Craftsman Lawn Sweeper 486242211 User Guide

Owner's Manual  
®
STOP  
42" LAWNSWEEPER  
DO NOT RETURN TO STORE  
For Missing Parts or Assembly  
Questions Call 1-866-576-8388  
Model No's. 486.242211  
cks  
o
osmith  
er  
R
A
CAUTION:  
• Safety  
Before using this product, read this  
manual and follow all Safety Rules  
and Operating Instructions.  
• Assembly  
• Operation  
• Maintenance  
• Parts  
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.  
FORM NO. 40637 (REV. 3/12/08)  
PRINTED IN U.S.A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ACCESSORIES AND ATTACHMENTS  
These accessories were available when the unit was purchased. They are also available at most Sears retail outlets and  
service centers. Most Sears stores can order repair parts for you when you provide the model numbers of your tractor and  
sweeper  
TheFrontMountDethatcher,Model486.24219attaches  
to the lawn sweeper to help loosen and remove dead  
grass and thatch from the lawn while sweeping.  
CARTON CONTENTS (Loose Parts in Carton)  
1. Sweeper Housing Assembly  
2. Bag Arm Tube (2)  
3. Left Hitch Tube  
7. Height Adjustment Handle  
8. Right Hitch Tube  
9. Brush Assembly (2)  
13. Hopper Support Rod (2)  
14. Bag Frame Strap  
15. Hopper Bag  
4. Hitch Bracket  
5. Hitch Bracket (Straight)  
6. Height Adjustment Strap  
10. Upper Hopper Side Tube (2)  
11. Rear Hopper Tube (2)  
12. Lower Hopper Side Tube (2)  
16. Rope  
11  
10  
10  
9
12  
11  
2
12  
1
13  
14  
3
15  
6
16  
7
2
4
5
8
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
HARDWARE PACKAGE CONTENTS  
SHOWN FULL SIZE  
F
G
A
B
C
D
E
O
P
M
K
N
Q
R
L
I
S
T
U
J
NOT SHOWN FULL SIZE  
Y
V
W
X
Z
REF qTY DESCRIPTION  
REF qTY DESCRIPTION  
A
B
C
D
E
F
G
I
J
K
L
M
N
2
2
4
1
2
1
4
4
Hex Bolt, 5/16 x 2-1/2" Lg.  
Hex Bolt, 5/16 x 2" Lg.  
Carriage Bolt, 5/16" x 1-1/2"  
Hex Bolt, 5/16 x 1-1/4" Lg.  
Hex Bolt, 5/16" x 1"  
Carriage Bolt, 5/16" x 1"  
Hex Bolt, 1/4" x 1"  
Nylock Nut, 1/4"  
O
P
Q
R
S
T
U
V
W
X
Y
Z
2
2
2
2
1
1
2
2
1
1
1
4
Clevis Pin, 3/8" x 1/2"  
Clevis Pin, 1/4" x 1-1/8"  
Clevis Pin, 1/4" x 1-3/4"  
Clevis Pin, 3/8" x 3"  
Pivot Bushing  
Spacer Bushing  
Hitch Spacer, 3/4"  
Vinyl Cap  
Grip  
Knob, Plastic  
Hitch Pin  
Plastic Plug  
11 Nylock Nut, 5/16"  
4
1
1
8
Flat Washer, 5/16"  
Star Washer  
Hair Cotter Pin, 1/8"  
Hair Cotter Pin, 3/32"  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY  
IMPORTANT: The overlap bristles at the bottom of each  
TOOLS REqUIRED FOR ASSEMBLY  
brush help support the back side of the brush for better  
sweeper performance. Be sure the sweeper is turned  
as shown in figures 2 and 3 to correctly assemble the  
brushes.  
(2) 7/16" Open End or Box End Wrenches  
(2) 1/2" Open End or Box End Wrenches  
STEP 2: (SEE FIGURE 2)  
Attach the brush assembly with the red brush retainer  
to the right end of the brush shaft using two 1/4" x  
1" hex bolts (G) and 1/4" nylock nuts (I). The brush  
retainer marked with red ink must be placed to the  
middle of the sweeper.  
REMOVE PARTS FROM CARTON  
To protect painted parts, lay them on cardboard or a  
mat.  
Remove the sweeper housing, the loose parts and the  
hardware package from the carton. Lay out the parts  
and hardware as shown on pages 3 and 4.  
1/4" NYLOCK NUT (I)  
STEP 1: (SEE FIGURE 1)  
Each brush assembly has one brush retainer  
marked with either red or black ink. Lay out the brush  
assemblies as shown so that the brush retainers  
marked with ink are in the middle with the red one on  
the right and the black one on the left.  
BRUSH RETAINER  
MARKED RED  
1/4" x 1"  
HEX BOLT (G)  
OVERLAP BRISTLES  
OVERLAP  
BRISTLES  
BRUSH RETAINER  
MARKED RED  
BRUSH RETAINER  
MARKED RED  
BRUSH RETAINER  
MARKED BLACK  
FIGURE 2  
FIGURE 1  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 3: (SEE FIGURE 3)  
STEP 4: (SEE FIGURE 4)  
Attach the brush assembly with the black brush  
retainer to the left end of the brush shaft using two  
1/4" x 1" hex bolts (G) and 1/4" nylock nuts (I). The  
brush retainer marked with black ink must be placed  
to the middle of the sweeper.  
Cut off the plastic tie that holds the height adjustment  
tube in place.  
Assemble the R.H. hitch tube to the sweeper housing  
using two 5/16" x 1-1/2" carriage bolts (C), and two  
5/16" nylock nuts (J). Do not tighten yet. Repeat for  
the L.H. hitch tube.  
Turn a wheel to rotate the brushes. (The wheels drive  
the brushes in one direction only.) The overlap bristles  
should be on the back side of the brush as it rotates.  
5/16" NYLOCK NUT (J)  
1/4" x 1"  
HEX BOLT (G)  
BRUSH RETAINER  
MARKED BLACK  
5/16" x 1-1/2"  
CARRIAGE BOLT (C)  
1/4" NYLOCK NUT (I)  
FIGURE 3  
FIGURE 4  
STEP 5: (SEE FIGURE 5)  
Fasten the hitch tubes together using two 5/16" x  
2-1/2" hex bolts (A) and 5/16" nylock nuts (J). Do not  
tighten yet.  
5/16"  
NYLOCK NUT (J)  
5/16" x 2-1/2"  
HEX BOLT (A)  
FIGURE 5  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 6: (SEE FIGURE 6 AND 7)  
STEP 7: (SEE FIGURE 8)  
Assemble the height adjustment handle to the inside  
of the bracket on the end of the height adjustment  
tube. Use two 5/16" x 1" hex bolts (E), 5/16" flat  
washers (K) and 5/16" nylock nuts (J). Tighten.  
Assemble the grip (W) onto the height adjustment  
handle.  
If your tractor hitch has 10" to 13" ground clearance  
refer to figure 6. If your tractor hitch has 8" to 10"  
ground clearance refer to figure 7.  
Assemble the hitch brackets to the hitch tubes using  
two 5/16" x 2" hex bolts (B) and 5/16" nylock nuts (J).  
The bolts should straddle the front hitch tube bolt. Do  
not tighten yet.  
At this time tighten the four bolts fastening the hitch  
tubestothesweeperhousing.Next, tightenthetwobolts  
fastening the ends of the hitch tubes together. Finally,  
tighten the two bolts fastening the hitch brackets to the  
hitch tubes.  
GRIP (W)  
Assemble the hitch pin (Y), two 3/4" hitch spacers (U)  
and the 1/8" hair cotter pin (M) to the hitch brackets.  
5/16" x 1" HEX BOLT (E)  
5/16" FLAT WASHER (K)  
5/16" x 2"  
HEIGHT  
HEX BOLT (B)  
ADJUSTMENT  
HANDLE  
HITCH PIN (Y)  
5/16" NYLOCK NUT (J)  
FIGURE 8  
HITCH BRACKET  
3/4" SPACER (U)  
STEP 8: (SEE FIGURE 9)  
HITCH BRACKET  
(STRAIGHT)  
Assemble onto a 5/16" x 1-1/4" hex bolt (D) in the  
order listed, a 5/16" flat washer (K), the pivot bushing  
(S), the height adjustment strap and the spacer  
bushing (T). Insert the bolt through the upper part of  
the double hole in the end of the sweeper housing  
and secure it with a 5/16" nylock nut (J). Tighten.  
5/16" NYLOCK  
1/8" HAIR  
NUT (J)  
COTTER PIN (M)  
FIGURE 6  
5/16" NYLOCK NUT (J)  
SPACER BUSHING (T)  
5/16" x 2"  
HEX BOLT (B)  
HEIGHT ADJUSTMENT  
STRAP  
HITCH PIN (Y)  
PIVOT BUSHING (S)  
5/16" FLAT WASHER (K)  
HITCH BRACKET  
(STRAIGHT)  
5/16" x 1-1/4"  
HEX BOLT (D)  
3/4" SPACER (U)  
HITCH BRACKET  
5/16" NYLOCK  
NUT (J)  
1/8" HAIR  
COTTER PIN (M)  
FIGURE 7  
FIGURE 9  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 9: (SEE FIGURE 10)  
ASSEMBLY OF HOPPER BAG  
Place the star washer (L) between the height  
adjustment handle and the height adjustment strap.  
Insert the 5/16" x 1" carriage bolt (F) through the  
height adjustment handle, the star washer and the  
height adjustment strap. Assemble a 5/16" flat washer  
(K) and the plastic knob (X) onto the end of the bolt.  
STEP 10: (SEE FIGURE 11 AND 12)  
Turn a rear hopper tube so that the brace holes in the  
middle of the tube face down. Slide the tube through  
the two loops sewn to the top rear seam inside the  
hopper bag.  
INNER BAG LOOPS  
5/16" x 1"  
CARRIAGE BOLT (F)  
REAR HOPPER TUBE  
(brace holes on bottom)  
5/16" FLAT  
WASHER (K)  
FIGURE 11  
PLASTIC KNOB (X)  
Insert the two upper hopper side tubes through the  
STAR WASHER (L)  
(between strap and handle)  
stitched flaps on each side of the hopper bag.  
Assemble the ends of the rear hopper tube onto the  
ends of the upper hopper side tubes. Fasten together  
using plastic plugs (Z).  
FIGURE 10  
PLASTIC PLUG (Z)  
UPPER HOPPER  
SIDE TUBE  
FIGURE 12  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 12: (SEE FIGURE 15 AND 16)  
STEP 11: (SEE FIGURE 13 AND 14)  
Insert the bag frame strap into the stitched sleeve  
along the front edge of the bag bottom.  
Turn the second rear hopper tube so that the brace  
holes in the middle of the tube face up. Assemble  
the ends of the rear hopper tube onto the ends of the  
lower hopper side tubes. Fasten together using plastic  
plugs (Z).  
Assemble the bag frame strap to the lower hopper  
side tubes using two 1/4" x 1-1/8" clevis pins (P) and  
3/32" hair cotter pins (N).  
REAR HOPPER TUBE  
(brace holes on top)  
BAG FRAME STRAP  
3/32" HAIR  
COTTER PIN (N)  
1/4" x 1-1/8"  
CLEVIS PIN (P)  
PLASTIC PLUG (Z)  
LOWER  
HOPPER  
SIDE TUBE  
FIGURE 15  
FIGURE 13  
Place the assembled lower hopper tubes into the  
bottom of the hopper bag  
Attach the ends of the lower hopper side tubes to the  
inside of the upper hopper side tubes using two 3/8"  
x 1/2" clevis pins (O) inserted from the inside, and two  
3/32" hair cotter pins (N).  
Secure the bag corners around the lower hopper side  
tubes by snapping the bag flaps to the bag bottom on  
both sides.  
UPPER HOPPER  
SIDE TUBE  
3/32" HAIR  
COTTER PIN (N)  
FLAP  
SNAP  
LOWER HOPPER  
FIGURE 16  
SIDE TUBE  
3/8" x 1/2"  
CLEVIS PIN (O)  
HOPPER BAG  
BOTTOM  
FIGURE 14  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 13: (FIGURE 17)  
STEP 15: (SEE FIGURE 19 AND 20)  
Secure the rope to the top center of the hopper bag  
IMPORTANT: Do not over bend the support rods  
during the following step. Over bending will cause the  
steel rods to loose supporting tension.  
frame.  
Tip the hopper onto it's back to assemble the two  
hopper support rods. Place the ends of each rod into  
the upper and lower rear hopper tubes, bending the  
rod just enough to fit into the holes in the tubes.  
FLAP  
SNAP  
FIGURE 19  
To assemble the hopper bag to the sweeper, slide  
the ends of the bag arm tubes into the ends of the  
sweeper's hitch tubes and secure with two 1/4" x  
1-3/4" clevis pins (Q) and 3/32" hair cotter pins (N).  
FIGURE 17  
BAG ARM TUBE  
STEP 14: (FIGURE 18)  
Insert a 3/8" x 3" clevis pin (R) through the lower hole  
in each upper hopper side tube. Next assemble a bag  
arm tube onto each clevis pin and secure it with a  
3/32" hair cotter pin (N).  
1/4" x 1-3/4"  
CLEVIS PIN (Q)  
3/32" HAIR  
COTTER PIN (N)  
Assemble a vinyl cap (V) onto the end of each bag  
arm tube.  
3/32" HAIR  
COTTER PIN (N)  
LOWER HOLE  
3/8" x 3"  
CLEVIS PIN (R)  
VINYL CAP (V)  
BAG ARM TUBE  
FIGURE 20  
FIGURE 18  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 16: (SEE FIGURE 21, 22 AND 23)  
Place the tractor and sweeper on a flat level surface.  
Set the sweeper height adjustment handle to about  
the middle of its adjustment range.  
Attach the sweeper hitch brackets to the tractor hitch,  
arranging the 3/4" spacers so that the bottom of the  
sweeper bag is approximately level and 5" to 7" above  
the ground. See figure 22 for tractor hitches that are  
10" to 13" above the ground. See figure 23 for tractor  
hitches that are 8" to 10" above the ground.  
5" Min.  
IMPORTANT: For best performance, the bottom of the  
sweeper bag should be approximately level and 5" to 7"  
off the ground as shown in figure 21.  
FIGURE 21  
Tractor hitches with 10" to 13" ground clearance.  
Tractor hitches with 8" to 10" ground clearance.  
10"-13"  
8"-10"  
TRACTOR HITCH  
TRACTOR HITCH  
FIGURE 22  
FIGURE 23  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOWYOUR SWEEPER  
WINDSCREEN  
HOPPER  
ROPE  
BAG ARM  
TUBE  
HEIGHT  
ADJUSTMENT  
HANDLE  
HEIGHT  
ADJUSTMENT  
STRAP  
KNOB  
HEIGHT  
ADJUSTME  
STRAP  
HOPPER BAG  
HITCH  
BRACKETS  
Hopper Bag  
Hopper Rope  
Windscreen  
Collects grass clippings, leaves and debris.  
Permits dumping of hopper bag from driver's seat.  
Helps prevent collected material from being blown out of hopper bag.  
Connects the hopper bag to the sweeper housing.  
Bag Arm Tubes  
Height Adjustment Handle  
Height Adjustment Strap  
Knob  
Adjusts the operating height of the sweeper.  
Holds the height adjustment handle in position when locked.  
Locks the height adjustment handle to the height adjustment strap.  
Connects the sweeper to the towing vehicle. Adjusts for various height tractor hitches.  
Hitch Bracket  
HOW TO USEYOUR SWEEPER  
BRUSH HEIGHT ADJUSTMENT  
DUMPING OF SWEEPER  
Your sweeper can be dumped easily without getting  
off of the rider or tractor. Simply pull the rope forward  
to dump the hopper. Always empty hopper after each  
use.  
To adjust your sweeper brushes to the best operating  
height, loosen the adjustment knob and push down on  
the height adjustment lever to raise the brush, or push  
up on the lever to lower the brush. See figure 22. Best  
adjustment is when the brush setting is 1/2" down into  
the grass. Always mow the grass to an even height  
before sweeping.  
CAUTION: Never attach the hopper rope  
to any part of your body or clothing! Never  
hold onto the rope while towing the sweeper!  
Attach the rope to the towing vehicle to keep  
it away from wheels and rotating parts.  
SWEEPING SPEED  
Try a starting speed of approximately 3 m.p.h. (third  
gear on most tractors). Depending on the conditions,  
it may be necessary to adjust the sweeping speed in  
order to achieve best results.  
CAUTION: Keep sweeper away from fire.  
Excessive heat can damage the brushes and  
hopper bag and could cause the bag and its  
contents to burn.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
CUSTOMER RESPONSIBILITIES  
Read and follow the maintenance schedule and the  
procedures listed in the maintenance section.  
MAINTENANCE SCHEDULE  
Fill in dates as you  
complete regular service.  
Service Dates  
Check for loose fasteners  
Check for worn or damaged parts  
Lubricate brush shaft bearings  
Lubricate wheel bearings  
X
X
X
X
X
Clean Sweeper  
X
X
Clean/Lubricate chain and sprockets  
X
SCHEDULED MAINTENANCE  
Clean the sweeper after each use.  
Inspect for worn or damaged parts, such as brushes  
and wheels.  
Lubricate the brush shaft bearing twice a year with a  
few drops of light weight oil. See figure 24.  
HEX BOLT  
SPACER  
FLAT WASHER  
FLAT WASHER  
HUB CAP  
HEIGHT ADJUSTMENT SLOT  
OIL BEARINGS HERE  
FLAT WASHER  
HEX LOCK NUT  
FIGURE 25  
HEX BOLT  
FIGURE 24  
CLEANING  
Every two years, remove the wheels and clean the  
gears found inside the wheel housing. After cleaning,  
lubricate the gears with an even coat of light grease.  
To remove the wheel, pop off the hub cap and remove  
the lock nut and flat washer. See figure 25.  
Clean sweeper housing with a soft brush or cloth.  
Clean debris from hopper bag with a brush or broom.  
Remove any material which has wrapped around  
brushes or ends of brush shaft.  
STORAGE  
Clean the sweeper and hopper bag thoroughly to help  
prevent rust and mildew.  
To collapse the hopper bag for storage, remove the two  
hopper support rods from the rear of the hopper.  
Store in a dry area.  
CAUTION: Before storing the sweeper,  
always empty the hopper bag to avoid  
spontaneous combustion.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WHEEL GEAR AND PAWL SERVICE  
BRUSH REPLACEMENT  
IMPORTANT: Do not remove both wheels at the same  
time to avoid mixing of parts. (The R.H. and L.H. ratchet  
sprockets are not interchangeable.) Make notes on the  
position of washers and snap rings during disassembly.  
NOTE: Brush replacement should be done one brush at  
a time.  
Remove the hopper bag from the sweeper.  
Loosen the hex bolts and lock nuts on two single  
brush retainers which clamp one brush to the double  
brush retainers. Do Not loosen or remove the bolts  
which fasten the double brush retainers to the brush  
shaft. See figure 26.  
Remove only one wheel from the sweeper.  
Remove the retaining rings and washers which hold  
the ratchet gear on the brush shaft.  
Slide the gear off of the brush shaft. (Look for the  
drive pin, which may fall out of the brush shaft when  
the ratchet gear is removed.) See figure 27.  
To reassemble, insert the drive pin through the hole  
near the end of the brush shaft. Make sure the pin  
slides back and forth easily in the shaft.  
Lightly grease the shaft and fill the ratchet gear with  
grease. Assemble the ratchet gear back onto the  
shaft.  
Lightly grease the axle and the gear teeth on the  
wheel, and then reassemble the wheel. The brushes  
should rotate only during forward rotation of the  
wheel. If the brushes are driven (rotated) by both  
forward and reverse rotation of the wheel, the drive  
pin is jamming in the ratchet gear. Disassemble to  
clean and lubricate the drive pin and the ratchet gear.  
Remove the second wheel and repeat the procedure.  
Slide the brush out of the retainers, noting on which  
side of the brush the bristles overlap. See figure 26.  
Install new brush, making sure the bristles overlap on  
the same side of the brush as before. See figure 26.  
BRUSH ROTATION  
OVERLAP  
BRISTLES  
BRUSH  
SHAFT  
SINGLE  
BRUSH  
RETAINERS  
DOUBLE BRUSH RETAINER  
OVERLAP  
BRISTLES  
RATCHET  
GEAR  
BRUSH ROTATION  
FIGURE 26  
DRIVE  
PIN  
FIGURE 27  
TROUBLESHOOTING  
Wheels skid when sweeping.  
Brushes set too low.  
Adjust height till brushes are 1/2"  
down into grass.  
Brushes are jammed  
Wheels are jammed.  
Stop sweeper. Remove obstruction.  
Remove one wheel at a time to check  
for obstruction or damage. Refer to  
Service and Adjustments section.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS  
REPAIR PARTS FOR MODEL 486.242211 - 42" LAWNSWEEPER  
45  
44  
47  
53  
59  
52  
49  
51  
47  
66  
44  
58  
66  
53  
46  
66  
58  
45  
66  
50  
59  
48  
20  
72  
46  
60  
61  
21  
61  
26  
43  
25  
24  
C
22  
42  
10  
23  
29  
25  
9
65  
18  
12  
D
29  
17  
19  
70  
C
38  
A
16  
1
14  
35  
A
68  
13  
3
39  
11  
39  
69  
7
69  
32  
62  
15  
35  
57  
B
36  
63  
29  
43  
71  
37  
69  
67  
54  
34  
27  
41  
29  
66  
55  
4
31  
33  
30  
D
60  
2
26  
56  
5
29  
29  
B
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS FOR MODEL 486.242211, 42" LAWNSWEEPER  
REF PART NO. qTY DESCRIPTION  
REF PART NO. qTY DESCRIPTION  
1
2
3
4
5
40614  
40615  
23353  
23368  
43343  
C-9M5732  
43182  
66137  
23336  
66070  
43063  
25408  
43840  
44732  
1
1
1
2
1
8
4
1
2
1
2
1
1
1
2
2
2
1
4
8
Hitch Tube, R.H.  
Hitch Tube, L.H.  
Pin, Hitch  
Tube, Hitch Spacer  
Hairpin Cotter, 1/8" #4  
Rivet, Pop  
Bolt, Hex 5/16-18 x 3/4"  
Sweeper Housing Assembly  
Washer, Special  
39  
40  
41  
42  
43  
44  
45  
46  
47  
23400  
48652  
48651  
43661  
64559  
48587  
48466  
48726  
48402  
48388  
48366  
24949  
43926  
43737  
44481  
24979  
23687  
24192  
26243  
40621  
43513  
44985  
45088  
44292  
44180  
43681  
43055  
43720  
44326  
43081  
43943  
46867  
48365  
40637  
3
1
1
4
2
2
2
2
4
1
2
1
2
1
2
1
1
1
1
2
2
2
4
2
2
4
8
1
1
4
1
2
2
1
Bushing, Pivot  
Gear, Pinion R.H. (not shown)  
Gear, Pinion L.H.  
Bolt, Hex 1/4-20 x 1" Lg.  
Ass'y, Dust Cover  
Tube, Hopper Frame (Rear)  
Tube, Upper Hopper Frame (Front)  
Tube, Lower Hopper Frame (Front)  
Plastic Plug  
Hopper Bag  
Clevis Pin, 3/8" x 1/2"  
Strap, Bag Frame  
Rod, Hopper Support  
Hopper Rope  
Cap, Vinyl  
Strap, Height Adjustment  
Bracket, Hitch  
Bracket, Hitch (Straight)  
Handle, Height Adjustment  
Tube, Bag Arm  
Pin, Clevis 3/8" x 3"  
Wheel & Tire Ass'y. (with bearings)  
Wheel Bearing  
Bolt, Hex 5/16-18 x 2-1/2" Lg.  
Bolt, Hex 5/16-18 x 2" Lg.  
Bolt, Carriage 5/16-18 x 1-1/2"  
Hairpin Cotter, 3/32" #3  
Knob, Wing 5/16-18 Thread  
Bolt, Carriage 5/16-18 x 1"  
Washer, Flat 5/16" Std. Wrt.  
Grip, Height Adjust  
7
9
10  
11  
12  
13  
14  
15  
16  
Height Adjustment Tube Assembly 48  
Bolt, Hex 5/16-18 x 1"  
Bushing, Spacer  
Bolt, Hex 5/16-18 x 1-1/4"  
Washer, Star  
Washer, 5/8" SAE  
Retainer, Dust Cover  
Bushing, Brush Shaft  
Brush Shaft  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
65  
17 R19212113  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
1629-56  
44910  
25850  
48557  
43012  
47189  
23580  
23581  
44008  
47046  
47810  
44911  
44006  
46219  
1650-21  
40001  
141  
Brush  
Bolt, Hex 1/4-20 x 3/4" Lg.  
12 Nut, Nylock 1/4-20  
4
8
2
2
Retainer, Brush (Double)  
Retainer, Brush (Single)  
Washer, Flat 1-1/8" x .78" x .025"  
Dowel Pin (Drive)  
15 Nut, Nylock 5/16-18  
2
2
2
2
6
4
2
2
2
Spacer, .39 I.D". x 1-1/4" O.D. x .5" 66  
Washer, Flat .849" x .598" x .025" 67  
Spacer, .78 I.D". x 1-1/4" O.D. x .5" 68  
Ring, Retaining .594"  
Washer, Shim 1-1/8" x .594" x .025" 70  
Washer, Flat 1-1/2" x .375" x .062" 71  
Nut, Nylock Jam 3/8-24 Thread  
Hub Cap  
Bolt, Hex 3/8-24 x 3-1/4" Lg.  
69  
Clevis Pin, 1/4" x 1-3/4" Lg.  
Clevis Pin, 1/4" x 1-1/8"  
Owners Manual  
1038  
2674-32  
44961  
72  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Get it fixed, at your home or ours!  
Your Home  
For repair – in your home – of all major brand appliances,  
lawn and garden equipment, or heating and cooling systems,  
no matter who made it, no matter who sold it!  
For the replacement parts, accessories and  
owner’s manuals that you need to do-it-yourself.  
For Sears professional installation of home appliances  
and items like garage door openers and water heaters.  
1-800-4-MY-HOME® (1-800-469-4663)  
Call anytime, day or night (U.S.A. and Canada)  
For expert home solutions advice: www.managemyhome.com  
Our Home  
For repair of carry-in items like vacuums, lawn equipment,  
and electronics, call or go on-line for the location of your nearest  
Sears Parts & Repair Service Center  
1-800-488-1222 (U.S.A.)  
1-800-469-4663 (Canada)  
Call anytime, day or night  
To purchase a protection agreement on a product serviced by Sears:  
1-800-827-6655 (U.S.A.)  
1-800-361-6665 (Canada)  
Para pedir servicio de reparación  
a domicilio, y para ordenar piezas:  
Au Canada pour service en français:  
1-800-LE-FOYERMC  
1-888-SU-HOGAR®  
(1-800-533-6937)  
(1-888-784-6427)  
® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC  
® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC  
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC  
© Sears Brands, LLC  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Black Decker Lawn Mower GRC730 User Manual
Bolens Lawn Mower 120 442R000 User Manual
Exmark Lawn Mower LZ27KC604 User Guide
Flymo Lawn Mower lawnrake User Guide
Land Pride Lawn Mower AT25 User Guide
Scag Power Equipment Lawn Mower SW36 12BS User Guide
Snapper Lawn Mower M280817B User Manual
Weed Eater Lawn Mower 159757 User Guide
Weed Eater Lawn Mower WE165T42A User Guide
Woods Equipment Lawn Mower CZ1736K User Guide