INSTRUCTION MANUAL
VHF P25 TRUNKING
MOBILE TRANSCEIVER
iF9511HT
This device complies with Part 15 of the FCC Rules. Op-
eration is subject to the condition that this device does
not cause harmful interference.
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC INFORMATION
ABOUT IPR
This device is made under license under one or more of the
following U.S. Patents: #4,590,473; #4,636,791; #5,148,482;
#5,185,796;#5,271,017;#5,377,229;#4,716,407;#4,972,460;
#5,502,767;#5,146,497;#5,164,986;#5,185,795;#5,164,986,
#5,185,795, and #5,146,497.
• FOR CLASS B UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential instal-
lation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
* IPR means ‘Intellectual Property Rights.’
VOICE CODING TECHNOLOGY
The AMBE+2™ voice coding Technology embodied in this
product is protected by intellectual property rights including
patent rights, copyrights and trade secrets of Digital Voice
Systems, Inc. This voice coding Technology is licensed sole-
ly for use within this Communications Equipment. The user
of this Technology is explicitly prohibited from attempting to
extract, remove, decompile, reverse engineer, or disassemble
the Object Code, or in any other way convert the Object Code
into a human-readable form. U.S. Patent Nos.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
#5,870,405,#5,826,222,#5,754,974,#5,701,390,#5,715,365,
#5,649,050,#5,630,011,#5,581,656,#5,517,511,#5,491,772,
#5,247,579, #5,226,084 and #5,195,166.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
DO NOT operate the transceiver without running the ve-
hicle’s engine. The vehicle’s battery will quickly run out if the
transceiver transmits while the vehicle’s engine OFF.
RWARNING! NEVER connect the transceiver to an AC
outlet. This may pose a fire hazard or result in an electric shock.
RWARNING! NEVER connect the transceiver to a
power source of more than 16 V DC or use reverse polarity.
This could cause a fire or damage the transceiver.
DO NOT place the transceiver against walls. This will ob-
struct heat dissipation.
DO NOT use harsh solvents such as benzine or alcohol
RWARNING! NEVER cut the DC power cable be-
tween the DC plug and fuse holder. If an incorrect connection
is made after cutting, the transceiver may be damaged.
when cleaning, as they damage the transceiver surfaces.
BE CAREFUL! The transceiver will become hot when
operating continuously for long periods.
CAUTION: NEVER place the transceiver where normal
operation of the vehicle may be hindered or where it could
cause bodily injury.
KEEP the transceiver away from heavy rain, and never im-
merse it in the water.
When the supplied/optional microphone*, the front/rear
plate(s) and the speaker jack cover of the controller are at-
tached, the main unit and the controller meet IP54 require-
ments for dust-protection and splash resistance.
However, once these items have been dropped, dust-protec-
tion and splash resistance cannot be guaranteed because of
possible damage to these cases or the waterproof seal.
* The microphone is not dust-protection and splash resistance.
CAUTION: NEVER allow children to touch the trans-
ceiver.
CAUTION: NEVER expose the transceiver to rain,
snow or any liquids. The transceiver may be damaged.
USE the specified microphone only. Other microphones have
different pin assignments and may damage the transceiver.
DO NOT use or place the transceiver in areas with tem-
peratures below –30°C (–22°F) or above +60°C (+140°F), or
in areas subject to direct sunlight, such as the dashboard.
For U.S.A. only
CAUTION: Changes or modifications to this transceiver,
not expressly approved by Icom Inc., could void your author-
ity to operate this transceiver under FCC regulations.
DO NOT place the transceiver in excessively dusty envi-
ronments.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
TABLE OF CONTENTS
3
4
5
6
7
8
9
10
11
12
13
14
15
16
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL DESCRIPTION
1
n Front panel— Controller
q
w
e
01 ch-01
IC-F9511HT
!
o
i
u y t
r
qAF VOLUME CONTROL KNOB
r10-KEYPAD
Rotate the knob to adjust the audio output level.
• Minimum audio level is pre-programmed.
The keypad allows you to enter digits to:
• Select memory channels, tone channels and DTMF codes (when
in the DTMF code channel selection mode)
• Start up with a password
• Input the Individual ID code during P25 mode operation. (De-
pending on the pre-setting)
wFUNCTION DISPLAY (p. 3)
Displays a variety of information, such as an operating
channel number/name, DTMF numbers and audible con-
dition, etc.
tBUSY INDICATOR
Lights green while receiving a signal, or when the squelch
is open.
eUP/DOWN KEYS
Push to select an operating channel, etc.
*The desired function can be assigned by your dealer. (p. 4)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL DESCRIPTION
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
yPOWER SWITCH [POWER]
Push to turn the power ON and OFF.
• The following functions are available at power ON as options:
- Automatic scan start
NEVER connect non-specified microphones. The pin
assignments may be different and the transceiver may
be damaged.
- Password prompt
- Set mode
D MICROPHONE
The supplied microphone has a PTT switch and a hanger
hook.
uTRANSMIT INDICATOR
• The following functions are available when the microphone is on
or off hook (depending on the setting):
- Automatic scan starts when it is on hook.
- Scan is cancelled when it is off hook.
- Scan is paused when it is off hook.
Automatic priority channel selection is available when it is off hook.
- Sets to ‘Inaudible’ condition (mute condition) when it is on hook.
Sets to ‘Audible’ condition (unmute condition) when it is off hook.
Lights red while transmitting.
iDEALER-PROGRAMMABLE KEYS
Desired functions can be programmed independently by
your dealer. (p. 4)
-
In this instruction manual, these keys are from the left,
called [P0]/[P1]/[P2]/[P3]/[P4].
-
!SPEAKER JACK
oMICROPHONE CONNECTOR
Connect a 4–8 ø external speaker.
• Max. input power: 7 W
• Attach the jack cover when no external speaker is connected.
Connect the supplied or optional microphone.
• When you connect a microphone, be sure to fit the connector
cover of the microphone into the connector to maintain the con-
troller’s dust protection and splash resistance.
Jack cover
Connector cover
2
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL DESCRIPTION
1
n Function display— Controller
q
w
e
r
t
y
u
i
yBELL INDICATOR
Appears/blinks when a matched signal is received, de-
pending on the pre-programming.
01 ch-01
Ic-F9511HT
o
uTELEPHONE INDICATOR
Appears when a phone call* is received.
* P25 operation only
!
iSHORT MESSAGE INDICATOR
Appears when an Status message or Short message is
received.
qRECEIVED SIGNAL STRENGTH INDICATOR
Indicates relative signal strength level.
oALPHANUMERIC DISPLAY
Displays an operating channel number, channel name, Set
Weak Receive Signal level Strong
mode contents, DTMF code, etc.
wLOW POWER INDICATOR
!ACTIVATED KEY INDICATOR
Appears when low output power is selected.
• When high output power is selected, no indicator appears.
Appears above the key assigned as [Scan Add/Del (Tag)]
key when that key has been activated.
eAUDIBLE INDICATOR
Appears when the channel is in the ‘Audible’ (unmute) con-
dition.
See the operating guide for details of Analog, MDC and
P25 Trunking/Conventional system operations. Consult
your Icom dealer or system operator for details concern-
ing your transceiver’s programming.
rCOMPANDER INDICATOR
Appears when the compander function* is activated.
* Analog mode operation only
tSCRAMBLER INDICATOR
Appears when the voice scrambler or encryption function
is activated.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL DESCRIPTION
1
1
2
3
4
5
6
7
8
n Programmable function keys
The following functions can be assigned to [UP], [DOWN],
[P0], [P1], [P2], [P3] and [P4] programmable function keys.
Consult your Icom dealer or system operator for details con-
cerning your transceivers programming.
If the programmable function names are bracketed in the fol-
lowing explanations, the specific key is used to activate the
function depends on the programming.
SCAN KEY
➥ Push to start and cancel scanning operation.
• When the Power ON Scan or Auto Scan function starts a scan,
push this key to cancel the scan. The canceled scan resumes
after a specified time period.
➥ Push and hold this key for 1 sec. to indicate a scan group,
then push [CH Up] or [CH Down] to select the desired one.
(Depending on the pre-setting.)
CH UP AND DOWN KEYS
SCAN ADD/DEL (TAG) KEY
➥ Push to add the selected channel to or delete it from the
➥ Push to select an operating channel.
➥ Push to select a scan group after pushing and holding
[Scan].
9
scan group.
1. Push to indicate a scan group, then push [CH Up] or
[CH Down] to select the desired one.
2. Push to add the channel to or delete it from the selected
scan group.
3. Push and hold for 1 sec. to exit the scan group selection
mode.
10
11
12
13
14
15
16
ZONE KEY
Push this key, then push [CH Up] or [CH Down] to select the
desired zone.
What is “zone”?—The desired channels are assigned
into a zone according to the intended use for grouping.
For example, ‘Staff A’ and ‘Staff B’ are assigned into a
“Business” zone, and ‘John’ and ‘Cindy’ are assigned into a
“Private” zone.
➥
While a scan is paused on a non-priority channel, push this
key to delete the selected channel from the scan group.
• Depending on the pre-setting, the deleted channel is added to
the scan group again, after the scan is canceled. (Nuisance De-
lete function)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL DESCRIPTION
1
PRIO A/B KEYS
PUBLIC ADDRESS KEY
➥ Push to select Priority A or Priority B channel.
➥ Push and hold [Prio A (Rewrite)] or [Prio B (Rewrite)] for
1 sec. to assign the operating channel to the Priority A or
Priority B channel.
Push to activate the Public Address (PA) function for voice
amplification. When the PA function is activated, the audio
output can be controlled from the transceiver separately with
[CH Up] or [CH Down].
• This function is available when the external unit, such as an audio
amplifier, speaker, etc. is additionally connected. (p. 16)
• Push this key, then speak into the microphone while pushing and
holding [PTT].
MR-CH 1/2/3/4 KEYS
Push to select the memory channel 1, 2, 3 or 4.
NOTE: “PA/RX Speaker” setting should be turned OFF by
your dealer with the CS-F9010/F9510 c l o n i n g s o f t wa r e
to activate the PA function. Ask your dealer for details.
MONI KEY
➥ Push to mute and release the CTCSS (DTCS), 2-tone,
NAC or Talkgroup ID squelch mute. Open any squelch/de-
activate any mute while pushing this key.
• Depending on the pre-setting, the ‘Audible’ (unmute) condition
may automatically return to the ‘Inaudible’ (mute) condition, after
a specified time period.
RX SPEAKER KEY
Push to turn the RX speaker function ON or OFF.
When the RX speaker function is turned ON, the received
audio can be heard via the external speaker.
• This function is available when the external speaker is additionally
connected. (p. 16)
➥ Depending on the pre-setting, pushing and holding this
key for 1 sec. cancels the scan.
• This function is useful when you are out of the vehicle.
• The audio output level is linked to the transceiver’s volume control.
TALK AROUND KEY (Conventional operation only)
Turn the talk around function ON or OFF.
• The talk around function equalizes the transmit frequency to the
receive frequency for transceiver-to-transceiver communication.
DO NOT operate this key with this transceiver. Otherwise
no audio may be emitted.
LOCK KEY
Push and hold to electronically lock all programmable keys
except the following:
[Moni], [Light], [Lock], [Emergency], [Surveillance] and [OPT 1/2/3].
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL DESCRIPTION
1
LIGHT KEY
OPT 1/2/3 KEYS
Push to control the output signal level from the optional unit
connector.
1
2
3
Push to turn the transceiver’s backlight ON for about 5 sec.
when the backlight function is turned OFF in user set mode.
(p. 12)
CLOCK KEY
4
5
6
7
8
9
10
11
12
13
14
15
16
HIGH/LOW KEY
➥ Push to indicate the current time on the LCD. (p. 9)
• While the current time is indicated, push and hold this key for
1 sec. to enter the time data edit mode. (p. 9)
➥ Push and hold for 1 sec. to enter the clock set mode.
(pp. 10, 11)
Push to select the transmit output power temporarily or per-
manently, depending on the pre-setting.
• Ask your dealer for the output power level for each selection.
• During in the clock set mode, push this key to select an item,
and change the value or condition by pushing [CH Up] or [CH
Down].
SURVEILLANCE KEY
Push to turn the surveillance function ON or OFF.
When this function is turned ON, the beep is not emitted and
the LCD backlight does not light when a signal is received or
a key is pushed, etc.
HOME KEY
Push to return to normal operation.
HOOK SCAN KEY
When the on hook scan function is activated, push this key
to stop scanning temporarily. Push this key again to re-start
scanning.
USER SET MODE KEY
➥ Push and hold to enter user set mode.
• During in the user set mode, push this key to select an item that
is enabled by your dealer, and change the value or condition by
pushing [CH Up] or [CH Down].
➥ Push and hold this key again to exit user set mode.
User set mode is also available via the ‘Power ON function.’
Refer to p. 12 also.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
2
n Turning power ON
n Channel selection
When you use the transceiver for the first time, or after the
transceiver has been left unused for a long time, make
sure to check the date and time indication after turning the
power ON. If the time and date are not correct, reset them.
(p. 9)
Several types of channel selections are available. Methods
may differ according to your system set up.
NON-ZONE TYPE:
To select the desired operating channel:
• Push [CH Up] or [CH Down].
• Push one of [MR-CH 1] to [MR-CH 4].
q Push [ ] to turn the power ON.
w If the transceiver is programmed for a start up password,
input the digit codes as directed by your dealer.
• 10-keypad can be used for password input.
ZONE TYPE:
To select the desired zone:
• The keys as below can be used for password input:
The transceiver detects numbers in the same block as identical.
Therefore “01234” and “56789” are the same.
• Push [Zone], then push [CH Up] or [CH Down].
AUTOMATIC SCAN TYPE:
Channel setting is not necessary for this type. When turn-
ing power ON, the transceiver automatically starts scanning.
Scanning stops when receiving a call.
P0
P1
P2
P3
P4
KEY
0
5
1
6
2
7
3
8
4
9
NUMBER
P0
P1
P2
P3
P4
*In this instruction manual, these keys are
from the left, called [P0]/[P1]/[P2]/[P3]/[P4].
e When the “PASSWORD” indication does not clear after in-
putting 6 digits, the input code number may be incorrect.
Turn the power OFF and start over in this case.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
2
1
2
3
4
n Receiving and transmitting
Receiving:
q Push [ ] to turn the power ON.
w Push [CH Up] or [CH Down] to select a channel in se-
quence.
D Transmitting notes
• Transmit inhibit function
The transceiver has several inhibit functions which restrict
transmission under the following conditions:
-The channel is in mute condition (‘Inaudible’ condition;
e While receiving a call, adjust the audio output level to a
comfortable listening level.
5
6
“
” does not appear.)
-The channel is busy.
-Un-matched (or matched) CTCSS is received.
(Depending on the pre-setting)
-Un-matched (or matched) NAC is received.*
(Depending on the pre-setting)
-The selected channel is a ‘receive only’ channel.
*Digital mode operation only.
Transmitting:
7
8
9
10
11
12
13
14
15
16
Wait for the channel to become clear to avoid interference.
q Take the microphone off hook.
• The ‘audible’ condition is selected and BUSY indicator lights
green.
• A priority channel may be selected automatically.
w Wait for the channel to become clear.
• The channel is busy when BUSY indicator lights green.
e While pushing and holding [PTT], speak into the micro-
phone at your normal voice level.
• Time-out timer
After continuous transmission for the pre-programmed time
period, the time-out timer is activated, causing the transceiver
to stop transmitting.
r Release [PTT] to receive.
IMPORTANT: To maximize the readability of your signal;
1. Pause briefly after pushing [PTT].
2. Hold the microphone 5 to 10 cm (2 to 4 inches) from
your mouth, then speak into the microphone at a normal
voice level.
• Penalty timer
Once the time-out timer is activated, transmission is further
inhibited for a period determined by the penalty timer.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
2
n Clock function
The transceiver indicates the current time and date when
[Clock] is pushed. And you can change the indication format
and time/date settings.
D Time and date settings
q Push [Clock] to indicate the current time and date on the
LCD.
When you use the transceiver for the first time, or after the
transceiver has been left unused for a long time, make
sure to check the date and time indication after turning the
power ON. If the time and date are not correct, reset
them.
12HR 12:00PM
YMD 08-04-01
w Push and hold [Clock] for 1 sec. to enter the time and date
setting mode.
• The time indication format, “24HR” or “12HR” blinks.
D Time and date indication
q Push [Clock] to indicate the current time and date on the
LCD.
12HR 12:00PM
YMD 08-04-01
• When the indication format is set to 12-hour, “AM” or “PM” is
indicated.
• The LCD indication returns to the stand-by mode after 30 sec.
has passed with no operation.
e Push [Clock] to select the desired item to be changed.
r Push [CH Up] or [CH Down] to set the selected item.
The time indication format (12-hour/24-hour)
Time
12HR 03:00PM
YMD 08-04-01
12HR 12:00PM
YMD 08-04-01
Date
Date indication format (Y: Year, M: Month, D: Day)
w Push [Clock] again to return to the stand-by mode.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
2
1
2
3
n Wake up function
The wake up function allows the transceiver to be automati-
cally turned ON according to the wake up time setting.
t Push [Clock] to set.
• The next item blinks.
4
q Push and hold [Clock] for 1 sec. to enter the clock set
mode.
• “WAKE UP” is indicated.
5
6
12HR 03:00PM
YMD 08-04-01
WAKE UP
OFF
7
8
y Repeat steps e to t to set items.
u After setting, push and hold [Clock] for 1 sec. to program.
• Return to the time and date setting mode.
9
i Push [Clock] to return to the stand-by mode.
w Push [CH Up] or [CH Down] to turn the wake up function
ON.
10
11
12
13
14
15
16
e Push [Clock] to set, and select “WAKE UP TIME.”
WAKE UP TIME
07:25AM
r Push [CH Up] or [CH Down] to enter the wake up time edit
mode.
• The ‘hour’ digit blinks.
WAKE UP TIME
07:25AM
☞ Continues to the next page
10
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
2
n Sleep function
The sleep function allows the transceiver to be automatically
turned OFF according to the sleep time setting.
t Push [CH Up] or [CH Down] to input the ‘hour’ data for
wake up time. After inputting, push [Clock] to set.
• The ‘minutes’ digit blinks.
q Push and hold [Clock] for 1 sec. to enter the clock set
mode.
• “WAKE UP” is indicated.
w Push [Clock] several times to select “SLEEP.”
WAKE UP TIME
09:25AM
y Push [CH Up] or [CH Down] to input the ‘minutes’ data for
SLEEP
ON
wake up time. After inputting, push [Clock] to set.
WAKE UP TIME
09:30AM
e Push [CH Up] or [CH Down] to select “ON” or “ON EXCPT
EMR” to turn the sleep function ON.
• When “ON EXCPT EMER” is selected, the transceiver will be
automatically turned OFF at the sleep time. However, during the
emergency mode, the sleep function will not function, even if the
sleep time period starts.
u Push and hold [Clock] for 1 sec. to exit the clock set
mode.
• Return to the stand-by mode.
r Push [Clock] to set, and select “SLEEP TIME.”
SLEEP TIME
05:35PM
11
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
2
1
2
3
4
n User set mode
The user set mode is accessed at power ON and allows you
to set seldom-changed settings. You can “customize” the
transceiver operation to suit your preferences and operating
style.
t Push [CH Up] or [CH Down] to enter the sleep time edit
mode.
• The ‘hour’ digit blinks.
5
6
7
8
SLEEP TIME
05:35PM
Entering the user set mode:
q While pushing and holding [P1] and [P2], push [ ] to turn
the power ON.
• Turn power OFF in advance.
• You should hold [P1] and [P2] until “SET MODE” appears on the
display.
y Push [CH Up] or [CH Down] to input the ‘hour’ data for
sleep time. After inputting, push [Clock] to set.
• The ‘minutes’ digit blinks.
9
10
11
12
13
14
15
16
SLEEP TIME
08:35PM
[P1][P2]
[
]
u Push [CH Up] or [CH Down] to input the ‘minutes’ data for
w Push and hold [P0] to enter user set mode.
sleep time. After inputting, push [Clock] to set.
SLEEP TIME
08:00PM
[P0]
i Push and hold [Clock] for 1 sec. to exit the clock set
mode.
☞ Continues to the next page
• Return to the stand-by mode.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
2
e Push [P0] several times to select the appropriate item.
Then, push [Up] or [Down] to set the desired level/condi-
tion.
• Available set mode functions are Backlight, LCD Contrast,
Beep, Beep Level, Ringer Level, SQL Level, AF Min. Level,
Mic Gain, Horn, Battery Voltage, Signal Moni, Lone Worker
and System Information.
[P0]
[Up]/[Down]
r Push [ ] again to exit set mode.
[
]
User set mode is also available using a programmable key.
Refer to p. 6 [User Set Mode] section.
[User Set Mode] allows for quick item selection. Set “Enable”
for the often used items with the CS-F9010/F9510 cloning
software. Ask your dealer for details.
NOTE: While in the user set mode, [P0], [Up] and [Down]
activate regardless of the assigned functions.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION AND MAINTENANCE
3
1
2
3
4
n Separation cable connection
w Connect the separation cable to the controller as shown
CAUTION: To avoid damage to the transceiver, disconnect
the DC power cable from the transceiver before connecting
the separation cable.
below.
• The cable can be inserted into either the left or right grooves as
desired.
Rear plate
5
NOTE: The following connections should be performed by
your Icom dealer or distributor.
6
Screw the removed
circuit board screw
in step q to connect
the cable terminal.
The supplied or optional separation cable is required for the
controller and the main unit connection.
See “OPTIONS” on page 22 for the separation cable details.
7
8
9
10
11
12
13
14
15
16
Separation
cable
D Controller
q Unscrew the 4 screws, then remove the rear plate from the
controller.
Cable
groove
Rear plate
Controller
e After the cable connection, replace the removed rear plate
and the 4 screws, then connect the opposite side of the
separation cable to the main unit. (See the next page)
Unscrew the cir-
cuit board screw.
Controller
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION AND MAINTENANCE
3
D Main unit
q Unscrew the 4 screws of the front plate (either the left or
right), then remove the front plate from the main unit.
w Connect the opposite side of the separation cable that is
connected to the controller described on the previous page
as shown below.
• The cable can be inserted into either the left or right grooves as
desired.
Unscrew the cir-
cuit board screw.
Front plate
Screw the removed
Front plate
circuit board screw
in step q to connect
the cable terminal.
Main unit
Separation
cable
Cable grooves
Main unit
e After the cable connection, replace the removed front plate
and the 4 screws, then connect the DC power cable.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION AND MAINTENANCE
3
1
2
3
4
Antenna
n Rear panel connection
NOTE: The following
connections should be
performed by your Icom
dealer or distributor.
q D-SUB 25-PIN w ANTENNA CONNECTOR
Connects to an antenna.
Contact your dealer about an-
tenna selection and placement.
Connect an
external unit.
5
e
RWARNING! NEVER re-
move the fuse-holders from
the black and red cables.
6
7
w
q
8
9
+ red
t
_ black
10
11
12
13
14
15
16
r
When the optional micro-
phone (HM-152/T) is used:
Crimp
12V
Battery
Crimp terminal
e MICROPHONE HANGER
t DC POWER RECEPTACLE
Connects to a 12 V DC battery.
Pay attention to polarities.
NOTE: Use the terminals
as shown below for the
cable connections.
The supplied self ground microphone
can be used for microphone on/off
hook functions. (See p. 2)
Purchase separately
Connect the supplied micro-
phone hanger to the vehicle’s
ground for microphone on/off
hook functions when the op-
tional microphone (HM-152/T)
is used.
Crimp
Solder
RWARNING! NEVER connect
to a 24 V battery. This could
damage the transceiver.
r EXTERNAL SPEAKER
CONNECTOR
Connect a 4–8 ø external speaker.
(See p. 21 for connector information.)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION AND MAINTENANCE
3
n Supplied Accessories
Microphone
Microphone hanger
and screw set
Mounting bracket
for main unit
Flat washers
(M5)
Mounting screws
(M5×12)
Spring washers
(M5)
Self-tapping screws
(M5×16)
Black and red cables
with fuse holders
DC power cable
Nuts (M5)
Bracket bolts
Socket terminals
Fuses*1
Crimp terminals
Binding bands
Mounting bracket
for controller
Flat washers
(M5)
Mounting screws
(M5×12)
Spring washers
(M5)
Self-tapping screws
(M5×16)
Separation
cable
Function name
stickers*2
KEY-STICKER
Nuts (M5)
Bracket screws
Key caps
Housing
*1 Fuses should be installed in the fuse holder of the black and red cables, respectively.
See p. 20 for details.
*2 Used for labelling the programmable function keys according to their assinged functions.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION AND MAINTENANCE
3
1
2
3
4
n Mounting the transceiver
• Function name stickers
D Main unit
There are no names on the programmable function keys
since the functions can be freely assigned to these keys.
Attach the supplied function name stickers as below to the
appropriate keys for easy recognition of the key’s assigned
function.
The universal mounting bracket supplied with your transceiver
allows overhead mounting.
• Mount the main unit securely with the 4 supplied screws to a
thick surface which can support more than 8 kg (17.63 lb).
5
Nut
6
7
Then, protect the attached stickers from unsticking with the
supplied key cap as below.
Flat
washer
8
9
10
11
12
13
14
15
16
Function name sticker
Key cap
Felt*
Bracket
bolt
• Housing
Insert the speaker cable terminals to the appropriate slots
of the supplied housing. See p. 21 for the speaker connector
information.
Spring washer
When using
self-tapping screws
*Felts reduce the vibration effects.
Speaker cable terminals
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION AND MAINTENANCE
3
D Controller
2 types of mounting styles are available— one is overhead
mounting, and other one is on-board mounting.
Overhead mounting
• Mount the controller securely with the 4 supplied screws to
a thick surface which can support more than 2 kg (4.40 lb).
(Overhead mounting)
On-board mounting
Flat washer
Spring washer
Bracket screw
Bracket
screw
When using
self-tapping screws
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION AND MAINTENANCE
3
1
2
3
4
5
6
7
n Antenna
A key element in the performance of any communication sys-
tem is an antenna. Contact your dealer about antennas and
the best places to mount them.
n Cleaning
If the transceiver becomes dusty or dirty, wipe it clean with a
soft, dry cloth.
DO NOT use harsh solvents such as benzine or
alcohol, as they may damage the transceiver sur-
faces.
n Fuse installation
Fuses should be installed in the fuse holder of the black and
red cables, respectively.
If a fuse blows or the transceiver stops functioning, track
down the source of the problem, have it repaired, and replace
the damaged fuse with a new rated one.
❑ Fuse rating: 30 A
8
9
10
11
12
13
14
15
16
USE a 30 A fuse of the same type only.
30 A fuse
20
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION AND MAINTENANCE
3
n
Speaker connector information
q w e
r t y
u i o
Connector’s front view
Pin No. Name
Description
Specifications
0 − Vcc
q
w
e
r
t
y
IGN
IGSW cont. In
Output power : Max. 20 W
Impedance : 4 ø
RXSP1 RX AF Out (BTL)
NC
HORN1* Horn drive cont. Out
—
—
0 − Vcc
Output current: Max. 1 A
HORN2* Horn drive cont. Out 0 − Vcc
Output power : Max. 20 W
RXSP2 RX AF Out (BTL)
Impedance : 4 ø
Output power : Max. 20 W
Impedance : 4 ø
u
PS1
AF Out to PA (BTL)
Output power : Max. 20 W
Impedance : 4 ø
i
o
PS2
AF Out to PA (BTL)
Connects to ground.
GND
—
* When the horn function is activated, HORN1 and HORN2
are shorted.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONS
4
• OPC-607/OPC-608/OPC-609/OPC-726
s e pa r at i o n c a b l e s
Approved Icom optional equipment is designed for optimal
performance when used with an Icom transceiver.
Icom is not responsible for the destruction or damage to an
Icom transceiver in the event it is used with equipment that
is not manufactured or approved by Icom.
1
2
3
Used for a controller and a main unit connection.
OPC-607 : 3 m; 9.84 ft
OPC-608 : 8 m; 26.3 ft
OPC-609 : 1.9 m; 6.3 ft
OPC-726 : 5 m; 16.4 ft
4
5
6
7
Some options may not be available in some countries. Please
ask your dealer for details.
• SP-30 e x t e r n a l s p e a k e r
Input impedance : 4 ø
Max. input power : 40 W
• HM-152/HM-152T/HM-148G h a n d m i c ro p h o n e s
HM-152 : Hand microphone
HM-152T : DTMF microphone
8
9
HM-148G: Self ground heavy duty microphone
10
11
12
13
14
15
16
• SM-25 d e s k to p m i c ro p h o n e
• OPC-1532/OPC-1871 z o n e c o p y c a b l e s
OPC-1532 : Mobile to mobile zone copy cable.
OPC-1871 : Mobile to handy zone copy cable.
• UT-125 a e s /d e s e n c ry p t i o n u n i t
• UT-128 d e s e n c ry p t i o n u n i t
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY TRAINING INFORMATION
5
Your Icom radio generates RF electromagnetic en-
To ensure that your exposure to RF electromag-
ergy during transmit mode.This radio is designed
for and classified as “Occupational Use Only”,
meaning it must be used only during the course of
employment by individuals aware of the hazards,
and the ways to minimize such hazards.This radio
is NOT intended for use by the “General Popula-
tion” in an uncontrolled environment.
netic energy is within the FCC allowable limits
for occupational use, always adhere to the fol-
lowing guidelines:
CAUTION
WARNING
• DO NOT operate the radio without a proper antenna attached, as
this may damage the radio and may also cause you to exceed FCC
RF exposure limits. A proper antenna is the antenna supplied with
this radio by the manufacturer or an antenna specifically authorized
by the manufacturer for use with this radio.
• DO NOT transmit for more than 50% of total radio use time (“50%
duty cycle”).Transmitting more than 50% of the time can cause FCC
RF exposure compliance requirements to be exceeded. The radio
is transmitting when the “TX indicator” lights red.You can cause the
radio to transmit by pressing the “PTT” switch.
• For compliance with FCC and Industry Canada RF Exposure Re-
quirements, the transmitter antenna installation shall comply with
the following two conditions:
1. The transmitter antenna gain shall not exceed 0 dBi.
2. IC-F9511HT:
The antenna is required to be located outside of a vehicle and kept
at a distance of 66.2 centimeters or more between the transmitting
antenna of this device and any persons during operation. For small
vehicle as worst case, the antenna shall be located on the roof top
at any place on the centre line along the vehicle in order to achieve
66.2 centimeters separation distance. In order to ensure this dis-
tance is met, the installation of the antenna must be mounted at
least 66.2 centimeters away from the nearest edge of the vehicle in
order to protect against exposure to bystanders.
3. Transmit only when people outside the vehicle are at least the
recommended minimum distance of 148 centimeters away from
the properly installed antenna. This separation distance will en-
sure that there is sufficient distance from a properly installed
externally-mounted antenna to satisfy the RF exposure require-
ments in the applicable RF exposure compliance standards.
Electromagnetic Interference/Compatibility
During transmissions, your Icom radio generates RF energy that can
possibly cause interference with other devices or systems. To avoid
such interference, turn off the radio in areas where signs are posted
to do so. DO NOT operate the transmitter in areas that are sensitive
to electromagnetic radiation such as hospitals, aircraft, and blasting
sites.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
A-6718D-1US-w
Printed in Japan
© 2008−2010 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Printed on recycled paper with soy ink.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
