SPEEDZTR
ZTR®
Model Year 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
Page
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Warranty Policy. . . . . . . . . . . . . . . . . . . . . . . . . . .13
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Seat Adjustment Instructions. . . . . . . . . . . . . . . . .15
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-18
Operation Instructions. . . . . . . . . . . . . . . . . . 19-29
Care & Maintenance. . . . . . . . . . . . . . . . . . . .30-42
Standard Service Parts List. . . . . . . . . . . . . . . 43-44
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 45-46
Speedztr
Part No. 16134-0803
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
RIDING LAWN MOWERS,
IF IMPROPERLY OPERATED
CAN CAUSE SERIOUS INJURY OR DEATH
The most common causes of injury to the operator or bystander...
Blade Contact
Tip Over
Run Over
Back Over
.
..read and understand this manual to prevent injuries.
44
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Safety Alert Symbol
When you see this symbol, BE ALERT
to the potential for injury.
Follow recommended safety precautions
and safe operating practices.
DANGER
(highlighted in red)
indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
WARNING
(highlighted in orange)
indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION
(highlighted in yellow)
indicates a potentially
hazardous situation which,
if not avoided, may result in minor
or moderate injury. It may also
be used to alert against
unsafe practices.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Failure to observe the following safety instructions
could result in serious injury or death.
GENERAL OPERATION:
Read, understand, and follow all instructions in the
manual and on the mower before starting.
Only allow responsible adults, who are familiar with the
instructions, to operate the mower.
Clear the area of objects such as rocks, toys, wire, etc.,
which could be picked up and thrown by the blade.
Be sure the area is clear of other people before
mowing. Stop mower if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while braking.
Be aware of the mower discharge direction and do not
point it at anyone.
Do not operate the mower without either the entire
grass catcher or the deflector in place.
Slow down before turning.
Never leave a running mower unattended. Always turn
off blades, set parking brake, stop engine and remove
key before dismounting.
Turn off blades when not mowing.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
GENERAL OPERATION (continued):
Stop engine before removing grass catcher or
unclogging chute.
Mow only in daylight or good artificial light.
Do not operate the mower while under the influence of
alcohol or drugs.
Watch for traffic when operating near or crossing
roadways.
Use extra care when loading or unloading the mower
into a trailer or truck. Do not ride the mower when
loading and unloading.
Always wear safety goggles or safety glasses with side
shields when operating mower.
Data indicates that operators, age 60 years and above,
are involved in a large percentage of riding mower-
related injuries. These operators should evaluate their
ability to operate the riding mower safely enough to
protect themselves and others from serious injury.
Follow the manufacturer’s recommendation for wheel
weights and counterweights.
Maintain or replace safety & instruction labels as
needed.
Warning:
The engine exhaust from this product contains chemicals known to
the State of California to cause cancer; birth defects or other
reproductive harm.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SLOPE OPERATION:
Slopes are a major factor related to loss-of-control
and tip-over accidents,
which can result in severe injury or death.
All slopes requires extra caution.
If you cannot back up the slope or if you feel uneasy on it,
do not mow it!
DO
Mow across the slope with your Dixon ZTR - never up
or down.
Remove obstacles such as rocks, tree limbs, etc.
Watch for holes, ruts or bumps. Uneven terrain could
overturn the mower. Tall grass can hide obstacles.
Use slow speed. Tires may lose traction on slopes
even though the brakes are functioning properly.
Use extra care with grass catchers or other attach
ments. These can change the stability of the mower.
Keep all movement on the slopes slow and gradual. Do
not make sudden changes in speed or direction.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SLOPE OPERATION (continued):
DO (continued):
Avoid starting or stopping on a slope. If tires lose
traction, disengage the blades and proceed slowly
down the slope.
If front wheels lift off the ground, pull the levers back to
stabilize the mower.
DO NOT
Do not turn on slopes unless necessary, and then, turn
slowly and gradually downhill, if possible.
Do not mow near drop-offs, ditches, or embankments.
The mower could suddenly turn over if a wheel is over
the edge of a cliff or ditch or if an edge caves in.
Do not mow on wet grass. Reduced traction could
cause sliding.
Do not try to stabilize the mower by putting your foot on
the ground.
Do not use grass catcher on steep slopes.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SERVICE:
Use extra care in handling gasoline and other fuels.
They are flammable and vapors are explosive.
Use only an approved container.
Never remove fuel cap or add fuel with engine
running. Allow engine to cool before refueling.
Do not smoke while refueling.
Never store the mower or fuel container inside a
building where there is an open flame.
If fuel is spilled on clothing, change clothing
immediately.
To prevent fire and explosion caused by static
electricity:
Never fill containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always
place containers on the ground away from your
vehicle before filling.
When practical, remove fuel powered equipment
from the truck or trailer and refuel it on the
ground. If this is not possible, refuel such
equipment on a trailer with a portable container,
rather than from a fuel dispenser nozzle.
If a fuel dispenser nozzle must be used, keep the
nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is
complete. Do not use a nozzle lock-open device.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SERVICE (continued):
Never run a mower inside a closed area. The exhaust
fumes are toxic.
Keep nuts and bolts tight, especially blade attachment
bolts, and keep equipment in good condition.
Never tamper with safety devices. Check their proper
operation regularly.
Keep mower free of grass, leaves, or other debris
build-up. Clean up oil or fuel spillage. Allow mower to
cool before storing.
Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
Never make adjustments or repairs with the engine
running unless otherwise specified.
Grass catcher components are subject to wear,
damage and deterioration, which could expose moving
parts or allow objects to be thrown. Frequently check
components. Replace with original equipment parts,
when necessary.
Mower blades are sharp and can cut. Wrap blades or
wear gloves, and use extra caution when servicing
them.
Batteries contain sulfuric acid. To prevent burns avoid
contact with skin, eyes and clothing. To prevent fire or
explosion keep sparks and open flames away from
battery.
Before disconnecting the negative (-) ground cable,
make sure all switches are off.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
CHILDREN:
Tragic accidents can occur if the operator is not
alert to the presence of children.
Children are attracted to lawn mowers and the
mowing activity.
NEVER assume children will stay where they
were last seen.
Be alert to avoid accidents.
Keep children out of the mowing area and under the
watchful care of another responsible adult.
Be alert and turn mower off if a child enters the area.
Before and during backing look BEHIND and DOWN for
small children.
Never carry children. They may fall off and be seriously
injured or interfere with safe mower operation.
Never allow children to operate the mower.
Use extra care when approaching blind corners,
shrubs, trees, or other objects that may obscure vision.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Speedztr 42 & Speedztr 36
Chassis:
Body:
11 gauge steel welded frame assembly
All body parts made of high density polyethylene. Dent and
corrosion resistant.
Mower Deck:
Blade Drive:
36” Deck: 11 GA fabricated construction-36” cut width
42” Deck: 13 GA stamped steel construction-42” cut width
Electric clutch.
Transmission: Each rear wheel is independently driven by a Hydro Gear
EZT hydrostatic drive.
Engine:
Speedztr 42: 15.5 HP Briggs & Stratton Intek, single cylinder, overhead
valve, air cooled, gasoline, vertical shaft with cast iron
cylinder, pressure lube with spin-on filter.
Speedztr 36: 14.5 HP Briggs & Stratton Intek, single cylinder, overhead
valve, air cooled, gasoline, vertical shaft with cast iron
cylinder, pressure lube with spin-on filter.
Starting System: Electric-key switch operation w/safety interlock blade drive.
Tires:
Front - 11 x 4.00-5 ribbed tread (16-21 PSI)
Rear (42)-18 x 8.50 x 8 - 4 ply turf tread (8-14 PSI)
Rear (36)-18 x 6.50 x 8 - 4 ply turf tread (8-14 PSI)
Capacities:
Fuel
3 gallons
Engine Oil
1.5 quarts
Dimensions:
Width
40” maximum track width
40” to top edge of seat
72” hitch tab to front bumper
475 lbs
Height
Length
Weight
Additional information provided in service instructions under the individual component.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SEAT ADJUSTMENT INSTRUCTIONS
Speedztr
1.
Grasp seat slide adjuster and move it into
adjustment position.
2.
3.
Slide seat forward or backward.
Release seat slide adjuster.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
CONTROL LEVERS
Note: For access to the seat, move control levers to neutral
position and swing them outward.
TO GO FORWARD
•From neutral position, gently push control levers forward.
•To increase speed, move levers further forward.
TO GO BACKWARDS
•From neutral position, gently pull control levers toward
you.
TURNING
•Turning is controlled by moving one control lever slightly
forward or rearward of the other.
•To turn left, move left lever rearward of the right lever.
•To turn right, move right lever rearward of the left lever.
•To turn on mower’s own axis (zero turning radius), stop
and move one lever to reverse position and the other to
forward position.
BRAKING
•To brake mower, move both levers in direction opposite
of travel.
LEFT TURN OPPOSITE
Note: The pressure required to operate the mower is very light.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
PARKING BRAKE:
The parking brake is designed to hold the
mower from moving and is not intended for use
in stopping the mower while it is in motion. The
engine will stop if the parking brake is engaged
while the control levers are in the drive position.
Engage parking brake
before starting engine.
CAUTION
TO SET PARKING BRAKE:
The hand operated parking brake is located on
the left side of the front panel.
To engage brake, pull lever up.
To release brake, move lever down.
NOTE: Always set parking brake before dismounting.
Release parking brake before moving mower.
TRANSMISSION DRIVE SYSTEM
Allows the mower to turn on its own axis “ZERO TURNING
RADIUS”. Each lever controls one side of the mower.
NOTE: The pressure required to operate the mower is very light.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
BLADE DRIVE:
•Located on the control panel, on operator’s right.
•To engage the mower blade, pull up on the switch.
•To disengage mower blade, push down.
CIRCUIT BREAKER:
•Protection of the electrical system is by (1) 15 amp
circuit breaker.
•If circuit breaker trips, push button to reset.
•If this condition repeats, consult dealer for
inspection and repair.
THROTTLE CONTROL LEVER:
•Located on control panel to operator’s right.
•Throttle control for engine speed.
•Choke for engine starting.
•Throttle control should be set to MAXIMUM or wide
open setting to insure adequate cooling of the
engine and to maintain mower deck blade speed
while mowing.
MOWER DECK CUT HEIGHT LIFT LEVER:
•Located to the right side of the front panel.
•Controls the cutting height.
•Six positions of adjustment.
•Move lever down to lower.
•Move lever up to raise.
NOTE: Always use high for transport.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
The safe and successful operation of the Dixon
Speedztr will depend upon the operator having the
correct knowledge of all controls used on the mower
and making good judgements about the terrain to be
mowed.
NEVER allow anyone to operate the mower without
complete knowledge of all controls and their functions.
During initial operation, “learning to drive”, set throttle
at slow speed.
Sound judgement by the operator will prevent accidents.
BEFORE OPERATING MOWER:
1. Read engine manufacturer’s operating and
maintenance instructions.
2. Read and observe all safety instructions on
your mower and in the manual.
3. Check engine oil.
4. Check fuel cap to be sure it is in place.
5. Be sure parking brake is on.
6. Be sure mower blade drive is off.
7. Know how to stop engine. (Turn key to off
position).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
TESTING OF SAFETY INTERLOCK
SYSTEMS:
PARKING BRAKE SWITCH TEST:
a) Swing out control levers
b) Disengage blade drive switch
c) Put parking brake in OFF position
d) Turn ignition switch to START
Engine should not turn over or attempt to start.
CONTROL LEVER SWITCH TEST:
a) Disengage blade drive switch
b) Put parking brake in ON position
c) Swing control levers in
d) Turn ignition switch to START
Engine should not turn over or attempt to start.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
TESTING OF SAFETY INTERLOCK
SYSTEMS:
BLADE DRIVE SWITCH TEST:
a) Put parking brake in ON position.
b) Swing out control levers.
c) Engage blade drive switch.
d) Turn ignition switch to START.
Engine should not turn over or attempt to start.
SEAT SWITCH TEST:
a) In a SAFE AREA away from bystanders,
start the engine.
b) Leave levers swung out and parking
brake OFF.
c) Engage blade drive.
d) Raise slightly off seat.
ENGINE SHOULD STOP!
NOTE:
If Any Safety Check FAILS, Do Not
Operate The Mower until the system
has been checked and repaired by an
Authorized Dixon Dealer.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
TOWING TRAILERS AND OTHER
ATTACHMENTS:
Towing a trailer or other attachment that is too heavy could damage
the drive or cause the mower to become unstable. Limit loads to 150
pounds or less with this mower.
TO FREE WHEEL MACHINE
(Unlock Transmission):
Always turn off engine before engaging or disengaging the
hydro release (free wheel) levers. Never attempt to move the
lever with the engine running.
Push the hydro release levers (inboard of the rear tires) until
flange is held in place by the key hole slot. Release parking
brake.
To engage the transmission, pull release lever, down and
toward rear of machine so hydro release lever returns to its
normal position.
NOTE: Before pushing or towing tractor, transmission must
be unlocked and parking brake released. The tractor
should never be pulled at more than 2 miles per hour
or for any appreciable distance.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
CAUTION
Engage parking brake before
starting engine.
STARTING INSTRUCTIONS:
1. Parking brake must be on, control levers swung out, and blade
drive disengaged.
2. Move throttle control to “choke” position if engine is cold, full
throttle if warm.
3. Insert ignition key and turn to “start” position. When engine starts,
release ignition key. Key will return to “run” position.
4. Move throttle from “choke” to desired speed position.
5. Release parking brake.
6. Swing levers in.
7. Operate the mower per the “CONTROL” instructions on
Page 16.
CAUTION Do not operate the engine in an enclosed area
due to the harmful exhaust gas produced.
Note:
When mowing, “blade(s)
engaged”, throttle
control must be set to
the MAXIMUM or wide
open setting to insure
adequate cooling of the
engine and to maintain
mower deck blade
speed.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
MOWING WITH A MULCHING ATTACHMENT:
Mulching or recycling the grass clippings requires a totally
different mowing approach than would be normal when
side discharging or bagging the grass. There may be
instances or conditions where it is not possible to hide all
the recycled or mulched clippings.
In order to achieve the best results, please read and follow
the mulching tips listed below:
1. Set the engine speed control to the wide open or full
setting.
2. Place the mower deck cut height selector in either
the top or second notch. Never cut more than 3/4”
to 1” off the grass at any one time. Attempting to
cut more grass will result in the deck plugging and
cause the engine to stall.
3. It may be necessary to cut the lawn twice to achieve
acceptable mulching performance especially on first
cuttings or if the lawn is heavily fertilized.
4. Do Not Attempt To Cut Grass When It Is Wet.
Mulching performance will be very poor under wet
grass conditions.
5. Maintain Sharp Blade(s) Throughout The Cutting
Season. This is very important. Optimal mulching
performance cannot be obtained with a dull or nicked
up blade.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
MOWING WITH A MULCHING ATTACHMENT
(continued):
6. Keep the Underside Of The Mower Deck Clean.
Remove all grass and dirt build-up from the underside
of the pan, the baffles and deflectors after each use.
7. Alternate mower direction. This will evenly disperse
the mulched grass clippings over the lawn for even
fertilization.
If the mulching quality of the mower does not seem to be
satisfactory, try one or more of the following tips:
a.
b.
c.
d.
e.
f.
Raise the height-of-cut setting on your
mower.
It may be necessary to cut your grass
more frequently.
Operate the mower at a slower ground
speed.
Overlap cutting swaths instead of cutting
a full swath with each pass.
Mow across the marginal areas a second
time.
CUT HIGH - MOW OFTEN!
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
MOWING WITH A GRASS CATCHER
ATTACHMENT:
In order to achieve optimum performance when mowing
with a grass catching attachment, please read and follow
the tips listed below.
1. Set engine speed control to the wide open or full
setting.
2. Do Not Attempt To Cut Grass When It Is Wet.
Wet grass will clog both the underside of the deck
and the attachment chutes. Empty bags often to
prevent plugging.
3. If the grass is tall, place the mower deck cut height
selector in the top or second notch. “Initially” overlap
cutting swaths instead of a full swath with each
pass.
4. Keep The Underside Of The Mower Deck Clean.
Frequent removal of dried grass and dirt will greatly
assist in bagging of the clippings.
5. Maintain Sharp Blade(s) Throughout The Cutting
Season. Some grass catching attachments require
a “high-lift” blade. See your dealer for advice on the
type of blade(s) needed for your mower.
6. Operate the mower at a slower ground speed than
when mowing without a grass catching attachment.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
MOWING WITH A GRASS CATCHER
ATTACHMENT (continued):
7. Some mowing applications/use of grass
catchers may require that an optional weight box
be fitted to the mower to counter the weight of
grass in the bags. Please consult with your
dealer for more information regarding installation
and adding weight to the box.
CAUTION
•Watch for low hanging branches or other obstacles
which might hit the catcher top while turning or backing
the mower.
•Use care when backing to avoid pushing the grass bags
into the frame or “hot” exhaust muffler of the engine.
•Disengage blade and stop engine prior to clearing grass
from either the discharge chute or grass catcher
components.
•Keep all attachment bolts tight.
•Do Not operate the mower with the grass catching
attachment partially removed.
•Important: Do Not leave clippings in the bags while the
mower is stored. Damp grass clippings are a fire hazard
if left in the bag.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
SIDE DISCHARGE OF THE CLIPPINGS:
In order to achieve optimum performance when Side
discharging the grass clippings, please read and follow
the tips listed below. Additional information can be
found in the troubleshooting guide.
CAUTION Be sure that the deflector is properly
installed on the discharge chute.
1. Set engine speed control to the wide open or full
setting.
2. Do Not Attempt To Cut Grass When It Is Wet. Wet
grass will clog the underside of the deck and
discharge area.
3. If the grass is tall, place the mower deck cut height
lever in the top or second notch. “Initially” overlap
cutting swaths instead of a full swath with each
pass. Some applications may require a second
cutting.
4. Keep The Underside Of The Mower Deck Clean.
Frequent removal of dried grass and dirt will allow
the clippings to discharge correctly.
5. Maintain Sharp Blade(s) Throughout The
Cutting Season.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
GRASS HEIGHT & CUTTING SUGGESTIONS:
Do not attempt to cut grass when it is wet.
If the grass is tall, place the mower deck cut height
lever in the top or second notch. “Initially” overlap
cutting swaths instead of a full swath with each pass.
Some applications may require a second cutting.
Keep the underside of the mower deck clean.
Maintain sharp blades throughout the cutting season.
As a rule of thumb, never cut off more than 1/3 of
the total grass blade length. Correct mowing height
can reduce weeds and disease by 50% to 80%.
The following grass cut heights are based on
adequate moisture conditions and normal thatch
buildup in a healthy lawn. Some locations and
applications may require slightly different cut heights.
If in doubt, consult your local lawn professional for
assistance.
Grass Types
Bermudagrass
Bluegrass
Buffalograss
Ryegrass
Tall Fescue
Zoysiagrass
Best Cut Heights
1 - 2”
2 - 3”
11/2 -3”
2 - 3”
3-31/2”
1 - 3”
29
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & MAINTENANCE
CAUTION
Before performing any maintenance, turn off engine,
allow to cool & remove key.
Use extreme care when working on machinery.
Do not wear watch or jewelry.
Do not wear loose fitting clothes, and observe all
common safety practices with tools.
MAINTENANCE SCHEDULE
•Check deck serpentine belt...................................after 20 hours break-in
•Check crankcase oil level...............................................before each use
•Clean grass & debris from muffler & manifold area..........before each use
•Check air intake screen....................................................after each use
•Clean grass under deck....................................................after each use
•Check tire pressure.........................................................every 10 hours
•Inspect blades for sharpness............................................every 10 hours
•Clean air filter element....................................................every 25 hours
•Grease all zerks..............................................................every 50 hours
•Check all belts................................................................every 50 hours
•Change engine crankcase oil .................(5 hours break-in)every 50 hours
•Change engine oil filter....................................................every 50 hours
•Replace air filter element .............................annually or every 100 hours
30
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & MAINTENANCE
ENGINE:
For complete maintenance and operating information of the engine,
please refer to the maintenance instructions furnished by the
engine manufacturer and included in your Zero Turn Radius mower
information packet.
BATTERY:
Battery contains sulfuric acid electrolyte which
is poisonous and corrosive.
CAUTION
•This is a maintenance-free battery and the fluid level cannot be
checked.
•Charge battery if required.
OFF SEASON BATTERY STORAGE:
•DO NOT remove battery from mower.
•Clean top of battery and terminals with baking soda and water.
•Identify each cable so they can be reconnected to the correct
terminal.
•Disconnect cables from terminals. ALWAYS disconnect ground cable
first and reconnect last.
•Charge battery.
TIRES:
Correct tire pressure is essential for efficient operation of the mower.
Check tire pressure periodically. Inflate tires to the pressure listed
below.
Front tires
Rear tires (42) 18 x 8.50 x 8
Rear tires (36) 18 x 6.50 x 8
11 x 4.00 X 5
16-21 lbs.
8-14 lbs.
8-14 lbs.
Lug nuts or lug bolts should be checked regularly for tightness.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & MAINTENANCE
CUTTER BLADE MAINTENANCE:
CAUTION Stop engine and remove ignition key
for safety. Wear heavy, thick gloves
when holding onto cutter blade, avoid
the sharp edge of the blade.
Check sharpness of mower blades after every 10
hours of operation. Observe proper blade position
prior to removal.
1. Safely raise front of mower.
2. Hold or block blade from
turning.
3. Loosen blade bolt and remove
blade.
4. When replacing blade, tighten
blade bolt securely. Refer to
diagram. Be sure blade is
centered on pilot before
tightening nut to 60 ft. lbs.
Blades should be discarded when worn excessively.
DANGEROUS!
DO NOT USE
BLADE IN THIS
CONDITION!
New Blade
When notch starts,
discard blade
32
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & MAINTENANCE
BELTS:
Check belts every 50 hours. Replace any belts found to
be in poor condition.
BELT TENSION:
42” Deck
Mower Deck Serpentine Belt-P/N 6109
Manual adjustment. Refer to illustration below.
Engine to Mower Deck Belt-P/N 6111
Manual adjustment. Refer to illustration below.
36” Deck
Engine to Mower Deck Belt-P/N 61515
Manual adjustment. Refer to illustration below.
Idler Shock
Mount
Idler Weldment
“L” Rod
Hex Nut
3/4”
Tighten or Loosen
Hex Nut to achieve
this dimension
33
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & MAINTENANCE
DECK REMOVAL:
1.Place cut height lever in lowest cut position.
2.Loosen engine to deck belt tensioner L-rod to allow
belt to be removed from deck pulley and electric
clutch pulley.
3.Remove hair pin cotter and washer from one end
of deck support cross shaft. Note location of re-
maining shim washers used between chassis and
mower deck plates. Slide shaft from chassis and
mower deck.
4.Remove hair pin cotter and washer from each deck
L-rod. Remove L-rods from lift arms. At this
point, deck will drop down.
5.Carefully raise and support front of chassis. Slide
mower deck to either side for removal. (Reverse
procedure to reinstall deck assembly.)
NOTE:
When deck is reinstalled on frame, check
that belt is correctly routed in the grooves
of all pulleys and that belt idler is applying
tension to the back side of the belt.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & MAINTENANCE
DECK REMOVAL (continued):
36”
42”
35
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
MOWER DECK LEVELING PROCEDURE:
1. Place mower on a smooth, level surface and
check tire pressures to insure correct stance.
Tires should be inflated as follows.
Front: 16 - 21 lbs
Rear: 8 - 14 lbs
2. Turn each outer blade tip to align with the deck
in a side to side manner.
3. Measure from the floor surface up to thebottom
of the blade tip on the discharge side of the
mower. Retain this measurement. Move to the
opposite side and check to see if that
measurement is the same. If adjustment is
required, turn nut on one or both of the rear
L-rods until both measurements are equal.
4. Turn each outer blade tip to align with the deck
in a front to rear manner.
5. Measure from the floor surface up to the bot-
tom of the blade tips at both the front and rear
of the blades. Rear of blade tips should be to
1/8" to 1/4" higher than the front of blade tips.
If adjustment is necessary, turn nut on front L-
rod.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & MAINTENANCE
MOWER DECK LEVELING PROCEDURE
(continued):
NOTE: This will place the mower deck in a base
measurement position. Additional
adjustment may be required to achieve
desired cut for the type of grass or
conditions involved.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & MAINTENANCE
HOT oil may cause burns. Allow engine to
cool before draining oil.
CAUTION
CHANGING THE ENGINE OIL:
1. The “Dapco” oil drain valve is located on the left
side of the engine crankcase.
2. Place a suitable container under the drain valve
hose.
3. To drain, turn hex head valve stem counter-
clockwise with a 10mm wrench or socket. Open
to full open (approximately 7 turns).
4. After engine is drained, tighten hex stem.
5. Change oil filter.
6. Fill with oil (see steps on next page).
NOTE: Refer to engine manufacturer’s recommenda-
tions for frequency of oil changes.
Hex Head Valve
Stem
38
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & MAINTENANCE
HOT oil may cause burns. Allow
engine to cool before draining oil.
CAUTION
OIL FILL:
1. Clean any spilled oil from engine and chassis.
2. Refill engine with type, and quantity of oil
recommended by the engine manufacturer in
engine literature.
NOTE:Engine oil changes on the Speedztr Models
will require replacement of the oil filter.
These filters may be available from your
local Dixon Dealer.
PLEASEDISPOSEOFUSEDOILS ATPROPERCOLLECTIONCENTERS.
PROTECTYOURENVIRONMENT.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & MAINTENANCE
NEUTRAL ADJUSTMENT
DRIVE MACHINE UNTIL HYDROSTATS HAVE WARMED UP.
WITHENGINERUNNINGANDTHEPARKINGBRAKEOFF,SWING
OUT THE CONTROL LEVERS. IF MACHINE STARTS TO CREEP,
FOLLOWTHEINSTRUCTIONSBELOW.
1. Stop the engine, engage parking brake and raise rear of frame
with jack or blocks so that rear tires do not contact the ground.
2. Swing out the control levers, start the engine and release the
parking brake.
3. Raise the seat to access hydro control linkage. If right wheel
creeps, adjust right side linkage and vice-versa. Use procedure
below.
a. Loosen jam nuts on ends of the coupler P/N 7736.
b. If right wheel is creeping forward, turn coupler counter-
clockwise until neutral is achieved (clockwise for left side).
If right wheel is creeping backward, turn coupler clockwise
until neutral is achieved (counter-clockwise for left side).
c. Tighten jam nuts against coupler.
4. Stop engine and remove rear of machine from jack or blocks.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & MAINTENANCE
LUBRICATION:
CHASSIS:
(4) grease zerks 36”
(5) grease zerks 42”
LOCATIONS:
(1) each front wheel caster
(1) each mower deck hub
SERVICE INTERVALS:
Every 50 hours of operation or
once per season.
RECOMMENDED GREASE: Name brand wheel bearing
or multi-purpose grease
(3 pumps each)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & MAINTENANCE
ELECTRICAL SYSTEMS:
Keep all connections clean and tight.
CLEANING THE MOWER:
Wash mower periodically. Clean above and below
deck.
High pressure washing and alkaline based soaps can
cause damage to bearings and other parts of the mower.
After washing your mower, start the engine and engage
the mower deck for a few minutes to disperse any water
that may have accumulated in bearings, pulleys or fans.
Note: Allow mower to cool before washing. If bearings
are hot, they will draw moisture inside as they
dry and cause corrosion.
SERIAL NUMBERS:
The serial number is located on frame at rear of
engine.
WARRANTY:
Refer to warranty information (page 13).
PARTS/SERVICE:
See your Dixon dealer for replacement parts,
warranty or service.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD SERVICE PARTS LIST
42” Deck
~Blades~
Hi-Lift - P/N 8688 (Standard)
Lo-Lift - P/N 6236
~Belts~
Engine to Mower Deck - P/N 6111
Serpentine - P/N 6109
Engine to Transmission - P/N 16108
36” Deck
~Blades~
Hi-Lift - P/N 8688 (Standard)
Lo-Lift - P/N 6236
~Belts~
Engine to Mower Deck - P/N 61515
Engine to Transmission - P/N 16108
43
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD SERVICE PARTS LIST
BRIGGS & STRATTON AIR AND OIL FILTERS
Refer to Briggs & Stratton Engine Operator’s
Manual for correct service intervals for engine
oil changes and air filter maintenance.
Protect your engine investment, use only
original equipment filters. Refer to the Briggs
& Stratton Engine Operator’s Manual or ask
your dealer for correct replacement parts.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
1. ENGINE WON’T TURN OVER
Mower blades engaged- - - - - - - - - - - - - - - - - - - disengage blades
Parking brake not on- - - - - - - - - - - - - - - - - - engage parking brake
Circuit breaker trips- - - - - - - - - - - - - - - - - - - - - - - - -reset breaker
Dead battery- - - - - - - - - - - - - - - - - - - - - - - - - - charge or replace
Solenoid- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
Ignition switch- - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
Starter- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
2. ENGINE WILL TURN OVER BUT WON’T START
No fuel- - - - - - - - - - - - - - - refuel and/or clean or replace fuel filters
3. HARD TO START ENGINE
Fuel line clogged- - - - - - - - - - - - - clean fuel line and check fuel filter
Faulty fuel pump- - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
4. ENGINE STARTS BUT CUTS OUT
Water in fuel- - - - - - - - - - - - - - -drain old fuel-replace with new fuel
Clogged fuel line- - - - - - - - - - - - - - - - - - - - - - - - - - check fuel filter
Fuel tank vent plugged- - - - - - - - - - - - - - - - - - - - - -clean fuel vent
Faulty fuel pump- - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer
5. ENGINE OVERHEATED
Air intake screen or fins clogged- - - - - -clean intake screen and fins
Oil level too low or too high- - - - - - - - - - - - - - - - - - - -adjust oil level
Running engine too slow - - - - - - - - - - - - - - - - - -run engine faster
45
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
6. ENGINE RUNS BUT MOWER WON’T MOVE FORWARD
Drive belt broken or slipping- - - - - - - - - - - - - - - - replace drive belt
Transmission oil low- - - - - - - - - - - - - - - - - - - - - - - - - - - - add oil
Damaged transmission- - - - - - - - - - - - - - - - - - - - - -consult dealer
Transmission by-pass may be engaged- - - - disengage(see page 20)
7. MOWER LOSES POWER OR TRANSMISSION OVERHEATS
Engine air filter-- - - - - - - - - - - - - - - - - - - - - - - - - - clean or replace
Transmission damage- - - - - - - - - - - - - - - - - - - - - - -consult dealer
8. ENGINE STALLS WHEN BLADES ARE ENGAGED
Operator not on seat- - - - - - - - - - - - - - - - - - - - - - - - - -sit on seat
Faulty interlock system- - - - - - - - - - - - - - - - - - - - - - consult dealer
Fauty blade spindle bearing - - - - - - - - - - - - - - - - - - consult dealer
Deck drive belt not properly routed- - - - - - - - - - - - - - - - - - reroute
Blades blocked by foreign material - - - - - - - - - - - clean under deck
9. DRIVE SYSTEM
Mower pulls to side- - - - - - -check tire inflation/adjust control linkage
Mower creeps in neutral- - - - - - - - - - - - - - - - adjust control linkage
Low on power- - - - - - - - - - - - - - - - - - - - - - - - - -check belt tension
10. CUT QUALITY
Cut uneven left to right- - - - - - - - - - - -check tire inflation/level deck
Ends of grass blades are ragged- - - - - - - - - - - - - - sharpen blades
Poor dispersal of grass- - - - - - - - - - clean deck/check for loose belt
Skips in spots- - - - - - - - - - -check for loose belt/slow ground speed
46
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S
INFORMATION
DIXON INDUSTRIES, INC.
a BLOUNT International Inc. Co.
P.O. Box 1569
Coffeyville, Ks 67337-0945
620-251-2000
FAX 620-251-4117
Date of Purchase
Mower Model Number
Mower Serial Number
Purchased From
Name
Address
DATE OIL CHANGED
DATE ENGINE TUNED
47
Download from Www.Somanuals.com. All Manuals Search And Download.
ZTR®Mowers
The engine exhaust from this product
contains chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.
WARNING:
Dixon® and ZTR® are registered trademarks of
Dixon Industries, Inc.
DIXON INDUSTRIES, INC.
a BLOUNT International Inc. Co.
P.O. Box 1569
Coffeyville, Ks 67337-0945
620-251-2000
Speedztr
Part No. 16134-0803
Download from Www.Somanuals.com. All Manuals Search And Download.
|