Exmark Lawn Mower Mhp3615kac Mhp4815kac User Guide

For Serial Nos.  
510,000 & Higher  
Part No. 103-7195  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXMARK PARTS PLUS® PROGRAM  
EFFECTIVE DATE: September 1, 1995  
Program  
If your Exmark dealer does not have the Exmark part in  
stock, Exmark will get the parts to the dealer the next  
business day or the part will be FREE* Guaranteed!!  
How the Program Works  
1. If dealer does not have part in stock for a "down" unit at  
the time of request by customer, the dealer contacts his  
distributor by 1:00 p.m., local time, and requests Exmark  
Parts Plus® shipment of six (6) line items or less.  
2. Distributor ships part(s) to dealer or customer, as  
requested by dealer, same day, overnight UPS  
Distributor bills dealer for part and freight charges  
where applicable.  
3. If distributor does not have the part(s) in stock to satisfy Exmark Parts Plus® order, he contacts Exmark by  
3:00 p.m., central time, with an Exmark Parts Plus® order of six (6) line items or less.  
4. If order is received by 3:00 p.m., central time, Exmark ships part(s) direct to dealer or customer, as  
requested by distributor, same day, overnight UPS, Exmark bills the distributor for parts and shipping  
charges, where applicable.  
5. The customer pays for the part and freight if it is shipped under the Exmark Parts Plus® and if it arrives in  
accordance to the program.  
6. Who pays for the part and freight if it fails to arrive overnight in accordance to the program?  
A. Under any circumstance the customer does not pay.  
B. If the part does not arrive overnight due to:  
1. The dealer not submitting the Exmark Parts Plus® order to his Exmark distributor by 1:00  
p.m., the dealer pays for the part and freight.  
2. The Distributor being unable to ship the part the same day or not submitting the Exmark Parts  
Plus® order to Exmark by 3:00 p.m., central time, the Distributor pays for the part and freight.  
3. Exmark being unable to ship the part and the Exmark parts order is received by 3:00 p.m.,  
central time, Exmark pays for the part and freight.  
4. If the part does not arrive overnight due to the shipper (UPS), the shipper pays for the freight  
and Exmark pays for the part.  
The following restrictions apply -- The Exmark Parts Plus® Program is available only through  
participating Exmark Dealers and applies only to orders submitted on this program Monday through Thursday.  
Parts Plus service is available only in the 48 contiguous United States. UPS has initiated a Saturday delivery  
program to many areas of the continental United States and can be requested for an overnight shipment on  
Friday to be delivered Saturday. The next day air charge, plus the Saturday delivery fee will be the  
responsibility of the purchaser. Exmark Mfg. will assume no responsibility for Saturday delivery shipments.  
To qualify, all Exmark Parts Plus® orders must be received by Exmark by 3:00 p.m., central time. Orders  
must be six (6) line items or less. Exclusions from the Exmark Parts Plus® Program are: Any wholegood or  
accessory in its entirety, engines and engine replacement parts, 5-speed Peerless transmissions and 5-speed  
transaxles, hydraulic or hydrostatic wheel motors, cutter decks and engine decks or any item exceeding  
United Parcel Service size and weight restrictions.  
Due to UPS restrictions, aerosol spray paint is considered a hazardous material and cannot be shipped via  
UPS next day or Second Day Air.  
Exmark Manufacturing stocks a limited supply of parts for transaxles, pumps, and wheel motors. These parts  
can be ordered for Next Day Air shipment but will not be guaranteed per the Parts Plus Program.  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONGRATULATIONS on the purchase of your Exmark Mower. This product has been carefully  
designed and manufactured to give you a maximum amount of dependability and years of trouble-  
free operation.  
OPERATOR'S MANUAL  
This manual contains assembly, operating, maintenance, adjustment, and safety instructions  
for your Exmark mower.  
BEFORE OPERATING YOUR MOWER, CAREFULLY READ THIS MANUAL IN ITS  
ENTIRETY.  
By following the operating, maintenance, and safety instructions, you will prolong the life of  
your mower, maintain its maximum efficiency, and promote safe operation.  
If additional information is needed, or should you require trained mechanic service, contact  
your authorized Exmark equipment dealer or distributor.  
All Exmark equipment dealers and distributors are kept informed of the latest methods of  
servicing and are equipped to provide prompt and efficient service in the field or at their service  
stations. They carry ample stock of service parts or can secure them promptly for you from the  
factory.  
All Exmark parts are thoroughly tested and inspected before leaving the factory, however,  
attention is required on your part if you are to obtain the fullest measure of satisfaction and  
performance.  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
1. SAFETY............................................................................................. PAGE  
1.1 Safety Alert Symbol ......................................................................................1  
1.2 Training.........................................................................................................1  
1.3 Preparation ............................................................................................... 1-3  
1.4 Operation.................................................................................................. 4-5  
1.5 Maintenance & Storage............................................................................. 5-6  
1.6 Riding Attachments.......................................................................................6  
1.7 Safety Signs.............................................................................................. 6-8  
2. SPECIFICATIONS  
2.1 Model Number ..............................................................................................8  
2.2 Engine ..........................................................................................................8  
2.3 Fuel System..................................................................................................8  
2.4 Safety Interlock System ................................................................................8  
2.5 Steering/Brake Control..................................................................................8  
2.6 Transmission ................................................................................................9  
2.7 Wheel Drive System .....................................................................................9  
2.8 Tires ............................................................................................................9  
2.9 Deck ............................................................................................................9  
2.10 Dimensions..................................................................................................9  
2.11 Torque Requirements ................................................................................10  
3. ASSEMBLY INSTRUCTIONS  
3.1 to 3.18 Assembly ...................................................................................10-13  
4. OPERATION INSTRUCTIONS  
4.1 Controls .................................................................................................13-15  
4.2 Pre-Start ................................................................................................15-16  
4.3 Operation Instructions............................................................................16-18  
4.4 Transporting................................................................................................19  
5. MAINTENANCE & ADJUSTMENTS  
5.1 Periodic Maintenance.............................................................................19-25  
5.2 Adjustments...........................................................................................25-28  
6. WASTE DISPOSAL  
6.1 Motor Oil Disposal.......................................................................................28  
7. TROUBLE SHOOTING  
7.1 Mower Pulling Left or Right.........................................................................28  
7.2 Mower Cuts Unevenly.................................................................................29  
7.3 Engine Will Not Start...................................................................................29  
8. WIRING DIAGRAM........................................................................................30  
9
.
WARRANTY...............................................................................................31-32  
v
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. SAFETY  
1.1 SAFETY ALERT SYMBOL  
This SAFETY ALERT SYMBOL  
is used both in this manual and on the machine to  
identify important safety messages which must be followed to avoid accidents. This symbol  
means:  
ATTENTION! BECOME ALERT!  
YOUR SAFETY IS INVOLVED!  
The safety alert symbol appears above information which alerts you to unsafe actions or  
situations and will be followed by the word DANGER, WARNING, or CAUTION.  
DANGER: White lettering/Red background. Indicates an imminently hazardous situation  
which, if not avoided, WILL result in death or serious injury.  
WARNING: Black lettering/Orange background. Indicates a potentially hazardous situation  
which, if not avoided, COULD result in death or serious injury.  
CAUTION: Black lettering/Yellow background. Indicates a potentially hazardous situation  
which, if not avoided, MAY result in minor or moderate injury.  
1.2 TRAINING  
1.2.1 Regard the Exmark mower as a piece of power equipment and teach this regard to  
all who operate this unit.  
1.2.2 Read the instructions carefully. Familiarize yourself with the controls and the  
proper use of the equipment. If the operator(s) or mechanic(s) can not read  
English it is the owner’s responsibility to explain this material to them.  
1.2.3 Do not allow operation of this machine by untrained personnel. Never allow  
children, teenagers, or people unfamiliar with these instructions to use the mower.  
Local regulations may restrict the age of the operator.  
1.2.4 Avoid mowing while people, especially children, or pets, are nearby. Keep in mind  
that the operator or user is responsible for accidents or hazards occurring to other  
people or their property.  
1.3 PREPARATION  
1.3.1 Evaluate the terrain to determine what accessories and attachments are needed to  
properly and safely perform the job. Only use accessories and attachments  
approved by Exmark.  
1.3.2 The use of personal protective equipment, such as (but not limited to) protection for  
the eyes, ears, feet, and head is recommended.  
CAUTION  
POTENTIAL HAZARD  
This machine produces sound levels in excess of 85  
dBA at the operator’s ear when in operation.  
WHAT CAN HAPPEN  
Exposure to sound levels of 85 dBA or above for  
extended periods of time can cause hearing loss.  
HOW TO AVOID THE HAZARD  
Wear hearing protection when operating this machine.  
1.3.3 While mowing, always wear substantial footwear and long trousers. Do not operate  
equipment when barefoot or when wearing open sandals.  
- 1 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1.3.4 Thoroughly inspect the area where the equipment is to be used and remove all  
stones, sticks, wires, bones, and other foreign objects which may damage the  
equipment or cause personal injury to the operator or bystanders.  
WARNING  
POTENTIAL HAZARD  
Engine exhaust contains carbon monoxide, which is  
an odorless deadly poison.  
WHAT CAN HAPPEN  
Carbon monoxide can kill you.  
HOW TO AVOID THE HAZARD  
Do not run engine indoors or in a small confined area  
where dangerous carbon monoxide fumes can collect.  
DANGER  
POTENTIAL HAZARD  
In certain conditions gasoline is extremely flammable  
and highly explosive.  
WHAT CAN HAPPEN  
A fire or explosion from gasoline can burn you, others,  
and cause property damage.  
HOW TO AVOID THE HAZARD  
DO NOT smoke while refueling, and stay away from  
an open flame or where gasoline fumes may be ignited  
by spark.  
Refuel only outdoors.  
Store gasoline in an approved container and keep it  
out of the reach of children.  
Add fuel before starting the engine. Never remove the  
cap of the fuel tank or add fuel when engine is running  
or when the engine is hot.  
Never fill the fuel tank so that the gasoline level rises  
above a level that is 1/2” below the bottom of the filler  
neck to allow for gasoline expansion and prevent fuel  
spillage.  
If fuel is spilled, DO NOT attempt to start the engine.  
Move away from the area of the spill and avoid  
creating any source of ignition until fuel vapors have  
dissipated.  
Do not operate without entire exhaust system in place  
and in proper working condition.  
- 2 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DANGER  
POTENTIAL HAZARD  
In certain conditions gasoline is extremely flammable  
and highly explosive.  
WHAT CAN HAPPEN  
A static charge can ignite gasoline vapors. A fire or  
explosion from gasoline can burn you, others, and  
cause property damage.  
HOW TO AVOID THE HAZARD  
Purchase and store gasoline only in an approved  
container.  
Always place gasoline containers on the ground away  
from your vehicle before filling.  
Do not fill gasoline containers inside a vehicle or on a  
truck or trailer bed because interior carpets or plastic  
truck bed liners may insulate the container and slow  
the loss of any static charge.  
When practical, remove gas-powered equipment from  
the truck or trailer and refuel the equipment with its  
wheels on the ground.  
If this is not possible, then refuel such equipment on a  
truck or trailer from a portable container, rather than  
from a gasoline dispenser nozzle.  
If a gasoline dispenser nozzle must be used, keep the  
nozzle in contact with the rim of the fuel tank or  
container opening at all times until fueling is complete.  
WARNING  
POTENTIAL HAZARD  
Gasoline vapor can collect inside enclosed trailers and  
may be ignited by electrical sparks or hot  
engine/exhaust components.  
WHAT CAN HAPPEN  
Explosion and fire may occur, resulting in property  
damage, personal injury, and/or death.  
HOW TO AVOID THE HAZARD  
Provide adequate ventilation of any enclosed trailer to  
prevent build up of gasoline vapors, especially at floor  
level.  
Refuel only outdoors, never inside an enclosed trailer.  
Be sure all fuel tanks and gasoline storage containers  
have proper caps installed to prevent spillage and  
minimize vapor escaping into the trailer.  
Do not place any equipment that is leaking gasoline in  
an enclosed trailer.  
1.4 OPERATION  
Although hazard control and accident prevention are partially dependent upon the  
design and configuration of the equipment, these factors are also dependent upon  
the awareness, concern, prudence, and proper training of the personnel involved in  
the operation, transport, maintenance, and storage of the equipment. It is essential  
that all Operator Safety Mechanisms be connected and in operating condition prior  
to use for mowing.  
- 3 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
POTENTIAL HAZARD  
Operating engine parts, especially the muffler, become  
extremely hot.  
WHAT CAN HAPPEN  
Severe burns can occur on contact.  
Debris, such as leaves, grass, brush, etc. can catch fire.  
HOW TO AVOID THE HAZARD  
Allow engine parts, especially the muffler, to cool before  
touching.  
Remove accumulated debris from muffler and engine area.  
Install and maintain in working order a spark arrester before  
using equipment on forest-covered, grass-covered, or  
brush-covered unimproved land.  
WARNING  
POTENTIAL HAZARD  
Hands, feet, hair, clothing, or accessories can become  
entangled in rotating parts.  
WHAT CAN HAPPEN  
Contact with rotating parts can cause traumatic amputation  
or severe lacerations.  
HOW TO AVOID THE HAZARD  
Do not operate the machine without guards, shields, and  
safety devices in place and working.  
Keep hands, feet, hair, jewelry, or clothing away from  
rotating parts.  
1.4.1 Give complete, undivided attention to the job at hand.  
1.4.2 Mow only in daylight or good artificial light, keeping away from holes and hidden  
hazards. Do Not operate the mower when children or others are in the area!  
1.4.3 When feasible, avoid operating the equipment in wet grass.  
1.4.4 Use EXTREME caution when mowing and/or turning on slopes as loss of traction  
and/or tip-over could occur. The operator is responsible for safe operation on slopes.  
DANGER  
POTENTIAL HAZARD  
Mowing on wet grass or steep slopes can cause sliding and  
loss of control.  
WHAT CAN HAPPEN  
Loss of control and/or loss of operator’s footing could result  
in a fall with an arm or leg getting under the mower or  
engine deck, which may result in serious injury or death.  
HOW TO AVOID THE HAZARD  
Mow across slopes, never up and down.  
Do not mow slopes when grass is wet.  
Do not mow near drop-offs or near water.  
Do not mow slopes greater than 20 degrees.  
Reduce speed and use extreme caution on slopes.  
Avoid sudden turns or rapid speed changes.  
- 4 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
See inside the back cover to determine the approximate slope angle of the area  
to be mowed.  
Progressively greater care is needed as the slope increases.  
Always avoid sudden starting or stopping on a slope. If tires lose traction,  
disengage the blades and proceed slowly off the slope.  
Be aware that loss of traction may occur going downhill. Weight transfer to the  
front wheels may cause drive wheels to slip and cause loss of braking and  
steering.  
Watch for ditches, holes, rocks, dips, and rises that change the operating angle,  
as rough terrain could overturn the machine.  
Remove or mark obstacles such as rocks, tree limbs, etc. from the mowing area.  
Tall grass can hide obstacles.  
Use extreme care with grass catchers or attachments. These can change the  
stability of the machine and cause loss of control.  
1.4.5 Use EXTREME caution when backing up. LOOK BEHIND YOU!!  
1.4.6 Stop the blades when crossing surfaces other than grass, if mower must be tilted  
for transportation, and when transporting the mower to and from the area to be  
mowed.  
1.4.7 Never operate the mower with defective guards, shields, or covers. Always have  
safety shields, guards, switches, and other devices in place and in proper working  
condition.  
1.4.8 Do Not change the engine governor settings or over-speed the engine. Operating  
an engine at excessive speed may increase the hazard of personal injury.  
1.4.9 Place transmission in neutral, disengage PTO and engage park brake before  
starting engine.  
1.4.10 Start the engine carefully with feet well away from blades.  
1.4.11 Keep hands, feet, and clothing away from rotating parts while the mower is being  
operated.  
1.4.12 Stop the engine, wait for all moving parts to stop, and remove spark plug wire(s) or  
ignition key:  
Before checking, cleaning, or working on the mower.  
After striking a foreign object (inspect the mower for damage and make  
repairs before restarting and operating the mower).  
Before clearing blockages.  
Whenever you leave the mower.  
1.4.13 Stop the engine and wait for all moving parts to stop:  
Before removing the grass catcher.  
Before refueling.  
Before making height adjustments.  
1.4.14 Before stopping the engine, place the throttle control midway between the “slow”  
and “fast” positions. Allow the engine to run a minimum of 15 seconds; then stop  
the engine.  
1.4.15 The fuel system is provided with a shut-off valve. The fuel shut-off valve is used to  
shut off the fuel when:  
The machine will not be used for a few days.  
During transport to and from the job.  
When parking inside a building.  
1.4.16 This mower was designed for one operator only. Keep all others away from mower  
during operation.  
- 5 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1.4.17 Do Not mow with the grass deflector raised, removed or altered unless there is a  
grass collection system or mulch kit in place and working properly.  
1.4.18 Be aware of the mower discharge and direct discharge away from others.  
1.4.19 Do NOT operate the mower under the influence of alcohol or drugs.  
1.4.20 Use care when approaching blind corners, shrubs, trees, or other objects that may  
obscure vision.  
1.5 MAINTENANCE AND STORAGE  
1.5.1 For engine maintenance, follow the engine manufacture’s recommendations  
precisely as stated in the engine manual.  
1.5.2 Keep engine and engine area free from accumulation of grass, leaves, excessive  
grease or oil and other debris which can accumulate in these areas. These  
materials can become combustible and may result in a fire.  
1.5.3 Store fuel in a container specifically designed for this purpose in a cool, dry place.  
1.5.4 Keep the mower and fuel container in locked storage to prevent children from  
playing or tampering with them.  
1.5.5 Gasoline powered equipment or fuel containers should not be stored in a basement  
or any enclosed area where open pilot lights or heat appliances are present.  
1.5.6 Maximum mowing results and safety can only be achieved if the mower is properly  
maintained and operated correctly.  
1.5.7 Check all bolts frequently to maintain proper tightness.  
1.5.8 Keep all guards, shields, and all safety devices in place and in safe working condition.  
1.5.9 Frequently check for worn or deteriorating components that could create a hazard.  
1.5.10 All replacement parts must be the same as or equivalent to the parts supplied as  
original equipment.  
1.6 RIDING ATTACHMENTS  
1.6.1 Use only Exmark riding attachments. The use of other than Exmark riding  
attachments may create a hazardous condition resulting in injury.  
1.7 SAFETY SIGNS  
1.7.1 Keep all safety signs legible. Remove all grease, dirt, and debris from safety signs  
and instructional labels.  
1.7.2 Safety signs must be replaced if they are missing or illegible.  
1.7.3 When new components are installed, be sure that current safety signs are affixed to  
the replaced components.  
1.7.4 New safety signs may be obtained from your authorized Exmark equipment dealer  
or distributor or from Exmark Mfg. Co. Inc.  
1.7.5 Safety signs may be affixed by peeling off the backing to expose the adhesive  
surface. Apply only to a clean, dry surface. Smooth to remove any air bubbles.  
1.7.6 Familiarize yourself with the following safety signs and instruction labels. They are  
critical to the safe operation of your Exmark commercial mower.  
- 6 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PART NO. 1-303508  
LOCATION: Front of Mower  
Deck, Top Surface  
PART NO. 1-303517  
LOCATION: LH Side of Rear Surface of Mower Deck  
PART NO. 1-303518  
LOCATION: Transmission Shifter Plate  
PART NO. 1-403005  
LOCATION: RH & LH Corners  
of Mower Deck  
PART NO. 1-403143  
LOCATION: RH Side of Rear Surface of Engine Deck  
PART NO. 1-413206  
LOCATION: Top of Cutter Deck, Under  
Center Belt Shield (36”)  
PART NO. 1-413327  
LOCATION: Top of Cutter Deck, Under Belt  
Shield (48” & 52” Decks)  
PART NO. 1-413421  
LOCATION: Left Rear on Top of  
Engine Deck  
PART NO. 1-513746  
LOCATION: On Engine Blower  
Housing next to Muffler  
& on Center Belt Cover  
- 7 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PART NO. 1-553049  
LOCATION: Front of Mower Deck Top Surface  
PART NO. 103-1798  
LOCATION: RH Side of  
Console  
PART NO. 103-1077  
LOCATION: On Top LH Side of Mower Deck  
PART NO. 103-2244  
LOCATION: LH Side of Console  
PART NO. 103-2245  
LOCATION: RH Side of Console  
PART NO. 103-1623  
LOCATION: Console  
PART NO. 98-5954  
LOCATION: Under Mower Deck  
Belt Shield(s)  
- 8 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. SPECIFICATIONS  
2.1 MODEL NUMBER: MHP3615KAC; MHP4815KAC  
2.2 ENGINE  
2.2.1 Engine Specifications: See your Engine Owner's Manual.  
2.2.2 3600 RPM (No Load).  
2.3 FUEL SYSTEM  
2.3.1 Capacity: 5.0 gal. (18.9 L.)  
2.3.2 Type of Fuel: Regular unleaded gasoline, 87 octane or higher. In countries using  
the research method, it should be a 90 octane minimum.  
2.3.3 Fuel Filter: Replaceable in-line  
2.3.4 Fuel Shut-Off Valve: 1/4 turn  
2.4 SAFETY INTERLOCK SYSTEM  
Operator must have transmission in neutral and PTO disengaged to start engine.  
Release of OPC levers will cause the engine to stop if transmission is not in neutral  
and/or PTO is engaged.  
2.5 STEERING/BRAKE CONTROL:  
Fingertip drive control levers provide independent speed control, braking, and  
neutral to each drive wheel for moving, stopping, and power turning. Parking  
brakes are engaged by locking drive control levers in the “brake” position.  
2.6 TRANSMISSION:  
2.6.1 Peerless 700-070A, five speeds forward and one reverse.  
2.6.2 Speed Range: 1st 2.0 mph (3.22 km/h)  
4th 4.1 mph (6.60 km/h)  
5th 6.2 mph (9.98 km/h)  
Rev. 3.1 mph (4.99 km/h)  
2nd 2.7 mph (4.35 km/h)  
3rd 3.5 mph (5.63 km/h)  
2.7 WHEEL DRIVE SYSTEM:  
Banded double A-Section V-Belts, single topside idlers, and replaceable bolt-on  
drive sheaves and brake drums.  
Drive  
Pneumatic (Air-Filled)  
16 x 6.50-8  
2
Front Caster  
Semi-Pneumatic  
9 x 3.50-4  
2
2.8 TIRES:  
Size  
Quantity  
Tread  
Ply Rating  
Pressure  
Turf Master  
4
14 psi (97 kPa)  
Smooth  
2.9 DECK  
2.9.1 Cutting Width: Model 36 in. .......35.25 in. (89.5 cm)  
Model 48 in. .......47.25 in. (120.0 cm)  
2.9.2 Discharge: Right Side  
2.9.3 Blade Size:  
Model 36 in. .......18.00 in. (45.7 cm).... Qty. 2  
Model 48 in. .......16.25 in. (41.3 cm).... Qty. 3  
2.9.4 Type of Drive: Manual engagement of belt with over-center lock. Belt tension is  
adjustable via turnbuckle.  
2.9.5 Deck Mounting: Full floating deck is attached to out-front support frame,  
removable for service.  
2.9.6 Cutting Height: Adjusts in 1/2” (1.3 cm) increments from 1.5” (3.8 cm) to 4 1/2” (11.4 cm).  
- 9 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.10 DIMENSIONS  
2.10.1 Overall Width:  
36”  
48”  
46.25” (117.5 cm)  
36.1” (91.7 cm)  
58.25” (148.0 cm)  
48.1” (122.2 cm)  
Discharge chute down  
Discharge chute up (Transport only)  
36”  
48”  
2.10.2 Overall Length:  
2.10.3 Curb Weight:  
77.0” (196 cm)  
73.0” (185 cm)  
36”  
48”  
517 lbs. (234 kg)  
565 lbs. (256 kg)  
Weights will vary slightly depending on engine option.  
36”  
48”  
2.10.4 Overall Height:  
44.1” (112 cm)  
44.1” (112 cm)  
36”  
48”  
2.10.5 Tread Width (to outside of tires):  
35.2” (89.4 cm)  
35.2” (89.4 cm)  
2.11 TORQUE REQUIREMENTS  
BOLT LOCATION  
TORQUE  
Blade Mounting Bolt.................................................. 115-120 ft-lbs. (156-163 N-m)  
Cutter Housing Spindle Nut ...................................... 140-145 ft-lbs. (190-197 N-m)  
Mower Deck Support/Engine Deck Mount......................30-35 ft-lbs. (40-47 N-m)  
Engine Mounting Bolts (15 HP Kawasaki) ......................15-20 ft-lbs. (20-27 N-m)  
Transmission Shifter-lever Nut.......................................30-35 ft-lbs. (40-47 N-m)  
Anti-Scalp Roller Bolts....................................................40-45 ft-lbs. (54-61 N-m)  
Wheel Lug Nuts .............................................................90-95 ft-lbs. (122-129 N-m)  
3. ASSEMBLY INSTRUCTIONS  
3.1 Uncrate unit, and remove upper handle assembly, fuel tank, and linkages from top  
of crate.  
3.2 Remove and open the bolt bag.  
3.3 Loosen the 5/16" hardware at the two (2) discharge deflector hinge points so that  
the deflector is snug, but can be moved up and down freely.  
3.4 Refer to Parts Manual to help you identify and locate parts and their proper position.  
3.5 Apply retaining adhesive “Fel-Pro Retaining I or Retaining II” or “Loctite RC609 or  
680” on the two threaded studs from the bolt bag and install into the two left holes  
underneath fuel tank. Install the fuel tank on top of the fuel tank support with the  
studs going through the slots in the support. Install two 5/16-18 x 3/4” screws with  
a 5/16” SAE flat washer and 5/16” lock washer into the threaded holes in the right  
side of the fuel tank. Do not over tighten. Place a 5/16” SAE flat washer, then a  
spring, over each of the studs and fasten with a 5/16 nyloc nut. Tighten 5/16 nyloc  
nut fully then back off a 1/2 turn. This is to allow for normal fuel tank expansion  
with changes in temperature and fuel levels.  
3.6 Attach the fuel tank hose to the tank fitting and secure with the clamp provided.  
3.7 Position the lower end of the handle assembly on the outside of the upper rear  
section of the fuel tank and handle support. Install four 3/8-16 x 1" bolts (with four  
spring disk washers against the head of each bolt) from the outside in. Secure  
using four 3/8" whizlock nuts on the inside of each handle support and tighten until  
the spring disk washers are flat (See Figure 1).  
- 10 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FIGURE 1  
UPPER HANDLE MOUNTING  
3.8 Route the throttle cable along the right side of the upper handle, through the clip,  
under the fuel tank support, and position the cable on the left side of the engine.  
Attach throttle cable to engine:  
a) Position the throttle control lever (located on console) ¼” (6mm) from the upper  
end of the slot.  
b) Attach inner wire of the throttle cable to the top hole in the throttle control lever  
as shown in Figure 2.  
c) Loosen the clamp, place the cable behind it, and pull on the cable to move the  
throttle linkage to the full throttle position. Tighten the cable clamp screw.  
FIGURE 2  
SPEED CONTROL (THROTTLE CABLE HOOK-UP)  
3.9 Connect the PTO engagement linkages. Loosen jam nut and remove turnbuckle  
from lower linkage. Screw turnbuckle onto both upper and lower linkages  
simultaneously. (See figure 3) Note that the threads on upper linkage are left  
hand. See 5.2.2 for linkage adjustment.  
Note: ECS handles have the PTO linkage on the inside of the PTO engagement  
lever tab and the hairpin on the outside.  
FIGURE 3  
PTO ENGAGEMENT LINKAGE  
- 11 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.10 Install and adjust shifter lever.  
a)  
b)  
c)  
Remove the 3/8” nyloc nut and spring disc washer from the stud on top of the  
transmission. Install the shifter lever through slot in shifter lever plate and  
onto the stud on top of transmission. Be sure the square-hole washer  
remains between the lever and transmission. Replace the spring disc washer  
and nyloc nut (see figure 4). Torque the 3/8” nut to 35ft-lbs. (47N.M).  
Shift lever to second gear and check alignment of lever in slot of shifter plate.  
Clearance between top of lever and the top of the slot should be about equal to  
the clearance between bottom of the lever and the bottom of the slot (See  
figure 5). If it is not, remove lever and bend it slightly to adjust. DO NOT bend  
lever while it is attached to transmission. Reinstall lever and tighten hardware.  
Shift to neutral position. Lever should not contact the left edged of the upper  
slot. Push lever down. Lever should not contact the right edge of the bottom  
slot (See Figure 6). Shifter plate can be adjusted side to side to adjust position  
of lever relative to the slot in plate. Loosen the two bolts securing the shifter  
plate to the shifter lever legs. Adjust shifter plate and retighten bolts.  
FIGURE 5  
THIS CLEARANCE SHOULD BE EQUAL  
FIGURE 4  
SHIFTER LEVER  
TO TRANSMISSION  
FIGURE 6  
THIS CLEARANCE SHOULD BE EQUAL  
3.11 Install and adjust wheel drive linkages.  
a)  
Locate the (2) drive lever linkages which have a balljoint and jam nut installed  
on one end.  
Locate the (2) 5/16-18x1-3/4 hex head cap screws and (2) 5/16-18 nyloc nuts  
in the bolt bag.  
NOTE: During set up at the factory, an “L” or “R” may have been marked on  
the flats of the balljoints. If the balljoints are marked, assemble accordingly.  
If the balljoints are not marked, they may be assembled on either side.  
Thread the linkage into the swivel located on the wheel drive idler arm.  
Thread in until the flat edge of the drive lever aligns with the bottom of the  
roller notch in the neutral lock/park brake latch when the cap screw is inserted  
through the hole in the drive lever and the hole in the ball joint. Secure with a  
nyloc nut. Tighten nyloc nut. Repeat for the other side. See figures 7 and 8.  
- 12 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
b) The bend in the drive lever linkages should be positioned downward and  
slightly outward. If adjustment is needed, loosen jam nut below balljoint and  
rotate linkage. Tighten jam nut.  
Shift transmission lever to fifth gear. Insure that bend in right hand linkage is  
rotated outward enough that linkage clears shifter lever.  
If linkage is rotated too far out, ball joint may bind when drive lever is released  
into the “drive” position. Insure that this does not happen.  
FIGURE 7  
DRIVE LEVER LINKAGE INSTALLATION  
FIGURE 8  
DRIVE LEVER SETTING  
c)  
Adjust brakes by adjusting wingnut on the upper end of each brake rod.  
Tighten the wingnut until the brakes engage when the drive levers are  
squeezed enough allow the neutral lock/park brake latches to be placed into  
the “park brake” position. See Figure 7.  
d)  
Check for correct adjustment:  
Place the drive levers in the “park brake” position. The mower should not  
move forward or backward. If it does, tighten the wingnuts.  
Place the drive levers in the “neutral lock” position. The mower should  
move forward and backward freely. If it does not, loosen the wingnuts.  
NOTE: The neutral lock/park brake latches must be easily moved into the  
park brake position; if not the brake linkages must be adjusted again.  
- 13 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.12 Route the long unattached wiring harness lead, up the left hand side of the handle  
and connect the connector on the end of the shorter lead to the key switch.  
Connect the two flag terminals that are on the longer lead (in any order) to the  
operator presence control switch terminals underneath the control console.  
Fasten the lead to the handle with two small wire ties from the bolt bag, one at the  
upper end of the handle next to the console, and one at the very lower end of the  
handle where it attaches to the fuel tank support. Fasten the lead to the small hole  
in the channel under the console using another small tie from the bolt bag.  
3.13 If machine is shipped without muffler installed, install muffler with hardware provided.  
3.14 Service Engine: Refer to Engine Owner’s Manual.  
3.15 GREASE UNIT: NOTE: UNIT IS NOT GREASED AT THE FACTORY.  
Refer to 5.1.13, for locations and grease amounts.  
3.16 Follow pre-start instructions as outlined in 4.2.  
3.17 Perform any needed adjustments as outlined in the Adjustment Section.  
4. OPERATION INSTRUCTIONS  
4.1 Controls  
4.1.1 Familiarize yourself with the controls and operation of the unit.  
Carefully read the following information about the controls and their operation.  
4.1.2 Operator Presence Control (OPC) Levers: Located on the upper handle assembly  
directly above the handle grips. See Figure 9. When these levers are  
depressed, the OPC system senses that the operator is in the normal  
operator's position. When the levers are released, the OPC system senses  
that the operator has moved from the normal operating position and will kill  
the engine if either the transmission shift lever is not in the neutral position or the  
PTO is engaged. See Figure 9.  
4.1.3 Drive Levers: Located on each side of the upper handle assembly directly below the  
handle grips. See Figure 9. These levers individually control the clutching action of  
the wheel drive belts and the brakes. When the drive levers are all of the way out,  
the brakes disengage and the wheel drive belts engage.  
Gradually squeezing the left or right hand drive lever disengages the wheel drive  
belts, causing the left hand or right hand wheel to slow down until they reach  
neutral or stop. This makes the machine turn to the left or right respectively.  
Squeezing further engages the park brakes. The sharpness of the turn varies by  
how much the lever is squeezed. For straight ahead motion, smoothly release both  
drive levers to engage both drive wheels simultaneously.  
4.1.4 Neutral Lock/Parking Brake Latch: Located at the end of the handles. The purpose  
of these latches is to allow the operator to lock the drive levers in a "neutral" position  
where neither the wheel drive belts nor the brakes engage, or in a “park brake”  
position where the wheel drive belts are not engaged and the park brake is engaged.  
See Figure 9.  
Apply parking brakes whenever leaving the operators position.  
- 14 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FIGURE 9  
NEUTRAL LOCK/PARK BRAKE LATCH  
4.1.5 PTO Engagement: Located on the left side of the upper handle.  
To engage the blades, push the lever forward, or away from the operator, until the  
linkage locks over-center.  
To disengage the blades, pull the lever to the rear, or towards the operator.  
4.1.6 Choke Control: Choke is used to aid in starting a cold engine.  
The choke control is located on the front left corner of the fuel tank support and is  
activated by pulling the control outward. Once the engine has started move the  
choke control to the “OFF” position. DO NOT run warm engine with the choke in  
the “ON” position.  
4.1.7 Throttle Control: Located on the control console’s right side. The throttle is used to  
control engine speed. Moving the throttle control forward will increase engine  
speed and moving it to the rear will decrease engine speed.  
4.1.8 “Off-Run” Switch: Located on the console. Turn key to the “Run” position to allow  
the engine to be started. Turn key to the “Off” position to shut engine off.  
4.1.9 Fuel Shut-Off Valve: Installed in the fuel line midway between the tank and the  
engine. The fuel shut-off valve is used to shut off the flow of fuel when parking  
inside a building, during transportation to and from the job sites, and when the  
machine will not be used for a few days.  
Rotate valve 1/4 turn clockwise to shut fuel off. Rotate valve 1/4 turn counter-  
clockwise to turn fuel on.  
4.1.10 Transmission Shift Lever:  
Located under the control console and behind the fuel tank. It shifts the 5-speed  
transmission into five forward gears, neutral, and reverse. Shift transmission only  
when drive levers are in the neutral position. Shifting without drive levers in neutral  
may cause damage to the transmission.  
NOTE: Reverse is “reverse assist” only, meaning when the transmission is  
in reverse, the operator has to pull the unit backward to “assist” with the  
movement of the unit.  
4.2 PRE-START  
4.2.1 Refer to Maintenance and Adjustment Section 5 and perform all of the necessary  
inspection and maintenance steps.  
4.2.2 Fill fuel tank. For best results use only clean fresh regular grade unleaded  
gasoline with an octane rating of 87 or higher. Regular grade leaded gasoline may  
also be used; however, combustion chamber and cylinder head will require more  
frequent service. See Engine Owner's Manual.  
- 15 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Do not add oil to gasoline.  
Do not overfill fuel tank. Never fill the fuel tank so that the fuel level rises above a  
level that is 1/2” (1.3 cm) below the bottom of the filler neck to allow for fuel  
expansion and prevent fuel spillage.  
4.2.3 Make sure you understand the controls, their locations, their functions and their  
safety requirements.  
4
.
3 OPERATING INSTRUCTIONS  
4.3.1 Refer to Engine Owner’s Manual for detailed operating instructions regarding the engine.  
4.3.2 Starting Engine: Operator must have PTO disengaged and transmission in neutral.  
Open fuel shut-off valve.  
NOTE: Always engage the left and right neutral lock/park brake latches in the  
“park brake” position when starting the engine (See Figure 10 (d)).  
Pull out the choke control. Place the throttle control midway between the “Slow” and  
“Fast” positions. Turn the key to “Run” position. Pull recoil rope to start engine.  
After the engine warms up, gradually push in choke control. DO NOT run warm  
engine with the choke in the “ON” position.  
NOTE: Kawasaki engines generally need to be “choked” even when warm.  
4.3.3 Stopping Engine: Lock the drive levers in the “park brake” position, disengage PTO,  
and position transmission in neutral. Place the throttle control midway between the  
“slow” and “fast” positions. Allow the engine to run a minimum of 15 seconds; then  
turn the key to the “OFF” position.  
Close fuel shut-off valve if machine will not be used for a few days, when parking  
inside a building, or when transporting the unit.  
4.3.4 Drive Lever/Neutral Lock/Park Brake Latch Operation:  
To lock the drive levers in “neutral lock”, squeeze the drive levers to the “neutral”  
position. See Figure 10 (b). Place thumbs on the inner thumb lobe of the neutral  
lock /park brake latches and rotate them to the “neutral” position. See Figure 10  
(c). Release the drive levers.  
To lock the drive levers in “park brake”, squeeze the drive levers farther to the  
“brake” position. Place thumbs on the inner thumb lobe of the neutral lock/park  
brake latches and rotate them to the “park” position. See Figure 10 (d). Release  
the drive levers.  
CAUTION  
POTENTIAL HAZARD  
If the neutral lock/park brake latches are not completely  
engaged the drive levers could unexpectedly slip into the  
forward drive position.  
WHAT CAN HAPPEN  
If the drive levers slip into the drive position, the unit could lurch  
forward and cause injury or property damage.  
HOW TO AVOID THE HAZARD  
Be sure the drive levers are securely seated at the bottom of the  
“neutral” or “park” areas of the neutral lock latches.  
To place the drive levers in the “drive” position, slightly squeeze the drive levers  
while placing thumbs on the outer thumb lobe of the neutral lock/park brake latches  
(or the index finger on the front lobe) and rotate them from under the drive levers.  
Slowly and carefully release the drive levers. See Figure 10 (a).  
- 16 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
(a)  
(c)  
(b)  
(d)  
FIGURE 10  
DRIVE LEVER, NEUTRAL LOCK/PARK BRAKE LATCH OPERATION  
4.3.5 Drive Wheel Engagement and Turning: With drive levers in “neutral” or “park brake”  
position, shift transmission into desired gear. Squeeze both drive levers and move  
both neutral lock/park brake latches from the “neutral” or “park brake” position to  
the “drive” position.  
For straight ahead motion: Smoothly release both drive levers to engage drive wheels.  
For turning: Squeeze the right hand drive lever to turn right and the left hand drive  
lever to turn left (See Section 4.1.2).  
4.3.6 To Stop: Squeeze drive levers back to engage brakes. Move neutral lock/park  
brake latches into the “park brake” position and release the drive levers. Shift  
transmission to neutral.  
4.3.7 PTO Engagement:  
DANGER  
POTENTIAL HAZARD  
The rotating blades under the mower deck are  
dangerous.  
WHAT CAN HAPPEN  
Blade contact can cause serious injury or kill you.  
HOW TO AVOID THE HAZARD  
DO NOT put hands or feet under the mower or mower  
deck when the blades are engaged.  
- 17 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DANGER  
POTENTIAL HAZARD  
An uncovered discharge opening will allow objects to be  
thrown in an operator’s or bystander’s direction. Also,  
contact with the blade could occur.  
WHAT CAN HAPPEN  
Thrown objects or blade contact can cause serious  
injury or death.  
HOW TO AVOID THE HAZARD  
Never operate the mower with the discharge deflector  
raised, removed, or altered unless there is a grass  
collection system or mulch kit in place and working  
properly.  
Be sure that all persons are clear of mower deck and discharge area before  
engaging the PTO. Set throttle to “midway” position. Push the PTO engagement  
arm forward and down to engage blades. Accelerate to full throttle to begin  
mowing (See Section 4.1.4).  
4.3.8 PTO Disengagement: Pull upward and back completely on the PTO engagement  
arm to disengage the blades. (See Section 4.1.4)  
4.3.9 Changing Gears  
When changing gears, always squeeze drive levers to the neutral position. The shift  
lever may be moved with a knee or by hand (engage the neutral lock latches if  
shifting by hand).  
NOTE: Reverse gear is reverse assist only, the operator must pull the unit  
backwards.  
4.4 TRANSPORTING  
WARNING  
POTENTIAL HAZARD  
Loading the mower onto a trailer without strong enough  
or properly supported ramps could be dangerous.  
WHAT CAN HAPPEN  
The ramps could collapse causing the unit to fall, which  
could cause injury.  
HOW TO AVOID THE HAZARD  
Use proper ramps that are secured to the truck or trailer.  
Keep feet and legs out from under the unit when loading  
and unloading.  
If necessary, use assistance when loading.  
Be sure fuel shut-off valve is closed.  
Use a heavy duty trailer to transport the machine. Engage the park brakes and  
block wheels. After the wheels have been properly blocked, securely fasten the  
machine to the trailer with straps, chains, cables, or ropes. Be sure that the trailer  
has all necessary lighting and marking as required by law and use a safety chain.  
NOTE: When transporting machine, be sure to engage the park brakes.  
Failure to do so can result in damage and/or premature wear to drive train.  
Do not rely solely on the parking brake to hold machine on trailer.  
- 18 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. MAINTENANCE & ADJUSTMENTS  
WARNING  
POTENTIAL HAZARD  
While maintenance or adjustments are being made,  
someone could start the engine.  
WHAT CAN HAPPEN  
Accidental starting of the engine could seriously injure  
you or other bystanders.  
HOW TO AVOID THE HAZARD  
Remove the key from the ignition switch and/or pull the  
wire(s) off the spark plug(s) before you do any  
maintenance. Also push the wire(s) aside so it does  
not accidentally contact the spark plug(s).  
WARNING  
POTENTIAL HAZARD  
The engine can become very hot.  
WHAT CAN HAPPEN  
Touching a hot engine can cause severe burns.  
HOW TO AVOID THE HAZARD  
Allow the engine to cool completely before service or  
making repairs around the engine area.  
5.1 PERIODIC MAINTENANCE  
5.1.1 Check engine oil level.  
Service Interval: See Engine Owner's Manual  
a) Stop engine and wait for all moving parts to stop. Make sure machine is on a  
level surface.  
b) Check with engine cool.  
c) Clean area around dipstick. Remove dipstick and wipe oil off. Reinsert the  
dipstick (DO NOT screw into place). Remove dipstick and check oil level.  
d) If the oil level is low, add oil as specified in the Engine Owner’s Manual to  
bring the oil level up to the “FULL” mark on the dipstick.  
DO NOT OVERFILL.  
IMPORTANT: DO NOT operate the engine with oil level below the “LOW” (or  
“ADD”) mark or over the “FULL” mark.  
5.1.2 Clean engine air cooling system.  
Service Interval: See Engine Owner's Manual  
a) Stop engine and wait for all moving parts to stop. Remove key or spark plug  
wire(s).  
b) Clean all debris from engine air intake screen and from around engine  
shrouding.  
5.1.3 Clean grass build-up under deck and check mower blades.  
Service Interval: Daily  
- 19 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CAUTION  
POTENTIAL HAZARD  
Raising the mower deck for service or maintenance  
relying solely on mechanical or hydraulic jacks could  
be dangerous.  
WHAT CAN HAPPEN  
The mechanical or hydraulic jacks may not be enough  
support or may malfunction allowing the unit to fall,  
which could cause injury.  
HOW TO AVOID THE HAZARD  
DO NOT rely solely on mechanical or hydraulic jacks  
for support. Use adequate jack stands or equivalent  
support.  
a) Disengage PTO.  
b) Stop engine and wait for all moving parts to stop. Remove key or spark plug  
wire(s).  
c) Raise deck and block up using proper safety precautions.  
d) Clean out any grass build-up from underside of deck and in deck discharge  
chute.  
e) Inspect blades and sharpen or replace as required.  
f) If blade removal is necessary, be careful for the sharp cutting edges of the  
blades.  
g) Re-install the blades (if they were removed) and torque blade bolts to 115-120  
ft. lbs. Be sure the spring disc washer cone is installed toward the bolt head  
(See Figure 11).  
CAUTION  
POTENTIAL HAZARD  
Operating a mower deck with loose or weakened  
blade bolts can be dangerous.  
WHAT CAN HAPPEN  
A loose or weakend blade bolt could allow a blade  
rotating at a high speed to come out from under the  
deck, causing serious injury or property damage.  
HOW TO AVOID THE HAZARD  
Replace the blade bolt after striking a foreign object.  
(Use only Exmark replacement parts PN 103-1026 -  
blade bolt and PN 1-513208 – spring disc washer).  
DO NOT lubricate the threads of the bolt or spindle  
before assembly.  
Torque the blade bolt to 115-120 ft. lbs.  
h) Remove jack stands (or equivalent support) and lower deck to ground.  
- 20 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FIGURE 11  
BLADE BOLT INSTALLATION  
5.1.4 Check safety interlock system.  
Service Interval: Daily  
a)  
For your safety, your Exmark mower is equipped with Operator Presence  
Controls (OPC). When either the PTO is engaged, or the transmission shift  
lever is not in neutral and both hands are removed from the handles, the  
mower engine MUST stop.  
b)  
Check OPC circuits. Clear the area. Run engine at one-third throttle, then  
with drive levers and neutral lock/park brake latches in “park brake”  
position, Shift the transmission into gear and release OPC levers – engine  
MUST stop.  
Again, run engine at one-third throttle, move the transmission shifter lever to  
neutral, engage PTO and release OPC levers - engine MUST stop.  
c)  
If machine does not pass any of these tests, DO NOT operate. Contact  
your authorized EXMARK SERVICE DEALER.  
IMPORTANT: It is essential that all Operator Safety Mechanisms, be in  
place and in proper operating condition prior to mowing.  
5.1.5 Check for loose hardware.  
Service Interval: Daily  
a) Stop engine and wait for all moving parts to stop. Remove ignition key or  
spark plug wire(s).  
b) Visually inspect machine for any loose hardware or any other possible  
problem. Tighten hardware or correct the problem before operating.  
5.1.6 Check Brake and Wheel Drive Linkage Adjustment  
Service Interval: Daily  
Refer to Section 3.11. Note any bent linkage or hardware, which may need  
servicing or replacing.  
5.1.7 Service pre-cleaner element and air cleaner.  
Service Interval: See Engine Owner's Manual  
a) Stop engine and wait for all moving parts to stop. Remove key or spark plug  
wire(s).  
b) See engine owners manual for cleaning instructions.  
5.1.8 Change engine oil.  
Service Interval: See Engine Owner's Manual  
NOTE: Change oil after first five (5) hours of operation. Follow engine  
manufacturer’s recommendations for future oil changes.  
- 21 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
a) Stop engine and wait for all moving parts to stop. Remove key or spark plug  
wire(s).  
b) Drain oil while engine is warm from operation.  
c) The oil drain valve is located on left hand side of engine.  
Place pan under machine to catch oil and turn valve counter clockwise with a  
10 mm wrench to open valve. Allow oil to drain, then turn valve clockwise to  
close.  
d) Replace the oil filter as per Engine Owner's Manual. Clean around oil filter and  
unscrew filter to remove. Before reinstalling new filter, apply a thin coating of oil  
on the surface of the rubber seal. Turn filter clockwise until rubber seal contacts  
the filter adapter then tighten filter an additional 2/3 to 3/4 turn.  
e) Clean around oil fill cap and remove cap. Fill to the specified capacity and  
replace cap. Use oil as specified in Engine Owners Manual. Do not overfill.  
f) Start the engine and check for leaks. Stop engine and recheck oil levels.  
5.1.9 Check grease level, input and output shaft bearing wear on Peerless Transmission.  
(Replace gearbox grease yearly)  
Service Interval: 160 hrs.  
a) Stop engine, wait for all moving parts to stop, and remove key or spark plug  
wire(s).  
b) Place drive levers and neutral lock/park brake latches in the neutral lock  
position.  
c) Remove shifter lever from top of transmission.  
d) Remove shifter plate from top of transmission and the two leads from the  
neutral start switch.  
e) Release the tension on the transmission belt.  
f) Check for side play caused by bearing wear on the input and out put shafts of  
the transmission. Replace bearings if necessary.  
g) Remove the six bolts that fasten the upper case to the lower case and  
carefully remove the upper case half.  
h) Check the grease level in the lower case. The grease level should be  
approximately 1-1/2” to 1-3/4” (3.8 to 4.4 cm) from the gearbox bottom. If  
necessary, fill to proper level with Peerless grease (Part No. 788067).  
i) Reinstall upper case half and fasten in place with six bolts previously removed.  
j) Reinstall all parts removed in Steps c and d. Install drive belt and adjust  
tension as stated in Section 5.2.5.  
5.1.10 Check tire pressures.  
Service Interval: Pneumatic (air-filled) Drive Tires – 40 hrs.  
Semi-pneumatic Caster Tires – No Maintenance  
a) Stop engine and wait for all moving parts to stop. Remove key or spark plug  
wire(s). Check air pressure in drive tires; recommended tire pressure is: 12 to  
16 psi (83-110 kPa);  
b) Inflate tires to pressures stated above. Measure the circumference of each  
drive tire. Adjust tire pressures within the above range to try to make tire  
circumferences match as closely as possible.  
5.1.11  
Inspect Belt wear.  
Service Interval: 40 hrs.  
a) Stop engine and wait for all moving parts to stop. Remove key or spark plug  
wire(s).  
- 22 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
b) Remove deck support belt shield to check mower deck drive belt condition.  
c) Look under engine deck to check the transmission drive and clutching belt  
condition.  
d) Inspect wheel drive belt conditions  
e) Check the wheel drive idler arms to be sure they pivot freely. Disassemble,  
clean and grease pivot bushings if necessary.  
5.1.12 Inspect PTO Clutching Belt Tension.  
Service Interval: Check every 2 hrs. for first 8 hrs. operation then check every  
40 hrs. thereafter.  
a) Stop engine and wait for all moving parts to stop.  
b) Engage PTO lever.  
c) Look through the round hole in the left rear corner of the engine deck to  
inspect PTO clutching belt tension. Bolt on PTO engagement linkage  
bellcrank and indicator arm should align within 1/16” (See figure 14). Refer  
to section 5.2.2 for adjustment.  
5.1.13 Lubrication  
Service Interval: Refer to Chart.  
a) Stop engine, wait for all moving parts to stop, and remove key or spark plug  
wire(s).  
b) Lubricate fittings with one to two pumps of NGLI grade no. 2 multi-purpose gun  
grease. Refer to the following chart for fitting locations and lubrication schedule.  
GREASE LUBRICATION CHART  
FITTING  
LOCATIONS  
INITIAL  
PUMP  
QUANTITY  
SERVICE  
INTERVAL  
36”  
48”  
1. Caster Wheel Bearings  
2. Caster Pivots  
12  
2
2
2
2
2
1
1
1
2
8 hours  
8 hours  
8 hours  
40 hours  
40 hours  
Yearly  
2
3. Drive Wheel Idler Arm  
4. PTO Engagement Bellcrank  
5. Clutch Arm Pivot  
2
2
1
1
1
1
6. Mower Deck Idler Pivots  
7. Trans. Output Shaft Coupler  
2
1
2
2
40 hours  
No. 5 (Clutch Arm Pivot)  
Located Under Engine Deck  
No. 7 (Trans. Coupler)  
Located Below Fuel Tank Support  
No. 3 (Idler Arm Pivots)  
Disassemble and grease once a  
Month under a “No Load” condition  
c) Lubricate pivot points with a spray penetrating lubricant as directed below.  
SPRAY LUBRICANT CHART  
NO. OF  
PLACES  
1
SERVICE  
INTERVAL  
Weekly  
PIVOT POINT  
1. PTO Engagement Lever  
- 23 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
d) Lubricate drive wheel hubs once a year. First remove wheel, then remove  
hub cap. Lubricate the grease fitting on each wheel hub with an NGLI grade  
no. 2 multipurpose gun grease, until grease appears through outer bearing.  
Reinstall hub caps and wheels.  
e) Replace 5-speed gearbox grease yearly. Use 18 oz. of Peerless grease  
(Part No. 788067). See Section 5.1.9.  
5.1.14 Check spark plugs.  
Service Interval: 160 hrs.  
a) Remove spark plugs, check condition and adjust plug gap or replace with new  
plugs. See Engine Owner's Manual.  
5.1.15 Remove engine shrouds and clean cooling fins.  
Service Interval: See Engine Owner's Manual  
a) Stop engine, wait for all moving parts to stop, and remove key or spark plug  
wire(s).  
b) Remove cooling shrouds from engine and clean cooling fins. Also clean dust,  
dirt and oil from external surfaces of engine which can cause improper cooling.  
c) Make sure cooling shrouds are properly reinstalled. Operating the engine  
without cooling shrouds will cause engine damage due to overheating.  
5.1.16 Change fuel filter.  
Service Interval: As Required  
a) A fuel filter is installed in the fuel line between the fuel tank and the engine.  
Replace when necessary.  
5.1.17 Refer to Engine Operators Manual for detailed maintenance regarding the engine.  
5.1.18 Thread locking adhesives such as “Loctite 242” or “Fel-Pro, Pro-Lock Nut-Type” are  
used on the following fasteners:  
a) Transmission drive sheave setscrews.  
b) Wheel drive sheave setscrews on transmission output shafts.  
c) OPC lever setscrews.  
d) Sheave retaining bolt in end of engine crankshaft.  
e) Lower Sheave retaining bolt on clutch arm.  
f) Fuel tank bulkhead fitting threads (S/N 370,000 & higher).  
g) Cutter housing spindle nut.  
Adhesives such as “Loctite RC/609 or RC/680”or“Fel-Pro Pro-Lock Retaining I or  
Retaining II” are used on the following:  
a) OPC lever hubs and cross-shaft  
NOTE: Care must be used not to bond the bearing, next to each OPC hub, to the  
cross shaft which could cause binding of the OPC levers and erratic operation.  
b) Fuel tank studs, where studs are inserted into tank.  
5.1.19 An anti-seize compound is used on the following locations:  
a) Between engine crankshaft and transmission and blade drive sheaves.  
b) On clutch arm assembly between bearings and shaft and between lower  
sheave and shaft.  
c) Between transmission input shaft and sheaves.  
d) Between transmission output shafts and sheaves.  
e) Between transmission output shafts and bearings.  
- 24 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.1.20 Mobil HTS grease (or food-grade antisieze) is used in the following locations:  
a) Between the cutter housing spindle and bearings.  
b) Between the cutter housing spindle and sheave.  
c) Under top cutter housing bearing guard.  
5.1.21 Dielectric grease is used on all blade type electrical connections to prevent  
corrosion and loss of contact.  
5.2 ADJUSTMENTS  
5.2.1 Cutting height and anti-scalp roller adjustment.  
WARNING  
POTENTIAL HAZARD  
When the two front support rod hairpins are removed  
from the mower deck, the weight of the tractor section  
may cause the front frame to rise suddenly  
WHAT CAN HAPPEN  
If the unit rises suddenly, injury may occur.  
HOW TO AVOID THE HAZARD  
Securely hold down the front of the unit when the front  
support rod hairpins are removed.  
a) Stop engine, wait for all moving parts to stop, and remove key or spark plug  
wire(s).  
b) Install hairpin clips in the holes shown on sketch below for the desired cutting  
height (See Figure 13).  
IMPORTANT: To maintain correct cutting height and rake, check the  
following for proper adjustment.  
1. The front and rear hairpins are in the same holes with the proper spacers  
under the hair pins (See Figure 12).  
2. The tire pressures are set as directed in Section 5.1.10.  
3. The length of the rear deck support link assemblies should average 6.89”  
(approximately 6 7/8”) (17.5 cm) from the center of the balljoint to the  
center of the furthest hole (See Figure 12).  
NOTE: All (4) pins must equally support the weight of the deck. Adjustment  
in the length of the rear deck support assemblies may be necessary. If one  
side of the frame is longer than 6.89” (17.5 cm), than the opposite side must  
be shorter by the same amount.  
FIGURE 12  
CUTTING HEIGHT ADJUSTMENT  
- 25 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FIGURE 13  
ANTI-SCALP ROLLER BOLT INSTALLATION  
ANTI-SCALP ROLLER AND CUTTING HEIGHT ADJUSTMENT  
c) Adjust anti-scalp rollers for Normal Operating Conditions. Stop engine and  
wait for all moving parts to stop. Place rollers in one of the positions shown in  
Figure 13. Rollers will maintain 3/4 in. (19 mm) clearance to the ground to  
minimize gouging and roller wear or damage. For Maximum Deck Flotation,  
place rollers one hole position lower. Rollers should maintain 1/4 in. (6.4 mm)  
minimum clearance to ground. Do Not adjust rollers to support the deck. Be  
sure the spring disc washer is installed with the cone towards the nut. Tighten  
nuts properly.  
d) When operating in extremely rough conditions it may be necessary to position  
the anti-scalp rollers one or two holes higher than described in "b" to prevent  
damage to the rollers and/or bolt failure (See Figure 13).  
NOTE: When anti-scalp rollers are placed in these positions, reduced deck  
flotation will result.  
5.2.2 PTO engagement Linkage: Located between the PTO engagement lever on the  
left handle and the left rear corner of the engine deck.  
a) Stop engine and wait for all moving parts to stop.  
b) With PTO engaged, adjust the linkage length by loosening the lock nut on the  
turnbuckle and adjusting the turnbuckle so that the bolt on the bellcrank and  
the indicator arm align with each other within 1/16” (1.6 mm). See Figure 14.  
Tighten locknut against turnbuckle.  
FIGURE 14  
PTO ENGAGEMENT LINKAGE  
5.2.3 PTO Safety Switch: Mounted to a tab on the inside left side of the fuel tank support.  
a) Stop engine and wait for all moving parts to stop. Remove key or spark plug  
wire(s).  
b) With PTO disengaged and the bellcrank touching the rear of the slot in the  
engine deck, adjust the PTO safety switch (if needed) until the bellcrank arm  
is 5/16” (8 mm) from the switch body.  
c) Be sure the bellcrank DOES NOT touch the switch body or damage to the  
switch could occur.  
d) Retighten PTO switch mounting hardware.  
- 26 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.2.4 Engine to Cutter Deck Belt:  
No adjustment necessary.  
5.2.5 Transmission Belt Adjustment:  
a) Stop engine and wait for all moving parts to stop. Remove key or spark plug  
wire(s).  
b) To tighten transmission belt, loosen the 3/8” nyloc nut on transmission belt  
idler pulley. Slide bolt inward in slot and retighten nyloc nut.  
c) When properly adjusted, the belt should have 1/2” (12 mm) of deflection with three  
pounds (13.3 Nt) of pressure on the belt midway between the transmission and  
engine pulley.  
5.2.6 Wheel drive belts and scrapers:  
Be sure mud and grass scraper, on each side, is adjusted properly and centered in  
the pulley grooves. The pointed part of the scraper should be centered and as  
deep in the pulley groove as possible without rubbing at any point.  
NOTE: Wheel drive springs have three tension settings. See Section 5.2.11.  
5.2.7 Brake Adjustment:  
See 3.11 steps c) and d)  
5.2.8 Wheel drive linkage adjustment:  
See 3.11 steps a) and b)  
5.2.9 Shifter lever adjustment:  
See 3.10  
5.2.10 Shifter detent adjustment:  
Transmission shifter detent can be adjusted by adjusting the setscrew on the  
backside of transmission located just behind the neutral start switch. Turn setscrew  
in (clockwise) to hold the transmission shifter more positively in each gear and to  
increase the force on the lever required to shift gears.  
Turn setscrew out (counterclockwise) to decrease force on lever required to shift  
gears. Factory setting is to turn setscrew all the way in then back out 1-1/2 turns.  
IMPORTANT: Screwing setscrew in too far will prevent the transmission from  
shifting.  
5.2.11 Wheel drive spring tension adjustment:  
It may be necessary to increase wheel drive belt tension under certain conditions  
such as, wet grass, hilly terrain, or while pulling a sulky.  
a) Stop engine, wait for all moving parts to stop, and remove key or spark plug  
wire(s).  
b) Disengage neutral lock/park brake latches and release drive levers to lower  
spring force.  
c) Remove the 5/16-18 whizlock nut securing the adjustment bolt to the drive  
wheel shield. Locate bolt assembly in the desired position as follows  
Position A - Normal Conditions  
Position B - More Severe  
Position C - Most Severe  
NOTE: Lever force is lowest with bolt assembly in Position A and will increase in  
Positions B and C (See Figure 15).  
- 27 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FIGURE 15  
DRIVE BELT TENSION  
ADJUSTMENT POSITIONS  
6. WASTE DISPOSAL  
6.1 MOTOR OIL DISPOSAL  
Engine oil is a pollutant to the environment. Dispose of used oil at a certified  
recycling center or according to your state and local regulations.  
7. TROUBLE SHOOTING  
7.1 MOWER PULLING LEFT OR RIGHT.  
a)  
Check idler arm pulleys and drive sheaves for mud and/or grass buildup.  
Check for proper scraper position. See 5.2.6.  
Check to be sure idler arms pivot freely, if not lubricate idler pivots.  
Check for worn drive belts.  
b)  
c)  
NOTE: Wheel drive belts should be replaced as a set. A new belt should not  
be mixed with a worn belt.  
d)  
e)  
Check drive linkage adjustment - See 3.11 steps a) and b)  
Check for proper tire pressure in drive tires. Recommended tire pressure for  
the drive tires is 12 to 16 psi. (82-110 kPa) Higher pressures may be used in  
the tire on the side that it pulls to (up to 28 psi. (193 kPa)).  
Note: Different pressures may make mower cut unevenly.  
7.2 MOWER CUTS UNEVENLY.  
a)  
Check the drive tire pressure and tire circumference. See 5.1.10. A more  
uniform cutting height may be obtained with higher tire pressure on rough  
terrain. A lower tire pressure provides more flotation.  
b)  
c)  
d)  
Check deck support pins. Hairpin clips must be in the same hole position on  
each support pin.  
Check deck support alignment and check mounting brackets to be sure all  
bolts are tight.  
Check blades tip to tip for straightness. (They should be within 3/16” (4.8  
mm), or one blade width from being in line.)  
7.3 ENGINE WILL NOT START.  
a)  
Check that choke is in the “ON” position for a cold engine.  
NOTE: Kawasaki engines may need to be choked even when warm.  
b)  
c)  
d)  
e)  
Make sure the key switch is in the “ON” position  
Make sure transmission is in “true neutral” position. (See section 3.10c).  
Check that the PTO is disengaged and the PTO switch is depressed.  
Check that there is fuel in the tank and that the fuel valve is open.  
- 28 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
f)  
Check that the spark plug wire(s) are properly connected.  
g)  
Check for loose or faulty wiring connections. If it is necessary to disconnect  
wire connectors, Do Not pull on the wires while disconnecting.  
h)  
Check for corrosion at all wiring connections. Even minor corrosion may  
cause a faulty connection. Clean connector terminals thoroughly with  
electrical contact cleaner, apply dielectric grease and reconnect.  
IMPORTANT: It is essential that all operator safety mechanisms be connected and in  
proper operating condition prior to mower use.  
NOTE: After carefully checking the above steps, attempt to start the engine. If it  
does not start, contact your authorized Exmark service dealer.  
ENGINE TROUBLESHOOTING  
When a problem occurs, do not overlook the simple causes. For example, starting  
problems could be caused by an empty fuel tank. The following table lists some of the  
common causes of trouble. Do not attempt to service or replace major items or any items  
that call for special timing or adjustment procedures (such as valves, governor, etc.). Have  
this work done by your Engine Service Dealer.  
ENGINE TROUBLESHOOTING TABLE  
FAULTY  
SPARK  
PLUG  
BLOCKED INCORRECT  
DIRTY  
AIR  
SCREEN  
NO IMPROPER  
DIRT IN  
FUEL LINE  
DIRTY AIR  
FILTER  
ENGINE  
OVERLOADED  
FUEL  
OIL  
PROBLEM  
FUEL  
FUEL  
FILTER  
LEVEL  
Will not start  
Hard starting  
Stops suddenly  
Lacks power  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Operates  
erratically  
X
X
X
X
X
X
Knocks or pings  
Skips or misfires  
Backfires  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Overheats  
X
High fuel  
consumption  
X
X
X
X
- 29 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8. WIRING DIAGRAM – 15 HP KAWASAKI  
- 30 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9.  
2-Year Limited Warranty  
Exmark Turf Equipment  
(For units purchased on or after October 1, 2004)  
Conditions and Products Covered  
Owner’s Responsibilities  
Exmark Mfg. Co. Inc. and its affiliate, Exmark Warranty  
Company, pursuant to an agreement between them, jointly  
warrant on the terms and conditions herein, that we will repair,  
replace or adjust any part manufactured by Exmark and found  
by us (in the exercise of our reasonable discretion) to be  
defective in factory materials or workmanship for a period of  
two years.  
The Exmark turf equipment, including any defective part,  
must be returned to an authorized Exmark service dealer  
within the warranty period. This warranty extends only to turf  
equipment operated under normal conditions. You must  
properly service and maintain your Exmark product as  
described in the operator’s manual. Such routine  
maintenance, whether performed by a dealer or by you, is at  
your expense.  
This warranty applies to Exmark turf equipment purchased on  
or after October 1, 2004 sold in the US or Canada. This  
warranty may only be assigned or transferred to a second (or  
third) owner by an authorized Exmark dealer. The warranty  
period commences upon the date of the original retail  
purchase.  
As a condition to this warranty, customer shall have read the  
operator's manual and shall have completed and submitted to  
Exmark Warranty Company, within the prescribed time, the  
Exmark warranty registration.  
General Conditions  
Products  
Warranty Period  
2 years  
The sole liability of Exmark and Exmark Warranty Company  
with respect to this warranty shall be repair and replacement as  
set forth herein. Neither Exmark nor Exmark Warranty  
Company shall have any liability for any other cost, loss or  
damage, including but not limited to, any incidental or  
consequential loss or damage.  
All Products (except as noted below)  
All Attachments and Accessories  
Metro 21 Series  
1 year  
1 year  
Belts and Tires  
90 days  
Battery  
Engine*  
1 Year Prorated  
In particular, we shall have no liability or responsibility for:  
Warranty is covered by engine manufacturer  
Expenses related to gasoline, oil or lubricants.  
Travel time, overtime, after hours time or other  
extraordinary repair charges or charge relating to repairs  
or replacements outside of normal business hours at the  
place of business of the authorized Exmark service  
dealer.  
*Please refer to the engine manufacturer’s warranty statement  
that is included in the literature packet. We are not authorized  
to handle warranty adjustments on engines.  
This warranty only includes the cost of parts and labor.  
Rental of like or similar replacement equipment during  
the period of any warranty, repair or replacement work.  
Any telephone or telegram charges or travel charges.  
Loss or damage to person or property other than that  
covered by the terms of this warranty.  
Any claims for lost revenue, lost profit or additional cost  
as a result of a claim of breach of warranty.  
Attorney's fees.  
Items and Conditions Not Covered  
This warranty does not cover the following:  
Pickup and delivery charges to and from any authorized  
Exmark Service Dealer.  
Any damage or deterioration due to normal use, wear  
and tear, or exposure.  
Cost of regular maintenance service or parts, such as  
filters, fuel, lubricants, tune-up parts, and adjustments.  
Any product or part which has been altered or misused  
or required replacement or repair due to normal wear,  
accidents, or lack of proper maintenance.  
Any repairs necessary due to use of parts, accessories  
or supplies, including gasoline, oil or lubricants,  
incompatible with the turf equipment or other than as  
recommended in the operator's manual or other  
operational instructions provided by Exmark.  
No Claim of breach of warranty shall be cause for  
cancellation or rescission of the contract of sale of any  
Exmark mower.  
There are no understandings, agreements, representations, or  
warranties, express or implied, including but not limited to any  
regarding the merchantability (that product is fit for ordinary  
use) or fitness for use (that product is fit for a particular  
purpose), not specified herein, respecting the equipment which  
is the subject of this warranty.  
All warranty work must be performed by an authorized Exmark  
Service Dealer using Exmark approved replacement parts.  
Some states do not allow exclusions of incidental or  
consequential damages, or limitations on how long an  
implied warranty lasts, so the above exclusions and  
limitations may not apply to you.  
Instructions for Obtaining Warranty Service  
1. Contact any Exmark Service Dealer to arrange service at  
their dealership. To locate a dealer convenient to you,  
may also call 402-223-6375.  
This warranty gives you specific legal rights, and you may  
also have other rights which vary from state to state.  
2. Bring the product and your proof of purchase (sales  
receipt) to the Exmark Service Dealer.  
If for any reason you are dissatisfied with the Service Dealer’s  
analysis or with the assistance provided, contact us at:  
Exmark Customer Service Department  
The Exmark Warranty Company  
2101 Ashland Avenue  
Beatrice, NE 68310  
402-223-6375 or  
- 31 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
Download from Www.Somanual-s.c3o2m.-All Manuals Search And Download.  
SERVICE RECORD  
Date  
Description of Work Done  
Service Done By  
Download from Www.Somanual-s.c3o3m.-All Manuals Search And Download.  
ALIGN THIS EDGE WITH A VERTICAL SURFACE  
(TREE, BUILDING, FENCE POST, POLE ETC.)  
Download from Www.Somanual-s.c3o4m.-All Manuals Search And Download.  
SEE EXMARK’S COMPLETE  
LINE OF ACCESSORIES  
RIDING ACCESSORIES  
CUSTOM RIDE SEAT SUSPENSION SYSTEM  
DECK LIFT ASSIST KIT  
HITCH KIT  
LIGHT KIT  
MICRO-MULCH SYSTEM  
ROLL OVER PROTECTION SYSTEM (ROPS)  
SNOW BLADE  
SUN SHADE  
TRASH CONTAINER  
TURF STRIPER  
ULTRA VAC COLLECTION SYSTEM  
ULTRA VAC QUICK DISPOSAL SYSTEM  
WALK BEHIND ACCESSORIES  
GRASS CATCHER  
MICRO-MULCH SYSTEM  
STEERABLE SULKY  
SULKY HITCH KIT  
TURF STRIPER  
Check us out on the Web:  
WARNING  
The engine exhaust from this product  
contains chemicals known to the State of  
California to cause cancer, birth defects, or  
other reproductive harm.  
©1997 – 2004  
EXMARK MFG. CO. INC.  
PART NO. 103-7195  
(402) 223-6300  
INDUSTRIAL PARK BOX 808  
BEATRICE, NE 68310  
FAX (402) 223-5489  
ALL RIGHTS RESERVED  
PRINTED IN U.S.A.  
®
MFG. CO. INC.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Agri Fab Lawn Aerator 45 0381 User Manual
Bush Hog Lawn Mower ATH 720 User Manual
Exmark Lawn Mower 4500 352 User Guide
Exmark Lawn Mower 4500 507 User Guide
Flymo Trimmer Lawn Trimmer User Guide
Hayter Mowers Lawn Mower 616E User Guide
Husqvarna Lawn Mower Accessory 7021P User Guide
Snapper Lawn Mower S150XK0H2348 User Manual
Stiga Lawn Mower DINO 45 EURO User Guide
Troy Bilt Lawn Mower 546 User Guide