Husqvarna Lawn Mower YTH26V54 User Guide
07002  
YTH26V54  
Owner's Manual  
Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine.  
The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty.  
532 44 11-32 Rev 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY RULES  
Safe Operation Practices for Ride-On Mowers  
III. CHILDREN  
Tragic accidents can occur if the operator is not alert to  
the presence of children. Children are often attracted to  
the machine and the mowing activity. Never assume that  
children will remain where you last saw them.  
GENERAL SERVICE  
•
Never operate machine in a closed area.  
Keep all nuts and bolts tight to be sure the equipment  
is in safe working condition.  
•
•
•
•
•
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
•
•
Never tamper with safety devices. Check their proper  
operation regularly.  
Keep machine free of grass, leaves, or other debris  
build-up. Cleanoilorfuelspillageandremoveanyfuel-  
soaked debris. Allow machine to cool before storing.  
If you strike a foreign object, stop and inspect the  
machine. Repair, if necessary, before restarting.  
Nevermakeanyadjustmentsorrepairswiththeengine  
running.  
Check grass catcher components and the discharge  
chute frequently and replace with manufacturer's rec-  
ommended parts, when necessary.  
Before and while backing, look behind and down for  
small children.  
•
•
•
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Never allow children to operate the machine.  
Useextracarewhenapproachingblindcorners,shrubs,  
trees, or other objects that may block your view of a  
child.  
•
•
•
•
•
Mower blades are sharp. Wrap the blade or wear  
gloves, and use extra caution when servicing them.  
Check brake operation frequently. Adjust and service  
as required.  
Maintain or replace safety and instruction labels, as  
necessary.  
IV. TOWING  
•
Tow only with a machine that has a hitch designed for  
towing. Do not attach towed equipment except at the  
hitch point.  
•
•
•
•
Follow the manufacturer's recommendation for weight  
limits for towed equipment and towing on slopes.  
Never allow children or others in or on towed  
equipment.  
On slopes, the weight of the towed equipment may  
cause loss of traction and loss of control.  
Travel slowly and allow extra distance to stop.  
•
Be sure the area is clear of bystanders before operat-  
ing. Stop machine if anyone enters the area.  
Never carry passengers.  
•
•
Do not mow in reverse unless absolutely necessary.  
Always look down and behind before and while back-  
ing.  
Nevercarrychildren,evenwiththebladesshutoff. They  
may fall off and be seriously injured or interfere with  
safemachineoperation.Childrenwhohavebeengiven  
rides in the past may suddenly appear in the mowing  
area for another ride and be run over or backed over  
by the machine.  
Keepchildrenoutofthemowingareaandinthewatchful  
care of a responsible adult other than the operator.  
Be alert and turn machine off if a child enters the  
area.  
Before and while backing, look behind and down for  
small children.  
Mow up and down slopes (15° Max), not across.  
Choose a low ground speed so that you will not have  
to stop or shift while on the slope.  
Avoid starting, stopping, or turning on a slope. If the  
tires lose traction, disengage the blades and proceed  
slowly straight down the slope.  
V. SERVICE  
SAFE HANDLING OF GASOLINE  
To avoid personal injury or property damage, use extreme  
careinhandlinggasoline. Gasolineisextremelyflammable  
and the vapors are explosive.  
•
•
Extinguish all cigarettes, cigars, pipes, and other  
sources of ignition.  
Use only approved gasoline container.  
Never remove gas cap or add fuel with the engine  
running. Allow engine to cool before refueling.  
Never fuel the machine indoors.  
Never store the machine or fuel container where there  
is an open flame, spark, or pilot light such as on a water  
heater or other appliances.  
Never fill containers inside a vehicle or on a truck or  
trailer bed with plastic liner. Always place containers  
on the ground away from your vehicle when filling.  
Remove gas-powered equipment from the truck or  
trailer and refuel it on the ground. If this is not possible,  
then refuel such equipment with a portable container,  
rather than from a gasoline dispenser nozzle.  
Keepthenozzleincontactwiththerimofthefueltankor  
container opening at all times until fueling is complete.  
Do not use a nozzle lock-open device.  
If fuel is spilled on clothing, change clothing immedi-  
ately.  
Never overfill fuel tank. Replace gas cap and tighten  
securely.  
•
•
•
•
•
•
•
•
•
•
•
•
•
•
If machine stops while going uphill, disengage blades,  
shift into reverse and back down slowly.  
Do not turn on slopes unless necessary, and then, turn  
slowly and gradually downhill, if possible.  
•
•
•
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONGRATULATIONS on your purchase of a new tractor.  
Ithasbeendesigned,engineeredandmanufacturedtogive  
you the best possible dependability and performance.  
PRODUCT SPECIFICATIONS  
Gasoline Capacity  
and type:  
3.0 Gallons  
Unleaded Regular  
Shouldyouexperienceanyproblemyoucannoteasilyrem-  
edy, please contact your nearest authorized servicecenter/  
department We have competent, well-trained technicians  
and the proper tools to service or repair this tractor.  
Oil Type (API-SG-SL):  
SAE 30 (above 32°F)  
SAE 5W-30 (below 32°F)  
Oil Capacity:  
W/ Filter:  
W/O Filter:  
64 oz  
60 oz  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your tractor properly.  
Always observe the “SAFETY RULES”.  
Spark Plug:  
Champion QC12YC  
(Gap: .040")  
Ground Speed (MPH):  
Forward:  
Reverse:  
0 - 5.5  
0 - 2.4  
CUSTOMER RESPONSIBILITIES  
Charging System:  
Battery:  
16 AMPS @ 3600 RPM  
•
•
Read and observe the safety rules.  
Follow a regular schedule in maintaining, caring for  
and using your tractor.  
AMP/HR:  
MIN. CCA:  
Case Size:  
28  
230  
U1R  
•
Follow the instructions under “Maintenance” and “Stor-  
age” sections of this owner’s manual.  
Blade Bolt Torque:  
45-55 FT. LBS.  
WARNING: This tractor is equipped with an internal com-  
bustion engine and should not be used on or near any un-  
improved forest-covered, brush-covered or grass-covered  
land unless the engine’s exhaust system is equipped with  
a spark arrester meeting applicable local or state laws (if  
any). If a spark arrester is used, it should be maintained  
in effective working order by the operator.  
In the state of California the above is required by law  
(Section 4442 of the California Public Resources Code).  
Other states may have similar laws. Federal laws apply  
on federal lands.  
A spark arrester for the muffler is available through your  
nearest authorized service center/department.  
TABLE OF CONTENTS  
SAFETY RULES .........................................................2-3  
PRODUCT SPECIFICATIONS....................................... 4  
CUSTOMER RESPONSIBILITIES................................. 4  
UNASSEMBLED PARTS............................................... 5  
ASSEMBLY.................................................................6-9  
OPERATION ...........................................................10-16  
MAINTENANCE SCHEDULE ...................................... 17  
MAINTENANCE..................................................... 17-20  
SERVICE AND ADJUSTMENTS............................21-25  
STORAGE.................................................................... 26  
TROUBLESHOOTING............................................27-28  
REPAIR PARTS ......................................................29-44  
WARRANTY............................................................45-48  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
UNASSEMBLED PARTS  
Mower Front Wheel  
(1) Shoulder Bolt  
(1) 1-1/4  
O.D. Washer  
(1) 3/8-16  
Locknut  
(1) Wheel  
Mower  
If Equipped  
(5) 1-3/16  
O.D. Washers  
(2) Rear  
Lift Link  
(1) 3/4 O.D.  
Washers  
Assemblies  
(1) Small  
Retainer Springs  
(1) Front  
Lift Link  
(1) Small  
Retainer  
Springs  
(5) Large  
Retainer Springs  
(1) Anti-  
Sway Bar  
Assembly  
Keys  
Slope Sheet  
(1) Oil Drain Tube  
For Future Use  
(2) Keys  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.  
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use  
the correct tools as necessary to ensure proper tightness.  
TOOLS REQUIRED FOR ASSEMBLY  
A socket wrench set will make assembly easier. Standard  
wrench sizes are listed.  
A
(2) 7/16" wrenches  
(1) 1/2" wrench  
Utility knife  
Tire pressure gauge  
Pliers  
(1) 3/4" wrench  
(1) 3/4" socket w/drive ratchet  
(1) 9/16" wrench  
Flashlight  
Whenrightorlefthandismentionedinthismanual,itmeans  
when you are in the operating position (seated behind the  
steering wheel).  
Fig. 2  
NOTE:Youmaynowrollyourtractorofftheskid. Followthe  
instructions below to remove the tractor from the skid.  
TOREMOVETRACTORFROMCARTON  
WARNING:Beforestarting,read,understandandfollow  
all instructions in the Operation section of this manual. Be  
sure tractor is in a well-ventilated area. Be sure the area in  
front of tractor is clear of other people and objects.  
UNPACK CARTON  
•
Remove all accessible loose parts and parts cartons  
from carton .  
•
•
Cut along dotted lines on all four panels of carton.  
Remove end panels and lay side panels flat.  
Check for any additional loose parts or cartons and  
remove.  
TOROLLTRACTOROFFSKID (SeeOperation  
section for location and function of controls)  
•
•
•
Raise attachment lift lever to its highest position.  
Releaseparkingbrakebydepressingclutch/brakepedal.  
Place freewheel control in "transmission disengaged"  
position (See “TO TRANSPORT” in the Operation  
section of this manual).  
BEFORE REMOVING TRACTOR FROM  
SKID  
TO CHECK BATTERY (See Fig. 1)  
•
Lift hood to raised position.  
•
•
Roll tractor forward off skid.  
Removebandingholdingthedeflectorshieldupagainst  
tractor.  
NOTE: If this battery is put into service after month and  
year indicated on label (label is located between terminals)  
charge battery for minimum of one hour at 6-10 amps.  
(See "BATTERY" in Maintenance section of this manual  
for charging instructions).  
Continue with the instructions that follow.  
TO INSTALL MOWER AND DRIVE BELT  
(See Figs. 3 - 15)  
1. SET PARKING BRAKE LEVER AND LOWER AT-  
•
For battery and battery cable installation see "RE-  
PLACINGBATTERY"inthe"ServiceandAdjustments"  
section in this manual.  
TACHMENT LIFT LEVER (See Fig. 2 and 3)  
•
•
Depress clutch/brake pedal all the way down and hold.  
Pull parking brake lever up and hold, release pressure  
from clutch/brake pedal, then release parking brake  
lever. Pedal should remain in brake position. Ensure  
parking brake will hold tractor secure.  
LABEL  
PARKING  
BRAKE  
LEVER  
Fig. 1  
Fig. 3  
ADJUST SEAT (See Fig. 2)  
•
•
Sit in seat.  
CAUTION: Lift lever is spring loaded. Have a  
tight grip on lift lever, lower it slowly and en-  
gage in lowest position. Lift lever is located  
on left side of fender.  
Lift up adjustment lever (A) and slide seat until a com-  
fortable position is reached which allows you to press  
clutch/brake pedal all the way down.  
•
Release lever to lock seat in position.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
4. SLIDE MOWER UNDER TRACTOR (See Fig. 8)  
•
Bring belt forward and check belt for proper routing in  
all mower pulley grooves.  
LIFT  
LEVER  
NOTE: Be sure mower side suspension arms (A) are point-  
ing forward before sliding mower under tractor.  
•
Slide mower under tractor until it is centered under  
tractor.  
Fig. 4  
2. ASSEMBLEFRONTGAUGEWHEEL(W)TOFRONT  
OF MOWER (See Fig. 5)  
Q
H. FRONT MOWER  
W
H
BRACKET  
W. FRONT GAUGE  
WHEEL  
X. SHOULDER  
BOLT  
X
Y. 1-1/4 O.D.  
A. MOWER SIDE  
WASHER  
Y
A
Z
SUSPENSION  
Z. 3/8-16 LOCKNUT  
ARMS  
Fig. 5  
Q. DEFLECTOR  
02965  
SHIELD  
3. TURN STEERING WHEEL LEFT AND POSITION  
MOWER (See Fig. 6)  
Fig. 8  
•
Turn steering wheel to the left as far as it will go and  
position mower on right side of tractor with deflector  
shield (Q) to the right.  
5. INSTALL ANTI-SWAY BAR (S) (IF EQUIPPED)  
(See Fig. 9 - 11)  
FRONT  
ANTI-SWAY BAR (S)  
TOWARDS  
Q
TOWARDS  
MOWER DECK  
TRANSAXLE  
ENGINE  
90° END  
INTEGRATED WASHER END  
TRANSAXLE  
Fig. 9  
•
Fromrightsideofmower,firstinsert90°endofanti-sway  
bar (S) into hole in transaxle bracket (T), located near  
left rear tire in front of transaxle.  
Q. DEFLECTOR  
02965  
SHIELD  
BACK  
NOTE: Flashlight may be helpful.  
Fig. 6  
F
M
A. MOWER SIDE SUSPENSION  
B
ARMS  
B. RETAINER SPRING  
C. REAR LIFT LINK(S)  
W
L
A
D. RIGHT SIDE REAR MOWER  
BRACKET  
K
E
E. FRONT LIFT LINK ASSEMBLY  
F. FRONT SUSPENSION BRACKET  
H. FRONT MOWER BRACKET  
I. LEFT SIDE REAR MOWER  
BRACKET  
H
K. BELT TENSION ROD  
L. LOCKING BRACKET  
M. ENGINE CLUTCH PULLEY  
Q. DEFLECTOR SHIELD  
S. ANTI-SWAY BAR  
C
I
C
S
D
W. FRONT GAUGE WHEEL  
Q
Fig. 7  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
7. ATTACH REAR LIFT LINKS (C) (See Fig. 13)  
ANTI-SWAY BAR  
(S) LOCATION  
•
•
Insert rod end of rear lift link (C) into hole (U) in tractor  
TRANSAXLE  
BRACKET (T)  
LOCATED  
BETWEEN REAR  
TIRES  
lift shaft suspension arm and pivot link down to mower.  
Lift rear corner of mower and position slot in link as-  
sembly over pin on rear mower bracket (D) and secure  
with large washer and large retainer spring.  
•
Repeat on opposite side of tractor.  
U
C
S
C. REAR LIFT LINK(S)  
D. RIGHT SIDE REAR  
MOWER BRACKET  
D
U. HOLE  
T
S. ANTI-SWAY BAR  
T. TRANSAXLE BRACKET  
Fig. 13  
Fig. 10  
8 ATTACH FRONT LINK (E) (See Fig. 14)  
NOTE: Depending on model, bracket (T) may be differ-  
ent than shown but hole for anti-sway bar will be in same  
position/location.  
•
•
Turn steering wheel to position wheels straight forward.  
From front of tractor, insert rod end of front link (E)  
throughfrontholeintractorfrontsuspensionbracket(F).  
•
Pivot the integrated washer end of anti-sway bar (S)  
towards mower deck bracket on right side of mower.  
Insert integrated washer end of bar into hole in rear  
mower bracket (D). Move mower as needed to insert  
integratedwasherendofbarintorearmowerbracket(D).  
•
•
Move to left side of mower and and insert large retainer  
spring (G) through hole in front link (E) behind front  
suspension bracket (F).  
Insert other end of link (E) into hole in front mower  
bracket (H) and secure with washer and small retainer  
spring (J).  
•
Secure with small washer and small retainer spring as  
shown.  
NOTE: Requires deck lifting.  
FRONT LINK  
LOCATION  
D. RIGHT SIDE  
REAR MOWER  
BRACKET  
S
T
S. ANTI-SWAY BAR  
T. TRANSAXLE  
BRACKET  
D
M
Fig. 11  
6. ATTACH MOWER SIDE SUSPENSION ARMS (A) TO  
CHASSIS (See Fig. 12)  
H
F
•
Position front hole in side suspension arm (A) over  
pin on outside of tractor chassis and secure with large  
washer and large retainer spring (B).  
G
E
J
•
Repeat on opposite side of tractor.  
A.MOWER SIDE  
SUSPENSION  
ARMS  
E. FRONT LIFT LINK ASSEMBLY  
F. FRONT SUSPENSION BRACKET  
G. LARGE RETAINER SPRING  
H. FRONT MOWER BRACKET  
J. SMALL RETAINER SPRING  
M. ENGINE CLUTCH PULLEY  
B.RETAINER  
SPRING  
D.RIGHT  
SIDE REAR  
MOWER  
D
B
A
BRACKET  
Fig. 14  
Fig. 12  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
9 INSTALL BELT ON ENGINE CLUTCH PULLEY (M)  
✓CHECKLIST  
(See Fig. 7 & 15)  
BEFORE YOU OPERATE YOUR NEW TRACTOR, WE  
WISH TO ASSURE THAT YOU RECEIVE THE BEST  
PERFORMANCE AND SATISFACTION FROM THIS  
QUALITY PRODUCT.  
•
•
Disengage belt tension rod (K) from locking bracket (L).  
Install belt onto engine clutch pulley (M).  
M
PLEASE REVIEW THE FOLLOWING CHECKLIST:  
✓
All assembly instructions have been completed.  
✓
✓
✓
✓
No remaining loose parts in carton.  
Battery is properly prepared and charged.  
Seat is adjusted comfortably and tightened securely.  
All tires are properly inflated. (For shipping purposes,  
the tires were overinflated at the factory).  
M.ENGINE  
CLUTCH PULLEY  
✓
Be sure mower deck is properly leveled side-to-side/  
front-to-rear for best cutting results. (Tires must be  
properly inflated for leveling).  
Fig. 15  
✓
✓
✓
Check mower and drive belts. Be sure they are routed  
IMPORTANT: Check belt for proper routing in all mower  
properly around pulleys and inside all belt keepers.  
pulley grooves and under mandrel covers.  
Check wiring. See that all connections are still secure  
and wires are properly clamped.  
Before driving tractor, be sure freewheel control is in  
“transmission engaged” position (see “TO TRANS-  
PORT” in the Operation section of this manual).  
•
Engage belt tension rod (K) on locking bracket (L).  
CAUTION: Belt tension rod is spring loaded.  
Have a tight grip on rod and engage slowly.  
WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY  
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT  
ITEMS:  
•
•
Raise attachment lift lever to highest position.  
If necessary, adjust gauge wheels before operating  
mowerasshownintheOperationsectionofthismanual.  
✓
Engine oil is at proper level.  
MOWER DRIVE BELT INSTALLATION  
✓
Fuel tank is filled with fresh, clean, regular unleaded  
gasoline.  
Follow procedure described in “TO REPLACE MOWER  
BLADE DRIVE BELT ” in the "Service and Adjustments"  
section of this manual.  
✓
Become familiar with all controls, their location and  
function. Operate them before you start the engine.  
Be sure brake system is in safe operating condition.  
Be sure Operator Presence System and Reverse  
OperationSystem(ROS)areworkingproperly(Seethe  
Operation and Maintenance sections in this manual).  
It is important to purge the transmission before  
operating your tractor for the first time. Follow proper  
startingandtransmissionpurginginstructions(See“TO  
START ENGINE” and “PURGE TRANSMISSION” in  
the Operation section of this manual).  
✓
✓
CHECK TIRE PRESSURE  
The tires on your tractor were overinflated at the factory  
for shipping purposes. Correct tire pressure is important  
for best cutting performance.  
✓
•
Reduce tire pressure to PSI shown on tires.  
CHECK DECK LEVELNESS  
For best cutting results, mower housing should be prop-  
erly leveled. See “TO LEVEL MOWER HOUSING” in the  
Service and Adjustments section of this manual.  
CHECK FOR PROPER POSITION OF ALL  
BELTS  
See the figures that are shown for replacing motion and  
mower blade drive belts in the Service and Adjustments  
section of this manual. Verify that the belts are routed  
correctly.  
CHECK BRAKE SYSTEM  
Afteryoulearnhowtooperateyourtractor,checktoseethat  
the brake is operating properly. See “TO CHECK BRAKE”  
in the Service and Adjustments section of this manual.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning.  
FAST  
SLOW  
REVERSE  
HIGH  
LOW  
NEUTRAL  
CHOKE  
IGNITION SWITCH  
MOWER LIFT  
ENGINE START  
MOWER HEIGHT  
ENGINE ON  
PARKING BRAKE  
REVERSE  
OPERATION  
SYSTEM (ROS)  
ENGINE OFF  
CLUTCH/BRAKE  
PEDAL  
LIGHTS ON  
CRUISE CONTROL  
BATTERY  
REVERSE  
FUEL  
FORWARD  
15  
15  
ATTACHMENT  
CLUTCH ENGAGED  
DANGER, KEEP HANDS  
AND FEET AWAY  
ATTACHMENT  
CLUTCH DISENGAGED  
SLOPE HAZARDS  
KEEP AREA CLEAR  
(SEE SAFETY RULES SECTION)  
DANGER indicates a hazard which, if not avoided,  
will result in death or serious injury.  
WARNING indicates a hazard which, if not avoided,  
could result in death or serious injury.  
FREE WHEEL  
(Automatic Models only)  
CAUTION indicates a hazard which, if not avoided,  
might result in minor or moderate injury.  
CAUTION when used without the alert symbol,  
indicates a situation that could result in damage  
to the tractor and/or engine.  
Failure to follow instructions  
could result in serious injury or  
death. The safety alert symbol  
is used to identify safety inform-  
ation about hazards which can  
result in death, serious injury  
and/or property damage.  
HOT SURFACES indicates a hazard which,  
if not avoided, could result in death, serious injury  
and/or property damage.  
FIRE indicates a hazard which, if not avoided,  
could result in death, serious injury and/or  
property damage.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOW YOUR TRACTOR  
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR  
Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and adjustments.  
Save this manual for future reference.  
G
P
D
H
E
F
B
A
M
C
K
J
L
Fig. 16  
Our tractors conform to the applicable safety standards of the American National Standards Institute.  
(A) ATTACHMENT LIFT LEVER - Used to raise and lower  
(H) LIGHT SWITCH - Turns the headlights on and off.  
the mower or other attachments mounted to your tractor.  
(J) CRUISE CONTROL LEVER - Used to set forward  
movement of tractor at desired speed without holding the  
forward drive pedal.  
(B) BRAKE PEDAL - Used for braking the tractor and  
starting the engine.  
(C) PARKING BRAKE - Locks clutch/brake pedal into  
the brake position.  
(K) FORWARD DRIVE PEDAL - Used for forward move-  
ment of tractor.  
(D) THROTTLE/CHOKE CONTROL - Used for starting  
and controlling engine speed.  
(L) REVERSE DRIVE PEDAL - Used for reverse move-  
ment of tractor.  
(E) ATTACHMENTCLUTCHSWITCH-Usedtoengagethe  
mowerbladesorotherattachmentsmountedtoyourtractor.  
(M) FREEWHEEL CONTROL - Disengages transmission  
for pushing or slowly towing the tractor with the engine off.  
(F) IGNITION SWITCH - Used for starting and stopping  
the engine.  
(P) SERVICE REMINDER / HOUR METER - Indicates  
when service is required for the engine and mower.  
(G) REVERSE OPERATION SYSTEM (ROS) "ON"  
POSITION - Allows operation of mower or other powered  
attachment while in reverse.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any tractor can result in foreign objects thrown into the eyes, which can result  
in severe eye damage. Always wear safety glasses or eye shields while operating your tractor  
or performing any adjustments or repairs. We recommend standard safety glasses or a wide  
vision safety mask worn over spectacles.  
NOTE:Failuretomovethrottlecontrolbetweenhalfandfull  
HOW TO USE YOUR TRACTOR  
speed (fast) position, before stopping may cause engine  
to “backfire”.  
TO SET PARKING BRAKE(See Fig. 17)  
•
Turnignitionkey(F)to“STOP”positionandremovekey.  
Always remove key when leaving tractor to prevent  
unauthorized use.  
Your tractor is equipped with an operator presence sens-  
ing switch. When engine is running, any attempt by the  
operator to leave the seat without first setting the parking  
brake will shut off the engine.  
•
Never use the choke to stop the engine.  
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY  
POSITION OTHER THAN "STOP" WILL CAUSE THE BATTERY  
TO BE DISCHARGED, (DEAD).  
•
•
Depress brake pedal (B) all the way down and hold.  
Pull parking brake lever (C) up and hold, release pres-  
sure from brake pedal (B), then release parking brake  
lever. Pedal should remain in brake position. Make  
sure parking brake will hold tractor secure.  
NOTE: Under certain conditions when tractor is standing  
idlewiththeenginerunning, hotengineexhaustgasesmay  
cause “browning” of grass. To eliminate this possibility, al-  
ways stop engine when stopping tractor on grass areas.  
C
CAUTION: Always stop tractor com-  
pletely, as described above, and set  
parkingbrakebeforeleavingtheopera-  
tor's position.  
B
TOUSETHROTTLECONTROL(D)(SeeFig.19)  
Always operate engine at full speed (fast).  
Fig. 17  
•
Operating engine at less than full speed (fast) reduces  
the engine's operating efficiency.  
STOPPING (See Fig. 18)  
MOWER BLADES -  
•
Full speed (fast) offers the best mower performance.  
•
To stop mower blades, place attachment clutch control  
in the “DISENGAGED” position ( ).  
D
F
(
) ATTACHMENT  
CLUTCH SWITCH  
“DISENGAGED”  
(
) ATTACHMENT  
CLUTCH SWITCH  
“ENGAGED”  
Fig. 19  
Fig. 18  
GROUND DRIVE -  
•
To stop ground drive, depress brake pedal into full  
“BRAKE” position.  
IMPORTANT: FORWARD AND REVERSE DRIVE PEDALS  
RETURN TO NEUTRAL POSITION WHEN NOT DEPRESSED.  
ENGINE -  
•
Move throttle control (D) between half and full speed  
(fast) position.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
•
Put attachment lift lever in desired cutting height slot.  
TO MOVE FORWARD AND BACKWARD  
(See Fig. 20)  
The direction and speed of movement is controlled by the  
forward and reverse drive pedals.  
The cutting height range is approximately 1" to 4". The  
heights are measured from the ground to the blade tip with  
theenginenotrunning.Theseheightsareapproximateand  
may vary depending upon soil conditions, height of grass  
and types of grass being mowed.  
•
•
Start tractor and release parking brake.  
Slowlydepressforward(K)orreverse(L)drivepedalto  
begin movement. Ground speed increases the further  
down the pedal is depressed.  
•
The average lawn should be cut to approximately  
2-1/2" during the cool season and to over 3" during hot  
months. For healthier and better looking lawns, mow  
often and after moderate growth.  
•
For best cutting performance, grass over 6" in height  
should be mowed twice. Make the first cut relatively  
high; the second to desired height.  
K
TO ADJUST GAUGE WHEELS (See Fig. 22)  
J
Gaugewheels areproperlyadjustedwhentheyareslightly  
off the ground when mower is at the desired cutting height  
in operating position. Gauge wheels then keep the deck  
in proper position to help prevent scalping in most terrain  
conditions.  
L
Fig. 20  
NOTE: Adjust gauge wheels with tractor on a flat level  
surface.  
TO USE CRUISE CONTROL (J) (See Fig. 20)  
The cruise control feature can be used for forward travel  
•
Adjust mower to desired cutting height (See “TO AD-  
JUST MOWER CUTTING HEIGHT” in this section of  
manual).  
only.  
•
With mower in desired height of cut position, gauge  
wheels should be assembled so they are slightly off  
the ground. Install gauge wheel in appropriate hole.  
Tighten securely.  
Repeat for all, installing gauge wheel in same adjust-  
ment hole.  
SYSTEM CHARACTERISTICS  
The cruise control should only be used while mowing or  
transporting on relatively smooth, straight surfaces. Other  
conditions such as trimming at slow speeds may cause the  
cruise control to disengage. Do not use the cruise control  
on slopes, rough terrian or while trimmimg or turning.  
•
•
With forward drive pedal depressed to desired speed,  
pull cruise control lever (J) up and hold while lifting  
your foot off the pedal, then release the lever.  
To disengage the cruise control, depress the brake pedal  
or tap on forward drive pedal.  
TO ADJUST MOWER CUTTING HEIGHT  
(See Fig. 21)  
The position of the attachment lift lever (A) determines the  
cutting height.  
Fig. 22  
TO OPERATE MOWER  
Your tractor isequipped withan operator presencesensing  
switch. Any attempt by the operator to leave the seat with  
the engine running and the attachment clutch engaged will  
shut off the engine. You must remain fully and centrally  
positioned in the seat to prevent the engine from hesitat-  
ing or cutting off when operating your equipment on rough,  
rolling terrain or hills.  
A
•
Selectdesiredheightofcut(see"TOADJUSTMOWER  
CUTTING HEIGHT")  
•
Start mower blades by engaging attachment clutch  
control.  
Fig. 21  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO STOP MOWER BLADES  
TO OPERATE ON HILLS  
•
Disengage attachment clutch control.  
CAUTION: Do not drive up or down  
hills with slopes greater than 15° and  
do not drive across any slope.  
CAUTION: Do not operate the mower  
without either the entire grass catcher, on  
mowerssoequipped,orthedeflectorshield  
(S) in place (See Fig. 23).  
•
Choose the slowest speed before starting up or down  
hills.  
•
•
Avoid stopping or changing speed on hills.  
If stopping is absolutely necessary, push brake pedal  
quickly to brake position and engage parking brake.  
S
•
Torestartmovement, slowlyreleaseparkingbrakeand  
brake pedal.  
•
•
Slowlydepressappropriatedrivepedaltoslowestsetting.  
Make all turns slowly.  
TO TRANSPORT (See Figs. 16 and 24)  
When pushing or towing your tractor, be sure to disengage  
transmissionbyplacingfreewheelcontrolinfreewheeling po-  
sition.Freewheelcontrolislocatedatthereardrawbaroftractor.  
Fig. 23  
•
Raiseattachmentlifttohighestpositionwithattachment  
lift control.  
REVERSE OPERATION SYSTEM (ROS)  
Your tractor is equipped with a Reverse Operation System  
(ROS). Any attempt by the operator to travel in the reverse  
directionwiththeattachmentclutchengagedwillshutoffthe  
engineunlessignitionkeyisplacedintheROS"ON"position.  
•
Pull freewheel control out and down into the slot and  
release so it is held in the disengaged position.  
Do not push or tow tractor at more than two (2) MPH.  
To reengage transmission, reverse above procedure.  
•
•
WARNING: Backing up with the attachment clutch en-  
gaged while mowing is strongly discouraged. Turning the  
ROS "ON", to allow reverse operation with the attachment  
clutch engaged, should only be done when the operator  
decides it is necessary to reposition the machine with the  
attachment engaged. Do not mow in reverse unless  
absolutely necessary.  
NOTE: To protect hood from damage when transporting  
your tractor on a truck or a trailer, be sure hood is closed  
and secured to tractor. Use an appropriate means of tying  
hood to tractor (rope, cord, etc.).  
TRANSMISSION ENGAGED  
ROS "ON"  
POSITION  
ENGINE "ON" POSITION  
(NORMAL OPERATING)  
TRANSMISSION DISENGAGED  
USING THE REVERSE OPERATION SYSTEM -  
Only use if you are certain no children or other bystanders  
will enter the mowing area.  
Fig. 24  
TOWING CARTS AND OTHER ATTACHMENTS  
Tow only the attachments that are recommended by and  
complywithspecificationsofthemanufacturerofyourtrac-  
tor. Use common sense when towing. Too heavy of a load,  
while on a slope, is dangerous. Tires can lose traction with  
the ground and cause you to lose control of your tractor.  
•
•
Depress brake pedal all the way down.  
Withenginerunning,turnignitionkeycounterclockwise  
to ROS "ON" position.  
•
•
•
Look down and behind before and while backing.  
Slowly depress reverse drive pedal to start movement.  
When use of the ROS is no longer needed, turn the  
ignition key clockwise to engine "ON" position.  
SERVICE REMINDER/HOUR METER  
Serviceremindershowsthetotalnumberofhourstheengine  
has run and flashes to indicate that the engine or mower  
needs servicing. When service is required, the service  
reminder will flash for two hours. To service engine and  
mower, see the Maintenance section of this manual.  
NOTE: Service reminder runs when the ignition key is in  
any position but "STOP". For accurate reading, be sure key  
remainsinthe"STOP"positionwhenengineisnotrunning.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
TO START ENGINE (See Fig. 16)  
When starting the engine for the first time or if the engine  
has run out of fuel, it will take extra cranking time to move  
fuel from the tank to the engine.  
BEFORE STARTING THE ENGINE  
CHECK ENGINE OIL LEVEL  
The engine in your tractor has been shipped, from the  
factory, already filled with summer weight oil.  
•
Besurefreewheelcontrolisinthetransmissionengaged  
position.  
•
•
Check engine oil with tractor on level ground.  
•
Sit on seat in operating position, depress brake pedal  
and set parking brake.  
Remove oil fill cap/dipstick and wipe clean, reinsert the  
dipstick and screw cap tight, wait for a few seconds,  
remove and read oil level. If necessary, add oil until  
“FULL” mark on dipstick is reached. Do not overfill.  
•
•
Move attachment clutch to “DISENGAGED” position.  
Move throttle control to choke position.  
•
•
For cold weather operation you should change oil for  
easier starting (See “OIL VISCOSITY CHART” in the  
Maintenance section of this manual).  
To change engine oil, see the Maintenance section in  
this manual.  
NOTE: Before starting, read the warm and cold starting  
procedures below.  
•
Insertkeyintoignitionandturnkeyclockwiseto“START”  
position and release key as soon as engine starts.  
Do not run starter continuously for more than fifteen  
seconds per minute. If the engine does not start after  
several attempts, move throttle control to fast position,  
wait a few minutes and try again. If engine still does  
not start, move the throttle control back to the choke  
position and retry.  
ADD GASOLINE  
•
Fill fuel tank to bottom of filler neck. Do not overfill.  
Use fresh, clean, regular unleaded gasoline with a  
minimum of 87 octane. (Use of leaded gasoline will  
increase carbon and lead oxide deposits and reduce  
valve life). Do not mix oil with gasoline. Purchase fuel  
in quantities that can be used within 30 days to assure  
fuel freshness.  
WARM WEATHER STARTING (50°F/10°C and above)  
•
When engine starts, move the throttle control to the  
fast position.  
•
The attachments and ground drive can now be used. If  
the engine does not accept the load, restart the engine  
and allow it to warm up for one minute using the choke  
as described above.  
CAUTION: Wipe off any spilled oil or  
fuel. Do not store, spill or use gasoline  
near an open flame.  
COLD WEATHER STARTING (50°F/10°C and below)  
IMPORTANT: WHEN OPERATING IN TEMPERATURES  
BELOW32°F(0°C),USEFRESH,CLEANWINTERGRADE  
GASOLINE TO HELP ENSURE GOOD COLD WEATHER  
STARTING.  
•
When engine starts, allow engine to run with the  
throttle control in the choke position until the engine  
runs roughly, then move throttle control to fast posi-  
tion. This may require an engine warm-up period from  
several seconds to several minutes, depending on the  
temperature.  
CAUTION: Alcohol blended fuels (called gasohol  
or using ethanol or methanol) can attract moisture  
which leads to separation and formation of acids  
during storage. Acidic gas can damage the fuel  
system of an engine while in storage. To avoid  
engineproblems,thefuelsystemshouldbeemptied  
before storage of 30 days or longer. Drain the gas  
tank, start the engine and let it run until the fuel  
lines and carburetor are empty. Use fresh fuel next  
season. See Storage Instructions for additional  
information. Neveruseengineorcarburetorcleaner  
products in the fuel tank or permanent damage  
may occur.  
AUTOMATIC TRANSMISSION WARM UP  
•
Beforedrivingtheunitincoldweather,thetransmission  
should be warmed up as follows:  
•
•
Be sure the tractor is on level ground.  
Release the parking brake and let the brake slowly  
return to operating position.  
•
Allowoneminutefortransmissiontowarmup.This  
can be done during the engine warm up period.  
•
The attachments can also be used during the engine  
warm-upperiodafterthetransmissionhasbeenwarmed  
up.  
NOTE: If at a high altitude (above 3000 feet) or in cold  
temperatures (below 32°F/0°C) the carburetor fuel mixture  
may need to be adjusted for best engine performance. See  
“TO ADJUST CARBURETOR” in the Service and Adjust-  
ments section of this manual.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
PURGE TRANSMISSION  
MOWING TIPS  
•
•
Tire chains cannot be used when the mower housing  
is attached to tractor.  
CAUTION: Never engage or disengage  
freewheelleverwhiletheengineisrunning.  
Mower should be properly leveled for best mowing  
performance. See “TO LEVEL MOWER HOUSING”  
in the Service and Adjustments section of this manual.  
To ensure proper operation and performance, it is recom-  
mended that the transmission be purged before operating  
tractor for the first time. This procedure will remove any  
trapped air inside the transmission which may have devel-  
oped during shipping of your tractor.  
IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE  
REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD  
BEPURGEDAFTERREINSTALLATIONBEFOREOPERATING  
THE TRACTOR.  
•
•
Thelefthandsideofmowershouldbeusedfortrimming.  
Drive so that clippings are discharged onto the area  
that has been cut. Have the cut area to the right of  
the tractor. This will result in a more even distribution  
of clippings and more uniform cutting.  
•
When mowing large areas, start by turning to the right  
so that clippings will discharge away from shrubs,  
fences, driveways, etc. After one or two rounds, mow  
in the opposite direction making left hand turns until  
finished (See Fig. 25).  
1. Place tractor safely on a level surface - that is clear  
and open - with engine off and parking brake set.  
2. Disengage transmission by placing freewheel control  
in disengaged position (See “TO TRANSPORT” in this  
section of manual).  
3. Sitting in the tractor seat, start engine. After the en-  
gine is running, move throttle control to slow position.  
Disengage parking brake  
CAUTION: Atanytime,duringstep4,there  
may be movement of the drive wheels.  
4. Depress forward drive pedal to full forward position,  
hold for five (5) seconds and release pedal. Depress  
reverse drive pedal to full reverse position, hold for five  
(5) seconds and release pedal. Repeat this procedure  
three (3) times.  
Fig. 25  
5. Shut- off engine and set parking brake.  
•
If grass is extremely tall, it should be mowed twice to  
reduce load and possible fire hazard from dried clip-  
pings. Make first cut relatively high; the second to the  
desired height.  
Do not mow grass when it is wet. Wet grass will plug  
mower and leave undesirable clumps. Allow grass to  
dry before mowing.  
Always operate engine at full throttle when mow-  
ing to assure better mowing performance and proper  
discharge of material. Regulate ground speed by  
selecting a low enough gear to give the mower cutting  
performance as well as the quality of cut desired.  
6. Engage transmission by placing freewheel control in  
engaged position (See “TO TRANSPORT” in this sec-  
tion of manual).  
7. Sitting in the tractor seat, start engine. After the engine  
is running, move throttle control to half (1/2) speed.  
Disengage parking brake.  
8. Drive tractor forward for approximately five feet then  
backwards for five feet. Repeat this driving procedure  
three times.  
•
•
Your transmission is now purged and now ready for normal  
operation.  
•
When operating attachments, select a ground speed  
that will suit the terrain and give best performance of  
the attachment being used.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
BEFORE  
EACH  
USE  
EVERY  
8
HOURS  
EVERY  
25  
HOURS  
EVERY  
50  
HOURS  
EVERY  
100  
HOURS  
EVERY  
SEASON  
BEFORE  
STORAGE  
MAINTENANCE  
SCHEDULE  
Check Brake Operation  
Check Tire Pressure  
T
R
A
C
T
Check Operator Presence & ROS Systems  
Check for Loose Fasteners  
Check/Replace Mower Blades  
Lubrication Chart  
3
4
0
Check Battery Level  
R
Clean Battery and Terminals  
Clean Debris Off Steering Plate  
Check Transaxle Cooling  
Check Mower Levelness  
Check V-Belts  
5
Check Engine Oil Level  
Change Engine Oil (with oil filter)  
Change Engine Oil (without oil filter)  
Clean Air Filter  
1,2  
1,2  
E
N
G
I
N
E
2
2
Clean Air Screen  
Inspect Muffler/Spark Arrester  
Replace Oil Filter (If equipped)  
Clean Engine Cooling Fins  
Replace Spark Plug  
1,  
2
2
Replace Air Filter Paper Cartridge  
Replace Fuel Filter  
2
1 - Change more often when operating under a heavy load or in high ambient temperatures.  
2 - Service more often when operating in dirty or dusty conditions.  
3 - Replace blades more often when mowing in sandy soil.  
4 - Not required if equipped with maintenance-free battery.  
5 - See Cleaning in Maintenance Section.  
LUBRICATION CHART  
GENERAL RECOMMENDATIONS  
The warranty on this tractor does not cover items that have  
beensubjectedtooperatorabuseornegligence. Toreceive  
full value from the warranty, operator must maintain tractor  
as instructed in this manual.  
SPINDLE ZERK  
SPINDLE ZERK  
➀
➀
➀
FRONT  
WHEEL  
BEARING  
ZERK  
➀
FRONT  
WHEEL  
BEARING  
ZERK  
Some adjustments will need to be made periodically to  
properly maintain your tractor.  
At least once a season, check to see if you should make  
any of the adjustments described in the Service and  
Adjustments section of this manual.  
STEERING  
SECTOR  
GEAR  
➀
ENGINE  
➁
•
At least once a year you should replace the spark plug,  
clean or replace air filter, and check blades and belts  
for wear. A new spark plug and clean air filter assure  
proper air-fuel mixture and help your engine run better  
and last longer.  
TEETH  
MANDREL  
ZERKS  
➀
BEFORE EACH USE  
02501  
•
•
•
•
Check engine oil level.  
Check brake operation.  
Check tire pressure.  
Check operator presence and ROS systems for proper  
operation.  
General Purpose Grease  
➀
➁
Refer to Maintenance “ENGINE” Section  
IMPORTANT: DO NOT OIL OR GREASE THE PIVOT POINTS  
WHICH HAVE SPECIAL NYLON BEARINGS. VISCOUS  
LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL  
SHORTENTHELIFEOFTHESELF-LUBRICATINGBEARINGS.  
IFYOUFEELTHEYMUSTBELUBRICATED, USEONLYADRY,  
POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY.  
•
Check for loose fasteners.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
TRACTOR  
CAUTION:Useonlyareplacementbladeap-  
provedbythemanufacturerofyourtractor.  
Using a blade not approved by the manu-  
facturer of your tractor is hazardous, could  
damageyourtractorandvoidyourwarranty.  
Always observe safety rules when performing any  
maintenance.  
BRAKE OPERATION  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be checked and adjusted. (See  
“TO CHECK BRAKE” in the Service and Adjustments  
section of this manual).  
BLADE REMOVAL (See Fig. 27)  
•
Raise mower to highest position to allow access to  
blades.  
NOTE: Protect your hands with gloves and/or wrap blade  
with heavy cloth.  
TIRES  
•
•
•
Maintain proper air pressure in all tires (See the sides  
•
•
Remove blade bolt by turning counterclockwise.  
Install new or resharpened blade with stamped "THIS  
SIDE UP" facing deck and mandrel assembly.  
of tires for proper PSI).  
Keep tires free of gasoline, oil, or insect control  
chemicals which can harm rubber.  
IMPORTANT: To ensure proper assembly, center hole in blade  
must align with star on mandrel assembly.  
Avoid stumps, stones, deep ruts, sharp objects and  
other hazards that may cause tire damage.  
•
Install and tighten blade bolt securely (45-55 Ft. Lbs.).  
NOTE:Tosealtirepuncturesandpreventflattiresduetoslow  
leaks, tire sealant may be purchased from your local parts  
dealer. Tire sealant also prevents tire dry rot and corrosion.  
IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.  
MANDREL ASSEMBLY  
BLADE  
OPERATOR PRESENCE SYSTEM AND REVERSE  
OPERATION SYSTEM (ROS) (See Fig. 26)  
Be sure operator presence and reverse operation systems  
are working properly. If your tractor does not function as  
described, repair the problem immediately.  
BLADE BOLT  
(SPECIAL)  
STAR  
•
The engine should not start unless the brake pedal is  
fully depressed, and the attachment clutch control is  
in the disengaged position.  
CENTER HOLE  
CHECK OPERATOR PRESENCE SYSTEM  
Fig. 27  
•
•
•
Whentheengineisrunning,anyattemptbytheoperator  
to leave the seat without first setting the parking brake  
should shut off the engine.  
When the engine is running and the attachment clutch  
is engaged, any attempt by the operator to leave the  
seat should shut off the engine.  
BATTERY  
Yourtractorhasabatterychargingsystemwhichissufficient  
for normal use. However, periodic charging of the battery  
with an automotive charger will extend its life.  
•
•
•
•
Keep battery and terminals clean.  
Keep battery bolts tight.  
Keep small vent holes open.  
Recharge at 6-10 amperes for 1 hour.  
The attachment clutch should never operate unless  
the operator is in the seat.  
CHECK REVERSE OPERATION (ROS) SYSTEM  
NOTE:Theoriginalequipmentbatteryonyourtractorismain-  
tenancefree.Donotattempttoopenorremovecapsorcov-  
ers.Addingorcheckinglevelofelectrolyteisnotnecessary.  
•
When the engine is running with the ignition switch in  
the engine "ON" position and the attachment clutch  
engaged, any attempt by the operator to shift into  
reverse should shut off the engine.  
When the engine is running with the ignition switch  
in the ROS "ON" position and the attachment clutch  
engaged, any attempt by the operator to shift into  
reverse should NOT shut off the engine.  
TO CLEAN BATTERY AND TERMINALS  
Corrosion and dirt on the battery and terminals can cause  
the battery to “leak” power.  
•
•
•
Raise hood.  
Disconnect BLACK battery cable first then RED bat-  
tery cable and remove battery from tractor.  
•
•
Rinse the battery with plain water and dry.  
Cleanterminalsandbattery cableends withwirebrush  
until bright.  
•
•
Coat terminals with grease or petroleum jelly.  
Reinstall battery (See “REPLACING BATTERY" in the  
SERVICEANDADJUSTMENTSsectionofthismanual).  
ROS "ON"  
POSITION  
ENGINE "ON" POSITION  
(NORMAL OPERATING)  
Fig. 26  
V-BELTS  
BLADE CARE  
Forbestresultsmowerbladesmustbekeptsharp. Replace  
bent or damaged blades.  
Check V-belts for deterioration and wear after 100 hours  
of operation and replace if necessary. The belts are not  
adjustable. Replace belts if they begin to slip from wear.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
TRANSAXLE MAINTENANCE  
OIL DRAIN VALVE  
The transmission fan and cooling fins should be kept clean  
to ensure proper cooling.  
CLOSED  
AND  
Do not attempt to clean fan or transmission while engine  
is running or while the transmission is hot. To prevent pos-  
sible damage to seals, do not use high pressure water or  
steam to clean transmission.  
LOCKED  
POSITION  
DRAIN  
TUBE  
YELLOW CAP  
•
Inspect cooling fan to be sure fan blades are intact and  
clean.  
•
Inspect cooling fins for dirt, grass clippings and other  
materials.Topreventdamagetoseals,donotusecom-  
pressedairorhighpressuresprayertocleancoolingfins.  
Fig. 28  
•
Unlock drain valve by pushing inward and turning  
counterclockwise.  
To open, pull out on the drain valve.  
After oil has drained completely, close and lock the  
drain valve by pushing inward and turning clockwise  
until the pin is in the locked position as shown.  
TRANSAXLE PUMP FLUID  
•
•
The transaxle was sealed at the factory and fluid mainte-  
nance is not required for the life of the transaxle. Should  
the transaxle ever leak or require servicing, contact your  
nearest authorized service center/department.  
•
•
Remove the drain tube and replace the cap onto to the  
bottom fitting of the drain valve.  
Refill engine with oil through oil fill dipstick tube. Pour  
slowly. Do not overfill. For approximate capacity see  
“PRODUCTSPECIFICATIONS”sectionofthismanual.  
Use gauge on oil fill cap/dipstick for checking level.  
Ensure dipstick cap is tightened securely for accurate  
reading. Keep oil at “FULL” line on dipstick. Tighten  
cap onto the tube securely when finished.  
ENGINE  
LUBRICATION  
Only use high quality detergent oil rated with API service  
classification SG-SL. Select the oil’s SAE viscosity grade  
according to your expected operating temperature.  
•
SAE VISCOSITY GRADES  
SAE 30  
ENGINE OIL FILTER  
5W-30  
Replace the engine oil filter every season or every other oil  
changeifthetractorisusedmorethan100hoursinoneyear.  
-20  
0
30  
32 40  
0
100  
60  
80  
F
C
-20  
10  
-30  
-10  
20  
30  
40  
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE  
CLEAN AIR SCREEN  
Air screen must be kept free of dirt and chaff to prevent  
enginedamagefromoverheating. Cleanwithawirebrushor  
compressedairtoremovedirtandstubborndriedgumfibers.  
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)  
improvestartingincoldweather,theywillresultinincreased  
oilconsumptionwhenusedabove32°F. Checkyourengine  
oil level more frequently to avoid possible engine damage  
from running low on oil.  
AIR FILTER  
Your engine will not run properly using a dirty air filter.  
Service air cleaner more often under dusty conditions.  
Change the oil after every 50 hours of operation or at least  
onceayearifthetractorisnotusedfor50hoursinoneyear.  
ENGINE COOLING SYSTEM  
To ensure proper cooling, make sure the grass screen,  
cooling fins, and other external surfaces of the engine are  
kept clean at all times.  
Check the crankcase oil level before starting the engine  
and after each eight (8) hours of operation. Tighten oil fill  
cap/dipstick securely each time you check the oil level.  
TO CHANGE ENGINE OIL (See Fig. 28)  
Determine temperature range expected before oil change.  
All oil must meet API service classification SG-SL..  
Every 100 hours of operation (more often under extremely  
dusty,dirtyconditions),removetheblowerhousingandother  
coolingshrouds.Cleanthecoolingfinsandexternalsurfaces  
as necessary. Ensure the cooling shrouds are reinstalled.  
NOTE: Operating the engine with a blocked grass screen,  
dirtyorpluggedcoolingfins,and/orcoolingshroudsremoved  
will cause engine damage due to overheating.  
•
•
•
•
Be sure tractor is on level surface.  
Oil will drain more freely when warm.  
Catch oil in a suitable container.  
Remove oil fill cap/dipstick. Be careful not to allow dirt  
to enter the engine when changing oil.  
•
Remove yellow cap from end of drain valve and install  
the drain tube onto the fitting.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
MUFFLER  
DECK WASHOUT PORT (See Fig. 31)  
Your tractor’s deck is equipped with a washout port on  
its surface as part of its deck wash system. It should be  
utilized after each use.  
Inspect and replace corroded muffler and spark arrester (if  
equipped) as it could create a fire hazard and/or damage.  
SPARK PLUGS  
1. Drive the tractor to a level, clear spot on your lawn, near  
enough to a water spigot for your garden hose to reach.  
Replace spark plugs at the beginning of each mowing  
season or after every 100 hours of operation, whichever  
occurs first. Spark plug type and gap setting are shown  
in “PRODUCT SPECIFICATIONS” section of this manual.  
IMPORTANT:Makecertainthetractor’sdischargechuteis  
directed AWAY from your house, garage, parked cars, etc.  
Remove bagger chute or mulch cover if attached.  
2. Make sure the attachment clutch control is in the  
“DISENGAGED” position, set the parking brake, and  
stop the engine.  
IN-LINE FUEL FILTER (See Fig. 29)  
The fuel filter should be replaced once each season. If fuel  
filter becomes clogged, obstructing fuel flow to carburetor,  
replacement is required.  
3. Threadthenozzleadapter(packagedwithyourtractor’s  
Operator’s Manual) onto the end of your garden hose.  
•
•
•
•
With engine cool, remove filter and plug fuel line sec-  
4. Pull back the lock collar of the nozzle adapter and push  
the adapter onto the deck washout port at the left end  
of the mower deck. Release the lock collar to lock the  
adapter on the nozzle.  
tions.  
Place new fuel filter in position in fuel line with arrow  
pointing towards carburetor.  
Be sure there are no fuel line leaks and clamps are  
properly positioned.  
HOSE  
Immediately wipe up any spilled gasoline.  
NOZZLE ADAPTER  
WASHOUT  
PORT  
CLAMP  
FUEL FILTER  
Fig. 29  
CLEANING  
Fig. 31  
•
•
Cleanengine,battery,seat,finish,etc.ofall foreignmatter.  
Clean debris from steering plate. Debris can restrict  
clutch/brake pedal shaft movement, causing belt slip  
and loss of drive.  
IMPORTANT: Tug hose ensuring connection is secure.  
5. Turn the water on.  
6. While sitting in the operator’s position on the tractor,  
re-start the engine and place the throttle lever in the  
Fast " " position.  
CAUTION: Avoid all pinch points and  
movable parts (See Fig. 30)  
IMPORTANT: Recheck the area making certain the area  
is clear.  
CLUTCH/BRAKE PEDAL  
7. Move the tractor’s attachment clutch control to the “EN-  
GAGED”position.Remainintheoperator’spositionwith  
the cutting deck engaged until the deck is cleaned.  
CLEAN  
TOP SIDE  
8. Move the tractor’s attachment clutch control to the  
“DISENGAGED” position. Turn the ignition key to the  
STOP position to turn the tractor’s engine off. Turn the  
water off.  
9. Pull back the lock collar of the nozzle adapter to discon-  
STEERING  
PLATE  
nect the adapter from the nozzle washout port.  
CAUTION:  
PINCH  
POINTS  
10.Move the tractor to a dry area, preferably a concrete or  
paved area. Place the attachment clutch control in the  
“ENGAGED” position to remove excess water and to  
help dry before putting the tractor away.  
STEERING SYSTEM, DASH, FENDER  
AND MOWER NOT SHOWN  
Fig. 30  
•
•
Keep finished surfaces and wheels free of all gasoline,  
oil, etc.  
Protect painted surfaces with automotive type wax.  
WARNING: A broken or missing washout  
fitting could expose you or others to  
thrownobjectsfromcontactwiththeblade.  
We do not recommend using a garden hose or pressure  
washer to clean your tractor unless the engine and trans-  
mission are covered to keep water out. Water in engine or  
transmission will shorten the useful life of your tractor. Use  
compressed air or a leaf blower to remove grass, leaves  
and trash from tractor and mower.  
•
•
Replace broken or missing washout fitting  
immediately, prior to using mower again.  
Pluganyholesinmowerwithboltsandlocknuts.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:  
• Depress brake pedal fully and set parking brake.  
• Place attachment clutch in “DISENGAGED” position.  
• Turn ignition key to “STOP” and remove key.  
• Make sure the blades and all moving parts have completely stopped.  
• Disconnectsparkplugwirefromsparkplugandplacewirewhereitcannotcomeincontact withplug.  
TO REMOVE MOWER (See Fig. 32)  
TO REPLACE MOWER BLADE DRIVE BELT  
(See Fig. 33)  
MOWER DRIVE BELT REMOVAL  
•
•
•
Place attachment clutch in “DISENGAGED” position.  
Lower attachment lift to its lowest position.  
Disengage belt tension rod (K) from lock bracket (L).  
•
•
•
Park tractor on a level surface. Engage parking brake.  
Lower attachment lift to its lowest position.  
Disengage belt tension rod (K) from lock bracket (L).  
CAUTION: Belt tension rod is spring  
loaded. Have a tight grip on rod and  
release slowly.  
CAUTION: Belt tension rod is spring  
loaded. Have a firm grip on rod and  
release slowly.  
•
•
Remove mower belt from electric clutch pulley (M).  
Disconnect front link (E) from mower - remove retainer  
spring and washer.  
•
•
•
Remove screws (P) from mandrel covers (Q) and  
remove covers.  
Removeanydirtorgrassclippingswhichmayhaveaccu-  
mulatedaroundmandrelsandentireupperdecksurface.  
Remove belt from electric clutch pulley (M), both man-  
drel pulleys (R) and all idler pulleys (V).  
•
•
Gotoeithersideofmoweranddisconnectmowersuspen-  
sion arm (A) from chassis and rear lift link (C) from rear  
mowerbracket(D)-removeretainerspringsandwashers.  
Go to other side of mower and disconnect the suspen-  
sion arm and rear lift link.  
CAUTION: After rear lift links are discon-  
nected, the attachment lift lever will be  
spring loaded. Have a tight grip on lift  
leverwhenchangingpositionofthelever.  
MOWER DRIVE BELT INSTALLATION  
•
Install belt around all mandrel pulleys (R) and around  
idler pulleys (V) as shown.  
•
Install belt onto electric clutch pulley (M).  
•
From right side of mower, disconnect anti-sway bar (S)  
from right rear mower bracket (D) - remove retainer  
spring and washer and pull mower toward you until the  
bar falls from the hole in bracket.  
Turn tractor steering wheel to the left as far as it will go.  
Slide mower out from under right side of tractor.  
IMPORTANT: Check belt for proper routing in all mower  
pulley grooves.  
•
Reassemble mandrel covers (Q). Securely tighten all  
screws.  
•
•
•
Engage belt tension rod (K) on locking bracket (L).  
CAUTION: Belt tension rod is spring  
loaded. Have a tight grip on rod and  
engage slowly.  
TO INSTALL MOWER  
Follow procedure described in “INSTALL MOWER AND  
DRIVE BELT” in the Assembly section of this manual.  
•
Raise attachment lift to highest position.  
L
B
M
P
F
P
E
M
P
L
Q
A
K
Q
K
R
H
R
V
C
D
S
C
D
R
Fig. 32  
Fig. 33  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
•
•
If adjustment is necessary, see steps in Visual Adjust-  
TO LEVEL MOWER  
ment instructions above.  
Make sure tires are properly inflated to the PSI shown on  
tires. If tires are over or under inflated, it may affect the  
appearance of your lawn and lead you to think the mower  
is not adjusted properly.  
Recheck measurements, adjust if necessary until both  
sides are equal.  
FRONT-TO-BACK ADJUSTMENT (See Figs. 36 & 37)  
IMPORTANT: Deck must be level side-to-side.  
VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 34)  
To obtain the best cutting results, the mower blades should  
be adjusted so the front tip is 1/8" to 1/2" lower than the  
rear tip when the mower is in its highest position.  
•
With all tires properly inflated and if your lawn appears  
unevenly cut, determine which side of mower is cutting  
lower.  
NOTE: As desired, you can raise the low side of mower  
CAUTION: Blades are sharp. Protect  
your hands with gloves and/or wrap  
blade with heavy cloth.  
or lower the high side.  
•
•
Go to side of mower you wish to adjust.  
With a 3/4" or adjustable wrench, turn lift link adjust-  
ment nut (A) to the left to lower the mower, or, to the  
right to raise the mower.  
•
•
Raise mower to highest position.  
Positionanybladesothetipispointingstraightforward.  
Measure distance (B) to the ground at front and rear  
tip of the blade.  
A
B
B
Fig. 36  
•
•
•
If front tip of blade is not 1/8" to 1/2" lower than the  
rear tip, go to the front of tractor.  
With an 11/16" or adjustable wrench, loosen jam nut  
A several turns to clear adjustment nut B.  
Turn nut left  
Turn nut right  
to lower mower  
to raise mower  
With a 3/4" or adjustable wrench, turn front link adjust-  
mentnut(B)clockwise(tighten)toraisethefrontofmow-  
er,or,counterclockwise(loosen)tolowerthefrontmower.  
Fig. 34  
NOTE: Each full turn of adjustment nut will change mower  
height about 3/16".  
•
Test your adjustment by mowing some uncut grass  
and visually checking the appearance. Readjust, if  
necessary, until you are satisfied with the results.  
B
A
PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 35)  
•
With all tires properly inflated, park tractor on level  
ground or driveway.  
CAUTION: Blades are sharp. Protect  
your hands with gloves and/or wrap  
blade with heavy cloth.  
LOOSEN  
TIGHTEN ADJUST  
ADJUST NUT  
NUT B TO RAISE  
•
•
Raise mower to its highest position.  
B TO LOWER  
MOWER  
MOWER  
At both sides of mower, position blade at side and  
measure the distance (A) from bottom edge of blade  
to the ground. The distance should be the same on  
both sides.  
LOOSEN JAM NUT A FIRST  
Fig. 37  
02966  
NOTE: Each full turn of the adjustment nut will change  
mower height about 1/8".  
•
Recheck measurements, adjust if necessary until front  
tip of blade is 1/8" to 1/2" lower than the rear tip.  
A
A
•
Holdadjustmentnutinpositionwithwrenchandtighten  
jam nut securely against adjustment nut.  
Fig. 35  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO REPLACE MOTION DRIVE BELT  
(See Fig. 38)  
Park the tractor on level surface. Engage parking brake.  
For assistance, there is a belt installation guide decal on  
bottom side of left footrest.  
BELT REMOVAL -  
G
•
Remove mower (See “TO REMOVE MOWER” section  
in this manual).  
NOTE: Observe entire motion drive belt and position of all  
belt guides and keepers.  
•
•
•
Disconnect clutch wire harness (A).  
H
B
Remove anti-rotation link (B) on right side of tractor.  
A
Remove belt from stationary idler (C) and clutching  
idler (D).  
C
J
•
•
Remove belt from centerspan idler (E).  
Pull belt slack toward rear of tractor. Carefully remove  
belt upwards from transmission input pulley and over  
cooling fan blades (F).  
D
E
•
•
Remove belt downward from engine pulley and  
around electric clutch (G).  
Slide belt toward rear of tractor, off the steering plate  
(H) and remove from tractor.  
F
BELT INSTALLATION -  
•
•
•
Install new belt from tractor rear to front, over the steer-  
ing plate (H) and above clutch brake pedal shaft (J).  
02953  
electric  
Pull belt toward front of tractor and roll belt around  
electric clutch and onto engine pulley (G).  
Pull belt toward rear of tractor. Carefully work belt  
down around transmission cooling fan and onto the  
input pulley (F). Be sure belt is inside the belt keeper.  
Fig. 38  
•
•
Install belt on centerspan idler (E).  
Install belt through stationary idler (C) and clutching  
idler (D).  
•
Reinstall anti-rotation link (B) on right side of tractor.  
Tighten securely.  
•
•
Reconnect clutch harness (A).  
Make sure belt is in all pulley grooves and inside all  
belt guides and keepers.  
•
Install mower (See “TO INSTALL MOWER” section in  
this manual).  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
TO CHECK BRAKE  
If tractor requires more than five (5) feet to stop at highest  
speed in highest gear on a level, dry concrete or paved  
surface, then brake must be serviced.  
TO START ENGINE WITH A WEAK BATTERY  
(See Fig. 40)  
WARNING: Lead-acid batteries gen-  
erate explosive gases. Keep sparks,  
flameandsmokingmaterialsawayfrom  
batteries. Always wear eye protection  
when around batteries.  
You may also check brake by:  
•
Park tractor on a level, dry concrete or paved surface,  
depress brake pedal all the way down and engage  
parking brake.  
•
Disengage transmission by placing freewheel control  
in “transmission disengaged” position. Pull freewheel  
control out and into the slot and release so it is held in  
the disengaged position.  
If your battery is too weak to start the engine, it should be  
recharged. (See "BATTERY" in the MAINTENANCE sec-  
tion of this manual).  
If “jumper cables” are used for emergency starting, follow  
this procedure:  
IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12  
VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12  
VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO  
START OTHER VEHICLES.  
The rear wheels must lock and skid when you try to manu-  
ally push the tractor forward. If the rear wheels rotate,  
then the brake needs to be serviced. Contact a qualified  
service center.  
FRONT WHEEL TOE-IN/CAMBER  
TO ATTACH JUMPER CABLES -  
Your new tractor front wheel toe-in and camber is set at the  
factory and is normal. The front wheel toe-in and camber  
are not adjustable. If damage has occurred to affect the  
factory set front wheel toe-in or camber, contact a qualified  
service center.  
•
Connect one end of the RED cable to the POSITIVE  
(+) terminal of each battery(A-B), taking care not to  
short against tractor chassis.  
•
•
ConnectoneendoftheBLACKcabletotheNEGATIVE  
(-) terminal (C) of fully charged battery.  
Connect the other end of the BLACK cable (D) to good  
chassis ground, away from fuel tank and battery.  
TO REMOVE WHEEL FOR REPAIRS  
(See Fig. 39)  
•
•
Block up axle securely.  
TO REMOVE CABLES, REVERSE ORDER -  
•
BLACK cable first from chassis and then from the fully  
charged battery.  
Removeaxlecover,retainingringandwasherstoallow  
wheel removal (rear wheel contains a square key - Do  
not lose).  
Repair tire and reassemble.  
On rear wheels only: align grooves in rear wheel hub  
and axle. Insert square key.  
•
RED cable last from both batteries.  
•
•
•
Replace washers and snap retaining ring securely in  
axle groove.  
•
Replace axle cover.  
NOTE: To seal tire punctures and prevent flat tires due  
to slow leaks, tire sealant may be purchased from your  
local parts dealer. Tire sealant also prevents tire dry rot  
and corrosion.  
WEAK OR  
DEAD BATTERY  
FULLY CHARGED  
BATTERY  
Fig. 40  
WASHERS  
RETAINING  
RING  
AXLE  
COVER  
SQUARE KEY (REAR  
WHEEL ONLY)  
Fig. 39  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
REPLACING BATTERY (See Fig. 41)  
TO REMOVE HOOD AND GRILL ASSEMBLY  
(See Fig. 42)  
WARNING: Do not short battery termi-  
nals by allowing a wrench or any other  
object to contact both terminals at the  
same time. Before connecting battery,  
remove metal bracelets, wristwatch  
bands, rings, etc. Positive terminal  
must be connected first to prevent  
sparking from accidental grounding.  
•
•
•
Raise hood.  
Unsnap headlight wire connector.  
Standinfrontoftractor. Grasphoodatsides, tilttoward  
engine and lift off of tractor.  
•
To replace, reverse above procedure.  
•
•
•
Lift hood to raised position.  
Remove terminal cover.  
Disconnect BLACK battery cable then RED battery  
cable and carefully remove battery from tractor.  
HOOD  
•
Install new battery with terminals in same position as  
old battery.  
•
•
Reinstall terminal cover.  
First connect RED battery cable to positive (+) battery  
terminal with bolt and nut as shown. Tighten securely.  
HEADLIGHT  
WIRE  
CONNECTOR  
•
•
ConnectBLACKgroundingcabletonegative(-)battery  
terminal with remaining bolt and nut. Tighten securely  
Close hood.  
07002  
NEGATIVE  
(BLACK)  
CABLE  
TERMINAL  
COVER  
Fig. 42  
TRANSMISSION  
POSITIVE  
(RED)  
CABLE  
REMOVAL/REPLACEMENT  
Should your transmission require removal for service or  
replacement, it should be purged after reinstallation and  
beforeoperatingthetractor. See“PURGETRANSMISSION”  
in the Operation section of this manual.  
Fig. 41  
ENGINE  
TO REPLACE HEADLIGHT BULB  
TO ADJUST THROTTLE CONTROL CABLE  
The throttle control has been preset at the factory and  
adjustment should not be necessary. If adjustment is nec-  
essary, see engine manual.  
•
•
Raise hood.  
Pull bulb holder out of the hole in the backside of the  
grill.  
Replace bulb in holder and push bulb holder securely  
back into the hole in the backside of the grill.  
Close hood.  
•
•
TO ADJUST CHOKE CONTROL  
Thechokecontrolhasbeenpresetatthefactoryandadjust-  
ment should not be necessary. If adjustment is necessary,  
see engne manual.  
INTERLOCKS AND RELAYS  
Loose or damaged wiring may cause your tractor to run  
poorly, stop running, or prevent it from starting.  
•
Check wiring.  
TO ADJUST CARBURETOR  
Your carburetor is not adjustable. If your engine does not  
operate properly due to suspected carburetor problems,  
take your tractor to an authorized service center for repair  
and/or adjustment.  
TO REPLACE FUSE  
Replace with 20 amp automotive-type plug-in fuse. The  
fuse holder is located behind the dash.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
Immediately prepare your tractor for storage at the end  
of the season or if the tractor will not be used for 30 days  
or more.  
ENGINE  
FUEL SYSTEM  
IMPORTANT: ITISIMPORTANTTOPREVENTGUMDEPOSITS  
FROMFORMINGINESSENTIALFUELSYSTEMPARTSSUCH  
AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK  
DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT  
ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING  
ETHANOLORMETHANOL)CANATTRACTMOISTUREWHICH  
LEADSTOSEPARATIONANDFORMATIONOFACIDSDURING  
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM  
OF AN ENGINE WHILE IN STORAGE.  
WARNING: Neverstorethetractorwith  
gasoline in the tank inside a building  
where fumes may reach an open flame  
orspark. Allowtheenginetocoolbefore  
storing in any enclosure.  
TRACTOR  
•
•
•
Empty the fuel tank by starting the engine and let it run  
until the fuel lines and carburetor are empty.  
Never use engine or carburetor cleaner products in  
the fuel tank or permanent damage may occur.  
Remove mower from tractor for winter storage. When  
mower is to be stored for a period of time, clean it thor-  
oughly, remove all dirt, grease, leaves, etc. Store in a  
clean, dry area.  
Use fresh fuel next season.  
•
Clean entire tractor (See “CLEANING” in the Mainte-  
nance section of this manual).  
NOTE: Fuel stabilizer is an acceptable alternative in mini-  
mizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not empty  
the gas tank and carburetor if using fuel stabilizer.  
•
Inspect and replace belts, if necessary (See belt re-  
placement instructions in the Service and Adjustments  
section of this manual).  
•
•
Lubricate as shown in the Maintenance section of this  
manual.  
Be sure that all nuts, bolts and screws are securely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
ENGINE OIL  
Drain oil (with engine warm) and replace with clean engine  
oil. (See “ENGINE” in the Maintenance section of this  
manual).  
•
Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
BATTERY  
CYLINDER(S)  
•
•
Fully charge the battery for storage.  
•
•
Remove spark plug(s).  
After a period of time in storage, battery may require  
recharging.  
Pour one ounce of oil through spark plug hole(s) into  
cylinder(s).  
•
To help prevent corrosion and power leakage during  
long periods of storage, battery cables should be dis-  
connected and battery cleaned thoroughly (see “TO  
CLEAN BATTERY AND TERMINALS” in the Mainte-  
nance section of this manual).  
After cleaning, leave cables disconnected and place  
cables where they cannot come in contact with battery  
terminals.  
•
•
Turn ignition key to “START” position for a few seconds  
to distribute oil.  
Replace with new spark plug(s).  
OTHER  
•
•
•
•
Do not store gasoline from one season to another.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
If possible, store your tractor indoors and cover it to  
give protection from dust and dirt.  
Cover your tractor with a suitable protective cover that  
does not retain moisture. Do not use plastic. Plastic  
cannot breathe which allows condensation to form and  
will cause your tractor to rust.  
If battery is removed from tractor for storage, do not  
store battery directly on concrete or damp surfaces.  
•
•
IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE  
AND EXHAUST AREAS ARE STILL WARM.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
1. Out of fuel.  
1. Fill fuel tank.  
Will not start  
2. Engine not “CHOKED” properly.  
3. Engine flooded.  
4. Bad spark plug.  
5. Dirty air filter.  
2. See “TO START ENGINE” in Operation section.  
3. Wait several minutes before attempting to start.  
4. Replace spark plug.  
5. Clean/replace air filter.  
6. Dirty fuel filter.  
6. Replace fuel filter.  
7. Water in fuel.  
7. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
8. Loose or damaged wiring.  
8. Check all wiring.  
9. Carburetor out of adjustment.  
9. See “To Adjust Carburetor” in Service Adjustments  
section.  
10. Engine valves out of adjustment.  
10. Contact an authorized service center/department.  
1. Dirty air filter.  
2. Bad spark plug.  
1. Clean/replace air filter.  
2. Replace spark plug.  
Hard to start  
3. Weak or dead battery.  
4. Dirty fuel filter.  
3. Recharge or replace battery.  
4. Replace fuel filter.  
5. Stale or dirty fuel.  
6. Loose or damaged wiring.  
7. Carburetor out of adjustment.  
5. Empty fuel tank and refill tank with fresh, clean gas.  
6. Check all wiring.  
7. See “To Adjust Carburetor” in Service Adjustments  
section.  
8. Engine valves out of adjustment.  
8. Contact an authorized service center/department.  
1. Brake pedal not depressed.  
2. Attachment clutch is engaged.  
3. Weak or dead battery.  
1. Depress brake pedal.  
Engine will not  
turn over  
2. Disengage attachment clutch.  
3. Recharge or replace battery.  
4. Replace fuse.  
4. Blown fuse.  
5. Corroded battery terminals.  
6. Loose or damaged wiring.  
7. Faulty ignition switch.  
8. Faulty solenoid or starter.  
9. Faulty operator presence switch(es).  
5. Clean battery terminals.  
6. Check all wiring.  
7. Check/replace ignition switch.  
8. Check/replace solenoid or starter.  
9. Contact an authorized service center/department.  
1. Weak or dead battery.  
1. Recharge or replace battery.  
2. Clean battery terminals.  
3. Check all wiring.  
Engine clicks but  
will not start  
2. Corroded battery terminals.  
3. Loose or damaged wiring.  
4. Faulty solenoid or starter.  
4. Check/replace solenoid or starter.  
1. Cutting too much grass/too fast.  
2. Throttle in “CHOKE” position.  
1. Raise cutting height/reduce speed.  
2. Adjust throttle control.  
Loss of power  
3. Build-upofgrass,leaves,trashundermower. 3. Clean underside of mower housing.  
4. Dirty air filter.  
4. Clean/replace air filter.  
5. Low oil level/dirty oil.  
6. Faulty spark plug.  
7. Dirty fuel filter.  
5. Check oil level/change oil.  
6. Clean and regap or change spark plug.  
7. Replace fuel filter.  
8. Stale or dirty fuel.  
9. Water in fuel.  
8. Empty fuel tank and refill tank with fresh, clean gas.  
9. Empty fuel tank and carburetor, refill tank with fresh  
gasoline and replace fuel filter.  
10. Spark plug wire loose.  
10. Connect and tighten spark plug wire.  
11. Dirty engine air screen/fins.  
12. Dirty/clogged muffler.  
11. Clean engine air screen/fins.  
12. Clean/replace muffler.  
13. Loose or damaged wiring.  
14. Carburetor out of adjustment.  
15. Engine valves out of adjustment.  
13. Check all wiring.  
14. See “To Adjust Carburetor” in Service Adjustments  
15. Contact an authorized service center/department.  
1. Worn, bent or loose blade.  
2. Bent blade mandrel.  
3. Loose/damaged part(s).  
1. Replace blade. Tighten blade bolt.  
2. Replace blade mandrel.  
3. Tighten loose part(s). Replace damaged parts.  
Excessive  
vibration  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING POINTS  
PROBLEM  
CAUSE  
CORRECTION  
1. Faulty operator-safety presence control  
system.  
1. Check wiring, switches and connections. If not  
corrected, contact an authorized service center/  
department.  
Engine continues  
to run when oper-  
ator leaves seat  
with attachment  
clutch engaged  
1. Worn, bent or loose blade.  
2. Mower deck not level.  
1. Replace blade. Tighten blade bolt.  
2. Level mower deck.  
Poor cut - uneven  
3. Buildup of grass, leaves, trash under mower. 3. Clean underside of mower housing.  
4. Bent blade mandrel.  
4. Replace blade mandrel.  
5. Clogged mower deck vent holes from  
buildup of grass, leaves, and trash around  
mandrels.  
5. Clean around mandrels to open vent holes.  
1. Obstruction in clutch mechanism.  
2. Worn/damaged mower drive belt.  
3. Frozen idler pulley.  
1. Remove obstruction.  
2. Replace mower drive belt.  
3. Replace idler pulley.  
Mower blades will  
not rotate  
4. Frozen blade mandrel.  
4. Replace blade mandrel.  
1. Engine speed too slow.  
2. Travel speed too fast.  
3. Wet grass.  
4. Mower deck not level.  
5. Low/uneven tire air pressure.  
6. Worn, bent or loose blade.  
1. Place throttle control in “FAST” position.  
2. Shift to slower speed.  
3. Allow grass to dry before mowing.  
4. Level mower deck.  
5. Check tires for proper air pressure.  
6. Replace blade. Tighten blade bolt.  
Poor grass  
discharge  
7. Buildup of grass, leaves, trash under mower. 7. Clean underside of mower housing.  
8. Mower drive belt worn.  
9. Blades improperly installed.  
10. Improper blades used.  
8. Replace mower drive belt.  
9. Reinstall blades sharp edge down.  
10. Replace with blades listed in parts manual.  
11. Cloggedmowerdeckventholesfrombuildup 11. Clean around mandrels to open vent holes.  
of grass, leaves, trash around mandrels.  
1. Switch is “OFF”.  
1. Turn switch “ON”.  
Headlight(s) not  
working  
(if so equipped)  
2. Bulb(s) or lamp(s) burned out.  
3. Faulty light switch.  
4. Loose or damaged wiring.  
5. Blown fuse.  
2. Replace bulb(s) or lamp(s).  
3. Check/replace light switch.  
4. Check wiring and connections.  
5. Replace fuse.  
1. Bad battery cell(s).  
1. Replace battery.  
2. Check/clean all connections.  
3. Replace regulator.  
Battery will not  
charge  
2. Poor cable connections.  
3. Faulty regulator (if so equipped).  
4. Faulty alternator.  
4. Replace alternator.  
1. Freewheel control in “disengaged” position.  
2. Debris on steering plate (if equipped).  
1. Place freewheel control in “engaged” position.  
2. See "CLEANING" in the maintenance section.  
Loss of drive  
3. Motion drive belt worn, damaged, or broken. 3. Replace motion drive belt.  
4. Air trapped in transmission during  
shipment or servicing.  
4. Purge transmission.  
5. Axle key missing.  
5. Install axle key at rear wheel. See "TO REMOVE  
WHEEL" in the Service and Adjustments section.  
1. Engine throttle control not set between  
half and full speed (fast) position before  
stopping engine.  
1. Move throttle control between half and full speed  
(fast) position before stopping engine.  
Engine "back-  
fires” when turn-  
ing engine “OFF”  
1. Reverseoperationsystem(ROS)isnot"ON" 1. Turn ignition key to ROS "ON" position. See  
Engine dies when  
tractor is shifted  
into reverse  
whilemowerorotherattachmentisengaged.  
Operation section.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
SCHEMATIC  
SCH12  
BATTERY  
SOLENOID  
STARTER  
RED  
A
M
RED  
FUSE  
AMMETER  
(OPTIONAL)  
BLACK  
ELECTRIC CLUTCH  
WHITE  
BLACK  
WHITE  
PTO SWITCH  
(DISENGAGED)  
S
H
WHITE  
BLACK  
RED  
M
B
G
C
A
B
A1  
GRAY  
A2  
L
RED  
CLUTCH/BRAKE  
(PEDAL UP)  
D
E
REVERSE SWITCH  
(NOT IN REVERSE)  
BLACK  
BLACK  
BLACK  
2
BLACK  
BLACK  
SEAT SWITCH  
(NOT OCCUPIED)  
BLACK  
BLACK  
3
1
GRAY  
6
JUNCTION  
CONNECTOR  
SHORTING  
CONNECTOR  
CHASSIS  
HARNESS  
H
G
C F  
SPARK  
IGNITION  
UNIT  
PLUGS GAP  
(2 PLUGS ON  
TWIN CYL. ENGINES)  
B
A
E
(OPTIONAL)  
BLUE  
BLACK  
HOUR  
METER  
D
BLACK  
BLUE  
FUEL  
LINE  
12V  
PTO SWITCH  
(MATING SIDE)  
POWER OUTLET  
(OPTIONAL)  
BLUE  
CHARGING SYSTEM OUTPUT  
9 - 1 6 AMP DC @ 3600 RPM  
FUEL SHUT-OFF  
SOLENOID  
(IF EQUIPPED)  
RED  
REGULATOR  
STATOR  
28 VOLTS AC @ 3600 RPM (REGULATOR DISCONNECTED)  
BLACK  
BROWN  
LIGHT  
SWITCH  
HEADLIGHTS  
WIRING INSULATED CLIPS  
NOTE: IF WIRING INSULATED  
CLIPS WERE REMOVED FOR  
SERVICING OF UNIT, THEY  
SHOULD BE RE-INSTALLED TO  
PROPERLY SECURE YOUR  
WIRING.  
3
6
6
5
3
2
IGNITION SWITCH  
NON-REMOVABLE  
CONNECTIONS  
2
1
5
4
POSITION CIRCUIT “MAKE”  
4
1
OFF  
M+G+A1  
B+A1  
RUN/OVERRIDE  
REMOVABLE  
CONNECTIONS  
CHASSIS HARNESS  
CONNECTOR  
DASH HARNESS  
CONNECTOR  
RUN  
B+A1  
L+A2  
START  
B + S + A1  
(MATING SIDE)  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
ELECTRICAL  
T11S  
33  
22  
90  
30  
79  
21  
27  
2
1
24  
91  
99  
100  
34  
8
27  
43  
42  
41  
40  
26  
25  
55  
28  
16  
With 12V Outlet Option  
103  
71  
59  
102  
29  
With Service Minder Option  
105  
46  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
ELECTRICAL  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 16 34-65 Battery  
874 76 04-12 Bolt Hex Head 1/4-20 x 3/4  
532 41 41-25 Box Battery  
2
8
16  
21  
22  
24  
25  
26  
27  
28  
29  
30  
33  
34  
40  
41  
42  
43  
46  
50  
55  
71  
79  
90  
91  
99  
532 17 61-38 Switch Interlock Push-In  
532 40 02-52 Harness Socket Light w/4152J  
532 00 41-52 Bulb Light  
532 40 02-53 Cable Battery  
532 41 28-95 Cable Starter  
532 17 51-58 Fuse  
873 51 04-00 Nut Keps Hex 1/4-20 unc  
532 14 54-91 Cable, Ground  
532 40 15-45 Switch, Seat  
532 19 33-50 Switch, Ign  
532 41 19-33 Key\Chain  
532 11 07-12 Switch Light / Reset  
532 40 11-04 Harness Ign. Dash  
817 72 04-08 Screw Thd Cut 1/4-20 x 1/2  
532 13 15-63 Cover, Terminal  
532 19 25-07 Solenoid  
532 40 17-63 Gauge Servicereminder Hrmtr  
532 17 46-51 Switch PTO  
817 06 05-12 Screw Thdrol 5/16-18 x 3/4 TYTT  
532 19 42-76 Harness Ign. Chassis  
532 17 52-42 Socket Asm Bulb Twistlock  
532 43 53-95 Cover Terminal  
532 19 02-70 Strap Battery Mount  
817 67 04-12 Screw Hexwsh Thdrol 1/4-20 x 3/4  
100 819 09 14-16 Washer 9/32 x 7/8 x 16 Ga.  
102 532 40 44-54 Harness Pigtail  
105 532 40 75-68 Switch Reverse TT Pedal Control  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
CHASSIS  
297  
208  
15  
204  
18  
203  
130  
191  
214  
14  
207  
206  
130  
25  
137  
5
176  
202  
150  
137  
176  
151  
205  
176  
175  
177  
178  
195  
176  
286  
283  
284  
176  
182  
130  
285  
194  
235  
213  
218  
34  
68  
36  
236  
130  
199  
161  
36  
194  
68  
68  
68  
183  
37  
180  
228  
165  
282  
287  
217  
282  
189  
162  
194  
58  
233  
52  
228  
189  
152  
189  
233  
189  
Chassis-tex_GT HUSQ_II_41  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
CHASSIS  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
3
532 43 97-52  
Applique Subasm.  
Dash  
194 873 90 05-00  
195 532 40 41-37  
199 532 41 34-85  
202 532 43 97-28  
203 532 43 97-27  
204 532 43 57-14  
205 532 43 97-30  
206 532 43 97-29  
207 532 43 97-34  
208 532 43 97-35  
213 874 76 05-12  
214 532 19 91-45  
217 532 40 91-67  
218 532 19 63-95  
228 532 19 51-61  
233 532 19 65-39  
235 532 40 61-29  
236 873 93 05-00  
282 532 41 41-10  
283 532 43 98-23  
284 532 43 98-61  
285 532 41 63-15  
286 532 41 63-17  
287 817 60 04-06  
297 532 43 74-56  
Nut Lock Hex Flange 5/16-18  
Plug 12 V Adapter  
Plate Deck Lift  
Vent Side Hood RH  
Vent Side Hood LH  
Vent Top Hood  
5
532 43 74-71  
532 44 11-77  
532 43 97-33  
532 43 77-62  
532 43 97-32  
532 19 61-25  
817 06 05-12  
532 44 11-78  
873 68 05-00  
532 41 22-80  
817 49 05-08  
14  
15  
18  
25  
34  
36  
37  
52  
58  
68  
Hood  
Lens LH  
Grille  
Lens RH  
Plate Engine  
Skirt Hood Side RH  
Skirt Hood Side LH  
Bezel RH  
Screw 5/16-18 x 3/4  
Fender  
Nut Lock 5/16-18  
Drawbar Upper  
Screw 5/16-18 x 1/2  
Screw #10 x 0.750 BOS Thread  
Bumper Dash  
Air Duct  
Bezel LH  
Bolt 5/16-18 unc x 3/4  
Clip Retainer Tinner  
Rod Pivot  
130 532 41 63-58  
137 532 40 75-90  
150 532 43 97-74  
151 532 43 66-70  
152 532 19 95-35  
161 532 43 97-81  
162 532 14 24-32  
165 532 19 68-26  
175 532 19 63-04  
176 532 40 07-76  
177 532 19 52-27  
178 532 19 97-82  
180 532 41 50-63  
182 532 40 68-59  
183 874 52 05-20  
189 817 00 05-12  
191 532 43 74-55  
X-Piece Hood Stop  
Stud Fastner  
Pivot Bracket  
Shield Browning  
Window Fuel  
Screw  
Bolt Shoulder  
Spacer Fender  
Nut Lock 5/16-18 unc  
Clip Retainer Console  
Console Asm. Decklift  
Console Asm.  
Support Tank Rear  
Crossmember  
Screw 10-24 x 5/8  
Bushing Steering  
Cargo Net Asm.  
Chassis  
Console Insert RH  
Console Insert LH  
Screw Hex Washead 1/4-20 x 3/8  
Insert Reflective LH  
Dash Lower  
Bolt 5/16-18 x 1-1/4  
Screw 5/16-18 x 3/4  
Insert Reflective RH  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
DRIVE  
207  
221  
206  
125  
116  
92  
213  
56  
160  
26  
209  
143  
185  
216  
197  
125  
196  
221  
42  
184  
125  
35  
80  
125  
170  
227  
64  
231  
51  
167  
226  
159  
160  
214  
210  
125  
153  
208  
49  
185  
186  
211  
188  
159  
222  
189  
187  
163  
215  
161  
29  
211  
50  
125  
15  
166  
153  
17  
183  
190  
33  
51  
116  
52  
2
225  
51  
230  
205  
116  
183  
2
205  
33  
1
73  
73  
99  
drive-tex_K46_pedal_39_r1  
230  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
DRIVE  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
- - - - - - - - - - Transaxle, TUFFTORQ K46  
532 12 35-83 Key  
184 532 44 14-55 Handle Parking Brake  
185 872 11 06-22 Bolt Rdhd Sqnk 3/8-16 x 2-3/4 Gr. 5  
186 532 19 43-21 Spacer Retainer  
2
15  
17  
26  
29  
33  
35  
42  
49  
50  
51  
52  
56  
64  
73  
80  
92  
99  
819 13 13-16 Washer 13/32 x 13/16 x 16 Ga.  
532 41 36-78 Spring, Brake  
187 819 13 32-10 Washer  
532 19 96-79 Spring Return Cruise  
532 40 38-06 Rod, Brake  
812 00 00-01 Ring E  
188 532 19 43-23 Link Clutch Ground Drive  
189 532 19 43-17 Bellcrank Ground Drive  
190 532 19 43-18 Keeper Bellcrank Ground Drive  
196 817 00 06-16 Screw 3/8-16 x 1  
197 532 19 58-04 Bracket Clutch Anti-Rotation  
205 532 12 17-48 Washer  
206 532 19 78-67 Bracket Mount Latch Cruise  
207 532 19 78-68 Latch Control Cruise  
208 532 19 78-69 Gear Sector Control Cruise  
209 532 19 95-92 Rod Control Cruise  
210 532 40 09-80 Rocker Asm. Pedal Control  
211 532 12 01-83 Bearing Nylon  
532 43 54-86 Rod, Brake, Park  
532 12 48-72 Cover, Foot Pedal  
872 11 06-14 Bolt  
532 19 43-27 Pulley Idler Flat  
873 90 06-00 Lock Nut 3/8-16  
532 19 43-26 Idler V-Groove 910" Offset  
532 13 09-69 V-Belt, Drive  
532 19 78-65 Shaft Asm. Pedal Brake Control  
874 49 05-40 Bolt Hex Flghd 5/16-18 x 2.1/2 G5  
532 44 06-19 Bracket Strap Torque  
874 76 05-20 Bolt Fin Hex 5/16-18 unc x 1.25  
532 41 57-42 Rod Spring Bypass  
213 532 40 31-19 Knob Control Cruise  
214 532 42 12-63 Pedal Forward  
215 532 40 17-23 Pedal Reverse  
116 873 90 05-00 Nut Lock Hex Flange 5/16-18  
125 817 00 05-12 Screw 5/16-18 x 3/4  
143 817 49 05-08 Screw 5/16-18 x 1/2  
153 532 12 47-88 Retainer Spring  
159 876 02 04-12 Pin Cotter 1/8 x 3/4  
160 532 16 94-84 Retainer Clip  
161 532 10 57-09 Spring, Return, Clutch  
163 532 40 10-34 Rod Pedal Control  
166 532 42 91-64 Nut Push  
216 532 19 61-31 Bracket Pulley Idler  
221 532 40 31-87 Retainer Spring Clip Handle  
222 879 21 20-10 Washer 21/32 x 1-1/4 x 10 Ga.  
225 532 40 33-19 Keeper Belt Trans.  
226 532 40 15-64 Bracket Mount Touque  
227 817 49 05-12 Screw 5/16-18 x 3/4  
230 532 18 89-67 Washer Hardened  
231 532 40 72-87 Idler V-Groove  
167 532 40 52-57 Latch Brake Parking  
170 532 41 34-30 Keeper Belt Centerspan  
183 532 13 70-57 Spacer Split  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
ENGINE  
1
21  
87  
62  
20  
69  
71  
45  
81  
91  
37  
84  
82  
84  
18  
12  
28  
37  
70  
11  
15  
79  
41  
42  
85  
2
9
90  
29  
SPARK ARRESTER KIT  
engine-tex_bs-2cyl_47_r1  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
ENGINE  
KEY PART  
NO. NO.  
DESCRIPTION  
1
- - - - - -  
Engine Briggs & Stratton Model  
No. 44P777-1553-G1  
Muffler  
2
9
532 14 97-23  
532 19 43-20  
532 40 00-08  
532 40 50-97  
532 41 41-51  
532 43 92-08  
532 42 35-02  
532 41 63-58  
532 40 11-35  
532 13 71-80  
532 12 34-87  
532 12 61-97  
810 04 07-00  
873 51 04-00  
532 43 40-17  
532 16 53-91  
532 15 99-55  
532 16 05-89  
532 18 39-06  
532 14 84-56  
532 42 82-87  
817 06 06-20  
532 17 39-37  
537 17 18-77  
817 00 06-16  
532 18 74-95  
Keeper Belt Engine  
Clutch  
11  
12  
15  
18  
20  
21  
28  
29  
37  
41  
42  
45  
62  
69  
70  
71  
79  
81  
82  
84  
85  
87  
90  
91  
Pulley Engine  
Tank Fuel  
Cap Asm Fuel  
Control Throttle/Choke  
Screw #10 x .750 BOS Thread  
Fuel Line  
Spark Arrester Kit  
Clamp Hose  
Washer1-1/2ODx15/32IDx.250  
Washer Lock 7/16  
Nut Keps Hex 1/4-20 unc  
Heat Shield  
Gasket  
Exhaust Tube LH  
Exhaust Tube RH  
Screw Socket Head 5/16-18 x1  
Tube Drain Oil  
Valve Oil Drain  
Screw 3/8-16 x 1-1/4  
BoltHex7/16-20x4xGr.5-1.5Thr  
Bolt 5/16-18 unc x 3/4 w/Sems  
Screw 3/8-16 x 1  
Bushing  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
For engine service and replacement parts, call the toll free  
number for your engine manufacturer listed below:  
Briggs & Stratton  
1-800-233-3723  
Engine Power Rating Information  
The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive En-  
gineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and  
corrected in accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060 RPM; horsepower values  
are derived at 3600 RPM. Actual gross engine power will be lower and is affected by, among other things, ambient operat-  
ing conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and  
the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross  
power when used in a given piece of power equipment (actual “on-site” or net power). This difference is due to a variety  
of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.),  
application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability.  
Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this  
Series engine.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
STEERING ASSEMBLY  
26  
45  
51  
1
63  
19  
57  
60  
63  
21  
59  
16  
35  
9
58  
6
8
7
67  
66  
8
64  
2
9
28  
13  
7
22  
61  
4
6
67  
14  
15  
62  
5
69  
13  
68  
70  
14  
15  
53  
8
steering-tex_HUSQHR_4  
13  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
STEERING ASSEMBLY  
KEY PART  
NO. NO.  
DESCRIPTION  
1
532 43 97-40 Wheel, Steering  
2
532 19 59-68 Axle Asm., Front  
4
532 40 30-87 Spindle Asm., LH  
532 40 30-88 Spindle Asm., RH  
532 12 49-31 Bearing, Race Thrust Harden  
532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga.  
812 00 00-29 Ring, Klip #T5304-75  
532 12 12-32 Cap, Spindle  
5
6
7
8
9
13  
14  
15  
16  
19  
21  
22  
26  
28  
35  
45  
51  
53  
57  
58  
59  
60  
61  
62  
63  
64  
66  
67  
68  
69  
70  
532 12 17-49 Washer 25/32 x 1-1/4 x 16 Ga.  
810 04 06-00 Washer, Lock Hvy Hlcl Spr 3/8  
873 54 06-00 Nut, Crown Lock 3/8-24 unf  
532 40 82-19 Shaft Steering  
532 19 47-29 Plate Steering  
532 18 67-37 Adapter, Wheel Steering  
532 42 05-37 Strg. Supt. Lower  
532 43 97-43 Insert, Wheel Steering  
817 00 06-12 Screw 3/8-16 x 3/4  
532 19 47-32 Gear, Sector Plate  
819 18 38-12 Washer 9/16 ID x 2-3/8 OD 12 Ga.  
873 94 08-00 Nut Hex Jam Toplock 1/2-20 unf  
532 18 89-67 WasherHardened.793x1.637x.060  
532 19 72-46 Bracket Upstop  
532 19 47-47 Bolt Shoulder Sector Pivot CFM  
532 19 47-48 Washer Thrust Sector Steering  
873 97 10-00 Nut Flange Lock 5/8-11  
532 19 47-40 Draglink LH  
532 19 47-41 Draglink, RH  
817 00 05-12 Screw 5/16-18 x 3/4  
532 19 98-49 Retainer Clip Spring Steering  
871 02 07-48 Bolt Hex Fghd 7/16-14 x 3 Serr  
532 19 47-37 Bushing PM Front Axle  
873 90 07-00 Nut Lock Flange 7/16-14 Gr. 5  
532 19 91-62 Washer 1.5 x .505 x .118  
532 19 61-97 Bracket Deck Susp. Front  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
SEAT ASSEMBLY  
1
8
8
7
7
8
41  
40  
8
10  
6
21  
37  
37  
44  
43  
2
21  
3
seat-tex_6.5SL_2  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
37  
40  
41  
43  
44  
873 80 05-00 Nut, Lock 5/16-18 unc  
532 19 76-61 Handle Slide Seat  
1
532 42 40-68 Seat  
2
532 18 01-66 Bracket Pivot Fender  
532 14 06-75 Strap, Asm Fender  
532 19 82-00 Spring Latch Seat  
3
874 76 06-12 Bolt Fin Hex 3/8-16 unc x 3/4  
819 13 38-12 Washer 13/32 x 2-3/8 x 12 Ga.  
6
873 80 06-00 Nut, Lock W/Ins. 3/8-16 unc  
532 12 41-81 Spring, Seat Cprsn  
532 17 18-77 Bolt 5/16-18 unc x 3/4 w/Sems  
532 19 69-77 Pan, Seat  
7
8
10  
21  
NOTE: All component dimensions given in U.S. inches  
532 17 18-52 Bolt, Shoulder 5/16-18  
1 inch = 25.4 mm  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
MOWER LIFT  
87  
87  
7
90  
98  
89  
3
10  
88  
97  
2
91  
97  
91  
87  
89  
lift-tex_23  
89  
87  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
90  
91  
97  
98  
532 19 42-08 Pin Cotter 5/16 Bow Tie Lock  
532 40 34-07 Link Lift Susp Mower Rear  
817 00 06-12 Screw 3/8-16 x 3/4  
2
532 42 20-27 Shaft Asm., Lift  
532 19 52-31 Lever Lift Handle  
532 41 15-55 Grip, Lever  
3
7
532 19 52-64 Link Asm. Susp. Front Mower  
10  
87  
88  
89  
532 19 63-14 Spring Torsion  
532 19 42-09 Pin Cotter 7/16 Bow Tie Lock  
532 41 07-10 Spring Lift Assist  
819 19 19-12 Washer Clear Zinc  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
MOWER DECK  
ꢁꢇ  
ꢁꢇ  
ꢁꢅ  
ꢃꢄꢀ  
ꢈꢆ  
ꢇ
ꢈꢁ  
ꢃꢆꢉ  
ꢁꢆ  
ꢁꢇ  
ꢉꢃ  
ꢃꢉꢉ  
ꢀꢉ  
ꢅ
ꢃꢃꢁ  
ꢁꢈ  
ꢃꢆꢇ  
ꢁꢆ  
ꢆꢅ  
ꢈꢈ  
ꢈꢃ  
ꢈꢈ  
ꢆꢄ  
ꢈꢉ  
ꢀꢉ  
ꢈꢉ  
ꢉꢁꢃ  
ꢈꢈ  
ꢈꢃ  
ꢃ
ꢉꢁꢉ  
ꢈꢊ  
ꢃꢃꢇ  
ꢃꢃꢅ  
ꢃꢉꢊ  
ꢁꢆ  
ꢉꢆ  
ꢀꢊ  
ꢉꢀ  
ꢃꢃꢈ  
ꢉꢃ  
ꢉꢇ  
ꢉꢁ  
ꢃꢆꢁ  
ꢃꢉ  
ꢃꢇ  
ꢃꢆ  
ꢉꢃ  
ꢉꢅ  
ꢉꢃ  
ꢉꢃ  
ꢇꢊ  
ꢉꢃ  
ꢀꢆ  
ꢃꢄ  
ꢃꢄ  
ꢃꢄ  
ꢀꢄ  
ꢃꢄ  
ꢃꢄ  
ꢃꢄ  
ꢃꢆꢊ  
ꢃꢀ  
ꢃꢄꢆ  
ꢉꢃ  
ꢃꢁ  
ꢃꢃ  
ꢉꢃ  
ꢃꢄ  
ꢃꢆꢊ  
ꢃꢈ  
ꢃꢄꢅ  
ꢃꢄꢄ  
ꢄ
ꢃꢄꢅ  
MOWER?DECKªꢀꢁꢂTEX?ꢃꢄ?Rꢃ  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
MOWER DECK  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
1
532 44 15-47 Deck Weldment Mower  
532 19 60-66 Cover Mandrel LH  
532 19 71-81 Cover Mandrel RH  
532 19 30-03 Bolt 7/16 Asm. Blade  
532 18 72-56 Blade Bagging  
59  
60  
97  
98  
532 18 73-44 Baffle Left  
6
532 18 76-07 Baffle Center  
532 17 85-15 Washer Hardened  
532 19 61-05 Spring Drive  
7
8
11  
12  
13  
14  
16  
15  
18  
19  
21  
24  
25  
26  
27  
29  
30  
31  
32  
33  
34  
39  
43  
46  
47  
49  
50  
52  
58  
113 872 11 05-08 Bolt Rdhd Sqnk 5/16-18 x 3/4  
114 532 18 75-56 Rod Tension Relief  
532 40 48-51 Rod Anti Sway  
532 18 72-91 Shaft Asm. w/Lower Bearing  
532 18 72-81 Housing, Mandrel  
819 13 13-12 Washer 3/8  
116 532 19 34-06 Bolt, Shoulder  
117 532 17 48-73 Gauge Wheel  
120 819 13 20-12 Washer 13/32 x 1-1/4 x 12 Ga.  
122 532 18 75-57 Bushing Tension Relief  
185 873 90 07-00 Nut Lock Flange 7/16-14 Gr. 5  
187 532 19 51-61 Stud Fastener w/"D" Anti-Rotation  
188 873 90 05-00 Nut Lock Hex Flange 5/16-18  
189 532 19 51-85 Arm Susp. Mower Rear  
190 532 19 65-39 Bolt Shoulder  
532 11 04-85 Bearing, Ball, Mandrel  
872 14 05-05 Bolt Carriage 5/16-18 x 5/8  
532 19 42-08 Pin Cotter 5/16 Bowtie  
873 68 05-00 Nut, Crownlock 5/16-18 unc  
532 10 53-04 Cap Sleeve  
532 17 81-02 Spring, Torsion  
532 11 04-52 Nut, Push  
192 532 19 84-68 Keeper Belt Idler  
532 18 89-38 Deflector Shield  
194 874 49 07-36 Bolt Hex Washer Head 7/16-24  
196 872 14 06-20 Bolt Rdhd 3/8-16 x 2-1/2 Gr. 5  
241 532 15 29-27 Screw TT #10-32.5. 3/8 Flange  
242 532 41 55-98 Port Washout  
532 13 14-91 Rod, Hinge  
532 17 39-84 Screw, Thdroll Washer Head  
532 18 76-90 Washer, Spacer Mower Vented  
532 15 35-35 Pulley, Mandrel  
- -  
532 18 72-92 Mandrel Asm. Service Mandre-  
lAssembly (Includes housing,  
532 40 02-34 Nut, Flg. Top Lock  
873 68 06-00 Nut Crownlock 3/8-16 unc  
532 19 73-80 Pulley, Idler, 4.50  
532 19 60-65 Arm, Idler  
532 13 77-29 Screw, Thdroll. 1/4-20 x 5/8  
532 19 61-03 Belt Deck Drive  
shaft assembly, and bearing only  
- pulley/nut/washer and blade  
bolt/washers not included)  
- -  
532 19 93-00 Replacement Mower, Complete  
873 90 06-00 Nut, Lock Flg. 3/8-16 unc  
872 11 06-16 Bolt Rdhd Sqnk 3/8-16 unc x 2  
532 19 73-79 Pulley Idler  
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
532 18 73-42 Baffle Right  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRACTOR - - MODEL NUMBER YTH26V54 (96043013200), PRODUCT NO. 960 43 01-32  
DECALS  
2
11  
10  
5
2
6
3
1
9
4
8
7
12  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
10  
11  
12  
- -  
- -  
- -  
- -  
- -  
532 42 41-02 Decal, Warning Spark Arrestor  
532 43 63-90 Decal, Label  
1
2
3
4
5
6
7
8
9
532 41 16-57 Decal, Operators  
532 42 91-96 Decal, Badge  
532 44 05-69 Decal, Panel SD  
532 43 50-97 Decal, Eng. HP  
532 42 38-29 Decal, Customer Respons.  
532 44 13-10 Decal, Replacement  
532 17 05-63 Decal, Mower Caution  
532 17 84-55 Decal, Mower Caution  
532 14 50-05 Decal, Battery Dnge/Poi  
532 19 87-85 Decal, Mower V-Belt Schematic  
532 16 69-60 Decal, Bypass  
532 43 96-81 Pad, Footrest, LH  
532 43 96-82 Pad, Footrest, RH  
532 44 11-32 Manual, Owner's (English)  
532 44 11-33 Manual, Owner's (Spanish)  
KEY  
NO.  
PART  
NO.  
WHEELS AND TIRES  
DESCRIPTION  
1
532 05 91-92 Cap Valve Tire  
2
532 06 51-39 Stem Valve  
3
532 13 83-36 Rim Front Service  
1
4
532 05 99-04 Tube Front (Service Item Only)  
532 10 62-22 Tire TM Front 15 x 6.00-6  
532 12 49-57 Fitting Grease (Front Wheel Only)  
532 12 49-59 Bearing Flange (Front Wheel Only)  
532 17 50-39 Cap Axle Blk 1 50 x 1 00  
532 13 84-68 Tire TM Rear 30 x 10.00-8  
532 12 49-26 Tube Rear (Service Item Only)  
532 13 83-37 Rim Asm 8" rear Service  
532 14 43-34 Sealant, Tire (10 oz. Tube)  
11  
2
3
5
6
4
7
10  
7
8
9
5
9
10  
11  
- -  
6
8
NOTE: All component dimensions given in U.S. inches  
1 inch = 25.4 mm  
wheel_art_1-tex  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
&RQVXPHUꢀ:KHHOHGꢀ3URGXFWVꢀ±ꢀ/LPLWHGꢀ:DUUDQW\ꢀ  
+XVTYDUQDꢀZDUUDQWVꢀWRꢀWKHꢀRULJLQDOꢀUHWDLOꢀSXUFKDVHUꢀWKDWꢀWKLVꢀ+XVTYDUQDŠꢀSURGXFWꢀLVꢀIUHHꢀIURPꢀGHIHFWVꢀLQꢀPDWHULDOꢀRUꢀZRUNPDQVKLS  
XQGHUꢀQRUPDOꢀXVHꢀDQGꢀPDLQWHQDQFHꢀIURPꢀWKHꢀGDWHꢀRIꢀUHWDLOꢀSXUFKDVHꢀIRUꢀWKHꢀDSSOLFDEOHꢀ:DUUDQW\ꢀ3HULRGꢀVKRZQꢀRQꢀ([KLELWꢀ$ꢁꢀꢀ&HUWDLQꢀ  
FRPSRQHQWVꢀꢂHꢁJꢁꢃꢀHQJLQHVꢀDQGꢀWUDQVPLVVLRQVꢄꢀDUHꢀH[FOXGHGꢀIURPꢀFRYHUDJHꢃꢀDQGꢀRWKHUꢀOLPLWDWLRQVꢀDSSO\ꢃꢀDVꢀGHVFULEHGꢀLQꢀWKLVꢀGRFXPHQWꢁꢀꢀꢀ  
+XVTYDUQDꢀZLOOꢀUHSDLUꢀRUꢀUHSODFHꢀDWꢀLWVꢀGLVFUHWLRQꢃꢀDQ\ꢀGHIHFWLYHꢀSURGXFWꢀRUꢀSDUWꢀFRYHUHGꢀE\ꢀWKHꢀ/LPLWHGꢀ:DUUDQW\ꢃꢀIUHHꢀRIꢀFKDUJHꢀDWꢀDQ\ꢀ  
DXWKRUL]HGꢀ +XVTYDUQDꢀ 6HUYLFLQJꢀ 'HDOHUꢅ&HQWHUꢀ XVLQJꢀ RULJLQDOꢀ 2(0ꢀ +XVTYDUQDꢀ UHSODFHPHQWꢀ SDUWVꢃꢀ VXEMHFWꢀ WRꢀ WKHꢀ OLPLWDWLRQVꢀ DQGꢀ  
H[FOXVLRQVꢀGHVFULEHGꢀEHORZꢁꢀꢀ+XVTYDUQDꢀGRHVꢀQRWꢀRIIHUꢀDQꢀRYHUꢆWKHꢆFRXQWHUꢀH[FKDQJHꢀSURJUDPꢁꢀ  
7+,6ꢀ /,0,7('ꢀ :$55$17<ꢀ ,6ꢀ 7+(ꢀ 62/(ꢀ (;35(66ꢀ :$55$17<ꢀ 3529,'('ꢀ %<ꢀ +8649$51$ꢁꢀ ꢀ $1<ꢀ :$55$17<ꢀ  
7+$7ꢀ 0$<ꢀ %(ꢀ ,03/,('ꢀ %<ꢀ /$:ꢀ ꢂ,1&/8',1*ꢀ $1<ꢀ ,03/,('ꢀ :$55$17<ꢀ 2)ꢀ ),71(66ꢀ )25ꢀ $ꢀ 3$57,&8/$5ꢀ  
385326(ꢀ 25ꢀ 86(ꢀ $1'ꢀ ,03/,('ꢀ :$55$17<ꢀ 2)ꢀ 0(5&+$17$%,/,7<ꢄꢀ ,6ꢀ /,0,7('ꢀ 72ꢀ 7+(ꢀ '85$7,21ꢀ 2)ꢀ 7+(ꢀ  
$33/,&$%/(ꢀ :$55$17<ꢀ 3(5,2'ꢀ 81'(5ꢀ 7+,6ꢀ /,0,7('ꢀ :$55$17<ꢁꢀ 7+,6ꢀ /,0,7('ꢀ :$55$17<ꢀ 0$<ꢀ %(ꢀ  
02',),('ꢀ 21/<ꢀ %<ꢀ +8649$51$ꢁꢀ ꢀ 620(ꢀ 67$7(6ꢀ '2ꢀ 127ꢀ $//2:ꢀ /,0,7$7,216ꢀ 21ꢀ +2:ꢀ /21*ꢀ $1ꢀ ,03/,('ꢀ  
:$55$17<ꢀ/$676ꢃꢀ62ꢀ7+(ꢀ$%29(ꢀ/,0,7$7,216ꢀ0$<ꢀ127ꢀ$33/<ꢀ72ꢀ<28ꢁꢀ7+,6ꢀ/,0,7('ꢀ:$55$17<ꢀ*,9(6ꢀ  
<28ꢀ63(&,),&ꢀ/(*$/ꢀ5,*+76ꢃꢀ$1'ꢀ<28ꢀ0$<ꢀ$/62ꢀ+$9(ꢀ27+(5ꢀ5,*+76ꢀ:+,&+ꢀ9$5<ꢀ)520ꢀ67$7(ꢀ72ꢀ67$7(ꢁꢀ  
7+,6ꢀ:$55$17<ꢀ,6ꢀ*,9(1ꢀ21/<ꢀ%<ꢀ+8649$51$ꢁꢀꢀꢀ7+(ꢀ$%29(ꢀ5(0(',(6ꢀ$5(ꢀ7+(ꢀ(;&/86,9(ꢀ5(0(',(6ꢀ)25ꢀ  
$1<ꢀ %5($&+ꢀ 2)ꢀ 7+,6ꢀ /,0,7('ꢀ :$55$17<ꢁꢀ ꢀ +8649$51$ꢀ $1'ꢀ ,76ꢀ $)),/,$7('ꢀ &203$1,(6ꢀ 6+$//ꢀ 127ꢀ %(ꢀ  
/,$%/(ꢀ)25ꢀ$1<ꢀ63(&,$/ꢃꢀ,1&,'(17$/ꢀ25ꢀ&216(48(17,$/ꢀ'$0$*(ꢃꢀ,1&/8',1*ꢀ/267ꢀ352),76ꢀ5(68/7,1*ꢀ  
)520ꢀ$1<ꢀ68&+ꢀ%5($&+ꢃꢀ$1'ꢀ$//ꢀ68&+ꢀ'$0$*(6ꢀ$5(ꢀ+(5(%<ꢀ',6&/$,0('ꢁꢀꢀ620(ꢀ67$7(6ꢀ'2ꢀ127ꢀ$//2:ꢀ  
7+(ꢀ(;&/86,21ꢀ25ꢀ/,0,7$7,21ꢀ2)ꢀ,1&,'(17$/ꢀ25ꢀ&216(48(17,$/ꢀ'$0$*(6ꢃꢀ62ꢀ7+(ꢀ$%29(ꢀ/,0,7$7,216ꢀ  
0$<ꢀ127ꢀ$33/<ꢀ72ꢀ<28ꢁꢀ  
/,0,7$7,216ꢀ$1'ꢀ(;&/86,216ꢀ  
ꢇꢁ (QJLQHVꢁꢀ7UDQVPLVVLRQVꢀDQGꢀFHUWDLQꢀRWKHUꢀFRPSRQHQWVꢀDUHꢀ127ꢀFRYHUHGꢂ 7KLVꢀ/LPLWHGꢀ:DUUDQW\ꢀGRHVꢀQRWꢀFRYHUꢀDQ\ꢀRIꢀWKHꢀ  
IROORZLQJꢈꢀ  
ꢂDꢄ (QJLQHVꢀDQGꢀ$WWDFKPHQWVꢁꢀ([FHSWꢀZKHUHꢀRWKHUZLVHꢀLQGLFDWHGꢀRQꢀ([KLELWꢀ$ꢃꢀDOOꢀ(QJLQHVꢀDQGꢀ$WWDFKPHQWVꢀDUHꢀQRWꢀFRYHUHGꢀE\ꢀ  
WKLVꢀZDUUDQW\ꢁꢀꢀ,QꢀPRVWꢀFDVHVꢃꢀWKHVHꢀLWHPVꢀDUHꢀ127ꢀPDQXIDFWXUHGꢀE\ꢀ+XVTYDUQDꢀLQꢀZKLFKꢀFDVHꢀWKH\ꢀPD\ꢀEHꢀFRYHUHGꢀVHSDUDWHO\ꢀE\ꢀ  
WKHLUꢀUHVSHFWLYHꢀPDQXIDFWXUHU¶VꢀZDUUDQWLHVꢀLIꢀRQHꢀLVꢀSURYLGHGꢀDQGꢀLQFOXGHGꢀZLWKꢀWKHꢀSURGXFWꢀDWꢀWKHꢀWLPHꢀRIꢀSXUFKDVHꢁꢀꢀ$OOꢀVXFKꢀ  
FODLPVꢀ PXVWꢀ EHꢀ VXEPLWWHGꢀ DQGꢀ VHQWꢀ WRꢀ WKHꢀ DSSURSULDWHꢀ PDQXIDFWXUHUꢀ RUꢀ DVꢀ RWKHUZLVHꢀ GLUHFWHGꢀ LQꢀ WKRVHꢀ VHSDUDWHꢀ ZDUUDQWLHVꢁꢀ  
+XVTYDUQDꢀLVꢀQRWꢀDXWKRUL]HGꢀWRꢀKDQGOHꢀZDUUDQW\ꢀDGMXVWPHQWVꢀRUꢀUHSDLUVꢀRQꢀHQJLQHVꢀPDQXIDFWXUHGꢀE\ꢀ%ULJJVꢀ ꢀ6WUDWWRQꢃꢀ+RQGDꢃꢀ  
.DZDVDNLꢃꢀRUꢀ.RKOHUꢀꢂH[FHSWLRQꢀ±ꢀPRGHOVꢀHTXLSSHGꢀZLWKꢀ/&7ꢀHQJLQHVꢄꢁꢀ+XVTYDUQDꢀGRHVꢀQRWꢀDVVXPHꢀDQ\ꢀZDUUDQW\ꢀREOLJDWLRQꢀRIꢀ  
WKHꢀRWKHUꢀPDQXIDFWXUHU¶VꢀHQJLQHVꢁ  
ꢂEꢄ 7UDQVPLVVLRQVꢁꢀꢀ([FHSWꢀZKHUHꢀRWKHUZLVHꢀLQGLFDWHGꢀRQꢀ([KLELWꢀ$ꢃꢀ7UDQVPLVVLRQꢀꢅꢀ7UDQVD[OHꢀꢂLQFOXGLQJꢀ'ULYHꢀ6\VWHPVꢄꢀDUHꢀQRWꢀ  
FRYHUHGꢀE\ꢀWKLVꢀZDUUDQW\ꢁꢀꢀ,QꢀPRVWꢀFDVHVꢃꢀWKHVHꢀLWHPVꢀDUHꢀ127ꢀPDQXIDFWXUHGꢀE\ꢀ+XVTYDUQDꢀLQꢀZKLFKꢀFDVHꢀWKH\ꢀPD\ꢀEHꢀFRYHUHGꢀ  
VHSDUDWHO\ꢀE\ꢀWKHLUꢀUHVSHFWLYHꢀPDQXIDFWXUHU¶VꢀZDUUDQWLHVꢀLIꢀRQHꢀLVꢀSURYLGHGꢀDQGꢀLQFOXGHGꢀZLWKꢀWKHꢀSURGXFWꢀDWꢀWKHꢀWLPHꢀRIꢀSXUFKDVHꢁꢀꢀ  
7KHꢀIROORZLQJꢀWUDQVPLVVLRQꢀꢅꢀWUDQVD[OHꢀPDQXIDFWXUHUVꢃꢀ'DQDꢃꢀ+\GURꢆ*HDUꢃꢀ7XIIꢆ7RUTꢀSURYLGHꢀDꢀZDUUDQW\ꢀIRUꢀWKHꢀWUDQVPLVVLRQꢀꢅꢀ  
WUDQVD[OHꢀWRꢀWKHꢀXOWLPDWHꢀSXUFKDVHUꢀRUꢀWRꢀ+XVTYDUQDꢁꢀ+XVTYDUQDꢀZLOOꢀDVVLJQꢀWKHꢀWUDQVPLVVLRQꢀꢅꢀWUDQVD[OHꢀPDQXIDFWXUHU¶VꢀZDUUDQW\  
RUꢀDQ\ꢀULJKWVꢀWKHUHRIꢀWRꢀWKHꢀRULJLQDOꢀSXUFKDVHUꢀRIꢀWKHꢀXQLWꢁꢀ7RꢀREWDLQꢀWUDQVPLVVLRQꢀꢅꢀWUDQVD[OHꢀZDUUDQW\ꢀVHUYLFHꢃꢀILUVWꢀFRQWDFWꢀWKHꢀ  
UHWDLOHUꢀZKRꢀ\RXꢀSXUFKDVHGꢀWKHꢀXQLWꢀIURPꢁꢀ6KRXOGꢀ\RXꢀUHTXLUHꢀDVVLVWDQFHꢀRUꢀKDYHꢀDQ\ꢀTXHVWLRQVꢀFRQFHUQLQJꢀWUDQVPLVVLRQꢀꢅꢀWUDQVD[OHꢀ  
ZDUUDQW\ꢀ FRYHUDJHꢃꢀ FRQWDFWꢀ +XVTYDUQDꢀ GLUHFWO\ꢀ DWꢀ RXUꢀ ZHEVLWHꢀ ZZZꢁKXVTYDUQDꢁFRPꢀ RUꢀ FDOOꢀ ꢉꢊꢊꢆꢋꢉꢌꢆꢍꢎꢍꢇꢀ IRUꢀ DQꢀ DXWKRUL]HGꢀ  
+XVTYDUQDꢀVHUYLFHꢀSURYLGHUꢁꢀ$OOꢀVXFKꢀFODLPVꢀPXVWꢀEHꢀVXEPLWWHGꢀDQGꢀVHQWꢀWRꢀWKHꢀDSSURSULDWHꢀPDQXIDFWXUHUꢀRUꢀDVꢀRWKHUZLVHꢀGLUHFWHG  
LQꢀWKRVHꢀVHSDUDWHꢀZDUUDQWLHVꢁꢀ+XVTYDUQDꢀLVꢀQRWꢀDXWKRUL]HGꢀWRꢀKDQGOHꢀZDUUDQW\ꢀDGMXVWPHQWVꢀRUꢀUHSDLUVꢀRQꢀWUDQVPLVVLRQVꢀRUꢀWUDQVD[OHVꢁ  
+XVTYDUQDꢀGRHVꢀQRWꢀDVVXPHꢀDQ\ꢀZDUUDQW\ꢀREOLJDWLRQꢀRIꢀWKHꢀDERYHꢀOLVWHGꢀPDQXIDFWXUHUVꢀꢂIRUꢀH[FHSWLRQVꢀ±ꢀVHHꢀ([KLELWꢀ$ꢄꢁ  
ꢂFꢄ ([SHQGDEOHꢀ 3DUWVꢁꢀ ꢀ 7KLVꢀ /LPLWHGꢀ :DUUDQW\ꢀ GRHVꢀ QRWꢀ FRYHUꢀ JHQHUDOꢀ PDLQWHQDQFHꢀ SDUWVꢀ DQGꢀ LWHPVꢀ ꢂ³([SHQGDEOHꢀ 3DUWV´ꢄꢃ  
LQFOXGLQJꢀZLWKRXWꢀOLPLWDWLRQꢀVSDUNꢀSOXJVꢃꢀEXOEVꢃꢀILOWHUVꢃꢀOXEULFDQWVꢃꢀVWDUWHUꢀFRUGVꢃꢀEHOWVꢃꢀEODGHVꢃꢀDQGꢀEODGHꢀDGDSWHUVꢁꢀ  
ꢂGꢄ (PLVVLRQVꢀ&RQWUROꢀ&RPSRQHQWVꢁꢀꢀꢀ7KLVꢀ/LPLWHGꢀ:DUUDQW\ꢀGRHVꢀQRWꢀFRYHUꢀ(PLVVLRQVꢀFRQWUROꢀHTXLSPHQWꢀDQGꢀFRPSRQHQWVꢀWRꢀWKHꢀ  
H[WHQWꢀUHJXODWHGꢀE\ꢀWKHꢀ8ꢁ6ꢁꢀ(QYLURQPHQWDOꢀ3URWHFWLRQꢀ$JHQF\ꢀRUꢀVLPLODUꢀVWDWHꢀDJHQFLHVꢁꢀꢀ6XFKꢀHTXLSPHQWꢀDQGꢀFRPSRQHQWVꢀDUHꢀ  
FRYHUHGꢀE\ꢀDꢀVHSDUDWHꢀHPLVVLRQꢀFRQWUROꢀZDUUDQW\ꢀVWDWHPHQWꢀVXSSOLHGꢀZLWKꢀ\RXUꢀQHZꢀSURGXFWꢁꢀꢀ3OHDVHꢀFRQVXOWꢀWKLVꢀVHSDUDWHꢀZDUUDQW\  
VWDWHPHQWꢀIRUꢀGHWDLOVꢁꢀꢀ  
ꢏꢁ $Q\ꢀ &200(5&,$/ꢁꢀ ,16,787,21$/ꢁꢀ $*5,&8/785$/ꢁꢀ ,1'8675,$/ꢁꢀ ,1&20(ꢀ 352'8&,1*ꢁꢀ RUꢀ 5(17$/ꢀ XVHꢀ ZLOOꢀ UHVXOWꢀ LQꢀ HLWKHUꢀ 1Rꢀ  
:DUUDQW\ꢀRUꢀDꢀ6KRUWHQHGꢀ:DUUDQW\ꢀ3HULRGꢀꢀ'HSHQGLQJꢀRQꢀWKHꢀSURGXFWꢐꢀWKHUHꢀLVꢀHLWKHUꢀ12ꢀ:$55$17<ꢀRUꢀDꢀUHGXFHGꢀZDUUDQW\ꢀLIꢀWKHꢀSURGXFWꢀLVꢀXVHGꢀIRUꢀFRPPHUFLDOꢃꢀ  
LQVWLWXWLRQDOꢃꢀDJULFXOWXUDOꢃꢀLQGXVWULDOꢃꢀLQFRPHꢀSURGXFLQJꢃꢀRUꢀUHQWDOꢀSXUSRVHVꢁꢀꢀ3OHDVHꢀUHIHUꢀWRꢀ([KLELWꢀ$ꢁꢀꢀꢀ  
ꢑꢁ 2ZQHU¶Vꢀꢃ<RXUꢄꢀ5HVSRQVLELOLWLHVꢂꢀꢀ7RꢀSUHVHUYHꢀ\RXUꢀULJKWVꢀXQGHUꢀWKLVꢀ/LPLWHGꢀ:DUUDQW\ꢃꢀ\RXꢀPXVWꢀGHPRQVWUDWHꢀUHDVRQDEOHꢀFDUHꢀ  
DQGꢀXVHꢀRIꢀWKHꢀSURGXFWꢃꢀLQFOXGLQJꢃꢀIROORZLQJꢀWKHꢀSUHYHQWDWLYHꢀPDLQWHQDQFHꢃꢀVWRUDJHꢃꢀIXHOꢀDQGꢀRLOꢀXVDJHVꢀDVꢀSUHVFULEHGꢀLQꢀWKHꢀHQFORVHGꢀ  
RSHUDWRU¶VꢀPDQXDOꢁꢀꢀꢀ)RUꢀH[DPSOHꢃꢀWKHꢀIROORZLQJꢀLWHPVꢀDUHꢀWKHꢀ2ZQHU¶VꢀUHVSRQVLELOLW\ꢀDQGꢀDUHꢀQRWꢀFRYHUHGꢀE\ꢀWKLVꢀ/LPLWHGꢀ:DUUDQW\ꢈꢀ  
Dꢁ 6HWꢆXSꢀDQGꢀSUHꢆGHOLYHU\ꢀVHUYLFHꢃꢀDQGꢀHQJLQHꢀWXQHꢆXSVꢁꢀ  
Eꢁ$GMXVWPHQWVꢀDIWHUꢀWKHꢀILUVWꢀꢂꢑꢊꢄꢀWKLUW\ꢀGD\VꢀRIꢀSXUFKDVHꢀDQGꢀEH\RQGꢃꢀVXFKꢀDVꢀWKURWWOHꢀFDEOHꢃꢀEHOWꢀJXLGHVꢀDGMXVWPHQWVꢁꢀ  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fꢀ 3UHYHQWDWLYHꢁPDLQWHQDQFHꢁDVꢁRXWOLQHGꢁLQꢁWKHꢁRSHUDWRU¶VꢁPDQXDOꢀꢁ  
,QꢁDGGLWLRQꢂꢁ\RXꢁPXVWꢁFHDVHꢁXVLQJꢁWKHꢁSURGXFWꢁLPPHGLDWHO\ꢁXSRQꢁDQ\ꢁIDLOXUHꢁRUꢁGDPDJHꢀꢁ7KHꢁSURGXFWꢁVKRXOGꢁEHꢁWDNHQꢁWRꢁDQꢁDXWKRUL]HGꢁ  
+XVTYDUQDꢁVHUYLFLQJꢁGHDOHUꢁSULRUꢁWRꢁDQ\ꢁIXUWKHUꢁXVHꢀꢁ  
ꢃꢀ 'DPDJHVꢀ UHVXOWLQJꢀ IURPꢀ QRUPDOꢀ DJLQJꢁꢀ ZHDUꢀ DQGꢀ WHDUꢀ RUꢀ QHJOHFWꢀ DUHꢀ 127ꢀ FRYHUHGꢂꢀ ꢀ ꢀ 7KHꢁ /LPLWHGꢁ :DUUDQW\ꢁ GRHVꢁ QRWꢁ FRYHUꢁ  
GDPDJHꢁRWKHUꢁWKDQꢁWKDWꢁUHVXOWLQJꢁIURPꢁGHIHFWVꢁLQꢁPDWHULDOꢁRUꢁZRUNPDQVKLSꢀꢁꢁ7KHꢁIROORZLQJꢁDUHꢁ127ꢁFRQVLGHUHGꢁGHIHFWVꢁLQꢁPDWHULDOꢁ RUꢁ  
ZRUNPDQVKLSꢂꢁDQGꢁWKHUHIRUHꢁDUHꢁ127ꢁFRYHUHGꢀꢁ  
ꢄDꢅ $EUDVLRQꢁWRꢁPRZHUꢁGHFNVꢆꢁꢁ  
ꢄEꢅ 7LUHVꢁGDPDJHGꢁE\ꢁH[WHUQDOꢁSXQFWXUHVꢆꢁꢁꢁꢁ  
ꢄFꢅ 1DWXUDOꢁGLVFRORUDWLRQꢁRIꢁPDWHULDOVꢁGXHꢁWRꢁXOWUDYLROHWꢁOLJKWꢆ  
ꢄGꢅ 'DPDJHꢁWRꢁFXWWLQJꢁHTXLSPHQWꢁE\ꢁZD\ꢁRIꢁFRQWDFWꢁZLWKꢂꢁURFNVꢂꢁRUꢁRWKHUꢁQRQꢇDSSURYHGꢁPDWHULDOVꢁDQGꢈRUꢁVWUXFWXUHVꢆꢁ  
,QꢁDGGLWLRQꢂꢁWKLVꢁ/LPLWHGꢁ:DUUDQW\ꢁGRHVꢁQRWꢁFRYHUꢁGDPDJHVꢂꢁPDOIXQFWLRQVꢁRUꢁIDLOXUHVꢁUHVXOWLQJꢁIURPꢁDEXVHꢁRUꢁQHJOHFWꢁRIꢁWKHꢁSURGXFWꢁ  
UHODWHGꢁWRꢁRUꢁLQFOXGLQJꢁDQ\ꢁRIꢁWKHꢁIROORZLQJꢉꢁꢁꢁ  
ꢄHꢅ )DLOXUHꢁWRꢁSURYLGHꢁRUꢁSHUIRUPꢁUHTXLUHGꢁPDLQWHQDQFHꢁVHUYLFHVꢁDVꢁSUHVFULEHGꢁLQꢁWKHꢁRSHUDWRU¶VꢁPDQXDOꢆꢁꢁ  
ꢄIꢅ $EXVHꢂꢁPLVXVHꢂꢁQHJOHFWꢂꢁPRGLILFDWLRQVꢂꢁDOWHUDWLRQVꢂꢁQRUPDOꢁZHDUꢂꢁLPSURSHUꢁVHUYLFLQJꢂꢁXVHꢁRIꢁXQDXWKRUL]HGꢁDWWDFKPHQWVꢂꢁ/DFNꢁRIꢁꢁ  
OXEULFDWLRQꢁRUꢁHQJLQHꢁIDLOXUHꢂꢁGXHꢁWRꢁWKHꢁXVHꢁRIꢁRLOVꢁWKDWꢁGRꢁQRWꢁꢁPHHWꢁꢁ(QJLQHꢁPDQXIDFWXUHU¶VꢁVSHFLILFDWLRQVꢆꢁ  
ꢄJꢅ 8VHꢁRIꢁJDVRKROꢂꢁFRQWDLQLQJꢁPHWKDQROꢁꢄZRRGꢁDOFRKROꢅꢂꢁ*DVRKROꢁZKLFKꢁFRQWDLQVꢁDꢁPD[LPXPꢁꢊꢋꢌꢁHWKDQROꢁꢄJUDLQꢁDOFRKROꢅꢁRUꢁ  
ꢊꢍꢌꢁ07%(ꢁꢄPHWK\OꢈWHUWLDU\ꢈEXW\OꢈHWKHUꢅꢁLVꢁDSSURYHGꢆꢁ  
ꢄKꢅ 8VHꢁRIꢁHWKHUꢁRUꢁDQ\ꢁVWDUWLQJꢁIOXLGVꢆꢁꢁ  
ꢄLꢅ 3UHVVXUHꢁFOHDQLQJꢁRUꢁVWHDPꢁFOHDQLQJꢁWKHꢁSURGXFWꢆꢁ  
ꢄMꢅ 8VHꢁRIꢁVSDUNꢁSOXJVꢁRWKHUꢁWKDQꢁWKRVHꢁPHHWLQJꢁHPLVVLRQꢁSHUIRUPDQFHꢁUHTXLUHPHQWVꢁOLVWHGꢁLQꢁWKHꢁRSHUDWRU¶VꢁPDQXDOꢆꢁ  
ꢄNꢅ 7DPSHULQJꢁ ZLWKꢁ HQJLQHꢁ VSHHGꢁ JRYHUQRUꢁ RUꢁ HPLVVLRQꢁ FRPSRQHQWVꢂꢁ RUꢁ UXQQLQJꢁ HQJLQHVꢁ DERYHꢁ VSHFLILHGꢁ DQGꢁ UHFRPPHQGHGꢁ  
HQJLQHꢁVSHHGVꢁDVꢁOLVWHGꢁLQꢁ\RXUꢁRSHUDWRU¶VꢁPDQXDOꢆꢁ  
ꢄOꢅ 2SHUDWLRQꢁRIꢁWKHꢁXQLWꢁZLWKꢁLPSURSHUO\ꢁLQVWDOOHGꢈUHPRYHGꢁRUꢁPRGLILHGꢁFXWWLQJꢁVKLHOGVꢂꢁJXDUGVꢂꢁRUꢁVDIHW\ꢁGHYLFHVꢆꢁ  
ꢄPꢅ $Q\ꢁUHPRYHGꢈGDPDJHGꢁDLUꢁILOWHUꢂꢁH[FHVVLYHꢁGLUWꢂꢁDEUDVLYHVꢂꢁVDOWꢁZDWHUꢂꢁPRLVWXUHꢂꢁFRUURVLRQꢂꢁUXVWꢂꢁYDUQLVKꢂꢁVWDOHꢁIXHOꢂꢁRUꢁDQ\ꢁ  
DGYHUVHꢁUHDFWLRQꢁGXHꢁWRꢁLQFRUUHFWꢁVWRUDJHꢁSURFHGXUHVꢆꢁ  
ꢄQꢅ )DLOXUHVꢁ GXHꢁ WRꢁ LPSURSHUꢁ VHWꢁ XSꢂꢁ SUHꢇGHOLYHU\ꢁ VHUYLFHꢁ RUꢁ UHSDLUꢁ VHUYLFHꢁ E\ꢁ DQ\RQHꢁ RWKHUꢁ WKDQꢁ DQꢁ DXWKRUL]HGꢁ +XVTYDUQDꢁ  
VHUYLFLQJꢁGHDOHUꢁGXULQJꢁWKHꢁZDUUDQW\ꢁSHULRGꢆꢁ  
ꢄRꢅ 'LUWꢁ FRQWDPLQDWHGꢁ JUHDVHꢁ RUꢁ RLOꢂꢁ XVHꢁ RIꢁ LQFRUUHFWꢁ W\SHꢁ RIꢁ JUHDVHVꢁ RUꢁ RLOVꢂꢁ IDLOXUHꢁ WRꢁ FRPSO\ꢁ ZLWKꢁ UHFRPPHQGHGꢁ JUHDVLQJꢁ  
LQWHUYDOVꢂꢁZDWHUꢁRUꢁPRLVWXUHꢁGDPDJHꢂꢁDQGꢈRUꢁLPSURSHUꢁVWRUDJHꢆꢁ  
ꢄSꢅ 6SUD\HUVꢁSXPSLQJꢁRUꢁVSUD\LQJꢁFDXVWLFꢁRUꢁIODPPDEOHꢁPDWHULDOVꢂꢁODFNꢁRIꢁRUꢁEURNHQꢁVWUDLQHUVꢆꢁRUꢁ  
ꢄTꢅ &RQWLQXHGꢁXVHꢁRIꢁSURGXFWꢂꢁDIWHUꢁLQLWLDOꢁRSHUDWLRQDOꢁSUREOHPꢁRUꢁIDLOXUHꢁRFFXUVꢀꢁ  
+2:ꢀ72ꢀ2%7$,1ꢀ6(59,&(  
ꢍꢀ $XWKRUL]HGꢀ +XVTYDUQDꢀ 6HUYLFLQJꢀ 'HDOHUꢃ&HQWHUꢂꢁ ꢁ ꢁ ,Qꢁ RUGHUꢁ WRꢁ REWDLQꢁ ZDUUDQW\ꢁ FRYHUDJHꢁ LWꢁ LVꢁ \RXUꢁ UHVSRQVLELOLW\ꢁ ꢁ ꢄDWꢁ \RXUꢁ  
H[SHQVHꢅꢁWRꢁGHOLYHUꢁRUꢁVKLSꢁ\RXUꢁ+XVTYDUQDꢁXQLWꢁWRꢁDQꢁDXWKRUL]HGꢁ+XVTYDUQDꢁ6HUYLFLQJꢁ'HDOHUꢈ&HQWHUꢁDQGꢁDUUDQJHꢁIRUꢁSLFNꢇXSꢁRUꢁUHWXUQ  
RIꢁ\RXUꢁXQLWꢁDIWHUꢁWKHꢁUHSDLUVꢁKDYHꢁEHHQꢁPDGHꢀꢁꢁ,Iꢁ\RXꢁGRꢁQRWꢁNQRZꢁWKHꢁORFDWLRQꢁRIꢁ\RXUꢁQHDUHVWꢁDXWKRUL]HGꢁ+XVTYDUQDꢁ6HUYLFLQJꢁ'HDOHUꢂꢁꢁ  
FDOOꢁ+XVTYDUQDꢂꢁDWꢁꢊꢇꢎꢋꢋꢇꢃꢎꢏꢇꢍꢐꢍꢊꢁGXULQJꢁWKHꢁKRXUVꢁRIꢁꢎꢉꢋꢋꢁ$0ꢁWRꢁꢎꢉꢋꢋꢁ30ꢁ(DVWHUQꢁ6WDQGDUGꢁ7LPHꢂꢁRUꢁYLVLWꢁZZZꢀKXVTYDUQDꢀFRPꢀ  
6KRXOGꢁ\RXꢁUHTXLUHꢁDVVLVWDQFHꢁRUꢁKDYHꢁTXHVWLRQVꢁFRQFHUQLQJꢁWKLVꢁ/LPLWHGꢁ:DUUDQW\ꢂꢁ\RXꢁPD\ꢁFRQWDFWꢁXVꢁDWꢁꢁꢎꢋꢋꢇꢃꢎꢏꢇꢍꢐꢍꢊꢁꢁGXULQJꢁWKH  
KRXUVꢁRIꢁꢁꢎꢉꢋꢋꢁ$0ꢁWRꢁꢎꢉꢋꢋꢁ30ꢁ(DVWHUQꢁ6WDQGDUGꢁ7LPHꢁRUꢁFRQWDFWꢁXVꢁWKURXJKꢁWKHꢁZHEꢁDWꢁZZZꢀKXVTYDUQDꢀFRPꢀ  
ꢑꢀ 'RFXPHQWDWLRQꢀ5HTXLUHGꢂꢁꢁꢁ<RXꢁPXVWꢁPDLQWDLQꢁDQGꢁSUHVHQWꢁ3URRIꢁRIꢁSXUFKDVHꢁꢄLQFOXGLQJꢁGDWHꢂꢁSURGXFWꢁPRGHOꢁDQGꢂꢁLIꢁDSSOLFDEOHꢂꢁ  
HQJLQHꢁ VHULDOꢁ QXPEHUꢅꢁ WRꢁ DQꢁ DXWKRUL]HGꢁ +XVTYDUQDꢁ 6HUYLFLQJꢁ 'HDOHUꢁ IRUꢁ ZDUUDQW\ꢁ VHUYLFHꢁ XQGHUꢁ WKLVꢁ /LPLWHGꢁ :DUUDQW\ꢀꢁ ꢁ 3URRIꢁ RIꢁ  
SXUFKDVHꢁ UHVWVꢁ VROHO\ꢁ ZLWKꢁ WKHꢁ RZQHUꢇFXVWRPHUꢀꢁ ꢁ ꢁ +XVTYDUQDꢁ HQFRXUDJHVꢁ \RXꢁ WRꢁ UHJLVWHUꢁ \RXUꢁ SURGXFWꢁ RQOLQHꢁ DWꢁ  
ZZZꢀXVDꢀKXVTYDUQDꢀFRPꢁWRꢁKHOSꢁHQVXUHꢂꢁDPRQJꢁRWKHUꢁWKLQJVꢂꢁWKDWꢁ\RXꢁFDQꢁEHꢁQRWLILHGꢁRIꢁLPSRUWDQWꢁSURGXFWꢁLQIRUPDWLRQꢀꢁꢁ+RZHYHUꢂꢁ  
UHJLVWHULQJꢁ\RXUꢁSURGXFWꢁLVꢁQRWꢁDꢁFRQGLWLRQꢁRIꢁZDUUDQW\ꢁVHUYLFHꢀꢁꢁꢁ  
+XVTYDUQDꢀ&RQVXPHUꢀ2XWGRRUꢀ3URGXFWVꢀ1ꢁ$ꢁꢂꢀ,QFꢁꢃꢀ+XVTYDUQDꢀ3URIHVVLRQDOꢀ3URGXFWVꢂꢀ,QFꢁꢀ  
ꢄꢅꢅꢆꢀ+DUULVꢀ&RUQHUVꢀ3DUNZD\ꢀ&KDUORWWHꢂꢀ1&ꢀꢇꢈꢇꢉꢄꢀ  
ꢁ
ꢁ
ꢍꢏꢍꢁꢃꢐꢁꢃꢒꢇꢋꢊꢁ5ꢒꢁꢁꢓꢋꢊꢋꢁ  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
&RQVXPHUꢀ:KHHOHGꢀ:DUUDQW\ꢀ&KDUWꢀꢁꢂꢃꢂ  
([KLELWꢀ$  
&RQVXPHUꢀ ꢀSHUVRQDOꢁ  
&RPPHUFLDO ꢀDQ\ꢂFRPPHUFLDOꢁꢂ 5HQWDOꢀ ꢀDQ\ꢂUHQWDOꢂ  
KRXVHKROGꢂXVHꢂRQO\ꢃ  
SURIHVVLRQDOꢁꢂLQVWLWXWLRQDOꢁꢂ  
DULJFXOXWUDOꢁꢂRUꢂLQFRPHꢂSURGXFLQJꢂ  
XVHꢁꢂRWKHUꢂWKDQꢂ5HQWDOꢂ8VHꢃ  
XVDJHꢃ  
3URGXFWꢄ&RPSRQHQW  
5LGLQJꢂ/DZQꢂ7UDFWRUVꢄ  
)UDPHꢁꢀ&KDVVLVꢁꢀ)URQWꢀ$[OH  
(QJLQHꢃ  
ꢂꢀ<HDUV  
ꢀꢃ  
12ꢀ:$55$17<  
ꢀꢃ  
12ꢀ:$55$17<  
ꢀꢃ  
7UDQVPLVVLRQꢀꢄLIꢀPDGHꢀE\ꢀ  
+XVTYDUQDꢅ3HHUOHVVꢆ  
7UDQVPLVVLRQꢀꢄLIꢀWKLUGꢀSDUW\ꢆꢃꢃ  
%DWWHU\  
ꢇꢀ<HDUVꢀ  
ꢀꢀꢃꢃ  
ꢈꢀ<HDUꢀ3URꢉUDWHG  
ꢇꢀ<HDUVꢀ  
12ꢀ:$55$17<  
ꢀꢀꢃꢃ  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
ꢀꢀꢃꢃ  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
2WKHUꢀ1RQꢉ([SHQGDEOHꢀ&RPSRQHQWV  
5HVLGHQWLDOꢂ=HURꢂ7XUQꢂ0RZHUVꢂꢀ 5=ꢀ2QO\ ꢃ  
(QJLQHꢃ  
7UDQVPLVVLRQꢀꢃꢃ  
%DWWHU\  
2WKHUꢀ1RQꢉ([SHQGDEOHꢀ&RPSRQHQWV  
5HVLGHQWLDOꢂ=HURꢂ7XUQꢂ0RZHUVꢂꢀ 0=ꢀ ꢀ(= ꢃ  
(QJLQHꢃ  
ꢀꢃ  
ꢀꢀꢃꢃ  
ꢀꢃ  
ꢀꢃ  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
ꢈꢀ<HDUꢀ3URꢉUDWHG  
ꢇꢀ<HDUVꢀ  
ꢀꢃ  
ꢀꢃꢃ  
ꢀꢃ  
ꢀꢃꢃ  
ꢀꢃ  
ꢀꢃꢃ  
7UDQVPLVVLRQꢀꢃꢃ  
%DWWHU\  
ꢈꢀ<HDUꢀ3URꢉUDWHG  
ꢇꢀ<HDUVꢀ  
ꢈꢀ<HDUꢀ3URꢉUDWHG  
ꢈꢀ<HDU  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
2WKHUꢀ1RQꢉ([SHQGDEOHꢀ&RPSRQHQWV  
/(ꢅꢆꢇꢂ(GJHU  
(QJLQHꢃ  
ꢀꢀꢃ  
ꢀꢀꢃ  
ꢀꢀꢃ  
2WKHUꢀ1RQꢉ([SHQGDEOHꢀ&RPSRQHQWV  
:DONꢂ%HKLQGꢂ0RZHUV  
(QJLQHꢃ  
ꢊꢀ<HDUV  
ꢋꢌꢀGD\V  
ꢋꢌꢀGD\V  
ꢀꢃ  
ꢀꢃ  
ꢀꢃ  
%DWWHU\  
ꢈꢀ<HDUꢀ3URꢉUDWHG  
ꢊꢀ<HDUV  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
2WKHUꢀ1RQꢉ([SHQGDEOHꢀ&RPSRQHQWV  
6QRZꢂ7KURZHUV  
(QJLQHꢃ  
ꢃ
ꢃ
ꢃ
2WKHUꢀ1RQꢉ([SHQGDEOHꢀ&RPSRQHQWV  
ꢊꢀ<HDUV  
ꢋꢌꢀGD\V  
ꢋꢌꢀGD\V  
7LOOHUV  
(QJLQHꢃ  
%DWWHU\  
ꢀꢃ  
ꢈꢀ<HDUꢀ3URꢉUDWHG  
ꢊꢀ<HDUV  
ꢀꢃ  
ꢀꢃ  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
2WKHUꢀ1RQꢉ([SHQGDEOHꢀ&RPSRQHQWV  
7LOOHUꢀ7LQHV  
ꢃꢃꢃ  
+RYHULQJꢂ7ULPPHUV  
(QJLQHꢃ  
ꢀꢀꢃ  
ꢀꢀꢃ  
ꢀꢀꢃ  
2WKHUꢀ1RQꢉ([SHQGDEOHꢀ&RPSRQHQWV  
ꢊꢀ<HDUV  
&RQVXPHU  
ꢈꢀ<HDU  
&RPPHUFLDO  
ꢋꢌꢀGD\V  
5HQWDO  
ꢃꢀ6HHꢀ6HSDUDWHꢀ(QJLQHꢀ0DQXIDFWXUHUꢍVꢀꢀRUꢀ0DQXIDFWXUHUꢍVꢀZDUUDQW\  
/&7ꢀ(QJLQHVꢀRQꢀVSHFLILFꢀ6QRZꢀ7KURZHUVꢀ ꢀ7LOOHUVꢁꢀZDUUDQW\ꢀWKURXJKꢀ+XVTYDUQDꢎ  
ꢃꢃꢀ6HHꢀUHIHUHQFHꢀꢈꢀꢄEꢆꢀRIꢀWKHꢀZDUUDQW\ꢀVWDWHPHQWꢎ  
5=ꢀꢉꢀ7ZRꢀꢄꢊꢆꢀ<HDUꢀ&RQVXPHUꢀZDUUDQW\ꢁꢀSDUWVꢀ ꢀODERUꢁꢀZLWKꢀ+\GURꢉ*HDUꢀ'LVWULEXWRUꢀQHWZRUNꢎ  
(=ꢀꢅꢀ2QHꢀꢆꢃꢇꢀ<HDUꢀ&RPPHUFLDOꢀZDUUDQW\ꢈꢀSDUWVꢀ ꢀODERUꢈꢀZLWKꢀ+XVTYDUQDꢉꢀ  
ꢀꢀꢀꢀꢀꢀꢀ7ZRꢀꢄꢊꢆꢀ<HDUꢀ&RQVXPHUꢀZDUUDQW\ꢁꢀSDUWVꢀ ꢀODERUꢁꢀZLWKꢀ+\GURꢉ*HDUꢀ'LVWULEXWRUꢀQHWZRUNꢎ  
0=ꢀꢉꢀ7ZRꢀꢄꢊꢆꢀ<HDUꢀ&RPPHUFLDOꢀZDUUDQW\ꢁꢀSDUWVꢀ ꢀODERUꢁꢀZLWKꢀ+\GURꢉ*HDUꢀ'LVWULEXWRUꢀQHWZRUNꢎꢀꢀ  
ꢃꢃꢃꢀꢏ/LPLWHGꢀ/LIHWLPHꢀ:DUUDQW\ꢏꢀRQꢀ7LOOHUꢀWLQHVꢀLVꢀIRUꢀWKHꢀOLIHꢀRIꢀWKHꢀSURGXFWꢀRUꢀꢐꢀꢄVHYHQꢆꢀ\HDUVꢀDIWHUꢀWKHꢀODVWꢀGDWHꢀRIꢀWKHꢀFRPSOHWH  
XQLWꢍVꢀILQDOꢀSURGXFWLRQꢁꢀZKLFKHYHUꢀFRPHVꢀILUVWꢎ  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
&RQVXPHUꢀ:KHHOHGꢀ:DUUDQW\ꢀ&KDUWꢀꢁꢂꢃꢂ  
([KLELWꢀ$  
&RQVXPHUꢀ ꢀSHUVRQDOꢁ  
&RPPHUFLDO ꢀDQ\ꢂFRPPHUFLDOꢁꢂ 5HQWDOꢀ ꢀDQ\ꢂUHQWDOꢂ  
KRXVHKROGꢂXVHꢂRQO\ꢃ  
SURIHVVLRQDOꢁꢂLQVWLWXWLRQDOꢁꢂ  
DULJFXOXWUDOꢁꢂRUꢂLQFRPHꢂSURGXFLQJꢂ  
XVHꢁꢂRWKHUꢂWKDQꢂ5HQWDOꢂ8VHꢃ  
XVDJHꢃ  
3URGXFWꢄ&RPSRQHQW  
)URQWꢂ0RXQWHGꢂ'HFNꢂ5LGHUV  
(QJLQHꢁ  
ꢀꢀꢁ  
ꢀꢀꢁ  
ꢀꢀꢁ  
7UDQVPLVVLRQ  
%DWWHU\  
2WKHUꢀ1RQꢄ([SHQGDEOHꢀ&RPSRQHQWV  
&XOWLYDWRUV  
ꢂꢀ<HDUV  
ꢃꢀ<HDUꢀ3URꢄUDWHG  
ꢂꢀ<HDUV  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
%DWWHU\  
ꢃꢀ<HDUꢀ3URꢄUDWHG  
ꢂꢀ<HDUV  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
2WKHUꢀ1RQꢄ([SHQGDEOHꢀ&RPSRQHQWV  
3UHVVXUHꢂ:DVKHUV  
0RGHOꢀꢅꢅꢂꢅ3:ꢆ  
ꢀꢀꢀꢀꢀ(QJLQHꢁ  
ꢀꢀꢁ  
ꢀꢀꢁ  
ꢀꢀꢁ  
ꢀꢀꢀꢀꢀ3XPS  
ꢂꢀ<HDUV  
ꢂꢀ<HDUV  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
ꢀꢀꢀꢀꢀ2WKHUꢀ1RQꢄ([SHQGDEOHꢀ&RPSRQHQWV  
$OOꢂRWKHUꢂ3UHVVXUHꢂ:DVKHUVꢂꢀꢄꢅꢆꢇ3:ꢁꢂꢈꢅꢉꢆ3:ꢁꢂꢊꢉꢋꢅ3:ꢃ  
ꢀꢀꢀꢀꢀ(QJLQHꢁ  
ꢀꢀꢁ  
ꢀꢀꢁ  
ꢀꢀꢁ  
ꢀꢀꢀꢀꢀ3XPS  
ꢂꢀ<HDUV  
ꢂꢀ<HDUV  
ꢂꢀ<HDUV  
ꢂꢀ<HDUV  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
ꢀꢀꢀꢀꢀ2WKHUꢀ1RQꢄ([SHQGDEOHꢀ&RPSRQHQWV  
*HQHUDWRUV  
(QJLQHꢁ  
ꢀꢀꢁ  
ꢀꢀꢁ  
ꢀꢀꢁ  
ꢁꢂꢀ<HDUVꢀꢇꢂQGꢀ<HDUꢀ  
3DUWVꢀ2QO\ꢈ  
ꢁꢂꢀ<HDUVꢄꢃꢉꢊꢅ*1ꢀꢀꢇꢂQGꢀ<HDUꢀ  
3DUWVꢀ2QO\ꢈ  
2WKHUꢀ1RQꢄ([SHQGDEOHꢀ&RPSRQHQWVꢁ  
6SUHDGHUV  
12ꢀ:$55$17<  
ꢃꢀ<HDU  
6SUHDGHU  
ꢃꢀ<HDU  
ꢃꢀ<HDU  
5RERWLFꢂ0RZHUV  
5RERWLFꢀ0RZHU  
%DWWHU\  
ꢂꢀ<HDUV  
ꢃꢀ<HDU  
ꢋꢌꢀGD\V  
ꢃꢀ<HDU  
ꢋꢌꢀGD\V  
ꢃꢀ<HDU  
3DUWVꢂ ꢂ$FFHVVRULHVꢂꢀLIꢂSXUFKDVHGꢃ  
$FFHVVRULHVꢀꢇHꢍJꢍꢎꢀJUDVVꢀFDWFKHUꢎꢀEXPSHUꢀ  
JXDUGꢀDFFHVVRULHVꢎꢀHWFꢍ  
3DUWVꢀꢇHꢍJꢍꢎꢀEHOWVꢎꢀEODGHVꢎꢀHWFꢍꢈ  
ꢃꢀ<HDU  
ꢉꢌꢀGD\V  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
12ꢀ:$55$17<  
3DUWVꢂ ꢂ$FFHVVRULHVꢂꢀLIꢂUHSODFHGꢂLQꢂ:DUUDQW\ꢂ6HUYLFHꢃ  
5HSODFHPHQWꢀSDUWVꢀDQGꢏRUꢀDFFHVVRULHVꢀ  
SURYLGHGꢀXQGHUꢀWKLVꢀ/LPLWHGꢀ:DUUDQW\ꢀDUHꢀ  
ZDUUDQWHGꢀRQO\ꢀIRUꢀWKHꢀ%$/$1&(ꢀRIꢀWKHꢀ  
ZDUUDQW\ꢀSHULRGꢀDSSOLFDEOHꢀWRꢀWKHꢀSDUWꢀRUꢀ  
DFFHVVRU\ꢀWKDWꢀZDVꢀUHSODFHGꢍ  
6HHꢀWRꢀOHIW  
6HHꢀWRꢀOHIW  
6HHꢀWRꢀOHIW  
&RQVXPHU  
&RPPHUFLDO  
5HQWDO  
ꢁꢀ6HHꢀ6HSDUDWHꢀ(QJLQHꢀ0DQXIDFWXUHUꢐVꢀꢀRUꢀ0DQXIDFWXUHUꢐVꢀZDUUDQW\  
/&7ꢀ(QJLQHVꢀRQꢀVSHFLILFꢀ6QRZꢀ7KURZHUVꢀ ꢀ7LOOHUVꢎꢀZDUUDQW\ꢀWKURXJKꢀ+XVTYDUQDꢍꢀ  
ꢁꢁꢀ6HHꢀUHIHUHQFHꢀꢃꢀꢇEꢈꢀRIꢀWKHꢀZDUUDQW\ꢀVWDWHPHQWꢍ  
5=ꢀꢄꢀ7ZRꢀꢇꢂꢈꢀ<HDUꢀ&RQVXPHUꢀZDUUDQW\ꢎꢀSDUWVꢀ ꢀODERUꢎꢀZLWKꢀ+\GURꢄ*HDUꢀ'LVWULEXWRUꢀQHWZRUNꢍ  
(=ꢀꢅꢀ2QHꢀꢆꢃꢇꢀ<HDUꢀ&RPPHUFLDOꢀZDUUDQW\ꢈꢀSDUWVꢀ ꢀODERUꢈꢀZLWKꢀ+XVTYDUQDꢉꢀ  
ꢀꢀꢀꢀꢀꢀꢀ7ZRꢀꢇꢂꢈꢀ<HDUꢀ&RQVXPHUꢀZDUUDQW\ꢎꢀSDUWVꢀ ꢀODERUꢎꢀZLWKꢀ+\GURꢄ*HDUꢀ'LVWULEXWRUꢀQHWZRUNꢍ  
0=ꢀꢄꢀ7ZRꢀꢇꢂꢈꢀ<HDUꢀ&RPPHUFLDOꢀZDUUDQW\ꢎꢀSDUWVꢀ ꢀODERUꢎꢀZLWKꢀ+\GURꢄ*HDUꢀ'LVWULEXWRUꢀQHWZRUNꢍꢀꢀ  
ꢁꢁꢁꢀꢑ/LPLWHGꢀ/LIHWLPHꢀ:DUUDQW\ꢑꢀRQꢀ7LOOHUꢀWLQHVꢀLVꢀIRUꢀWKHꢀOLIHꢀRIꢀWKHꢀSURGXFWꢀRUꢀꢒꢀꢇVHYHQꢈꢀ\HDUVꢀDIWHUꢀWKHꢀODVWꢀGDWHꢀRIꢀWKHꢀFRPSOHWH  
XQLWꢐVꢀILQDOꢀSURGXFWLRQꢎꢀZKLFKHYHUꢀFRPHVꢀILUVWꢍ  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE NOTES  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE NOTES  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12.14.10 BAD  
Printed in the U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Bolens Lawn Mower 113 084A User Manual
Bolens Lawn Mower OEM 190 821 User Manual
Dixon Lawn Mower ZTR 310 User Guide
Exmark Lawn Mower 4500 501 Rev A User Guide
Hayter Mowers Lawn Mower 184E XR44 User Guide
McCulloch Lawn Mower Accessory 17107 User Guide
Shibaura Lawn Mower GM222 User Guide
Snapper Lawn Mower XP21501KWV User Manual
Snapper Lawn Mower ZT20500BV User Manual
Swisher Lawn Mower T1360T T1360B1 T1360T T1360H T1360K T13560 RK1360 T14560 T17560 User Guide