Rover Lawn Mower 50 60 User Guide

Owners Manual  
Gebrauchsanweisung  
Manuel du Propriétaire  
Manual del Propietario  
Handleiding  
Manuale Instruzioni  
MODEL 50, 60  
Petrol Lawnmower  
Motor-Rasenmäher  
Tondeuse à Gazon à Essence  
Cortadoras de Cesped a Gasolina  
Benzine Grasmaaimachine  
Falciatrice A Motore  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B
A
1
4
B
A
A
2
5
3
6
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
8
9
12  
1mm  
13  
14  
A
10  
15  
11  
16  
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rover Mowers Limited  
ENGLISH  
SAFETY INSTRUCTIONS  
Safety Instructions  
1. Training  
a. Read the instructions carefully. Be familiar with the  
controls and the proper use of the equipment.  
b. Never allow children or people unfamiliar with these  
instructions to use the mower. Local regulations may  
restrict the age of the operator.  
h. Do not mow excessively steep slopes.  
i. Use extreme caution when reversing or pulling the  
mower towards you.  
j. Stop the blade(s) ,if the mower has to be tilted for  
transportation when crossing surfaces other than grass  
and when transporting the mower to and from the area  
to be mowed.  
c. Never mow while people, especially children, or pets  
are nearby.  
d. Keep in mind that the operator or user is responsible  
for accidents or hazards occurring to other people or  
their property.  
k. Never operate the mower with defective guards or  
shields, or without safety devices, for example deflectors  
and/or grass catchers in place.  
l. Do not change the engine governor settings or overspeed  
the engine.  
2. Preparation  
m. Disengage all blade and drive clutches before starting  
the engine.  
n. Start the engine or switch on the mower carefully  
according to instructions and with feet well away  
from the blade(s).  
a. While mowing, always wear substantial footwear and  
long trousers.  
Do not operate the equipment when barefoot or  
wearing open sandals.  
o. Do not tilt when starting the engine or switching on  
the motor, unless the mower has to be tilted for  
starting. In this case, do not tilt it more than absolutely  
necessary and lift only the part which is away from the  
operator.  
b. Thoroughly inspect the area where the equipment is  
to be used and remove all stones, sticks, wires,  
bones and other foreign objects.  
c. WARNING- Petrol is highly flammable.  
p. Do not start the engine when standing in front of the  
discharge chute.  
q. Do not put hands or feet near or under rotating parts.  
Keep clear of the discharge opening at all times.  
r. Never pick up or carry a mower while the engine is  
running.  
s. Stop the engine and disconnect the spark plug lead:  
i. Before clearing blockages or unclogging the chute.  
ii. Before checking, cleaning or working on the mower.  
iii. After striking a foreign object. Inspect the mower for  
damage and make repairs before restarting and  
operating the mower.  
iv. If the mower starts to vibrate abnormally check  
immediately.  
t. Stop the engine  
i. Whenever you leave the mower.  
ii. Before refuelling.  
u. Reduce the throttle setting during engine run-out and if  
the engine is provided with a shut-off valve, turn off the  
fuel at the conclusion of mowing.  
Take the following precautions.  
i. Store fuel in containers specially designed for this  
purpose.  
ii. Refuel outdoors only and do not smoke while  
refuelling.  
iii. Add fuel before starting the engine. Never remove  
the cap of the fuel tank or add petrol while the engine  
is running or when the engine is hot.  
iv. If petrol is spilled, do not attempt to start the  
engine but move the machine away from the area of  
spillage and avoid creating any source of ignition  
until petrol vapours have dissipated.  
v. For reasons of safety the petrol tank and tank cap lock must be  
replaced if damaged.  
d. Replace faulty silencers.  
e. Before using, always visually inspect to see that the  
blades, blade bolts and cutter assembly are not worn or  
damaged. Replace worn or damaged blades in sets to  
preserve balance.  
f. On multibladed machines, take care as rotating one  
blade can cause other blades to rotate.  
4. Maintenance and storage.  
3. Operation  
a. Keep all nuts, bolts, and screws tight to be sure the  
equipment is in safe working condition.  
b. Never store the equipment with petrol in the tank inside  
a building where fumes may reach an open flame or  
spark.  
c. Allow the engine to cool before storing in any enclosure.  
d. To reduce the fire hazard, keep the engine, silencer,  
battery compartment and petrol storage area free of  
grass, leaves, or excessive grease.  
e. Check the grass catcher frequently for wear or  
deterioration.  
a. Do not operate the engine in a confined space where  
dangerous carbon monoxide fumes can collect.  
b. Mow only in daylight or in good artificial light.  
c. Avoid operating the equipment in wet grass, where  
feasible.  
d. Always be sure of your footing on slopes.  
e. Walk, never run.  
f. For wheeled rotary machines, mow across the face of  
slopes, never up and down.  
g. Exercise extreme caution when changing direction on  
slopes.  
f. Replace worn or damaged parts for safety.  
g. If the fuel tank has to be drained, do this outdoors.  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rover Mowers Limited  
ENGLISH  
1. SETTING UP  
1.1 Grass catcher assembly  
3. Press firmly down on the catcher top to lock the barbs into slots.  
Figure 1.  
1. Locate the catcher handle and align its front lugs with the slots  
in the top of the catcher and press firmly into position. Figure 1.  
2. Position the catcher top over the catcher bottom, aligning the barbs  
on the top with the slots in the bottom. Figure 1.  
4. Secure with two screws provided.  
2. BEFORE OPERATING  
2.1 Folding handles  
CAUTION  
l. Lockingknobs-Byturningtheseknobsthehandlebarscanbeeither  
locked in the operating position or folded for storage.  
2. Locking lever- Lift the lever to release the handle bars for folding  
or push the lever closed to lock handle bars in the operating position.  
Adjust the tension by turning the lock nut with a 1/2" AF  
spanner.  
Avoid premature engine failure by using a clean funnel  
and clean away any possible contaminants.  
2.4 Fuel  
1. Position the mower on a level surface in a well ventilated area and  
clean around the fuel tank cap.  
2.2 Handle bar height  
2. Using a clean funnel fill the fuel tank with unleaded petrol.  
3. Replace the fuel tank cap and clean away any spilt petrol.  
1. Loosen the two nuts (A) at the base of the handle bars on both sides  
of the mower using a 1/2" AF spanner. Figure 2.  
2. Move the handle bars to the required position and tighten the handle  
bars nuts.  
2.5 Controls  
Throttle Control  
Marked for O (off)  
(slow)  
(fast) positions. Figure 3.  
2.3 Engine lubrication  
Operator Presense Control  
Handle moved towards the handle bars (I). Engine and blades are free to  
rotate. Handle released (0) engine and blades stop rotating. Figure 4.  
Self Propelled Drive Control  
Moved towards 1 (on) turns the clutch on and drives the mower forward.  
Moved towards O (off) turns the clutch off and stops the mower driving.  
Figure 5.  
Theengineoillevelmustbecheckedbeforeattemptingtostarttheengine.  
Refer to the engine manufacturer's instructions.  
1. Position the mower on a level surface and clean around the dip stick  
or oil plug.  
2. Remove the dip stick or oil plug.  
3. Using a clean funnel slowly add oil in accordance with the engine  
manufacturer's instructions.  
Powerstart  
Turnthekeytoon(I)positiontoengagetheelectricstarter.releasethekey  
when the engine starts and allow to return to the off (0) position. Figure  
16.  
4. Check the oil level by screwing in the dip stick or oil plug and  
removing again. When oil level is correct replace the dip stick.  
3. OPERATION  
3.1 Grass catcher  
CAUTION  
Installing the grass catcher  
With powerstart mowers if the engine fails to start after 3  
seconds of continuous cranking release the ignition key and  
wait10secondsbeforetryingtorestarttheengine. Iftheengine  
still fails to start check the fuel level, battery connections, and  
battery condition. If the engine is cranking slowly the battery  
may need charging, refer to section 6.3 for battery charging.  
1. Raise the rear flap of the mower.  
2. Grasp the grass catcher by the top handle and position the grass  
catcher against the rear of the mower. Figure 6.  
3. Lower the rear flap so that the back edge of the flap hooks over the  
grass catcher.  
Removing the grass catcher  
3.4 To stop the engine  
1. Move the throttle control lever to the stop position. O  
2. Release the “Operator presence control handle”.  
3. Turn the fuel tap off where fitted.  
1. Grasp the grass catcher top handle and lift up.  
2. Raise the rear flap of the mower to release grass catcher.  
3. Lift the grass catcher clear of the mower and lower the rear flap.  
4. Remove the ignition key on Powerstart mowers.  
3.2 Adjusting the height of cut  
3.5 Drive engagement - Self propelled mowers  
1. Grasp the height of cut lever (A) and apply an outward pressure to  
release the lever from the rack (B). Figure 7.  
2. Move the lever while holding out to the required height of cut  
position and engage the lever in the rack by releasing the lever.  
1. Starttheengineandsettheenginespeedtotherequiredgrasscutting  
speed.  
2. Push forward on the clutch engagement lever to engage the self-  
propelled drive to the rear wheels. Fig. 5.  
3. To disengage the self-propelled drive release the engagement  
lever and allow it to return to the disengaged position.  
3.3 To start the engine  
CAUTION  
1. Move the Throttle Control lever to the fast position.  
2. Press the primer bulb firmly 5 times.  
3. Grasp the 'Operator presence control handle' and hold against the  
handle bars. Refer engine manufacturers instructions. Fig. 4.  
4. Grasp the starter handle and pull, or turn the ignition key on  
Powerstart mowers.  
Do not hold the engagement lever in a semi-engaged position to  
slip the clutch as this will lead to excessive clutch wear.  
3.6 Blade Brake Control  
5. After engine starts, move the Throttle Control to the slow position.  
The mower engine is fitted with a blade brake system. When the  
“Operator Presence Control” is held against the handle bars the brake is  
off (0). When the Operator presence control is released the blade brake is  
on (I).  
Page 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rover Mowers Limited  
ENGLISH  
4. MAINTENANCE GENERAL  
CAUTION  
4.1 Engine air cleaner  
Do not over tighten the spark plug as engine damage may occur.  
Refer to the engine manufacture's instructions for detailed cleaning  
instructions.  
The engine air cleaner element must be serviced after each 25 hours of  
normal mowing. The element must be serviced more regularly if the  
mower is used in dusty conditions.  
4.4 Cutting assembly  
1. Disconnect the spark plug lead.  
2. Move the height of cut lever to the high cut position, and fold the  
handle bars.  
4.2 Snorkel air intake  
3. Tilt the mower so that the spark plug is up.  
4. Inspect the cutting assembly for damage and wear.  
5. Check the disc retaining bolts. Tighten the centre bolt to 48 Nm.and  
the three concentric bolts to 14 Nm.  
The snorkel air cleaner element must be serviced after each 50 hours of  
normal mowing. The element must be serviced more regularly if the  
mower is used in dusty conditions.  
6. Return mower to its normal position and replace the spark plug lead.  
1. Disconnect the air tube from the element holder.  
2. Remove the holder cap.  
WARNING  
3. Remove the cartridge and tap gently on a flat surface to remove dirt.  
4. Replace element in holder and replace holder cap.  
5. Replace the air tube to the bottom of the element holder.  
Remove the spark plug lead before working on cutting assembly.  
Do not work on the cutting assembly without wearing gloves.  
4.5 Blade change  
NOTE: Quantum engines fitted with a Remote snorkel air  
intake are not fitted with an air cleaner element. Note the  
air cleaner element on this model is located on the engine.  
1. Disconnect the spark plug lead.  
2. Set the mower to the high cut position.  
3. Lift the rear flap on rear catcher mowers and prop open the flap to  
give access to the blades.  
Tilt utility mowers so that the spark plug is up.  
4. Remove the blade, blade retaining bolts, nuts and washers and  
discard. Retain only the ‘D’ plates.  
CAUTION  
Do not allow dirt to enter the air tube, engine damage may occur.  
Check the condition of the air tube regularly and replace if  
damaged.  
5. Fit new blades, blade bolts, washers, and nuts in sets to maintain  
balance. Figure 8.  
6. Tighten the blade nuts to 16 NM. Check the blades are free to move  
when the blade nut is tensioned.  
4.3 Spark plug  
7. Remove the flap prop or lower the mower to the ground and replace  
the spark plug lead.  
For best results remove and check the condition of the spark plug every  
25 hours of use.  
4.6 Throttle control  
1. Stop the engine and remove the spark plug lead.  
Each 25 hours of mowing use a small amount of light oil to lubricate  
the throttle control lever.  
2. Clean dirt from around the spark plug and remove the spark plug.  
3. If a new spark plug is required use a Champion RJ19LM or  
equivalent and set the electrode gap at 0.7 to 0.8 mm.  
4. Screw the spark plug into the engine and tighten to 20NM.  
5. MAINTENANCE - Self propelled mowers  
5.3 Rear drive chain inspection  
5.1 Drive chain lubrication  
1. Remove the spark plug lead.  
1. Remove the spark plug lead.  
2. Remove the cover plate screws (a) and lift off the cover plate (b).  
Figure 9.  
2. Remove the drive shaft cover plate retaining screws (a) and remove  
cover plate (b). Figure 11.  
3. Support the rear wheels off the ground to enable the drive to be  
rotated.  
3. Remove the stone guard retaining screws (c) and remove the stone  
guard. Figure 11.  
4. Use SAE 30 oil and lubricate the drive chains at point (a) whilst  
the chain is being rotated. Figure 10.  
4. Remove the chain guard nuts (d) and slide the chain guard out of the  
way. Figure 12.  
5. Replace the chain cover plate and secure.  
6. Replace the spark plug lead.  
5. Inspectthedrivechainandaxlesprocketandreplaceiffoundtohave  
excessive wear.  
6. Replace the stone guard and drive shaft axle plate.  
7. Replace the spark plug lead.  
5.2 Drive chain adjustment  
Front drive chain  
1. Remove the spark plug lead.  
2. Remove the cover plate.  
5.4 Clutch adjustment  
3. Loosen the chain tensioner bolt (b) and move the chain tensioner to  
give a 3 mm deflection on the drive chain. Figure 10.  
4. Tighten the chain tensioner bolt and rotate the drive wheels to check  
the drive chain for tight spots.  
1. Remove the spark plug lead.  
2. Loosen the locknut (a) and turn the adjuster (b) clockwise until the  
clutch is felt to drag. Figure 13.  
3. Back off the adjuster anti-clockwise 2-3 turns and retighten locknut  
(a).  
5. Replace the cover plate.  
4. Replace the spark plug lead.  
Rear drive chain  
1. Remove the spark plug lead.  
2. Loosen the rear drive chain tension nut (c) and slide it upwards to  
tighten the rear drive chain. Figure 9.  
3. Retighten the rear drive chain tensioner nut and rotate the rear drive  
wheels to check for tight spots.  
4. Replace the spark plug lead.  
Page 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rover Mowers Limited  
ENGLISH  
5. MAINTENANCE - Self propelled mowers  
n
r
5.5 Clutch lining inspection  
5. Lubricate the slot at the centre of the drive pinion (d). Figure 15.  
6. Replace the wheel plug and wheel cap.  
7. Replace the spark plug lead.  
1. Remove the spark plug lead.  
2. Remove the cover plate as explained in section 5.1 “Drive chain  
lubrication”.  
o
3. Check the thickness of the friction material. Figure 13. If thickness  
of the friction material is less than 1mm the clutch plate should be  
replaced by an authorised Rover Mowers Limited Dealer.  
5.7 Drive wheel cleaning  
1. Remove the spark plug lead.  
2. Support the rear wheels off the ground and remove the wheel cap.  
3. Remove the ratchet plate (c) retaining the wheel to the axle.  
Figure 15.  
5.6 Drive pawl lubrication  
r
4. Remove the wheel from the axle and clean the inside of the wheel  
hub.  
5. Replace the wheel and retain using a new ratchet plate.  
6. Replace the wheel plug and wheel cap.  
7. Replace the spark plug lead.  
1. Remove the spark plug lead.  
2. Support the rear wheels off the ground.  
3. Remove the rear drive wheel cap (a) and the wheel plug (b). Figure  
c
14.  
o
u
4. Rotate the drive wheel to align the drive pinion with the wheel plug  
hole.  
g
n
6. MAINTENANCE - Powerstart Mowers  
6.1 Battery removal  
c
1. Remove the two retaining screws from each side of the battery  
support box and remove the front cover.  
2. Remove the battery from the support box and simultaneously  
disconnect the wiring loom from the battery terminals.  
2. Connect the battery charger to a suitable mains  
power outlet and switch on.  
3. Whenchargingiscompleteafter10to16hours,switchoffthepower  
outlet and disconnect the battery charger from the power outlet.  
4. Disconnect the battery charger leads from the battery and refit the  
battery to the mower.  
o
o
n
6.2 Battery installation  
1. Connect the mower wiring loom to the battery with the red lead  
attached to the positive (+) terminal of the battery and the black lead  
to the negative (-) terminal of the battery.  
2. Fit the two rubber blocks to each end of the battery and place the  
battery complete with the rubber blocks into the battery support box  
with the battery terminals closest to the centre of the mower.  
3. Refit the battery support box front cover and retain with the two  
screws.  
6.4 Care and handling  
d
d
t
1. Do not disassemble the battery, as it’s strong acid electrolyte may  
burn your skin or clothes.  
2. Do not short out the battery terminals, as this may burn the terminals  
and cause damage to the equipment.  
3. Do not incinerate the battery to depose of them.  
The battery may explode if exposed to fire.  
4. Cleanthebatterywithadrycloth only, never useoil, petrol, thinners  
or any other petrochemical.  
6.3 Battery charging  
A new battery when supplied with the mower may not be fully  
charged to maximum capacity. The battery should have an initial  
charging period of 10 to 16 hours. To charge the battery it must be  
removed from the mower first.  
5. Handle the battery with care. If the battery is dropped and the case  
is damaged the acid electrolyte (sulphuric acid) may leak out. Wipe  
up leaking acid with a cloth and neutralise acid with an alkaline  
solution.  
6. In the event of electrolyte coming into contact with the skin,  
immediately flush with water and seek medical attention.  
o
m u  
CAUTION  
Use only an approved battery charger supplied by the mower  
dealer which has been designed for use with this battery.  
e
n
u
t
1. Connect the battery charger to the battery with the  
red lead (positive) to the positive (+) terminal of the  
battery and the black (negative) lead to the negative  
(-) terminal of the battery.  
n
m o  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rover Mowers Limited  
7. SPARE PARTS  
26  
7.1 Series 85000, 86000 and 96000 base spare parts  
1
2
3
4
5
6
7
8
A03300  
A03510  
A03456  
A03325  
A03455  
A03126  
A10148  
A02591  
A03515  
A03514  
A03516  
A02051  
A01486  
A00293  
A01716  
A03830  
A03930  
A00673  
A10154  
A10140  
A10527  
A03450  
A03459  
A03320  
A03353  
A03414  
A03306  
A03743  
Base  
1
1
1
1
1
2
1
1
1
1
2
1
1
1
1
4
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
46  
47  
48  
49  
50  
51  
52  
53  
A03492  
A03409  
373109  
A03092  
S2501116  
290112  
A02127  
*
A04052  
A03549  
A03323  
A010141  
A03313  
A03250  
A10284  
A03336  
A02066  
A03319  
A03303  
A10381  
A03604  
A02071  
A02235  
A03472  
A03927  
A04108  
A04099  
A04111  
Decal- sound level  
Nameplate  
Tension washer  
Ratchet plate  
Ratchet plate  
Poprivet- 73 AS 6-4 blind  
Taptite- 3/8" - 16 HWH x 1" Ind.hex.W/H Duo.  
Decal- Model  
Self tapping screw- 10 x 5/8" pan ph/head2  
1
1
4
4
2
Height adjustment rack  
Rear Flap  
Spring- rear flap  
Handle- rear flap  
Pivot bush  
Conbar assembly  
Conbar spring  
Axle bracket- RH.  
Axle bracket- LH.  
Clamp bolt  
Woodruff key  
Disc boss  
Disc assembly  
Backplate  
Blade- standard  
Blade- Mulch N Catch  
Blade bolt kit  
10  
3
1
9
10  
11  
12  
13  
14  
15  
16  
16  
17  
18  
19  
19  
20  
21  
22  
23  
24  
25  
26  
Cable clip  
1
1
1
2
1
1
1
2
2
1
1
1
2
2
1
1
2
2
2
Plug chain slot- model 50  
Rear axle assembly- model 50  
Rear axle bush- model 50  
Plastic handle  
Height adj. lever assembly  
Packing plate  
Rivet  
Rear wheel assembly  
Grass deflector  
Rear stoneguard- Mod. 50  
Rear stoneguard- Mod. 60  
Rivet- 73 SS 4-3  
Nyloc nut- 1/4" unc.  
Decal- turbothrust  
Nose comb  
2
1
1
1
2
4
2
8
4
1
1
Disc bolt kit  
Front axle assembly- professional  
Front axle assembly- professional  
Front axle bush  
Wheel seal  
Front wheel assembly  
Wheel bearing  
Wheel cap  
Rivet  
Pivot rod  
Decal- Warning  
Washer- 3/16" x 3/4"  
Screw  
PAGE 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rover Mowers Limited  
7. SPARE PARTS  
7.2 Handle bar spare parts  
1
2
3
3
4
5
6
7
8
9
A03802 Handle bar-  
14  
15  
A04045 Flanged nut- 5/16" unc.  
A02223 Nyloc nut- 5/16" unc.  
A03317 Lower handle bar  
A03583 Throttle cable- Mod. 50  
A03326 Throttle cable- Mod. 60  
A10016 Throttle control assembly  
A02849 Lock handle  
A03307 Draw bolt  
A03500 Cable clip  
A03518 Plug spanner  
A10144 Grass catcher assembly  
16 A10523 Bale assembly CE  
17 A10524 Bale assembly CE  
18 A10503 Handle assembly CE  
19 A03739 Handle grip CE  
20 A02521 Spacer CE  
21 A03722 Brake cable- mod. 50,60  
22 A03733 Rope stop CE  
23 A02235 Nyloc nut- 1/4" unc.  
10 A03324 Mesh  
11 A03447 Handle  
24 A04083 Screw - 10 x 19mm Pan Head  
25  
12  
13  
A02260 Roll pin- 1/4" x 3/4"  
A02028 Setscrew- 5/16" x 5/8" unc.W/Face.  
26  
27 A03622 Decal  
PAGE 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rover Mowers Limited  
7. SPARE PARTS  
n
.
.
n
.
.
.
.
.
.
.
7.3 Self propell
. e  
48  
49  
50  
A02078  
A02081  
A02235  
Setscrew- 1/4" x 1/2" unc.hex  
Setscrew- 1/4" x 1-3/4" unc.hex  
Nyloc nut- 1/4" unc.  
1
2
3
4
5
6
7
7
8
A02102  
A10177  
A03365  
A07822  
A03314  
A03391  
A03383  
A10381  
A03393  
A02090  
A03373  
A03371  
A03372  
A03361  
A07675  
A10172  
A03366  
A03394  
A02069  
A03368  
A03382  
A03353  
A03352  
A03441  
Washer- Avdel 7601/0010  
Clutch lever  
Clutch cable  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
A03414  
A03369  
A03377  
A03364  
A03367  
A03360  
A10171  
A03358  
A10170  
A03359  
A03550  
A03363  
A03370  
A04052  
A03552  
A03551  
A03386  
A02070  
A03354  
A03376  
A03375  
A03250  
A02146  
A02214  
Wheel cap  
Drive shaft  
Rear drive chain  
Cable support bracket- RH  
Chain tensioner  
51 S2491162 Nut- 1/4" unc.square pressed  
Cable tie  
52  
53  
54  
55  
56  
A02001  
A03092  
A02030  
A02209  
A02044  
Nut- 1/4" unc.hex  
Rear axle support  
Stoneguard mount bracket  
Rear stoneguard- 96012  
Rear stoneguard- 86012, 86040  
Drive shaft cover  
Circlip- 1400/12  
Pawl retainer washer  
Drive pinion- RH  
Pawl  
Bearing- 6001 DDU  
Nylon bush  
Rear axle assembly  
Rear chain guard  
Felt seal  
Roll pin- 1/8" x 3/4"  
Rear drive shaft sprocket  
Dust seal  
Wheel bearing  
Geared wheel hub  
Washer plate  
Washer- Avdel 7301/0016  
Washer- 5/16" x 5/8" x 18g.flat  
Washer- 1/4" x 5/8" x 18g.flat  
Washer- 1/4" internal shakeproof  
Tension washer  
Clutch engagement bush  
Driver clutch plate  
Clutch spring  
Driven clutch plate  
Clutch support shaft  
Drive chain housing- LH  
Cable support bracket- LH  
Drive pinion- LH  
Self tapping screw- 10 x 5/8" pan ph/head  
Chain guard cover plate  
Drive chain housing- RH  
Felt seal  
Roll pin- 3/16" x 7/8"  
Sprocket PTO.  
57 S373109  
58 A10146  
59 S2501108 Washer- Avdel 7301/0008  
60  
61  
62  
9
Wheel assembly  
e
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
A10284  
A02118  
A03336  
Height adjustment lever assembly  
Rivet- 3/4" x 1/4" flat head  
Plate  
n
63 S3521047 Wheel plug  
64  
65  
66  
67  
68  
69  
70  
71  
72  
A03470  
290112  
A03390  
A03384  
A10524  
A10503  
A03739  
A02521  
A03604  
Chain guide  
Rivet- 73 AS 6-4 blind  
Clutch plate lining  
Tyre  
Bale assembly CE  
Handle assembly CE  
Handle grip CE  
Spacer CE  
l
Front drive chain  
Pivot rod  
Handle  
Setscrew- 1/4" x 3/4" unc.hex  
Setscrew- 1/4" x 5/8" unc.hex  
m
Rear extension- Mod. 60  
PAGE 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rover Mowers Limited  
7. SPARE PARTS  
7.4 Powerstart spare parts - Series 85000, 86000  
19 A03610  
20  
Foam block  
1
2
3
4
5
6
7
8
9
A03802  
A10016  
A03581  
A03557  
A03560  
A07679  
A03741  
A03565  
A03559  
Upper handle bars-Mod 60  
Throttle control assembly  
Throttle cable- Quantum  
Key start housing  
21 A10524  
22 A10503  
23 A02521  
24 A03739  
25 A03732  
26 A03733  
27  
Bale assembly- Mod 60 CE  
Handle assembly Mod.60- CE  
Spacer  
Key start switch  
Handle grip- CE  
Ignition key  
Cable clip- CE  
Wiring loom- Mod 60 CE  
Cable clamp  
Rope stop- CE  
Battery  
28 A02235  
29 A04083  
30  
30 A03722  
31 A03756  
Nyloc nut- 1/4" unc.  
Screw- 10 x 3/4 pan head  
10 A03558  
11 A03556  
12 A03563  
13 A02083  
14  
15  
16  
17  
18  
Battery block  
Battery support box  
Decal- caution  
Brake cable- mod. 60  
Switch Plate  
Setscrew- 5/16" x 3/4" unc.hex.  
Washer- 5/16" x 7/8" x 18g.flat  
Nyloc nut- 5/16" unc.  
Speed nut- 3/16" bsw.  
Screw- 3/16" x 1/2" mush/head  
Rivet- 73 AS 5-2  
A02012  
A02223  
A02002  
A02163  
A04060  
PAGE 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rover Mowers Limited  
GB Read the instructions carefully  
D
F
Lesen sie die hinweise sorgfaltig  
Lisenlesinstructionsattentivement  
SP Lea las instrucciones con mucho  
cuidado  
NL Lees de gebruiksaanwijzing  
zorgruldig  
I
Leggere attentamente le istruzioni  
GB Caution  
GB Rotating cutting blades  
D
F
Achtung  
Attention  
D
F
Rotierende messer  
Lames de coup rotatives  
SP Atencion  
SP Lame in movimento  
NL Draaiende Snijmessen  
NL Voorzichtig  
I
Attenzione!  
I
Lama con taglio a rotazione  
GB Keep bystanders away  
D
F
Andere fernhalten  
Restez a l'ecart du public  
SP Mantenga alos espectadores le jos de ustad  
NL Houd toeschouwer op afstand  
I
Tenere lontano le persone circostanti  
GB Stop the engine and disconnect the spark plug lead before checking,  
cleaning or working on the mower  
D
Den motor abstellen und das Zundkerzenkabel von der Zundkerze  
abziehen vor arbeiten am Maher  
F
Arretez le moteur et debranchez la bougie avant de verifer, nettoyer ou  
reparer la tondeuse  
SP Pare el motor y desconecte el cable de la bujf a antes de comprobar,  
limpiar o examinar la cortadora  
NL Stop de motor en trek de bougieleabel los voor het inspecteren,  
schoonmaken of reparen van de maaimachine  
I
Fermareilmotoreestaccareilcavettodallacandelaprimadicontrollare,  
pulire o aggiustare la tosaerba  
GB Powerstart  
Turn the key to the (I) position to engage the electric starter, release the  
key when the engine starts and allow to return to (O) position  
Powerstart Kontrollen  
D
F
Zundschlüssel auf Stelle an (I) drehen, um den Anlasser einzuschalten.  
Beim Anspringen des Motors den Schlück lassen  
Contrôles de démarrage électrique  
Tournez la clé sur la position (I) pour engager le démarrage électrique.  
Relâchez la clé quand le moteur démarre et laissez retourner à la  
position (O)  
SP Powerstart Control  
Mover la llave hacia (I) las posicion para atracer el arranque electrico.  
Dispara la llave cuando el motor empieza a dejar a regresar al (O)  
posicion apagdo  
NL Regulatuur bij Powerstart machines  
Draai de startsleutel in postie no. (I) em de electrische starter in te  
schaken. Laat de startsleutel los als de motor loopt en laat hem  
in de (O) teruggaan  
I
Controlli messa in moto  
Girare la chiave posizione (I) per accendere il motorino elettrico  
d'avviamento. Lasciare libera la chiave quando il motore e in moto, in  
modo che ritorni in posizione (O)  
PAGE 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RoverMowersLimited  
GB Self propelled drive control  
Moved towards (I) turns the clutch on and drives the mower forward.  
Moved towards (O) turns the clutch off and stops the mower  
driving  
D
F
Selbetantriebbetätgung  
Einstellung auf (I) aktiviert die Kupplung und den Motor vorwärs.  
Einstellung auf (I) schaltet die kupplung aus und bringt den Mäher zum  
Stehen  
Contrôle d'autotraction  
Déplacé vers (I) enclenche l'embrayage et fait avancer la tondeuse.  
Déplacévers(O)décengagel'embrayageelempéchelatondeused'avancer  
SP Autopropulsado marcas del control  
Movidohacia(I)mueveeldesembragadoryponeamarchaelcortacesped.  
Movido hacia el (O) apaga el desembragador y para el cortacesped  
NL Regulatuur bij relfverplaatsende machines  
Als men de knop op (I) zet, is de koppeling ingeschakeld en de machine  
rijdt vooruit. Alsdeknop(O)zet,schakeltmendeknoppelinguiten  
demachinestopt.  
I Camandotrazioneremovente  
SemossoversoI(innestato)innestalafrizioneemuoveinavantila  
faiciatricetosaerba.SemossoversoO(disinnestato)disinnestala  
frizioneefermalatrazionedellafalciatricetosaerba  
GB Operator presense control  
Handle moved towards the handle bars, engine and blades are free to  
rotate. Handle released, engine and blades stop rotating  
Bedieneranwesenheitakontrolle  
Giff in Richtung Giffbügel vorgestzt, motor und messer rotieren frei,  
Griff gelôst, Motor und messer stoppen  
Contrôle par opérateur  
D
F
Poigée avancée vers les mancherons, moteur et lames peuvent tourner.  
Poignée relâchée, moteur arrêtent de tourner  
SP Operador de las presencias controles  
Mango movido hacia manillas, motor y cuchillas estanlibres de hacer  
vucltas. Mango disparado, motor y cuchillas paran de hacer vucltas  
NL Dodenmanskoop regulatuurknop die aangeeft dat de oparateur  
aanwezig is  
De gasbedieningshendel geplaast in de richting van de hand grepen,  
de machine loopt en de messen draaien vrij. Gasbedieningshendel is  
afgezet, de machine stopt, en de messen draaicn neit meer  
I
Comando presenza operatore  
(I) Manopola mossa verso barre manubrio, motere e lame in posizione  
libers e rptanti. (O) manopola disimpegnata. Motre e lame fermi  
GB Throttle control  
Marked for off, slow and fast positions  
Gasbedienung  
D
F
Markierung aus, langsam sch schnell  
Contrôle des gaz  
Marque pour les positions arrêt, ralenti accéléré et  
SP Control del accelerador  
Marcado por apagado, despacio, rapido posiciones  
NL Gasknop regulatuur  
Voorzien van markteken uit, langzaam, snel tekening  
Comande  
I
Segno di poizione O staccato lento veloce  
PAGE11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
For your record:  
Para su referencia:  
Dealer .................................................  
Date of Purchase ....................................  
Model .................................................  
Serial No..............................................  
Vendedor .............................................  
Fecha de compra ....................................  
Modelo ................................................  
Serie no ...............................................  
Für lhre Aufzeichnung:  
Voor uw informatie:  
Händler ...............................................  
Lieferdatum ..........................................  
Modell Nr ............................................  
Seriennummer .......................................  
Handelaar.............................................  
Aankoopdatum.......................................  
Type ...................................................  
Serienummer.........................................  
Pour votre information personnelle:  
Dati da registrare:  
Fabricant..............................................  
Date d'achat..........................................  
Modèle ................................................  
NO de série ...........................................  
Distributore ..........................................  
Data d'acquito .......................................  
Modello ...............................................  
N.o Serie .............................................  
These machines are covered by one or more of the following Registered Designs and or Patents;  
Registered Designs: Australia. 131504, 134850  
Patents: Australia. 713852, 745750, New Zealand. 330293, US. 6085508, UK. GR2325139  
ACN 000 257 303  
Head Office and Factory: Rover Mowers Limited  
155 Fison Avenue West, Eagle Farm, 4009  
Brisbane, Queensland, Australia.  
Recycled paper  
GWAIL  
04003632- CE
Revision I.  
PRINTEDINAUSTRALIA
Copyright1/2003
©
Download from Www.Somanuals.com. All Manuals Search And Download.  

Billy Goat Lawn Mower FM3301 FM3301E User Manual
Bolens Lawn Mower 112 428R372 User Manual
Craftsman Lawn Mower 24728672 User Guide
Husqvarna Lawn Mower 532 43 38 61 User Guide
Poulan Lawn Mower 187301 User Guide
Snapper Lawn Aerator 2395 User Guide
Snapper Lawn Mower 1600 1650 1855 Series User Manual
Snapper Lawn Mower 1690079 User Manual
Snapper Lawn Mower Accessory Lawn Mower Accessory User Guide
Snapper Lawn Mower LT125G38AKV User Manual