NOTE:
Please read all instructions
carefully before using this
product
DELUXE SMITH MACHINE
Table of Contents
Safety Notice
MSS-1280
Hardware Identifier
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MSS-1280
Retain This
Manual for
Reference
08-03-09
OWNER'S
MANUAL
IMPEX® INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Lubricate moving parts and Guide Rods with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.
5. Maximum weight on the Sliding Weight Post: 300 lbs.
6. Maximum weight on Leg Developer: 100 lbs.
7. Maximum weight on Weight Bar: 300lbs.
8. Maximum weight Capacity: 600 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF
THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL PLACEMENT
The warning labels shown here have been placed on the back of Rear Support, and Upper Frame. If the
labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the
labels in the location shown.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CAGE MACHINE HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE ASSEMBLY INSTRUCTION
Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended that two or more people assemble this machine
to avoid possible injury.
STEP 1 (See Diagram 1)
A.) Note: Do not tighten the Nuts and Bolts until instructed to do so.
B.) Connect the two Base Frames (#3) by the Cross Brace (#7). Secure each end of the
Cross Brace to each Base Frame with four M10 x 2 3/8” Carriage Bolts (#50), one 4 ¾”
x 3 ¼” Bracket (#22), four Ø ¾” Washers (#57), and four M10 Aircraft Nuts (#58).
C.) Attach the Left Rear Support (#5) onto the left Base Frame. Secure it with two M10 x 3
½” Allen Bolts (#55), four Ø ¾” Washers (#57), and two M10 Aircraft Nuts (#58).
Repeat the same step to install the Right Rear Support (#6) onto the other Base
Frame.
DIAGRAM 1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Do not tighten Nuts and Bolts until instructed to do so.
B.) Attach the Left Upright Beam (#1) to the Left Rear Support (#5) and onto the left
Base Frame (#3).
C.) Secure it to the Base Frame with two M10 x 4” Allen Bolts (#54), four Ø ¾”
Washers (#57), and two M10 Aircraft Nuts (#58).
D.) Secure it to the Left Rear Support with one M10 x 4” Carriage Bolt (#48), one Ø
¾” Washer (#57), and one M10 Aircraft Nut (#58) from side. Secure with one M10
x 5/8” Allen Bolt (#63) and one Ø ¾” Washer (#57) from top.
E.) Repeat A to D to install the Right Upright Beam (#6) to the right Base Frame.
F.) Attach the Top Beam (#4) to the Left & Right Upright Beam. Secure each end of
the Top Beam to each Upright Beam with one 4” x 2 3/8” Curved Bracket (#23),
one M10 x 4 1/8” Allen Bolt (#53) and one Ø ¾” Washer (#57) to the upper hole,
one M10 x 4 1/8” Carriage Bolt (#49), one Ø ¾” Washers (#57), and one M10
Aircraft Nut (#58) to the lower hole.
G.)Slide Lower Left Safety Stop Frame (#9) onto a Guide Rod (#11). Slide one
Safety Stop Frame (#18) onto the Guide Rod. Insert the bottom of the Guide Rod
into the hole on the left Base Frame. Attach the top of the Guide Rod to the
bracket on Left Upright Beam. Secure each end of Guide Rod with one M10 x ¾”
(#56) and one Ø ¾” Washer (#57). Repeat the same step to install the Lower
Right Safety Stop Frame (#10), the other Safety Stop Frame, and the other Guide
Rod to the other side.
H.) Turn and attach the hooks on the Lower Left & Right Safety Stop Frame to the
selected slot on Left & Right Upright Beam (#1 & #2).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 2
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Attach two Ø 2 3/8” x 2” Rubber Bumpers (#30) to the holes on the Cross Brace (#7). Insert
the two Rear Short Guide Rods (#17) through the two Rubber Bumpers into the holes on
Cross Brace.
B.) Secure each Guide Rod to the Cross Brace with one M10 x ¾” Allen Bolt (#56) and one Ø
¾” Washer (#57) from bottom.
C.) Slide the Sliding Weight Post (#16) onto the two Rear Short Guide Rods. Make sure the
Pulley bracket on the Weight Sliding Frame faces upward.
D.) Attach the Rear Upper Frame (#15) to the two Rear Short Guide Rods. Secure each Guide
Rod to the Rear Upper Frame with one M10 x ¾” Allen Bolt (#56) and one Ø ¾” Washer
(#57).
E.) Attach the front of Rear Upper Frame to the Top Beam (#4). Attach the Front Upper Frame
(#14) to the Top Beam from front. Align the holes. Secure them together with two M10 x 2
¾” Carriage Bolts (#47), two Ø ¾” Washers (#57), and two M10 Aircraft Nuts (#58).
F.) Securely tighten all Nuts and Bolts installed in Step-1, Step-2, and Step-3.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM 3
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLE LOOP DIAGRAM
11
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4 & Cable Loop Diagram)
A.) Attach the 170” Upper Cable (#25) to the opening on the Front Upper Frame (#14).
B.) Attach a Pulley (#33) to the opening. Secure it with one M10 x 4” Allen Bolt (#54), two
Ø ¾” Washers (#57), and one M10 Aircraft Nut (#58).
C.) Draw the Cable over the Pulley toward the back of the machine. Note: The Ball
stopper on the Cable needs to be under the Frame.
D.) Draw the Cable to the first opening on the Rear Upper Frame. Repeat B to install a
Pulley.
E.) Draw the Cable around the Pulley then downward to the open Pulley bracket on the
Sliding Weight Post (#16).
F.) Attach a Small Pulley (#32) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt
(#52), two Ø ¾” Washers (#57), and one M10 Aircraft Nut (#58).
G.) Draw the Cable around the Pulley then upward to the rear opening on the Rear Upper
Frame. Repeat B to install a Pulley.
H.) Draw the Cable around the Pulley and let the Cable hanging just for now.
I.) Connect the Lat Bar (#21) to the ball stopper on the Cable with two Hooks (#36) and
one 10-link Chain (#43).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5 & Cable Loop Diagram)
A.) Attach the 62” Lower Cable (#26) to the open bracket on the Cross Brace (#7). Attach
a Pulley (#33) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#52), two Ø ¾”
Washers (#57), one L-shaped Cable Retainer (#24), and one M10 Aircraft Nut (#58).
B.) Draw the Cable underneath the Pulley then upward to the 170” Upper Cable (#25)
installed in Step-4.
C.) Connect the Lower Cable to a Hook (#36). Connect the Hook to the 5-link Chain
(#44). Secure the 5-link Chain to the end of Upper Cable with one M10 x 1” Allen Bolt
(#51), two Ø ¾” Washers (#57, and one M10 Aircraft Nut (#58). Adjust the tension of
the Cable system by moving the Hook position to the Chain. If the tension is too loose
then move the hook up the chain. If the tension is too tight then move down the Hook.
D.) Connect the Shiver Bar (#21) to the ball stopper on Lower Cable with two Hooks (#36)
and one 15-link Chain (#42).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6 (See Diagram 6)
A.) Place the Lifting Sleeve (#8) in between the two Safety Stop Frames (#18). Align the
holes. Insert the Weight Bar (#13) from outside of one Safety Stop Frame through the
Lifting Sleeve to the other Safety Stop Frame on the other side.
B.) Turn and attach the two safety catch hooks on the Lifting Sleeve (#8) to the selected slots
on the Left and Right Uptight Beams (#1 & #2).
C.) Attach two Weight Bar Sleeves (#35) onto the Weight Bar from both ends. Attach two
Spring Clips (#62) to the Sleeves.
D.) Attach four Weight Posts (#12) into the holes on Left & Right Rear Support (#5 & #6).
Secure each Weight Post to the Support with one M10 x ¾” Allen Bolt (#56) and one Ø ¾”
Washer (#57). Slide four Olympic Sleeves (#34) to the four Weight Posts. Attach four
Spring Clips to the Sleeves.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE EXPLODED DIAGRAM
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SMITH MACHINE PART LIST
KEY NO. DESCRIPTION
Q’ty
1
1
2
1
1
1
1
1
1
1
2
4
1
1
1
1
2
2
1
1
2
2
2
1
1
1
2
4
2
2
2
1
4
6
2
5
8
2
8
1
1
1
1
1
4
12
2
2
2
8
1
2
3
Left Upright Beam
Right Upright Beam
Base Frame
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
M10 x 1” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 4 1/8” Allen Bolt
M10 x 4” Allen Bolt
M10 x 3 ½” Allen Bolt
M10 x ¾” Allen Bolt
Ø ¾” Washer
M10 Aircraft Nut
ST3.8 Philips Screw
Rivet
M8 x 3/8” Allen Bolt
Spring Clip
M10 x 5/8” Allen Bolt
Ø 7/8” x ¾” End Cap
Ø 5/8” End Cap
1
2
2
7
4
Top Beam
5
6
7
Left Rear Support
Right Rear Support
Cross Brace
4
12
58
28
24
8
2
8
2
8
Lifting Sleeve
9
Lower Left Safety Stop Frame
Lower Right Safety Stop Frame
Guide Rod
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Weight Post
Weight Bar
Front Upper Frame
Rear Upper Frame
Sliding Weight Post
Rear Short Guide Rod
Safety Stop Frame
Lat Bar
18
18
2
Ø ¾ End Cap
Shiver Bar
Rotate Ring
4 ¾” x 3 ¼” Bracket
4” x 2 3/8” Curved Bracket
L-shaped Cable Retainer
170” Upper Cable
62” Lower Cable
Ø 3 ½” Upright Beam End Cap
1 5/8” x 3 1/8” End Cap
Ø 3” Upper Frame End Cap
Ø 2 3/8” x 2” Rubber Bumper
Ø ¾” x 2” Cover
Small Pulley
Pulley
Olympic Sleeve
Weight Bar Sleeve
Hook
Ø 1” End Cap
Ø 1 ¾” End Cap
Plastic Ring
Ankle Strap
Single Handle
15-link Chain
10-link Chain
5-link Chain
6” Grip
Sliding Sleeve
M10 x 2 ¾” Carriage Bolt
M10 x 4” Carriage Bolt
M10 x 4 1/8” Carriage Bolt
M10 x 2 3/8” Carriage Bolt
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BENCH HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
BENCH HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
BENCH ASSEMBLY INSTRUCTION
STEP 1 (See Diagram 1)
A.) Attach the Bench Base Frame (#6) to the Rear Stabilizer (#7). Secure the side-holes
with two M10 x 4” Carriage Bolts (#41), two Ø ¾” Washers (#31), and two M10
Aircraft Nuts (#33). Secure the top hole with one M10 x 5/8” Allen Bolt (#36) and one
Ø ¾” Washer (#31).
B.) Attach the Wheel Set (#25) to the bracket on Rear Stabilizer. Secure it with one M8 x
5 1/8” Allen Bolt (#35), two Ø 5/8” Washers (#30), and one M8 Aircraft Nut (#32)
DIAGRAM 1
19
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the Main Seat Support (#1) to the Bench Base Frame (#6). Secure it with three M10 x 4”
Carriage Bolts (#41), three Ø ¾” Washers (#31), and three M10 Aircraft Nuts (#33).
B.) Attach the Front & Rear Seat Bracket (#4 & #5) to Main Seat Support. Secure each Bracket
with one M10 x 4” Allen Bolt (#40), two Ø ¾” Washers (#31), and one M10 Aircraft Nut (#33).
DIAGRAM 2
20
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 (See Diagram 3)
A.) Align the bracket on the Backrest Adjustment Support (#8) in between the two Backrest
Supports (#3). Secure it with four M8 x 1 5/8” Allen Bolts (#34), eight Ø 5/8” Washers (#30),
and four M8 Aircraft Nuts (#32). Do not tighten the Nuts and Bolts yet.
B.) Insert the Backrest Adjustment Support into the opening on the Main Seat Support (#1).
Press or step down on the Backrest Adjustment Lever (#9) to allow the Support to go
through.
C.) Attach the bottom side-holes on the two Backrest Supports to the pivot on the Main Seat
Support. Secure it with one M10 x 6 ½” Allen Bolt (#39), two Ø ¾” Washers (#31), and one
M10 Aircraft Nut (#33).
D.) Securely tighten all Nuts and Bolts in B & C.
E.) Do not over tighten the Nut and Bolt in C.
F.) Make sure the Backrest Supports are able to swivel.
DIAGRAM 3
21
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4 (See Diagram 4)
A.) Attach the Backrest Board (#13) to the Backrest Supports (#3). Secure it with four M8 x 1
5/8” Allen Bolts (#34) and four Ø 5/8” Washers (#30).
B.) Attach the Seat Pad (#12) to Front & Rear Seat Bracket (#4 & #5). Secure them with four M8
x 1 5/8” Allen Bolts (#34) and four Ø 5/8” Washers (#30).
C.) Pull up the Backrest Adjustment Support (#8) or press down the Backrest Adjustment Lever
(#9) to adjust the Backrest incline position.
DIAGRAM 4
22
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5 (See Diagram 5)
A.) Attach the Leg Developer (#2) to Main Seat Support (#1). Secure it with one M10 x 3 1/8”
Allen Bolt (#38), two Ø ¾” Washers (#31), and one M10 Aircraft Nut (#33).
B.) Insert two Foam Tubes (#10) halfway through the holes on Leg Developer. Push four Foam
Rolls (#16) onto the Tubes from both ends. Plug four Foam Roll End Caps (#17) into the
ends.
C.) Slide an Olympic Sleeve (#28) on the weight post on Leg Developer. Attach a Spring Clip
(#27) to the Sleeve.
DIAGRAM 5
23
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
BENCH PARTS LIST
KEY NO. DESCRIPTION
Q’ty
1
1
1
Main Seat Support
Leg Developer
2
3
4
5
6
Backrest Support
Front Seat Bracket
Rear Seat Bracket
Bench Base Frame
Rear Stabilizer
2
1
1
1
7
1
8
Backrest Adjustment Support 1
9
Backrest Adjustment Lever
Foam Tube
Spring
Seat Pad
Backrest Board
2 ¾” Grip
2” x 1 5/8” Rubber Bumper
Foam Roll
Foam Roll End Cap
1 5/8” x 3 1/8” End Cap
1” Square End Cap
Ø 1” End Cap
Ø 2” End Cap
Base Frame End Cap
Rear Stabilizer Left End Cap
Rear Stabilizer Right End Cap 1
Wheel Set
Lever Cover
Spring Clip
Olympic Sleeve
Ø ¾” Leg Developer Bushing 2
Ø 5/8” Washer
1
2
1
1
1
1
1
4
4
1
6
2
3
1
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
1
1
1
1
18
16
5
10
12
1
1
1
1
1
Ø ¾” Washer
M8 Aircraft Nut
M10 Aircraft Nut
M8 x 1 5/8” Allen Bolt
M8 x 5 1/8” Allen Bolt
M10 x 5/8” Allen Bolt
M10 x 2 ½” Allen Bolt
M10 x 3 1/8” Allen Bolt
M10 x 6 ½” Allen Bolt
M10 x 4” Allen Bolt
M10 x 4” Carriage Bolt
2
5
25
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX® INC.
LIMITED WARRANTY
®
IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing
or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that
specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or other damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures.
Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
®
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|