Central Hydraulics Automobile Accessories 3 ton floor hack User Manual

3 TON FLOOR JACK  
Model 34271  
ASSEMBLY and OPERATING INSTRUCTIONS  
Diagrams within this manual may not be drawn proportionally.  
Due to continuing improvements, actual product may differ slightly from the product described herein.  
Distributed exclusively by Harbor Freight Tools®.  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Read this material before using this product.  
Failure to do so can result in serious injury.  
SaVe THiS manual.  
Copyright© 1997 by Harbor Freight Tools®. All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
For technical questions or replacement parts, please call 1-800-444-3353.  
REVISED 08/05  
11. MAINTAIN TOOLS WITH CARE. Keep tools clean for better and safer performance. Fol-  
low instructions for lubricating the Jack. The handles must be kept clean, dry and free from oil and  
grease at all times.  
12. STAY ALERT. Watch what you are doing, use common sense. Do not operate any tool when you  
are tired.  
13. CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged should be  
carefully checked to determine that it will operate properly and perform its intended function. Check  
for alignment and binding of moving parts, any broken parts or mounting fixtures; and any other  
condition that may affect proper operation. Any part that is damaged should be properly repaired or  
replaced by a qualified technician.  
14. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replace-  
ment parts. Use of any other parts will void the warranty. Only use accessories intended for use with  
this tool. Approved accessories are available from Harbor Freight Tools.  
15. DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read  
warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking  
drugs. If there is any doubt, do not operate the tool.  
16. MAKE SURE ALL EQUIPMENT IS RATED TO THE APPROPRIATE CAPACITY. Never  
exceed the 6000 lbs. maximum lift capacity.  
UNPACKING  
Remove your 3 TON FLOOR JACK from the packaging materials.  
CAUTION  
The Floor Jack is HEAVY.  
Use caution when lifting  
When unpacking, check to make sure the following parts  
are included. All sizes listed below are approximate. If any  
parts are missing or broken, please call Harbor Freight Tools  
at the number on the cover of this manual.  
out of box.  
Item #  
N/A  
36  
Description  
Jack  
Lower Handle  
Upper Handle  
37  
GENERAL  
Always use good quality hydraulic jack oil when adding or replacing the oil in your Floor Jack. Do  
not mix different types of oils together. When filling the Floor Jack with oil, do not permit dirt or any  
other substance to enter the hydraulic system.  
REV 03/04  
Page# 3 — SKU: 34271  
ASSEMBLY  
You will need a 3/8” and an 11/16” wrench to complete assembly.  
Step 1. Take LOWER HANDLE (#36) and remove the HEX HEAD SCREW (#38).  
Step 2: Insert the fitted end of the UPPER HANDLE (#37) into LOWER HANDLE. Rotate  
HANDLES until the bolt holes line up in the center of the Handle Assembly.  
Step 3: Insert HEX HEAD SCREW and tighten with a 10mm wrench as shown in Figure 1.  
(#37)  
(#38)  
(#36)  
Step 4: Remove HANDLE BOLT (#34) from the HANDLE SOCKET (#39).  
Step 5: Insert Handle Assembly into HANDLE SOCKET and turn Handle Assembly clockwise  
until it engages the pressure release gear located underneath the HANDLE SOCKET.  
Step 6: Thread HANDLE BOLT into HANDLE SOCKET and securely hand tighten the bolt as  
shown in Figure 2.  
(#34)  
(#39)  
Your Floor Jack is ready for use.  
REV 08a  
Page# 4 — SKU: 34271  
OPERATION  
Step 1: Twist the Handle Assembly clockwise to close  
the pressure release valve as shown in Figure 3.  
WARNING  
Make sure you do not overload  
your Floor Jack. Rated capacity  
is 6000 pounds.  
WARNING  
Chalk vehicle’s wheels to  
prevent rolling while lifting.  
Step 2: Maneuver the Floor Jack underneath the vehicle. Check the vehicle’s Owners Manual for  
proper jacking points. Do not lift vehicle by the body.  
Step 3: Begin jacking by lowering the Handle Assembly as shown in Figure 4.  
(#12)  
Step 4: Lift Handle Assembly as high as clearance allows.  
Step 5: Repeat Steps 3-4 until vehicle is at desired height. Do not over-extend the jack.  
REV 03/04  
Page# 5 — SKU: 34271  
CAUTION  
Use jack stands to support vehicle.  
Never work around or under a vehicle  
supported only by the Floor Jack.  
Step 6: Place jack stands underneath vehicle at specified points. Refer to the vehicle’s Owners  
Manual for proper jack stand placement locations.  
Step 7: Slowly twist Handle Assembly counterclockwise. This will lower the vehicle onto the  
jack stands.  
WARNING:  
Watch for movement of vehicle or jack stands as vehicle is lowered.  
If any movement occurs, jack vehicle up and adjust jack stands properly.  
Step 8: Completely lower the Floor Jack and remove from underneath the vehicle.  
CAUTION:  
When not in use, make sure pressure is released  
by turning Handle Assembly fully counterclockwise.  
This will prolong the life of the jack.  
Step 9: To make sure vehicle is stable, stand away and attempt to rock the vehicle. If movement  
is detected, jack up the vehicle and adjust jack stands properly. Test again.  
MAINTENANCE  
Bleeding the Floor Jack  
Step 1. Place Floor Jack on a clear section of floor.  
WARNING  
Make sure you release  
jack pressure (Step 2)  
Step 2: Open the pressure release valve by turning the Handle  
Assembly fully counterclockwise.  
before proceeding.  
Step 3: Open the Air Vent Plug located on top of the LIFT ARM  
ASSEMBLY (#10) at the rear of the Arm Assembly.  
Step 4: Hold the SADDLE down and pump the Handle Assembly rapidly several times as shown  
in Figure 5.  
Page# 6 — SKU: 34271  
(#12)  
Step 5: Close the pressure release valve by turning the Handle Assembly fully clockwise.  
Step 6: If you need to have your jack serviced, take it to a qualified mechanic. The Floor Jack can-  
not be user serviced. Lubricate the Handle Assembly, Handle Socket, Lift Arm, Wheels, and Lift  
Arm Linkage before first use and at least twice per month (more often during heavy use) as shown in  
Figure 6.  
Page # 7 -- SKU: 34271  
Parts Diagram  
40  
41  
Page # 8 -- SKU: 34271  

Brother USUARIO MFC J410W User Manual
Chief Manufacturing Pit Boss 638699 User Manual
Dakota Digital LAT NR162 User Manual
Danby DESIGNER DAC9003D User Manual
Friedrich WallMaster UE12A33B User Manual
Frigidaire FRA103KT1 Window Air Conditioner FRA103KT1 User Manual
GE Zoneline AZ29E09EAC User Manual
HoMedics Adjustable Height Lumbar Massager LLUV 200 User Manual
Honda Power Equipment G35 User Manual
HP Hewlett Packard PHOTOSMART WIRELESS B109 User Manual