NOTE:
Please read all
instructions carefully
before using this product
IRON GRIP STRENGTH
WEIGHT BENCH
IGS-8858
Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
IGS 8858
Retain This
Manual for
Reference
07/25/06
IMPEX® INC.
14777 Don Julian Rd., City of Industry, CA 91746
Tel: (800) 999-8899 Fax (626) 961-9966
OWNER'S
MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:
1. Keep children and pets away from the machine at all times. DO NOT leave children
unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine near water or
outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or other
clothing that could become caught in the machine. Running or aerobic shoes are also
required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or physician in
attendance.
10. Before using the machine to exercise, always do stretching exercises to properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
13. Maximum user’s weight: 300 lbs.
14. Maximum weight on uprights: 600 lbs.
15. Maximum weight on leg developer: 100 lbs.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT
YOUR PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS
OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH
PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE
OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING LABEL REPLACEMENT
The Warning Label shown here has been placed on the Cross Brace. If the label is
missing or illegible, please call customer service at 1-800-999-8899 for replacement.
Apply the label in location shown
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE PACK
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen
Wrenches. NOTE: It is strongly recommended two or more people assembling this
machine to avoid possible injury.
STEP 1
(See Diagram 1)
A.) Connect the Left & Right Upright Beam (# 1 & #2) by a Cross Brace (#4) in the mid span.
Secure them with M10 x 3 ¾” Carriage Bolts (#40), one 5 ½” Bent Bracket (#16), two ∅ ¾”
Washers (#49), and two M10 Aircraft Nuts (#52) on each side.
B.) Insert two Crutches (#6) into the top openings on the top of Left & Right Upright Beams.
Insert two M18 Lock Knobs (#31) through selected holes to obtain desired height.
C.) Place the Backrest Adjustment Bar (#5) on the selected slot on the Upright Beams to
obtain the desired backrest incline.
DIAGRAM 1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2 (See Diagram 2)
A.) Attach the front of Main Seat Support (#3) to the Front Post (#9). Secure it with two
M10 x 3 1/8” Carriage Bolts (#41), one 6 ¼” Bent Bracket (#18), two Ø ¾” Washers
(#49), and two M10 Aircraft Nuts (#52).
B.) Attach the Main Seat Support to the top of Front Post. Secure it with two M10 x 3 1/8”
Carriage Bolts (#41), one 4 ¾” Bent Bracket (#17), two Ø ¾” Washers (#49), and two
M10 Aircraft Nuts (#52).
C.) Attach the Main Seat Support to the Cross Brace (#4). Secure it with two M10 x 3 1/8”
Carriage Bolts (#41), two Ø ¾” Washers (#49), and two M10 Aircraft Nuts (#52) from
top. Secure it with two M10 x 3 3/8” Carriage Bolts (#58), one 4 ¾” Bent Bracket (#17),
two Ø ¾” Washers (#49), and two M10 Aircraft Nuts (#52) from the side.
DIAGRAM 2
7
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3
(See Diagram 3)
A.) Attach the Backrest Incline Support (#13) to the side-holes on the two Backrest Supports
(#12). Align the holes. Secure it with one M12 x 7 ¼” Allen Bolt (#43), two Ø ¾” Washers
(#49), and one M12 Aircraft Nut (#52).
B.) Attach the holes on the end of the Backrest Supports (#12) to the pivot on the Main Seat
Support (#3). Attach the two ends of the Seat Support (#11) to the two holes on end of
Backrest Supports. Align the holes. Secure them together with one M12 x 7 5/8” Allen Bolt
(#42), two Ø 1” Washers (#48), and one M12 Aircraft Nut (#51).
C.) Do not over tighten the Nuts and Bolts. Make sure the Backrest Supports and Backrest
Incline are able to swivel.
D.) Place the other ends of Seat Support onto the Main Seat Support. Use a 4” Lock Pin (#54)
through the hole on Seat Support under the Main Seat Support to secure the incline of the
Seat.
E.) Insert the Arm Curl Stand (#7) into the opening on Main Seat Support. Use a M10 Lock
Knob (#32) to lock the Stand at desired height.
DIAGRAM 3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4
(See Diagram 4)
A.) Attach the Backrest Board (#20) to the Backrest Supports (#12). Secure it with four M8 x 1
5/8” Allen Bolts (#45) and four Ø 5/8” Washers (#50).
B.) Place the Seat (#21) onto the Seat Support (#11). Secure it with four M8 x 1 5/8” Allen
Bolts (#45) and four Ø 5/8” Washers (#50).
C.) Attach the Arm Curl Pad (#22) to the Arm Curl Bracket (#55). Secure it with two M8 x 5/8”
Allen Bolts (#46) and two Ø 5/8” Washers (#50).
D.) Attach the Arm Curl Bracket to the bracket on the Arm Curl Stand (#7). Insert the M8 x 3
½” Allen Bolt (#56) through the open track on the Arm Curl Stand and the holes on the
Arm Curl Bracket. Secure the Bolt with two Ø 5/8” Washers (#50) and one M8 Aircraft Nut
(#57). Do not over tighten the Nut and Bolt. The Bolt needs to be able to slide on the track
freely.
DIAGRAM 4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5
(See Diagram 5)
A.) Attach the Leg Developer (#8) to the Main Seat Support. Secure it with an Axle (#26), two
M10 x 5/8” Allen Bolts (#44), and two Ø ¾” Washers (#49).
B.) Insert two Foam Tubes (#19) halfway through the holes on the Leg Developer. Push four
Foam Rolls (#29) onto the Tubes from both ends. Plug four Foam Roll End Caps (#33)
into the ends.
C.) Slide an Olympic Sleeve (#30) onto the weight post on Leg Developer. Attach a Spring
Clip (#25) onto the Sleeve.
D.) Attach the Arm Curl Handle to the back hole on the Leg Developer. Secure it with one 3”
Lock Pin (#28). Attach the Abdominal Strap (#53) to the front hole on Leg Developer.
Secure it with one 3” Lock Pin (#28).
E.) Pull up and flip the Arm Curl Pad along the track to face the back when doing Abdominal
exercises using the Abdominal Strap.
F.) Remove the Arm Curl Stand, Arm Curl Hand, and Abdominal Strap when doing Leg
Developer exercises.
DIAGRAM 5
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY NO.
1
2
3
4
5
6
7
8
DESCRIPTION
Left Upright Beam
Right Upright Beam
Main Seat Support
Cross Brace
Backrest Adjustment Bar
Crutch
Arm Curl Stand
QUANTITY
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
2
2
1
2
1
1
1
1
2
1
1
4
2
4
1
2
1
4
2
1
1
4
2
2
4
6
1
1
2
8
2
2
2
16
12
1
13
1
1
1
1
1
2
Leg Developer
Front Post
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
Arm Curl Handle
Seat Support
Backrest Support
Backrest Incline Support
Abdominal Strap Connector
Strap Buckle
5 ½” Bent Bracket
4 ¾” Bent Bracket
6 ¼” Bent Bracket
Foam Tube
Backrest Board
Seat
Arm Curl Pad
2 3/8” x 2” Sleeve
9 ½” x Ø 3” Crutch Sleeve
Spring Clip
Axle
Ø 1” Bushing
3” Lock Pin
Foam Roll
Olympic Sleeve
M18 Lock Knob
M10 Lock Knob
Foam Roll End Cap
Ø 2 3/8” Leg Developer Bushing
∅ 1” End Cap
Ø 1” Cone-shaped End Cap
1” Square End Cap
Ø 2” End Cap
6” Arm Curl Handle Grip
M10 x 3 ¾” Carriage Bolt
M10 x 3 1/8” Carriage Bolt
M12 x 7 5/8” Allen Bolt
M10 x 7 ¼” Allen Bolt
M10 x 5/8” Allen Bolt
M8 x 1 5/8” Allen Bolt
M8 x 5/8” Allen Bolt
ST4 Philips Screw
∅ 1” Washer
∅ ¾” Washer
Ø 5/8” Washer
M12 Aircraft Nut
M10 Aircraft Nut
Abdominal Strap
4” Lock Pin
Arm Curl Bracket
M8 x 3 ½” Allen Bolt
M8 Aircraft Nut
M10 x 3 3/8” Carriage Bolt
12
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPEX INC.
LIMITED WARRANTY
®
IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal
use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty
extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing,
at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer
Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the
customer. This warranty does not extend to any product or damage to a product caused by or attributable to
freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by a IMPEX authorized
service center or for products used for commercial or rental purposes. No other warranty beyond that specifically
set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or other damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential
damages or whatsoever natures.
Some states do not allow the exclusion or limitation of incidental or
consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may
not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
®
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899 during
our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|