AL KO Lawn Mower 426 036 User Manual

426 036

b c d e f

2007

www.al-ko.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Do not start the engine if anyone is standing in

front of the cutter bar – the cutter and wheel

drives must not be engaged.

Safety instructions

General comments

Use the mower on grassy areas only.

Read the operating instructions carefully.

Familiarise yourself with the correct operation of

the mower.

The cutter drive must be disengaged when the

mower is not on a mowable surface.

Keep the operating instructions for later use and

for subsequent owners.

The blade guard must be mounted on the cutter

bar if the mower is transported or lifted.

Follow the safety instructions and warnings on

the mower.

Keep hands and feet away from rotating parts.

Never lift or carry the mower if the engine is

running. Wait until the cutters have stopped

moving, then pull off the spark plug connector.

Users

Children and juveniles under the age of 16 as

well as anyone who has not read the operating

instructions must not operate the mower. Local

regulations may specify the minimum age.

The mower may only be used if the safety

clearance determined by the handlebar is

maintained.

Wear long, close-fitting trousers and sturdy, non-

slip footwear.

Ensure that you have a secure footing.

Always mow across a slope.

Never mow up or down a slope or on slopes with

an inclination greater than 10°.

Working area

Carefully check the whole area to be mown.

Remove all foreign objects, such as stones,

sticks, wires, bones, etc.

Keep the exhaust and engine free of leaves,

grass and spilt oil.

Do not use the mower if there are any persons

(caution: children) or animals (including wildlife)

in the working area.

Do not leave the mower unsupervised – pull off

the spark plug connector.

Operating times

Comply with any national regulations regarding

operating times for lawn mowers (noise

prevention).

Warning!

Petrol is highly flammable!

Store petrol in designated containers only.

See the operating manual for operating times.

Refill with petrol outdoors only. Do not smoke

while refilling!

Use the mower only in daylight or if the working

area is well illuminated.

Do not open the tank cap or refill with petrol while

the engine is running or if the machine is hot.

Operation

Always make a visual inspection of the mower

before using it. The mower must be in a safe

operating condition.

Use a funnel or filling tube to refill petrol to

prevent fuel being spilt onto the engine, the

housing or on the ground.

Damaged or worn parts must be replaced

immediately.

If petrol has been spilt, do not start the engine.

Clean the mower and do not restart the engine

until the petrol vapours have dispersed.

Use the mower only if it is in the technical

condition stipulated by the manufacturer.

The person using the mower is responsible for

any accidents involving other persons or their

property.

Do not disable the safety or protective devices on

the mower.

Download from Www.Somanuals.com. All Manuals Search And Download.

GB1

For reasons of safety, replace a damaged petrol Spare parts and accessories

tank and/or tank cap.

Use genuine spare parts and accessories only.

We reserve the right to make changes to the

design and construction without prior notice.

Risk of burns!

The exhaust as well as the areas around the

exhaust may be very hot.

Explanation of the symbols

on the mower

Replace damaged mufflers.

Before using the mower for the first

time, read the operating manual!

Do not change the governor settings of the

engine.

Never leave a combustion engine running in an

enclosed space – toxic hazard!

Keep other people out of

the danger area!

Safety instructions for the cutter bar

Before working on the mower

pull off the spark plug connector!

Some of the blades on the cutter bar are bare.

These can lead to serious injuries if they are not

handled with care.

Keep hands and feet away

from the blades!

Always mount the blade guard on the cutter bar

for the following:

• mounting the cutter bar onto the mower

• cleaning the mower

• during transport and storage of the mower

• during work on the cutter bar

Intended use

This mower is intended for use in private and

hobby gardens only.

Replace damaged blade guards.

It must be operated with genuine accessories

only (cutter bar, winter kit).

Maintenance and storage

Before performing any work on the mower:

Non-permitted users:

Persons who are not familiar with the operating

manual, as well as children, adolescents under

the age of 16 and persons under the influence

of alcohol, drugs or medication must not

operate the mower.

switch off the engine, wait until the cutters have

stopped moving and then pull off the spark plug

connector.

Always wear safety gloves during work on the

cutters.

If there is petrol in the tank, never store the

mower in buildings where petrol vapours can

come into contact with naked flames or sparks –

Risk of explosion!

The petrol tank must be emptied outdoors only.

Allow the engine to cool before storing the mower

in an enclosed space.

Do not spray the mower with water.

The mower must be repaired by an authorised

specialist company only.

Download from Www.Somanuals.com. All Manuals Search And Download.

GB2

Operating times:

Please comply with any municipal regulations

on the operation of lawn mowers !

Setting the cutting height

The cutting height is adjusted using the skids (2).

Standard cutter bar

Monday – Saturday:

Sunday and public

holidays:

steplessly adjustable cutting height up to approx. 6

7.00 – 12.00 a.m.

3.00 – 7.00 p.m.

not permitted

• Loosen nuts ꢀ.

• Move the skids ꢁ to the required height.

• Retighten the nuts.

Assembly

Assemble this mower in accordance with the

separately enclosed assembly manual.

Both skids must be set to the same height !

Environmental protection, disposal

ESM cutter bar

The packaging material is made of recyclable

materials. Dispose of the packaging materials in

accordance with regulations.

a) Mounting the skid holders as

skids

The cutter bar cuts close to the ground

• Mount the adjustable skid holders as shown

in the illustration.

(the curved side points downwards).

Switching on the mower

Do not switch on the mower before it has been

completely assembled.

b) Mounting adjustable skids

The number printed on the left before the

steplessly adjustable cutting height up to

approx. 6 cm

text (e.g.

) refers to the diagrams.

• Mount the adjustable skid holders as shown

in the illustration.

(the curved side points upwards).

Petrol engine:

Before switching on the machine for the first

time, full it up with oil and petrol!

• Mount the skids as shown in the illustration.

The operating manual supplied by the

engine manufacturer for the petrol engine

must be followed.

Setting the cutting height

• Loosen the nuts ꢀ (2 nuts per skid).

• Move the skids ꢁ to the required

Drive gears:

Gear oil has been filled at the works.

height.

• Retighten the nuts.

Setting the handlebar height

Both skids must be set to the

same height!

Set the height of the handlebar according to

the user's height.

The height is usually adjusted to hip level.

Starting the engine

The clutch levers for the wheel and cutter

drives must not be engaged when starting the

engine!

• Loosen the screws on the housing console.

• Set the height of the handlebars using the

longitudinal holes.

• Retighten the screws.

Set the throttle lever to the << START>>

position.

Depending on the model, the handlebar can

Press the primer button 3x with intervals of

additionally be adjusted using the upper or lower

height settings on the housing console.

approx. 2 seconds.

If the temperature is below 10° C, press the

primer button 5x.

If the engine is warm, do not press the primer

button!

Download from Www.Somanuals.com. All Manuals Search And Download.

GB3

Maintenance and servicing

Quickly pull out the starter cable and then

allow it to slowly rewind.

Before carrying out any maintenance or

cleaning work, pull off the spark plug

connector!

As soon as the engine is running, set the throttle

lever between the "start" and "stop" positions

according to the desired engine speed.

Do not spray the mower with water. Water that

enters the ignition system or the carburettor may

lead to malfunctions. Clean the mower with a

cloth, hand brush, etc.

To start mowing, move the lever to the <START>

position - (full throttle).

Switching on the cutter bar

When the mower is tilted sideways and

depending on the engine manufacturer

Unlock the safety catch ꢂ.

Fully depress the clutch lever ꢃ and hold it tight.

the

upwards!!!:

TECUMSEH:

BRIGGS & STRATTON:

following

part(s)

must

point

The cutters should begin to move only after

the lever has travelled half the distance. Readjust

the Bowden cable, if necessary –

⇐

the carburettor/air filter

the spark plug

⇐

(see under: Adjusting the Bowden cables).

See the operating manual from the engine

manufacturer!

Engaging the wheel drive

Cutter bar

Squeeze the clutch lever ꢀ to the handlebar

Clean the cutter bar after every use,

particularly the guidance and sliding surfaces.

This means dismounting the cutter.

Afterwards, oil all moving parts.

and hold tight.

The wheel drive should engage only after

the lever has travelled half the distance. Readjust

the Bowden cables, if necessary (see under:

Adjusting the Bowden cables).

Use only biodegradable lubricants!

Dismounting the cutter from the

cutter bar

a) Standard - cutter bar

Model with forward and reverse gears

15 • Remove screws ꢀ –

spring washer and

washer under the screw head!

Clutch lever ꢀ = forward wheel drive

Clutch lever ꢁ = reverse wheel drive

ꢄ



• Pull out part ꢁ forwards.

Do not operate both clutch levers atthe

same time!

When remounting part ꢁ – observe mounting

direction – protruding lug must point forwards!

Only engage: forward wheel drive or

• Loosening the cutter guides

16 • Loosen hexagonal nut and unscrew the

grub screw a little.

or reverse wheel drive at a time.

Disengaging the wheel drive

• Pull the cutter out sideways.

Remount in the reverse order.

Release clutch lever ꢀ or ꢁ.

If the lateral play between part ꢁ and

part ꢂ (natural wear) is greater than 1mm,

both parts must be replaced!

Switching off the cutter bar

Release clutch lever ꢃ.

Setting the cutting play

Switching off the engine

16 • Screw in the grub screw by hand until you

feel a resistance – then give it another ½

turn.

Move the throttle lever to the << STOP >>

position.

• Secure the grub screws with lock nuts.

• After setting, the cutters must still be freely

movable by hand.

Download from Www.Somanuals.com. All Manuals Search And Download.

GB4

• Carry out a test mow – if the cutting power

is insufficient, screw in the grub screw a

little.

Engine:

Changing the oil / air filter / spark plug

See the operating manual supplied by

the engine manufacturer.

b) ESM cutter bar

15 • Remove screws ꢀ – spring washer and

washer under the screw head!

Adjustment of the Bowden cables

19 a) Cutter bar (without a lock nut)

20 b) Wheel drive

• Pull out part ꢁ forwards.

When remounting part ꢁ observe

mounting direction – protruding lug must

point forwards!

• loosen the lock nut

For further information on dismounting the

cutter as well as maintenance of the cutter

bar ⇒ see: the separate sheet: ESM –

Cutter Bar Universal SC

• use the adjusting screw ꢁ to readjust

Correct setting:

The cutters and the wheel drive should only start

to move after the lever has travelled half the

distance.

If the play between part ( and part (

(natural wear) is greater than 1mm,

both parts must be replaced!

• Retighten the lock nuts.

* * * * * *

17 • Lubricate the cutter drive after every

8 operating hours using a commercial multi-

purpose grease – 2 grease nipples

Resharpening and exchanging the

cutter blades

Resharpen blunt blades with a suitable abrasive

stone keeping the same cutting angle

(approx. 35 – 40°). Dismount the cutters for

this.

Worn or damaged blades must be

replaced ⇒ customer service centre.

Expert inspection is required

for the following:

• if the mower strikes an object

• if the engine stops suddenly

• if the cutter bar is bent

• if the gears are damaged

• if the V belt is defective

Drive gears

18 Check the oil level in the gearbox regularly

• Make sure the mower is horizontal.

• Unscrew the oil plug.

• Oil level: up to lower edge of filling opening

Top up with gear oil, if necessary.

• Oil grade: gear oil SAE 80

• Oil capacity for mowers with:

forward gear only:

approx. 0.25 l

forward and reverse gear: approx. 0.50 l

Download from Www.Somanuals.com. All Manuals Search And Download.

GB5

Warranty

We will rectify any material or production faults

on the mower during the statutory period of

limitation for claims based on defects in

accordance with our choice of repair or

replacement.

The period of limitation is determined by the laws

of the country in which the mower was

purchased.

The following items are excluded from the

warranty:

• Paint damage due to normal wear.

• Natural wear and parts that are identified with

a frame XXX XXX (X) on the spare parts card.

• Combustion engines – separate warranty

conditions of the respective enginemanufacturer

apply.

Our warranty is only valid under the following

conditions:

In the event of a claim covered by the

warranty, please contact your dealer or the

nearest authorised customer service centre and

present this warranty declaration and the sales

receipt.

• The machine has been treated properly.

• The operating manual has been followed.

• Genuine spare parts have been used.

The warranty is void if:

• Attempts have been made to repair the

machine.

• The machine has been modified.

• The machine has not been used as intended.

• Commercial or municipal use, etc.

The statutory claims of the purchaser based on

defects with respect to the seller shall remain

unaffected by this guarantee undertaking.

Troubleshooting

Before carrying out any maintenance or cleaning work, pull off the spark plug connector!

Fault

Remedial action

Engine does not start

If the engine is cold: press the primer

Full up with petrol

Move the throttle lever to the start position

Push the spark plug connector onto the spark plug

Check the spark plug. Replace, if necessary

Clean the air filter

Engine power reduced

Inexact cut

Resharpen / replace the blades → customer service centre

Clean the air filter

Resharpen / replace the blades → customer service centre

Readjust the cutting play

Cutter drive / wheel drive

not functioning

Readjust Bowden cable

V - belt defect → customer service centre

Faults that cannot be rectified with the aid of this table must be eliminated by

an authorised workshop only (customer service centre).

Download from Www.Somanuals.com. All Manuals Search And Download.

GB6

Ausgediente Geräte nicht über den

Hausmüll entsorgen!

PĜístroje, které již dosloužily, nelikvidujte v

domácím odpadu!

Verpackung, Gerät und Zubehör sind aus

recyclingfähigen Materialien hergestellt und

entsprechend zu entsorgen.

Balení, pĜístroj a pĜíslušenství jsou z

recyklovatelných materiálĤ a musí se likvidovat

pĜedepsaným zpĤsobem.

Do not dispose of worn-out units through

the household garbage!

The appliance, its packaging and accessories

are all produced from recyclable materials and

must be disposed of accordingly.

Opotrebované prístroje nelikvidujte cez

domový odpad!

Obal, prístroj a príslušenstvo sú vyrobené z

recyklovateĐných materiálov a je potrebné ich

zodpovedajúco likvidovaĢ.

Les appareils usagés ne doivent pas être

mis au rebut avec les déchets ménagers!

Ɉɬɫɥɭɠɢɜɲɢɟ ɫɪɨɤ ɩɪɢɛɨɪɵ ɧɟ

ɜɵɛɪɚɫɵɜɚɬɶ ɫ ɛɵɬɨɜɵɦ ɦɭɫɨɪɨɦ!

RUS

Les emballages, l’appareil et ses accessoires

sont fabriqués en matériaux recyclables et

sont à éliminer selon l’usage dans votre pays.

ɍɩɚɤɨɜɤɚ, ɩɪɢɛɨɪ ɢ ɩɪɢɧɚɞɥɟɠɧɨɫɬɢ

ɢɡɝɨɬɨɜɥɟɧɵ ɢɡ ɦɚɬɟɪɢɚɥɨɜ, ɩɪɢɝɨɞɧɵɯ ɞɥɹ

ɜɬɨɪɢɱɧɨɝɨ ɢɫɩɨɥɶɡɨɜɚɧɢɹ, ɢ ɩɨɷɬɨɦɭ

ɞɨɥɠɧɵ ɭɬɢɥɢɡɢɪɨɜɚɬɶɫɹ ɫɨɨɬɜɟɬɫɬɜɭɸɳɢɦ

ɨɛɪɚɡɨɦ.

Non smaltire gli apparecchi usati con i

rifiuti domestici!

L’imballo, la macchina e gli accessori sono

prodotti con un materiale che può essere

riciclato e di conseguenza vanno smaltiti in

modo appropriato.

ȂȘȞ ʌİĲȐĲİ ĲȚȢ ȝİĲĮȤİȚȡȚıȝȑȞİȢ ıȣıțİȣȑȢ

ıĲĮ ȠȚțȚĮțȐ ĮʌȠȡȡȓȝȝĮĲĮ!

Ǿ ıȣıțİȣĮıȓĮ, Ș ıȣıțİȣȒ țĮȚ ĲĮ İȟĮȡĲȒȝĮĲĮ

ȑȤȠȣȞ țĮĲĮıțİȣĮıĲİȓ Įʌȩ ĮȞĮțȣțȜȫıȚȝĮ ȣȜȚțȐ țĮȚ

ĮʌȠıȪȡȠȞĲĮȚ ĮȞȐȜȠȖĮ.

Geef het gebruikte apparaat niet met het

huisvuil mee!

Hizmetini doldurmuú aletleri ev çöpüyle yok

etmeyiniz!

De verpakking, het apparaat en de

accessoires zijn van materiaal gemaakt dat

hergebruikt kan worden. Lever uw bijdrage

hiervoor.

Ambalaj, Alet ve Teçhizatlar yeniden

de÷erlendirilebilir malzemelerden yapılmıútır ve

buna uygun olarak yok edilmelidir

¡No elimine las máquinas fuera de uso con

los residuos domésticos!

Los embalajes, la máquina y los accesorios

están fabricados con materiales reciclables y

deben desecharse adecuadamente.

Udtjente maskiner må ikke bortskaffes

sammen med normalt husholdningsaffand!

Emballagen, maskinen og tilbehøret er

fremstilles af genbrugelige materialer og skal

bortskaffes tilsvarende.

A eliminação de aparelhos usados não

deve ser feita através da recolha de lixo

normal!

A embalagem, o aparelho e seus acessórios

são fabricados com materiais recicláveis,

devendo ser adequadamente eliminados como

lixo reciclável.

Släng inte uttjänta maskiner med

hushållssoporna!

Förpackning, maskin och tillbehör är tillverkade

av återvinningsbara materialier och måste

omhändertas i enlighet därmed.

A kiselejtezett gépet ne dobja a háztartási

szemétbe!

Ikke kast utgåtte maskinen sammen med

husholdningsavfallet!

A csomagolás, a gép és a tartozékok anyagai

újrahasznosíthatók. Hulladékként történĘ

kezelésüket ennek megfelelĘen kell végezni.

Emballasje, maskinen og tilleggsutstyr er

tilvirket ved hjelp av gjenbruksmateriale, og

skal avfallsorteres som gjenbruksmateriale.

Nie usuwaü zuĪytych urządzeĔ z odpadami

domowymi !

Älä hävitä käytöstä poistettuja laitteita

talousjätteen mukana!

FIN

Opakowanie, urządzenie i wyposaĪenie

wykonano z materiaáów nadających siĊ do

recyklingu, naleĪy je zutylizowaü w odpowiedni

sposób.

Pakkaus, laite ja lisätarvikkeet on valmistettu

kierrätyskelpoisista materiaaleista, ja ne on

hävitettävä asianmukaisella tavalla.

Download from Www.Somanuals.com. All Manuals Search And Download.

Land

Firma

Tel

Fax

AL-KO Kober Ges.m.b.H.

AL-KO International PTY. LTD

Eurogarden NV

(+43) 3578/2515227

(+61) 3/9767-3700

(+32) 16/805427

(+41) 56/4183150

(+420) 382/210381

(+49) 8221/203-0

(+45) 98 82 10 00

(+34) 93/3002618

(+33) 3/85-763540

(+44) 1963/828050

(+36) 29/537050

(+385) 1 3096 567

(+39) 039/9 329311

(+352) 507622

(+43) 3578/251538

(+61) 3/9767-3799

(+32) 16/805425

(+41) 56/4183160

(+420) 382/212782

(+49) 8221/203-138

(+45) 98 82 54 54

(+34) 93/3001769

(+33) 3/85-763588

(+44) 1963/828052

(+36) 29/537051

(+385) 1 3096 567

(+39) 039/9329390

(+352) 504889

AUS

AL-KO Kober AG

AL-KO Kober Spol.sr.o.

AL-KO Geräte GmbH

AL-KO Ginge A/S

ANMI

AL-KO S.A.S.

Rochford Garden Machinery Ltd.

AL-KO KFT

Brun.ko.-prom d.o.o.

AL-KO Kober GmbH / SRL

Bobinage Back

AL-KO Kober SIA

(+371) 7/409330

(+47) 64 86 25 50

(+31) 18/2567824

(+48) 61/8161925

(+4) 021 326 36 72

(+7) 095/1688716

(+7) 812/4461084

(+46) (0)31 573 580

(+421) 2/45994112

(+386) 4 2046884

(+90) 232 4580586

(+380) 44/4923396

(+371) 7807018

(+47) 64 86 25 54

(+31) 18/2533895

(+48) 61/8161980

(+4) 021 326 36 79

(+7) 095/1623238

(+7) 812/4461084

(+46) (0)31 575 620

(+421) 2/45648117

(+386) 4 2049730

(+90) 232 4572697

(+380) 44/4923397

Stand 06/2007

AL-KO GINGE A/S

Mechatechniek B.V.

AL-KO Kober z.o.o.

OMNITECH TRADING SA

OOO AL-KO Kober

AL-KO St. Petersburg GmbH

AL-KO Ginge Svenska AB

AL-KO Kober Slovakia Spol.s.r.o.

SERVIS HUDOBIVNIK

ZIMAS A.S.

RUS

SLO

TOV AL-KO Kober

AL-KO Geraete GmbH

Head Quarter

Ichenhauser Str. 14

89359 Koetz

Deutschland

Telefon: (+49)8221/203-0

Telefax: (+49)8221/203-138

www.al-ko.com

451 313

Download from Www.Somanuals.com. All Manuals Search And Download.

Assembly

BM 5001-R (B&S)

Assembly of the double wheels

Fill the mower with engine oil and

petrol only after it has been

completely assembled!

Pull off the spark plug connector

before starting the assembly!

Carry out the following steps on both

drive wheels.

13. Remove screw

hexagonal screw M8 x 45

hexagonal nut

M8 self-locking

The number printed on the left before

14. y Mount axle extender

the text (e.g. ) refers to the diagrams.

y Re-insert screw and retighten nut.

.1. .2. Loosen screws and rotate handlebar

15. Push the wheel onto the axle extender

console upwards – retighten screws.

16. Check the orientation of the wheel – the

tyre profiles should form a V viewed in the

direction of travel.

Assembly of handlebars on console

.3. Handlebars

17. Secure wheel with nut

Washer

Hexagonal nut

Ø 10 x Ø 35 x 5

M10 self-locking

.4. Mount handlebars on console.

Hexagonal screw M8 x 25 - (2x)

Hexagonal nut

Bowden cable guide - (1x)

M8 self-locking - (2x)

18. Press on protective cap

.5. The handlebars can be set to the user's

height by attaching them to the lower or

upper position.

Assembly of Bowden cables

a) Bowden cable for throttle

.6. Mount the Bowden cable guide together

y Set the throttle lever on the right-hand

handlebar to the << START>> position.

with the lower screw - tighten the nuts.

19. Push the governor lever on the carburettor

Assembly of blade holder

completely to the left (= start position).

.7. Blade holder

20. y Insert the angled end of the Bowden

cable wire into the governor lever.

.8. Mounting bush on the housing to

accommodate the blade holder.

y Insert the Bowden cable sheath in the clip

y Gently push back the Bowden cable

sheath by hand until a resistance can be

felt.

Clamp the Bowden cable sheath in this

position.

.9. Lightly grease the mounting bush and insert

the blade holder.

10. Fully insert the blade holder and place the

V belt around the pulley.

Place the V belt around the lower pulley

in the housing.

Do not kink the Bowden cable during

assembly.

Assembly of recoil springs

11. 12. y Place the mower on its side.

y Hook in the recoil springs (2x).

GB 1

Download from Www.Somanuals.com. All Manuals Search And Download.

b) Bowden cables for the wheel drive

c) Bowden cable for cutter bar

This mower has a forward drive and a

reverse drive.

The Bowden cable for the cutter bar is on the

left side of the housing viewed in the direction

of travel.

1.) Bowden cable for reverse drive

28 Screw back both nuts on the upper Bowden

21 The Bowden cable for the reverse drive

comes out of the housing below the engine

on the right (viewed in the direction of

travel) and is additionally labelled R..

cable adjuster all the way.

29 Thread the Bowden cable through the

console.

30 Thread the Bowden cable through guide on

22 Insert the bent hook of the .R. Bowden

cable into the lower hole on the inward side

of the right-hand handlebar lever.

the console.

31 Thread the bent hook through the hole in

the holder and push the adjuster up to the

holder.

23 y Unscrew the foremost nut on the adjuster "a".

y Insert the adjuster in the holder and

retighten the nut.

There is no insertion slit on the holder!

32 y Insert the bent hook through the red

24 Lay the Bowden cable along the inner side

handlebar lever.

of the handlebar console.

y Set the lower adjuster on the housing to

its middle position.

Correct adjustment of the Bowden cable:

see under: "Adjustment of Bowden

cables" in the operating manual of the

mower.

Correct adjustment of the Bowden cable:

See under: "Adjustment of Bowden

cables" in the operating manual of the

mower.

2.) Bowden cable for forward drive

33 Bind the Bowden cables together with a

25 The Bowden cable for the forward drive is

on the right side of the housing viewed in

the direction of travel.

cable tie on the inner side of the console.

Protective cover

26. y Insert the bent hook of the Bowden cable

into the lower hole on the outward side of

the left-hand handlebar lever.

34 Remove the nuts and washers on the blade

holder.

35 Mount the protective cover and tighten the

y Insert the Bowden cable sleeve "a" into

the holder on the handlebars.

nuts.

Do not completely tighten the upper nut

(width across flats 19 mm).

27 Adjust the lower end of Bowden cable on

the housing to the correct setting.

See under: "Adjustment of Bowden cables"

in the operating manual of the mower.

36 Mount the protective cap on the rear of the

housing and secure with

hexagonal

drilling screw

4.8

16 (1x) and

washer Ø 5 (1x).

GB 2

Download from Www.Somanuals.com. All Manuals Search And Download.

Cutter bar

42 43 Screw the cutter bar and blade holder

together.

The cutter bar is not included in the

scope of delivery!

Hexagonal screw M8 x 25 (4x)

The mounting plate must be inserted

between the cutter bar and the blade

holder!

Carry out the following steps to mount the

ESM cutter bar.

Please observe the safety information and

maintenance instructions from the manufacturer

of the cutter bar.

44 There must be a gap of approx. 1 mm

between the start of the thread of the

headless screw "a" and the drive dog "b".

Adjust the headless screw correspondingly.

Mount the blade guard on the cutter

bar and wear safety gloves!

37 Assembly parts (supplied with the scythe

mower):

y Assembly of the skids on the cutter bar

See the Operating Manual.

1x Guide (plastic)

1x Drive dog

2x Allen screw M8 x 14

2x Washer Ø 8

* * * * * * * * * *

2x Spring washer Ø 8

1x Mounting plate

4x Hexagonal screw M8 x 25

38 Screw the guide centrally onto the cutter

bar.

Allen screw

Spring washer Ø 8 - (2x)

Washer Ø 8 - (2x)

M8 x 14 - (2x)

Pay attention to its orientation – the

protruding lug must point towards the

cutting blades.

The spring washer must lie underneath

the screw head!

39 Place the mounting plate on the cutter bar.

40 Align the cutter bar on the blade holder in

the attachment position - align the drive dog

on the centre of the blade holder (turn the

V-belt pulley for this).

Lightly grease the drive dog before

mounting.

41 y Lift the scythe mower by the blade holder

so that the drive dog can be inserted into

the guide.

y Lower the mower again and insert the

headless screw into the drive dog.

GB 3

Download from Www.Somanuals.com. All Manuals Search And Download.

BM 5001 R (B&S) Art.Nr. 112 431

ca.140cm x 95cm x (101cm/112cm)

ca. 69 kg

91cm / 102cm

3,7 kW 3600 ^-1

4.00 - 6

ca. 2,25 km/h

L_WA102 dB(A)

a_vhw5,4m/s²

Download from Www.Somanuals.com. All Manuals Search And Download.

D- EG-Konformitätserklärung

F- Déclaration de conformité CE

NL- EC-verklaring van conformiteit

H- EU egybehangzósági nyilatkozat

CZ- Prohlášení o shodě s EU

N- EF-Konformitetserklæring

DK- EF-Overensstemmelseserklæring

RUS- Заявление о соответствии

нормам ЕС

GB- EC Declaration of Conformity

I- Dichiarazione di conformità CE

E- Declaración de conformidad de la CE

PL- Oświadczenie zgodności EWG

SK- Prehlásenie ES o konformite

S- EG-konformitetsförklaring

FIN- EU-yhdenmukaisuusilmoitus

SLO- Izjava o konformnosti s priporoèili EU

Wir / We / Nous / Noi / Wij / Nosotros / Mi / My / Prohlašujeme / Vi / Me / Мы:

ALKO Geräte GmbH Ichenhauserstraße 14 D 89 359 Kötz

Германия

erklären, dass die Maschine / declare that the machine / déclarons que la machine / dichiariamo che la macchina /

verklaren dat de machine / declaramos que la máquina / kijelentjük, hogy az alábbi gép /

oświadczymy, że maszyna ta w postaci / že stroj / prehlasujeme, že stroj / erkl rer, at maskinen /

förklarar, att denna maskin / ilmoitamme, että kone / заявляем, что данный продукт /

izjavljamo, da stroji:

Balkenmäher

Cutter bar mower

Balkmaaier

Slåmaskin

Faucheuse à barre de coupe

Motosegadora

Motofalciatrice

Homlokfűnyiró

Græsslåmaskine

Slåttermaskin

Nittokone

Typ / Type / Tipo / del tipo / típus / typu / Tyyppi / Тип / Tip:

BM 870 II

BM 875 II

BM 5001 R

chnittbreite / Cuttingwidth / Largeur de coup/Larghezza di taglio / Maaibreedte / Ancho de corte / Klippebredde / Snittbredd / Leikkausleveys /

Vágási szélesség / šířka řezu / Szerokość cięcia / Ширина среза /

Širina reza:

87 cm

91/102 cm

mit folgenden EG-Richtlinien übereinstimmt / conforms to the specifications of the following EC directives /

st conforme aux spécifications des directives CE suivantes / è conforma alle seguenti direttive CE / overeenstemt met de volgende

CE-richtlijnen / Cumple las siguientes directrices de la CE / megfelel a következő EK-direktíváknak / odpowiada

następującym watacznym EWG / odpovídá následujícím směrnicím EU / zodpovedá nasledujúcim smerniciam ES / er i samsvar

med følgende EF-direktiver / stämmer överens med följande EG-direktiv / stemmer over ens med følgende EF-direktiver /

vastaa seuraavia EU-direktiivejä / соответствует следующим требованиям ЕС-директивы / ustrezjo naslednjim priporočilom EU:

98/37/ EG, 89/336/EWG,

egebenenfalls angewendete Normen / Where appropriate applied standards / Le cas échéant, standards appliqués/ norme eventualmente

applicate/ toegepaste normen, indien van toepassing / normas eventualmente aplicadas / Применены соответствующие нормативы /

upoštevani standardi, če je to potrebno:

EN 12733, EN ISO 14982

Kötz

19.12.2005

De Filippo

Geschäftsleitung

Ort / Place / Lieu /

Località / Plaats /

Localidad /

Datum / Date / Data /

Dátum / Dato /

Дата:

Unterschrift / Signature / Firma

Handtekening / Aláírás / Podpis

Underskrift / Signatur / Aika

Подпись / Podpis:

Beauftragter / Representative / Délégué /

Responsabile / Gemachtigd / Delegado /

Meghatalmazott / Zleceniobiorca /

Představitel / Zodpovedný / Representant /

Representat / Autoriseret repræsentant /

Valtuutettu / Уполномоченный /

Pooblaščenec:

Helyiség /

Miejscowość /

Miesto / Sted / By /

Paikka / Место / Kraj:

Download from Www.Somanuals.com. All Manuals Search And Download.

Land

Firma

Tel

Fax

AL-KO Kober Ges.m.b.H.

(+43) 3578/2515227

(+43) 3578/251538

AUS

AL-KO International PTY. LTD

Eurogarden NV

(+61) 3/9767-3700

(+32) 16/805427

(+41) 56/4183150

(+420) 382/210381

(+49) 8221/203-0

(+45) 98/82-1000

(+34) 93/3002618

(+33) 3/85-763540

(+44) 1963/828050

(+36) 29/537050

(+39) 039/9 329311

(+371) 7/409330

(+47) 64/862550

(+31) 18/2567824

(+48) 61/8161925

(+7) 095/1688716

(+7) 812/4461084

(+46) 31/573580

(+421) 2/45994112

(+386) 42588290

(+380) 44/4923396

(+61) 3/9767-3799

(+32) 16/805425

(+41) 56/4183160

(+420) 382/212782

(+49) 8221/203-138

(+45) 98/82-5454

(+34) 93/3001769

(+33) 3/85-763588

(+44) 1963/828052

(+36) 29/537051

(+39) 039/9329390

(+371) 7807018

AL-KO Kober AG

AL-KO Kober Spol.sr.o.

AL-KO Geräte GmbH

AL-KO Ginge A/S

ANMI

AL-KO S.A.S.

Rochford Garden Machinery Ltd.

AL-KO KFT

AL-KO Kober GmbH / SRL

AL-KO Kober SIA

AL-KO GINGE A/S

(+47) 64/862554

(+31) 18/2533895

(+48) 61/8161980

(+7) 095/1623238

(+7) 812/4461084

(+46) 31/575620

(+421) 2/45648117

(+386) 42588805

(+380) 44/4923397

Stand 11/2005

RUS

Mechatechniek B.V.

AL-KO Kober z.o.o.

OOO AL-KO Kober

AL-KO St. Petersburg GmbH

AL-KO Ginge Svenska AB

AL-KO Kober Slovakia Spol.s.r.o.

Merkur d.d.

SLO

TOV AL-KO Kober

AL-KO Geraete GmbH

Head Quarter

Ichenhauser Str. 14

89359 Koetz

Telefon: (+49)8221/203-0

Telefax: (+49)8221/203-138

www.al-ko.com

451 313

Download from Www.Somanuals.com. All Manuals Search And Download.

Bolens Lawn Mower 5264D User Manual
Gravely Lawn Mower 991079 User Guide
Husqvarna Lawn Mower 532 42 62 26 User Guide
McCulloch Lawn Mower 96041000901 User Guide
Poulan Lawn Mower 177545 User Guide
Ryobi Lawn Mower M48 Pro User Guide
Snapper Lawn Mower 1691816 User Manual
Snapper Lawn Mower AP21507B User Manual
Snapper Lawn Mower NP216012 User Manual
Snapper Lawn Sweeper 151 3845 User Guide