Billy Goat Lawn Mower PR550 User Manual

PR & OS Owner’s Manual  
Patent 6253416 and other patents pending  
BILLY GOAT POWER RAKE AND OVERSEEDER  
PR550, PR550H, OS552, OS552H  
Owner's Manual  
Accessories  
Replacement Parts  
SLICING REEL  
A complete verti-  
slicing reel for your  
PR. 20" wide reel for  
use in grasses that  
require vertical  
SLICING BLADES  
A full set of blades for  
replacement. Includes  
new lockwashers for  
replacement  
OVERSEEDER KIT  
The new light weight Plastic Overseeding  
Kit is constructed of durable High Density  
Polypropylene with two lift handles on  
each side to assist in lifting the entire unit  
and easily converts a PR Series Power  
Rake into an overseeder with 4 bolts and  
minimal tools.  
FLAIL SHAFTS  
FLAIL BLADES  
A complete set of  
our high quality flail  
blades for your PR.  
Includes new lock  
clips for  
A full set of shafts  
for replacement.  
Includes new lock  
clips for  
replacement  
installation.  
installation.  
cutting, and for  
assisting in lawn  
replacement  
installation.  
NOTE: Overseeder Conversion Kit  
(350328) includes Slicing Reel (350113).  
Part No. (350325) comes with the  
Overseeder Box only.  
overseeding projects.  
P/N 350187  
P/N 350325 / 350328  
P/N 350185  
P/N 350113  
P/N 350186  
Part No 350412  
Form No F061311C  
1
PR & OS Owner’s Manual  
Specifications  
PR550  
PR550H  
OS552  
OS552H  
Engine: HP  
5.5 (4.1 kW)  
5.5 (4.1 kW)  
5.5 (4.1 kW)  
5.5 (4.1 kW)  
Engine: Model  
Engine: Type  
12H1320118B8  
GX160T1QX2  
HONDA OHV  
12H1320118B8  
GX160T1QX2  
HONDA OHV  
B&S  
B&S  
VANGUARD  
VANGUARD  
Engine: Fuel Capacity  
Engine: Oil Capacity  
Total Unit Weight:  
Engine weight:  
3.0 qt. (2.84 L)  
0.66 qt. (0.62 L)  
149# (67.7 kg)  
36# (16.3 kg)  
15o  
3.88 qt. (3.6 L)  
0.69 qt. (0.65 L)  
147# (66.8 kg)  
34# (15.4 kg)  
20o  
3.0 qt. (2.84 L)  
0.66 qt. (0.62 L)  
162# (73.6 kg)  
36# (16.3 kg)  
15o  
3.88 qt. (3.6 L)  
0.69 qt. (0.65 L)  
160# (72.7 kg)  
34# (15.4 kg)  
15o  
Max. operating slope  
Sound test in accordance with  
2000/14/EC  
101 dB(a)  
101 dB(a)  
101 dB(a)  
101 dB(a)  
Sound at operators ear  
82 dB(a)  
82 dB(a)  
82 dB(a)  
3.2g  
82 dB(a)  
3.2g  
Vibration at operator position  
0.82g (8.04 m/s2)  
0.82g (8.04  
m/s2)  
SOUND  
SOUND LEVEL 82 dB(a) at Operators Position  
Sound tests were conducted in accordance with 2000/14/EC, and were performed on 2-13-2002 under the  
conditions listed below.  
Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on  
the unit for the sound power level for your model.  
General Conditions:  
Temperature:  
Wind Speed:  
Wind Direction:  
Humidity:  
Sunny  
48oF (8.9oC)  
2 mph (3.2 kmh)  
South East  
29%  
Barometric Pressure:  
30.34Hg (770 mm Hg)  
VIBRATION DATA  
VIBRATION LEVEL .82g (8.04m/s2)  
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using  
calibrated vibration test equipment. Tests were performed on 5-25-2006 under the conditions listed below.  
General Conditions:  
Temperature:  
Wind Speed:  
Wind Direction:  
Humidity:  
Sunny  
72.32oF (22.4oC)  
3.8 mph (6.12kph)  
East  
62.2%  
Barometric Pressure:  
29.9Hg (101.3kpa)  
Part No 350412  
Form No F061311C  
3
PR & OS Owner’s Manual  
INSTRUCTION LABELS  
®
The labels shown below were installed on your BILLY GOAT Power Rake/Overseeder. If any labels are damaged or missing, replace them  
before operating this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering  
replacement labels. The correct position for each label may be determined by referring to the Figure and Item numbers shown.  
LABEL DANGER KEEP HANDS  
AND FEET AWAY  
LABEL CLUTCH ITEM #49  
P/N 830503  
DANGER FLYING DEBRIS LABEL SPARK ARREST  
ITEM # 48 P/N 810736 ITEM #81 100252  
ITEM #51 P/N 400424  
LABEL CAUTION GUARDS  
ITEM #52 P/N 900327  
LABEL EXPLOSIVE FUEL  
ITEM # 50 P/N 400268  
LABEL INSTRUCTION HEIGHT ADJ.  
ITEM #35 P/N 350176  
LABEL INSTRUCTIONS SEEDER BOX  
ITEM #30 P/N 350386  
(page 15)  
LABEL SEED METERING  
ITEM #29 P/N 350392  
(page 15)  
ENGINE LABELS  
BRIGGS & STRATTON  
HONDA  
OIL ALERT  
WHEN OIL LEVELLOW,  
ENGINE STOPS IMMEDIATELY.  
ENGINE CONTROLS  
Honda  
Briggs & Stratton  
Set lever to choke when starting cold  
Throttle lever  
Choke lever  
Set lever to desired engine speed.  
Move lever completely to the left to  
stop engine  
Fuel valve  
Part No 350412  
Form No F061311C  
4
PR & OS Owner’s Manual  
PACKING CHECKLIST  
Your Billy Goat Power Rake is shipped from the factory in one carton, completely assembled.  
READ all safety instructions before assembling unit.  
TAKE CAUTION when removing the unit from the box the Handle Assembly is attached to the  
unit by cables.  
PUT OIL IN ENGINE BEFORE STARTING  
PARTS BAG &  
LITERATURE ASSY  
Warranty card P/N- 400972, Owner’s Manual P/N-350412, General Safety and Warnings Manual P/N-  
100295, Declaration of Conformity P/N-350139.  
Boxing Parts  
Checklist  
Briggs & Stratton  
5.5 B&S VANGUARD  
26  
28  
Honda 5.5 OHV  
Subaru 6HP EX17  
28  
28  
Literature Assy  
P/N-430334  
PR550, PR550H,  
PR550T, PR550HT,  
PR600S  
OS552, OS552H,  
and OS602S  
ASSEMBLY  
1. UNFOLD the upper handle (item 26) and slide handle lock loops (item 28) into place to secure the upper handle  
to the lower.  
2. CHECK engine oil level and fill to proper level with engine manufacturers recommended grade of oil. Move  
height adjust lever to down position, to level engine during checking. See engine manufacturers instruction  
manual.  
3. CONNECT spark plug wire.  
Part No 350412  
Form No F061311C  
5
PR & OS Owner’s Manual  
OPERATION  
FOLDING HANDLE  
This unit is equipped with a folding upper handle for easier storage and transportation. The handle can be folded by  
sliding the handle lock loops (item 28) up. This releases the upper handle, allowing it to be folded over the unit.  
counter clockwise  
to raise blades  
ADJUSTING BLADE DEPTH  
clockwise to  
The depth of the blades can be raised or lowered by rotating the knob on the top of  
lower blades  
the adjustment lever. The blades are lowered by rotating the knob clockwise, and  
raised by rotating the knob counter-clockwise. The relative depth of the blades can be  
gauged by using the depth scale located on the right front corner of the engine base.  
With new blades installed the depth can be estimated as follows: 2.5 on the scale is  
even with the ground, 3 is equal to 0.25" deep, and 3.5 is equal to 0.5" deep  
blades up  
transport  
blades up  
transport  
BLADE POSITION & DEPTH CONTROL LEVER  
The blades can be raised or lowered into the ground by height adjustment lever on the  
engine base. The height adjuster lock lever must be pushed back against the adjustment  
lever in order to lower the blades into the ground. The resulting blade depth can be  
adjusted higher or lower.  
See ADJUSTING BLADE DEPTH.  
blades down  
running  
SPRING TINE CONVERSION  
If are converting your Power rake to a spring tine reel, you will need to  
replace the spacer on the control lever to accommodate for the tine. First  
remove the clip (item 18), then unscrew the yoke (item 17), remove the  
washer (items 69) and insert the spacer (item 75) in front of the spring.  
Reassemble in reverse order.  
RAKING/SLICING TIPS  
Before beginning, it is best to evaluate the condition of the lawn by cutting one or more core  
samples from area to be treated. A core can be cut using a piece of pvc, or metal pipe.  
Hammer the pipe into the ground, remove it, push the core out of the pipe and inspect it to  
determine the depth of thatch in your yard.  
THATCH: Thatch is a dense layer of dead grass, clippings, and roots that builds up over time  
at the base of of the lawn preventing air, water, and fertilizer from reaching the soil. This can  
cause shallow root development and make a lawn more susceptible to drought and disease.  
Thatch also provides an ideal environment for insects to hide and multiply. Periodic removal of  
thatch will keep your lawn in good health.  
HEAVY THATCH: Lawns with an excessive amount of thatch will require multiple treatments  
for effective removal. Trying to remove excessive thatch (greater than 3/4"[19 mm] deep) in  
one treatment will damage or destroy the living part of the lawn. It is best to remove heavy  
thatch in seasonal treatments (i.e. spring, and fall).  
SLOPES: Rake slopes across not up and down. This is much easier and safer for the  
operator and is better for the lawn. Raking across will help to reduce runoff during watering  
and allow the sloped ground to hold more seed, fertilizer, and water. The units maximum  
operating slope is 35% or 19°.  
DEPTH: The wide range of depth adjustment on your unit is provided to allow for blade wear.  
Setting the reel deeper will not produce better, or quicker results. The flail reel is intended to  
be set so it just touches the surface on flat ground. The slicing reel should be set even with the  
ground for verti-slicing work, and set to a maximum 1/2" depth for overseeding jobs. Setting  
the reel deeper than this will only result in premature wear on the unit (i.e. failed belt). If you  
desire to work the ground deeper than the above guidelines allow, it should be done gradually  
in multiple passes..  
Fig. 1  
Fig. 2  
SLICING / OVERSEEDING: Mow the lawn to shorter than the normal cut height before  
starting (i.e. approximately 2" tall for fescue grass). For the best result, Slice/Overseed in criss-  
cross pattern (See Fig. 1 and See Fig 2).  
Part No 350412  
Form No F061311C  
6
PR & OS Owner’s Manual  
RAKING OPERATION-FLAIL REEL  
NOTE: Must have the flail reel assembly (350112) for this operation.  
MOW: Mow the lawn to it's normal cut height.  
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.  
SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat  
surface (i.e. driveway, or sidewalk).  
START ENGINE: See page 9 for further instruction.  
ENGAGE BLADES: Pull back on the bail on the operators handle. NOTE: When engaging the  
blades in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the  
operators handle lifting the front wheels slightly. Engage the blades. Slowly lower the unit into  
the turf.  
RAKE: Rake a small test area and examine the results. Thatch should be removed and  
deposited on top of the healthy grass. If excessive damage occurs to healthy grass, adjust the  
blade depth to decrease damage. Continue raking the yard, working in one direction (i.e.  
north-south, or east-west). NOTE: If a large drop in engine RPM occurs, or the unit pulls you  
forward and bounces during operation the blade depth is set too low.  
REMOVE THATCH: After raking, a layer of thatch will be deposited over the top of the lawn.  
This thatch must be removed prior to any fertilizing, seeding, or watering of the lawn. We  
suggest the use of a lawn vacuum or wheeled blower for collection and removal of the thatch.  
RAKING OPERATION-SPRING REEL  
NOTE: Must have the spring tine reel assembly (350354) for this operation.  
MOW: Mow the lawn to it’s normal cut height. Tall grass will not leave a manicured look when the  
dethatching job is complete.  
DRY: Be sure grass is relatively dry. Wet conditions can cause increased damage to healthy grass.  
SET DEPTH: With engine off, set the raking depth so that the spring tines are just above touching the  
flat surface (i.e. driveway, or sidewalk) the units height is being adjusted on. NOTE: Allowing the  
spring tines to have substantial contact with the ground will cause premature wear and failure of the  
spring tines.  
START ENGINE: See page 9 for further instruction.  
ENGAGE TINES: Pull back on the bail on the operators handle. NOTE: When engaging the spring  
tines in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators  
handle lifting the front wheels slightly. Engage the spring tines. Slowly lower the unit into the turf.  
RAKE: Rake a small test area and examine the results. Thatch should be removed and deposited on  
top of the healthy grass. If excessive damage occurs to healthy grass, adjust the spring tine depth to  
decrease damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west).  
NOTE: If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during  
operation the spring tine depth is set too low.  
REMOVE THATCH: After raking, a layer of thatch will be deposited over the top of the lawn. This  
thatch must be removed prior to any fertilizing, seeding, or watering of the lawn. We suggest the use  
of a lawn vacuum or wheeled blower for collection and removal of the thatch.  
VERTI-CUTTING OPERATION  
NOTE: Must have the slicing reel assembly (350113) for this operation.  
MOW: Mow the lawn to shorter than the normal cut height (approximately 2" tall)  
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.  
SET DEPTH: With engine off, set the raking depth so that the blades just touch on a flat surface  
(i.e. driveway, or sidewalk).  
START ENGINE: See Page 9.  
ENGAGE BLADES: Pull back on the bail on the operators handle. NOTE: When engaging the  
blades in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the  
operators handle lifting the front wheels slightly. Engage the blades. Slowly lower the unit into the  
turf.  
SLICE: Verti-cut a small test area and examine the results. Some thatch and cut stems should  
be removed and deposited on top of the healthy grass. Grass runners should be cut and ready  
for removal. If excessive damage occurs to healthy grass, adjust the blade depth to decrease  
damage. Continue raking the yard, working in one direction (i.e. north-south, or east-west).  
NOTE: If a large drop in engine RPM occurs, or the unit pulls you forward and bounces during  
operation the blade depth is set too low.  
REMOVE THATCH/STEMS: After verti-cutting, a layer of thatch and cut stems will be deposited  
over the top of the lawn. We suggest the use of a lawn vacuum or wheeled blower for collection  
and removal of the thatch/stems.  
Part No 350412  
Form No F061311C  
7
PR & OS Owner’s Manual  
OVERSEEDING OPERATION  
NOTE: Must have the slicing reel assembly (350113) for this operation.  
MOW: Mow the lawn to shorter than the normal cut height (approximately 2" tall)  
DRY: Be sure grass is dry. Wet conditions can cause increased damage to healthy grass.  
2
SEED: Spread grass seed according to the seed suppliers directions (e.g. 10 lbs. per 1000 ft [4.5  
2
kg. per 93 m ])  
SET DEPTH: With engine off, set the raking depth so that the blades reach 1/4"-1/2"(6-12 mm)  
below a flat surface (i.e. driveway, or sidewalk).  
START ENGINE: See Page 9.  
ENGAGE CLUTCH: Pull back on the bail on the operators handle. NOTE: When engaging the  
clutch in heavy load conditions (i.e. heavy thatch, or very uneven turf), push down on the operators  
handle lifting the front wheels slightly. Engage the clutch. Slowly lower the unit into the turf.  
SLICE: Run machine over the area that has been seeded to incorporate the seed into the soil. If  
excessive damage occurs to healthy grass, adjust the blade depth to decrease damage. Continue  
raking the yard, working in one direction (i.e. north-south, or east-west). NOTE: If a large drop in  
engine RPM occurs, or the unit pulls you forward and bounces during operation the blade depth is  
set too low.  
WATER/FERTILIZE: After the seed has been worked into the soil, water and fertilize according to  
the seed suppliers directions.  
ADJUSTING SEED RATE  
LAWN PREPARATION  
- MOW LAWN TO LOWEST SETTING ON  
YOUR MOWER.  
- DO NOT WATER PRIOR TO SEEDING.  
- POWER RAKE TO DETHATCH LAWN  
AND REMOVE THATCH.  
- FERTILIZE LAWN WITH BROADCAST  
SPREADER.  
LAWN PREPARATION  
- FOR BEST RESULTS OVERSEED IN  
TWO PASSES OF ONE-HALF  
APPLICATION RATE EACH, AT RIGHT  
ANGLES OR IN A CRISS-CROSS  
PATTERN.  
- WATER HEAVILY IMMEDIATELY THEN  
LIGHTLY FOR 10 - 14 DAYS, KEEPING  
SOIL MOIST.  
- AFTER GERMINATION, WATER LESS  
OFTEN TO PROMOTE ROOT GROWTH.  
Part No 350412  
Form No F061311C  
8
PR & OS Owner’s Manual  
MAINTENANCE  
PERIODIC MAINTENANCE  
Periodic maintenance should be performed at the following intervals:  
Maintenance Operation  
Inspect for loose, worn or damaged parts.  
Check engine oil  
Every Use (daily)  
Every 25 Hours  
z
z
z
z
z
Inspect belt  
Engine (See Engine Manual)  
Grease reel bearings  
z
Inspect and clean engine air filter  
Oil height adjustment linkage  
FLAIL BLADE WEAR  
1. Wait for engine to cool and disconnect spark plug.  
2. Close fuel valve on engine (if available).  
3. Lean unit back onto lower handles and secure in place.  
4. Inspect blades for wear, and immediately replace any bent or cracked blades. Measure the  
overall length of the blade. (See fig. 1)  
5. If blades measure less than 3.25"(83 mm) in overall length they must be replaced. NOTE: We  
recommend replacing all the flails at once.  
SLICING BLADE WEAR  
1. Wait for engine to cool and disconnect spark plug.  
2. Close fuel valve on engine (if available).  
3. Lean unit back onto lower handles and secure in place.  
4. Inspect blades for wear, and immediately replace any bent or cracked blades. Measure  
the overall length of the blade from the center of the attachment bolt to the tip of the worn  
blade.  
Fig. 1  
5. If blades measure less than 3"(76 mm) in length they must be replaced. NOTE: We  
recommend replacing all the blades at once.  
ROTATING FLAIL REEL END TO END  
To maximize flail blade life and performance the reel can be rotated end to end periodically to provide a fresh lead cutting edge. Takes approx. 20 min.  
and requires 1/2" and 9/16" socket wrenches with extension bar.  
1. Wait for engine to cool and disconnect spark plug.  
2. Close fuel valve on engine (if available).  
3. Lean unit back onto lower handles and secure in place.  
4. Remove (7) lock nuts (item 62 & 40) holding the belt and shaft guards (item 21 & 22) in place. It is necessary to lower the height adjust lever to reach  
the locknuts on the guards. Remove the guards.  
5. Remove the drive belt (item 9) by "walking" it out of the groove on the reel pulley (item 2).  
6. Remove the (4) lock nuts (item 60) and washers (item 68) holding the bearings (item 23) to the frame of the unit.  
7. The reel is now free from the machine. Slide the reel down and out of the machine.  
8. Remove the capscrew (item 71), lockwasher (item 57), reel pulley (item 2), key (item 42), and reel spacer (item 10) from the end of the reel.  
9. Rotate the reel end to end, and re-install these items on the opposite end of the reel.  
10. Re-install the reel in reverse order of removal. Re-install the guards in reverse order of removal.  
DRIVE BELT REPLACEMENT  
NOTE: Takes approx. 10 min. and requires 1/2" socket wrench with extension.  
1. Wait for engine to cool and disconnect spark plug.  
2. Remove (4) lock nuts (item 62) holding the belt guard (item 21) in place. It is necessary to lower the height adjust lever to reach the locknuts on the  
guard. Remove the guard.  
3. Remove the belt (item 9) by rotating the reel pulley (item 2) and walking it out of the groove. Discard old belt  
4. Install new belt using same procedure to walk the belt into the groove.  
5. With new belt installed pull bail rod back to engaged position and measure extension of idler spring. Spring should stretch 3/4" - 1" (19 25 mm) with  
bail engaged. Adjust clutch cable as necessary to achieve this extension.  
6. Re-install the belt guard.  
Part No 350412  
Form No F061311C  
9
PR & OS Owner’s Manual  
Troubleshooting  
Problem  
Possible Cause  
Solution  
Abnorm al vibration.  
· Dam aged or m issing blades. Loose  
handle bolts. Loose engine bolts  
· Stop work im m ediately. Replace any  
dam aged or m issing blades. Tighten all  
loose nuts and bolts.  
Engine stalls or labors when  
raking  
· Blades set too deep into ground.  
· Raise blades so that they just touch the  
ground on a level surface  
Engine will not start.  
· Stop switch off (Honda only). Throttle · Check choke position.  
in off position  
· O ut of gasoline or bad, old gasoline. · Check gasoline.  
· Spark Plug wire disconnected.  
· G as valve off.  
· Connect spark plug wire.  
· Turn on gas valve.  
· Dirty air cleaner.  
· Clean or replace air cleaner. Contact a  
qualified service person.  
Engine is locked, will not pull  
over.  
· Debris locked against reel, or drive  
pulleys. Engine problem .  
· Pull spark plug wire and rem ove debris.  
Contact an engine servicing dealer for  
engine problem s.  
Part No 350412  
Form No F061311C  
10  
PR & OS Owner’s Manual  
POWER RAKE SEEDER BOX KIT  
P/N 350395  
ITEM NO.  
23  
PART NO.  
8041026 SCREWCAP 5/16-18 x 3/4  
350372 BELT O-RING 5/16 X 15 9/16"  
8197031 PIN COTTER 1/8" X 1"  
9195106 ROLL PIN 1/8 - 1 1/4  
8172020 WASHER 5/16 FENDER  
8172007 WASHER 1/4 SAE  
DESCRIPTION  
QTY  
4
1
1
1
4
3
1
1
2
1
1
1
1
1
1
1
PARTS LIST  
ITEM NO.  
PART NO.  
350366  
350390  
350385  
350320  
350271  
350272  
350387  
350370  
8172009  
900321  
890108  
400217  
8024040  
8024021  
8123087  
8160001  
350389  
8160002  
8177011  
350369  
350280  
DESCRIPTION  
BOX AND LID ASSEMBLY  
QTY  
1
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
1
2
3
4
5
6
7
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
BRACKET CABLE MOUNTING  
CABLE SEED METERING ASSY  
SHAFT PLASTIC DROP SEEDER  
PLATE DOOR DROP SEEDER  
PLATE DOOR DROP SEEDER END  
PLATE DOOR DROP SEEDER END ARM  
PULLEY 3V GROOVE 0.625" BORE  
WASHER #10 3/8 SAE  
1
1
1
1
1
1
1
1
4
1
2
1
1
4
1
1
350392  
350386  
900230  
LABEL SEED METERING  
LABEL DROP SEEDER BOX  
WASHER 1/2 FC  
8161044 NUT LOCK 1/2" THIN HGT  
890456  
350313  
LABEL HOSE PLUG KD/SV  
LABEL PRODUCT DECAL OS  
BEARING CLIP 1.375 OD  
KNOB WING 5/16-18  
SPRING TENSION  
8024061 CARRIAGE BOLT 3/8-16 X 1 3/4"  
8024025 CARRIAGE BOLT 1/4-20 X 1 3/4"  
BOLT CARRIAGE 5/16 - 18 X 1  
BOLT CARRIAGE 1/4-20 X 3/4"  
SCREW SELF TAP #10-24 X 3/8" HMS ZP  
NUT LOCK 1/4  
BRACKET CABLE SEEDER BOX  
NUT LOCK 5/16  
WASHER LOCK 5/16  
PULLEY 3V GROOVE 1.530" BORE  
WASHER 0.906 O.D. X 0.656 I.D. X 0.062  
350399  
900471  
PIN CLEVIS .25 X .61  
PIN HAIR 1/4 ZP  
8160003 NUT LOCK 3/8-16 HEX  
8171004 WASHER 3/8 FC  
1
2
1
1
1
1
40  
41  
42  
43  
350391  
BRACKET MOUNTING METERING SEED  
1
4
1
7-8  
8059135 SCREW MACHINE #10-24 X 5/8  
8164005 NUT LOCK LT #10-24 HEX  
44  
900407  
TY-WRAP  
Part No 350412  
Form No F061311C  
11  
PR & OS Owner’s Manual  
FLAIL REEL KIT 350112  
PARTS DRAWING  
item  
no.  
QTY  
PARTS  
LIST  
Part No.  
8177012  
8171004  
8041050  
350141  
350100  
350144  
350145  
350146  
8172011  
1
1
1
57 LOCK WASHER 3/8 S/T MED  
68 WASHER 3/8 FLAT CUT  
71 SCREWCAP REEL PULLEY  
73 SHAFT FLAIL BLADE  
74 BLADE FLAIL  
76 SPACER BUMPER 5/8" x 1/2"  
77 SHAFT WA FLAIL REEL  
78 CLIP LOCK 1/2"  
4
30  
54  
1
8
8
79 WASHER 1/2 SAE  
FLAIL SHAFT KIT 350185  
FLAIL BLADE KIT 350186  
PARTS  
LIST  
Part No. QTY  
item  
no.  
PARTS  
LIST  
Part No. QTY  
item  
no.  
74 BLADE FLAIL  
350100 60  
73 SHAFT FLAIL BLADE  
78 CLIP LOCK 1/2"  
350141  
350146  
4
8
78 CLIP LOCK 1/2"  
350146  
8
SPACER BUMPER KIT 350258  
SLICING BLADE KIT 350187  
item  
no.  
PARTS  
LIST  
QTY  
item  
no.  
PARTSLIST  
QTY  
Part No.  
Part No.  
76 SPACER BUMPER 5/8" x 1/2"  
350144  
54  
81 BLADE 10" HEX SLICING  
350147  
20  
40  
40  
85 SCREWCAP 1/4-20 X 3/4 HCS ZP 8041004  
86 NUT LOCK 1/4-20  
8142004  
Part No 350412  
Form No F061311C  
12  
PR & OS Owner’s Manual  
SLICING REEL ASSY 350113  
PARTS DRAWING  
PARTS  
item  
no.  
57  
71  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
90  
PR500  
Part No.  
8177011  
400389  
350142  
350147  
350148  
350149  
350150  
8041004  
8142004  
350152  
350153  
350154  
350155  
QTY  
LIST  
LOCK WASHER 5/16 S/T MED  
SCREWCAP 5/16 - 24 x 1 1/4" HCS GR. 5  
SHAFT SLICING WA  
1
1
1
BLADE SLICING REEL  
PLATE BLADE MTG.  
20  
20  
10  
9
SPACER BLADE MTG.  
SPACER BLADE ASSY  
SCREWCAP 1/4-20 x 3/4, HCS ZP  
NUT LOCK 1/4-20  
40  
40  
1
COLLAR SPACER  
WASHER 0.937 x 1.750 x 0.119  
WASHER LOCK 7/8 INT. TOOTH  
NUT JAM 7/8"-14  
1
1
1
SPRING TINE REEL ASSY - 350355-S  
item  
Part No.  
QTY  
PARTS  
LIST  
no.  
1
2
3
4
SHAFT WA SPRING TINE REEL  
SHAFT SPRING TINE REEL  
SPRING TINE  
RING RETAINING 1/2"  
SCREWCAP3/8"-16 X 1" HCS ZP  
WASHER LOCK 3/8 S/T MED  
350353  
350351  
350352  
350146  
8041050  
8177012  
8171004  
1
4
108  
8
1
1
5
6
68 WASHER 3/8 FLAT CUT  
1
SPRING REPLACEMENT KIT - 350356-S  
item  
no.  
3
PARTS  
LIST  
QTY  
Part No.  
350352  
350146  
SPRING TINE  
RING RETAINING 1/2"  
108  
8
4
Part No 350412  
Form No F061311C  
13  
PR & OS Owner’s Manual  
PARTS DRAWING  
PR550, PR550H, OS552,  
OS552H,  
Part No 350412  
Form No F061311C  
14  
PR & OS Owner’s Manual  
PARTS LIST  
PARTS  
LIST  
PR550  
PR550H  
OS552  
OS552H  
item  
no.  
QTY  
QTY  
QTY  
QTY  
Part No.  
350101  
350411  
350102  
350103  
350104  
350107  
350112  
350114  
350115  
350116  
Part No.  
350101  
350411  
350102  
350103  
350104  
350107  
350112  
350114  
350115  
350116  
Part No.  
350101  
350411  
350102  
350103  
350104  
350107  
350113  
350114  
350115  
350116  
Part No.  
350101  
350411  
350102  
350103  
350104  
350107  
350113  
350114  
350115  
350116  
1 Pulley 3" OD  
1A Spacer 1" OD X .75" x .45 THK  
1
1
1
2
2
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
2
3
4
5
6
7
8
9
10  
Pulley 6.5" OD X ¾"  
WHEEL 8.0" X 5/8" BEARING  
WHEEL 10.0" X 5/8" BEARING  
Height Adjust Assy  
Reel Flail / Slicing / Spring Assy  
Pulley Idler 2.75"  
ArmIdler WA  
Belt 5L X 36  
11 Bracket Mount Clutch Cable  
12 Chassis WA W/ Label  
13 Frame Front WA  
350119  
350194  
350121  
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
-
350119  
350194  
350121  
350309  
350125  
350126  
350127  
350128  
350182  
350130  
350384  
350196  
350133  
350134  
350135  
350375  
350374  
350138  
350167  
350168  
350171  
350173  
350174  
350175  
350176  
350178  
350179  
350408  
500114  
600115  
-
9201078  
400570  
500181  
-
350193  
350301  
810736  
830503  
-
400424  
900327  
890132  
8024061  
8024043  
8024039  
8177012  
-
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
-
2
2
1
-
1
1
1
1
-
2
1
2
4
2
4
1
-
350119  
350194  
350121  
350309  
350125  
350126  
350127  
350128  
350182  
350130  
350384  
350196  
350133  
350134  
350135  
350375  
350374  
350138  
350167  
350168  
350171  
350173  
350174  
350175  
350176  
350178  
350179  
350408  
500114  
-
350379  
9201078  
400570  
500181  
350288  
350193  
350301  
810736  
830503  
100261  
400424  
900327  
890132  
8024061  
8024043  
8024039  
-
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
-
1
2
2
1
1
1
1
1
1
1
2
1
2
4
2
5
-
350119  
350194  
350121  
350309  
350125  
350126  
350127  
350128  
350182  
350130  
350384  
350196  
350133  
350134  
350135  
350375  
350374  
350138  
350167  
350168  
350171  
350173  
350174  
350175  
350176  
350178  
350179  
350408  
500114  
600115  
-
9201078  
400570  
500181  
350288  
350193  
350301  
810736  
830503  
-
400424  
900327  
890132  
8024061  
8024043  
8024039  
-
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
1
1
1
1
1
-
2
2
1
1
1
1
1
1
-
2
1
2
4
2
5
-
14 Bushing 0.375 OD X 0.256 ID X 0.88 350309  
15 Spring Height Adjust PR500  
16 Link Height Adjust PR500  
17 Yoke ½ - 20  
350125  
350126  
350127  
350128  
350182  
350130  
350384  
350196  
350133  
350134  
350135  
350375  
350374  
350138  
350167  
350168  
350171  
350173  
350174  
350175  
350176  
350178  
350179  
350408  
500114  
-
18 Pin Yoke ½"  
19 Bracket Mount Hgt. Adj. WA  
20 Spacer Spanner Wheel PR500  
21 Guard Belt WA W/ Label  
22 Guard Shaft WA W/ Label  
23 Bearing ¾" Cast Pillow Block  
24 Handle Lower LH WA  
25 Handle Lower RH WA  
26 Handle Upper PR500  
27 Bail Clutch WA  
28 Loop Folding Handle  
29 Deflector Rubber  
30 Shield Bearing  
31 Bar Clamp Deflector  
32 Bracket Height Adjust Lock WA  
33 Guard Pulley Back  
34 Lever Height Control  
35 Label Instr. Hgt. Adj.  
36 Bolt Shoulder ¼" x 1 ¾"  
37 Bolt Shoulder 5/16" x 1 ¾"  
38 Cable Clutch PR  
40 BOLT SHOULDER 1/2" X 1"  
41 ENGINE HONDA 5.5 H.P. GX160  
ENGINE 5.5 HP B&S VANGUARD  
42 KEY 3/16" X 1"  
350379  
9201078  
400570  
500181  
-
1
2
2
1
-
43 GRIP 1" x 13"  
44 GRIP LEVER 1/8 x 1 x 5"  
45 LABEL INSTRUCTION SEEDER BOX  
46 LABEL PRODUCT DECAL OVAL  
47 FINGER BELT WIRE  
48 LABEL DANGER THROWN OBJECT  
49 LABEL CLUTCH VQ  
50 LABEL WARNING FUEL EN/SP  
51 LABEL WARNING  
52 LABEL DANGER GUARD  
53 PLUG CAP 1" RD  
54 BOLT CARRAIGE 3/8-16 x 1 3/4  
55 BOLT CARRAIGE 5/16-18 x 1 3/4  
56 BOLT CARRIAGE 5/16 -18 x 3/4  
57 WASHER LOCK 3/8" S/T MED  
WASHER LOCK 5/16" TW TOOTH  
58 NUT LOCK #10-24  
350193  
350301  
810736  
830503  
100261  
400424  
900327  
890132  
8024061  
8024043  
8024039  
8177012  
-
1
1
1
1
1
2
1
2
4
2
4
1
-
430298  
8164005  
8160001  
8160003  
1
1
5
12  
430298  
8164005  
8160001  
8160003  
1
1
5
12  
8164005  
8160001  
8160003  
1
2
12  
8164005  
8160001  
8160003  
1
2
12  
59 NUT LOCK 1/4-20  
60 NUT LOCK 3/8-16  
61  
62 NUT LOCK 5/16-18  
63 SCREWCAP 1/4-20 x 1 1/2  
64 SCREWCAP 3/8 - 16 x 1 3/4  
8160002  
8041008  
8041053  
15  
1
1
8160002  
8041008  
8041053  
15  
1
1
8160002  
8041008  
8041053  
16  
1
1
8160002  
8041008  
8041053  
16  
1
1
Part No 350412  
Form No F061311C  
15  
PR & OS Owner’s Manual  
PARTS  
LIST  
PR550  
Part No.  
PR550H  
Part No.  
OS552  
Part No.  
OS552H  
Part No.  
item  
no.  
QTY  
QTY  
QTY  
QTY  
65 SCREWCAP 5/16-24 x 3/4" GR.5  
65A Washer 3/4 SAE  
8042026  
8172015  
430298  
8041030  
400164  
8171004  
8172011  
8161044  
8041050  
350266  
520031  
791080  
2
5
1
4
1
9
2
4
1
4
2
2
8042026  
8172015  
430298  
8041030  
400164  
8171004  
8172011  
8161044  
8041050  
350266  
520031  
791080  
2
5
1
4
1
9
2
4
1
4
2
2
8042026  
8172015  
430298  
8041030  
400164  
8171004  
8172011  
8161044  
400164  
-
3
5
1
4
1
8
5
4
1
-
8042026  
8172015  
430298  
8041030  
400164  
8171004  
8172011  
8161044  
400164  
-
3
5
1
4
1
8
5
4
1
-
65B Washer 5/16 Twist Tooth  
66 SCREWCAP 5/16 - 18 x 1 1/2  
67 SCREWCAP 5/16-24 X 1  
68 WASHER 3/8 FLAT CUT  
69 WASHER 1/2 SAE ZP  
70 NUT LOCK 1/2" - 13 THIN HGT  
71 SCREWCAP REEL PULLEY  
72 BUTTON SOCKET 5/16-18X5/8”  
73 BOLT SHOULDER 1/2" x 2"  
74 FLANGESCREW 0.375 -16 X 0.75  
75 SPACER 1/2" ID X 3/4"  
520031  
791080  
2
2
520031  
791080  
2
2
-
-
-
-
-
-
-
-
76 WASHER 3/8 SAE  
77 NUT PAL 3/8  
8172009  
360218  
8171002  
520119  
360279  
-
8172007  
890456  
-
2
2
5
2
2
-
1
1
-
8172009  
360218  
8171002  
520119  
360279  
100256  
8172007  
890456  
-
2
2
5
2
2
1
1
1
-
8172009  
360218  
8171002  
520119  
360279  
-
8172007  
890456  
441150  
8171003  
520116  
2
2
5
2
2
-
1
1
1
5
1
8172009  
360218  
8171002  
520119  
360279  
100256  
8172007  
890456  
441150  
8171003  
520116  
2
2
5
2
2
1
1
1
1
5
1
78 WASHER 1/4 FLAT CUT  
79 PIN CLEVIS 3/8" X 1.625  
80 RETAINER 3/8" BOLT PUSH NUT  
81 LABEL SPARK ARRESTOR EN/SP  
82 WASHER 1/4 SAE  
83 LABEL LOGO PRODUCT SM CIRCLE  
90 WASHER 1.125" OD X .344 ID X .25 THK  
100 WASHER FLAT 5/16"  
8171003  
520116  
5
1
8171003  
520116  
5
1
104 LABEL MADE IN U.S.A.  
Part No 350412  
Form No F061311C  
16  

Cub Cadet Lawn Mower 19A70001000 User Guide
Go Power Lawn Mower Manual User Manual
Husqvarna Lawn Mower Accessory H346SL User Guide
Hustler Turf Lawn Mower Trimstar Hydro Walkbehind User Guide
JVC Lawn Mower RX 7022VSL User Guide
Land Pride Lawn Mower FPS User Guide
Poulan Lawn Mower 180200 User Guide
Sears Lawn Mower 9172566 User Guide
Snapper Lawn Mower RLT125G38AKV User Manual
Snapper Lawn Sweeper 1695064 User Manual