FM Owner’s Manual
BILLY GOAT FINISH MOWER
Owner's Manual
FM3301EB
Patent Number: D494985
Accessories
Transaxle Guard
Kit
Grass Catcher Kit
Mulching Kit
To protect the
transaxle from
accidental contact
from concrete
curbs or other
hazards.
Easily convert your
mower to bag
grass and leaves.
Reduces lawn
clippings to fine
nutrient-rich
particles that filter
down to the soil.
P/N 520144
P/N 520142
P/N 520155
Part No 520187
Form No F010408A
1
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
SERIAL PLATE DATA
Record the model number, serial number, date of
purchase, and where purchased.
Purchase Date:
Purchased From:
Specifications
FM3301EB
Engine: HP
13 (9.7 kW)
Engine: Model
21A9070147
B & S INTEK OHV Elec.
3.0 qt. (2.8 L)
1.5 qt. (1.4 L)
267# (121 Kg)
15o
Engine: Type
Engine: Fuel Capacity
Engine: Oil Capacity
Total Unit Weight:
Max. operating slope
Overall length
57” (1.44m)
43” (1.09m)
47” (1.19m)
108dBa
Overall width
Overall height
In accordance with 2000/14/EEC
Sound at operators position
Vibration at operator position
88dBa
2.65g
Part No 520187
Form No F010408A
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
GENERAL SAFETY INSTRUCTIONS and SYMBOLS
The safety symbols shown below are used throughout this manual. You should become familiar with them before
assembling, operating, or servicing this equipment.
This symbol indicates important information that will prevent injury to yourself or others.
This symbol indicates ear protection is recommended when operating this equipment.
This symbol indicates eye protection is recommended when operating this equipment.
This symbol indicates gloves should be worn when servicing this equipment.
This symbol indicates that this manual and the engine manufacturer’s manual should be read
carefully before assembling, operation, or servicing this equipment.
This symbol indicates important information that will prevent damage to your BILLY GOAT ®
FM Mower.
This symbol indicates the engine oil level should be checked before operating this
equipment.
Read and make sure you thoroughly understand the following safety precautions before assembling, operating or
servicing this equipment:
READ this manual and the engine manufacturer’s manual carefully before assembling,
operating, or servicing this equipment.
EAR PROTECTION is recommended when operating this equipment.
EYE PROTECTION is recommended when operating this equipment.
BREATHING PROTECTION is recommended when operating this equipment.
EXHAUST from this product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
DO NOT operate this equipment on any unimproved forested, brushy, or grass covered land
unless a spark arrester is installed on the muffler as required by Section 4442 of the
California Public Resources Code. The arrester must be maintained in good working order.
Other states may have similar laws. Federal laws apply on federal lands.
DO NOT run engine in an enclosed area. Exhaust gases contain carbon monoxide, an
odorless and possibly fatal poison.
Part No 520187
Form No F010408A
4
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
WARNING: IMPORTANT! This cutting machine is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury or death.
DO NOT run this equipment indoors or in any poorly ventilated area. Refueling outdoors is recommended.
DO NOT refuel this equipment while the engine is running. Allow engine to cool for at least two minutes before
refueling.
DO NOT store gasoline near an open flame.
DO NOT remove gas cap while engine is running.
DO NOT start or operate engine if strong odor of gasoline is present.
DO NOT start or operate engine if gasoline is spilled. Move equipment away from spill until gasoline has completely
evaporated.
DO NOT smoke while filling the fuel tank.
DO NOT check for spark with spark plug or spark plug wire removed. Use an approved spark tester.
DO NOT operate engine without a muffler. Inspect muffler periodically and replace if necessary. If equipped with
muffler deflector, inspect deflector periodically and replace if necessary.
DO NOT operate engine with grass, leaves or other combustible material near the muffler.
DO NOT touch muffler, cylinder, or cooling fins when hot. Contact with hot surfaces may cause severe burns.
DO NOT leave equipment unattended while in operation.
DO NOT park equipment on a steep grade or slope.
DO NOT operate equipment with bystanders in or near the work area.
DO NOT allow children to operate this equipment.
DO NOT operate equipment with guards removed.
DO NOT operate equipment near hot or burning debris or any toxic or explosive materials.
DO NOT operate equipment on slopes greater than specified in Specifications section of this manual.
DO NOT operate barefoot or wearing open sandals. Always wear substantial footwear
DO NOT place hands or feet underneath unit, or near any moving parts.
DO NOT pull mower backwards unless absolutely necessary
DO NOT operate the mower while under the influence of alcohol or drugs.
DO NOT operate mower in wet grass. Always be sure of your footing; keep a firm hold on the handle and walk; never
run.
DO NOT mow on wet grass. Reduced footing could cause slipping.
DO NOT mow near drop-offs, ditches, or embankments. The operator could lose footing or balance
DO NOT mow excessively steep slopes.
DO NOT change the engine governor setting or overspeed the engine.
ALWAYS Stop the blade(s) when crossing gravel drives, walks, or roads.
ALWAYS Shut the engine (motor) oft and wait until the blade comes to complete stop before removing grass catcher.
ALWAYS Mow only in daylight or good artificial light.
ALWAYS Disengage the self-propelled mechanism or drive clutch on mowers so equipped before starting the engine.
ALWAYS wear safety goggles or safety glasses with side shields
ALWAYS remove spark plug wire when servicing equipment to prevent accidental starting.
ALWAYS check fuel lines and fittings frequently for cracks or leaks. Replace if necessary.
ALWAYS store fuel in approved safety containers.
WARNING: Important
Remove all rocks, wire, string, etc. that can present a hazard during work prior to starting.
DO identify and mark all fixed objects to be avoided during work such as sprinkler heads, water valves, limbs, or
clothes line anchors, etc.
Part No 520187
Form No F010408A
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
SOUND
SOUND LEVEL 88 dB(a) at Operator Position
108 dB(a)
Sound tests were conducted in accordance with 2000/14/EEC, and were performed on 8-15-2003 under the
conditions listed below.
Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on
the unit for the sound power level for your model.
General Conditions:
Temperature:
Wind Speed:
Wind Direction:
Humidity:
Sunny
86oF (30oC)
2.4 mph (3.9 kmh)
South
57%
Barometric Pressure:
30.2Hg (767 mm Hg)
VIBRATION DATA
VIBRATION LEVEL 2.65g (25.20m/s2)
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using
calibrated vibration test equipment. Tests were performed on 5-26-2006 under the conditions listed below.
General Conditions:
Temperature:
Wind Speed:
Wind Direction:
Humidity:
Sunny
87.44oF (30.8oC)
3.1 mph (5.04kph)
South East
41.5%
Barometric Pressure:
29.89Hg (101.25kpa)
INTENDED USE
INTENDED USE: This unit is mainly designed for cutting grass. Some overgrown weeds, and taller grass may also
be cut. Be sure to inspect work area and machine before operating. Make sure that all operators of this equipment
are trained in general machine use and safety.
Part No 520187
Form No F010408A
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
INSTRUCTION LABELS
The labels shown below were installed on your BILLY GOAT ® FM Mower. If any labels are damaged or missing, replace them before operating
this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering replacement labels. The
correct position for each label may be determined by referring to the Figure and Item numbers shown.
LABEL DANGER KEEP HANDS LABEL PATENT FM
DANGER FLYING DEBRIS LABEL CLUTCH BLADE LABEL CLUTCH DRIVE
ITEM #2 P/N 810736 ITEM #11 P/N 500177 ITEM #10 P/N 500176
AND FEET AWAY
ITEM#178 P/N520191
ITEM #5 P/N 400424
LABEL WARNING GUARDS
ITEM #119 P/N 900327
LABEL EXPLOSIVE FUEL
ITEM #4 P/N 400268
LABEL CUTTING HEIGHT
ITEM #95 P/N 520117
LABEL WARNING MOWER
ITEM #17 P/N 510206
LABEL HEIGHT ADJUST GUIDELINE
ITEM #7 P/N 520043
LABEL EAR EYE BREATHING
ITEM #114 P/N 890254
LABEL READ MANUAL
ITEM #52 P/N 890301
ENGINE LABELS
BRIGGS AND STRATTON
THROTTLE CONTROLS AND LABELS
Throttle Control
SPEED CONTROL
5th gear (Transporting Speed): Lift up
on the lever then push to engage in
the 5th gear.
Rev: Lift up on the lever then pull back
for reverse.
LABEL FM
CONSOLE ITEM #47
P/N 520079
ELECTRIC (520048)
Electric Start Only
Pull up on the switch then push
forward to start the engine.
Part No 520187
Form No F010408A
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
PACKING CHECKLIST
Your Billy Goat Mower is shipped from the factory in one crate, completely assembled except for the
handles and console assembly.
READ all safety instructions before assembling unit.
TAKE CAUTION when removing the unit from the box.
PUT OIL IN ENGINE BEFORE STARTING
PARTS BAG &
LITERATURE ASSY
Warranty card P/N- 400972, Owner’s Manual P/N-520187.
Boxing Parts
Checklist
Parts Bag
Briggs and
Stratton 6HP
Ty-wrap 900407 qty. 4
Washer 3/8 FC
8171004 qty. 4
Literature Assy
P/N-520137
8041051 qty. 4
Washer split lock 3/8"
8177012 qty. 4
Clevis pin 520119 qty. 1
Washer 5/16" FC
8171003 qty. 2
Roll pin 1/4"x1" long
520156 qty. 1
Pal Nut 3/8" 360218
qty. 1
Part No 520187
Form No F010408A
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
ASSEMBLY
NOTE: All item numbers called out in the assembly, operation, and
maintenance sections of this manual can be found on Parts List
(pages 15-18).
1. Cut and remove the nylon retaining straps (see figure 11-1).
2. With the console and handle assembly positioned as shown in
Figure 11-3, insert the shift linkage rod (Item 31) into the shift
linkage connector (Item 54).
3. To assemble the shift rod (item 31) to the shift linkage (item 54),
use the roll pin in the parts/literature bag. If you’ll notice on the shift
linkage, the hole is larger on one side than the other.
It will be easier to start the roll pin from the larger side, forcing it
through the shift rod and the hole on the other side of the shift
linkage, using a hammer or large adjustable pliers.
4. Insert one of the handle mounting bolts (Item 102) with split lock
washer (Item 6) on top of flat washer (Item 184) through the rear
handle mounting hole of the right side handle, and screw it into the
rear handle mounting hole on the right side of engine base chassis
(Item 61). Repeat this procedure for the left side using the left
handle.
Fig. 11-1
Shift rod
Shift
linkage
Roll Pin
5. On each side of the mower, insert one of the handle mounting
bolts (Item 102) with split lock washer (Item 6) on top of flat washer
(Item 184) through the hole in one end of the handle brace (Item
32), the front handle mounting hole of the handle and screw into the
front handle mounting hole in the engine base chassis (Figure 11-5).
6. Attach the blade lever using the clevis pin, two washers and the
pal nut from the parts bag. Align the lever to the hole on the handle
and place a washer on the pin and slide it through. Then put a
washer on the other side and gently tap the pal nut onto the end of
the pin. (See fig. 11-7)
Fig. 11-3
7. Position control cables and use 2 cable ties on each handle to
secure the cables in position. The top cable tie should be 1” below
the console and the lower tie should be 12” below the console (see
figure 11-8 and 11-9).
Fig. 11-4
Fig. 11-5
8. Check the position of the shift rod guide (Item 69), and if
necessary, snap it in place in the shift bracket (Item 78) as shown in
Figure 11-10.
9. Put shift lever in NEUTRAL, depress the brake lever (release the
brake) and carefully pull the machine back off the pallet.
10. Fill with oil and gas to the proper level and the unit is ready to
mow. (A battery will also have to be installed.)
11. Read the operator’s manual.
Fig. 11-7
Cable
ties
Fig. 11-8
Fig. 11-9
Fig. 11-10
Part No 520187
Form No F010408A
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
OPERATION
Like all mechanical tools, reasonable care must be used when operating machine.
Inspect machine work area and machine before operating. Make sure that all operators of this
equipment are trained in general machine use and safety.
PUT OIL IN ENGINE BEFORE STARTING
STARTING
ENGINE: See engine manufacturer’s instructions for type and amount of oil and gasoline used. Engine
must be level when checking and filling oil and gasoline.
ENGINE SPEED: Controlled by throttle lever on the control console plate.
FUEL VALVE: Move fuel valve to "ON" position (when provided on engine).
CHOKE: Operated with the throttle control by moving the throttle control to the full start position.
THROTTLE: Move remote throttle control to fast position. Pull starting rope to start engine.
ELECTRIC START: Choke the engine if necessary. Pull up then push forward on the toggle switch until
engine starts, then release switch to run.
1. Select desired cutting height before starting engine.
2. Be sure drive lever or blade lever are not engaged.
3. Choke if necessary.
4. Pull back on starter rope slowly until resistance is felt. Then pull cord rapidly to start. Repeat if necessary.
Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check for
damaged or worn blade, loose blade jam nut, loose engine or lodged foreign objects. Note: See maintenance section
for proper blade jam nut torque specifications.
HANDLING & TRANSPORTING:
Using two people to lift machine is recommended. Lift holding the handle and front of deck. Secure in place
during transport.
Never lift the machine while the engine is running. ENGINE MUST BE OFF while handling, lifting, or
transporting the unit on or off the vehicle.
STORAGE
Never store engine indoors or in enclosed poorly ventilated areas with fuel in tank, where fuel fumes may reach
an open flame, spark or pilot light, as on a furnace, water heater, clothes dryer or other gas appliance.
If engine is to be unused for 30 days or more, prepare as follows:
Be sure engine is cool. Do not smoke. Remove all gasoline from carburetor and fuel tank to prevent gum
deposits from forming on these parts and causing possible malfunction of engine. Drain fuel outdoors, into an
approved container, away from open flame. Run engine until fuel tank is empty and engine runs out of gasoline.
NOTE: Fuel stabilizer (such as Sta-Bil) is an acceptable alternative in minimizing the formation of fuel gum deposits
during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow mix ratio found on
stabilizer container. Run engine at least 10 min. after adding stabilizer to allow it to reach the carburetor.
CAUTION: Wheels must be chocked or blocked when unit is parked on a slope.
Part No 520187
Form No F010408A
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
CUTTING OPERATION
CAUTION: Shut off the blades when crossing gravel drives, walks or roads
and under all conditions where thrown objects might be a hazard.
CLEARING A CLOGGED CUTTING DECK: Turn engine off and wait for
blade to stop completely. Disconnect spark plug wire.
Wearing durable gloves, remove clog. Danger, the clog may contain
sharp materials. Reconnect spark plug wire.
Fig. 16-1
CAUTION: Use extreme care when operating the blades. Inspect the work
area for foreign objects that could cause damage to the unit or injure the
operator if struck by the blade. Never operate the blades with bystanders in the
work area.
GENERAL OPERATION: To engage the blades, depress the operator’s left
hand control lever against operator’s handle. The blade is disengaged by
releasing this lever. (See Fig. 1.1) To engage the wheel drive press down on
the brake lever, lift the operator’s right hand control lever against operator’s
handle. The drive is disengaged by releasing this lever.(See Fig. 1.2) Ground
speed can be varied by shifting gears as described on page 12. To begin
cutting, engage the blade lever, allow the blade to spin up to speed, and
engage the wheel drive to begin moving forward into the material to be cut.
NOTE: Do not engage blades during transport between work sites. The blade
should remain disengaged at all times when work is not being performed.
The best performance is achieved when cutting in dry conditions. If the deck
becomes choked with grass or debris during operation, back unit off of debris
allowing machine to clear itself and continue cutting, or shut the unit off and
clear the clog by hand (See above). A drop in engine RPM or a noticeable
change in engine sound is usually a good indicator of a clogged discharge or
other interference.
Fig. 16-2
Under most conditions cutting should be done in second or third gear. Fourth
gear should be reserved for conditions where grass is thinned out or not as tall.
The quality of the cut produced is directly related to the unit's ground speed
during cutting. If the quality of the cut is not satisfactory (i.e. material left
standing) you should shift into a lower gear during cutting. For improved control
in confined areas, this machine can be pushed forward or backward by
releasing the drive lever and shifting to neutral located at the bottom of the
operator's right-hand handle while depressing the brake release lever.
Fig. 16-3
CUTTING HEIGHT ADJUSTMENT
CAUTION: DO NOT make cutting height adjustment when engine is running.
Cutting height can be adjusted from 1.5" to 4" by placing spacers above or below
caster spindles. For easiest adjustment change the height on one side at a time.
To change cutting height, tilt the unit back, remove lynch pin, remove all spacers
then set if off to the side, remove caster rig, add or subtract spacers, reinstall
caster rig, place remainder of spacers if any, then reinsert lynch pin (see figure
16-1 through 16-4). Repeat this step on other side.
Fig. 16-4
NOTE: Be sure that the spacers are even on both casters. Running the deck out
of level will result in poor cut quality and increased belt wear.
Part No 520187
Form No F010408A
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
Blade Clutch Lever
BLADE CLUTCH
The FM mower blade clutch is controlled by an operator presence control. To
engage the blade, depress the operator’s left hand control lever against
operator’s handle. The blades are disengaged by releasing this lever. (See figure
16-5)
NOTE: The blade clutch must be either fully engaged for cutting or fully
disengaged to bring the blades to a stop. Do not operate the unit with the blade
clutch partially engaged. Premature belt wear and clutch failure will result from
improper operation of the clutch.
Operator’s
handle
CAUTION: Use extreme care when operating the blades. Inspect the work
area for foreign objects that could cause damage to the unit or injure the operator
if struck by the blade. Never operate the blades with bystanders in the work
area. Lever operates the blade without either the discharge deflector chute or the
grass catcher in place.
Fig. 16-5
Brake release lever
-down to release
Operator’s
handle
PROPULSION
This unit is self-propelled, and is controlled by an operator presence control. To
engage the wheel drive, first push down on the BRAKE RELEASE lever on the
right side, and then lift the operator's DRIVE lever on the right side against
operator's handle. The drive is disengaged by releasing the lower lever. (See
figure 16-6). Shift to neutral, push and hold the Brake lever to free wheel.
GROUND SPEED can be varied by selecting a higher or lower gear using the
gearshift lever on top of the console (see figure 16-7). Note: Only change gear
selection when unit is stopped. Under most conditions cutting should be done in
second or third gear. Fourth gear should be reserved for conditions where grass
is thinned out or not as tall. The quality of the cut produced is directly related to
the unit's ground speed during cutting. If the quality of the cut is not satisfactory
(i.e. material left standing), you should shift into a lower gear during cutting. For
improved control in confined areas, this machine can be pushed forward or
backward by releasing the drive lever located at the bottom of the operator's
right-hand handle, and shifting to neutral while depressing the brake release
lever.
Drive lever
-up to drive
Fig. 16-6
Fig. 16-7
HILLSIDE MOWING
WARNING! Never mow on any slope greater than 15 degrees. Always
mow across the face of slopes; never up and down or diagonally (see figure
16-8). DO NOT attempt sudden starts or stop when mowing on a slope.
Avoid sudden turns and use extreme caution when changing direction on a
slope.
Fig. 16-8
Part No 520187
Form No F010408A
12
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
MAINTENANCE
PERIODIC MAINTENANCE
Periodic maintenance should be performed at the following intervals:
Maintenance Operation
Every Use (daily) Every 5 hrs or (daily)
Every 25 Hrs
Every 50 Hrs
Every 200 Hrs
z
Inspect for loose, worn or damaged parts.
Check for excessive vibration
Inspect belt for wear
z
z
z
Engine (See Engine Manual)
Grease caster pivot points and lubricate height
adjustment spacers
z
z
Sharpen Blade
Lubricate pivot points of all three control levers
Check tire pressure
z
Note: inflate to mfr.’s specs. as shown on tire
side wall
z
z
Check brake puck
Check parking brake
z
Replace blade and traction belts
Note: Blade, blade brake puck, transaxle brake, and drive belts are normal wear items. These should be inspected
on a regular basis and replaced if worn.
BLADE Removal / Sharpening
NOTE: When sharpening the blade it is a good idea to check the balance of
the blade. A properly balanced blade will increase life of the bearings and other
components.
Tools required: ratchet, 3/4” inch socket, torque wrench, adequate support, block
to inhibit blade rotation.
1. Disconnect spark plug wire.
2. Support front of unit to allow access to the blades.
Note: Unit is heavy. Be sure support is adequate to prevent personal injury.
3. Block the blade to prevent it from rotating during removal (see figure 17-4).
For Each Spindle:
4. Remove the blade bolt (Item 35), lock washer (33), and large friction washer
(103).
Fig. 17-4
5. Remove the blade (18) and replace or sharpen the blade.
NOTE: Use only B.G.I. Part no. 520001(Standard blade) or B.G.I. Part no.
520002 (Mulch blade).
6. Reinstall the blade using all fasteners in the exact order they were removed
(see figure 17-4).
7. Torque blade screw to 60 ft-lbs.
NOTE: Before installing the fasteners inspect them for wear and replace as
necessary.
8. Reconnect spark plug wire.
Fig. 17-5
Part No 520187
Form No F010408A
13
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
BELT REPLACEMENT
When replacing one belt the other should be inspected for wear and replaced if worn. It
is good practice to change both belts when either is worn beyond use. Use only original
equipment belts for replacement. Billy Goat uses only premium quality, Kevlar corded
and coated belts in your unit. Substitute belts do not meet the design and performance
requirements for your unit, and will greatly reduce machine performance and belt life.
Blade Drive Belt
Tools required: ratchet, 3/4 inch socket, 10” extension bar for socket, two ½” wrenches
and adequate support for machine.
1. Disconnect spark plug wire.
2. Remove the deck belt cover.
3. Support front of unit to allow access to underside of the machine near the engine.
Note: Unit is heavy. Be sure support is adequate to prevent personal injury.
4. Observe the orientation of the belt fingers (Item 90) under the engine.
5. Remove the 4 engine mount bolts (Item 48) being careful not to let engine slide out
of place.
6. Remove the left and right belt fingers (These fingers are interchangeable).
7. Observe the orientation of the belt finger (Item 91) on idler (Item 50).
8. Loosen but do not remove idler/belt finger retaining nut (Item 144).
9. Observe belt routing and remove the belt from front spindle pulley (Item 46).
10. Remove the belt from the idler pulley and from the engine pulley.
11. Install new belt on engine pulley, idler and front spindle pulley following the original
belt routing.
Fig. 17-6
12. Position the idler belt finger centered on idler bracket and tighten the retaining nut
(Item 144).
13. Reinstall the left and right belt guide fingers under the engine base using all
fasteners in the exact order they were removed.
NOTE: Before installing the fasteners inspect them for wear and replace as necessary.
14. Torque the four engine bolts to 40 ft-lbs.
Note: With clutch levers engaged, be sure belt guides do not touch belts after
installation, there should be 1/8” clearance between the belt and the guides.
15. Observe the idler pulley when the blade drive lever is lowered and released (see
figure 17-7).
NOTE: Idler should tighten the belt when blade drive lever is pressed and the belt
should be slack when the lever is released. With the lever depressed, the edge of the
belt guide should not rub on the belt.
16. Replace the cover
17. Reconnect spark plug wire.
18. Start engine and check for proper operation of blade drive system.
Fig. 17-7
Spindle Drive Belt
Tools required: 3/8 inch socket, 1/2 inch socket.
1. Disconnect spark plug wire.
2. Follow steps to remove the Blade Drive Belt (on the spindle pulley side only) from the
previous section.
3. Loosen the two idler plate nuts (Item 143).
4. Slide the belt idler to release the belt tension.
5. Observe the belt routing, then remove the old belt and install the new belt using the
original routing.
6. Tension the belt using a long screwdriver or other pry bar to push the idler pulley
against the belt.
Note: Take care not to damage the idler pulley.
7.Tighten the two idler plate nuts just enough to avoid slippage while checking the belt
tension.
8. Check belt deflection. Finger pressure should give 0.5” to 0.75” (see figure 17-8).
9. Increase/decrease belt tension for proper deflection.
10. Finish tightening the two idler plate nuts.
11. Follow steps to reinstall Blade Drive Belt from the previous section.
12. Replace cover.
Fig. 17-8
13. Reconnect spark plug wire.
Part No 520187
Form No F010408A
14
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
BELT REPLACEMENT continued
Tools required: 1/2 Wrench or ratchet and 1/2 inch socket, adequate support for machine.
1. Remove the Blade Drive Belt (Steps 1-10: Blade Drive Belt Replacement Procedure).
2. Assure that spark plug wire is disconnected.
3. Support rear of unit to allow access to underside of the machine near the rear.
Note: Unit is heavy. Be sure support is adequate to prevent personal injury.
4. Observe the belt fingers (Item 63), position of idler and belt routing.
5. Remove the belt finger retaining nuts and bolts (Items 125 and 143).
6. Remove the belt finger and remove the belt from the transaxle pulley (Item 48).
7. Remove the belt from the drive idler (Item 105).
8. Remove the belt from the engine drive pulley (Item 85).
9. Install new belt on the top (small) engine pulley, drive idler and transaxle pulley using the
original belt position and routing.
10. Reposition and secure the belt finger (Item 63) using the original bolts, washers and nuts.
NOTE: Before installing the fasteners inspect them for wear and replace as necessary.
11. Reinstall the Blade Drive Belt (Steps 11-16: Blade Drive Belt Replacement Procedure).
Note: With clutch levers engaged, be sure belt guides do not touch belts after installation.
12. Replace the cover
Fig. 17-1
13. Reconnect spark plug wire.
14. Start engine and check both belts for proper operation of blade drive system and mower
drive system.
WARNING: If the drive belt begins to squeal or slip, do not continue to operate your unit
until adequate adjustment or repair has been performed. Improper adjustment can cause drive
belt to slip and overheat, greatly reducing machine performance and transmission life.
CABLE ADJUSTMENTS
Brake Adjustment
The brake control cable is spring-loaded and requires no adjustment; however, the transaxle
brake is adjustable. When the mower is in neutral and can be pushed by hand without
depressing the brake lever, the transaxle brake needs adjustment.
Using a ½ inch wrench turn the adjusting nut ¼ turn clockwise (see figure 17-1).
With the machine in neutral and:
Fig. 17-2
1. The brake lever not depressed, the brake should be on and inhibit the machine from being
rolled by pushing.
2. The brake lever depressed the brake should be off and the machine should roll uninhibited
by the brake.
Transaxle Drive Control Cable Adjustment
When the transaxle drive belt slips, the drive control cable needs to be adjusted or the belt
needs to be replaced with a new belt.
Cable Adjustment:
1. Using a 3/8” wrench, remove the rear access door (Item 51).
2. Using a ½ “ open end wrench, turn the inside adjusting nut counter-clockwise and back it off
1/8", then tighten the outboard adjusting nut against the support bracket (see figure 17-2).
3. Check for proper operation. If the operation is not correct, repeat step 2.
4. Replace the access door.
Fig. 17-3
The drive control cable adjustment should be the minimum amount required so the belt does
not slip when the drive is engaged.
Blade Drive Control Cable Adjustment
When the blade drive control lever is depressed, the blades should turn and the blade drive
belt should not slip. When the cable is properly adjusted the tension spring on the end of the
control cable will open slightly (only enough for a piece of paper to slip between the coils). See
figure 17-3.
Cable Adjustment:
1. Remove the deck belt cover (Item 81).
2. Observe the tension spring on the end of the cable when the blade drive lever is depressed.
The spring should just break open.
3. If adjustment is required, using a ½” open end wrench, turn the inboard adjustment nut
counter-clockwise and back it off 1/8" (Figure 4). Then tighten the outboard adjustment nut
against the cable support bracket (Item 49).
4. Check the spring tension with the blade drive lever depressed.
5. Readjust the control cable as needed for proper tension.
6. Replace the deck belt cover.
Note: Too much tension will shorten belt and bearing life and too little tension will allow the
belt to slip.
Part No 520187
Form No F010408A
15
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
BRAKE PUCK REPLACEMENT
Tools Required: 5/32” Allen wrench; 3/8” wrench.
1. Remove the spark plug wire.
2. Remove the belt deck cover.
3. Remove the brake spring (A) and control cable spring (B) (see figure 17-10).
4. Remove the blade drive belt (C) from the drive pulley (D).
5. Using a 3/8” wrench and 5/32” allen wrench, remove the
nuts from the #10 puck retaining bolts (see figure17-11).
6. Remove the bolts from the puck.
7. Remove the brake puck.
Fig. 17-9
Note: The puck ends are symmetrical and can be interchanged to use a new braking surface
unless both ends are already worn (Figure 4). When both ends have been used replace the
puck with a new one.
8. Inspect the nylon brake arm spacer (Item 44) by removing the belt finger (Item 91) and
idler pulley (Item 50).
9. Replace the spacer if it shows signs of wear.
10. Reassemble all parts in the same orientation as when removed.
A
B
Note: Be sure that the brake puck is centered and contacts both sides of the pulley groove
after tightening.
Note: Before installing fasteners, inspect them for wear and replace as necessary. Be sure
that when reinstalling control cable spring (B), the open side of the spring hook faces up.
11. Check the operation of the clutch and brake mechanism.
The drive belt should be slack and the brake engaged (center pulley will not turn easily by
hand) when no pressure is exerted on blade drive lever.
Note: When the blade drive lever is depressed, the brake puck should not rub on the center
pulley, the belt should be under tension, and not rub on the belt finger (see figure 17-10).
13. Replace the belt cover and connect the spark plug wire.
Start the engine and check the clutch/brake operation under power.
Fig. 17-10 Belt finger should
not rub on belt
D
C
when drive is
engaged.
Note: When the blade clutch control lever is pressed down, the blades should spin up to
speed without belt slippage indicated by a pronounced belt squealing sound. When the
clutch control lever is released, the blades should stop spinning in 5 seconds or less.
STARTER SWITCH WIRING
Fig. 17-11
Part No 520187
Form No F010408A
16
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
Troubleshooting
P r o b le m
P o s s ib le C a u s e
S o lu t io n
E n g in e w ill n o t s t a r t .
C h o k e n o t o n . O u t o f g a s o lin e , b a d o r o ld g a s . M o v e t h r o t t le t o s t a r t p o s it io n . C h e c k
S p a r k p lu g w ir e d is c o n n e c t e d . D ir t y a ir
c le a n e r . B la d e c lu t c h is e n g a g e d
G a s o lin e . C h e c k f o r s p a r k w it h a n
a p p r o v e d t e s t e r . C le a n o r r e p la c e a ir
c le a n e r . D is e n g a g e t h e B la d e c lu t c h
le v e r .
E n g in e w ill n o t s t o p
E n g in e r u n s p o o r ly
D a m a g e d c o n t r o l c a b le . H a r n e s s
d is c o n n e c t e d o r d a m a g e d . D a m a g e d ig n it io n
s w it c h .
W
ir e is
R e p la c e c o n t r o l c a b le . R e c o n n e c t
h a r n e s s w ir e o r r e p la c e if d a m a g e d .
R e p la c e s w it c h .
S p a r k p lu g w ir e lo o s e . E n g in e R P M s e t t o o
S h a r p e n o r r e p la c e b la d e ( p g 1 3 ) . C h e c k
lo w . C a r b u r e t o r o u t o f a d ju s t m e n t .
W
a t e r o r
e n g in e R P M ( r e f e r t o e n g in e
A d ju s t c a r b u r e t o r ( r e f e r t o e n g in e
a n u a l) . R e s e t g a p o r r e p la c e s p a r k
p lu g ( r e f e r t o e n g in e a n u a l) .
S t o p w o r k im m e d ia t e ly . C h e c k b la d e
o u n t a n d b a la n c e . R e p la c e d a m a g e d
o r b e n t b la d e if r e q u ir e d ( p g 1 3 ) . C h e c k
e n g in e o u n t .
m
a n u a l) .
d ir t in f u e l s y s t e m
w r o n g g a p
.
S p a r k p lu g f o u le d , f a u lt y o r
m
m
A b n o r m a l v ib r a t io n .
·
L o o s e o r o u t o f b a la n c e b la d e . B e n t b la d e .
L o o s e e n g in e b o lt s
m
m
U n e v e n c u t
H e ig h t a d ju s t is n o t s e t c o r r e c t ly . D u ll o r b e n t
b la d e . T ir e p r e s s u r e lo w o n o n e s id e .
B e s u r e h e ig h t a d ju s t is s e t t h e s a m e o n
b o t h s id e s ( p g 1 1 ) . S h a r p e n o r r e p la c e
b la d e ( p g 1 3 ) . A d ju s t p r e s s u r e .
W
ill n o t c u t o r h a s p o o r
D u ll o r b e n t B la d e . C lo g g e d d e c k . E n g in e
S h a r p e n o r r e p la c e b la d e ( p g 1 3 ) .
c u t t in g p e r f o r m a n c e
r u n n in g a t t o o lo w R P M .
E x c e s s iv e ly h ig h g r a s s .
W
e t G r a s s .
U n c lo g d e c k ( p g 1 1 ) . C h e c k e n g in e R P M
( r e f e r t o e n g in e m a n u a l) . D o n o t
w h e n g r a s s is w e t . M o w o n c e a t
m
a
o w
h ig h
c u t in g s e t t in g t h e n m o w a g a in a t d e s ir e d
s e t t in g o r m a k e n a r r o w e r c u t t in g p a t h .
a
B e lt s lip s o r s m o k e s
N o s e lf p r o p e llin g
B e lt t e n s io n t o o lo w . B e lt w o r n o r s t r e t c h e d .
P u lle y s w o r n o r d a m a g e d . C o n t r o l c a b le o u t o f b e lt . R e p la c e P u lle y s . A d ju s t c o n t r o l
a d ju s t m e n t .
I n c r e a s e t e n s io n a t id le r ( p g 1 4 ) . R e p la c e
c a b le
N o t s e t t o g e a r . O u t o f a d ju s t m e n t c lu t c h
S h if t le v e r t o d e s ir e d g e a r . A d ju s t c lu t c h
c a b le ( p g 1 5 ) . R e p la c e w it h n e w c a b le .
R e p la c e b e lt ( p g 1 4 ) .
c a b le . B r o k e n c lu t c h c a b le .
b e lt .
W
o r n o r b r o k e n
S e lf p r o p e lle d d r iv e w ill
n o t r e le a s e .
C lu t c h c a b le o u t o f a d ju s t m e n t . D a m a g e d
d r iv e c lu t c h le v e r .
A d ju s t c lu t c h c a b le ( p g 1 5 ) . R e p la c e
d r iv e c lu t c h le v e r .
E n g in e is lo c k e d , w ill n o t
p u ll o v e r .
D e b r is lo c k e d a g a in s t b la d e . D a m a g e d e n g in e . R e m o v e d e b r is ( p g 1 1 ) . R e f e r t o e n g in e
B r o k e n c o n t r o l c a b le . o w n e r 's m a n u a l. R e p la c e c o n t r o l c a b le .
When servicing engine refer to specific manufacturers engine owner's manual. All engine warranty is covered by the
specific engine manufacturer. If your engine requires warranty or other repair work contact your local servicing
engine dealer. When contacting a dealer for service it is a good idea to have your engine model number available
for reference(See table page 11). If you cannot locate a servicing dealer in your area you can contact the
manufacturers national service organization.
To reach: Briggs & Stratton: 800-233-3723
WARRANTY CLAIM PROCEDURE
®
Should a BILLY GOAT machine fail due to a defect in material and/or workmanship, the owner should make a
warranty claim as follows:
•
•
•
The machine must be taken to the dealer from whom it was purchased or to an authorized Servicing BILLY
GOAT Dealer.
The owner must present the remaining half of the Warranty Registration Card, or, if this is not available, the
invoice or receipt.
The Warranty Claim will be completed by the authorized BILLY GOAT Dealer and submitted to their
respective BILLY GOAT Distributor for their territory Attention: Service Manager. Any parts replaced under
warranty must be tagged and retained for 90 days. The model number and serial number of the unit must
be stated in the Warranty Claim.
•
•
The distributor service manager will sign off on the claim and submit it to BILLY GOAT for consideration.
The Technical Service Department at BILLY GOAT will study the claim and may request parts to be
returned for examination. BILLY GOAT will notify their conclusions to the distributor service manager from
whom the claim was received.
•
The decision by the Technical Service Department at BILLY GOAT to approve or reject a Warranty Claim is
final and binding.
For online product registration go to www.billygoat.com
Part No 520187
Form No F010408A
17
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
PARTS DRAWING FM
7
38
127
126
189
173
172
171
1
53
126
38
5
169
168
42
23
166
170
174
145
62
24
20
46
147
164
165
139
171
65
163
173
17
16
172
155
168
41
2
171
119
130
167
21
127
179
81
178
175
155
151
144
144
71
151
56
144
180
126
5
151
144
87
103
18
35
33
Part No 520187
Form No F010408A
18
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
PARTS LIST
FM3301EB
Part NO.
520184
ITEM
NO.
1
DESCRIPTION
QTY
BUSHING BRONZE
4
1
2
1
1
1
3
2
2
1
3
3
3
12
2
1
1
2
1
2
2
1
1
4
3
1
5
16
1
2
21
2
1
20
4
3
3
6
3
3
6
3
3
3
3
3
1
4
1
1
2
5
7
LABEL DANGER FLY
LABEL WARNING
810736
400424
520043
510205
510206
520001
520004
520005
520007
520008
520025
520028
520034
520041
520042
520047
520067-S
520071-S
520077
520081
520088
520100-S
520109
610308-P
900327
8024058
8024059
8041023
8041107
8160003
8160005
8160001
8171003
8172015
520008-01
520008-02
520008-03
520008-04
520008-05
520008-06
520008-07
520008-08
520008-09
520008-10
520008-11
520140
LABEL HGT. GUIDELINE
SPRING EXHAUST CHUTE
LABEL WARNING MOWER
BLADE 11.88”
LYNCH PIN 3/16” X 1 9/16
WHEEL AND TIRE 8” ASSY.
BELT SPINDLE DRIVE
SPINDLE ASSY FM
WASHER 1/2 INNER TOOTH
SCREW CAP 1/2-20X1.25
BUSHING CASTER SPACERS
SPACER FRONT CASTER
EXHAUST CHUTE DEFLECT.
PULLEY DECK FRONT DRIVE
CASTER ARM FM WA
DECK WA W/ LABELS
BRACKET CASTER FM WA
PLUG 3/8” BUTTON HEAD
WIRE BELT FINGER
16
17
18
20
21
23
24
33
35
38
41
42
46
53
56
62
65
71
81
87
GUARD BELT W/ LABELS FM
KNOB 3 PRONG 1/4”
103 WASHER 1/2” X 2
119 LABEL DANGER
126 BOLT CARRIAGE 3/8-16X1” ZP
127 BOLT CARRIAGE 3/8-X 1 1/4
130 SCREW CAP 1/4 - 20 X 7"
139 SCREW CAP 1/2-13 X 4 1/2
144 NUT 3/8-16 LOCK NYLON
145 NUT 1/2-13 LOCK NYLON
147 NUT 1/4-20 LOCK NYLON
151 WASHER 5/16” FC
155 WASHER 3/4 FC
163 HOUSING SPINDLE
164 SHAFT SPINDLE 1215 C. D. S.
165 BEARING BALL 6305-25
166 WASHER
167 SHIELD
168 RETAINING RING
169 RETAINING RING
170 WOODRUFF KEY # 605
171 PULLEY 4.75” DIA. 3/4” BORE
172 MACHINERY BUSHING 3/4”
173 NUT 3/4-16 NYLON HEX
174 FRONT CASTER ASSY.
175 BEARING CASTER WHEEL
178 LABEL BGI BIG CIRCLE
179 LABEL 33" CUT FM
520124
430303
520115
180 LABEL MADE IN USA
189 FITTING GREASE
520116
610363
1
2
Part No 520187
Form No F010408A
19
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
PARTS DRAWING FM
13
183
Battery is
included
190
151
123
143
89
40
96
IV
III
IV
III
II
I
II
192
104
140
I
4
91
144
151
37
151
147
50
44
178
102
116
83
51
184
55
137
36
58
151
36
148
143
187
6
9
120
138
151
59
86
29
137
144
125
184
83
49
143
181
93
92
159
85
6
144
150
144
102
118
90
151
137
111
109
106
Part No 520187
Form No F010408A
20
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
PARTS LIST
FM3301EB
Part NO.
400268
8177012
430298
520199
520018
520031
520032
520039
520045
520052
520061
520062
520070
520073
520074
520103
520105
520106
520111
520197
520113
520114
8041032
520118
8041051
790133
830114
850132
850443
890359
890408
900327
8024039
8024040
8041050
8041054
8160001
8160002
8160003
8161042
8155007
8171002
8171003
9201123
520191
8177011
8142002
520123
8171004
8171001
520182
520200
ITEM
NO.
4
6
9
DESCRIPTION
QTY
LABEL HOT ENGINE
1
4
2
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
4
1
1
1
1
2
3
1
2
1
4
1
2
3
6
1
2
1
8
1
1
1
1
1
4
2
1
1
WASHER SPLIT LOCK 3/8"
WASHER 5/16" TWISTED LK.
BATTERY BRACKET
SCREW SOCKET #10 X 1”
BOLT SHOULDER 1/2” X 2”
IDLER PLASTIC 4” X 0.375
ENGINE 13 HP B&S
SPACER NYLON BRAKE
BRKT CLUTCH CABLE FM
PULLEY IDLER BLADE DRIVE
PLATE ACCESS DOOR FM
BRKT IDLER DECK BLADE WA
PLATE BLADE CLUTCH IDL.
PLATE BLADE CLUTCH BK
SPRING TENSION WIRE
PULLEY DOUBLE 6 / 3.5 FM
BRAKE PUCK FM
CABLE BATTERY POS 10”
BRACKET BELT FINGER
BRACKET BELT FINGER BK.
SPACER HUB 1” BORE 1.5”
SCREWCAP 5/16” -18 x 2"
WIRE HARNESS
13
29
36
37
40
44
49
50
51
55
58
59
83
85
86
89
90
91
92
93
96
102 SCREWCAP 3/8” - 1.25”
104 CABLE BATTERY BLACK 10”
106 SCREWCAP 7/16 X 2 1/4 GR 8
109 WASHER LOCK 7/16 TWIST
111 WASHER ENGINE PULLEY
116 SCREW 1/4” - 20 X 5/8"
118 SCREWCAP 3/8” 1 1/2" TAP
120 LABEL GUARDS
123 BOLT CARRIAGE 1/4" X 3/4"
125 BOLT CARRIAGE 5/16" X 1"
137 SCREW CAP 3/8"-16 X 1 HEX
138 SCREW CAP 3/8"-16 X 2 HEX
140 NUT LOCK 1/4"-20 NYLON
143 NUT LOCK 5/16"-18 NYLON
144 NUT LOCK 3/8"-16 NYLON
147 NUTLOCK 3/8"-16 LW TH ZP
148 NUT LOCK #10
150 WASHER 1/4” FC
151 WASHER 5/16” FC
159 KEY 1/4” SQ. X 2.25" LONG
178 LABEL DESIGN PATENT FM
181 WASHER SPLIT LOCK 5/16"
182 NUT JAM 5/16"
183 POSITIVE CABLE 10"
184 WASHER 3/8" FLATCUT
187 WASHER #10 FLATCUT
190 VALVE OIL DRAIN
192 BATTERY 12v W/LABEL
Part No 520187
Form No F010408A
21
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
PARTS DRAWING FM
143
70
147
108
25
144
151
176
150
57
36
142
151
182
151
129
70
TO CONSOLE
124
105
127
142
143
73
BRAKE CABLE
132
61
39
150
63
27
110
160
54
125
101
112
141
150
BELT LAYOUT
157
152
48
105
19
156
48
ENGINE PULLEY
150
186
132
162
155
26
188
158
22
155
162
BLADE CLUTCH IDLER PULLEY
SPINDLE PULLEY
158
156
160
150
DECK DRIVE PULLEY
110
136
Part No 520187
Form No F010408A
22
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
PARTS LIST
FM3301EB
Part NO.
520201
520006
520009
520010
520016
520031
520037
520198
520068
520203
520177
520196
520087
520092
520156
800260
830526
850230
850408
8024023
8024042
8041053
8041013
8041029
8041035
8123128
8160001
8160002
8160003
8161042
8171002
8171003
8172007
8172015
8177011
8181007
9201087
850238
830177
8143001
8142002
850233
850238
ITEM
NO.
DESCRIPTION
QTY
19
22
25
26
27
36
39
48
54
57
61
63
70
73
BELT TRANS DRIVE FM
BELT BLADE DRIVE FM
SPRING TORSION WIRE
TRANSAXLE 5SPD FM
BRACKET T-AXLE SUPPORT
BOLT SHOULDER 1/2” X 2”
SPRING BRAKE
PULLEY 6.875 OD 4LV GROOVE 0.625 BORE
SHIFT LINKGAGE WA FM
BRKT IDLER GRND DRIVE
BASE ENGINE W/INSERTS
BRACKET BELT GUIDE DRV
GROMMET RUBBER 1”
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
2
1
1
2
1
1
1
4
1
2
4
1
1
5
3
1
6
5
1
2
2
2
2
2
1
1
GROMMET RUBBER 1.25”
101 ROLL PIN 1/4” X 1.0 IN LONG
105 PULLEY IDLER TENSION
108 TUBE PIVOT IDLER VQ
110 RING SNAP 0.75
112 SCREW CAP 1/4-28X1/2” GR 5
124 BOLT CARR. 1/4-20X1.25”
125 BOLT CARR. 5/16-18X1 1/2”
127 SCREWCAP 3/8-16 X 1 3/4
129 SCREWCAP 1/4"-20 X 2.75"
132 SCREWCAP 5/16-18 X 1.25"
136 SCREW CAP 5/16 - 18 x 2.75
141 SCREW SELF TAP 5/16
142 NUT LOCK 1/4-20 NYLON
143 NUT LOCK 5/16-18 NYLON
144 NUT LOCK 3/8-16 NYLON
147 NUTLOCK 3/8”-16 LW TH ZP
150 WASHER 1/4” FC
151 WASHER 5/16” FC
152 WASHER 1/4 SAE
155 WASHER 3/4 FC
156 WASHER LOCK 5/16 SPLIT
157 WASHER LOCK 1/4” EXT.
158 KEY 3/16 x 2 1/8
160 WASHER 3/4 THIN
162 WHEEL AND TIRE 13”
176 NUT JAM 1/4-20
182 NUT JAM 5/16
186 RING SNAP 5/8 T.A.
188 WASHER .765 ID X 1.25 OD X .06
Part No 520187
Form No F010408A
23
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
PARTS DRAWING FM
74
95
99
191
191
98
100
113
3
134
10
8
47
14
68
154
28
75
143
143
60
150
82
135
123
79
52
121
114
144
34
67
116
150
77
76
3
153
143
150
80
122
12
143
135
97
77
154
191
177
143
150
69
117
113
32
143
11
78
30
32
123
66
185
72
31
121
TO TRANS.
Part No 520187
Form No F010408A
24
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
PARTS LIST
FM3301EB
ITEM
NO.
3
DESCRIPTION
QTY
Part NO.
360218
430128
500176
500177
500267
500307
520017
520019
520179
520024
520026-S
520048
890301
520075
520083
520204
520085
500130
520091-S
520093-S
520094
520095
520096
520097
520098
520146
520102
520117
520119
520120
520121
520121
520122
890132
890254
890359
830513
900407
360203
8041032
8041033
8160002
8160003
8171002
8172008
8172011
520110
520176
8171003
PALNUTS 3/8”
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
2
1
4
1
6
1
4
9
2
12
2
2
1
1
4
8
KNOB 1/2” THREAD
LABEL CLUTCH DRIVE
LABEL BLADE DRIVE
10
11
12
14
28
30
31
32
34
47
52
60
66
67
68
69
82
74
75
76
77
78
79
80
82
95
97
98
99
GRIP HANDLE 1” x 7”
SWITCH ELECTRIC W/ NUT
SPRING COMPRESSOR 1/2”
CONTROL THROTTLE POS
ROD SHIFT LINKGAGE
BAR HANDLE BRACE FM
HANDLE RH FM
LABEL CONSOLE
LABEL READ MANUAL
SHIFT LOCK HANDLE FM WA
CABLE CLUTCH BLADE FM
CABLE CLUTCH DRIVE FM
CABLE CLUTCH BRAKE FM
BUSHING NYLON
HANDLE LH FM
LEVER CONTROL BRAKE FM
LEVER CONTROL DRIVE FM
LEVER CONTROL BLADE FM
PLATE REV LOCK OUT
BRACKET SHIFT PIVOT FM
GRIP LEVER ORANGE
CONSOLE FM W/ LABELS
CUP HOLDER
LABEL PUSH TO RELEASE
CLEVIS PINS 3/8 - 1.625
CLEVIS PINS 3/8 - 2.125
GRIP LEVER 0.125-1.00-3.75
100 GRIP LEVER 0.125-0.75X3.75
113 PLUG TUBE INSERT 1”
114 LABEL EAR-EYE-BREATHE
116 SCREW 1/4” - 20 X 5/8
117 PIN CLEVIS 5/16-24
121 TY-WRAP
122 PAL NUTS 5/16”
123 BOLT CARRIAGE 5/16-18 X 3/4
134 SCREW CAP 5/16-18 X 2
135 SCREWCAP 5/16-18 x 2 1/4
143 NUT LOCK 5/16-18 NYLON
144 NUT LOCK 3/8-16 NYLON
150 WASHER 1/4” FC
153 WASHER 5/16 SAE
154 WASHER 1/2” SAE ZP
177 LABEL BGI OVAL FM
185 RETAINING RING EXTERNAL
191 WASHER 5/16” FC
Part No 520187
Form No F010408A
25
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
ACCESSORIES
GRASS CATCHER KIT P/N 520142
Purpose: Easily convert your mower to bag grass and leaves.
1
4
1
0
3
1
0
2
5
9
1
1
7
8
6
I T E M
P
a r t N O
.
D E S
C
R I P
C A T C H E R
IR E F R A R A
R A C A T C H E R
T
I O
N
Q
T
Y
N O
1
.
G
W
G
B
B
S
R A
S
S
B
S
M
A
S
O
G
5 2 0 0 1 2
5 2 0 0 3 8
5 2 0 0 6 9
5 2 0 0 5 9
5 2 0 0 6 0
8 0 4 1 0 0 6
8 1 7 1 0 0 2
8 1 6 0 0 0 1
5 2 0 1 2 6
5 2 0 1 2 8
5 2 0 1 2 9
5 2 0 1 4 7
1
1
1
1
1
1
1
1
4
4
4
1
2
3
4
5
6
7
8
9
M
E
G
C A T C H E R F M
U N T
S
S
W
A
F M
R A C K E T
R A C K E T
C R E W C A
G
G
P
R A
R A
1 / 4 "
S
S
S
S
-
C A T H C E R L A T C H
C A T H C E R L A T C H
2 0
P
L
R
F M
F M
X
1 ”
Z
P
W
A
S
H E R 1 / 4 ” F C
Z
N U T L O C K 1 / 4 "
-
2 0
W
S
A
S
H E R # 8
C R E W R O U N D H E A
3 2
C A T C H E R
S
A
E
1 0
1 1
1 2
D
# 8 - 3 2
IT F M
X
3 / 4 ” C L E A
R
Z
IN C
N U T L O C K # 8
L IT R A
-
G
S
S
K
TRANSAXLE GUARD KIT P/N 520155
MULCHING KIT P/N 520144
Purpose: To protect the transaxle from accidental
contact from concrete curbs or other hazards.
Purpose: Reduces lawn clippings to fine nutrient-rich
particles that filter down to the soil.
3
4
2
2
2
1
Part NO.
ITEM
NO.
1
2
3
Part NO.
ITEM
NO.
1
2
3
DESCRIPTION
QTY
DESCRIPTION
QTY
BRACKET GUARD TRANSAXLE FM
SCREWCAP 5/16-18X1”
WASHER 1/4 FC
520151
8041028
8171002
8160002
1
4
2
4
MULCHING PLATE WA FM
BLADE 11.88” MULCHING
NUTLOCK 3/8”-16 THIN HGT
WASHER 5/16 FC
520014
520002
8161042
8171003
520148
1
3
2
2
1
4
NUTLOCK 5/16 - 18
4
5
LIT MULCHING KIT FM
Part No 520187
Form No F010408A
26
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
MAINTENANCE RECORD
Date
Service Performed
Part No 520187
Form No F010408A
27
Download from Www.Somanuals.com. All Manuals Search And Download.
FM Owner’s Manual
Part No 520187
Form No F010408A
28
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Black Decker Lawn Mower CMM1000 User Manual
Bolens Lawn Mower 114 330 000 User Manual
Craftsman Lawn Mower 24737683 User Guide
Land Pride Lawn Mower FM20 User Guide
Snapper Lawn Mower 1033 User Manual
Snapper Lawn Mower Accessory 1694542 User Manual
Snapper Lawn Mower E331315BE User Manual
Snapper Lawn Mower LT125G33BB User Manual
Snapper Lawn Mower WM301021BE User Manual
Weed Eater Lawn Mower 403284 User Guide