NOTE:
Please read all instructions
carefully before using this
product
MWM 900
HOME GYM
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWM 900
Retain This
Manual for
Reference
OWNER'S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY PRECAUTIONS
This gym built for optimum safety. However, certain precautions apply whenever you
operate a piece of exercise equipment. Be sure to read the entire manual before you
assemble or use your gym. In particular, note the following safety precautions:
1. Keep children and pets away from the gym at all times. Do not leave children unattended
in the same room with the gym. The gym is not a toy and therefore parents and guardians
should be aware of the natural tendency for children to play, leading to situations and
behaviour for which the gym is not intended.
2. If children are allowed to use the gym their physical/mental development and above all,
temperament should be taken into account. Constant supervision is therefore needed.
3. If the user experiences dizziness, nausea, chest pain or any other abnormal symptoms,
STOP the workout at once. Consult a physician immediately. Injuries may occur due to
incorrect or excessive exercise.
4. Position the gym on a clear levelled surface which is clear of all obstacles as not to restrict
movement whilst exercising. DO NOT use the gym near water or outdoors.
5. Keep hands away from all moving parts
6. Always wear appropriate clothing when exercising. DO NOT wear robes or other clothing
that could become caught in the gym. Running or aerobic shoes are also required when
using the gym.
7. Use the gym only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp objects around the gym.
9. Disabled persons should not use the machine without a qualified person or physician in
attendance.
10.
up.
Before using the gym to exercise, always do stretching exercises to properly warm
11.
12.
Never use the gym if it is not functioning properly.
This product is intended for H=Domestic use only.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN.
THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS
WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY
FITNESS EQUIPMENT. MARCY ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR
PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches.
NOTE: It is strongly recommended this machine to be assembled by two or more people to
avoid possible injury.
STEP 1 (See Diagram 1)
A)
B)
C)
Slide two Ø2 ½” Round Rubber Bumpers (#43) onto the Guide Rods (#7). Insert the two
Guide Rods into the holes on the Rear Stabilizer (#8). Secure each Guide Rod with one
M10 x 1” Allen Bolt (#72) and ∅ ¾” Washer (#77) from the bottom.
Attach the rear of Main Base Frame (#1) to the Rear Stabilizer. Secure them with two M10 x
2 ¾” Carriage Bolts (#62), one 4 3/8” x 2” Bracket (#20), two Ø ¾” Washers (#77), and two
M10 Aircraft Nuts (#81). Do not tighten the nuts and bolts yet.
Attach the Front Stabilizer (#19) to the Main Base Frame (#1). Secure them with one M10 x
3” Allen Bolt (#74), one 4” x 2” Bracket (#29), two Ø ¾” Washers (#77), and one M10
Aircraft Nut (#81) to the top hole. Secure the bottom hole with one M10 x 2 1/2” Allen Bolt
(#64) and ∅ 3/4” Washer (#77) from the back.
D)
E)
Attach the Foot Plates (#30) to the Front Stabilizer (#19). Secure them with two M10 x 2 ¾”
Carriage Bolts (#62), Ø ¾” Washers (#77), and M10 Aircraft Nuts (#81).
Place the Vertical Frame (#2) onto the Main Base Frame. Secure them with two M10 x 3 ½”
Carriage Bolts (#63), one Pulley Bracket (#18), two Ø ¾” Washers (#77), and two M10
Aircraft Nuts (#81). Securely tighten all nuts and bolts previously installed.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIARGRAM 1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A) Slide 9 Weight Plates (#37) onto the Guide Rods (#7). Align the holes on the Weight Plates.
Insert a Selector Rod (#21) through the center hole. Use a L-shaped Pin (#31) to select the
number of Weight Plates. Slide the Selector Stem (#36) onto the Guide Rods.
B) Attach the holes on the Upper Frame (#6) onto the Guide Rods. Place the Upper Frame onto
the Vertical Frame (#2).
C) Secure the Upper Frame (#6) to the Guide Rods (#7) with two M10 x 1” Allen Bolts (#72) and
Ø ¾” Washers (#77).
D) Secure the Upper Frame to the Vertical Frame with two M10 x 2 ¾” Carriage Bolts (#62),
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A) Place the Seat (#55) onto the Seat Support (#10). Secure it with two M8 x 1 5/8” Allen Bolts
(#69) and Ø 5/8” Washers (#78).
B) Insert the Seat Support into the opening on the Main Base Frame (#1). Use a Lock Knob
(#32) to secure the Seat Support at desired height.
C) Attach two ∅ 1” x ½” Bushings (#34) to the Leg Developer (#9). Attach the Leg Developer to
the bracket on the Main Base Frame. Secure it with one M12 x 3 1/8” Allen Bolt (#71), two Ø
1” Washers (#76), and one M12 Aircraft Nut (#80). Do not over tighten the Bolt and Nut. Make
sure the Leg Developer is able to swivel on the Bolt.
D) Insert two Foam Tubes (#40) halfway through the holes on the Seat Support and Leg
Developer. Push four Foam Rolls (#48) onto the Tubes from both ends. Cover each end with
a Foam Roll End Cap (#54).
DIAGRAM 3
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A) Attach the Front Press Base (#3) to the Upper Frame (#6). Secure it with one Axle (#24), two
Spacers (#79), and two M10 Aircraft Nuts (#81). Do not over tighten the Nuts.
B) Insert the axle on the Right Butterfly (#4) through the hole on the Front Press Base from the
bottom. Slide a Lock Ring (#60) onto the axle. Align the holes and secure it with one M6 x 1
5/8” Hex Bolt (#61) and M6 Aircraft Nut (#73). Repeat the same step to install the Left Butterfly
(#5).
C) Attach the Swivel Pulley Bracket Frame (#16) to the back of the Vertical Frame (#2). Secure it
with one M10 x 3 ½” Allen Bolt (#70), two Ø ¾” Washers (#77), and one M10 Aircraft Nut (#81).
D) Attach a Swivel Pulley Bracket (#17) to each end of Swivel Pulley Bracket Frame. Secure each
Bracket with one M10 x 2 ½” Allen Bolt (#64), two Ø ¾” Washers (#77), and one M10 Aircraft
Nut (#81).
E) Attach the Backrest Board (#56) to the Vertical Frame (#2). Secure it with two M8 x 2 ½” Allen
Bolts (#68) and Ø 5/8” Washers (#78).
DIAGRAM 4
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP DIAGRAM
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5 & Cable Loop Diagram)
A) Attach the 144” Upper Cable (#57) to the front opening on the Upper Frame (#6). NOTE:
The Ball Stopper on the Cable needs to be underneath the Frame. B.) Attach a Pulley
(#41) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#64), two Ø 7/8” Pulley
Bushings (#35), and one M10 Aircraft Nut (#81). C.) Draw the Cable towards the back of
the machine to another opening on the Upper Frame. Repeat Step B above to install a
Pulley.
B) Draw the Cable around the Pulley then pull back to the opening on the Front Press Base
(#3). Attach a Pulley to the opening. Secure it with one M10 x 5 ¾” Allen Bolt (#67), two Ø
¾” Washers (#77), and one M10 Aircraft Nut (#81).
C) Draw the Cable around the Pulley then through the hole on the Vertical Frame (#2) to the open
bracket on the back of Vertical Frame. F.) Attach a Pulley to the bracket. Secure it with one
M10 x 1 ¾” Allen Bolt (#65), two ∅ ¾” Washers (#77), and one M10 Aircraft Nut (#81).
D) Draw the Cable over the Pulley and pull the Cable downwards. Attach a Pulley to the upper
holes on the two Double Floating Pulley Brackets (#14). Repeat Step F above to install another
Pulley. Let the Bracket hanging for now.
E) Draw the Cable around the Pulley then pull upwards to the open bracket underneath the Upper
Frame. Repeat Step F above to install another Pulley. I.) Pull the Cable downwards between
the two Guide Rods to the Selector Rod (#21). Securely thread the bolt on the end of the Cable
into the Selector Rod.
F) Attach a 10-Joint Chain (#26) to the Cable using a C-clip (#28). Attach the Lat Bar (#11) to the
Chain using a C-clip. Adjust the length of Chain to obtain the desired Lat Bar exercise.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 5
14
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6 & Cable Loop Diagram
A) Attach one end of the 108” Butterfly Cable (#58) to the hook on the Right Butterfly (#4). Draw
the Cable towards the right open Swivel Pulley Bracket (#17).
B) Attach a Pulley (#41) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#65), two ∅ ¾”
Washers (#77), and one M10 Aircraft Nut (#81).
C) Draw the Cable over the Pulley then pull downward. Attach the Cable to an Angled Double
Floating Pulley Bracket (#15). Install a Pulley as described in Step B. Let the Bracket hanging
for now.
D) Draw the Cable around the Pulley and pull upward to the left open Swivel Pulley Bracket.
Install another Pulley as described in Step B above.
E) Draw the Cable over the Pulley and attach the end to the open hook on the Left Butterfly (#5).
F) Slide a Butterfly Foam Roll (#47) onto the Right Butterfly (#4). Attach a Front Press Handle
(#53) to the end of the tube and sure it with a M10 x 3 ½” Allen Bolt (#70). Repeat the same
15
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 7 (See Diagram 7 & Cable Loop Diagram)
A.) Attach the 144” Lower Cable (#59) to the opening on the bottom of the Leg Developer (#9).
B.) Attach a Pulley (#41) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#64), two ∅
7/8” Pulley Bushings (#35), and one M10 Aircraft Nut (#81).
C.) Draw the Cable underneath the Pulley towards the back of the machine through the opening on
the bottom of the Main Base Frame (#1) to an open bracket.
D.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#65), two Ø ¾”
Washers (#77), and one M10 Aircraft Nut (#81).
E.) Draw the Cable underneath the Pulley towards the back of the machine to the Pulley Bracket
(#18) underneath the Main Base Frame.
F.) Attach a Pulley to the bracket. Secure it with one L-shaped Bracket (#23), one M10 x 2” Allen
Bolt (#66), two ∅ ¾” Washers (#77), and one M10 Aircraft Nut (#81).
G.) Pull the Cable upward to the Angled Double Floating Pulley Brackets (#15) previously
installed in Step 6. Repeat Step D to install another Pulley.
H.) Draw the Cable around the Pulley then pull downward to the open bracket on the Main Base
Frame. Repeat Step D to install another Pulley.
I.) Draw the Cable around the Pulley then pull upward to the Double Floating Pulley Bracket (#14)
previously installed in Step-5. Repeat Step D to install a Pulley.
J.) Draw the Cable around the Pulley then pull downward to the bracket on the rear of Main Base
Frame. Attach the Cable to a 6-Joint Chain (#25) using a C-clip (#28). Secure the other end of
the Chain to the bracket with a M10 x 1” Allen Bolt (#72), two ∅ ¾” Washers (#77) and one
M10 Aircraft Nut (#81).
K.) Use the length of the Chain to adjust the tension of the Cable Loop System. If the Cables are
too loose, shorten the Chain.
L.) Attach the 15-Joint Chain (#27) to the end of the Cable by using a C-clip. Attach the Arm Curl
Handle (#12) to the Chain by using another C-clip. Replace Arm Curl Handle with the Ankle
Strap (#82) for various Leg exercises. Adjust the length of Chain to obtain the desired exercise.
Remove the Arm Curl Handle and Ankle Strap when using the Leg Developer.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 7
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO
DESCRIPTION
QTY
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
67.
68.
69.
70.
71.
72.
73.
74.
75.
76.
77.
78.
79.
80.
81.
82.
83.
84.
85.
Front Press Handle
Foam Roll End Cap
Seat
2
4
1
1
1
1
1
2
2
6
2
6
10
1
1
2
2
3
1
5
2
1
1
2
47
4
2
1.
2.
3.
4.
5.
6.
7.
8.
Main Base Frame
Vertical Beam
Front Press Base
Right Butterfly
Left Butterfly
Upper Frame
Guide Rod
Rear Stabilizer
Leg Developer
Seat Support
Lat Bar
Arm Curl Handle
Arm Curl Tube
Double Floating Pulley Bracket
Angled Double Floating Pulley Bracket
Swivel Pulley Bracket Frame
Swivel Pulley Bracket
Pulley Bracket
Front Stabilizer
4 3/8” x 2” Bracket
Selector Rod
4 ¾” x 2” Bracket
L-shaped Bracket
Axle
6-Joint Chain
10-Joint Chain
15-Joint Chain
C-clip
4” x 2” Bracket
Foot Plate
L-shaped Pin
Lock Knob
Ø 1” x 5/8” Bushing
Ø 1” x ½” Bushing
Ø 7/8” Pulley Bushing
Selector Stem
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
5
1
2
1
1
6
2
6
1
9
2
2
2
15
1
2
1
4
2
2
4
3
7
4
3
Backrest Board
144” Upper Cable
108” Butterfly Cable
144” Lower Cable
Lock Ring
M6 x 1 5/8” Hex Bolt
M10 x 2 ¾” Carriage Bolt
M10 x 3 ½” Carriage Bolt
M10 x 2 ½” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 2” Allen Bolt
M10 x 5 ¾” Allen Bolt
M8 x 2 ½” Allen Bolt
M8 x 1 5/8” Allen Bolt
M10 x 3 ½” Allen Bolt
M12 x 3 1/8” Allen Bolt
M10 x 1” Allen Bolt
M6 Aircraft Nut
M10 x 3” Allen Bolt
M6 x 5/8” Philips Screw
Ø 1” Washer
Ø ¾” Washer
Ø 5/8” Washer
Spacer
M12 Aircraft Nut
M10 Aircraft Nut
Ankle Strap
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
1
30
1
#5 Allen Wrench (Tool)
#6 Allen Wrench (Tool)
#8 Allen Wrench (Tool)
Weight Plate
Ø 1 1/8” Bushing
Ø 1 ½” Bushing
Foam Tube
Pulley
1 7/8” Rubber Bumper
Ø 2 ½” Round Rubber Bumper
∅ 1 ½” Rubber Bumper
5 ½” Handle Grip
6” Lat Bar Handle Grip
Butterfly Foam Roll
Foam Roll
2” Square Stabilizer End Cap
2” Square End Cap (Impex Logo)
2” x 1” End Cap
Ø 1” End Cap
18
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Escalade warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the frame and one year on
all other parts and components from the date of purchase. This warranty extends only to the
original purchaser. Escalade’s obligation under this Warranty is limited to replacing damaged
or faulty parts at Escalade’s option.
All returns must be pre-authorised by Escalade. This warranty does not extend to any
product or damage to a product caused by or attributable to freight damage, abuse, misuse,
improper or abnormal usage, purchasers own repairs or for products used for commercial or
rental purposes. No other warranty beyond that specifically set forth above is authorized by
Escalade.
Escalade is not responsible or liable for indirect, special or consequential damages arising
out of or in connection with the use or performance of the product or other damages with
respect to any economic loss, loss of property, loss of revenues or profits, loss of
enjoyments or use, costs of removal, installation or other consequential damages or
whatsoever natures.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and
duration to the terms set forth herein.
Your statutory rights are not affected.
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department Monday to
Friday 8am to 4:30pm.
Tel / Fax: 0044 (0) 1792 702610
When ordering replacement parts, please give the following information.
1. Model
2. Description of Parts
3. Part Number
4. Date of Purchase
20
Download from Www.Somanuals.com. All Manuals Search And Download.
.CARE AND MAINTENANCE
1.
2.
Inspect and tighten all parts before using the gym.
The gym can be cleaned using a damp cloth and mild non-abrasive detergent. DO NOT
use solvents.
3.
4.
Examine the gym regularly for signs of damage or wear. Pay particular attention to the
bushings on movable parts.
Examine the cables regularly for signs of wear and damage. Adjust cable tension as
required. This can be achieved by moving the C Clip up one link on Chain #25.
Failure to examine the gym regularly may affect the safety level of the equipment.
Periodically, spray the Guide Rods # 7 with silicon spray or light oil to ensure a smooth
operation.
5.
6.
7.
8.
Replace any defective components immediately and/or keep the gym out of use until
repair.
Ensure Lat Bar #11 is properly stored when not in use.
Dimensions: H: 211cm x W: 100cm x L: 170cm
21
Download from Www.Somanuals.com. All Manuals Search And Download.
|