NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
POWERHOUSE ELITE
PHE 2000
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
PHE 2000
Retain This
Manual for
Reference
05-31-04
OWNER'S
MANUAL
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions
apply whenever you operate a piece of exercise equipment. Be sure to read the
entire manual before you assemble or operate your machine. In particular, note the
following safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches
NOTE: It is strongly recommended this machine be assembled by two or more people
to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Place the Middle Base Frame (#1) between the Front & Rear Base Frames (#2 & #3).
Align the holes. Secure them with two M10 x 2 ¾” Carriage Bolts (#72), two ∅ ¾” Washers
(#87), and two M10 Aircraft Nuts (#89).
B.) Attach the Foot Plate (#15) to the Front Base Frame (#3). Align the holes. Insert the 15 ¾”
Foot Plate Axle (#33) through the holes. Secure the Axle with a M8 x ¾” Screw (#88).
C.) Attach the Vertical Frame (#5) to the Rear Base Frame (#2). Secure it with two M10 x 2 ¾”
Carriage Bolts (#72), ∅ ¾” Washers (#87), and M10 Aircraft Nuts (#89). DO NOT tighten
the Nuts and Bolts yet.
DIAGRAM 1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Place two ∅ 2 ½” Rubber Bumpers (#65) on the Rear Base Frame (#2). Align the holes
and insert Two Guide Rods (#18) through the holes into the Rear Base Frame. Secure
each Guide Rod with one M10 x 1” Allen Bolt (#75) and ∅ ¾” Washer (#87) from the
bottom of Rear Base Frame.
B.) Slide 14 Weight Plates (#48) onto the Guide Rods. Make sure all Plates are facing the
same direction. Insert the Selector Rod (#41) through the center hole on the Weight
Plates. Slide the Weight Selector Stem (#47) onto the Guide Rods.
C.) Use the L-shape Pin (#40) to select desired number of Weight Plates to Exercise. NOTE:
Each Plate weights 10 lbs. Please refer to the Weight Resistance Chart on page 24.
DIAGRAM 2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach the Upper Frame (#4) onto the two Guide Rods (#18). Secure each Guide Rod
to the Upper Frame with on M10 x 1” Allen Bolt (#75) and ∅ ¾” Washer (#87). DO NOT
tighten the Nuts and Bolts yet.
B.) Place the Upper Frame (#4) onto the top of the Vertical Frame (#5). Secure it with one
5 ½” x 2” Bracket (#27), two M10 x 2 ¾” Carriage Bolts (#72), two ∅ ¾” Washers (#87),
and two M10 Aircraft Nuts (#89).
C.) Securely tighten all Nuts and Bolts previously installed.
D.) Attach the Backrest Board (#22) to the Backrest Support Frame (#12). Secure it with
two M8 x 1 5/8” Allen Bolts (#82) and ∅5/8” Washers (#86).
E.) Attach the Backrest Support Frame (#12) to the Vertical Frame (#5). Secure it with one
M10 x 3 ½” Allen Bolt (#73), two ∅¾” Washers (#87), and one M10 Aircraft Nut (#89).
F.) Thread the Long T-shape Lock Pin (#43) into the hole on the Vertical Frame. Insert the
Pin into selected hole on the Backrest Support Frame to obtain the desired Backrest
position.
G.)Attach the Seat Support Frame (#6) to the Vertical Frame (#5). Secure it with one M10
x 2 ¾” Carriage Bolt (#72), ∅¾” Washer (#87), and M10 Aircraft Nut (#89).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 3
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach two Diagonal Support Frames (#7) to the Front Base Frame (#3). Secure it with
one M10 x 3” Carriage Bolt (#77), ∅ ¾” Washer (#87), and M10 Aircraft Nut (#89).
B.) Secure the two Diagonal Supports to the Seat Support Frame (#6) with one M10 x 3”
Carriage Bolt (#77), ∅¾” Washer (#87), and M10 Aircraft Nut (#89).
C.) Attach the Leg Developer (#8) to the top of the Diagonal Support Frames (#7). Secure
it with one M10 x 3” Allen Bolt (#74), two ∅ ¾” Washers (#87), and one M10 Aircraft
Nut (#89). Do not over tighten the Bolt. Make sure the Leg Developer is able to swivel.
D.) Attach the Front Press Base (#10) to the Upper Frame (#4). Align the holes and insert
the Front Press Base Axle (#31). Secure it with two M10 x ½” Allen Bolts (#85).
DIAGRAM 4
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the Front Press (#11) to the pivot on the Front Press Base (#10). Align the holes
and insert the Front Press Axle (#32) through the holes.
B.) Secure each end of the Axle with one M10 x ¾” Allen Bolt (#76) and ∅1 3/8” Washer
(#66). Secure the Axle to the Front Press with two M8 x ¾” Screws (#88).
C.) Thread a Short T-shape Lock Pin (#52) into the hole on the Front Press. Use the Lock Pin
to secure the desired Front Press exercise position.
D.) Attach the Butterfly Pulley Bracket (#17) to the Rear Base Frame (#2). Secure it with two
M10 x 2 ¾” Carriage Bolts (#72), ∅ ¾” Washers (#87), and M10 Aircraft Nuts (#89).
DIAGRAM 5
11
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6)
A.) Attach the Butterfly Base (#14) to the Vertical Frame (#5). Secure it with one 4 ¾” x 2”
Bracket (#26), two M10 x 3 ½” Carriage Bolts (#71), two ∅ ¾” Washers (#87), and two
M10 Aircraft Nuts (#89).
B.) Insert the Right Butterfly (#20) into the right pivot on Butterfly Base. Secure it with one M10
x ¾” Allen Bolt (#76) and ∅1 3/8” Washer (#66) from the bottom.
C.) Insert the Butterfly Handle (#13) into the pivot on the Right Butterfly. Secure it with one
M10 x ¾” Allen Bolt (#76) and ∅ 1 3/8” Washer (#66).
D.) Repeat Procedures B and C above to install the other side.
DIAGRAM 6
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7)
A.) Place the Seat Pad (#21) onto the Seat Post (#9). Secure it with two M8 x 1 5/8” Allen Bolts
(#82) and ∅ 5/8” Washers (#86).
B.) Insert the Seat Post into the opening on the Seat Support Frame (#6). Use a Lock Knob
(#44) to obtain the desired height of Seat.
C.) Insert two Foam Tubes (#28) halfway through the holes on Seat Post and Leg Developer.
Push four Foam Rolls (#64) onto the Tubes from both ends. Plug four Foam Roll End Caps
(#58) onto the Tubes.
DIAGRAM 7
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP DIAGRAM
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 8 (See Diagram 8 & Upper Cable Loop Diagram)
A.) Attach the 154” Upper Cable (#34) to the opening on the front Upper Frame (#4). Make
sure the ball stopper is underneath the Frame. Attach a Pulley (#45) to the Cable.
Secure the Pulley with one M10 x 2 ½” Allen Bolt (#78), two ∅ 5/8” x 5/8” Pulley
Bushings (#60), and one M10 Aircraft Nut (#89).
B.) Draw the Cable over the Pulley along the Upper Frame towards the back of the
machine to the opening in the middle of Upper Frame. Repeat Procedure B above to
install a Pulley.
C.) Draw the Cable around the Pulley then back to the upper open bracket on the back of
Front Press Base (#10). Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾”
Allen Bolt (#80), two ∅ ¾” Washers (#87), and one M10 Aircraft Nut (#89).
D.) Draw the Cable around the Pulley then towards the upper opening on the Vertical
Frame (#5). Repeat Procedure B above to install a Pulley.
E.) Draw the Cable around the Pulley and back to the lower open bracket on the back of
Front Press Base (#10). Repeat Procedure C above to install a Pulley.
F.) Draw the Cable around the Pulley then to the lower opening on the Upper Frame.
Repeat Procedure B above to install a Pulley.
G.) Draw the Cable underneath the Pulley then pull upward to the open bracket underneath
the Upper Frame. Repeat Procedure C above to install a Pulley.
H.) Draw the Cable around the Pulley then downward. Attach a Pulley to the two Double
Floating Pulley Brackets (#24). Repeat Procedure C above to install a Pulley. Let the
Bracket hanging for now.
I.) Draw the Cable around the Pulley then upward to the opening on the back of Upper
Frame. Repeat the Procedure C above to install a Pulley.
J.) Draw the Cable around the Pulley then downward to the Selector Rod (#41). Thread
the Head Bolt at end of the Cable into the Selector Rod.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 8
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Upper Cable Loop Diagram
17
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 9 (See Diagram 9 & Lower Cable Loop Diagram)
A.) Attach the 156” Lower Cable (#36) to the opening on the Leg Developer (#8). Attach a
Pulley to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#79), two ∅ 5/8” x
½” Pulley Bushings (#61), and one M10 Aircraft Nut (#89).
B.) Draw the Cable underneath the Pulley to the open bracket on the Front Base Frame
(#3). Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#80),
two ∅ ¾” Washers (#87), and one M10 Aircraft Nut (#89).
C.) Draw the Cable underneath the Pulley towards back of the machine through the
bottom openings on the Vertical Frame (#5) and Butterfly Pulley Bracket (#17) to the
open bracket on the Rear Base Frame (#2). Repeat Procedure B above to install a
Pulley with a L-shape Cable Bracket (#91).
D.) Draw the Cable underneath the Pulley then pull upward to the Double Floating Pulley
Bracket (#24) previously installed in STEP-8. Repeat the Procedure B above to install
a Pulley. After completing the entire cable system, come back to the Double Floating
Pulley Bracket and adjust the height of the lower Pulley to adjust the tightness of the
Cables.
E.) Draw the Cable around the Pulley then downward. Attach the Cable to an Angled
Double Floating Pulley Bracket (#23). Repeat Procedure B above to install a Pulley.
Let the Bracket hanging for now.
F.) Draw the Cable around the Pulley then upward to the opening on the Vertical Frame
(#5). Attach a Pulley to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#78),
two ∅ 5/8” x 5/8” Pulley Bushings (#60), and one M10 Aircraft Nut (#89).
G.)Insert the Cable through a Nylon Ball Stopper (#96). Attach the Cable to a U-shape
Cable Connector (#90). Secure it with one M10 x 1 3/8” Allen Bolt (#81), two ∅ ¾”
Washers (#87), and one M10 Aircraft Nut (#89).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 9
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Lower Cable Loop Diagram
20
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 10 (See Diagram 10 & Butterfly Cable Loop Diagram)
A.) Attach one end of the 87” Butterfly Cable (#35) to the open slot on Right Butterfly (#20).
B.) Draw the Cable to the open slot on the Butterfly Pulley Bracket (#17). Attach a Pulley to
the open slot. Secure the Pulley with one M10 x 1 ¾” Allen Bolt (#80), one L-shape
Cable Bracket (#91), two ∅ ¾” Washers (#87), and one M10 Aircraft Nut (#89).
C.) Draw the Cable underneath the Pulley then upward to the Angled Double Floating Pulley
Bracket (#23) previously installed in STEP-9. Install a Pulley.
D.) Draw the Cable around the Pulley then downward to the left open slot on the Butterfly
Pulley Bracket. Repeat the Procedure B above to install a Pulley.
E.) Pull the Cable ant attach it to the open slot on the Left Butterfly (#19).
DIAGRAM 10
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Butterfly Cable Loop Diagram
22
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 11 (See Diagram11)
A.) Connect the Lat Bar (#25) to the Upper Cable with two C-clips (#39) and one short Chain
(#38).
B.) Connect the Abdominal Strap (#95) to the mid Cable with a C-clip (#39).
C.) Connect the Shiver Bar (#29) to the Lower Cable with two C-clips (#39) and one Long
Chain (#37).
DIAGRAM 11
23
Download from Www.Somanuals.com. All Manuals Search And Download.
WEIGHT RESISTANCE CHART
WEIGHT PLATE
Station
Low Pulley
Lat Pull
1
2
3
4
5
6
7
8
9
22
30
10
20
22
33
40
16
34
33
38
44
50
22
48
44
50
55
60
28
62
55
62
66
70
34
76
66
74
77
80
40
88
99 110
90 100 110
46 52 58
Butterfly
Front Press
AB Crunch
90 104 118 132
77
86
88
99 110
Leg Developer 26
98 110 122
WEIGHT PLATE
13 14
Station
Low Pulley
Lat Pull
10 11
12
121 132 143 154 165
120 130 140 150 160
Butterfly
64
70
76
82
88
Front Press
AB Crunch
146 160 174 188 202
121 132 143 154 165
Leg Developer 134 146 158 170 182
*Numbers are approximate. Actual weight may vary.
*Value for butterfly is for each arm.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO. DESCRIPTION
Q’ty
1
1
Middle Base Frame
Rear Base Frame
Front Base Frame
Upper Frame
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
6” Front Press Handle Grip
Short T-shape Lock Pin
∅ 1 3/8” Bushing
4
1
2
2
4
5
1
4
2
10
2
10
4
4
2
6
2
2
2
1
2
9
1
1
4
6
2
5
1
12
1
4
2
1
2
2
3
4
1
1
1
1” x 2” End Cap
5
6
7
8
Vertical Frame
1
1
2
1
1
1
1
1
2
1
1
2
1
2
1
1
2” Square End Cap
1 ¾” Square End Cap
1 ½” Square End Cap
Foam Roll End Cap
∅ 1” End Cap
∅ 5/8” x 5/8” Pulley Bushing
∅ 5/8” x ½” Pulley Bushing
∅ 1 ½” Spacer
∅ 1” Spacer
Foam Roll
∅ 2 ½” Rubber Bumper
∅ 1 3/8” Washer
Seat Support Frame
Diagonal Support Frame
Leg Developer
Seat Post
Front Press Base
Front Press
Backrest Support Frame
Butterfly Handle
Butterfly Base
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Foot Plate
Anti Slip Sticker
Butterfly Pulley Bracket
Guide Rod
Left Butterfly Base
Right Butterfly Base
Seat Pad
∅ 1” Sleeve
∅ 1 7/8” Bushing
∅ 1” Rubber Bumper
∅ 1 ½” Rubber Bumper
M10 x 3 ½” Carriage Bolt
M10 x 2 ¾” Carriage Bolt
M10 x 3 ½” Allen Bolt
M10 x 3” Allen Bolt
M10 x 1” Allen Bolt
M10 x ¾” Allen Bolt
M10 x 3” Carriage Bolt
M10 x 2 ½” Allen Bolt
M10 x 2 3/8” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 1 3/8” Allen Bolt
M8 x 1 5/8” Allen Bolt
M10 x ¾” Allen Screw
M6 x 5/8” Philips Screw
M10 x ½” Allen Bolt
∅ 5/8” Washer
∅ ¾” Washer
M8 x ¾” Screw
M10 Aircraft Nut
U-shape Cable Connector
L-shape Cable Bracket
1” x 2” Slim End Cap
Single Handle
Ankle Strap
Abdominal Strap
1
1
Backrest Board
Angled Double Floating Pulley Bracket 1
Double Floating Pulley Bracket
Lat Bar
4 ¾” x 2” Bracket
5 ½” x 2” Bracket
Foam Tube
Shiver Bar Frame
Shiver Bar Handle
Front Press Base Axle
Front Press Axle
15 ¾” Foot Plate Axle
154” Upper Cable
87” Butterfly Cable
156” Lower Cable
Long Chain
Short Chain
C-clip
L-shape Pin
Selector Rod
Selector Rod Head Plastic Cover
Long T-shape Lock Pin
Lock Knob
Pulley
1 ¾” Square End Cap
Selector Stem
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
5
1
1
1
1
1
18
2
1
14
4
6
5
45
3
33
1
3
4
1
1
1
Nylon Ball Stopper
1
Weight Plate
2” Base Frame End Cap
5” Handle Grip
25
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing
or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Harbor Freight Tools Lathe 93212 User Manual
Harrington Hoists Saw EAC700 User Manual
Hasbro Robotics 30001 User Manual
HP Hewlett Packard Nail Gun 7 SNMP User Manual
HP Hewlett Packard Personal Computer 505B User Manual
HP Hewlett Packard Power Screwdriver 403606 10 User Manual
Husqvarna Chainsaw 1151322 95 User Manual
Husqvarna Snow Blower 524ST User Manual
Husqvarna Trimmer 227L LD User Manual
iLive Speaker IHS1 IHT3807DT User Manual