, 7/04
3
Table of Contents
Section 1 ... Operation and Maintenance
Section 2 ... Service
Section 3 ... Parts
Section 4 ... Appendix
51-3845, 7/04
4
51-3845, 7/04
5
Operation and
Maintenance
M26 Series
Table of Contents
Introduction .............................................................. 7
Safety .................................................................... 6-12
General Safety Information ..................................... 8-9
Safety Signs and Labels .................................... 10-12
Operation ............................................................ 13-20
Installation ......................................................... 13-15
Operating Tips ................................................... 16-19
Removing Sweeper and Hitch................................. 20
Maintenance ....................................................... 21-25
Daily Maintenance ............................................. 21-22
Brush Replacement ........................................... 22-24
Adjusting Drive Chain Idler ...................................... 25
Adjusting Brush Pattern........................................... 25
51-3845, 7/04
6
Introduction
SAFETY SECTION
INTRODUCTION
Serial & Part Numbers
On your unit you will find a serial number plate and/or part number plate(s). The numbers on these plates are very
important if you wish to order parts or accessories. For your convenience, record numbers in the appropriate space
below.
51-3845, 7/04
7
Introduction
SAFETY SECTION
INTRODUCTION
SWEEPSTER, Inc.
2800 North Zeeb Road
Dexter, Michigan 48130
Importance of this Manual
This operator’s manual should be regarded as part of
the sweeper. Suppliers of both new and secondhand
sweepers are advised to keep documentation indicat-
ing that this manual was provided with the sweeper.
Phone: (734) 996-9116 • (800) 456-7100
FAX: (734) 996-9014
e-mail: sweep@sweepster.com
For help with installation, operation or maintenance
procedures, contact ourTechnical Service Department.
Direct product questions and parts orders to our Sales
Department.
The manual contains information regarding installation,
operation and maintenance required for this sweeper
model and optional equipment. It also includes
detailed parts lists.
__________________________________________
When ordering parts or accessories, be prepared to
give the following information:
Purpose of Sweeper
• Sweeper model, serial number and date of
purchase
• Prime mover make and model
This sweeper is designed solely for use in construction
cleanup, road maintenance, grounds maintenance,
snow removal and similar operations. Use in any other
way is considered contrary to the intended use.
Compliance with and strict adherence to operation,
service and repair conditions, as specified by the
manufacturer, are also essential elements of the
intended use.
• Part number, description and quantity
__________________________________________
Terms Used in Manual
Right-hand, left-hand, front and rear are determined
from the operator’s perspective (either the operator’s
seat or standing behind a walk-behind unit), facing
forward in the normal operating position.
This sweeper should be operated, serviced and
repaired only by persons who are familiar with its
characteristics and acquainted with relevant safety
procedures.
Prime mover refers to the tractor, truck, loader or tow
vehicle that a sweeper is mounted on or towed by.
__________________________________________
Accident prevention regulations, all other generally
recognized safety regulations and all road traffic
regulations must be observed at all times.
Optional Equipment
Any modifications made to this sweeper may relieve
the manufacturer of liability for any resulting damage
or injury.
Installation instructions for optional equipment, if
applicable, appear with parts lists in the back of the
manual.
__________________________________________
__________________________________________
Safety Alert Symbol
Specifications & Features
This safety alert symbol indicates important
safety messages in this manual. When you see
this symbol, be alert to the possibility of injury.
Carefully read the message that follows and inform
other operators.
Due to continuous product improvement, specifica-
tions and features may change without notice.
__________________________________________
Warranty
__________________________________________
To validate the warranty for this unit, fill out the war-
ranty card or warranty pages located at the back of
this manual. Then, send this information to
SWEEPSTER.
Contacting SWEEPSTER
If you have any questions about information in this
manual or need to order parts, please call, write, FAX
or e-mail SWEEPSTER.
__________________________________________
51-3845, 7/04
8
Safety Information
SAFETYSECTION
GENERAL INFORMATION
• Check prime mover tire pressure before
sweeping.
Read this Manual
Read all safety information in this manual. All operators
must read and understand the entire contents of this
manual before sweeping. General safety practices are
listed on Safety Information pages and specific safety
information is located throughout this manual.
• Check tire ratings to be sure they match the
prime mover load. Weigh the sweeper end of the
prime mover, if necessary, to insure proper tire
rating.
__________________________________________
• Remove from the sweeping area all property that
could be damaged by debris flying from the
sweeper.
Hazard Definitions
Four hazard classifications are used in this manual.
They are
• Be sure all persons not operating the sweeper
are clear of the sweeper discharge area.
CAUTION – Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury.
• Always wear proper apparel such as a long-
sleeve shirt buttoned at the cuffs; safety glasses,
goggles or a face shield; ear protection; and a
dust mask.
WARNING – Indicates a potentially hazardous
situation which, if not avoided,
could result in death or serious
injury.
When sweeping, adhere to all government rules, local
laws and other professional guidelines for your
sweeping application.
DANGER – Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury.
WARNING – Never raise the sweeper more than a
few feet off the ground. The sweeper
can tip back or the prime mover can
tip over causing death or serious
injury.
IMPORTANT – Used for instructions when machine
damage may be involved.
__________________________________________
Before leaving the operator’s area for any reason –
lower the sweeper to the ground, stop the prime
mover engine, set the brakes and remove the key from
the ignition.
Operation
CAUTION – A sweeper is a demanding machine.
Only fully trained operators or trainee
operators under the close supervision
of a fully trained person should use
this machine.
Minimize flying debris – use the slowest brush speed
that will do the job.
Keep hands, feet, hair and loose clothing away from
all moving parts.
Before sweeping:
• Learn sweeper and prime mover controls in an
off-road location.
Leave the brush hood (shield) and all other shields and
safety equipment in place when operating the sweeper
and prime mover.
• Be sure that you are in a safe area, away from
traffic or other hazards.
Be aware of the extra weight and width a sweeper
adds. Reduce travel speed accordingly.
• Check all hardware holding the sweeper to the
prime mover, making sure it is tight.
When sweeping on rough terrain, reduce speed to
avoid “bouncing” the sweeper. Loss of steering can
result.
• Make sure all hydraulic fittings and hardware are
tight.
• Replace any damaged or fatigued hardware with
properly rated fasteners.
Never sweep toward people, buildings, vehicles or
other objects that can be damaged by flying debris.
51-3845, 7/04
9
SAFETY SECTION
GENERAL INFORMATION
__________________________________________
Service & Repair
CAUTION – Do not modify the sweeper in any
way. Personal injury could result. If
you have questions, contact your
dealer or SWEEPSTER.
Repair or adjust the sweeper in a safe area, away from
road traffic and other hazards.
Before adjusting or servicing the sweeper – lower the
sweeper to the ground, stop the prime mover engine,
set the brakes and remove the key from the ignition.
When working on or around the sweeper, lower it to
the ground or secure it with transport chains or
cylinder-stop locks.
Stop the prime mover engine and cycle control levers
to release hydraulic pressure before servicing or
adjusting sweeper hydraulic systems.
WARNING – Escaping hydraulic fluid can have
enough pressure to penetrate the
skin, causing serious personal injury.
__________________________________________
51-3845, 7/04
10
SAFETY SECTION
SAFETY SIGNS AND LABELS
Care of Safety Signs
4. If a component with safety sign(s) affixed is re-
placed with a new part, make sure the new safety
sign(s) is (are) attached in the same location(s) as
the replaced components.
1. Keep safety signs clean and free from obstructing
material.
2. Clean safety signs with soap and water; dry with a
soft cloth.
5. Install new safety signs on clean surfaces only.
Spray a weak solution of soap and water on the
surface before applying the safety sign. This will
allow repositioning of the label. Squeegee any
bubbles to the outside edge.
3. Replace damaged or missing safety signs with new
signs from SWEEPSTER.
__________________________________________
Locations
Item
Part
Description
1.
2.
3.
4.
5.
6.
7.
50-0103
50-0104
50-0115
50-0145
50-0394
50-0076-1
50-0213
Label, Caution, To Avoid Injury
Label, Danger, Lock-Collar, Unlock-Collar
Label, Danger, Rotating Drive
Label, Warning, Rotating Broom
Label, Danger, Rotating Drive Line
Label, Caution, Pinch Point
Label, Warning, Rotating Driveline
51-3845, 7/04
11
SAFETY SECTION
Safety Signs & Labels
SAFETY SIGNS AND LABELS
Representations of Labels
Locations shown on page 10.
3. 50-0115
1. 50-0103
4. 50-0145
2. 50-0104
51-3845, 7/04
12
Safety Signs & Labels
SAFETY SECTION
SAFETY SIGNS AND LABELS
Representations of Labels (Continued)
Locations shown on page 10.
!
CAUTION
PINCH POINT
AVOID INJURY FROM
FRAME PIVOT AND STOPS.
Keep hands and feet away.
50-0076-1
6. 50-0076-1
7. 50-0213
5. 50-0394
51-3845, 7/04
13
Installation
OPERATION SECTION
INSTALLATION
Initial Installation
Follow the instructions for the subframe kit.
Install Front Hitch
1. Lift the hitch assembly (C, figure 1) slide onto the
slots on tractor (E). Lift back of hitch assembly to
frame (D) and install clevis pins (B), clevis pins (F)
and hair pins (A).
D
B
A
E
C
Many approved attachments have color coded
quick couplers to aid in installation. Match the
tractor quick coupler with the like colored
attachment quick coupler.
F
2. Install hydraulic cylinder hoses and fittings.
( figure 2)
Figure 1. Hitch to Tractor Installation
A. Hair Pin
D. Subframe
B. Clevis Pin, 5/8 x 1 13/16 E. Slots on Tractor
C. Assembly
F. Clevis Pin, 5/8 x 2 1/2
D
C
H
B
G
E
K
J
F
A
I
L
Figure 2. Cylinder/Hose Installation
A. Fitting, 1/8NPT x 1/2-20
B. Hose 30” Long
C. Fitting, Elbow, Swivel
D. Quick Disconnet
E. Hose 22” Long
F. Fitting, 1/8NPT x 7/16-20
G.Washer, Green
I. Hydraulic Cylinder
J. Pin
K. Hair Pin
L. Hitch
H. Washer, Yellow
51-3845, 7/04
14
Installation
OPERATION SECTION
INSTALLATION
F
E
C
A
B
D
E
Figure 1
D. Capscrews, 3/8-16 x 3/4
E. Carriage Bolts and Nuts
F. Set Collars
A. Drive Shaft
B. Support Bracket
C. Front Hitch
Install Long Drive Shaft
1. Slide the drive shaft (A, Figure 1) in from the front.
Line up the support bracket (B) with the front hitch
(C). Simultaneously line up the locking collar of the
drive shaft (A, Figure 12) with the gear drive of the
transmission (B).
2. Slide the support bracket (B, Figure 1) in to the
front hitch (C) about 1/2”. Connect the locking
collar (A, Figure 2). Pull back on the locking collar
(A) and slide the drive shaft fully onto the
transmission (B). Release the locking collar and
pull back on the drive shaft until the locking collar
locks onto the shaft.
B
A
4. Slide the support bracket (B, Figure 1) all the way
into the front hitch (C). The support bracket (B)
should be touching the front hitch. Tighten
capscrews (D).
Figure 2
A. Drive Shaft Locking Collar
B.Transmission Shaft
Note: If the support bracket does not touch the front hitch
(C, Figure 1) loosen the set collars (F) carriage bolts
and nuts (E) holding the bearing holders. Slide the
bracket to the front hitch (C) and tighten the set
collars (F) carriage bolts and nuts (E). Secure the
bracket with the capscrews.
51-3845, 7/04
15
OPERATION SECTION
INSTALLATION
Install Brush Head
1. Use tractor lift lever to lower hitch.
2. Position tractor in line with brush head.
3. Drive forward until hitch touches brush head, lift
hitch to engage implement.
4. Stop tractor engine, get off tractor, ensure pins
snap and engage into hitch. (figure 1.)
5. Connect drive line.
6. Connect cylinder to hitch and hydraulic lines to
tractor.
7. Place storage stands in up position.
Brush head not shown
Closed
(In)
Figure 1.
51-3845, 7/04
16
Before Operation
OPERATION SECTION
OPERATING TIPS
Operational Check
5. Carefully examine the sweeper clearance under
the tractor undercarriage.
CAUTION – Contact with the sweeper, moving
joints or material discharged by the
brush can cause serious injury.
Operate this implement from the
operator’s seat only. Make sure
bystanders are well clear of the
sweeper and sweeper discharge area
before angling or engaging the
sweeper.
6. If sweeper shields or other parts contact the
undercarriage of the tractor in any way, remove the
sweeper from the tractor and follow the tractor
operator’s manual to adjust the implement lift
height adjustment linkages, limiting the maximum
lift height.
7. Reinstall the sweeper.
1. Lubricate all U-joints and driveline components on
the sweeper with high-quality, multi-purpose
grease.
8. Start the tractor according to instructions in the
tractor operator’s manual.
9. Engage the tractor PTO with the engine at 1,000
rpm. Note any excessive noise, vibration or other
problems.
2. Start the tractor according to instructions in the
tractor operator’s manual.
3. Slowly raise the sweeper to the fully lifted position
with the implement lift.
10. Disengage the PTO, shut off the engine and
remove the key.
4. Stop the tractor and remove the key.
11. Correct any driveline problems before the unit is
put into service.
CAUTION – Do not get under the sweeper at
any time while sweeper is in the
raised position.
__________________________________________
51-3845, 7/04
17
Operating Instructions 4 WD hydraulic right
OPERATION SECTION
OPERATING TIPS
Operating Sweeper
Use the tractor lift lever to raise and lower the sweeper.
CAUTION – Operate this implement from the
operator’s seat only. Do not allow
other riders on the machine at any
time.
CAUTION – Operate this implement at a speed
that matches working conditions.
Be extremely careful when working
on banks or uneven terrain.
4 WD hydraulic right
4 WD hydraulic lower
4 WD hydraulic left
4 WD hydraulic lift
CAUTION – Operators must wear eye protection
(goggles, etc.) during operation.
For the most efficient operation, sweep with the tips of
the bristles like a broom – not with the sides of the
bristles like a mop. Adjust the brush contact accord-
ing to instructions in Adjust Brush Contact Area (page
25).
Control brush speed with the throttle. If the brush stalls
frequently, increase the engine speed slightly. Find the
right brush and travel speeds so you don’t have to
increase the brush speed suddenly to overcome a
stall. Under most conditions, too fast of brush speeds
result in debris coming over the hood onto the
operator.
For heavy material, reducing ground speed and
angling the brush fully right or left to gives the best
sweeping results. This allows the sweeper to discharge
material out of brush path area and prevents the “re-
sweeping” of material.
__________________________________________
Snow Removal
CAUTION – Foreign objects in snow may be
thrown farther than the snow itself.
Use the slowest brush speed that
will perform the job and always
remain aware of the sweeper
For specific tips, see Snow Removal, Lawn Thatching,
Leaf Raking and General Sweeping• in this manual
section.
Brush stands must be placed in the raised position
before sweeping.
discharge direction.
__________________________________________
CAUTION – Snow or ice build-up on the sweeper
hood can cause a loss of tractor
steering control. Regularly remove
any snow or ice from the sweeper
hood to prevent the excess weight
from affecting steering.
Sweeper Control
WARNING –Contact with the tractor, sweeper or
debris discharged by sweeper can
cause serious injury. Be sure by-
standers are completely clear of the
tractor, sweeper and sweeper
discharge area before operation.
Vary the brush speed and sweeper angle so the
sweeper throws material out of the sweeper path
whenever possible.
CAUTION – Always wear eye protection when
Faster brush speeds perform better on wet, heavy
snow or slush.
operating any sweeper.
Use the tractor PTO to start and stop the sweeper
brush.
This sweeper works best on snow depths of 6 in. (152
mm) or less, but almost any amount of snow can be
moved if ground speed is reduced. If snow carries over
to the rear of the brush, reduce speed and make a
second pass to produce a clean surface.
1. Start the engine and put the throttle lever at 1/3
speed.
__________________________________________
2. Engage the PTO.
3. To stop, disengage the PTO.
51-3845, 7/04
18
Operating Instructions
OPERATION SECTION
OPERATING TIPS
Leaf Raking
Lawn Thatching
Carry the sweeper with implement lift slightly raised to
limit contact with the grass.
NOTE – Your sweeper is provided with a
polypropylene brush. Brushes with 1/2 poly–
1/2 wire or full wire sections may damage
lawns by pulling out the live grass. Brushes
made with wire are not recommended for lawn
thatching.
Use slower brush speeds and slow-to-medium travel
speeds when raking leaves.
For best results, rake leaves on days when leaf mois-
ture is high.
__________________________________________
Carry the sweeper with the implement lift slightly raised
to limit ground contact. Brush bristles should barely
touch the ground while sweeping under load.
General Sweeping
Slower brush speeds and slower ground speeds are
more suitable for lawn thatching. This gives the brush
time to pull out the dead grass and minimizes the
bouncing of the brush head, which can cause lawn
damage due to excessive ground contact.
Minimize dust by reducing brush speeds and by
sweeping on days with high moisture. Try to keep wind
at your side or back. (Refer to figure 1.)
For light material, angle the sweeper 30° left or right.
Minimize dust by sweeping when moisture is high (but
not wet).
__________________________________________
Prevent damage to the sweeper by removing large
foreign objects.
__________________________________________
Preferred Wind Directions
When Sweeping
Figure 1
51-3845, 7/04
19
OPERATION SECTION
OPERATING TIPS
Troubleshooting
If Material Piles in Front of Sweeper
• Decrease travel speed
• Increase the engine rpm
• Make more than 1 pass
• Raise the brush to decease the contact area
• Increase the sweeper angle
__________________________________________
If Brush Wears Unevenly
• Check for material wrapped around the brush
• Clean underneath the hood
__________________________________________
If Driveline Wears Quickly
• Decrease travel speeds
• Make more than 1 pass, especially in deep, heavy
materials
• Avoid ramming piles
• Lack of lubrication – lubricate more often
__________________________________________
51-3845, 7/04
20
Removal/Storage
OPERATION SECTION
REMOVING SWEEPER AND HITCH
Sweeper & Hitch Removal
NOTE – Whenever removed, install clevis pins, hitch
pins, clips and hardware into the sweeper and
hitch for storage.
1. Install stands in storage position and fully lower
the attachment lift.
2. Disconnect the drive shaft by pulling back on the
locking collar and then pulling the shaft off.
3. Disconnect hydraulic hoses. Disconnect hairpins
and remove clevis pins. Slide hitch assembly off
the slots on the tractor.
4. Detach the sweeper from the sweeper hitch by
moving the shot pins into open position.
5. Lower the hitch to the ground and back out.
Brush head not shown
Lock
Open
(Out)
51-3845, 7/04
21
MAINTENANCE SECTION
DAILY MAINTENANCE
Maintenance
CAUTION – Allow only trained personnel to
operate or service this implement.
Know and understand all precau-
tions before assembly, service or
operation. Also read and understand
all safety precautions in the tractor
operator’s manual.
Lubrication
Gearbox
figure 1
Check gearbox lubricant every 25 hours.
1. When oil is cold, remove the top plug (figure 1).
Make sure oil is level with the plug hole.
2. If needed, add gear oil meeting SPI GL5 80w-90
classification. Do not exceed a 50/50 mix with
synthetic oil.
3. Reinstall the plug.
NOTE – You do not have to change gearbox oil.
Drive Shaft
figure 2
After every 8 operating hours, lubricate 3 grease points
(figure 2) on the drive shaft with multi-purpose grease.
Do not over grease universal joints.
Bearings
All bearings on the sweeper are permanently lubricated
for long life and require no lubrication.
Drive Chain
Lubricate with oil when changing brush sections.
__________________________________________
Tractor Air Filter
Due to dusty conditions, check the tractor air filter
often. Further instructions appear in the tractor
operator’s manual. Be sure to follow the recommenda-
tions for “extreme conditions” as the air filter can be
affected by dust and other debris raised by the
sweeper.
__________________________________________
51-3845, 7/04
22
Maintenance
MAINTENANCE SECTION
DAILY MAINTENANCE/BRUSH REPLACEMENT
Daily Maintenance Checks
Hardware – Check and tighten all hardware on the
sweeper, including factory-installed hardware.
Brush Contact – Check brush contact. (See Adjusting
Brush Contact Area, page 25.)
__________________________________________
Brush Replacement
Replace sections when worn to 14 in. (356 mm) in
diameter.
Figure 2
NOTE – Replacing brush sections can be
accomplished more easily with the sweeper
mounted on the tractor than with it on the
ground.
Drive End
1. Remove the chain guard (figure 1) from the right-
hand side of the brush head.
2. Disconnect the drive chain (figure 2) at the master
link. Remove the chain from the large sprocket.
3. Loosen 2 set screws on each lock collar located at
each end of the brush core (figures 3 and 4).
Figure 3
4. Remove the chain guide plate (figure 5).
Bearing End
Figure 4
Figure 1
Figure 5
51-3845, 7/04
23
Maintenance
MAINTENANCE SECTION
BRUSH REPLACEMENT
5. Remove the snap ring from the large sprocket
(figure 6).
6. Remove the lock hub by removing all set screws
and then inserting the screw indicated in figure 7.
7. Remove the sprocket, washer and key from the
brush core.
8. Loosen 2 M8 hex nuts that retain the bearing on
the bearing end of the core (figure 8).
9. Slide the core to the toward the bearing end to
allow additional space on the other side.
Figure 6
10. Remove 3 M8 carriage bolts, lock washers and hex
nuts that retain the drive end bearing and flanges
(figure 9).
11. Pull the brush core from the brush frame (figure 10).
12. Remove 3 screws to take the retainer plate off the
core.
13. Remove old sections.
Continued on next page
Figure 7
Figure 9
Figure 8
Figure 10
51-3845, 7/04
24
Maintenance
MAINTENANCE SECTION
BRUSHREPLACEMENT
14. Install new sections by doing the following.
a. Number the tubes on the core as 1, 2, and 3
(figure 1).
b. Slide the first section onto the core with the
drive pins (figure 2) on both sides of tube 1.
Make sure that the drive pins face up.
NOTE – When using 1/2 poly–1/2 wire sections, place
a poly section first and last on the core to
prevent damage to the hood, driveline and
frame.
figure 1
c. Place the second section on the core with the
drive pins on both sides of tube 2. Be sure the
drive pins face down.
d. Put the third section on with the drive pins
around tube 3. Be sure the drive pins face up.
e. Slide sections on until the core is full, making
sure to alternate the tubes used and the
direction of the drive pins.
15. Put the retainer halves on the brush head and
reinstall the screws.
Figure 2
16. Position the brush head in front of the brush hood.
22. Install the key, washer, sprocket, hub and snap
ring.
17. Place the bearing end of the brush core in the
bearing side of the brush head.
23. Tighten the hub onto the sprocket.
18. Place the drive end in the brush frame. The bearing
and flanges go between the brush frame and brush
core.
24. Clean and lubricate the drive chain. Then, install it.
25. Reinstall the chain guide plate.
19. Slide the core toward the bearing end.
26. Reinstall the chain guard. Insert a 1/8 in. (3 mm) or
smaller diameter pin punch through the hole in the
chain guard and into the idler to align the compo-
nents.
20. Install 3 M8 carriage bolts, lock washers and hex
nuts in the drive end bearing and flanges.
21. Tighten all set screws on lock collars.
27. Adjust the idler according to Adjusting Drive Chain
Idler (page 25). Adjust the brush by following
directions in Adjusting Brush Contact Area (page
25).
__________________________________________
51-3845, 7/04
25
MAINTENANCE SECTION
Maintenance
ADJUSTING DRIVE CHAIN IDLER/BRUSH PATTERN
Adjusting Drive Chain Idler
1. Clean debris off the idler adjustment screw
(figure 1) located on the drive end of the brush
head.
2. Disconnect the quick release end of the sweeper
drive shaft.
3. Raise the sweeper several inches off the ground.
4. Loosen the jam nut.
Figure 1
5. While rotating the brush manually, turn the idler
screw by hand until it will not tighten any more.
IMPORTANT – Avoid damage to the sweeper drive
mechanism. Tighten the idler by hand
only. Using a wrench or other tool can
result in overtightening the idler which
can damage the drive chain and other
parts.
6. Tighten the lock nut.
__________________________________________
Figure 2
Adjusting Brush Contact Area
Replacing Shear Bolt
NOTE – Keep tires at the correct pressure.
1. Drive to a dirty section on a hard surface.
Replace the shear bolt in the end of the drive shaft if it
breaks.
1. Remove any remaining parts of the broken shear
bolt.
2. Set the brush on the ground and run it 30 seconds
without moving the tractor.
2. Install a new shear bolt.
3. Stop, raise the brush head assembly, back away
and park the tractor.
3. Check the condition of the snap ring retaining the
drive shaft. Replace if it is broken or damaged.
__________________________________________
4. Measure the path cleared. If the sweeper is ad-
justed correctly, the path will be 2-3 in. (51-76 mm)
wide.
Safety Labels
5. Adjust brush contact area with the brush adjust-
ment knob (figure 2). To make the path wider, lower
the brush head assembly by turning the knob to
the left (counterclockwise).To create a narrower
path, raise the brush head assembly by turning the
knob to the right (clockwise).
Replace worn or damaged safety labels before the
sweeper is operated. If any safety labels become
damaged when parts are repaired, replace those
labels before operating the sweeper.
Keep all safety labels clean so they are easy to read.
__________________________________________
Order replacement safety labels (shown on pages 11-
12 of this manual). Replacement safety labels are
supplied at no charge.
See page 10 for the location of safety labels on the
sweeper.
__________________________________________
51-3845, 7/04
26
Notes
51-3845, 7/04
27
Parts
M26 Series
Table of Contents
Parts List ............................................................ 28-32
Brush Head ........................................................ 28-29
Hitch ....................................................................... 30
Mounting Hardware ................................................ 31
Sections.................................................................. 32
51-3845, 7/04
28
Brush Head
PARTS SECTION
BRUSHHEAD ASSEMBLY
Item Part
Qty Description
Sheet, Hood, Side, Left
Item Part
Qty Description
36. 13-5741
37. 13-5742
38. 13-8384
39. 13-8390
40. 13-8396
41. 13-8420
42. 13-8472
43. 13-8557
44. 13-9456
45. 13-9457
46. 13-9591
47. 13-9652
13-8391
48. 13-9655
13-8415
49. 13-9659
13-5743
50. 13-9698
51. 13-9817
52. 13-9818
53. 50-0014-11 Label, Caution, Read Manual
54. 50-0076-12 Label, Caution, Pinch Point
55. 50-0103
56. 50-0104
57. 50-0115
58. 50-0213
59. 50-0391
60. 50-0718
63. 07-3270
64. 07-4033
65. 07-4668
66. 13-8385
1
1
1
2
1
1
3
2
2
1
1
1
1
1
1
1
1
2
1
2
1.
01-5847
24 Section, 26, 8 P, Convoluted, Black
(4 Ft Broom)
31 Section, 26, 8 P, Convoluted, Black
(5 Ft Broom)
Sheet, Hood, Side, Right
Knob, Pattern, Adjustment, 5/8-8
Bushing, Brush Head, Swing
Plate, Retainer, Core
2.
3.
4.
5.
6.
7.
8.
9.
06-0433
06-0434
06-0435
06-0436
07-0193
07-0210
07-1075
07-1090
1
1
Sprocket, 50B11 x 1 Bore x 1/4 Key
Sprocket, 50B36, Tapered Bore
Hub, Taper, 1.00 Bore, 1/4 Key
Chain, #50, 78 Pitches
Pin, Clevis, Gr2, 3/8 x 1 1/8
Clip, Hairpin, 14Ga x 1.75
Weld, Idler
Assembly, Plate, Locking
Assembly, Support, Hood
Plate, Keeper
1
1
1
1
7
1
Plate, Spacer, Chain Guide
Weld, Cover, Brush Frame Side
Weld, Core (4 Ft Brush)
Weld, Core (5 Ft Brush)
Shaft, Drive Line (4 Ft Brush)
Shaft, Drive Line (5 Ft Brush)
Sheet, Hood (4 Ft Brush)
Sheet, Hood (5 Ft Brush)
Key, 1/4 x 1/4 x 15/16
Weld, Stand, Holder
Rivet, Pop, Gr2, 3/16 x 3/4
Pin, Clevis, Gr2, 1/2 x 5, Grip 4.75
10. 07-1679 10 Plug, Cap, Plastic, for 5/16 Hole
11. 07-1810 Nut, Lock, Center, Gr2, 5/16-18
12. 07-2950 10 Bolt, Carriage, Cl8.8, M8 x 1.25 x 20
13. 07-2952 32 Screw, Cl10.9, M6 x 1 x 20
14. 07-2954 10 Nut, Hex, Gr5, M8 x 1.25
1
15. 07-2956 30 Nut, Insert, M6 x 1 Grip .027-.165
16. 07-3273
17. 07-3922
18. 07-3939
19. 07-4089
20. 07-4090
21. 07-4417
22. 07-4473
23. 07-4484
24. 07-4522
25. 07-4523
26. 07-4656
27. 07-4987
8
2
3
1
2
1
1
1
2
4
1
1
Washer, Lock, Split, Medium, 5/16
Nut, Insert, M6 x 1, Grip .165-.251
Ring, Snap, 1 x .078
Screw, Tap, 5/16-18 x 2.25
Washer, 1.5 x 1 x .075
Tube, Rd, Stand
1
1
1
2
2
1
2
3
3
2
Label, Caution, Avoid Personal Injury
Label, Danger, Lock Collar
Label, Danger, Rotating Drive Line
Label, Warning, Rotation, Shaft
Label, Warning, Rotating Broom
Label, Serial Number
Nut, Hex, Nylock, Gr8, 5/16-18
Nut, Hex, Nylock, 1/4-20
Screw, HHC, Gr2, 1/4-20 x 2 1/2
Bolt, Shear
Chain, Guide
Shield, Drive shaft
Screw, Panhead, 8-18 x 1/2
Clip, Hairpin, .162 x 3.43
Plug, Cap, Plastic, Black, 1 x .51
Tag, Plastic, Red, Remove Before Use
Shield, Drive shaft, with Hole
(4 Ft Broom)
07-4472
1
Shield, Drive shaft, with Hole
(5 Ft Broom)
28. 08-0005
29. 08-0008
30. 08-0148
31. 11-5131
2
4
3
1
Flange, Bearing, 2 Holes
Bearing, Flange, 3 Hole
Bearing, 1 RD, with Collar/Set Screw
Assembly, Mounting, QA
32. 13-10018 1 Weld, Frame, Brush (4 Ft Brush)
13-9593
33. 13-1321
34. 13-5723
35. 13-5740
1
1
1
2
Weld, Frame, Brush (5 Ft Brush)
Key, 1/4 x 1/4 x 2
Weld, Adjustment, Brush Head
Plate, Retainer, Bushing, Swing
51-3845, 7/04
29
PARTS SECTION
Brush Head
BRUSHHEAD ASSEMBLY
Brush Head
51-3845, 7/04
30
Angling Rod
PARTS SECTION
HITCH ASSEMBLY
22
4
2
21
11
17
20
6
16
10
18
14
8
1
5
3
12
7
19
13
9
FINAL INSTALLATION VIEW
OF 11-1533
Item Part
Qty Description
Item Part
Qty Description
12. 07-3676
13. 07-4037
14. 08-0131
16. 11-5133
17. 13-13159 1 Weld, Mounting, QA
18. 13-13164 1 Weld, Swing, Frame
19. 13-4291
20. 07-2914
21. 13-9541
22. 50-0394
2
2
4
1
Screw, HHC, Gr8, 1/2-13 x 5
Nut, Hex, Nylock, Gr8, 1/2-13
Bearing, Caster
1.
2.
3.
4.
5.
6.
7.
8.
9.
05-1409
1
1
8
2
8
2
2
8
2
2
1
Gearbox, Omni, 3:1
Shaft, Drive
05-1291
07-0018
07-0699
07-1718
07-2843
07-3013
07-3015
07-4367
Screw, HHC, Gr8, 3/8-16 x 1
Pin, Cotter, Gr2, 1/8 x 1 1/4
Washer, Lock, Split, Medium, 3/8
Pin, Klick, 3/16 x 1, 5/8
Bushing, Caster
Kit, Mounting, Hardware
2
1
2
2
Weld, Caster, Fork
Bolt, Shear, Gearbox
Pin, Clevis, .75 x 1.11
Label, Danger, Rotating Drive Line
Spacer, Caster
Wheel, Caster, 6.25 x 5/8
Fitting, Zerk, 1/4-28, Self Tap
Nut, Hex, Nylock, Gr8, 1/4-20
10. 07-3112
11. 07-4033
Not Shown
11-5132
1
Kit, Hydraulic, Swing
51-3845, 7/04
31
PARTS SECTION
MOUNTING HARDWARE
Kit 11-5133 Mounting Hardware
#1709659 (QTY 2)
#1709660 (QTY 2)
#1960587 (QTY 2)
#1924366 (QTY 2)
11-5132 Kit Hydraulic Swing
Part #
Qty
1725359
1725049
1918452
1725322
1960033
919171
1
1
1
1
1
1
1
1
1
2
2
2
2
172320
1725318
1725319
173359
1725520
1726321
1726319
51-3845, 7/04
32
Notes
PARTS SECTION
SECTIONS
Item Part
Qty Description
1.
01-0924
1
Section, Set, 26, 8, Combination, Convoluted
51-3845, 7/04
33
Appendix
M26 Series
Table of Contents
Hardware and Torque Specifications ......................... 34
Warranty .............................................................. 35-36
51-3845, 7/04
34
Torque Values
APPENDIX
HARDWARE/TORQUE SPECIFICATIONS
Hardware Identification & Torque Specifications
Common Hardware Types
Torque Specification Chart
FOR STANDARD MACHINE HARDWARE (Tolerance 20%)
Hex Head Capscrew
Washer
No
Marks
Hardware
Grade
Lockwasher
Carriage Bolt
SAE Grade 2
SAE Grade 5
in/lbs
SAE Grade 8
in/lbs
Hex Nut
Size Of
in/lbs
Hardware ft/lbs
Nm.
2.1
2.3
3.1
3.5
7.6
ft/lbs
Nm.
ft/lbs
Nm.
Standard Hardware Sizing
8-32
8-36
19
20
30
31
43
49
8
10
17
19
30
35
50
55
75
3.4
3.5
4.9
5.5
10.9
13.6
23.1
25.8
40.8
41
43
60
68
12
14
25
27
45
4.6
4.9
6.8
7.7
16.3
19.0
34.0
34.0
61.2
When a washer or nut is identified as 1/2”, this is the
Nominal size, meaning the inside diameter is 1/2 inch; if a
second number is present it represent the threads per inch
10-24
10-32
1/4-20
1/4-28
5/16-18
5/16-24
3/8-16
3/8-24
7/16-14
7/16-20
1/2-13
1/2-20
9/16-12
9/16-18
5/8-11
5/8-18
3/4-10
3/4-16
7/8-9
27
31
66
76
11
12
20
23
30
35
50
55
65
75
90
100
160
180
140
155
220
240
When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the Nominal size, or body diameter is 1/2 inch; the
second number represents the threads per inch (16 in this
example, and the final number is the body length of the
bolt or screw (in this example 2 inches long).
8.6
15.0
16.3
27.2
31.3
40.8
47.6
68.0
74.8
88.4
102.0
122.4
136
217.6
244.8
190.4
210.8
299.2
326.4
The guides and ruler furnished below are designed to
help you select the appropriate hardware and tools.
47.6
68.0
74.8
50
70
80
68.0
95.2
108.8
149.6
163.2
204.0
231.2
299.2
326.4
525.0
571.2
816.0
897.6
102.0
122.4
149.6
163.2
204.0
244.8
353.6
408.0
544.0
598.4
788.8
110
120
150
170
220
240
386
420
600
660
Nut, 1/2”
90
Inside
Diameter
110
120
150
180
260
300
400
440
580
640
7/8-14
1-8
1-12
Screw, 1/2 x 2
900 1,244.0
Body
Diameter
870.4 1,000 1,360.0
NOTES
1. These torque values are to be used for all hardware
excluding: locknuts, self-tapping screws, thread forming
screws, sheet metal screws and socket head setscrews.
Body
Length
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque
values must meet this specification.
Wrench & Fastener Size Guide
1/2
DIA.
7/16
DIA.
3/8
5/16
1/4
1/4” Bolt or Nut
Wrench—7/16”
5/16” Bolt or Nut
Wrench—1/2”
3/8” Bolt or Nut
Wrench—9/16”
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
1/2” Bolt or Nut
Wrench—3/4”
51-3845, 7/04
35
APPENDIX
WARRANTY INFORMATION
C
C
P
P
D
P
p
i
p
i
Z
Z
A
A
S
S
51-3845, 7/04
36
Warranty Information
APPENDIX
WARRANTY INFORMATION
|
Bolens Lawn Mower 113 074A User Manual
Briggs Stratton Lawn Mower S50X User Manual
Craftsman Lawn Mower 917388191 User Guide
Craftsman Lawn Mower 917389052 User Guide
Ferris Industries Lawn Mower 5900591 User Guide
Hayter Mowers Lawn Mower RS 17 102H User Guide
Land Pride Lawn Mower DM36 Series User Guide
McCulloch Lawn Mower 96141014103 User Guide
Snapper Lawn Mower P21407T 2 User Manual
Woods Equipment Lawn Mower Accessory BSE4 User Guide