USER MANUAL
ENGLISH
DEUTSCH
FRANCAIS
NEDERLANDS
Thank you very much for choosing the
iiyama LCD monitor.
ITALIANO
POLSKI
We recommend that you take a few
minutes to read carefully through this
brief but comprehensive manual before
installing and switching on the monitor.
Please keep this manual in a safe
place for your future reference.
PLE2001_3WS_WSV-e-M034B01.P65
1
2007/09/11, 10:12
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC DECLARATION OF CONFORMITY
Model Number:
Trade Name:
PL2000
iiyama
Responsible party:
Address:
Ampronix Inc.
8697 Research Dr. Irvine, CA.92618 U.S.A.
949-788-9930
Telephone number:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for Class B Personal Computers and
peripherals, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the device is operated in a residential environment. This device generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If you determine the device does cause harmful interference to radio
or television reception (this may be determined by monitoring the interference while turning the device off and
on), you are encouraged to try to correct the interference by one of the following measures:
„
„
„
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which the receiver
is connected.
„
Consult the dealer or an experienced radio or TV technician for help.
To meet the FCC requirements, you should use a signal cable with ferrite core at both ends.
CAUTION
Changes or modifications not expressly approved by IIYAMA could void the users authority
to operate the device under FCC compliance regulations.
CANADIAN DEPARTMENT OF COMMUNICATIONS COMPLIANCE
STATEMENT
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as
set out in the radio interference regulation of the Canadian department of communications.
CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” and 73/23/
EEC “Low Voltage Directive” as amended by Directive 93/68/EEC.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas,
business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings.
All places of operation are characterised by their connection to the public low voltage power supply system.
„ We reserve the right to change specifications without notice.
„ All trademarks used in this user manual are the property of their respective owners.
„ As an ENERGY STAR® Partner, iiyama has determined that this product meets the ENERGY STAR® guidelines for
energy efficiency.
PLE2001_3WS_WSV-e-M034B01.P65
3
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
FOR YOUR SAFETY..............................................................................
SAFETY PRECAUTIONS .................................................................
SPECIAL NOTES ON LCD MONITORS .............................................
CUSTOMERSERVICE ......................................................................
CLEANING .......................................................................................
1
1
3
3
3
BEFOREYOU OPERATETHE MONITOR ................................................
FEATURES .......................................................................................
CHECKINGTHE CONTENTS OFTHE PACKAGE .............................
HOWTO USE THE STAND ..............................................................
CONTROLSAND CONNECTORS ....................................................
CONNECTINGYOURMONITOR ......................................................
COMPUTERSETTING .......................................................................
ADJUSTINGTHE VIEWINGANGLE .................................................
4
4
4
5
6
7
8
8
OPERATINGTHEMONITOR ...................................................................
9
ADJUSTMENTMENUCONTENTS .................................................... 10
SCREENADJUSTMENTS ................................................................. 14
POWER MANAGEMENTFEATURE .................................................. 17
TROUBLE SHOOTING ............................................................................ 18
RECYCLINGINFORMATION ................................................................... 19
APPENDIX .............................................................................................. 20
SPECIFICATIONS ............................................................................. 20
DIMENSIONS .................................................................................... 24
COMPLIANTTIMING ......................................................................... 24
CONNECTORPINASSIGNMENT ...................................................... 25
Regulatory information : The high efficiency LCD backlights used in this
product contains 5mg or less of Mercury, the disposal of which may be
regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or
the Electronic Industries Alliance (www.eiae.org).
This information is only for U.S.A..
We recommend recycling of used product. Please contact your dealer or iiyama service
center. Recycle information is obtained via the Internet, using the address:
You can access the Web page of different countries from there.
PLE2001_3WS_WSV-e-M034B01.P65
4
2007/10/02, 13:05
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR YOUR SAFETY
SAFETY PRECAUTIONS
WARNING
STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor
and contact your dealer or iiyama service center immediately. Further use may be dangerous and
can cause fire or electric shock.
NEVER REMOVE THE CABINET
High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of
fire or electric shock.
DO NOT PUT ANY OBJECT INTO THE MONITOR
Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug
your monitor immediately and contact your dealer or iiyama service center. Using the monitor with
any object inside may cause fire, electric shock or damage.
INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
The monitor may cause an injury if it falls or is dropped.
DO NOT USE THE MONITOR NEAR WATER
Do not use where water may be splashed or spilt onto the monitor as it may cause fire or electric
shock.
OPERATE UNDER THE SPECIFIED POWER SUPPLY
Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will
cause malfunction and may cause fire or electric shock.
PROTECT THE CABLES
Do not pull or bend the power cable and signal cable. Do not place the monitor or any other heavy
objects on the cables. If damaged, the cables may cause fire or electric shock.
ADVERSE WEATHER CONDITIONS
It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in
power may cause malfunction. It is also advised not to touch the plug in these circumstances as it
may cause electric shock.
FOR YOUR SAFETY
1
PLE2001_3WS_WSV-e-M034B01.P65
5
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
INSTALLATION LOCATION
Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky
areas as it may cause fire, electric shock or damage. You should also avoid areas where the sun
shines directly on the monitor.
DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
The monitor may topple and cause injury if not suitably located. Please also ensure that you do not
place any heavy objects on the monitor, and that all cables are routed such that children may not pull
the cables and possibly cause injury.
MAINTAIN GOOD VENTILATION
Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause
fire. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls.
Do not remove the tilt stand when operating the monitor. Ventilation slots on the back of the cabinet
will be blocked and the monitor may overheat if the stand is removed. This may cause fire or damage.
Operating the monitor on its back, side, upside down or on a carpet or any other soft material may
also cause damage.
DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal
cable is disconnected. If you do not disconnect them, it may cause fire or electric shock.
UNPLUG THE MONITOR
If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid
accidents.
HOLD THE PLUG WHEN DISCONNECTING
To disconnect the power cable or signal cable, always pull it by the plug. Never pull on the cable itself
as this may cause fire or electric shock.
DO NOT TOUCH THE PLUG WITH WET HANDS
Pulling or inserting the plug with wet hands may cause electric shock.
WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may damage
your computer.
DO NOT PUT FLOPPY DISKS NEAR THE SPEAKERS
Magnetically recorded data, such as on a floppy disk, may become corrupted by the magnetic field
produced by the speakers if the disks are placed on or near the speakers.
OTHERS
ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room. For
optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches)
away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour
is recommended as looking at the screen continuously can cause eye strain.
2
FOR YOUR SAFETY
PLE2001_3WS_WSV-e-M034B01.P65
6
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitors and do not indicate a problem.
When you first turn on the LCD monitor, the picture may not fit in the display area
because of the type of computer that is used. In this case, adjust the picture
position to the correct position.
NOTE
„
Due to the nature of the backlight, the screen may flicker during initial use. Turn off
the Power Switch and then turn it on again to make sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the desktop
pattern you use.
„
„
„
Due to the nature of the LCD screen, an afterimage of the previous screen may
remain after switching the image, when the same image is displayed for hours. In
this case, the screen is recovered slowly by changing the image or turning off the
Power Switch for hours.
„
Contact your dealer or iiyama service center for the backlight replacement when the
screen is dark, flickering or not lighting up. Never attempt to replace it by yourself.
CUSTOMER SERVICE
„
NOTE
The fluorescent light used in the LCD monitor may have to be periodically replaced.
For the warranty coverage on this component, please check with local iiyama
service center.
If you have to return your unit for service and the original packaging has been
discarded, please contact your dealer or iiyama service center for advice or
replacement packaging.
„
CLEANING
WARNING
CAUTION
NOTE
If you drop any materials or liquids such as water into the monitor when cleaning,
unplug the power cable immediately and contact your dealer or iiyama service center.
„
„ For safety reasons, turn off the power switch and unplug the monitor before you
clean it.
„ To protect the LCD panel, do not scratch or rub the screen with a hard object.
„ Never use any of the following strong solvents. These will damage the cabinet and
the LCD screen.
Spray-type cleaner
Wax
Thinner
Benzine
Acid or Alkaline solvent
Abrasive cleaner
Touching the cabinet with any product made from rubber or plastic for a long time
may cause degeneration or loss of paint on the cabinet.
„
Stains can be removed with a cloth lightly moistened with a mild detergent solvent. Then
wipe the cabinet with a soft dry cloth.
CABINET
LCD
Periodic cleaning with a soft dry cloth is recommended.
SCREEN
Don't use tissue paper etc. because these will damage the LCD screen.
FOR YOUR SAFETY
3
PLE2001_3WS_WSV-e-M034B01.P65
7
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU OPERATE THE MONITOR
FEATURES
‹ 51.1cm (20.1") TFT Color LCD Monitor
‹ Supports Resolutions up to 1680 × 1050
‹ High Contrast 1000:1 / Quick Response Time 5ms : ProLite E2001
‹ High Contrast 2000:1 (DCR) / Quick Response Time 2ms (Gray to Gray) :
ProLite E2003
‹ Digital Character Smoothing
‹ Automatic Set-up
‹ Stereo Speakers
2 × 1W Stereo Speakers
‹ Plug & Play VESA DDC2B Compliant
Windows® 95/98/2000/Me/XP/Vista Compliant
‹ Power Management (ENERGY STAR® VESA DPMS Compliant)
‹ Ergonomic Design: TCO ’03 and MPR 3 Approved
‹ Digital Input (DVI-D, HDCP Compliant) for Clear Display :
ProLite E2001WS / E2003WS
‹ VESA Mounting Standard (100mm×100mm) Compliant
CHEKING THE CONTENTS OF THE PACKAGE
The following accessories are included in your package. Check to see if they are enclosed with the
monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama
office.
„ Power Cable*1
„ Audio Cable
„ D-Sub Signal Cable
„ Stand
„ DVI-D Signal Cable*2
„ User Manual
*1 The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using
a power supply higher than this rating, then a power cable with a rating of 10A/
250V must be used.However, all guarantees and warranties are void for any
problems or damage caused by a power cable not supplied by iiyama.
*2 Accessory for ProLite E2001WS / E2003WS
CAUTION
4
BEFORE YOU OPERATE THE MONITOR
PLE2001_3WS_WSV-e-M034B01.P65
8
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE STAND
The monitor is shipped with the stand detached. Be sure to attach the stand before operating the
display and remove if it is necessary to re-box.
Install the Stand on a stable surface. The monitor may cause injury or damage if
it falls or is dropped.
CAUTION
„
Do not give a strong impact to the monitor. It may cause damage.
„
„
Unplug the monitor before installation to avoid electric shock or damage.
<Installation>
1. Put a piece of soft cloth on the table
beforehand to prevent the monitor from being
scratched. Lay the monitor flat on a table with
front face down.
2. The Stand-Bottom is pulled up as shown in
the figure.
3. Install the Stand-Base to the Stand-Bottom.
<Remove>
1. Put a piece of soft cloth on the table
beforehand to prevent the monitor from being
scratched. Lay the monitor flat on a table with
front face down.
2. Hold down the hooks outside and pull the
Stand-Base away from the Stand-Bottom.
BEFORE YOU OPERATE THE MONITOR
5
PLE2001_3WS_WSV-e-M034B01.P65
9
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS AND CONNECTORS
AUTO
EXIT
ENTER
<Back>
<Front>
A Auto Button (AUTO)
B Exit / Volume Button (EXIT)
C Scroll Down / Contrast Button (
D Scroll Up / Brightness Button (
E Menu / Select Button (ENTER)
)
)
F Power Switch (
)
G Headphone Connector
Power Indicator
H
Green: Normal operation
NOTE
Orange: Power Management
The monitor enters into power management mode which reduces the power
consumption to less than 2W when receiving no horizontal and/or vertical
sync signal.
Speakers
I
J
Audio Connector (LINE IN)
K AC Connector (POWER IN)
L DVI-D 24pin Connector (DVI) *
M D-SUB mini 15pin Connector (D-SUB)
N Keyhole for Security Lock
You can fasten a security lock and cable to prevent the monitor from being removed
without your permission.
NOTE
* Available for ProLite E2001WS / E2003WS only.
6
BEFORE YOU OPERATE THE MONITOR
PLE2001_3WS_WSV-e-M034B01.P65
10
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING YOUR MONITOR
Ensure that both the computer and the monitor are switched off.
A
B
Connect the computer to the monitor with the signal cable.(See page 25 for CONNECTOR PIN
ASSIGNMENT.)
Connect the monitor to the audio equipment with the Audio Cable for computer when using the
audio features.
C
Connect the Power Cable to the monitor first and then to the power supply.
D
NOTE „ The signal cables used for connecting the computer and monitor may vary with the type of
computer used. An incorrect connection may cause serious damage to both the monitor and
the computer. The cable supplied with the monitor is for a standard 15 pin D-Sub connector.
If a special cable is required please contact your local iiyama dealer or regional iiyama office.
„ For connection to Macintosh computers, contact your local iiyama dealer or regional
iiyama office for a suitable adaptor.
„ Make sure you tighten the finger screws at each end of the signal cable.
[Example of Connection]
<Back>
Power Cable
(Accessory)
D-Sub Signal Cable
(Accessory)
DVI-D Signal Cable
(Accessory) *
Audio Cable (Accessory)
Computer
* Available for ProLite E2001WS / E2003WS only.
BEFORE YOU OPERATE THE MONITOR
7
PLE2001_3WS_WSV-e-M034B01.P65
11
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER SETTING
„ Signal Timing
Change to the desired signal timing listed on page 24: COMPLIANT TIMING.
„ Windows 95/98/2000/Me/XP/Vista Plug & Play
The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on
Windows 95/98/2000/Me/XP/Vista by connecting the monitor to DDC2B compliant computer with
the Signal Cable supplied.
For installation on Windows 95/98/2000/Me/XP: The monitor Information File for iiyama monitors
may be necessary for your computer and obtained via the Internet, using the address:
NOTE
„ For additional information on how to download the driver for your touch screen monitor,
please access the internet site noted above.
„ Monitor Drivers are not required in most cases for Windows Vista, Macintosh or Unix
operating systems. For further information, please contact your computer dealer first
for advice.
ADJUSTING THE VIEWING ANGLE
„ For optimal viewing it is recommended to look at the full face
of the monitor.
„ Hold the stand so that the monitor does not topple when you
change the monitor’s angle.
„ You are able to adjust the monitor’s angle up to 22 degrees
upward, 2 degrees downward.
„ In order to ensure a healthy and relaxed body position when
using the monitor at visual display workstations, it is
recommended that the adjusted tilt angle should not exceed
10 degrees. Adjust the monitor’s angle to your own preference.
NOTE
NOTE
„ Do not touch the LCD screen when you change the
angle. It may cause damage or break the LCD screen.
„ Careful attention is required not to catch your fingers
or hands when you change the angle.
„ Do not tilt the post beyond 20 degrees except when
repacking the monitor in its box.
To do so may cause the monitor to fall over and break.
8
BEFORE YOU OPERATE THE MONITOR
PLE2001_3WS_WSV-e-M034B01.P65
12
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE MONITOR
To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT
TIMING shown on page 24. You are also able to adjust the picture by following the button operation
shown below. For more detailed adjustments, see page 14 for SCREEN ADJUSTMENTS.
Press the ENTER Button to start the On Screen Display feature. There are
additional Menu items which can be switched by using the
/
Buttons.
Main Menu
Auto Adjust
Luminance
Geometry
Color
Language
Recall
Miscellaneous
Input Select
Audio
OSD
Select the Menu item which contains the adjustment icon relating to the
B
C
adjustment you want to make. Press the ENTER Button. Then, use the
Buttons to highlight the desired adjustment icon.
/
Press the ENTER Button again. Use the
adjustment or setting.
/
Buttons to make the appropriate
D Press the EXIT Button to leave the menu, and the settings you just made would
be automatically saved.
For example, to correct for vertical position, select Menu item of Geometry and then press the
ENTER Button. Then, select
(V.Position) by using the
/
Buttons.
Main Menu
Geometry
Auto Adjust
Luminance
Geometry
Color
Language
Recall
H. Position
V. Position
Pixel Clock
Phase
50
50
50
50
Miscellaneous
Input Select
Audio
OSD
An adjustment page appears after you press the ENTER Button. Then, use the
/
Buttons to
change the vertical position settings. The vertical position of the overall display should be
changing accordingly while you are doing this.
Press the EXIT Button lastly, it ends, any changes are saved in the memory.
Geometry
V. Position
50
NOTE
„
When button operations are aborted during adjustment, On-Screen Display disappears when the
time set for the OSD Time has passed. Also, press the EXIT button to quickly turn off the On-
Screen Display.
Any changes are automatically saved in the memory when the On Screen Display disappears.
„
„
Turning off the power should be avoided while using the Menu.
ADJUSTING
Adjustments for H. / V. Position, Pixel Clock and Phase are saved for each signal timing. Except for
these adjustments, all other adjustments have only one setting which applies to all signal timings.
OPERATING THE MONITOR
9
PLE2001_3WS_WSV-e-M034B01.P65
13
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENT MENU CONTENTS
Auto Adjust
Only Analog Input
Adjustment Item
Auto Adjust *
Problem / Option
Button to Press
Adjust H. / V. Position, Pixel Clock and Phase automatically.
Direct
*
For best results, use the Auto Adjust in conjunction with the adjustment pattern. See page 14 for
SCREENADJUSTMENTS.
Direct
You can skip the Menu items and display an adjustment scale directly by using the following
button operations.
z Auto Adjust: Press the Auto Button when the Menu is not displayed.
Luminance *1
Adjustment Item
Brightness *2
Problem / Option
Too dark
Button to Press
Direct
Direct
Too bright
Too dull
Contrast
Too intense
1
*
Luminance adjustment disabled when DCR mode is active.
2
*
Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too
bright.
Direct
You can skip the Menu items and display an adjustment scale directly by using the following
button operations.
z Contrast:
Press the
Button when the Menu is not displayed.
Button when the Menu is not displayed.
z Brightness: Press the
10 OPERATING THE MONITOR
PLE2001_3WS_WSV-e-M034B01.P65
14
2007/10/01, 18:12
Download from Www.Somanuals.com. All Manuals Search And Download.
Geometry
Only Analog Input
Adjustment Item
Problem / Option
Button to Press
Too left
H. Position
V. Position
Pixel Clock
Phase
Too right
Too low
Too high
Too narrow
Too wide
To correct flickering text or lines
Color
Adjustment Item
Problem / Option
Bluish white
Button to Press
9300K
7500K
6500K
Yellowish white
Reddish white
Red
Too weak
User Preset
Green
Too strong
Blue
OSD
Adjustment Item
Problem / Option
Button to Press
OSD is too left
OSD is too right
H.Position
OSD is too low
OSD is too high
V.Position
OSD Time
You can set the OSD display duration time
between 5 and 30 seconds.
OPERATING THE MONITOR 11
PLE2001_3WS_WSV-e-M034B01.P65
15
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
Language
Adjustment Item
Problem / Option
Button to Press
Spanish
Español
English
Français
Deutsch
Italiano
Polski
English
French
German
Italian
Nederlands Dutch
Japanese
Language
Simplified Chinese
Russian
Polish
Recall
Adjustment Item
Recall All
Problem / Option
Button to Press
Factory-preset data is restored.
Return to Menu.
Yes
No
Miscellaneous
Adjustment Item
Problem / Option
Button to Press
1 2 3 4 5
Sharpness
You can change the picture quality from 1 to 5 (sharp to soft).
Press the Button to change the picture quality in numerical
order. Press the Button to change the picture quality in reverse
numerical order.
On
DDC/CI is turned ON.
DDC/CI is turned OFF.
DDC/CI
Off
DDC/CI On and Off are switched as follows by pressing the Button successively.
On Off
NOTE
Displays information regarding the current input signal coming
from the graphic card in your computer.
Miscellaneous
Display Information
Display Information
1680x1050
@
60 Hz
See your graphic card user guide for more information
about changing the resolution and refresh.
NOTE
12 OPERATING THE MONITOR
PLE2001_3WS_WSV-e-M034B01.P65
16
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
Miscellaneous
Adjustment Item
DCR
Problem / Option
Button to Press
On
Increased Contrast Ratio
Typical Contrast Ratio
Off
0 1 2 3 4 5
OD
You can set the OverDrive level between 0 and 5. It will
improve the gray level response time of the LCD panel. A
higher level results in a faster response time.
Input Select
Available for ProLite E2001WS / E2003WS only.
Adjustment Item
Input Select
Problem / Option
Button to Press
D-sub
DVI
Select the Analog input.
Select the Digital input.
When only one of the two signal inputs is connected to the signal source, the one
connected is automatically selected. Input Select function is not available if there is no
signal input from the selected connector or during the power management mode.
NOTE
Audio
Adjustment Item
Problem / Option
Too soft
Button to Press
Direct
Volume
Mute
Too loud
On
Turn off the sound temporarily.
Return the sound volume to the previous level.
Button successively.
Off
„ Mute On and Off are switched as follows by pressing the
On Off
NOTE
Direct
You can skip the Menu items and display an adjustment scale directly by using the following
button operations.
z Volume: Press the Exit Button when the Menu is not displayed.
OPERATING THE MONITOR 13
PLE2001_3WS_WSV-e-M034B01.P65
17
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
SCREEN ADJUSTMENTS
Adjust the image by following the procedure below to get the desired picture when selecting Analog input.
„ The screen adjustments described in this manual are designed to set image position and minimize
flicker or blur for the particular computer in use.
„ The monitor is designed to provide the best performance at resolution of 1680 × 1050, but can not
provide the best at resolutions of less than 1680 × 1050 because the picture is automatically stretched
to fit the full screen. It is recommended to operate at resolution of 1680 × 1050 in normal use.
„ Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to
the screen enlargement process.
„ It is preferable to adjust the image position and frequency with the monitor controls, rather than the
computer software or utilities.
„ Perform adjustments after a warm-up period of at least thirty minutes.
„ Additional adjustments may be required after the Auto Adjust depending on the resolution or signal
timing.
„ The Auto Adjust may not work correctly when displaying the picture other than the screen
adjustment pattern. In this case, manual adjustments are required.
There are two ways to adjust the screen. One way is automatic adjustment for Position, Pixel Clock
and Phase. The other way is performing each adjustment manually.
Perform the Auto Adjust first when the monitor is connected to a new computer, or resolution is
changed. If the screen has a flicker or blur, or the picture does not fit in the display area after
performing the Auto Adjust, manual adjustments are required. Both adjustments should be made by
using the screen adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://
www.iiyama.com).
Adjust the image by following the procedure below to get the desired picture.
This manual explains adjustment under Windows 95/98/2000/Me/XP.
Display the picture at the optimum resolution.
A
B
Enter the Test.bmp (screen adjustment pattern) to wallpaper.
NOTE
„ Consult the appropriate documentation for doing this.
„ Test.bmp is made at resolution of 1280 × 1024. Set the display position to center in the
wallpaper setting dialogue box. If you use Microsoft® PLUS! 95/98 cancel the setting
of “Stretch desktop wallpaper to fit the screen”.
[Adjustment pattern]
Color bar
Zebra pattern
Picture frame
14 OPERATING THE MONITOR
PLE2001_3WS_WSV-e-M034B01.P65
18
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the Auto Button. (Auto Adjust)
C
D
Adjust the image manually by following procedure below when the screen has a
flicker or blur, or the picture does not fit in the display area after performing the Auto
Adjust.
Adjust the V.Position so that the top and bottom of the picture frame will fit to the
display area.
E
1) Adjust the H.Position so that the left side of the picture frame will move to the left
edge of the display area.
F
2) Stretch the right side of the picture frame to the right edge of the display area by
adjusting the Pixel Clock.
„ When the left side of the picture frame moves apart from the left edge of the display
NOTE
area during the Pixel Clock adjustment, adjust steps 1) and 2).
„ Another way to make the Pixel Clock adjustment is to correct the vertical wavy lines
in the zebra pattern.
„ The picture may flicker during the Pixel Clock, H.Position and V.Position adjustment.
„ In case the picture frame is bigger or smaller than the data display area after the Pixel
Clock adjustment, repeat steps from
.
C
1
OPERATING THE MONITOR 15
PLE2001_3WS_WSV-e-M034B01.P65
19
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust the Phase to correct horizontal wavy noise, flicker or blur in the zebra pattern.
G
„ In case the strong flicker or blurs remain on a part of the screen, repeat steps
NOTE
and
F
because the Pixel Clock may not be adjusted correctly. If the flicker or blurs still
G
remain, set the refresh rate of computer to low (60Hz) and repeat steps from
again.
C
„ Adjust the H.Position after the Phase adjustment if the horizontal position moves
during the adjustment.
Adjust the Brightness and Color to get the desired picture after you complete the
Pixel Clock and Phase adjustments.
H
Put back your favorite wallpaper.
16 OPERATING THE MONITOR
PLE2001_3WS_WSV-e-M034B01.P65
20
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER MANAGEMENT FEATURE
The power management feature of this product complies with power saving requirement of ENERGY
STAR® and VESA DPMS. When activated, it automatically reduces unnecessary power consumption
of the monitor when your computer is not in use.
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There
is a power management step the monitor takes as described below. The power management function,
including any timer settings is configured by the operating system. Check your operating system
manual for information on how this can be configured.
„ Power Management Mode
When the H-sync signal / V-sync signal / H and V sync signals from the computer are off, the
monitor enters into Power Management Mode which reduces the power consumption to less than
2W. The screen becomes dark, and the power indicator turns to orange. From Power Management
Mode, the image reappears in several seconds when either the keyboard or the mouse are
touched again.
Power Indicator
NORMAL MODE
Green
POWER MANAGEMENT MODE
Orange
POWER
0
2W
100%
CONSUMPTION
Even when using the power management mode, the monitor consumes electricity. Turn
off the Power Switch whenever the monitor is not in use, during the night and weekends,
to avoid unnecessary power consumption.
NOTE
„
„
It is possible that the video signal from the computer may be on while the H or V sync
signal is missing. In this instance, the POWER MANAGEMENT feature may not work
properly.
OPERATING THE MONITOR 17
PLE2001_3WS_WSV-e-M034B01.P65
21
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
If the monitor fails to operate correctly, please follow the steps below for a possible solution.
1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you
have. If the monitor does not get a picture, skip to 2.
2. Consult the following items if you cannot find an appropriate adjustment item in OPERATING THE
MONITOR or if the problem persists.
3.
If you are experiencing a problem which is not described below or you cannot correct the
problem, discontinue using the monitor and contact your dealer or iiyama service center for
further assistance.
Problem
Check
The picture does
not appear.
A
(Power indicator
does not light up.)
† The Power Cable is firmly seated in the socket.
† The Power Switch is turned ON.
† The AC socket is live. Please check with another piece of equipment.
(Power indicator
is green.)
† If the blank screen saver is in active mode, touch the keyboard or the
mouse.
† Increase the Contrast and/or Brightness.
The computer is ON.
†
† The Signal Cable is properly connected.
† The signal timing of the computer is within the specification of the monitor.
(Power indicator † If the monitor is in power management mode, touch the keyboard or the
is orange.)
mouse.
The computer is ON.
†
† The Signal Cable is properly connected.
†
The signal timing of the computer is within the specification of the monitor.
The screen is not † The Signal Cable is properly connected.
B
synchronized.
† The signal timing of the computer is within the specification of the monitor.
† The video output level of the computer is within the specification of the
monitor.
The screen
position is not in
the center.
† The signal timing of the computer is within the specification of the monitor.
C
D
E
The screen is
too bright or too
dark.
† The video output level of the computer is within the specification of the
monitor.
† The power voltage is within the specification of the monitor.
The screen is
shaking.
†
The signal timing of the computer is within the specification of the monitor.
18 TROUBLE SHOOTING
PLE2001_3WS_WSV-e-M034B01.P65
22
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
No sound.
Check
† The audio equipment (computer etc.) is ON.
† The Audio Cable is properly connected.
† The Volume is turned up.
F
† The Mute is OFF.
† The audio output level of the audio equipment is within the specification of
the monitor.
The sound is too † The audio output level of the audio equipment is within the specification of
G
H
loud or too quiet.
the monitor.
A strange noise is † The Audio Cable is properly connected.
heard.
RECYCLING INFORMATION
For better environment protection please don't dispose your monitor.
TROUBLESHOOTING 19
PLE2001_3WS_WSV-e-M034B01.P65
23
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
SPECIFICATIONS
ProLite E2001WS
LCD Panel Driving system
Size
a-Si TFT Active Matrix
Diagonal: 51.1cm / 20.1"
0.258mm H × 0.258mm V
250cd/m2 (Typical)
Pixel pitch
Brightness
Contrast ratio
1000 : 1 (Typical)
Viewable angle Right / Left / Up / Down: 80 degrees each (Typical)
Response time 5ms (Black, white, black)
Display Colors
Approx.16.2M (6bit+FRC dithering)
Horizontal: 31.0-83.0kHz, Vertical: 56-75Hz
165MHz maximum
Sync Frequency
Dot Clock
Maximum Resolution
Input Connector
Plug & Play
1680 × 1050, 1.8 MegaPixels
D-Sub mini 15 pin, DVI-D 24 pin
VESA DDC2BTM
Input Sync Signal
Separate sync: TTL, Positive or Negative
Analog: 0.7Vp-p (Standard), 75Ω, Positive
Input Video Signal
Digital: DVI(Digital Visual Interface standard Rev.1.0)compliance
Input Audio Connector
Input Audio Signal
Speakers
ø 3.5mm mini jack (Stereo)
0.5Vrms maximum
1W × 2 (Stereo speakers)
Maximum Screen Size
Power Source
433.4mm W × 270.9mm H / 17.1" W × 10.7" H
100-240VAC, 50/60Hz, 1.3A
Power Consumption
Dimensions / Net Weight
Tilt Angle
49W maximum, Power management mode: 2W maximum*
480.0× 399.0 × 188.0mm / 18.9 ×15.7 × 7.4" (W×H×D), 4.4kg / 9.7lbs
Up: 22 degrees, Down: 2 degrees
Operating: Temperature
Humidity
5 to 35°C / 41 to 95°F
10 to 80% (No condensation)
Environmental
Considerations
Storage: Temperature -20 to 60°C / -4 to 140°F
10 to 70% (No condensation)
Humidity
Approvals
TCO ’03, CE, TÜV-GS / MPR3 (prEN50279) / ISO 13406-2,
FCC-B, UL/ C-UL, VCCI-B, GOST-R
NOTE * Condition: Audio equipment is not connected.
20 APPENDIX
PLE2001_3WS_WSV-e-M034B01.P65
24
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
ProLite E2001WSV
LCD Panel Driving system
Size
a-Si TFT Active Matrix
Diagonal: 51.1cm / 20.1"
0.258mm H × 0.258mm V
250cd/m2 (Typical)
Pixel pitch
Brightness
Contrast ratio
1000 : 1 (Typical)
Viewable angle Right / Left / Up / Down: 80 degrees each (Typical)
Response time 5ms (Black, white, black)
Display Colors
Approx.16.2M (6bit+FRC dithering)
Horizontal: 31.0-83.0kHz, Vertical: 56-75Hz
165MHz maximum
Sync Frequency
Dot Clock
Maximum Resolution
Input Connector
Plug & Play
1680 × 1050, 1.8 MegaPixels
D-Sub mini 15 pin
VESA DDC2BTM
Input Sync Signal
Separate sync: TTL, Positive or Negative
Analog: 0.7Vp-p (Standard), 75Ω, Positive
ø 3.5mm mini jack (Stereo)
Input Video Signal
Input Audio Connector
Input Audio Signal
Speakers
0.5Vrms maximum
1W × 2 (Stereo speakers)
Maximum Screen Size
Power Source
433.4mm W × 270.9mm H / 17.1" W × 10.7" H
100-240VAC, 50/60Hz, 1.3A
Power Consumption
Dimensions / Net Weight
Tilt Angle
49W maximum, Power management mode: 2W maximum*
480.0× 399.0 × 188.0mm / 18.9 ×15.7 × 7.4" (W×H×D), 4.4kg / 9.7lbs
Up: 22 degrees, Down: 2 degrees
Operating: Temperature
Humidity
5 to 35°C / 41 to 95°F
10 to 80% (No condensation)
Environmental
Considerations
Storage: Temperature -20 to 60°C / -4 to 140°F
Humidity
10 to 70% (No condensation)
Approvals
TCO ’03, CE, TÜV-GS / MPR3 (prEN50279) / ISO 13406-2,
FCC-B, UL/ C-UL, VCCI-B, GOST-R
NOTE * Condition: Audio equipment is not connected.
APPENDIX 21
PLE2001_3WS_WSV-e-M034B01.P65
25
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
ProLite E2003WS
LCD Panel Driving system
Size
a-Si TFT Active Matrix
Diagonal: 51.1cm / 20.1"
0.258mm H × 0.258mm V
300cd/m2 (Typical)
Pixel pitch
Brightness
Contrast ratio
1000 : 1 (Typical), 2000 : 1 (DCR)
Viewable angle Right / Left / Up / Down: 85 degrees each (Typical)
Response time 5ms (Typical), 2ms (Gray to Gray)
Display Colors
Approx.16.7M
Sync Frequency
Dot Clock
Horizontal: 31.0-83.0kHz, Vertical: 56-75Hz
165MHz maximum
Maximum Resolution
Input Connector
Plug & Play
1680 × 1050, 1.8 MegaPixels
D-Sub mini 15 pin, DVI-D 24 pin
VESA DDC2BTM
Input Sync Signal
Separate sync: TTL, Positive or Negative
Analog: 0.7Vp-p (Standard), 75Ω, Positive
Input Video Signal
Digital: DVI(Digital Visual Interface standard Rev.1.0)compliance
Input Audio Connector
Input Audio Signal
Speakers
ø 3.5mm mini jack (Stereo)
0.5Vrms maximum
1W × 2 (Stereo speakers)
Maximum Screen Size
Power Source
433.4mm W × 270.9mm H / 17.1" W × 10.7" H
100-240VAC, 50/60Hz, 1.3A
Power Consumption
Dimensions / Net Weight
Tilt Angle
49W maximum, Power management mode: 2W maximum*
480.0× 399.0 × 188.0mm / 18.9 ×15.7 × 7.4" (W×H×D), 4.4kg / 9.7lbs
Up: 22 degrees, Down: 2 degrees
Operating: Temperature
Humidity
5 to 35°C / 41 to 95°F
10 to 80% (No condensation)
Environmental
Considerations
Storage: Temperature -20 to 60°C / -4 to 140°F
10 to 70% (No condensation)
Humidity
Approvals
TCO ’03, CE, TÜV-GS / MPR3 (prEN50279) / ISO 13406-2,
FCC-B, UL/ C-UL, VCCI-B, GOST-R
NOTE * Condition: Audio equipment is not connected.
22 APPENDIX
PLE2001_3WS_WSV-e-M034B01.P65
26
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
ProLite E2003WSV
LCD Panel Driving system
Size
a-Si TFT Active Matrix
Diagonal: 51.1cm / 20.1"
0.258mm H × 0.258mm V
300cd/m2 (Typical)
Pixel pitch
Brightness
Contrast ratio
1000 : 1 (Typical), 2000 : 1 (DCR)
Viewable angle Right / Left / Up / Down: 85 degrees each (Typical)
Response time 5ms (Typical), 2ms (Gray to Gray)
Display Colors
Approx.16.7M
Sync Frequency
Dot Clock
Horizontal: 31.0-83.0kHz, Vertical: 56-75Hz
165MHz maximum
Maximum Resolution
Input Connector
Plug & Play
1680 × 1050, 1.8 MegaPixels
D-Sub mini 15 pin
VESA DDC2BTM
Input Sync Signal
Separate sync: TTL, Positive or Negative
Analog: 0.7Vp-p (Standard), 75Ω, Positive
ø 3.5mm mini jack (Stereo)
Input Video Signal
Input Audio Connector
Input Audio Signal
Speakers
0.5Vrms maximum
1W × 2 (Stereo speakers)
Maximum Screen Size
Power Source
433.4mm W × 270.9mm H / 17.1" W × 10.7" H
100-240VAC, 50/60Hz, 1.3A
Power Consumption
Dimensions / Net Weight
Tilt Angle
49W maximum, Power management mode: 2W maximum*
480.0× 399.0 × 188.0mm / 18.9 ×15.7 × 7.4" (W×H×D), 4.4kg / 9.7lbs
Up: 22 degrees, Down: 2 degrees
Operating: Temperature
Humidity
5 to 35°C / 41 to 95°F
10 to 80% (No condensation)
Environmental
Considerations
Storage: Temperature -20 to 60°C / -4 to 140°F
Humidity
10 to 70% (No condensation)
Approvals
TCO ’03, CE, TÜV-GS / MPR3 (prEN50279) / ISO 13406-2,
FCC-B, UL/ C-UL, VCCI-B, GOST-R
NOTE * Condition: Audio equipment is not connected.
APPENDIX 23
PLE2001_3WS_WSV-e-M034B01.P65
27
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSIONS
DIMENSIONS
480.0mm/18.9"
58.0mm/2.3"
436.0mm/17.2"
226.0mm/8.9"
COMPLIANT TIMING
Vertical
Frequency
Horizontal
Frequency
Video Mode
Dot Clock
31.468kHz
37.500kHz
37.878kHz
46.875kHz
48.362kHz
60.024kHz
47.396kHz
60.000kHz
63.979kHz
79.974kHz
55.935kHz
65.290kHz
31.468kHz
49.724kHz
68.680kHz
59.941Hz
74.997Hz
60.317Hz
75.001Hz
60.002Hz
75.039Hz
60.000Hz
60.000Hz
60.029Hz
75.024Hz
59.887Hz
60.000Hz
70.086Hz
74.532Hz
75.060Hz
25.175MHz
31.500MHz
40.000MHz
49.500MHz
65.000MHz
78.750MHz
68.250MHz
108.000MHz
108.000MHz
135.000MHz
106.500MHz
146.250MHz
28.322MHz
57.280MHz
100.000MHz
VGA
SVGA
XGA
640 × 480
800 × 600
1024 × 768
WXGA
1280 × 768
1280 × 960
VESA
Quad-VGA
SXGA 1280 × 1024
WXGA+ 1440 × 900
WSXGA+1680 × 1050
720 × 400
*
*
*
VGA TEXT
Macintosh
832 × 624
1152 × 870
NOTE
* DVI input is not compliant.
24 APPENDIX
PLE2001_3WS_WSV-e-M034B01.P65
28
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTOR PIN ASSIGNMENT
„
D-Sub mini 15pin
Connector
Pin
1
Input Signal
Red video
Pin
9
Input Signal
+5V
2
10 Ground
Green video
Blue video
11
12
NC
Data line (SDA)*
3
4
NC
5
Ground
13 H-Sync
6
Red video ground
Green video ground
Blue video ground
V-Sync
14
15
7
Clock line (SCL)*
8
* Compliant to VESA DDC.
„ DVI-D 24pin
Pin
1
Input Signal
T.M.D.S Data 2–
T.M.D.S Data 2+
Pin
13
14
15
Input Signal
Connector *1
+5V
2
1
9
8
16
24
3
T.M.D.S Data 2 Ground
Ground
17
4
16 Hot Plug Detect
17 T.M.D.S Data 0–
18 T.M.D.S Data 0+
19 T.M.D.S Data 0 Ground
20
DVI-D
5
6
Clock line (SCL) *2
Data line (SDA) *2
V-Sync
7
8
9
T.M.D.S Data 1–
T.M.D.S Data 1+
21
10
11
12
22 T.M.D.S Clock Ground
23 T.M.D.S Clock +
T.M.D.S Data 1 Ground
T.M.D.S Clock –
24
*2 Compliant to VESA DDC.
*1 Available for ProLite E2001WS / E2003WS only.
APPENDIX 25
M034B01
PLE2001_3WS_WSV-e-M034B01.P65
29
2007/09/10, 18:19
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|