NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
PLATINUM MARCY
HOME GYM
Hardware Identifier
Assembly Instruction
Parts List
PM-3200
Resistance Chart
Warranty
Ordering Parts
Model
PM-3200
Retain This
Manual for
Reference
110525
OWNER'S
MANUAL
IMPEX® INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Do not intend to insert weight selector pin while the weight stack or top plate
is in elevated position.
14. Be certain the weight Selector Pin is completely inserted.
15. Never use dumbbells or other means to increase the weight resistance. Use only weight
plates provided by manufacturer.
16. This machine is designed and intended for home and consumer use only, not for
commercial use
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL PLACEMENT
The warning labels shown here have been placed on the Rear Base Frame and Upper Frame. If the labels
are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the
labels in the location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required for Assembling the Machine: Two Adjustable Wrenches, two Allen
Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended this machine
to be assembled by two or more people to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Push two Ø 2 3/8” x 1” Rubber Bumpers (#43) onto the Guide Rods (#13) from the bottom.
Insert the Guide Rods into the holes on the Rear Base Frame (#2). The Guide Rods have
holes on the rods about 2/3 way down the rods: for locking the weight stack when not in
use. The shorter end of the Guide Rod with the lock holes need to be pointed
downwards towards the Rear Base Frame.
B.) Secure them with two M10 x 1” Allen Bolts (#73) and two Ø ¾” Washers (#84) from the bottom
of the Rear Base Frame.
C.)Do not tighten Nuts and Bolts starting from next step until instructed to do so.
D.)Attach the Front Vertical Frame (#3) to the Base Frame (#5). Secure it with two M10 x 3 ½”
Carriage Bolts (#78), one 5 ½” x 2” Bracket (#21), two Ø ¾” Washers (#84), and two M10
Aircraft Nuts (#83) from bottom.
E.) Connect the Base Frame to the Rear Base Frame (#2). Secure it with two M10 x 2 ¾”
Carriage Bolts (#80), one 4 3/8” x 3” Bracket (#29), two Ø ¾” Washers (#84), and two M10
Aircraft Nuts (#83).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Slide the 14 Weight Plates (#34) onto the Guide Rods (#13). Make sure the deep grooves
on the Plates are all facing down and toward back of the machine. If the locking holes
on the guide rods are more than 2-3 inches from the upper most, then you have
installed the Guide Rods upside down. Align the holes of the Weight Plates. Insert the
Selector Rod (#14) through the center hole. Slide the ring on the L-shaped Weight Selector
Pin (#65) onto the Selector Rod. Use the L-shaped Weight Selector Pin to select the number
of Plates to exercise. Please refer Weight Resistance Chart in page 24.
C.)Slide the Selector Stem (#33) onto the Guide Rods.
D.)Attach the Upper Frame (#4) to the two Guide Rods. Place the Upper Frame onto the Front
Vertical Frame (#3).
E.) Secure the Upper Frame to the Guide Rods with two M10 x 1” Allen Bolts (#73) and two Ø
¾” Washers (#84).
F.) Secure the Upper Frame to the Front Vertical Frame with two M10 x 3 ½” Carriage Bolts
(#78), one 5 ½” x 2” Bracket (#21), two Ø ¾” Washers (#84), and two M10 Aircraft Nuts
(#83).
G.)Securely tighten all Nuts and Bolts previously installed in Step-1 and Step-2.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Front Press Base (#6) to the Upper Frame (#4). Secure it with one 6 1/8” Front
Press Axle (#37), one Ø ¾” Washer (#84), one Ø ¾” Lock Washer (#88), one M10 x 1” Allen
Bolt (#73), and one Ø 2” End Cap (#47) on each end of the Axle.
B.) Insert the axle on the Right Butterfly Base (#7) into the Front Press Base from bottom. Slide
a Lock Ring (#52) onto the Axle. Align the holes. Secure it with one M6 x 1 ¾” Allen Bolt
(#77) and M6 Aircraft Nut (#89).
C.) Attach the Right Butterfly (#9) to the Front Press Adjustment Frame (#31) on the Right
Butterfly Base. Insert a M8 x ¾” Allen Bolt (#92) through Right Butterfly to the open track on
the Adjustment Frame (#31). Secure the Bolt with one Ø ½” Washer (#87) and one M6
Aircraft Nut (#89). Do not over tighten the Nut. Make sure the Bolt can travel along the
track freely.
D.) Rotate the Right Butterfly and thread a M18 Quick Release Lock Pin (#55) into the selected
hole on Front Press Adjustment Frame to obtain desired Front Press position.
E.) Slide a Butterfly Large Foam Roll (#63) onto the Right Butterfly arm. Attach a Front Press
Handle (#30) to the Right Butterfly. Secure it with a M10 x 1” Allen Bolt (#73) and Ø ¾”
Washer (#84).
F.) Repeat B to E above to install the Left Butterfly Base (#8) and Left Butterfly (#10).
G.) Attach a Swivel Pulley Brackets (#26) to an open pulley bracket on the back of Front Vertical
Frame (#3). Secure it with one M10 x 2 ½” Allen Bolt (#69), two Ø ¾” Washers (#84), and
one M10 Aircraft Nut (#83). Repeat the same step to install the other Swivel Pulley Bracket
on the other side.
H.) Attach the Backrest Board (#39) to the Backrest Board Support Frame (#24). Secure it with
two M8 x 1 5/8” Allen Bolts (#75) and two Ø 5/8” Washers (#86). Insert the Support Frame
into the open slot on Front Vertical Frame. Use a M18 Lock Knob (#54) lock the Support
Frame at selected position.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 3
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Main Seat Support (#1) to the Front Vertical Frame (#3). Secure it with two M10 x
3 ¾” Carriage Bolts (#79), one 4 ¾” x 1 ¾” Bracket (#22), two ¾” Washers (#84), and two
M10 Aircraft Nuts (#83).
B.) Attach the Seat Bracket (#20) onto the Main Seat Support. Place the Seat Pad (#38) onto
Main Seat Support and Seat Bracket. Secure it with two M8 x 3” Allen Bolts (#74), two M8 x
5/8” Allen Bolts (#76), and four Ø 5/8” Washers (#86).
C.)Attach the Leg Developer (#11) to the open bracket on the Main Seat Support. Secure it with
one M12 x 3 1/8” Allen Bolt (#81), two Ø 1” Washers (#85), and one M12 Aircraft Nut (#91).
D.)Insert the Foam Tube (#28) halfway through the holes on the Leg Developer. Push two Foam
Rolls (#64) onto the Foam Tube from both ends.
E.) Attach the Arm Curl Pad (#40) to the Arm Curl Stand (#12). Secure it with two M8 x 5/8”
Allen bolts (#76) and two Ø 5/8” Washers (#86). Insert the Arm Curl Stand into the front
opening on the Main Seat Support. Use a M18 Lock Knob (#54) to lock the Arm Curl Stand
in position.
DIAGRAM 4
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP DIAGRAM
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5 & Cable Loop Diagram)
A.) Attach the 118” Upper Cable (#59) to the opening on the front of the Upper
Frame (#4). Note: The Ball Stopper on the cable should be underneath the
Frame.
B.) Attach a Pulley (#62) to the opening. Secure it with one M10 x 2 ½” Allen Bolt
(#69), two Ø 7/8” x 5/8” Pulley Bushings (#44), and one M10 Aircraft Nut (#83).
C.) Draw the Cable over the Pulley towards the back of the machine to the second
opening on the Upper Frame. Repeat step B above to install a Pulley.
D.) Draw the Cable around the Pulley then pull back to the opening on the Front
Press Base (#6).
E.) Attach a Pulley to the opening on the Front Press Base. Secure the Pulley with
one M10 x 6 ¾” Allen Bolt (#97), two Ø ¾” Washers (#84), and one M10 Aircraft
Nut (#83).
F.) Draw the Cable around the Pulley and then to the opening on the Front Vertical
Frame (#3). Attach a Pulley to the opening. Secure it with one M10 x 2 3/8” Allen
Bolt (#70), two Ø 7/8” x ½” Pulley Bushings (#45), and one M10 Aircraft Nut
(#83).
G.) Draw the Cable around the Pulley then pull the Cable downwards. Attach the
Cable to two Double Floating Pulley Brackets (#23). Attach a Pulley and a L-
shaped Cable Retainer (#27) to the top holes on the Brackets. Secure them with
one M10 x 1 ¾” Allen Bolts (#71), two Ø ¾” Washers (#84), and one M10 Aircraft
Nut (#83). Let the Brackets hanging just for now.
H.) Pull the Cable upward to the opening on the rear of Upper Frame. Repeat B to
install a Pulley.
I.) Pull the Cable downward between the two Guide Rods to the Selector Rod (#14).
Thread the bolt at the end of the Cable into the opening on top of the Selector
Rod to secure the Cable.
J.) Connect a Chain (#66) to the Cable with a Hook (#67). Connect the Lat Bar to
the Chain with another Hook. Change the length of the Chain to the Cable to
obtain the desired Lat Bar exercises.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 5
16
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6 & Cable Loop Diagram)
A.) Attach one end of the 110” Butterfly Cable (#61) onto the hook on the Right Butterfly
Base (#7).
B.) Draw the Cable to the right Swivel Pulley Bracket (#26).
C.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#71), two Ø ¾”
Washers (#84), and one M10 Aircraft Nut (#83).
D.) Draw the Cable around the Pulley then downward. Attach the Cable to an Angled Floating
Pulley Bracket (#25). Repeat C to install another Pulley. Let the Bracket hang for now.
E.) Pull the Cable around the Pulley then upward to the left Swivel Pulley Bracket. Repeat
Step C above to install a Pulley.
F.) Draw the Cable to the Left Butterfly Base (#8). Repeat A to secure the end of the Cable to
the Left Butterfly Base.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 6
18
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach the 157” Lower Cable (#60) to the opening on the bottom of the Leg Developer
(#11).
B.) Attach a Pulley (#62) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#69),
two Ø 7/8” x Ø 5/8” Bushings (#44), and one M10 Aircraft Nut (#83).
C.) Draw the Cable underneath the Pulley to the open bracket on Base Frame (#5).
D.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#71), two Ø
¾” Washers (#84), and one M10 Aircraft Nut (#83).
E.) Draw the Cable underneath the Pulley to the opening on the bottom of Front Vertical
Frame (#3). Attach a Pulley to the opening. Secure it with on M10 x 2 3/8” Allen Bolt
(#70), two Ø 7/8” x ½” Pulley Bushings (#45), and one M10 Aircraft Nut (#83).
F.) Draw the Cable underneath the Pulley then pull the Cable upward to the Angled
Floating Pulley Bracket (#25) previously installed in Step-6. Repeat D to install a
Pulley.
G.) Draw the Cable around the Pulley then downward to the opening on the Base Frame
(#5). Repeat B to install another Pulley.
H.) Pull the Cable around the Pulley then upward to the Double Floating Pulley Bracket
(#23) previously installed in Step-5. Repeat D to install a Pulley with a L-shaped
Cable Retainer. Adjust the Cable tension by adjusting this Pulley position on the
Brackets. If the tension is too tight then move the Pulley down by one hole. If the
tension is too loose then move up one hole.
I.) Draw the Cable around the Pulley then pull downward. Attach end of the Cable to a
bracket on the Base Frame. Secure it with one M10 x 1” Allen Bolt (#73), two Ø ¾”
Washers (#84), and one M10 Aircraft Nut (#83).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 7
20
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 (See Diagram 8)
A.) Attach a Chain (#66) to the Lower Cable (#60) by using a Hook (#67). Attach the
Shiver Bar Handle (#19) to the Chain by using another Hook. Adjust the length of the
Chain to obtain the desired Arm Curl exercise. Replace Shiver Bar Handle with Ankle
Strap (#68) for various exercises. Remove the Chain and Shiver Bar Handle when
using the Leg Developer.
B.) Attach Right & Left Weight Stack Covers (#15 & #16) to the Upper Frame (#4), Base
Frame (#5), and Rear Base Frame (#2). Secure them with six M10 x 5/8” Allen Bolts
(#72) and ¾” Washers (#84).
C.)From the back of the Covers, secure the two covers together with three M5 x 3/8”
Philips Screws (#82) and three M5 Aircraft Nuts (#90).
D.)Insert a L-shaped Lock Pin (#93) through the hole on Guide Rod and lock with a
Combination Lock (#98) to prevent any un-authorized usage of the machine.
E.) Unlock the Lock and attach it to Selector Rod before using the machine.
DIAGRAM 8
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Set up the Lock Combination
A.) The combination is pre-set at 0-0-0 by the factory.
B.) Turn the dials to 0-0-0 and aligned to the Combination Set Up Line.
C.) Pull out the shackle and turn 1800.
D.) Press down on the shackle.
E.) Turn the dials (aligned to the Combination Set Up Line) to your desired combination.
F.) Pull out the shackle and twist back to normal position and the combination are set.
G.) Repeat Procedure C to F to re-set the combination.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
2” x 2 ¾” End Cap
Lock Ring
2” Sleeve
3
2
1
2
2
1
2
2
1
1
1
15
2
2
1
2
4
1
7
2
7
6
9
2
2
4
2
4
2
2
1
3
26
44
2
8
2
2
4
3
1
2
1
1
2
2
1
1
1
2
3
4
5
6
7
8
Main Seat Support
Rear Base Frame
Front Vertical Frame
Upper Frame
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
1
2
1
1
2
2
1
1
2
2
1
1
14
2
6
1
1
1
1
2
2
2
10
4
6
8
1
2
4
M18 Lock Knob
M18 Quick Release Lock Pin
Ø 1” Cone-shaped End Cap
Ø 1” End Cap
Base Frame
Front Press Base
Right Butterfly Base
Left Butterfly Base
Right Butterfly
Left Butterfly
Leg Developer
Arm Curl Stand
Guide Rod
Selector Rod
Right Weight Stack Cover
Left Weight Stack Cover
Lat Bar
Rotate Ring
Shiver Bar Handle
Seat Bracket
Plastic Ring
118” Upper Cable
157” Lower Cable
110” Butterfly Cable
Pulley
Butterfly Large Foam Roll
Foam Roll
L-shaped Weight Selector Pin
Chain
Hook
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Ankle Strap
M10 x 2 ½” Allen Bolt
M10 x 2 3/8” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 5/8” Allen Bolt
M10 x 1” Allen Bolt
M8 x 3” Allen Bolt
M8 x 1 5/8” Allen Bolt
M8 x 5/8” Allen Bolt
M6 1 ¼” Allen Bolt
M10 x 3 ½” Carriage Bolt
M10 x 3 ¾” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M12 x 3 1/8” Allen Bolt
M5 x 3/8” Philips Screw
M10 Aircraft Nut
Ø ¾” Washer
Ø 1” Washer
Ø 5/8” Washer
Ø ½” Washer
Ø ¾” Lock Washer
M6 Aircraft Nut
M5 Aircraft Nut
5 ½” x 2” Bracket
4 ¾” x 1 ¾” Bracket
Double Floating Pulley Bracket
Backrest Board Support Frame
Angled Floating Pulley Bracket
Swivel Pulley Bracket
L-shaped Cable Retainer
Foam Tube
4 3/8” x 3” Bracket
Front Press Handle
Front Press Adjustment Frame
Shiver Bar
Selector Stem
Weight Plate
Ø 1” x 3/8” Leg Developer Bushing
Ø 1” x Ø 5/8” Bushing
6 1/8” Front Press Axle
Seat Pad
Backrest Board
Arm Curl Pad
M12 Aircraft Nut
Shiver Bar Plastic Ring
2” Square End Cap
Ø 2 3/8” x 1” Rubber Bumper
Ø 7/8” x 5/8” Pulley Bushing
Ø 7/8” x ½” Pulley Bushing
Handle Grip
Ø 2” End Cap
Ø 1 ¾” x 1 5/8” Rubber Bumper
1” x 2” End Cap
M8 x ¾” Allen Bolt
L-shaped Lock Pin
M6 x 5/8” Philips Screw
Axle Cover
Ø 1 1/8” x 3 ¼” Bushing
M10 x 6 ¾” Allen Bolt
Combination Lock
2” x 2 ¾” Flat End Cap
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PM3200 WEIGHT RESISTANCE CHART
WEIGHT PLATE
Station
Front Press
Lat Pull
1
2
3
4
5
6
7
8
9
30
30
15
30
42
40
20
40
40
54
50
25
50
50
66
60
30
60
60
78
70
35
70
70
90 102 114 126
80
40
80
80
90 100 110
45 50 55
Butterfly
Low Pulley
90 100 110
90 100 110
Leg Developer 30
WEIGHT PLATE
13 14
Station
Front Press
Lat Pull
10 11
12
138 150 162 174 186
120 130 140 150 160
Butterfly
60
65
70
75
80
Low Pulley
120 130 140 150 160
Leg Developer 120 130 140 150 160
Note: Each plate weights 10 lbs.
Numbers are approximate. Actual weights may vary.
Values for Butterfly are for each arm.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX® INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing
or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or other damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures.
Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX® INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
25
Download from Www.Somanuals.com. All Manuals Search And Download.
|