Model No. IMTL39526
Serial No.
USER'S MANUAL
Serial
Number
Decal
QUESTIONS?
If you have questions, or if there
are missing or damaged parts,
we will guarantee complete sat-
isfaction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
Customer Hot Line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-800-753-4645
Mon.–Fri., 6 a.m.–6 p.m. MST
Patent Pending
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
12. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
13. Keep the power cord and the surge suppres-
sor away from heated surfaces.
protect the floor or carpet from damage, place 14. Never move the walking belt while the power
a mat under the treadmill.
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the tread-
mill is not working properly.)
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
7. The treadmill should not be used by persons
weighing more than 250 pounds.
17. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. Never leave the treadmill unattended while it
is running. Always remove the key, and un-
plug the power cord when the treadmill is not
in use.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 20.) You
must be able to safely lift 45 pounds (20 kg) to
raise, lower, or move the treadmill.
10. When connecting the power cord (see page 9),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
20. Do not change the incline of the treadmill by
placing objects under the treadmill.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 9. To purchase a surge suppressor, see
your local IMAGE dealer or call 1-800-753-4645
and order part number 146148.
21. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
22. When using iFIT.com CDs and videos, an
electronic “chirping” sound will alert you
when the speed of the treadmill is about to
change. Always listen for the “chirp” and be
prepared for speed changes. In some in-
stances, the speed may change before the
personal trainer describes the change.
treadmill regularly.
26. Never insert or drop any object into any
opening.
27.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
23. When using iFIT.com CDs and videos, you
can manually override the speed setting at
any time by pressing the speed buttons.
However, when the next “chirp” is heard, the
speed will change to the next settings for the
CD or video program.
24. Always remove iFIT.com CDs and videos from
your CD player or VCR when you are not
using them.
28. This treadmill is intended for in-home use
only. Do not use this treadmill in any commer-
cial, rental, or institutional setting.
25. Inspect and properly tighten all parts of the
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown have been placed on your treadmill. If a decal is missing, or if
it is not legible, please call our Customer Service Department, toll-free, to order
a free replacement decal (see the front cover of this manual). Apply the decal in
the location shown. Note: The decals are not all shown at actual size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the new IMAGE® 10.0 tread-
Department toll-free at 1-800-753-4645, Monday
mill. The 10.0 treadmill combines advanced technology through Friday, 6 a.m. until 6 p.m. Mountain Time (ex-
with innovative design to help you get the most from
your exercise program in the convenience of your
home. And when you’re not exercising, the unique 10.0
treadmill can be folded up, requiring less than half the
floor space of other treadmills.
cluding holidays). To help us assist you, please note
the product model number and serial number before
calling. The model number of the treadmill is
IMTL39526. The serial number can be found on a
decal attached to the treadmill (see the front cover of
this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
ing this manual, please call our Customer Service
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Book Holder
Console
Water Bottle Holder
(Bottle not included)
Thumb Pulse Sensor
Latch Knob
Handrail
Key/Clip
RIGHT SIDE
Reset/Off
Circuit Breaker
LEFT SIDE
Foot Rail
Walking Belt
Power Cord
Front Wheel
Cushioned Walking Platform
Rear Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires your own Phillips screw-
driver
pliers
, adjustable wrench
, wire cutters
, and needlenose
.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
To identify small parts during assembly, use the part identification drawings below.
Silver Screw
(107)–1
1 1/2” Screw (79)–4
3/4” Tek Screw
(101)–4
3/4” Screw (68)–2
4” Bolt (89)–4
Wheel Bolt (86)–2
3” Bolt (47)–4
Washer (29)–8
Wheel Nut (15)–2
1. Make sure that the power cord is not plugged in.
1
101
97
86
95
82
101
97
15
12
With the help of a second person, carefully tip the
treadmill onto its left side. Partially fold the Frame (12) so
the treadmill will be more stable; do not fully fold the
treadmill until it is completely assembled.
Attach two Base Pads (97) to the bottom of the Base (82)
with two 3/4” Tek Screws (101). Attach a Wheel (95) to
the outside of the Base with a Wheel Bolt (86) and a
Wheel Nut (15).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Identify the Right Upright (10), which has a large rectan-
gular hole near the upper end (see drawing 2b). Have a
second person hold the Right Upright near the Wire
Harness (17). Feed the end of the Wire Harness into the
Right Upright and out of the rectangular hole near the
upper end as shown. If necessary, use needlenose pliers
to pull the Wire Harness out of the hole.
2a
10
17
See drawing 2b. Locate the Left Upright (9). If the Latch
Housing (77) is not attached to the Left Upright, remove
the two Screws (76) from the Left Upright. Attach the
Latch Housing as shown with the two Screws. Firmly
tighten—but do not overtighten—the Screws.
2b
9
10
17
77
76
Rectangular
Hole
Large
Hole
3. Make sure that the Right Upright (10) is turned so it
bends in the direction shown. Insert two 3” Bolts (47) with
Washers (29) through the Base (82), and hand tighten
the Bolts into the lower end of the Right Upright.
3
82
47
29
10
With the help of a second person, tip the treadmill
onto its other side and repeat steps 1 through 3.
Note: There is not a wire harness in the Left Upright (not
shown). One extra Base Pad my be included.
Bend
4. With the help of a second person, set the treadmill flat on
the floor so the Right Upright (10) and the Left Upright
(not shown) are vertical.
4
107
Hold one of the Handrails (85) near the Right Upright
(10). Feed the end of the Wire Harness (17) into the bottom
of the Handrail and out of the indicated hole. Using the
Silver Screw (107), attach the end of the ground wire to
the small hole in the side of the Handrail.
Ground
Wire
17
Hole
85
5. Have a second person hold the Console Base (87) and
the Handrail (85) in the position shown. Touch the Right
Upright (10) to discharge any static. Insert the Wire
Harness (17) through the two Plastic Ties (108) on the
Console Base. Find the 3-wire connector on the end of
the Wire Harness, and insert the connector into the red
socket beneath the Console Base. The connector
should slide easily into the socket and snap into
place. If the connector does not slide easily and snap
into place, turn the connector and then insert it. If the
connectors are not inserted properly, the Console
may be damaged when the power is turned on.
10
5
87
85
108
17
5-wire
3-wire
Insert the 5-wire connector into the black socket beneath
the Console Base (87) in the same way. Make sure that the
connectors and wires appear as shown in the inset draw-
ing. Insert the excess Wire Harness (17) down through the
Handrail (85). Securely tighten the Plastic Ties (108) to
prevent the Wire Harness from slipping. Then, cut off
the ends of the Plastic Ties.
10
17
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Attach the Handrail (85) to the Console Base (87) with
two 1 1/2” Screws (79) as shown. Attach the other
Handrail (not shown) to the other side of the Console
Base in the same way.
6
87
79
17
85
Insert the excess Wire Harness (17) down into the Right
Upright (10) as you set the right Handrail (85) on the Right
Upright. Hand tighten two 4” Bolts (89) with Washers (29)
through the Right Upright into the right Handrail. Be careful
not to pinch the Wire Harness. Do not tighten the Bolts
yet.
29
89
10
Attach the left Handrail (not shown) to the Left Upright
(not shown) in the same way. Note: There is not a wire
harness in the Left Upright.
7. Hold the Connector Cover (110) on the Console Base
(87) in the position shown. Attach the Connector Cover
with two 3/4” Screws (68).
7
110
68
87
8. Remove the Latch Knob (105) from the Latch Pin (11).
Make sure that the Latch Pin Collar (14) and the Spring
(56) are on the Latch Pin as shown. Insert the Latch Pin
into the Storage Latch (77) and tighten the Latch Knob
onto the Latch Pin.
8
85
56
105
14
77
11
9
9. Lower the Uprights (9, 10) until the Handrails (not shown)
touch the floor. Make sure that the treadmill Frame (12)
is centered between the Uprights. See step 3. Firmly
tighten the four 3” Bolts (47). See step 6. Firmly tighten
the four 4” Bolts (89). Raise the Uprights back to the ver-
tical position.
9
Top View
87
Make sure that the two Cup Holders (118) are pressed
into the round holes in the top of the Console Base (87).
118
12
9
10
10.Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included allen wrench in a secure place; the allen wrench is used to adjust the walking
belt (see page 23). To protect the floor or carpet from damage, place a mat under the treadmill.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
TM
THE PERFORMANT LUBE WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appli-
ances being turned on or off. To decrease the possi-
bility of your treadmill being damaged, always use
a surge suppressor with your treadmill (see draw-
ing 1 at the right). To purchase a surge suppres-
sor, see your local IMAGE dealer or call 1-800-753-
4645 and order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indi-
cate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Note: If there is a thin sheet of
plastic on the console, remove it.
Clip
Key
speed of the treadmill as it guides you through an
effective workout.
CAUTION:
Before operating the
console, read the following precautions.
The console also features new iFIT.com interactive
technology. Having iFIT.com technology is like having a
personal trainer in your home. Using the included audio
cable, you can connect the treadmill to your home
stereo, portable stereo, computer, or VCR and play
special iFIT.com CD and video programs (iFIT.com
CDs and videocassettes are available separately).
iFIT.com CD and video programs automatically control
the speed and incline of the treadmill as a personal
trainer guides you through every step of your workout.
High-energy music provides added motivation. To pur-
chase iFIT.com CDs or videocassettes, call toll-
free 1-800-753-4645.
• Do not stand on the walking belt when turn-
ing on the power.
• Always wear the clip (see the drawing
above) while operating the treadmill.
• Adjust the speed in small increments to
avoid sudden jumps in speed.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed
water bottle in the water bottle holder.
With the treadmill connected to your computer, you
cess programs directly from the internet. Additional op-
tions are soon to be available. See www.iFIT.com for
more information.
FEATURES OF THE CONSOLE
The console offers a selection of features designed to
help you get the most from your exercise. When the
manual mode of the console is selected, the speed
and incline of the treadmill can be changed with a touch
of a button. As you exercise, the console will display
continuous exercise feedback. You can even measure
your heart rate using the built-in pulse sensor.
To use the manual mode of the console, follow the
steps beginning on page 11. To use a personal trainer
speed program, see page 12.To use an iFIT.com CD
or video program, see page 17. To use an iFIT.com
program directly from our Web site, see page 18.
Four certified personal trainer speed programs are
also offered. Each program automatically controls the
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
Each time a button is pressed, the speed setting
will change by 0.1 mph; if a button is held down,
the speed setting will change in increments of 0.5
mph. Note: The console can display speed and
distance in either miles or kilometers (see
SPEED DISPLAY on page 12). For simplicity, all
instructions in this section refer to miles.
Plug in the power cord (see page 9).
1
Stand on the foot rails of the treadmill.
2
To stop the walking belt, press the Stop button.
The Time display will begin to flash. To restart the
Find the clip attached to the key (see the drawing
on page 10), and slide the clip onto the waistband
3
walking belt, press the Start button or the Speed
button.
LL
of your clothes. Next, insert the key into the con-
sole. After a moment, the displays and various in-
dicators will light. Test the clip by carefully tak-
ing a few steps backward until the key is
pulled from the console. If the key is not
pulled from the console, adjust the position of
the clip.
Note: The first time you use the treadmill, periodi-
cally inspect the alignment of the walking belt, and
align it if necessary (see page 23).
Change the incline of the treadmill as desired.
4
5
To change the incline of the treadmill, press either
of the Incline buttons until the desired incline level
is reached.
HOW TO USE THE MANUAL MODE
Follow your progress with the LED track and
the displays.
Insert the key fully into the console.
1
The LED Track—When
the manual mode or the
iFIT.com mode is se-
lected, the LED display
will show a track repre-
senting 1/4 mile. As you
exercise, the indicators
around the track will light in sequence until you
have completed 1/4 mile. A new lap will then
begin.
See HOW TO TURN ON THE POWER above.
Select the manual mode.
2
When the key is in-
serted, the manual
mode will be selected
and the Manual Control
indicator will light. If a
program has been
selected, press the Mode button repeatedly to res-
elect the manual mode.
Calories/Fat Calories/
Pulse display—This dis-
play shows the approxi-
mate numbers of calories
and fat calories you have
Press the Start button or the Speed
start the walking belt.
L
button to
3
burned (see FAT BURN-
A moment after the but-
ton is pressed, the
walking belt will begin to
move. Hold the
handrails and begin
walking. As you exer-
cise, change the speed of the walking belt as de-
sired by pressing the Speed buttons.
ING on page 24). The display will change from
one number to the other every few seconds. The
FAT indicator will light when the number of fat
calories is shown. The display will also show your
heart rate when you use the pulse sensor (see
step 6 on page 12).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Time display—When
the manual mode or the
iFIT.com mode is se-
lected, this display will
show the elapsed time.
When a personal trainer
If the displayed heart rate appears to be too high
or too low, or if your heart rate is not displayed, lift
your thumb off the pulse sensor for a few seconds.
Then, place your thumb on the pulse sensor as de-
scribed above. Remember to stand still while mea-
suring your heart rate.
program is selected, the display will show the time
remaining in the program.
When you are finished exercising, remove the
key.
7
Distance display—This
display shows the dis-
tance that you have
walked or run.
Step onto the foot rails and press the Stop button.
Adjust the incline of the treadmill to the lowest
setting. Next, remove the key from the console and
put it in a secure place.
Speed display—This
display shows the speed
of the walking belt.
HOW TO USE PERSONAL TRAINER PROGRAMS
Insert the key fully into the console.
1
See HOW TO TURN ON THE POWER on page
11.
Note: The console can
display speed and dis-
tance in either miles or
kilometers. To see which
unit of measurement is
selected, hold down the
Stop button, insert the key into the console, and
continue to hold the Stop button for a few seconds.
An “E” for English miles or an “M” for metric kilo-
meters will appear in the display. Press the Speed
Select a personal trainer program.
2
When the key is in-
serted, the manual
mode will be selected.
To select a personal
trainer program, press
the Mode button repeat-
edly until one of the four
personal trainer program indicators lights. When a
personal trainer program is selected, the Time dis-
play will show how long the program will last and
the Speed display will flash the maximum speed
setting for the program for a few seconds.
L
button to change the unit of measurement.
When the desired unit of measurement is selected,
remove the key and then reinsert it.
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
Measure your heart rate, if desired.
6
The profiles in the cen-
ter of the console show
how the speed of the
treadmill will change
during the programs.
The first four speed set-
tings for the selected
program will be shown in the LED display.
To measure
your heart rate,
stand on the
foot rails and
place your
Pulse Sensor
thumb on the
pulse sensor.
Do not press
too hard, or the
circulation in your thumb will be restricted and
your pulse will not be detected. After a few sec-
onds, the PULSE indicator beside the Calories/ Fat
Calories/Pulse display will light and then your heart
rate will be shown. Hold your thumb on the pulse
sensor for about 15 seconds for the most accurate
reading.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
The program will continue until the speed setting
for the last period is shown in the Current Period
column and no time remains in the Time display.
The walking belt will then slow to a stop.
Press the Start button or the Speed
start the program.
L
button to
3
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed set-
ting for the program. Hold the handrails and begin
walking.
Note: If the speed setting for the current period is
too high or too low, you can manually override the
setting by pressing the Speed buttons. Every few
times a button is pressed, an additional indicator
will light or darken in the Current Period column. (If
any of the columns to the right of the Current
Period column have the same number of lit indica-
tors as the Current Period column, an additional
indicator may light or darken in those columns as
well.) Important: When the current period of the
program ends, the treadmill will automatically
adjust to the speed setting for the next period.
Each program is divided into several time periods
of different lengths. One speed setting is pro-
grammed for each period. (The same speed set-
ting may be programmed for consecutive periods.)
The speed setting for
the first period will be
shown in the flashing
Current Period column
of the LED display. The
speed settings for the
next four periods will be
shown in the four
Current Period
To stop the program temporarily, press the Stop
button. The Time display will begin to flash. To
restart the program, press the Start button or the
columns to the right.
Speed
L
button. To end the program, press the
When only three seconds remain in the first period
of the program, the Speed display will flash, the
Current Period column and the column to the right
will flash, and a series of tones will sound. When
the first period is completed, all speed settings will
move one column to the left. The speed setting for
the second period will then be shown in the flash-
ing Current Period column and the treadmill will
automatically adjust to the speed setting for the
second period. (When the same speed setting is
programmed for consecutive periods, the Speed
display will not flash and the column to the right of
the Current Period column will not flash during the
last three seconds of the current period.)
Stop button, remove the key, and then reinsert the
key.
Follow your progress with the displays.
See step 5 on page 11.
4
5
6
Measure your heart rate, if desired.
See step 6 on page 12.
When the program is completed, remove the
key from the console.
When the program has ended, adjust the incline
of the treadmill to the lowest setting. Next, re-
move the key from the console and put it in a safe
place.
Note: If all of the indicators in the Current Period
column are lit after the speed settings have moved
to the left, the speed settings will move downward
so only the highest indicators in the columns ap-
pear in the LED display. If some indicators in the
Current Period column are not lit after the speed
settings have moved to the left again, the speed
settings will move back up.
To change the incline of the treadmill during the
program, press the Incline buttons until the de-
sired incline level is reached.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE TREADMILL TO YOUR
CD PLAYER, VCR, OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com CDs, the treadmill must be connected
to your portable CD player, portable stereo, home
stereo, or computer with CD player. See pages 14 and
15 for connecting instructions. To use iFIT.com video-
cassettes, the treadmill must be connected to your
VCR. See page 16 for connecting instructions. To use
iFIT.com programs directly from our internet site,
the treadmill must be connected to your home com-
puter. See page 15 for connecting instructions.
A. Plug one end of the audio cable into the jack beneath
the console. Plug the other end of the cable into the
included adapter. Plug the adapter into an AUDIO
OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
LEFT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
Adapter
Audio
Cable
A. Plug one end of the audio cable into the jack be-
neath the console. Plug the other end of the cable
into the LINE OUT jack on your CD player. Plug
your headphones into the PHONES jack.
B. Plug one end of the audio cable into the jack be-
neath the console. Plug the other end of the cable
into the LINE OUT jack on your stereo.
A
PHONES LINE OUT
LINE OUT
PHONES
B
Head-
phones
LINE OUT
Audio
Cable
Audio
Cable
B. Plug one end of the audio cable into the jack be-
neath the console. Plug the other end of the cable
into a 3.5mm Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your CD player. Plug your headphones into the
other side of the Y-adapter.
C. Plug one end of the audio cable into the jack be-
neath the console. Plug the other end of the cable
into a 3.5mm Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your stereo. Plug your headphones into the other
side of the Y-adapter.
B
PHONES
PHONES
C
3.5mm
Y-adapter
PHONES
Audio
Cable
3.5mm
Y-adapter
Audio
Cable
Headphones
Headphones
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack be-
neath the console. Plug the other end of the cable
into the included adapter. Plug the adapter into the
LINE OUT jack on your stereo.
A. Plug one end of the audio cable into the jack be-
neath the console. Plug the other end of the cable
into the LINE OUT jack on your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Adapter
Audio
Cable
B. Plug one end of the audio cable into the jack be-
neath the console. Plug the other end of the cable
into a 3.5mm Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your computer. Plug your headphones or speak-
ers into the other side of the Y-adapter.
B. Plug one end of the audio cable into the jack be-
neath the console. Plug the other end of the cable
into the included adapter. Plug the adapter into an
RCA Y-adapter (available at electronics stores).
Next, remove the wire that is currently plugged into
the LINE OUT jack on your stereo and plug the wire
into the unused side of the Y-adapter. Plug the Y-
adapter into the LINE OUT jack on your stereo.
B
PHONES
B
CD
Audio
Cable
3.5mm
Y-adapter
VCR
Amp
LINE OUT
Headphones/Speakers
RCA
Y-adapter
Audio
Cable
Adapter
Wire removed from
LINE OUT jack
15
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR VCR
B. Plug one end of the audio cable into the jack be-
neath the console. Plug the other end of the cable
into the included adapter. Plug the adapter into an
RCA Y-adapter (available at electronics stores).
Next, remove the wire that is currently plugged into
the AUDIO OUT jack on your VCR and plug the
wire into the unused side of the Y-adapter. Plug the
Y-adapter into the AUDIO OUT jack on your VCR.
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 15.
A. Plug one end of the audio cable into the jack be-
neath the console. Plug the other end of the cable
into the included adapter. Plug the adapter into the
AUDIO OUT jack on your VCR.
B
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
A
ANT
.
IN
RCA Y-adapter
Audio
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
AUDIO OUT
Adapter
Cable
RIGHT
LEFT
Adapter
Wire removed from
AUDIO OUT jack
Audio
Cable
16
Download from Www.Somanuals.com. All Manuals Search And Download.
If the speed setting is too high or too low, you can
manually override the setting at any time by
pressing the Speed buttons on the console.
However, when the next “chirp” is heard, the
speed will change to the next setting of the CD
or video program.
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
To use iFIT.com CDs or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on page
14. Note: IFIT.com CD and video programs will con-
trol only the speed of your treadmill.
To stop the walking belt at any time, press the
Stop button on the console. The Time display will
begin to flash. To restart the program, press the
Start button or the Speed
L
button. After a mo-
ment, the walking belt will begin to move. When
the next “chirp” is heard, the speed will
change to the next setting of the CD or video
program.
To purchase iFIT.com CDs or videocassettes, call
toll-free 1-800-753-4645.
Follow the steps below to use an iFIT.com CD or video
program.
When the CD or video program is completed, the
walking belt will stop and the Time display will
begin to flash. Note: To use another CD or video
program, press the Stop button or remove the key
and go to step 1.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 11.
Note: If the speed of the treadmill does not
change when a “chirp” is heard:
Select the iFIT.com mode.
2
• Make sure that the iFIT.com indicator is lit and
that the Time display is not flashing. If the
Time display is flashing, press the Start but-
When the key is in-
serted, the manual
mode will be selected.
To use iFIT.com CDs
ton or the Speed
L
button on the console.
or videocassettes,
press the Mode button
repeatedly until the iFIT.com indicator lights.
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the con-
sole may not detect the program signals.
Insert the iFIT.com CD or videocassette.
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
3
If you are using an iFIT.com CD, insert the CD
into your CD player. If you are using an iFIT.com
videocassette, insert the videocassette into your
VCR.
Follow your progress with the LED track and
the displays.
5
Press the PLAY button on your CD player or
VCR.
See step 5 on page 11.
4
Measure your heart rate, if desired.
See step 6 on page 12.
A moment after the button is pressed, your per-
sonal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions. Note: If the Time display is flashing,
6
7
When the program is completed, remove the
key.
press the Start button or the Speed
L
button on
the console. The treadmill will not respond to a
CD or video program when the Time display is
flashing.
See step 6 on page 13.
CAUTION: Always remove iFIT.com CDs and
videocassettes from your CD player or VCR
when you are finished using them.
During the CD or video program, an electronic
“chirping” sound will alert you when the speed of
the treadmill is about to change. CAUTION:
Always listen for the “chirp” and be prepared
for speed changes. In some instances, the
speed may change before the personal trainer
describes the change.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
7
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed of
the treadmill is about to change. CAUTION:
Always listen for the “chirp” and be prepared
for speed changes.
for details. Note: Programs will control only the
speed of your treadmill.
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 15. In
addition, you must have an internet connection and
an internet service provider. A list of specific system re-
quirements will be found on our Web site.
If the speed setting is too high or too low, you can
manually override the setting at any time by press-
ing the Speed buttons on the console. However,
when the next “chirp” is heard, the speed will
change to the next setting for the program.
Follow the steps below to use a program from our
Web site.
To stop the walking belt at any time, press the
Stop button on the console. The Time display will
begin to flash. To restart the program, press the
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 11.
Start button or the Speed
L
button. After a mo-
ment, the walking belt will begin to move. When
the next “chirp” is heard, the speed will change
to the next setting for the program.
Select the iFIT.com mode.
2
When the key is in-
serted, the manual
When the program is completed, the walking belt
will stop and the Time display will begin to flash.
Note: To use another program, press the Stop
button and go to step 5.
mode will be selected.
To use a program from
our Web site, press the
Mode button repeatedly
until the iFIT.com indicator lights.
Note: If the speed of the treadmill does not
change when a “chirp” is heard, make sure that
the iFIT.com indicator is lit and that the Time
display is not flashing. In addition, make sure
that the audio cable is properly connected, that
it is fully plugged in, and that it is not wrapped
around a power cord.
Go to your computer and start an internet
connection.
3
Start your web browser, if necessary, and go to
4
Follow the desired links on our Web site to se-
lect a program.
Follow your progress with the LED track and
the displays.
5
8
Read and follow the on-line instructions for using a
program.
See step 5 on page 11.
Measure your heart rate, if desired.
See step 6 on page 12.
Follow the on-line instructions to start the
program.
9
6
When you start the program, an on-screen count-
down will begin.
When the program is completed, remove the
key.
10
See step 6 on page 13.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE
The Distance/Laps display will
show the total number of miles
(or kilometers) that the walking
belt has moved.
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also al-
lows you to switch the console from miles per hour to
kilometers per hour.
An “E” for english miles or an
“M” for metric kilometers will
appear in the Speed display.
To select the information mode, hold down the Stop
button, insert the key into the console, and continue to
hold the Stop button for a few seconds. When the infor-
mation mode is selected, the following information will
be shown:
Press the Speed
change the unit of measure-
ment.
L
button to
To exit the information mode, remove the key from the
console.
The Time display will show the
total number of hours the
treadmill has been used.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. CAUTION: To decrease the possibility of
injury, bend your legs and keep your back straight. As
you raise the treadmill, make sure to lift with your legs
rather than your back. Raise the treadmill about halfway
to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the treadmill until the catch is
past the pin on the latch knob. Slowly release the latch
knob. Make sure that the catch is securely held by the
pin.
Open
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° Fahrenheit.
Latch
Knob
Closed
Pin
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the catch
is securely held by the pin on the latch knob.
1. Hold the handrails as shown and place one foot against a
wheel.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location.
Never move the treadmill without tipping it back. To
reduce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
3. Place one foot on a wheel, and carefully lower the tread-
mill until it is resting in the storage position.
Base
Wheels
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left hand, pull the latch knob to the
left and hold it. Pivot the treadmill down until the frame is
past the pin. Slowly release the latch knob.
Latch
Knob
Open
Pin
Catch
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. Do not drop the treadmill frame
to the floor. CAUTION: To decrease the possibility of
injury, bend your legs and keep your back straight.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-
free at 1-800-753-4645, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 9. Important: The treadmill is not compatible
with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill near the power cord. If the switch protrudes
as shown, the circuit breaker has tripped. To reset
the circuit breaker, wait for five minutes and then
press the switch back in.
Off
Reset
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker located on the treadmill frame near the power cord (see c.
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call our toll-free Customer Service Department.
PROBLEM: The speed display on the console does not function properly
SOLUTION: a. Remove the key and UNPLUG THE POWER CORD.
a
Remove the hood from the treadmill. Locate the Reed
1/8”
Switch (21) and the Magnet (43) on the left side of the
Pulley (42). Turn the Pulley until the Magnet is aligned
with the Reed Switch. Make sure that the gap be-
tween the Magnet and the Reed Switch is about
1/8”. If necessary, loosen the 3/4” Screw (76) and
move the Reed Switch slightly. Retighten the Screw.
Re-attach the hood, and run the treadmill for a few
minutes to check for a correct speed reading.
42
43
76
21
Top
View
22
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 9.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
3”–4”
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 3 to
4 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, in-
sert the key, and run the treadmill for a few minutes.
Rear Roller Adjustment Bolts
Repeat until the walking belt is properly tightened.
c. If the walking belt still slows when walked on, please
call our toll-free Customer Service Department.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
a
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right, turn the
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove
b
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise,
1/4 of a turn. When the walking belt is correctly tight-
ened, you should be able to lift each side of the walk-
ing belt 3 to 4 inches off the walking platform. Be
careful to keep the walking belt centered. Plug in the
power cord, insert the key, and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
WORKOUT GUIDELINES
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
EXERCISE FREQUENCY
To measure your heart rate during exercise, use the
pulse sensor.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
24
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
1
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot to-
ward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back and groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles ten-
dons, bend your back leg as well. Stretches: Calves, achilles ten-
dons and ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your but-
tocks as possible. Hold for 15 counts, then relax. Repeat 3 times
for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
5
25
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. IMTL39526
R0304A
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key
Key
Key
No. Qty. Description
No. Qty. Description
No. Qty. Description
1
2
3
1
1
4
1
Motor Belt
Pulley/Flywheel/Fan
Motor Nut
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
4
2
4
4
1
2
1
1
8
3
4
1
1
1
4
2
1
1
20
1
1
2
1
1
14
2
1
1
5
1
1
2
6
1
1
4
2
4
1
2
2
Platform Screw
Isolator
Isolator Fastener
3” Bolts
Incline Warning Decal
Belt Guide
Battery Cover
Front Belly Pan
U-nut
Cable Tie Clamp
Cable Tie
Walking Belt
Spring
Rear Roller
Hood Screw
Rear Foot
89
90
91
92
93
94
95
96
97
4
1
1
2
1
1
2
1
4
1
1
1
5
2
1
4
1
1
1
1
2
1
1
2
1
2
2
2
2
2
1
1
1
1
1
1
1
1
1
4” Bolt
Key/Clip
Incline Motor Belly Pan
Roller Adj. Washer
Book Holder
Motor Hood
Front Wheel
Incline Motor Shield
Base Pad
iFIT Wire
Upright Grommet
Allen Wrench
3/4” Tek Screw
Handrail Endcap
Power Board Plate
Base Cap
Latch Knob
Choke
Silver Screw
Warning Decal
Lift Spacer
Connector Cover
Hood Spacer
Bumper
Edge Guard
Upright Endcap
Metal Plate
Belly Pan Interface
Rear Foot Spacer
Cup Holder
Power Board Bracket
Controller Wire
Pulse Plate Cover
8” Blue Wire, 2F
4” Blue Wire, 2F
8” White Wire, 2F
4” White Wire, M/F
8” Green Wire, 2 Ring
User's Manual
4*
Motor/Pulley/
Flywheel/ Fan
Incline Motor Bolt
Incline Motor Spacer
Incline Motor
Stop Bracket
Left Upright
Right Upright
Latch Pin
Frame
Pin Clip
5
6
7
8
9
10
11
12
13
14
15
1
2
1
1
1
1
1
1
1
1
6
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
#
Latch Pin Collar
Wheel Nut/
Incline Motor Nut
Belt Guide Screw
Wire Harness
Hood Bracket
Front Hood Bracket
Warning Decal
Reed Switch
Reed Switch Clip
Power Board
Controller
Electronics Bracket
Reset/Off Circuit
Breaker
Power Cord
Power Cord Grommet
Washer
Latch Assembly
Incline Frame
Frame Pivot Bolt
Frame Pivot Spacer
Tension Bushing
Front Roller Adj. Bolt
Foot Rail Cap (Right)
Motor Tension Nut
Motor Bolt
Plastic Standoff
Foot Rail Cap (Left)
Left Foot Rail
Front Roller/Pulley
Magnet
iFIT Jack
Ground Wire
Screw
16
17
18
19
20
21
22
23
24
25
26
4
1
2
1
2
1
1
1
1
1
1
Left Rear Endcap
Right Rear Endcap
Rear Roller Adj. Bolt
Motor
Latch Decal
Console Screw
Catch Screw
Catch
Walking Platform
8” Cable Tie
Incline Bolt
Motor Tension Bolt
Right Foot Rail
3/4” Screw
Storage Latch Bracket
Console
1 1/2” Screw
Incline Pivot Nut
Motor Star Washer
Base
Incline Frame Bolt
Motor Tension
Washer
27
28
29
30*
31
32
33
34
35
36
37
38
39
40
41
42
43
1
1
10
1
1
2
2
1
1
1
1
4
4
1
1
1
1
#
#
#
#
#
#
* Includes all parts shown in the
box.
# These parts are not illustrated.
Specifications are subject to
change without notice.
85
86
87
88
2
2
1
1
Handrail
Wheel Bolt
Console Base
Console Crossbar
27
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. IMTL39526
R0304A
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. IMTL39526
R0304A
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-753-4645, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give
the following information:
• The MODEL NUMBER OF THE PRODUCT (IMTL39526)
• The NAME OF THE PRODUCT (IMAGE® 10.0 treadmill)
• The SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual)
• The KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the EXPLODED DRAWING in the center of
this manual and the PART LIST on page 27)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, mis-
use, improper or abnormal usage or repairs not provided by an ICON authorized service center; prod-
ucts used for commercial or rental purposes; or products used as store display models. No other war-
ranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 211626 R0304A
Printed in Canada © 2004 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|