Model No. IMTL59105.0
Serial No.
USER'S MANUAL
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-800-753-4645
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
free telephone number on the front cover of
this manual and order part number 146148, or
see your local electronics store.
2. Use the treadmill only as described.
12. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
which may result in a fall and serious injury.
13. Keep the power cord and the surge suppres-
sor away from heated surfaces.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 22 if the treadmill is
not working properly.)
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
15. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
7. The treadmill should be used only by persons
weighing 300 pounds or less.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
8. Never allow more than one person on the
treadmill at a time.
17. The pulse sensors are not medical devices.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensors are intended
only as exercise aids in determining heart
rate trends in general.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off cir-
cuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
10. When connecting the power cord (see page
11), plug the power cord into a surge sup-
pressor (not included) and plug the surge
suppressor into a grounded circuit capable of
carrying 15 or more amps. No other appliance
should be on the same circuit. Do not use an
extension cord.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 20.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
11. Use only a single-outlet surge suppressor
that meets all of the specifications described
on page 11. To purchase a surge suppressor,
see your local IMAGE dealer or call the toll-
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
treadmill, and before performing the mainte-
nance and adjustment procedures described in
this manual. Never remove the motor hood un-
less instructed to do so by an authorized ser-
vice representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
21. Inspect and properly tighten all parts of the
treadmill regularly.
22. Never insert any object into any opening.
24. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
23.
DANGER:
Always unplug the power
cord immediately after use, before cleaning the
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on your treadmill.
If a decal is missing, or if it is not legible, please call the
toll-free telephone number on the front cover of this manual
and order a free replacement decal. Apply the decal in the
location shown. Note: The decals are not shown at actual
size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the new IMAGE® 19.0 R tread-
mill. The 19.0 R treadmill offers an impressive array of
features designed to help you achieve your fitness
goals in the convenience and privacy of your home.
And when you’re not exercising, the unique 19.0 R
treadmill can be folded up, requiring less than half the
floor space of other treadmills.
number and serial number before calling. The model
number of the treadmill is IMTL59105.0. The serial
number can be found on a decal attached to the tread-
mill (see the front cover of this manual for the location).
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
For your benefit, read this manual carefully before
you use the treadmill. If you have questions after
reading this manual, please see the front cover of this
manual. To help us assist you, note the product model
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Fan
Water Bottle Holder
(no bottle is included)
Console
Handrail
Key/Clip
Storage Latch
Upright
Reset/Off
Circuit Breaker
Power Cord
Walking Belt
Foot Rail
Cushioned Walking Platform
for maximum exercise comfort
RIGHT SIDE
BACK
Rear Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480.
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is
coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the
top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-
mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included allen wrench
cutters , adjustable wrench
and your own phillips screwdriver
, and rubber mallet
, wire
.
Use the drawings below to identify the hardware used during assembly. Note: If a part is not in the parts bag,
check to see if it has been preattached to one of the parts to be assembled.
Silver Ground
Screw (94)–1
Screw (3)–11
1” Tek Screw (83)–4
Wheel Bolt (81)–2
Handrail Star
Washer (89)–4
Upright Star
Washer (67)–4
Handrail Bolt (64)–4
Wheel Spacer
(97)–4
Upright Bolt (65)–4
Wheel Nut (32)–2
1. Make sure that the power cord is unplugged.
1
58
84
With the help of a second person, carefully tip the
treadmill onto its left side as shown. Partially fold the
Frame (58) so the treadmill is more stable. Do not fully
fold the treadmill until it is completely assembled.
44
82
82
83
Press a Base Endcap (44) into the indicated end of the
Upright Base (84). Make sure that the Base Endcap is
oriented as shown in the inset drawing. If necessary, use
a rubber mallet to insert the Base Endcap.
83
Attach two Base Pads (82) to the Upright Base (84) with
two 1” Tek Screws (83).
44
84
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Attach a Wheel (80) and two Wheel Spacers (97) to the
Upright Base (84) with a Wheel Bolt (81) and a Wheel Nut
(32) as shown. Do not overtighten the Wheel Nut; the
Wheel should turn freely.
2
84
81
97
80
32
97
3. Identify the Right Upright (14).
3
77
Straighten the Upright Wire Harness (77), and feed it into
the lower end of the Right Upright (14) and out of the hole
shown in the inset drawing. Next, hold the Right Upright
against the right side of the Upright Base (84); make sure
that the Right Upright is turned so that the upper end
is angled in the direction shown. Hand tighten two
Upright Bolts (65) with two Upright Star Washers (67) into
the Upright Base and the Right Upright; be careful not to
damage the Upright Wire Harness. Do not tighten the
Upright Bolts yet.
14
77
44
67
14
82
84
With the help of a second person, carefully tip the tread-
mill onto its other side. Attach the other Base Endcap (44)
and two Base Pads (82) as described in step 1. Next, at-
tach the other Wheel (80) as described in step 2. Then,
attach the Left Upright (not shown) as described above.
Note: There is not a wire harness on the left side.
65
80
82
4. With the help of a second person, carefully raise the
Uprights (14, 13 [not shown]) to a vertical position.
4
64
89
Hold the Handrail (20) near the Right Upright (14). Insert
the Upright Wire Harness (77) into the hole in the bottom
of the Handrail and out of the top as shown.
89
20
77
Next, set the Handrail (20) on the Right Upright (14) and
the Left Upright (not shown). Do not let the Upright Wire
Harness (77) fall into the Right Upright.
Attach the Handrail (20) with four Handrail Bolts (64)
(only two are shown) and four Handrail Star Washers
(89); start all four Handrail Bolts, slide the Handrail
upward, and then firmly tighten the Handrail Bolts.
14
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. While a second person holds the console assembly near
the Handrail (20) as shown, attach the ground wire to the
indicated hole in the Handrail with a Silver Ground Screw
(94).
5
Ground
Wire
94
Hole
20
Console
Assembly
6. While a second person continues to hold the console as-
sembly, look underneath it and locate the Console Wire
Harness (78).
6
78
77
Console
Assembly
Connect the Console Wire Harness (78) to the Upright
Wire Harness (77). Make sure to connect the connec-
tors properly (see the inset drawing). The connectors
should slide together easily and snap into place. If the
connectors do not slide together easily and snap into
place, turn one connector and then try again. IF THE
CONNECTORS ARE NOT CONNECTED PROPERLY,
THE CONSOLE MAY BE DAMAGED WHEN THE
POWER IS TURNED ON. Then, insert the Wire
Harnesses down into the Handrail (20).
78
77
20
7. Set the console assembly on the Handrail (20). Be care-
ful to avoid pinching any of the wires. Hand tighten
five Screws (3) into the Handrail and the console assem-
bly. Do not put Screws into the two indicated holes.
Start all five Screws, but do not tighten them yet.
7
Console Assembly
20
3
3
3
No Screws
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Hand tighten four additional Screws (3) into the Handrail
(20) and the console assembly. Then, tighten all nine
Screws used in step 7 and this step; do not over-
tighten the Screws.
8
Console Assembly
20
3
3
3
9. Lower the Uprights (13, 14) until the Handrail (20) is
touching the floor.
9
13, 14
See the lower drawing. Position the Uprights (13, 14) so
the Frame (58) is centered between them.
20
See the upper drawing. Firmly tighten the four Upright
Bolts (65). Then, raise the Uprights (13, 14) back to the
vertical position.
65
Top View
14
10
13
58
10. Attach the Latch Housing (73) to the Left Upright (13)
with two Screws (3); start both Screws and then
tighten them. Make sure that the large hole in the
Latch Housing is on the indicated side.
13
3
73
Remove the knob from the pin. Make sure that the collar
and the spring are on the pin. (Note: If there are two col-
lars, place one on each side of the spring.) Next, insert
the pin into the Latch Housing (73). Then, tighten the
knob back onto the pin.
Knob
Spring
Collar
3
Large
Hole
Pin
Before operating the treadmill, plug in the power
cord (see page 11), and then lower the treadmill to
the lowest incline level (see page 13).
11. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread-
mill. Note: Extra hardware may be included. Keep the included allen wrench in a secure place; the large allen
wrench is used to adjust the walking belt (see page 23).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE CHEST PULSE SENSOR
HOW TO PUT ON THE CHEST PULSE SENSOR
dried. If the chest pulse sensor is not dried after
each use, it may remain activated longer than nec-
essary, draining the battery prematurely.
The chest pulse sensor consists of two components:
the chest strap and the sensor unit (see the drawing
below). Insert the tab on one end of the chest strap into
one end of the sensor unit, as shown in the inset draw-
ing. Press the end of the sensor unit under the buckle
on the chest strap. The tab should be flush with the
front of the sensor unit.
• Store the chest pulse sensor in a warm, dry place.
Do not store the chest pulse sensor in a plastic bag
or other container that may trap moisture.
• Do not expose the chest pulse sensor to direct
sunlight for extended periods of time; do not expose
it to temperatures above 122° Fahrenheit (50°
Celsius) or below 14° Fahrenheit (-10° Celsius).
• Do not excessively bend or stretch the sensor unit
when using or storing the chest pulse sensor.
Chest Strap
Tabs
• Clean the sensor unit using a damp cloth—never
use alcohol, abrasives, or chemicals. The chest
strap may be hand washed and air dried.
Tab
CHEST PULSE SENSOR TROUBLESHOOTING
Sensor
Unit
Buckle
Sensor Unit
The instructions on the following pages explain
how the chest pulse sensor is used with the con-
sole. If the chest pulse sensor does not function
properly, try the steps below.
Next, wrap the
chest pulse sen-
sor around your
chest and attach
the other end of
the chest strap to
the sensor unit.
Adjust the length
of the chest strap,
if necessary. The
chest pulse sen-
• Make sure that you are wearing the chest pulse sen-
sor as described at the left. Note: If the chest pulse
sensor does not function when positioned as de-
scribed, move it slightly lower or higher on your chest.
• Use saline solution such as saliva or contact lens
solution to wet the two electrode areas on the
sensor unit. If heart rate readings do not appear until
you begin perspiring, re-wet the electrode areas.
sor should be under your clothes, tight against your
skin, and as high under the pectoral muscles or
breasts as is comfortable. Make sure that the logo on
the sensor unit is facing forward and is right-side-up.
• As you walk or run on the treadmill, position your-
self near the center of the walking belt. For the
console to display heart rate readings, the user
must be within arm’s length of the console.
Pull the sensor unit away from your body a few inches
and locate the two electrode areas on the inner side
(the electrode areas are covered by shallow ridges).
Using saline solution such as saliva or contact lens so-
lution, wet both electrode areas. Return the sensor unit
to a position against your chest.
• The chest pulse sensor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical
conditions such as premature ventricular contrac-
tions (pvcs), tachycardia bursts, and arrhythmia.
CHEST PULSE SENSOR CARE AND MAINTENANCE
• The operation of the chest pulse sensor can be
affected by magnetic interference caused by high
power lines or other sources. If it is suspected that
this is a problem, try relocating the treadmill.
• Thoroughly dry the chest pulse sensor after each
use. The chest pulse sensor is activated when the
electrode areas are wetted and the heart rate
monitor is put on; the chest pulse sensor shuts off
when it is removed and the electrode areas are
• The CR2032 battery may need to be replaced (see
page 24).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local IMAGE dealer or call the toll-free tele-
phone number on the front cover of this manual
and order part number 146148, or see your local
electronics store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Note: If there is a sheet of clear plastic
on the face of the console, remove it.
Clip
Key
FEATURES OF THE CONSOLE
MyTracks™ StepCounter Program
Walking is one of the most popular exercises world-
wide. Walking does not require advanced conditioning
or special skills, yet it produces numerous benefits,
such as increased calorie burning, a slimmer waist,
toned muscles, enhanced energy and stamina, lower
blood pressure, and reduced stress.
The treadmill console offers a selection of features
designed to make your workouts more effective. When
the manual mode of the console is selected, the speed
and incline of the treadmill can be changed with the
touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the handgrip pulse sen-
sor or the chest pulse sensor.
To track your walking exercise, the console offers a
MyTracks™ StepCounter program that allows you to
enter the number of steps that you plan to walk, and
counts down the steps as you exercise.
Trainer Programs
The console also features six trainer programs. Each
trainer program automatically controls the speed and
incline of the treadmill as it guides you through an ef-
fective workout.
More reliable than conventional pedometers, the
MyTracks™ StepCounter is highly accurate with most
users. For the best results, try to maintain a consistent
pace, stride length, and position on the treadmill as
you walk. Lighter users may also find it helpful to re-
duce the incline of the treadmill or to increase the
speed of the walking belt.
Cardio Control Programs
The console also offers two cardio control programs.
Each cardio control program adjusts the speed and in-
cline of the treadmill to keep your heart rate near a tar-
get heart rate setting during your workouts.
To use the manual mode of the console, follow the
steps beginning on page 13. To use a trainer
program, see page 15. To use a cardio control pro-
gram, see page 16. To use the MyTracks™
StepCounter program, see page 18.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
walking belt as desired
by pressing the Speed
increase and decrease
buttons. Each time a
button is pressed, the
Plug in the power cord (see page 11).
1
speed setting will
Locate the reset/off
circuit breaker near
the power cord. Make
sure that the circuit
breaker is in the reset
position.
2
change by 0.1 mph; if a button is held down, the
speed setting will change in increments of 0.5
mph. Note: After the buttons are pressed, it may
take a moment for the walking belt to reach the se-
lected speed setting.
Reset
Position
If one of the numbered speed buttons is pressed,
the walking belt will gradually change in speed until
it reaches the selected speed setting.
Next, stand on the foot rails of the treadmill. Find
the clip attached to the key (see the drawing on
3
page 12) and slide the clip onto the waistband of
your clothes. Then, insert the key into the console.
After a moment, the display will light. Test the
clip by carefully taking a few steps backward
until the key is pulled from the console. If the
key is not pulled from the console, adjust the
position of the clip as needed.
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the numbered
speed buttons.
Note: The first time the treadmill is used, observe
the alignment of the walking belt, and center the
walking belt if necessary (see page 23).
HOW TO USE THE MANUAL MODE
Change the incline of the treadmill as desired.
4
5
Insert the key into the console.
To change the incline of
the treadmill, press the
Incline increase and de-
crease buttons. Each
time a button is pressed,
the incline will change by
0.5%. Note: After the buttons are pressed, it may
take a moment for the treadmill to reach the se-
lected incline setting.
1
See HOW TO TURN ON THE POWER above.
Select the manual mode.
2
When the
key is in-
serted, the
manual
mode will be
selected. If a
program has
Track
Follow your progress with the display.
When the
been selected, reselect the manual mode by
pressing the Program Select button repeatedly
until a track appears in the display.
manual mode
is selected,
the display
will show a
track that
represents
Track
Start the walking belt.
3
To start the walking belt, press the Start button,
the Speed increase button, or one of the speed
buttons numbered 1 to 10.
1/4 mile. As you walk or run, the indicators around
the track will appear in succession until the entire
track appears. The track will then disappear and
the indicators will again begin to appear in succes-
sion.
If the Start button or the Speed increase button is
pressed, the walking belt will begin to move at 1
mph. As you exercise, change the speed of the
13
Download from Www.Somanuals.com. All Manuals Search And Download.
The left side of the dis-
play will show the
elapsed time, the dis-
To measure your heart rate, stand on the foot
rails and hold the metal contacts on the
tance that you have
walked or run, and the
incline level of the tread-
mill. Note: When a program is selected (except for
cardio control program 8), the display will show
the time remaining in the program instead of the
elapsed time.
handrail—avoid moving your hands. When your
pulse is detected, the heart symbol in the right side
of the display will begin to flash each time your
heart beats, one or two dashes will appear, and
then your heart rate will be shown. For the most
accurate heart rate reading, continue to hold
the contacts for about 15 seconds.
The right side of the
display will show the
approximate number of
calories you have
burned, the speed of
the walking belt, and
your pace (in minutes per mile). The right side of
the display will also show your heart rate when you
use the handgrip pulse sensor or the chest pulse
sensor.
Turn on the fan if desired.
7
8
To turn on the fan, press the Fan button. To turn
on the fan at high speed, press the button a sec-
ond time. To turn off the fan, press the button a
third time. Note: If the fan is left on when the walk-
ing belt is stopped, the fan will automatically turn
off after a few minutes.
When you are finished exercising, remove the
key.
Note: The console can
display speed and dis-
tance in either miles or
kilometers. To find which
unit of measurement is
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage posi-
tion or the treadmill will be damaged. Next, re-
move the key from the console and put it in a se-
cure place. Note: If the display remains lit after
the key is removed, the console is in the
“demo” mode. See page 19 and turn off the
demo mode.
selected, hold down the
Stop button, insert the key into the console, and
then release the Stop button. An “E” for English
miles or an “M” for metric kilometers will appear
near the lower edge of the display. To change the
unit of measurement, press the Speed increase
button. When the desired unit of measurement is
selected, remove the key. Note: For simplicity,
all instructions in this section refer to miles.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
To reset the display, press the Stop button, re-
move the key, and then reinsert the key.
Measure your heart rate if desired.
6
Note: If you use the handgrip pulse sensor and
the chest pulse sensor at the same time, the con-
sole will not display your heart rate accurately.
Before using the handgrip pulse sensor, remove
the sheets of
clear plastic
from the
metal con-
tacts. In ad-
dition, make
sure that
Contacts
your hands
are clean.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
tings for the next several segments will be shown
in the columns to the right.
HOW TO USE A TRAINER PROGRAM
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. If the speed and/or in-
cline of the treadmill is about to change, the speed
setting and/or the incline setting will flash in the
display to alert you.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
13.
Select one of the trainer programs.
2
To select
When the first segment is completed, all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second seg-
ment. Note: If all of the indicators in the Current
Segment column are lit, the speed settings may
move downward so that only the highest indicators
appear in the matrix.
one of the
trainer pro-
grams,
press the
Trainer
Programs
button re-
peatedly
until “P 1,” “P 2,” “P 3,” “P 4,” “P 5,” or “P 6” ap-
pears in the display. When a trainer program is
selected, the program time will appear in the dis-
play, the maximum incline setting of the program
and the maximum speed setting of the program
will flash in the display for a few seconds, and a
profile of the speed settings of the program will
scroll across the matrix in the display.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
If the speed or incline setting for the current seg-
ment is too high or too low, you can manually
override the setting by pressing the Speed or
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will appear or dis-
appear in the Current Segment column; if any of
the columns to the right of the Current Segment
column have the same number of lit indicators as
the Current Segment column, an additional indica-
tor may appear or disappear in those columns as
well. Important: When the current segment of
the program ends, the treadmill will automati-
cally adjust to the speed and incline settings
for the next segment.
Press the Start button or the Speed increase
button to start the program.
3
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into 30 one-minute seg-
ments. One speed setting and one incline setting
are programmed for each segment. Note: The
same speed setting and/or incline setting may be
programmed for two or more consecutive seg-
ments.
To stop the program at any time, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Speed increase button. The walking belt will
begin to move at 1 mph. When the next segment
of the program begins, the treadmill will automati-
cally adjust to the speed and incline settings for the
next segment.
The speed
setting for
the first seg-
ment will be
shown in
the flashing
Current Segment
Current
Segment column of the matrix. (The incline set-
tings are not shown in the matrix.) The speed set-
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Follow your progress with the display.
See step 5 on page 13.
HOW TO USE A CARDIO CONTROL PROGRAM
4
5
6
7
Cardio control program 7 will automatically adjust the
speed and incline of the treadmill to keep your heart rate
within a preset range during your workout. Cardio control
program 8 will keep your heart rate near a target heart
rate setting that you select.
Measure your heart rate if desired.
See step 6 on page 14.
Turn on the fan if desired.
See step 7 on page 14.
CAUTION:
If you have heart prob-
lems, or if you are over 60 years of age and
have been inactive, do not use the cardio con-
trol programs. If you are taking medication reg-
ularly, consult your physician to find whether
the medication will affect your exercise heart
rate.
When you are finished exercising, remove the
key from the console.
See step 8 on page 14.
Follow the steps below to use a cardio control program.
Put on the chest pulse sensor.
1
See page 10.
Insert the key into the console.
2
See HOW TO TURN ON THE POWER on page
13.
Select a cardio control program.
3
To select a cardio control program, press the
Program Select button repeatedly until “P 7” or
“P 8” appears in the display.
If cardio
control pro-
gram 7 is
selected, a
profile of the
target heart
rate settings
of the pro-
gram will
scroll across the matrix in the display.
If cardio
control pro-
gram 8 is
selected, a
graphic rep-
resenting
your heart-
beat will ap-
pear in the
matrix.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
the Current Segment column and the column to
the right will flash and a series of tones will sound.
When the first segment ends, all target heart rate
settings will move one column to the left. The tar-
get heart rate setting for the second segment will
then be shown in the flashing Current Segment
column.
Enter a target heart rate setting.
4
If cardio control pro-
gram 7 is selected, the
maximum target heart
rate setting of the pro-
gram will appear in the
display. If desired, press
During both cardio control programs, the console
will regularly compare your heart rate to the cur-
rent target heart rate setting. If your heart rate is
too far below or above the target heart rate set-
ting, the speed of the walking belt will automati-
cally increase or decrease to bring your heart rate
closer to the target heart rate setting. If the speed
of the walking belt reaches 7.5 mph and your
heart rate is still too far below the target heart rate
setting, the incline of the treadmill will also in-
crease.
the increase and decrease buttons beside the
Program Select button to change the maximum
target heart rate setting (see EXERCISE INTEN-
SITY on page 25). Note: If the maximum target
heart rate setting is changed, the intensity level of
the entire program will change.
If cardio control pro-
gram 8 is selected, the
target heart rate setting
for the program will be
displayed. If desired,
press the increase and
If the speed or incline setting is too high or too low
at any time during the program, you can adjust the
setting with the Speed or Incline buttons. However,
each time the console compares your heart rate to
the target heart rate setting, the speed and/or in-
cline of the treadmill may automatically change to
bring your heart rate closer to the target heart rate
setting.
decrease buttons beside the Program Select but-
ton to change the target heart rate setting (see
EXERCISE INTENSITY on page 25). Note: The
same target heart rate setting will be programmed
for the entire program.
Press the Start button or the Speed increase
button to start the program.
5
If your pulse is not detected during the program,
the letters “PLS” will flash in the display and the
speed and/or incline of the treadmill may automat-
ically decrease. If this occurs, see page 10.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
To stop the program at any time, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Speed increase button. The walking belt will
begin to move at 1 mph. When the console com-
pares your heart rate to the target heart rate set-
ting, the speed and/or incline of the treadmill may
automatically change to bring your heart rate
closer to the target heart rate setting.
Cardio control program 7 is divided into 30 one-
minute segments. One target heart rate setting is
programmed for each segment. (Note: The same
target heart rate setting may be programmed for
two or more consecutive segments.) Cardio con-
trol program 8 is divided into 100 one-minute seg-
ments. The same target heart rate setting is pro-
grammed for all segments. Note: For a shorter
workout, simply stop the program before it ends.
Follow your progress with the display.
See step 5 on page 13.
If cardio
control pro-
gram 7 is
selected, the
target heart
6
7
8
Turn on the fan if desired.
See step 7 on page 14.
Current Segment
rate setting
for the first
segment will be shown in the flashing Current
Segment column of the matrix. The target heart
rate settings for the next several segments will be
shown in the columns to the right. When only
three seconds remain in the first segment, both
When you are finished exercising, remove the
key from the console.
See step 8 on page 14.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the Start button or the Speed increase
button to start the program.
HOW TO USE THE MYTRACKS™ STEP
COUNTER PROGRAM
3
A moment after the button is pressed, the walking
belt will begin to move at 2 mph. Hold the
handrails and begin walking.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
13.
As you exercise, adjust the speed and incline of
the treadmill as desired by pressing the Speed
and Incline buttons.
Select the 10,000 steps program.
2
During the program, the display will show the
number of steps still to be taken. When only ten
steps remain, the display will flash and a tone will
sound repeatedly until you reach the goal. The
walking belt will then slow to a stop.
Press the
10,000
Steps
Program
button; a
goal of
To stop the program temporarily, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Speed increase button. The walking belt will
begin to move at 2 mph.
10,000
steps will
appear in
the display.
Depending on your fitness level, you may desire
to walk fewer than or more than 10,000 steps. To
change the goal, press the increase and decrease
buttons beside the 10,000 Steps Program button.
Each time a button is pressed, the goal will change
by 500 steps. Note: The goal can be changed
either before or after the program is started.
Follow your progress with the display.
See step 5 on page 13.
4
5
6
7
Measure your heart rate if desired.
See step 6 on page 14.
Note: To find an appropriate starting goal, walk on
the treadmill with the manual mode selected (see
page 13), and note the number of steps that you
walk during your workout. Then, round that num-
ber up to the nearest 500 steps. This can be a
starting goal. As your fitness level improves, you
can increase the goal by 500 steps every few
weeks. IMPORTANT: Always exercise at an in-
tensity level and for a length of time that is
comfortable for you.
Turn on the workout fan if desired.
See step 7 on page 14.
When the program is completed, remove the
key from the console.
See step 8 on page 14.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE/DEMO MODE
total number of hours that the treadmill has been oper-
ated. In addition, an “E” for English miles or an “M” for
metric kilometers will appear in the lower part of the dis-
play. To change the unit of measurement, press the
Speed increase button.
The console features an information mode that keeps
track of treadmill usage information. The information
mode also allows you to select miles or kilometers as
the unit of measurement and to turn on and turn off the
demo mode.
IMPORTANT: If a “d” appears in the display, the con-
sole is in the “demo” mode. This mode is intended to be
used only when a treadmill is displayed in a store.
To select the information mode, hold down the Stop
button, insert the key into the console, and then release When the console is in the demo mode, the power cord
the Stop button. When the information mode is se-
lected, the following information will appear in the dis-
play:
can be plugged in, the key can be removed from the
console, and the indicators in the display will automati-
cally appear in a preset sequence, although the but-
tons on the console will not operate. If a “d” appears
when the information mode is selected, press the
Speed decrease button so “d” disappears.
The upper part of
the display will
show the number
of thousands of
steps taken by all
To exit the information mode, remove the key from the
console.
users of the
treadmill. The
center of the dis-
play will show the
total number of miles or kilometers that the walking belt
has moved. The lower part of the display will show the
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be per-
manently damaged. Next, unplug the power cord. CAUTION:
You must be able to safely lift 45 pounds (20 kg) to raise,
lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by the
arrow at the right. CAUTION: To decrease the possibility
of injury, do not lift the treadmill by the plastic foot rails.
Make sure you bend your legs and keep your back
straight. As you raise the treadmill, make sure to lift with
your legs rather than your back. Raise the treadmill about
halfway to the vertical position.
Frame
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the treadmill until the catch is
aligned with the latch pin. Slowly release the latch knob.
Make sure that the latch pin is fully inserted into the
catch.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sun-
light. Do not leave the treadmill in the storage position in
temperatures above 85° Fahrenheit.
Engaged
Catch
Latch Knob
Latch Pin
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the latch pin is
fully inserted into the catch.
1. Hold the upper ends of the handrails. Place one foot against
one of the wheels.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. To re-
duce the risk of injury, use extreme caution while mov-
ing the treadmill. Do not move the treadmill over an un-
even surface.
Base
Wheels
3. Place one foot against one of the wheels, and carefully lower
the treadmill until it is resting in the storage position.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand. Pull
the latch knob to the left and hold it. Pivot the treadmill down
until the catch is past the latch pin.
Open
Catch
Latch Knob
Latch Pin
2. Hold the metal frame firmly with both hands, and lower the
treadmill to the floor. CAUTION: To decrease the possibility
of injury, do not lower the treadmill by gripping only the
plastic foot rails. Do not drop the treadmill frame to the
floor. Be sure to bend your legs and keep your back
straight.
Frame
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call the toll-free telephone number on the
front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 11. Important: The treadmill is not com-
patible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
minutes, and then press the switch back in.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, see the front cover of this manual.
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-
move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The display of the console does not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
a
3
7
POWER CORD. With the help of a second person,
carefully tip the Uprights (13, 14) down as shown.
Next, remove the three Screws (3) and the three Hood
Screws (7). Note: A phillips screwdriver with a shaft at
least 5” long is required.
14
3
13
3
22
Download from Www.Somanuals.com. All Manuals Search And Download.
With the help of a second person, carefully raise the
Uprights (13, 14) to the position shown. Carefully pivot
the Hood (41) off.
41
13
14
Locate the Reed Switch (63) and the Magnet (46) on
the left side of the Pulley (47). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8”. If necessary, loosen the Screw
(3), move the Reed Switch slightly, and then retighten
the Screw. Reattach the Hood, and run the treadmill
for a few minutes to check for a correct speed reading.
Top
View
1/8”
46
47
3
63
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 11.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
2”–3”
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller bolts counterclockwise, 1/4 of a turn. When
the walking belt is properly tightened, you should be
able to lift each edge of the walking belt 2 to 3 inches
off the walking platform. Be careful to keep the walk-
ing belt centered. Then, plug in the power cord, insert
the key, and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, remove the key and
a
UNPLUG THE POWER CORD. If the walking belt
has shifted to the left, use the allen wrench to turn
the left rear roller bolt clockwise 1/2 of a turn; if the
walking belt has shifted to the right, turn the left
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Then, plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first re-
b
move the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn both rear roller bolts
clockwise, 1/4 of a turn. When the walking belt is cor-
rectly tightened, you should be able to lift each edge
of the walking belt 2 to 3 inches off the walking plat-
form. Be careful to keep the walking belt centered.
Then, plug in the power cord, insert the key, and care-
fully walk on the treadmill for a few minutes. Repeat
until the walking belt is properly tightened.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The chest pulse sensor does not function properly
SOLUTION: a. If the chest pulse sensor does not function properly, see CHEST PULSE SENSOR TROUBLE-
SHOOTING on page 10.
b. If the chest pulse sensor still does not function properly, the battery
b
should be changed. To replace the battery, locate the battery cover
on the back of the sensor unit. Insert a coin into the slot in the cover
and turn the cover counterclockwise to the “open” position. Remove
the cover.
Battery Cover
Remove the old battery from the sensor unit. Insert a new CR 2032
battery, making sure that the writing is on top. In addition, make sure
that the rubber gasket is in place in the sensor unit. Replace the bat-
tery cover and turn it to the closed position.
Battery
Cover
Battery
Rubber
Gasket
24
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
WORKOUT GUIDELINES
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your heart rate is in
your training zone for 20 to 60 minutes. (During the
first few weeks of your exercise program, do not keep
your heart rate in your training zone for longer than 20
minutes.) Breathe regularly and deeply as you exer-
cise—never hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-
exercise problems.
EXERCISE FREQUENCY
Fat Burning
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
1
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back foot
flat on the floor. Bend your front leg, lean forward and move your
hips toward the wall. Hold for 15 counts, then relax. Repeat 3 times
for each leg. To cause further stretching of the achilles tendons,
bend your back leg as well. Stretches: Calves, achilles tendons and
ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp one
foot with your other hand. Bring your heel as close to your buttocks
as possible. Hold for 15 counts, then relax. Repeat 3 times for each
leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
5
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. IMTL59105.0
R0805A
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
2
8
41
1
10
2
5
8
2
2
4
2
1
1
2
1
1
1
1
1
1
2
1
2
2
1
1
2
4
2
2
5
16
1
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
2
Foot Rail Cover
3/4” Screw
Screw
Catch
Foot Rail Screw
Isolator
Hood Screw
Star Washer
Platform Bolt, Back
Platform Bolt, Front
Belt Guide Screw
Belt Guide
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
#
1
1
1
1
1
1
1
1
1
1
4
4
5
4
2
1
4
1
3
1
4
1
1
1
1
1
2
2
6
12
1
1
1
4
1
4
2
1
1
2
1
1
1
4
4
1
1
1
1
1
1
Right Rear Endcap
Allen Wrench
Incline Stop Bracket
Ground Wire
Frame
Belly Pan
Reed Switch Bracket
Reed Switch Clip
Front Roller Nut
Reed Switch
Handrail Bolt
Upright Bolt
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
Left Upright
Star Washer
Right Upright
Frame Pivot Bolt
Left Foot Rail
Right Foot Rail
Motor Pivot Bolt
Motor Bracket
Handrail
Latch Pin Assembly
Motor Washer
Motor Star Washer
Motor Bolt
Motor Tension Bolt
Motor Belt
Drive Motor
Frame Washer
U-nut
Motor Nut
Lift Frame Bolt
Wheel Nut
1/2” Screw
Console
Fan Screw
Power Cord Assembly
Fan
Controller
Electronic Bracket
Filter Wire
Hood
Upright Star Washer
Caution Decal
Warning Decal
Platform Nut
Cable Tie
Cotter Pin
Latch Housing
Tie Clamp
Releasable Tie
Access Door
Wire Harness
Console Wire
Key/Clip
Front Wheel
Wheel Bolt
Base Pad
1” Tek Screw
Upright Base
Console Base
Incline Motor Bolt
Hair Pin Cotter Pin
Incline Motor
Handrail Star Washer
Rear Roller Bracket
Chest Pulse Sensor
Pulse Receiver
Pulse Receive Screw
Silver Ground Screw
Book Holder
Chest Pulse Strap
Wheel Spacer
Isolator Washer
Static Decal
6” Blue Wire, 2F
10” Red Wire, M/F
12” Green Wire, M/Ring
8” Black Wire, 2 Ring
User’s Manual
Front Roller Bushing
Lift Frame
Base Endcap
Front Roller Bolt
Magnet
Front Roller
Walking Belt
Walking Platform
Handrail Endcap
Rear Roller
Left Rear Endcap
Rear Roller Bolt
#
#
#
#
“#” indicates a non-illustrated part.
Specifications are subject to change without notice.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to give
the following information:
• the MODEL NUMBER of the product (IMTL59105.0)
• the NAME of the product (IMAGE 19.0 R treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the EXPLODED DRAWING in the center of this
manual and the PART LIST on page 27)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material under normal use and service conditions. The drive motor is warranted for ten (10) years after
the date of purchase. Parts and labor are warranted for ninety (90) days after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All re-
pairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customer’s responsibility. For in-
home service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, im-
proper or abnormal usage or repairs not provided by an ICON authorized service center; products used
for commercial or rental purposes; or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 226722 R0805A
Printed in USA © 2005 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|