®
Model No. 831.100430
Serial No.
Write the serial number in the space
above for reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or find that there
are missing or damaged parts,
we will guarantee complete satis-
faction through direct assistance
from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
Patent Pending
1-888-936-4266
Mon.–Thu., 8:00 am—6:30 pm;
Fri., 8:00 am—6:00 pm EST
CAUTION
USER’S MANUAL
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
SEARS CANADA, INC., TORONTO, ONTARIO M5B 2B8
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of drowning, electric shock, or serious injury, read the following
important precautions before using the RENEW 900.
READ AND FOLLOW ALL INSTRUCTIONS
1. It is the responsibility of the owner to ensure
that all users of the RENEW 900 are ade-
quately informed of all precautions.
13. Keep all chemicals away from children and
pets.
14. The pH and chemical balance of the water
must be maintained as explained in this man-
ual (see page 13). Failure to do so may cause
injury to users or damage to the spa jet unit,
and will void the warranty.
2. Use the RENEW 900 only as described in this
manual.
3. The RENEW 900 is intended for home use
only. Do not use the RENEW 900 in any com-
mercial, rental, or institutional setting.
15. The water pump in the spa jet unit must be
primed before you use the RENEW 900 the
first time. You must also prime the pump
before using the unit each time you re-fill the
spa. The spa jet unit may be seriously dam-
aged if the pump is not properly primed (see
PRIMING THE SPA JET UNIT on page 10).
4. Use the RENEW 900 only on a level surface.
Do not use the RENEW 900 on carpet or
other materials that could be damaged by
moisture. Do not use the RENEW 900 on
rough or sharp surfaces such as gravel or
wood chips.
16. DANGER—When connecting the power cord
(see PLUGGING IN THE RENEW 900 on page
10), plug the power cord directly into a
grounded circuit capable of carrying 15 or
more amps. No other appliance should be on
the same circuit. Replace the power cord
immediately if damaged.
5. The RENEW 900 will weigh approximately
2400 pounds when it is assembled and filled
with water. Be sure that the location you
select for the RENEW 900 will support this
weight, plus the weight of the occupants.
6. Inspect and tighten all parts regularly.
Replace any worn parts immediately.
17. Do not use an extension cord with the
RENEW 900. This could damage the motor
and will void the warranty.
7. DANGER—Risk of injury: Do not remove or
alter the covers on the suction fittings. Never
operate the RENEW 900 if the suction guard
is missing or broken. Keep hair and body
away from the suction guard. If you need to
replace a suction fitting, be sure that the flow
rate of the replacement is compatible.
18. DANGER—If you will be using the RENEW
900 outside, do not bury the power cord; you
should also keep the power cord away from
lawn mowers, hedge trimmers, and other
similar equipment.
8. Do not bring any object into the RENEW 900
that could puncture the liner.
19. WARNING—The power cord is equipped with
a Ground Fault Circuit Interrupter (GFCI),
located at the end of the power cord. The
GFCI must be tested before each use. To test
the GFCI, press the “test” button while the
spa jet unit is running. The spa jet unit
should shut off. Press the “reset” button.
The spa jet unit should resume normal oper-
ation. If the spa jet unit continues to run after
the “test” button is pressed, then the GFCI is
damaged. Do not use the RENEW 900 until
the GFCI has been repaired or replaced by a
qualified electrician.
9. Never insert any object into any opening.
10. Do not sit on the spa cover or place objects
on it. It is not designed to support weight.
11. Remove any water which may collect on the
spa cover.
12. Keep children and pets away from the
RENEW 900 when it is not in use.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Keep all electrical appliances such as radios, 27. WARNING—To reduce the risk of injury:
telephones, televisions, and lights at least
five feet (1.52 meters) away from the water.
Pregnant women should consult with their
physician before using the RENEW 900.
Pregnant women should not use the RENEW
900 if the water temperature is above 100°F
(38°C); the unborn child could be seriously
harmed.
21. A wire connector is provided on the pump
motor of this unit to connect a minimum No.
8 AWG (804 mm2) solid copper conductor
between this unit and any metal equipment,
electrical enclosure made of metal, metal
water pipes, or conduit within five feet
(1.52m) of the unit.
28. DANGER—To reduce the risk of drowning:
Prolonged immersion in the RENEW 900 may
cause hyperthermia, a dangerous condition
which occurs when the internal body temper-
ature rises several degrees above the normal
body temperature of 98.6°F. The symptoms of
hyperthermia are nausea, dizziness, drowsi-
ness, and fainting. Effects include: a lack of
awareness, inability to perceive heat or dan-
ger, and a greater risk of drowning due to a
loss of consciousness. Special note:
22. DANGER—Risk of electric shock: Do not set
up the RENEW 900 within five feet of any
metal objects or surfaces. As an alternative,
you may use the RENEW 900 within five feet
of metal objects if each metal object is per-
manently connected to the wire connector on
the pump motor of this unit by a minimum
No. 8 AWG (804 mm2) solid copper conductor
(see instruction 21).
Individuals suffering from hyperthermia may
be unable to realize that they must exit the
RENEW 900, and they also may be physically
unable to do so.
23. DANGER—Risk of drowning: Exercise
extreme caution to prevent unauthorized and
unsupervised use of the RENEW 900 by chil-
dren. Children must always be supervised.
29. WARNING—To reduce the risk of drowning:
Heat from the water, in conjunction with alco-
hol or drugs can cause unconsciousness. Do
not use the RENEW 900 if you are under the
influence of drugs or alcohol.
24. DANGER—To reduce the risk of drowning:
• Never use the RENEW 900 alone;
• Children should not use the RENEW 900
unless they are supervised by an adult;
• Keep pets away from the RENEW 900 at all
times;
30. WARNING—To reduce the risk of injury or
drowning: Consult your physician about pos-
sible side-effects of any medications you may
be taking before using the RENEW 900. Heat
from the water, in conjunction with some med-
ications may cause drowsiness and increase
the risk of drowning. Others can effect blood
pressure, heart rate, and circulation.
• Always replace and lock the spa cover
when the RENEW 900 is not in use.
25. WARNING—To reduce the risk of injury: The
water temperature should never exceed
104°F (40°C). Temperatures between 100°F
(38°C) and 104°F (40°C) are considered to be
safe for healthy adults. However, if you plan
to remain in the RENEW 900 for more than
10 to 15 minutes, a lower temperature is rec-
ommended. Lower temperatures are also rec-
ommended for children.
31. WARNING—To reduce the risk of injury: It is
especially important for persons over the age
of 35 or persons with pre-existing health
problems, such as obesity, heart disease,
high or low blood pressure, circulatory prob-
lems, or diabetes to consult your physician
before using this product.
26. WARNING—To reduce the risk of injury:
Always use an accurate thermometer to
determine the water temperature before
using the RENEW 900.
32. If you feel pain or dizziness at any time while
using the RENEW 900, discontinue use and
contact a physician.
WARNING: Read all instructions before using the RENEW 900. ICON assumes no responsibility for
personal injury or property damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING DECAL PLACEMENT
The decals shown below have been placed on the RENEW 900. If a decal is missing, or if it is not legible,
please call our Customer Service Department toll-free at 1-888-936-4266, Monday–Thursday, 8:00
am–6:30 pm; Friday, 8:00 am–6:00 pm EST (excluding holidays), to order a replacement decal. Apply the
decal in the location shown.
IMAGE® is a registered trademark of ICON Health & Fitness, Inc.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the IMAGE® RENEW 900. The Department toll-free at 1-888-936-4266, Monday–
innovative RENEW 900 offers the features and quality
of a traditional hot tub at an affordable price. Best of
all, the RENEW 900 is fully portable, so you can take
it wherever there is an electrical outlet. The RENEW
900 allows you to relax and unwind in the comfort of
your own home.
Thursday, 8:00 am–6:30 pm; Friday, 8:00 am–6:00 pm
EST(excluding holidays). To help us assist you,
please note the product model number and serial
number before calling. The model number is
831.100430. The serial number can be found on a
decal attached to spa jet unit (see the front cover of
this manual).
For your benefit, read this manual carefully before
using the IMAGE® RENEW 900. If you have addition-
al questions, please call our Customer Service
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Spa Cover
Console (Under
Spa Cover)
Spa Jet Unit
Power Cord
Side Panel
Ground Fault Circuit
Interrupter (GFCI)
Locking Buckle
Inflation Valve
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHOOSING A LOCATION FOR THE RENEW 900
There are many factors to consider when choosing a location to set up the RENEW 900. These factors vary
depending on whether you use the RENEW 900 inside or outside. We have listed several factors you may wish
to consider as you decide where you want to use the RENEW 900.
If you set up the RENEW 900 inside:
If you set up the RENEW 900 outside:
1. The RENEW 900 will increase the level of humidi-
ty in your home. The location you choose should
be well ventilated. You may need to install a venti-
lation fan or use a dehumidifier.
1. You should check your local building codes con-
cerning the use of outdoor spas.
2. The location must be close to an electrical outlet.
Do not use an extension cord with the RENEW
900.
2. The location must be close to an electrical outlet.
Do not use an extension cord with the RENEW
900.
3. The RENEW 900 should be close to a source of
water.
3. The RENEW 900 should be close to a source of
water.
4. We recommend that you place the RENEW 900
on a water- and stain-resistant, non-slip surface.
4. Do not use the RENEW 900 on carpet or other
material that may be damaged by moisture. We
recommend that you place the RENEW 900 on a
water- and stain-resistant, non-slip surface with a
floor drain for any water that may splash from the
RENEW 900.
5. Be sure that the location you choose is stable. It
must be able to support the weight of the RENEW
900 when it is filled with water, plus the weight of
the occupants. The RENEW 900 weighs approxi-
mately 2400 pounds when filled with water.
5. Be sure that the location you choose is stable. It
must be able to support the weight of the RENEW
900 when it is filled with water, plus the weight of
the occupants. The RENEW 900 weighs approxi-
mately 2400 pounds when filled with water.
6. Think about environmental factors, such as rain,
wind, shade, sunlight, and so forth.
7. You should be able to monitor the use of the
RENEW 900 from your home, to prevent unautho-
rized use by children.
6. Do not use the RENEW 900 above a finished liv-
ing area, due to the risk of water damage.
8. Be sure that there is room around the RENEW
900 to permit servicing of the unit. The diameter of
the tub is 69”. You should allow for this size, plus
the size of the spa jet unit, when choosing the
location.
7. Be sure that there is room around the RENEW
900 to permit servicing of the unit. The diameter of
the tub is 69”. You should allow for this size, plus
the size of the spa jet unit, when choosing the
location.
9. Be sure to note any other considerations, such as
aesthetics or privacy concerns, which may affect
the safety or enjoyment of using the RENEW 900.
8. Be sure to note any other considerations, such as
aesthetics or privacy concerns, that may affect the
safety or enjoyment of using the RENEW 900.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Before beginning assembly, carefully read the
following information and instructions:
• Assembly requires the included air pump.
• Read each assembly step before you begin.
• Place all parts in a cleared area and remove the
packing materials; do not dispose of the packing
materials until assembly is completed.
• During assembly, make sure that all parts are ori-
ented as shown in the drawings.
• Assembly requires two people.
1. Before beginning assembly, be sure that you
have read and understand the information in the
box above and on the previous page.
1
8
Unfold the pre-assembled Fabric Spa Surround (8)
and Side Panels (1, 2) until the assembled unit is
round.
Check the self-attaching connections between the
Fabric Spa Surround (8) and Side Panels (1, 2) to
be sure that all connections are firm. Be sure that all
six cover buckles are fully inserted through the slots
in the Side Panels (1, 2).
Buckle
1, 2
Slot
2. Unfold the Inflatable Spa Liner (9).
2
Attach the nozzle on the included air pump to the
valve on the side of the Inflatable Spa Liner (9). Use
the air pump to fill the sides of the Inflatable Spa
Liner with air.
Inflate here
second
9
Attach the nozzle on the air pump to the valve on
the floor of the Inflatable Spa Liner (9). Use the air
pump to fill the bottom of the Inflatable Spa Liner
with air.
Inflate here
third
Attach the nozzle on the air pump to the valve on
top of the Inflatable Spa Liner (9). Use the air pump
to fill the cushion on top of the Inflatable Spa Liner
with air.
Inflate here
first
3
3. Be sure that the flap on the Fabric Spa Surround (8)
is on the outside of the Fabric Spa Surround and
Side Panels (1, 2). Insert the Inflatable Spa Liner (9)
into the Fabric Spa Surround. Align the valve in the
Inflatable Spa Liner with the hole in the Fabric Spa
Surround and the Inflation Side Panel (2).
9
8—Flap
1, 2
Flip the flap on the Fabric Spa Surround (8) over the
low section of the Inflatable Spa Liner (9).
Valve must
be visible in
this hole
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Remove the power cord from the Spa Jet Unit (13).
4
With the help of a second person, place the Spa Jet
Unit (13) over the Side Panel (1) and the section of
the Inflatable Spa Liner (9) which does not have the
cushion. Be extremely careful not to tear the
Inflatable Spa Liner (9) as you slide the Spa Jet
Unit into place.
13
Power
Cord
9
1
5. Before you fill the RENEW 900, be sure that it is in
the position you want, and that it can be easily ser-
viced, if needed. Once the RENEW 900 is filled with
water, it will need to be drained to be moved.
5
9
13
Using a garden hose or other clean water source,
begin filling the RENEW 900, until the jet and filter
openings on the Spa Jet Unit (13) are covered with
water. Do not fill the RENEW 900 more than 20”
deep with water.
After the RENEW 900 is full, you must prime the
Spa Jet Unit (13) before using the RENEW 900
(see PRIMING THE SPA JET UNIT on page 10).
6. Attach the nozzle on the included air pump to the
valve on the Inflatable Cover (4). Use the Air Pump
to fill the Inflatable Cover (4) with air. Remove the
nozzle from the Inflatable Cover.
6
4
Slide one of the straps on the inside of the Spa
Cover (11) through one of the loops on the
Inflatable Cover (4). Attach the latch on the strap to
the buckle on the other end.
Latch and
Buckle
11
Attach the other three straps on the inside of the
Spa Cover (11) through the loops on the Inflatable
Cover (4) in the same manner.
7. Place the Spa Cover (11) over the Side Panels (1,
2) and the Spa Jet Unit (13). Be sure that the Spa
Cover is properly centered and that the straps
on the Spa Cover line up with the straps extend-
ing from the slots in the Side Panels (1, 2).
7
11
Snap each of the six latches on the Spa Cover (11)
into the buckles on the straps extending from the
slots in the Side Panels (1, 2).
13
1, 2
Latches and Buckles
9
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE RENEW 900
The RENEW 900 is designed for up to four adults.
The six water jets can be regulated to provide a relax-
ing massage to sooth away stress, and the strength
of the water massage can be adjusted by the air con-
trol. The RENEW 900 holds 300 gallons of water and
offers an automatic, programmable heating (70°F to
104°F) and filtration system.
or more amps. No other appliance should be on the
same circuit. Replace the power cord immediately if it
becomes damaged.
The power cord is equipped with a Ground Fault
Circuit Interrupter (GFCI), located at the end of the
power cord. You should always test the GFCI before
using the RENEW 900.
The guidelines below explain how to properly use the
RENEW 900. Follow these guidelines to maintain the
RENEW 900 for your long-term enjoyment.
First, turn on the RENEW 900 by pressing the power
button on the console. Once the unit is running, press
the GFCI “test” button. The RENEW 900 should shut
off. Press the “reset” button. The RENEW 900 should
resume normal operation. If the RENEW 900 contin-
ues to run after the “test” button is pressed, then the
GFCI is damaged. Do not use the RENEW 900 until
the GFCI has been repaired or replaced by a qualified
electrician.
PRIMING THE SPA JET UNIT
The water pump in the spa jet unit must be primed
before you use the RENEW 900 the first time. You
must also prime the pump before using the unit each
time you re-fill the RENEW 900.
STARTING THE RENEW 900
To prime the spa jet
unit, remove the
Once you have tested the GFCI, you should verify the
water flow from the pumping unit. Set the air control
on the console to the lowest setting (see USING THE
CONSOLE on the next page). The pumping unit will
heat the water as it pumps. Cover the RENEW 900
with the spa cover. The spa cover must be tight.
The water will heat at about 1.7°F an hour with the
cover on. If you are using the RENEW 900 indoors,
and the room temperature is maintained at 70°F, it will
take approximately 20 to 28 hours for the water to
reach the set temperature.
primer cap from the
console. Fill the spa
jet unit with at least 64
Cap
oz. of water. Replace
and tighten the
primer cap. IMPOR-
TANT: The spa jet
unit may be seriously damaged if the pump is not
properly primed, or if the primer cap is not
replaced and fully tightened.
Primer
PLUGGING IN THE RENEW 900
The temperature and water flow can be set or
changed by the controls on the console (see USING
THE CONSOLE on the next page).
Once the RENEW 900 is filled with enough water to
cover the water jets and the pump has been primed,
the power cord can be plugged in and the spa jet unit
can be turned on. Note: The first time the power cord
is plugged in, the spa jet unit will turn on automatically.
TESTING AND TREATING THE WATER
The RENEW 900 comes with a starter chemical pack
for maintaining the water in the spa. Disregard the
directions on the individual packages of “QUICK pHix
It DOWN” and “QUICK pHix It UP.” However, the
directions on the bottle of “Non-chlorine Shox” and
“Bromine Base” are correct. Always keep the chemi-
cals away from children and pets.
When connecting the power cord, plug the power cord
directly into a grounded circuit capable of carrying 15
Grounded circuit capable of
carrying 15 or more amps
The first time you use the spa, you should test and
treat the water. Once you have verified that the spa
jet unit is functioning properly, and have allowed the
water to circulate for a while, you should remove the
spa cover and add 1/3 of the “Bromine Base” bottle,
and 1/3 of the “Non-chlorine Shox” bottle to the water
in the spa. Allow the water to circulate for five min-
utes. You should now test the pH level of the water.
Use the included test strips to check the pH of the
Test and Reset
Buttons
GFCI
10
Download from Www.Somanuals.com. All Manuals Search And Download.
water. Refer to the instructions on the test strip pack-
aging to see how to use the test strips.
SECURING THE SPA COVER
The spa cover can be secured by snapping the latch-
es on the spa cover into the buckles on the side panels.
If the level is too low, add half of one of the “QUICK
pHix It UP” packets to the water. Let the water circu-
late through the spa jet unit for five minutes. Test the
pH level again. Repeat until the pH level is correct.
The buckles can be
locked by inserting the
key and turning it
Latch
If the level is too high, add half of one of the “QUICK
pHix It DOWN” packets to the water. Let the water cir-
culate through the spa jet unit for five minutes. Test
the pH level again. Repeat until the pH level is correct.
clockwise a quarter
turn. To unlock the
buckles, insert the key
and turn it counter-
clockwise a quarter
turn.
Buckle
Key
Replace the spa cover and allow the water to contin-
ue to heat.
Always keep the buckles locked when the spa is
not in use. Keep the keys in a safe place, out of
the reach of children.
See WATER CHEMISTRY on page 13 for information
concerning proper water maintenance.
DIAGRAM OF THE CONSOLE
USING THE CONSOLE
Refer to the console diagram above. The function of
each console control is explained below:
On/Off: Turns the spa jet unit on and off. When you
first press the on/off button, the spa jet unit will run at
low speed, providing gentle hydrotherapy. Press the
button again and the spa jet unit will run at high
speed, providing more intense hydrotherapy. Press
the button a third time and the spa jet unit will shut
off.
Primer: This opening allows you to prime the spa jet
unit before operation (see PRIMING THE SPA JET
UNITon page 10).
Diverter: Controls the flow of water through the
hydro-therapy jets and the whirlpool jet. The direction
of the flow can be adjusted by turning the diverter
control. When the control is set to “front,” the flow will
be through the hydro-therapy jets; when it is set to
“side,” the flow will be through the whirlpool jet; when
it is set to “all,” the flow will be evenly distributed
through both the hydro-therapy jets and the whirlpool
jet.
The spa jet unit also features an automatic mode,
which heats and filters the water when the spa is left
unattended. When the spa jet unit is first plugged in,
or if the buttons on the console have not been used
for longer than twenty minutes, the automatic mode
will begin filtering or heating the water, as needed.
Note: to keep the filter and heat cycles from run-
ning, the power cord must be unplugged.
Thermostat: Controls the temperature of the water.
The water heats at about 1.7°F an hour with the cover
on. The thermostat can be set to heat the water from
70°F to 104°F. Use a medical or other accurate ther-
mometer to check the temperature of the water.
Air Control: Determines the amount of air that is in
the spa jet system during operation. If the control is
turned to the left, the amount of air flowing through
the jets will increase. If the control is turned to the
right, the amount will decrease.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SPA JET UNIT OPERATION
ing the water for twenty minutes to filter any impuri-
ties. Also, if the water temperature falls below 40°F,
the pump will begin circulating and heating the water
to prevent the water from freezing.
The spa jet unit features five hydro-therapy jets, a
whirlpool jet, a suction vent, and a filter housing.
The five hydro-therapy jets (A), located on the front
of the spa jet unit, focus the water massage on your
neck and back.
DRAINING THE RENEW 900
To drain the RENEW 900, you must use a garden
hose to siphon the water. Place one end of the hose
in the RENEW 900 and hold it in front of a hydro-
therapy jet until there is a flow of water coming out of
the hose. Turn off the spa unit and unplug the
power cord. The unit will be damaged if it is run
without water circulating. Be sure the end of the
hose in the RENEW 900 is on the floor of the spa.
B
A
D
C
The whirlpool jet (B), located on the left side of the
spa jet unit, directs the flow of the water to create a
whirlpool action in the RENEW 900.
The suction vent (C),
located on the right
side of the spa jet
unit, pulls the water
into the spa unit, in
order to operate the
system. The suction
cover should always
be in place over the
suction vent. Never
operate the RENEW
900 without the suc-
tion cover in place.
DRAINING THE PUMP
After the RENEW 900 is drained (see DRAINING
THE RENEW 900 above), the pump in the spa jet unit
should also be drained if the RENEW 900 will be
stored for more than thirty days, or if it may be
exposed to freezing temperatures.
C
To drain the pump,
remove the spa jet
unit from the side pan-
els. Be careful not to
tear the inflatable
spa liner. Locate the
pump inside the spa
jet unit. Remove the
drain plug from the
pump. Tip the spa jet
unit slightly, until all the water has drained from the
pump. Replace the drain plug.
The filter (D), is locat-
ed on the left side of
the spa jet unit,
behind the filter cover.
Pump
Filter Cover
Screws
The filter can be
Filter Cover
D
removed for cleaning
and replacement by
removing the Filter
Cover and the two
filter cover screws and then pulling the filter from the
spa jet unit.
Drain Plug
The spa jet unit features an automatic filter cycle and
freeze protection. If the spa jet unit has not been
operated for three hours, the pump will begin circulat-
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CLEANING THE INFLATABLE SPA LINER
4. Keep all chemicals out of the reach of chil-
dren and pets.
The liner should be cleaned with a mild soap solution.
Do not use solvents. The liner should always be clean
and dry before being moved or stored.
5. Keep all containers closed tightly when
not in use.
6. Never add water to the chemicals—always
add the chemicals to the water as directed.
7. Always store chemicals in a cool, dry place.
8. Always keep chemicals away from chil-
dren and pets.
CHECKING AND CLEANING THE FILTER
The filter should be checked periodically for build-up
of dirt and oil. If the filter needs to be cleaned, follow
the steps below:
MAINTAINING THE PROPER PH BALANCE
1. Turn off the power.
2. Remove the two screws and cover from the
spa jet. Then pull the filter out of the unit.
3. Check the filter for any dirt or debris. If the fil-
ter needs to be cleaned, rinse the filter with a
hose. If the filter still is dirty, you will need to
soak it in a cleaning solution which can be
obtained from a pool and spa supply store.
4. Inspect the filter for damage. Replace the fil-
ter if there are any signs of damage.
The pH factor is a measure of relative acidity or alka-
linity in the water. It is measured on a scale of 1 to 14.
Pure water has a value of 7, which is neutral. Any
value above 7 is alkaline, and any value below 7 is
acidic. You should maintain a slightly alkaline pH
level, between 7.2 and 7.8, in the RENEW 900.
Severe problems can occur when the pH balance is
not maintained within this range. If the pH level
5. Re-insert the cleaned filter and re-attach the
two screws and cover to the spa jet unit.
exceeds 7.8, dissolved minerals can build-up and clog
the plumbing in the spa jet unit. If the pH level falls
below 7.2, the acid level in the water will begin to cor-
rode the metal parts in the spa jet unit. Also, the sani-
tation agents in the water will not be effective if the pH
level is not properly maintained. Damage caused by
improper pH levels is not covered under the warranty.
MAINTAINING THE SPA COVER
The spa cover should be cleaned monthly. Remove
the inflatable cover from the spa cover, then hang the
spa cover over a clothes line and spray it with a hose.
Leave the cover on the clothes line until it is fully dry.
To maintain the proper pH level, you should test the
pH of the water regularly. To test the water you can
either purchase additional test strips or purchase a pH
test kit at a pool and spa supply store. The pH read-
ing should be between 7.2 and 7.8. If the level is too
low, add a pH increaser (usually soda ash). If the
level is too high, add a pH reducer (usually sodium
bisulfate). Test the water again after five minutes. See
the instructions with your test strips or pH test kit for
additional information about testing and adjusting the
pH.
WINTER USE AND CARE
The RENEW 900 is designed for year-round use. If
you decide to store the RENEW 900 for the winter,
store it in a warm, dry location. (See DRAINING THE
RENEW 900 and DRAINING THE PUMP on page 12.)
WATER CHEMISTRY
The RENEW 900 comes with a starter chemical pack
for maintaining the water in the spa. (See TESTING
AND TREATING THE WATER on page 10.) Additional
chemicals can be purchased at a pool and spa supply
store.
SANITIZING THE RENEW 900
Please refer to your local pool and spa supplier for
information concerning which chemicals you should
use in your area to sanitize the spa.
CAUTION: The chemicals used to maintain the pH
balance of the water and to sanitize the water can
be dangerous. Always follow these basic guide-
lines when handling the chemicals:
1. Always read and follow the directions on
the label, unless directed otherwise.
2. Never mix different chemicals.
The most common sanitizing agent is a solid bromine
concentrate. The amount required varies according to
several factors, such as user load, temperature, water
conditions, and so forth.
Proper water maintenance is a fairly complex process.
We recommend that you contact your local pool and
spa supplier for information on how you should best
accomplish this.
3. Do not exceed the recommended
amounts—follow the directions on the
label closely.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
-
TROUBLE SHOOTING
Most problems can be solved by following the simple steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, call our Customer Service Department toll-free
at 1-888-936-4266, Monday–Thursday, 8:00 am–6:30 pm; Friday, 8:00 am–6:00 pm EST (excluding holi-
days).
1. SYMPTOM: THE SPA WILL NOT OPERATE
the air control to low. The water will heat at a
rate of 1.7°F an hour. If you are using the spa
indoors, and the room temperature is main-
tained at 70°F, it will take approximately 20 to
28 hours for the water to reach the set temper-
ature.
a. Check the power cord. The power cord must
be plugged into a grounded outlet (see PLUG-
GING IN THE RENEW 900 on page 10).
b. Check to see if the GFCI breaker is tripped, or
was not turned on. Reset the GFCI breaker.
b. If you are using the RENEW 900 outdoors, it
may take longer for the water to heat. See the
chart below for the approximate heating time.
2. SYMPTOM: THE CIRCUIT BREAKER OR GFCI
BREAKER TRIPS WHILE THE SPA IS
OPERATING
Air Temperature
Heating Time
20 to 28 hours
1 to 2 days
+
70°F
a. Reset the circuit breaker. If the circuit breaker
trips again, contact a qualified electrician for
service.
50°F–70°F
30°F–50°F
2 to 3 days
b. If the water still has not heated after three
days, contact our customer service department.
3. SYMPTOM: THE PUMP HUMS
a. The filter may be dirty or damaged. Remove
the filter housing from the spa jet unit and clean
or replace the filter.
7. SYMPTOM: THE WATER PULSATES OR
THERE IS MINIMUM WATER FLOW
a. Adjust the water level. This usually occurs only
when the water level is low. Add water until the
filter and jets are covered.
b. The pump may have a foreign object stuck in
the impeller. Contact our customer service
department.
b. This problem is caused by excess air in the
pump circulation system. Check to see if the
primer cap is fully tightened. Prime the pump
again and fully tighten the primer cap (see
PRIMING THE SPA JETUNITon page 10).
c. The pump may have a loose wire connection.
Contact our customer service department.
4. SYMPTOM: THE PUMP HUMS BUT DOES NOT
ROTATE
8. SYMPTOM: THE SPA JET UNIT CAVITATES
DURING USE
a. The pump may be jammed. Contact our cus-
tomer service department.
a. Adjust the water level. This usually occurs only
when the water level is low. Add water until the
filter and jets are covered.
5. SYMPTOM: THE PUMP IS NOISY WHILE
OPERATING
a. There may be debris in the pump. Contact our
customer service department.
b. This problem is caused by excess air in the
pump circulation system. Check to see if the
primer cap is fully tightened. Prime the pump
again and fully tighten the primer cap (see
PRIMING THE SPA JETUNITon page 10).
b. The pump may have a bad bearing. Contact
our customer service department.
6. SYMPTOM: THE WATER DOES NOT HEAT
9. SYMPTOM: THE WATER IS NOT BEING
CLEANED BY THE FILTER
a. The heater is attached to the pump in the spa
jet unit. If the pump is operating, the water
should heat. Cover the RENEW 900 with the
spa cover. The spa cover must be tight. Set
a. Check to see if the filter is in place. Clean the
filter if it is dirty.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
b. Check the chemical balance of the water. If the
pH is incorrect, the sanitizing agents will not
function properly.
11. SYMPTOM: THE WATER LEVEL DROPS
a. Some water loss due to evaporation is normal.
If rapid water loss occurs, or if you notice wet-
ness on the floor around the RENEW 900, then
the liner may have a leak. Locate the leak, and
patch it using a pool patch kit that you can pur-
chase at any pool and spa supply store.
10. SYMPTOM: THE SPA JET UNIT CONTINUES
TO RUN AFTER IT HAS BEEN SHUT OFF
a. When you press the on/off button once, the spa
jet unit will run at low speed, heating the water.
Press the button again and the spa jet unit will
run at high speed, filtering the water. Press the
button a third time and the spa jet unit will shut
off. The spa jet unit also features an automatic
mode, which heats and filters the water when
the spa is left unattended. When the spa jet
unit is first plugged in, or if the buttons on the
console have not been used for longer than
twenty minutes, the automatic mode will begin
filtering or heating the water, as needed. To
keep the filter and heat cycles from running,
the power cord must be unplugged. Special
Note: If the unit is to be kept outdoors in
cold weather, you must allow the spa to
maintain a safe temperature by running in
automatic mode. Allowing the spa jet unit to
freeze will damage the unit. If you do not
want to use the spa during the winter, store
it in a warm, dry location (see WINTER USE
AND CARE on page 13).
b. A clamp or seal inside the spa jet may be
loose. Check the floor around the spa jet unit
for excess water, and watch the spa jet unit
while it is operating to see if water drips from
the spa jet unit housing. If you can identify the
location of the leak inside the spa jet unit, tight-
en the clamp or replace the damaged seal.
12. SYMPTOM: THE INFLATABLE SPA LINER
LOSES AIR
a. Over time, some air loss is normal. If rapid air
loss occurs, then the liner may have an air
leak. Locate the leak, and patch it using a pool
patch kit that you can purchase at any pool and
spa supply store.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-888-936-4266,
Monday–Thursday, 8:00 am–6:30 pm; Friday, 8:00 am–6:00 pm EST (excluding holidays). To help us assist you,
please be prepared to give the following information when calling:
1. The MODEL NUMBER of the product (831.100430).
2. The NAME of the product (IMAGE® RENEW 900).
3. The SERIAL NUMBER of the product (see the front cover of this manual).
4. The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST/EXPLODED DRAWING attached to
the center of this manual).
Part No. 154868 J00726-C R0499A
Printed in USA © 1999 ICON Health & Fitness, Inc.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CUSTOMER RECORD
Model No.:
Serial No.:
Retailer Name:
Retailer Address:
Purchase Date:
PLACE
STAMP
HERE
ICON of Canada Inc.
900 de l’Industrie
St-Jérôme, Québec
Canada, J7Y 4B8
18
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED FIVE YEAR MASSAGE SPA WARRANTY
ICON OF/DU CANADA INC., (ICON), warrants this product to be free from defects in workmanship and material, under nor-
mal use and service conditions, for a period of ninety (90) days from the date of purchase. ICON extends a limited five (5)
year warranty on the spa shell structure. ICON also extends a limited two (2) year warranty on the pump and motor. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at
ICON's option, the product through one of its authorized service centers. All repairs for which warranty claims are made must
be pre-authorized by ICON. This warranty does not extend to any product or damage to a product caused by or attributable
to freight damage, abuse, misuse, improper or abnormal usage, or repairs not provided by ICON authorized service per-
sonnel, to products used for commercial or rental purposes, or to products used as store display models. Specifically exclud-
ed are damages caused by or attributable to the following incidents: any damage to the wood exterior resulting from improp-
er maintenance, or any damage to the wood or tile exterior attributable to freight mishandling; damage resulting from improp-
er winterization; damage to the spa shell resulting from improper chemical treatment, damage to the spa shell resulting from
exposure to extreme temperatures, or damage to the spa shell resulting from exposure to direct sunlight and ultraviolet rays
while the spa is empty; damage to the pump, motor, plumbing, and components due to improper maintenance, chemical
treatment, or exposure; damage resulting from failure to properly follow user’s manual installation, operating, or mainte-
nance instructions. Also excluded are consumable components, including but not restricted to headrests, filter cartridges,
and light bulbs. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use
or performance of the product or damages with respect to any economic loss, loss of or damage to property including water
damage, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages
of whatsoever nature. Some provinces do not allow the exclusion or limitation of incidental or consequential damages.
Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or
fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some provinces do not allow
limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from province to province.
ICON OF/DU CANADA, 900 de l’Industrie, St. Jerôme, QC J7Y 4B8
™
o f / d u C a n a d a I n c .
PRODUCT WARRANTY REGISTRATION
IMPORTANT: MAIL WITHIN 14 DAYS OF PURCHASE
NAME:
ADDRESS:
COUNTY:
PHONE:
POSTCODE:
MODEL NO.
RETAILER NAME:
SERIAL NO.
PURCHASE DATE:
RETAILER ADDRESS:
1) Primary user(s) of product:
8) Did you consider purchasing fitness equipment from another
manufacturer?
❏❏❏Male
❏❏❏Female
❏❏❏Family
❏ 55–64
❏ No
❏ Yes
2) Age of primary user:
❏❏❏0–24
What other Manufacturer?
❏ 35–44
❏ 45–54
❏ 25–34
❏ 65 and over
9) Based on your impression of what you have purchased,
would you buy another ICON product?
3) Annual household income:
❏ Yes
❏ No
❏ No Opinion
❏ 0–9,999
❏ 15,000–19,999
If not, what other brand name equipment would you purchase?
❏ 10,000–14,999
❏ 20,000+
4) How many times a week do you exercise?
10) What other type of exercise equipment do you own?
❏ Less than 3 times ❏ 3 times or more
❏ Bicycle
❏ Exercise Cycle ❏ Treadmill
❏ Weight Bench ❏ Stepper
❏ Other
❏ Home Gym
❏ Cardio Glide
5) Have you ever purchased an ICON product before?
❏ Yes ❏ No
11) Which type of magazines do you read regularly?
6) Where did you first see or hear about ICON products?
❏ Sports
❏ Fitness
❏ Motoring
❏ Magazine
❏ Newspaper Ad
❏ Other
❏ Friend/relative
❏ Business
❏ Computer
❏ General
❏ Store
12) Do you wish to be sent further bulletins about ICON products?
❏ Yes ❏ No
7) What was the primary reason for purchasing this ICON product?
❏ Store Employee ❏ TelevisionAds ❏ Colour
❏ Electronic Features ❏ Magazine Ads ❏ Price
THANK YOU FOR YOUR TIME
© 1999 ICON of Canada, Inc. Printed in USA
❏ Product Design
❏ Other Features
❏ Product Innovation
17
Download from Www.Somanuals.com. All Manuals Search And Download.
REFERENCES
No. du Modèle:
No. de Série:
Date d’Achat:
Nom du Détaillant:
Adresse du Détaillant:
AFFRANCHIR
SUFFISAMMENT
ICON of/du Canada Inc.
900 de l’Industrie
St-Jérôme, Québec
Canada, J7Y 4B8
18
Download from Www.Somanuals.com. All Manuals Search And Download.
GARANTIE LIMITÉE DE CINQ ANS
ICON du CANADA, Inc. (ICON), garantie que ce produit n’a aucun défaut de fabrication ou de matériaux, sous utilisation et main-
tenance normale, pour une période de quatre-vingt-dix (90) jours après la date d’achat de ce produit. ICON rallonge une garantie
limitée pendant cinq (5) ans sur la structure du jacuzzi. ICON rallonge aussi une garantie limitée de deux (2) ans pour la pompe
et le moteur. Cette garantie est rallongée seulement pour l’acheteur original. L’obligation d’ICON sous cette garantie est limitée
au remplacement ou aux réparations, au choix d’ICON, du produit par un des centres de service autorisés. Toutes réparations
qui sont soumises sous la garantie doivent être pré-approuvées par ICON. Cette garantie ne comprend pas les dommages
causés ou dues au transport, abus, mauvais usage, ou réparations faites par une personne non-autorisée par ICON, aux pro-
duits utilisés pour une utilisation commerciale ou pour la location, ou aux produits utilisés pour l’exposition en magasin. Les dom-
mages causés ou attribués aux incidents suivants sont exclus de la garantie: les dommages faits au bois du jacuzzi causés par
un mauvais entretien, ou tout dommage fait au bois ou aux panneaux extérieurs causés par un mauvais transport; les dommages
causés par le froid, la pluie ou le gel; les dommages faits à la structure du jacuzzi dues à un mauvais usage des produits chim-
iques, à des températures extrêmes, ou à une exposition prolongée aux rayons directes du soleil et des ultra-violet quand le
jacuzzi est vide; les dommages à la pompe, au moteur, à la canalisation et aux pièces dues à un mauvais entretien, aux produits
chimiques, ou à l’exposition; les dommages résultants de ne pas lire les instructions d’assemblage et de fonctionnement con-
tenus dans le livret d’instructions. Les pièces usables sont aussi exclus telles que, mais non restrictées à, appui-tête, cartouch-
es du filtre, et ampoules. ICON n’autorise aucune autre garantie à part celles spécifiquement mentionnées ci-dessus.
ICON ne pourra être tenu responsable d'aucun dommage indirect, spécial ou accessoire résultant ou ayant trait à l'utilisation ou
au fonctionnement du produit, aux pertes d'argent, de biens, de revenus ou de profits, aux pertes de jouissance, aux frais de
déménagement, d'installation ou à tous dommages accessoires de quelque nature qu'ils soient. Dans certaines provinces, il est
interdit d'exclure ou de restreindre la responsabilité pour les dommages indirects ou accessoires de sorte que la restriction qui
précède pourrait ne pas s'appliquer dans certains cas.
La présente garantie remplace toutes les garanties dont notamment les garanties implicites de valeur marchande ou d'aptitude
à un usage et est limitée dans sa durée et sa portée par les clauses spécifiques contenues dans la présente garantie. Certaines
provinces n'autorisent pas la restriction de la durée d'une garantie de sorte que la restriction qui précède pourrait ne pas s'appli-
quer dans certains cas ou spécifiés par votre détaillant d’équipement de sports.
Cette garantie vous confère des droits légaux spécifiques. Vous pouvez avoir d'autres droits qui peuvent varier d'une province à
l'autre ou spécifier par votre détaillant d’équipement de sports.
ICON OF/DU CANADA INC., 900 de l‘Industrie, St-Jérôme, QC, J7Y 4B8
™
o f / d u C a n a d a I n c .
FORMULAIRE DE GARANTIE DU PRODUIT
IMPORTANT: POSTEZ DANS LES 14 JOURS SUIVANT L’ACHAT
NOM:
ADRESSE:
PAYS:
NO. DE MODÈLE:
NOM DU DÉTAILLANT:
TÉLÉPHONE:
CODE POSTAL:
NO. DE SÉRIE:
DATE D’ACHAT:
ADRESSE:
1) Usager principal du produit:
8) Avez-vous déjà considéré l’achat d’un produit fabriqué par un
autre manufacturier?
❏❏Homme
❏❏Femme
❏❏Famille
❏ Non
❏ Oui
2) Âge de l’usager principal:
❏❏0–24
Si oui, lequel?
❏ 35–44
❏ 45–54
❏ 55–64
❏ 25–34
❏ 65 et plus
9) Basé sur votre impression du produit, achèteriez-vous un
autre produit ICON?
3) Revenu annuel:
❏ 0–9,999
❏ Oui
❏ Non
❏ Sans opinion
❏ 15,000–19,999
❏ 20,000+
Sinon quelle marque achèteriez-vous?
❏ 10,000–14,999
10) Possédez-vous d’autre équipement d’exercice?
❏ Bicyclette ❏ Bicyclette stationnaire ❏ Tapis
roulant
❏ Appareil de musculation ❏ Banc d’exercice
❏ Simulateur d’escalier ❏ Cardio Glide ❏ Autre
4) Combien de fois par semaine faites-vous de l’exercice?
❏ moins que 3 fois ❏ 3 fois et plus
5) Avez-vous déjà acheté un produit ICON?
❏ Oui ❏ Non
6) Comment avez-vous entendu parler des produits ICON?
❏ Publicité dans un journal ❏ Magasin
❏ Magazine ❏ Ami/Parent ❏ Autre
11) Quel type de magazine lisez-vous régulièrement?
❏ Sports
❏ Général
❏ Automobilisme
❏ Affaires
❏ Ordinateur ❏ Mise en forme
7) Quel est votre raison principale pour avoir choisi un produit ICON?
❏ Employé du magasin ❏ Publicité à la télévision
12) Désirez-vous recevoir de l’information supplémentaire sur les
produits ICON?
❏ Options électroniques ❏ Publicité dans un magazine
❏ Oui
❏ Non
❏ Modèle du produit
❏ Couleur
❏ Innovation du produit
❏ Prix
❏ Autres aspects
MERCI DE VOTRE TEMPS
1999 © ICON du/of Canada, Inc.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. 831.100430
R0499A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
4
4
4
1
1
4
1
2
1
1
2
1
1
1
1
1
1
1
1
2
1
1
1
4
1
4
4
1
Side Panel
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
#
1
1
1
1
1
1
16
1
1
2
2
1
2
5
1
2
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
Rubber Damper
Wire Harness
Air Control Knob
On/Off Switch Assembly
Thermostat Knob
Primer Cap
Housing Screw
Console Overlay
Micro Switch/Wire
Control Mounting Screw
Control Mounting Nut
Motor Mount Bracket
Housing Support Bracket
Cable Clamp
Power Cord Grommet
Dual Temperature Probe
Inflatable Cover
Clamp Screw
Clamp
Bolt
Fabric Spa Surround
Inflatable Spa Liner
Spa Jet Nozzle
Spa Cover
Heater O-ring
Spa Jet Unit
Heater Housing
Filter Cover Screw
Filter
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Filter Cover
3/8” Compression Fitting
Temperature Tube
Trim
Primer O-ring
Short Head Fitting
Motor Endcap
Motor Cap Screw
Pressure Switch
Heater Ground Wire
Air Pump
Cover Screw
Suction Cover
Suction Fitting
Pump Motor
Heater Terminal Cover
Heat Controller
Heater Wire Harness
Cover Nut
Electronic Control
Tri-jet Nozzle
Headrest w/Fasteners
Nut
Heat Control Nut
Rubber Insulator
Washer
#
#
#
#
#
#
#
Key
Starter Chemical Pack
Chemical Test Strip Pack
Warning Decal
User’s Manual
Video
Whirlpool Jet
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
11
4
9
8
1
Download from Www.Somanuals.com. All Manuals Search And Download.
19
18
46
38
51
17
40
36
6
35
12
27
39
39
5
5
37
29
23
10
6
52
26
13
10
50
55
24
14
22
47
10
32
21
52
16
2
15
54
53
41
20
45
7
31
30
48
49
42
3
48
28
33
25
43
44
34
Download from Www.Somanuals.com. All Manuals Search And Download.
|