Operator′s manual
K760
K760 Rescue
Please read the operator’s manual carefully and make sure you understand the instructions
before using the machine.
GB English
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Cleaning ................................................................ 25
Contents
Functional inspection ............................................ 25
TECHNICAL DATA
KEY TO SYMBOLS
Manual version .....................................................
Symbols on the machine ......................................
Explanation of warning levels ...............................
CONTENTS
2
2
2
Technical data ....................................................... 29
Cutting equipment ................................................. 29
EC-declaration of conformity ................................ 30
Contents ...............................................................
PRESENTATION
3
Dear Customer, ....................................................
Design and features .............................................
PRESENTATION
4
4
What is what on the power cutter - K760? ...........
PRESENTATION
5
6
7
9
What is what on the power cutter - K760 Rescue?
MACHINE´S SAFETY EQUIPMENT
General .................................................................
CUTTING BLADES
General .................................................................
Abrasive blades .................................................... 10
Diamond blades ................................................... 10
Toothed blades, carbide tipped blades and
emergency situations ........................................... 11
Transport and storage .......................................... 11
ASSEMBLING AND ADJUSTMENTS
General ................................................................. 12
Checking the drive shaft and flange washers ....... 12
Checking the bushing ........................................... 12
Checking the direction of the blade rotation ......... 12
Fitting the cutting blade ........................................ 12
Blade guard .......................................................... 12
Disengaging OilGuard .......................................... 13
Reversible cutting head ........................................ 13
FUEL HANDLING
General ................................................................. 14
Fuel ...................................................................... 14
Fueling .................................................................. 15
Transport and storage .......................................... 15
OilGuard ............................................................... 15
OPERATING
Protective equipment ............................................ 16
General safety precautions ................................... 16
Transport and storage .......................................... 21
STARTING AND STOPPING
Before starting ...................................................... 22
Starting ................................................................. 22
Stopping ............................................................... 23
MAINTENANCE
General ................................................................. 24
Maintenance schedule ......................................... 24
English – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRESENTATION
Dear Customer,
Thank you for choosing a Husqvarna product!
Design and features
This is a high speed, hand held, power cutter designed to
cut hard materials like masonry or steel and should not be
used for any purpose not described in this manual. Safe
operation of this product requires the operator to read this
manual carefully. Ask your dealer or Husqvarna should
you need more information.
It is our wish that you will be satisfied with your product
and that it will be your companion for a long time. A
purchase of one of our products gives you access to
professional help with repairs and services. If the retailer
who sells your machine is not one of our authorised
dealers, ask him for the address of your nearest service
workshop.
Some of the unique features of your product are
described below.
Active Air Filtration™
Centrifugal air cleaning for longer service life and longer
service intervals.
This operator’s manual is a valuable document. Make
sure it is always at hand at the work place. By following its
content (using, service, maintenance etc) the life span
and the second-hand value of the machine can be
extended. If you will sell this machine, make sure that the
buyer will get the operator´s manual.
OilGuard (K760 OilGuard)
An optical detection system to detect if there is oil in the
fuel or if the oil type is wrong.
SmartCarb™
More than 300 years of innovation
Built-in automatic filter compensation maintains high
power and reduces fuel consumption.
Husqvarna AB is a Swedish company based on a tradition
that dates back to 1689, when the Swedish King Charles
XI ordered the construction of a factory for production of
muskets. At that time, the foundation was already laid for
the engineering skills behind the development of some of
the world's leading products in areas such as hunting
weapons, bicycles, motorcycles, domestic appliances,
sewing machines and outdoor products.
Dura Starter™
Dust sealed starter unit, where the return spring and the
pulley bearing are sealed which makes the starter
virtually maintenance free and even more reliable.
X-Torq®
The X-Torq® engine provides a more accessible torque
for a wider range of speeds which results in maximum
cutting capacity. X-Torq® reduces the fuel consumption
by up to 20% and the emissions by up to 60%.
Husqvarna is the global leader in outdoor power products
for forestry, park maintenance and lawn and garden care,
as well as cutting equipment and diamond tools for the
construction and stone industries.
EasyStart
Owner responsibility
The engine and starter are designed to ensure quick and
easy starting of the machine. Reduces the pull resistance
in the starter cord by up to 40%. (Reduces the
compression during starting.)
It is the owner’s/employer’s responsibility that the operator
has sufficient knowledge about how to use the machine
safely. Supervisors and operators must have read and
understood the Operator’s Manual. They must be aware
of:
Air purge
When you push the air purge diaphragm, fuel is pumped
through to the carburettor. Fewer pulls are required for
starting, meaning the machine becomes easier to start.
•
•
•
The machine’s safety instructions.
The machine’s range of applications and limitations.
How the machine is to be used and maintained.
DEX
Low flushing wet cutting kit for effective dust handling.
National legislation could regulate the use of this
machine. Find out what legislation is applicable in the
place where you work before you start using the machine.
Efficient vibration damping system
Efficient vibration dampers spare arms and hands.
Reversible cutting head
The machine is fitted with a reversible cutting head
allowing cutting close to a wall or at ground level,
restricted only by the thickness of the blade guard.
The manufacturer’s reservation
Subsequent to publishing this manual Husqvarna may
issue additional information for safe operation of this
product. It is the owner’s duty to keep up with the safest
methods of operation.
Specially designed starter handle
(K760 Rescue)
Specially designed starter handle, with room for heavy
gloves.
Husqvarna AB has a policy of continuous product
development and therefore reserves the right to modify
the design and appearance of products without prior
notice.
Adjustable carry strap (K760 Rescue)
Adjustable carry strap for full freedom of movement.
For customer information and assistance, contact us at
Chromium-plated blade guard
(K760 Rescue)
Chromium-plated blade guard, visible in smoke and water
spray, enhances control of the cutter.
4 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
PRESENTATION
What is what on the power cutter - K760?
1
2
3
4
5
6
7
8
9
Front handle
15 Blade guard
Water tap
16 Decompression valve
Warning decal
Air filter cover
17 Air purge
18 Fuel cap
Cylinder cover
19 Water connection with filter
20 Belt guard
Choke control with start throttle lock
Throttle lockout
Throttle trigger
Stop switch
21 Cutting arm
22 Rating plate
23 Belt tensioner
10 Disconnection function for OilGuard (K760 OilGuard)
24 Cutting head
11 Starter handle
12 Starter
25 Cutting blade (not supplied)
26 Combination spanner
27 Water connector, GARDENA®
28 Operator′s manual
13 Muffler
14 Adjustment handle for guard
English – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
PRESENTATION
What is what on the power cutter - K760 Rescue?
1
2
3
4
5
6
7
8
9
Front handle
14 Decompression valve
Warning decal
15 Air purge
Air filter cover
16 Fuel cap
Cylinder cover
17 Harness
Choke control with start throttle lock
Throttle lockout
Throttle trigger
18 Belt guard
19 Cutting arm
20 Rating plate
Stop switch
21 Belt tensioner
22 Cutting head
23 Cutting blade (not supplied)
24 Combination spanner
25 Operator′s manual
Starter handle
10 Starter
11 Muffler
12 Adjustment handle for guard
13 Blade guard
6 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE´S SAFETY EQUIPMENT
•
Check that the throttle trigger and throttle lockout
move freely and that the return springs work properly.
General
WARNING! Never use a machine that has
faulty safety equipment! If your machine
fails any checks contact your service
agent to get it repaired.
!
The engine should be switched off, and
the stop switch in STOP position.
•
Start the power cutter and apply full throttle. Release
the throttle control and check that the cutting blade
stops and remains stationary. If the cutting blade
rotates when the throttle is in the idle position you
should check the carburettor’s idle adjustment. See
instructions in the section "Maintenance".
This section describes the machine´s safety equipment,
its purpose, and how checks and maintenance should be
carried out to ensure that it operates correctly.
Throttle lockout
The throttle trigger lock is designed to prevent accidental
operation of the throttle. When the lock (A) is pressed in
this releases the throttle (B).
Stop switch
Use the stop switch to switch off the engine.
The trigger lock remains pressed in as long as the throttle
is pressed. When the grip on the handle is released the
throttle trigger and the throttle trigger lock both return to
their original positions. This is controlled by two
independent return spring systems. This means that the
throttle trigger is automatically locked in the idle position.
Checking the throttle lockout
•
Make sure the throttle control is locked at the idle
setting when the throttle lockout is released.
Checking the stop switch
•
Start the engine and make sure the engine stops
when you move the stop switch to the stop setting.
•
Press the throttle lockout and make sure it returns to
its original position when you release it.
English – 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE´S SAFETY EQUIPMENT
Checking the vibration damping system
Blade guard
WARNING! The engine should be
switched off, and the stop switch in
STOP position.
WARNING! Always check that the guard
is correctly fitted before starting the
machine.
!
!
•
•
Check the vibration damping units regularly for cracks
or deformation. Replace them if damaged.
This guard is fitted above the cutting blade and is
designed to prevent parts of the blade or cutting
fragments from being thrown towards the user.
Check that the vibration damping element is securely
attached between the engine unit and handle unit.
Muffler
WARNING! Never use a machine without
a muffler, or with a faulty muffler. A
damaged muffler may substantially
increase the noise level and the fire
hazard. Keep fire fighting equipment
handy.
!
Checking the blade and the blade guard
The muffler gets very hot during and
after use as well as when idling. Be
aware of the fire hazard, especially when
working near flammable substances and/
or vapours.
•
Check that the guard over the cutting blade is not
cracked or damaged in any other way. Replace when
damaged.
•
Check that the cutting blade is fitted correctly and
does not show signs of damage. A damaged cutting
blade can cause personal injury.
Keep fire fighting equipment handy.
Vibration damping system
The muffler is designed to keep noise levels to a minimum
and to direct exhaust fumes away from the user.
WARNING! Overexposure to vibration
can lead to circulatory damage or nerve
damage in people who have impaired
circulation. Contact your doctor if you
experience symptoms of overexposure
to vibration. Such symptoms include
numbness, loss of feeling, tingling,
pricking, pain, loss of strength, changes
in skin colour or condition.These
symptoms normally appear in the
fingers, hands or wrists.These
!
symptoms may be increased in cold
temperatures.
Inspecting the muffler
Check regularly that the muffler is complete and secured
correctly.
•
•
Your machine is equipped with a vibration damping
system that is designed to minimize vibration and
make operation easier.
The machine′s vibration damping system reduces the
transfer of vibration between the engine unit/cutting
equipment and the machine′s handle unit.The engine
body, including the cutting equipment, is insulated
from the handles by vibration damping units.
8 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTING BLADES
Cutting blades for different materials
General
WARNING! Never use a cutting blade for
any other materials than what it was
intended to cut.
WARNING! A cutting blade may burst
and cause injury to the operator.
!
!
Never use a diamond blade to cut plastic
material.The heat produced during cutting
may melt the plastic and it can stick to the
cutting blade and cause a kickback.
The cutting blade manufacturer issues
warnings and recommendations for the
use and proper care of the cutting blade.
Those warnings come with the cutting
blade. Read and follow all instructions
from the cutting blade manufacturer.
Cutting metal generates sparks that may
cause fire. Do not use the machine near
ignitable substances or gases.
A cutting blade should be checked
before it is assembled on the saw and
frequently during use. Look for cracks,
lost segments (diamond blades) or
pieces broken off. Do not use a damaged
cutting blade.
Follow the instructions supplied with the cutting blade
concerning the suitability of the blade for various
applications, or consult your dealer in case of doubts.
Concrete Metal Plastic
Cast iron
Test the integrity of each new cutting
blade by running it at full throttle for
about 1 minute.
Abrasive
blades
X
X
X
X
X
Diamon
d blades
X*
X*
•
Cutting blades are available in two basic designs;
abrasive blades and diamond blades.
* Only specialty blades.
Hand held, high speed machines
WARNING! Never use a cutting blade with a
lower speed rating than that of the power
cutter. Only use cutting blades intended for
high speed handheld power cutters.
!
•
•
High-quality blades are often most economical.Lower
quality blades often have inferior cutting capacity and
a shorter service life, which results in a higher cost in
relation to the quantity of material that is cut.
•
Many cutting blades that might fit this power cutter are
intended for stationary saws and have a lower speed
rating than is needed for this hand-held saw. Cutting
blades with a lower speed rating shall never be used
on this saw.
Make sure that the right bushing is used for the cutting
blade to be fitted on the machine. See the instructions
under the heading Fitting the cutting blade.
•
•
Husqvarna cutting blades are manufactured for high-
speed, portable power cutters.
Check that the blade is approved for the same or
higher speed according to the aproval plate of the
engine. Never use a cutting blade with a lower speed
rating than that of the power cutter.
Suitable cutting blades
Cutting blades K760
Abrasive blades Yes*
Diamond blades Yes
K760 Rescue
Yes*
Yes
Toothed blads
Do not use Yes**
For more information, see the ”Technical data” section.
*Without water
**See instructions under the heading "Toothed blades,
carbide tipped blades and emergency situations".
Blade vibration
•
The blade can become out-of-round and vibrate if an
excessive feed pressure is used.
•
A lower feed pressure can stop the vibration.
Otherwise replace the blade.
English – 9
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTING BLADES
Abrasive blades
Diamond blades
General
WARNING! Do not use abrasive blades
with water.The strength is impaired
when abrasive blades are exposed to
water or moisture, which results in an
increased risk of the blade breaking.
!
WARNING! Never use a diamond blade to
cut plastic material.The heat produced
during cutting may melt the plastic and it
can stick to the cutting blade and cause a
kickback.
!
•
The cutting material on abrasive blades consists of
grit bonded using an organic binder. ”Reinforced
blades” are made up of a fabric or fibre base that
prevents total breakage at maximum working speed if
the blade should be cracked or damaged.
Diamond blades become very hot when
used. An overheated blade is a result of
improper use, and may cause
deformation of the blade, resulting in
damage and injuries.
•
•
A cutting blade’s performance is determined by the
type and size of abrasive corn, and the type and
hardness of the bonding agent.
Cutting metal generates sparks that may
cause fire. Do not use the machine near
ignitable substances or gases.
Ensure the cutting blade is not cracked or damaged.
•
•
Diamond blades consist of a steel core provided with
segments that contain industrial diamonds.
Diamond blades ensure lower costs per cutting
operation, fewer blade changes and a constant cutting
depth.
•
Test the abrasive blade by hanging it on your finger
and tapping it lightly with a screwdriver or the like. If
the blade does not produce a resonant, ringing sound
it is damaged.
•
When using diamond blades make sure that it rotates
in the direction indicated by the arrow on the blade.
Abrasive blades for different materials
Blade type
Material
Diamond blades for different materials
Concrete, asphalt, stone masonry,
•
•
•
Diamond blades are ideal for masonry, reinforced
concrete and other composite materials.
Concrete blade cast iron, aluminium, copper, brass,
cables, rubber, plastic, etc.
Diamond blades are available in several hardness
classes.
Steel, steel alloys and other hard
Metal blade
metals.
Special blades should be used when cutting metal.
Ask your dealer for help in choosing the right product.
Sharpening diamond blades
•
•
Always use a sharp diamond blade.
Diamond blades can become dull when the wrong
feeding pressure is used or when cutting certain
materials such as heavily reinforced concrete.
Working with a blunt diamond blade causes
overheating, which can result in the diamond
segments coming loose.
•
Sharpen the blade by cutting in a soft material such as
sandstone or brick.
10 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTING BLADES
Diamond blades and cooling
•
During cutting the friction in the cut causes the
diamond blade to be heated up. If the blade is allowed
to get too hot this can result in loss of blade tensioning
or core cracking.
Diamond blades for dry cutting
•
Although no water is required for cooling, dry cutting
blades must be cooled with air flow around the blades.
For this reason dry cutting blades are recommended
only for intermittent cutting. Every few seconds of
cutting the blade should be allowed to run 'free” with
no load to allow the air flow around the blade to
dissipate the heat.
Diamond blades for wet cutting
•
Wet cutting diamond blades must be used with water
to keep the blade core and segments cool during
sawing.
•
•
Wet cutting blades should NOT be used dry.
Using wet cutting blades without water can cause
excessive heat build-up, resulting in poor
performance, severe blade damage and is a safety
hazard.
•
Water cooling cools the blade and increases its
service life while also reducing the formation of dust.
Toothed blades, carbide tipped
blades and emergency situations
Carbide tipped specialty blades are intended only for use
in rescue missions and only by trained staff.
Transport and storage
•
Do not store or transport the power cutter with the
cutting blade fitted.All blades should be removed from
the cutter after use and stored carefully.
•
Store cutting blades in dry, frost free conditions.
Special care should be taken with abrasive blades.
Abrasive blades must be stored on a flat, level
surface. If an abrasive blades is stored in humid
conditions, this can cause imbalance and result in
injury.
•
Inspect new blades for transport or storage damage.
English – 11
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLING AND ADJUSTMENTS
General
Checking the direction of the
blade rotation
WARNING! The engine should be
•
When using diamond blades make sure that it rotates
in the direction indicated by the arrow on the blade.
The direction of rotation for the machine is shown by
arrows on the cutting arm.
switched off, and the stop switch in
STOP position.
!
Husqvarna’s blades are high speed blades approved for
hand held power cutters.
Checking the drive shaft and
flange washers
When the blade is replaced with a new one, check the
flange washers and the drive shaft.
•
Check that the threads on the drive shaft are
undamaged.
Fitting the cutting blade
•
Check that the contact surfaces on the blade and the
flange washers are undamaged, of the correct
dimension, clean, and that they run properly on the
drive axle.
•
The blade is placed on the bushing (A) between the
inner flange washer (B) and the flange washer (C).
The flange washer is turned so that it fits on the axle.
•
•
Lock the shaft. Insert a tool in the hole in the cutting
head and rotate the blade until it is locked.
Do not use warped, notched, indented or dirty flange
washers. Do not use different dimensions of flange
washers.
Checking the bushing
Bushings are used to fit the machine to the centre hole in
the cutting blade.The machine is supplied with a bushing
that can be flipped over to fit either 20 mm or 1” (25.4
mm). A decal on the blade guard indicates appropriate
blade specification.
Tightening torque for the bolt holding the blade is: 25
Nm (215 in.lb).
Blade guard
The guard for the cutting equipment should be adjusted
so that the rear section is flush with the work piece.
Spatter and sparks from the material being cut are then
collected up by the guard and led away from the user.
The blade guard is friction locked.
•
Check that the bushing on the machine's spindle shaft
corresponds with the centre hole of the cutting blade.
The blades are marked with the diameter of the centre
hole.
•
Press the ends of the guard against the work piece or
adjust the guard with the adjustment handle. The
guard must always be fitted on the machine.
Use only bushings supplied by Husqvarna. Those
bushings have been designed for your power cutter.
12 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLING AND ADJUSTMENTS
Disengaging OilGuard
(K760 OilGuard)
Reversible cutting head
The machine is fitted with a reversible cutting head
allowing cutting close to a wall or at ground level,
restricted only by the thickness of the blade guard.
•
When the machine is delivered, the OilGuard plug (A)
and the blue indicator pin (B) are fitted in the tank.
In the event of a kickback it is harder to control the
machine when cutting with the cutting head reversed.The
cutting blade is further away for the centre of the machine
which means the handle and the cutting blade are no
longer in alignment. It is more difficult to restrain the
machine if the blade gets jammed or stuck in its kickback
danger zone. See under the "Kickback" heading in the
"Operating" section for additional information.
Some of the machine’s good ergonomic features are
jeopardised such as balance. Cutting with the cutting
head reversed should only occur with cuts that are not
possible in a standard manner.
•
•
•
If you are in a situation where you do not have access
to Husqvarna OilGuard oil, but you have oil of a similar
quality, you can deactivate the OilGuard system using
the disconnection function.
•
First release the two bolts and then the adjuster screw
to release the belt tension.
To deactivate the function, pry off the OilGuard plug
using a screwdriver and then break off the indicator
pin. Now fit the disconnector plug (C) in the tank to
complete deactivation and to cover the hole.
If you want to reactivate the OilGuard system, press
the OilGuard plug again. The system is then
reactivated, but note that the broken indicator pin
cannot be refitted.
•
•
A broken indicator pin indicates that the OilGuard
system has been disconnected.
•
Now unscrew the bolts and dismantle the belt guard.
You can purchase a new indicator pin as a spare, but
this is only sold in grey which indicates that the
OilGuard system has been deactivated since the
machine left the factory.
•
•
Disconnect the water hose from the blade guard.
Remove the belt from the belt pulley.
•
•
The cutting head is now loose and can be removed
from the machine.
Remove the cutting head and attach it to the other
side of the cutting arm.
•
•
Fit the belt guard to the reversed cutting head.
Tighten the drive belt. See instructions in the section
"Maintenance".
•
Assemble the water hose nipple and the hose on the
opposite upper side of the blade guard.
English – 13
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Two-stroke oil
General
K760
WARNING! Running an engine in a
•
•
•
For best results and performance use HUSQVARNA
two-stroke engine oil, which is specially formulated for
our air-cooled two-stroke engines.
confined or badly ventilated area can
result in death due to asphyxiation or
carbon monoxide poisoning. Use fans to
ensure proper air circulation when
working in trenches or ditches deeper
than one meter.
!
Never use two-stroke oil intended for water-cooled
engines, sometimes referred to as outboard oil (rated
TCW).
Never use oil intended for four-stroke engines.
Fuel and fuel fumes are flammable and
can cause serious injury when inhaled or
allowed to come in contact with the skin.
For this reason observe caution when
handling fuel and make sure there is
adequate ventilation.
K760 OilGuard
Use HUSQVARNA OilGuard two stroke oil.
•
Mixing
•
Always mix the petrol and oil in a clean container
intended for fuel.
The exhaust fumes from the engine are
hot and may contain sparks which can
start a fire. Never start the machine
indoors or near combustible material!
•
Always start by filling half the amount of the petrol to
be used. Then add the entire amount of oil. Mix
(shake) the fuel mixture. Add the remaining amount of
petrol.
Do not smoke and do not place any hot
objects in the vicinity of fuel.
•
•
Mix (shake) the fuel mixture thoroughly before filling
the machine’s fuel tank.
Fuel
Do not mix more than one month’s supply of fuel at a
time.
NOTICE! The machine is equipped with a two-stroke
engine and must always been run using a mixture of
petrol and two-stroke oil. It is important to accurately
measure the amount of oil to be mixed to ensure that the
correct mixture is obtained.When mixing small amounts
of fuel, even small inaccuracies can drastically affect the
ratio of the mixture.
Mixing ratio
• 1:50 (2%) with HUSQVARNA two-stroke oil or
equivalent.
Two-stroke oil, litre
Petrol, litre
2% (1:50)
0,10
5
Petrol
10
15
20
0,20
•
•
Use good quality unleaded or leaded petrol.
0,30
The lowest octane recommended is 90 (RON). If you
run the engine on a lower octane grade than 90 so-
called knocking can occur. This gives rise to a high
engine temperature, which can result in serious
engine damage.
0,40
•
1:33 (3%) with oils class JASO FB or ISO EGB
formulated for air-cooled, two-stroke engines or mix
as per recommendation from the oil manufacturer.
•
When working at continuous high revs a higher octane
rating is recommended.
Environment fuel
HUSQVARNA recommends the use of alkylate fuel,
either Aspen two-stroke fuel or environmental fuel for
four-stroke engines blended with two-stroke oil as set out
below. Note that carburettor adjustment may be
necessary when changing the type of fuel (see the
instructions under the heading Carburettor).
Ethanol blended fuel, E10 may be used (max 10%
ethanol blend). Using ethanol blends higher than E10 will
create lean running condition which can cause engine
damage.
14 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Fueling
OilGuard (K760 OilGuard)
•
Machines fitted with OilGuard have a built-in system
for identifying incorrect fuel mixtures.
WARNING! Always stop the engine and
let it cool for a few minutes before
refuelling.The engine should be
switched off, and the stop switch in
STOP position.
!
•
Once the machine is running, a detector reads the fuel
quality which takes about ten seconds. If the correct
amount of Husqvarna OilGuard oil has been used, the
machine will run at a normal speed. If the wrong type
of oil has been used, the machine senses this and
restricts the speed of the engine to 3,800 rpm to avoid
damaging the engine.
When refuelling, open the fuel cap slowly
so that any excess pressure is released
gently.
•
In order for the machine to run at normal speed again,
you must drain the incorrect fuel mixture and then fill
the machine with a fuel mixture containing the correct
ratio (2 %) of Husqvarna OilGuard oil.
Clean the area around the fuel cap.
Tighten the fuel cap carefully after
refuelling.
If the cap is not properly tightened the
cap might vibrate lose and fuel may
escape from the fuel tank creating a fire
hazard.
Move the machine at least 3 m from the
refuelling point before starting it.
Never start the machine:
•
If you have spilt fuel or engine oil on the machine.
Wipe off the spill and allow the remaining fuel to
evaporate.
•
If you have spilt fuel on yourself or your clothes,
change your clothes.Wash any part of your body that
has come in contact with fuel. Use soap and water.
•
•
If the machine is leaking fuel. Check regularly for
leaks from the fuel cap and fuel lines.
Unless the fuel cap is securely tightened after
refueling.
Transport and storage
•
Store and transport the machine and fuel so that there
is no risk of any leakage or fumes coming into contact
with sparks or naked flames, for example, from
electrical machinery, electric motors, electrical relays/
switches or boilers.
•
When storing and transporting fuel always use
approved containers intended for this purpose.
Long-term storage
•
When storing the machine for long periods the fuel
tank must be emptied. Contact your local petrol
station to find out where to dispose of excess fuel.
English – 15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
Protective equipment
General safety precautions
This section describes basic safety directions for using
the machine. This information is never a substitute for
professional skills and experience.
General
•
Do not use the machine unless you are able to call for
help in the event of an accident.
•
Please read the operator’s manual carefully and make
sure you understand the instructions before using the
machine. It is recommended that first time operators
also obtain practical intsuction before using the
machine.
Personal protective equipment
You must use approved personal protective equipment
whenever you use the machine. Personal protective
equipment cannot eliminate the risk of injury but it will
reduce the degree of injury if an accident does happen.
Ask your dealer for help in choosing the right equipment.
•
•
Keep in mind that it is you, the operator that is
responsible for not exposing people or their property
to accidents or hazards.
The machine must be kept clean. Signs and stickers
must be fully legible.
WARNING! The use of products such as
cutters, grinders, drills, that sand or form
!
Always use common sense
material can generate dust and vapours
which may contain hazardous chemicals.
Check the nature of the material you
intend to process and use an appropriate
breathing mask.
It is not possible to cover every conceivable situation you
can face. Always exercise care and use your common
sense. If you get into a situation where you feel unsafe,
stop and seek expert advice. Contact your dealer, service
agent or an experienced user. Do not attempt any task
that you feel unsure of!
Long-term exposure to noise can result
in permanent hearing impairment.
Always use approved hearing protection.
Listen for warning signals or shouts
when you are wearing hearing
protection. Always remove your hearing
protection as soon as the engine stops.
WARNING! The machine can be a
dangerous tool if used incorrectly or
carelessly, which can cause serious or
fatal injury to the operator or others.
!
Never allow children or other persons
not trained in the use of the machine to
use or service it.
Always wear:
•
•
•
Approved protective helmet
Hearing protection
Never allow anyone else to use the
machine without first ensuring that they
have read and understood the contents
of the operator’s manual.
Approved eye protection. If you use a face shield then
you must also wear approved protective goggles.
Approved protective goggles must comply with
standard ANSI Z87.1 in the USA or EN 166 in EU
countries.Visors must comply with standard EN 1731.
Breathing mask
Never use the machine if you are
fatigued, while under the influence of
alcohol or drugs, medication or anything
that could affect your vision, alertness,
coordination or judgement.
•
•
•
Heavy-duty, firm grip gloves.
Tight-fitting, heavy-duty and comfortable clothing that
permits full freedom of movement. Cutting generates
sparks that can ignite clothing. Husqvarna
recommends that you wear flame-retardant cotton or
heavy denim. Do not wear clothing made of material
such as nylon, polyester or rayon. If ignited such
material can melt and cling to the skin. Do not wear
shorts
WARNING! Unauthorized modifications
and/or accessories may lead to serious
injury or death to the user or others.
Under no circumstances may the design
of the machine be modified without the
permission of the manufacturer.
!
•
Boots with steel toe-caps and non-slip sole.
Do not modify this product or use it if it
appears to have been modified by others.
Other protective equipment
CAUTION! Sparks may appear and start a
Never use a machine that is faulty. Carry
out the safety checks, maintenance and
service instructions described in this
manual. Some maintenance and service
measures must be carried out by trained
and qualified specialists. See instructions
under the Maintenance heading.
fire when you work with the machine.
Always keep fire fighting equipment
handy.
!
•
•
Fire Extinguisher
Always have a first aid kit nearby.
Always use genuine accessories.
16 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
Basic working techniques
WARNING! This machine produces an
electromagnetic field during operation.
This field may under some
!
WARNING! Do not pull the power cutter
to one side, this can cause the blade to
jam or break resulting in injury to people.
circumstances interfere with active or
passive medical implants.To reduce the
risk of serious or fatal injury, we
recommend persons with medical
implants to consult their physician and
the medical implant manufacturer before
operating this machine.
!
Under all circumstances avoid grinding
using the side of the blade; it will almost
certainly be damaged, break and can cause
immense damage. Only use the cutting
section.
Work area safety
Never use a diamond blade to cut plastic
material.The heat produced during cutting
may melt the plastic and it can stick to the
cutting blade and cause a kickback.
WARNING! The safety distance for the
power cutter is 15 metres (50 foot).You
are responsible to ensure that animals
and onlookers are not within the working
area. Do not start cutting until the
working area is clear and you are
standing firmly.
!
Cutting metal generates sparks that may
cause fire. Do not use the machine near
ignitable substances or gases.
•
The machine is designed and intended for cutting with
abrasive blades or diamond blades intended for high
speed handheld machines. The machine shall not be
used with any other type of blade, or for any other type
of cutting.
•
•
Observe your surroundings to ensure that nothing can
affect your control of the machine.
Ensure that no one/nothing can come into contact
with the cutting equipment or be hit by parts thrown by
the blade.
•
•
Check that the cutting blade is fitted correctly and
does not show signs of damage. See the instructions
in the sections "Cutting blades" and "Assembly and
settings".
Check that the correct cutting blade is used for the
application in question. See instructions in the section
"Cutting blades".
•
•
Do not use the machine in bad weather, such as
dense fog, heavy rain, strong wind, intense cold, etc.
Working in bad weather is tiring and can lead to
dangerous conditions, e.g. slippery surfaces.
Never start to work with the machine before the
working area is clear and you have a firm foothold.
Look out for any obstacles with unexpected
movement. Ensure when cutting that no material can
become loose and fall, causing injury to the
operator.Take great care when working on sloping
ground.
•
•
Never cut asbestos materials!
Hold the saw with both hands; keep a firm grip with
thumbs and fingers encircling the handles. The right
hand should be on the rear handle and the left hand
on the front handle. All operators, weather right or left
handed shall use this grip. Never operate a power
cutter holding it with only one hand.
•
•
•
Ensure that the working area is sufficiently illuminated
to create a safe working environment.
Make sure that no pipes or electrical cables are routed
in the working area or in the material to be cut.
If cutting into a container (drum, pipe, or other
container) you must first make sure it does not contain
flammable or other volatile material.
•
Stand parallel to the cutting blade. Avoid standing
straight behind. In the event of a kickback the saw will
move in the plane of the cutting blade.
English – 17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
•
•
•
Maintain a safe distance from the cutting blade when
the engine is running.
•
Move the blade slowly forwards and backwards to
achieve a small contact area between the blade and
the material to be cut.This reduces the temperature of
the blade and ensures effective cutting.
Never leave the machine unsupervised with the motor
running.
Never move the machine when the cutting equipment
is rotating. The machine is equipped with a friction
retarder to shorten the blade stop time.
•
The guard for the cutting equipment should be
adjusted so that the rear section is flush with the work
piece. Spatter and sparks from the material being cut
are then collected up by the guard and led away from
the user. The guards for the cutting equipment must
always be fitted when the machine is running.
Managing dust
The machine is fitted with DEX (Dust Extinguisher), a low
flushing water kit that offers maximum dust suppression.
Use wet cutting blades with DEX when possible for
optimal dust management. See instructions in the section
"Cutting blades".
Adjust water flow using the tap to bind the cutting dust.
The volume of water required varies depending on the
type of job at hand.
•
Never use the kickback zone of the blade for cutting.
See instructions under the heading "Kickback".
Keep a good balance and a firm foothold.
Never cut above shoulder height.
If water hoses loosen from their supply sources, this
indicates that the machine is connected to a water
pressure that is too high. See instructions under the
"Technical data" heading for recommended water
pressure.
•
•
•
Never cut from a ladder. Use a platform or scaffold if
the cut is above shoulder height. Do not overreach
Cutting with toothed/carbide tipped
blades during rescue operaions
WARNING! A power cutter should never
be used with carbide tipped blade for
non-emergency work, such as in the
construction trades.
!
Be aware at all times that carbide tipped
blades are more kickback prone than
abrasive or diamond blades if not used
properly.
•
•
Stand at a comfortable distance from the work piece.
Check that the blade is not in contact with anything
when the machine is started
If the public safety force (fire department) that purchased
this power cutter has decided to equip this unit with a
carbide tipped blade for rescue operations, the following
safety considerations must be adhered to.
•
Apply the cutting blade gently with high rotating speed
(full throttle) Maintain full speed until cutting is
complete.
Training and protective equipment
•
•
Let the machine work without forcing or pressing the
blade.
•
Only operators trained in the use of cutting with a
power cutter equipped with carbide tipped blade shall
be allowed to operate the power cutter.
Feed down the machine in line with the blade.
Pressure from the side can damage the blade and is
very dangerous.
•
•
Full protective fire fighting gear shall be worn by the
operator at all times.
A full face shield (not just protective eye glasses) shall
be worn by the operator to protect the face from flying
debris or a sudden kick-back of the power cutter.
18 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
Risk area
Before each rescue operation
No persons that do not have the protective equipment
described above shall be allowed inside the risk area for
thrown material.
Check that the blade and the blade guard is not damaged
or cracked. Replace the blade or the blade guard if it has
been exposed to impact or is cracked.
•
Check that no carbide tips have loosened from the
cutting blade.
•
Check that the blade is not skew or shows signs of
cracking or other defects.
When cutting in hard materials carbide tipped blades will
rapidly lose its sharpness. For best performance during
rescue operations we recommend that a new blade be
installed.
Kickback
20 m (66 ft)
WARNING! Kickbacks are sudden and
can be very violent.The power cutter can
be thrown up and back towards the user
in a rotating motion causing serious or
even fatal injury. It is vital to understand
what causes kickback and how to avoid it
before using the machine.
!
Blade speed
Apply the cutting blade gently with high rotating speed
(full throttle) Maintain full speed until cutting is complete.
Low blade speed, especially in hard and thin materials
can result in jamming and the breaking-off of the carbide
tips.
Kickback is the sudden upward motion that can occur if
the blade is pinched or stalled in the kickback zone. Most
kickbacks are small and pose little danger. However a
kickback can also be very violent and throw the power
cutter up and back towards the user in a rotating motion
causing serious or even fatal injury.
Thin material
Cutting thin and hard material (i.e. a sheet metal covered
roof) should be conducted in a forward direction for best
control.
Pinching or jamming
Make a careful evaluation of how the object will move
during the final stage of the cutting to avoid pinching or
jamming. The cut must open during the cut. If the object
sags and the cut begins to close the blade may pinch,
possibly resulting in a kick-back or damage to the blade.
Reactive force
A reactive force is always present when cutting.The force
pulls the machine in the opposite direction to the blade
rotation. Most of the time this force is insignificant. If the
blade is pinched or stalled the reactive force will be strong
and you might not be able to control the power cutter.
Cutting in line
Skewing or twisting in the line of cut will reduce cutting
efficiency and damage the blade.
Never move the machine when the cutting equipment is
rotating. Gyroscopic forces can obstruct the intended
movement.
English – 19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
Kickback zone
Pipe cutting
Never use the kickback zone of the blade for cutting. If
the blade is pinched or stalled in the kickback zone, the
reactive force will push the power cutter up and back
towards the user in a rotating motion causing serious or
even fatal injury.
Special care should be taken when cutting in pipes. If the
pipe is not properly supported and the cut kept open
through out the cutting, the blade might be pinched in the
kickback zone and cause a severe kickback. Be
especially alert when cutting a pipe with a belled end or a
pipe in a trench that, if not properly supported, may sag
and pinch the blade.
Before starting the cut the pipe must be secure so it does
not move or roll during cutting.
Climbing kickback
If the kickback zone is used for cutting the reactive force
drives the blade to climb up in the cut. Do not use the
kickback zone. Use the lower quadrant of the blade to
avoid climbing kickback.
If the pipe is allowed to sag and close the cut, the blade will be
pinched in the kick back zone and a severe kick back might
develop.If the pipe is properly supported the end of the pipe will
move downward, the cut will open and no pinching will occur.
Pinching kickback
Pinching is when the cut closes and pinches the blade. If
the blade is pinched or stalled the reactive force will be
strong and you might not be able to control the power
cutter.
Proper sequence cutting a pipe
1
2
3
First cut section I.
Move to side II and cut from section I to bottom of the pipe.
Move to side III and cut the remaining part of the pipe
ending at the bottom.
I
III
II
If the blade is pinched or stalled in the kickback zone, the
reactive force will push the power cutter up and back
towards the user in a rotating motion causing serious or
even fatal injury. Be alert for potential movement of the
work piece. If the work piece is not properly supported
and shifts as you cut, it might pinch the blade and cause
a kick back.
20 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING
How to aviod kickback
Avoiding kickback is simple.
•
The work piece must always be supported so that the
cut stays open when cutting through. When the cut
opens there is no kickback. If the cut closes and
pinches the blade there is always a risk of kickback.
•
•
Take care when inserting the blade in an existing cut.
Be alert to movement of the work piece or anything
else that can occur, which could cause the cut to close
and pinch the blade.
Transport and storage
•
•
•
•
•
Secure the equipment during transportation in order
to avoid transport damage and accidents.
Do not store or transport the power cutter with the
cutting blade fitted.
For transport and storage of cutting blades, see the
section "Cutting blades".
For transport and storage of fuel, see the section
"Fuel handling".
Store the equipment in a lockable area so that it is out
of reach of children and unauthorized persons.
English – 21
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
Before starting
WARNING! Note the following before
starting: Please read the operator’s manual
carefully and make sure you understand the
instructions before using the machine.
!
•
Press the air purge diaphragm repeatedly until fuel
begins to fill the diaphragm (about 6 times). The
diaphragm need not be completely filled.
Wear personal protective equipment. See
under heading ”Personal protective
equipment”.
Do not start the machine without the belt
and belt guard fitted. Otherwise the clutch
could come loose and cause personal
injuries.
Check that the fuel cap is properly secured,
and that there is no fuel leakage.
Make sure no unauthorised persons are in
the working area, otherwise there is a risk of
serious personal injury.
•
Grip the front handle with your left hand.Put your right
foot on the lower section of the rear handle pressing
the machine against the ground. Pull the starter
handle with your right hand until the engine starts.
Never twist the starter cord around your hand.
•
Perform daily maintenance. See instructions in the
section "Maintenance".
Starting
WARNING! The cutting blade rotates
when the engine is started. Make sure it
can rotate freely.
!
With a cold engine:
•
Make sure that the stop switch (STOP) is in the left
position.
•
•
Push in the choke control as soon as the engine
starts, with the choke pulled out the engine will stop
after a few seconds. (If the engine stops anyway, pull
the starter handle again.)
Press the throttle trigger to disengage the start throttle
and the machine will idle.
•
•
Start throttle position and choke is obtained by pulling
out the choke control completely.
NOTICE! Pull with your right hand out the starter cord
slowly until you feel a resistance (as the starter pawls
engage) and then pull firmly and rapidly.
Decompression valve: Press in the valve to reduce
the pressure in the cylinder, this is to assist starting
the power cutter. The decompression valve should
always be used when starting. The valve
automatically returns to its initial position when the
machine starts.
Do not pull the starter cord all the way out and do not let
go of the starter handle when the cord is fully extended.
This can damage the machine.
22 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
With a warm engine:
WARNING! When the engine is running
the exhaust contains chemicals such as
unburned hydrocarbons and carbon
monoxide.The content of the exhaust
fumes is known to cause respiratory
problems, cancer, birth defects or other
reproductive har
!
•
Make sure that the stop switch (STOP) is in the left
position.
Carbon monoxide is colorless and
tasteless and is always present in
exhaust fumes.The onset of carbon
monoxide poisoning is distinguished by
a slight dizziness which may or may not
be recognized by the victim. A person
may collapse and lapse into
unconsciousness with no warning if the
concentration of carbon monoxide is
sufficiently high. Since carbon monoxide
is colorless and odorless, its presence
can not be detected. Any time exhaust
odors are noticed, carbon monoxide is
present. Never use a petrol powered
power cutter indoors or in trenches more
than 3 foot (1 meter) deep or in other
areas with poor ventilation. Ensure
proper ventilation when working in
trenches or other confined areas.
•
•
Set the choke control in the choke position.The choke
position is also the automatic start throttle position.
Decompression valve: Press in the valve to reduce
the pressure in the cylinder, this is to assist starting
the power cutter. The decompression valve should
always be used when starting. The valve
automatically returns to its initial position when the
machine starts.
Stopping
CAUTION!The cutting blade continues to
•
•
Push the choke control to disable the choke (the start
throttle position remains).
rotate up to a minute after the motor has
stopped. (Blade coasting.) Make sure
that the cutting blade can rotate freely
until it is completely stopped.
Carelessness can result in serious
personal injury.
!
Grip the front handle with your left hand.Put your right
foot on the lower section of the rear handle pressing
the machine against the ground. Pull the starter
handle with your right hand until the engine starts.
Never twist the starter cord around your hand.
•
Stop the engine by moving the stop switch (STOP) to
the right.
•
Press the throttle trigger to disengage the start throttle
and the machine will idle.
NOTICE! Pull with your right hand out the starter cord
slowly until you feel a resistance (as the starter pawls
engage) and then pull firmly and rapidly.
Do not pull the starter cord all the way out and do not let
go of the starter handle when the cord is fully extended.
This can damage the machine.
English – 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
General
WARNING! The user must only carry out
the maintenance and service work
described in this Operator's Manual.
More extensive work must be carried out
by an authorized service workshop.
!
The engine should be switched off, and
the stop switch in STOP position.
Wear personal protective equipment. See
under heading ”Personal protective
equipment”.
The life span of the machine can be
reduced and the risk of accidents can
increase if machine maintenance is not
carried out correctly and if service and/or
repairs are not carried out professionally.
If you need further information please
contact your nearest service workshop.
•
Let your Husqvarna dealer regularly check the machine and make essential adjustments and repairs.
Maintenance schedule
In the maintenance schedule you can see which parts of your machine that require maintenance, and with which
intervals it should take place.The intervals are calculated based on daily use of the machine, and may differ depending
on the rate of usage.
Daily maintenance
Cleaning
Weekly maintenance
Cleaning
Monthly maintenance
Cleaning
External cleaning
Cooling air intake
Spark plug
Fuel tank
Functional inspection
General inspection
Throttle lockout*
Stop switch*
Functional inspection
Vibration damping system*
Muffler*
Functional inspection
Fuel system
Air filter
Drive belt
Drive gear, clutch
Blade guard*
Carburettor
Cutting blade**
Starter
*See instructions in the section "Machine’s safety equipment".
** See instructions in the section "Cutting blades" and "Assembly and settings".
24 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Cleaning
Functional inspection
External cleaning
General inspection
•
Clean the machine daily by rinsing it with clean water
after the work is finished.
•
Check that nuts and screws are tight.
Drive belt
Cooling air intake
Check the tension of the drive belt
•
Clean the cooling air intake when needed.
•
For correct tensioning of the drive belt, the square nut
should be positioned opposite the marking on the belt
cover.
NOTICE! A dirty or blocked air intake results in the
machine overheating which causes damage to the
piston and cylinder.
Tensioning the drive belt
•
The tension of a new drive belt must be readjusted
after one or two tanks of fuel have been used.
Spark plug
•
When the machine is equipped with a friction retarder,
a scraping sound can be heard from the bearing
housing when the blade is turned by hand. This is
quite normal. Please contact an accredited
•
If the machine is low on power, difficult to start or runs
poorly at idle speed: always check the spark plug first
before taking other steps.
Husqvarna workshop if you have any questions.
•
•
Ensure that the spark plug cap and ignition lead are
undamaged to avoid the risk of electric shock.
•
•
The drive belt is enclosed and well protected from
dust and dirt.
If the spark plug is dirty, clean it and at the same time
check that the electrode gap is 0.5 mm. Replace if
necessary.
When the drive belt is to be tensioned, release the
bolts holding the cutting arm.
NOTICE! Always use the recommended spark plug
type! Use of the wrong spark plug can damage the
piston/cylinder.
•
Screw the adjuster screw so that the square headed
nut comes opposite the marking on the cover. This
automatically ensures that the belt has the correct
tension.
These factors cause deposits on the spark plug
electrodes, which may result in operating problems and
starting difficulties.
•
An incorrect fuel mixture (too much or incorrect type
of oil).
•
A dirty air filter.
•
Tighten both of the screws holding the cutting head
using a combination spanner.
English – 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Replacing the drive belt
Carburettor
The carburettor is equipped with fixed needles to ensure
WARNING! Never start the engine when
the machine always receives the correct mixture of fuel
and air. When the engine lacks power or accelerates
poorly, do the following:
the belt pulley and clutch are removed
for maintenance. Do not start the
machine without the cutting arm or
cutting head fitted. Otherwise the clutch
could come loose and cause personal
injuries.
!
•
Check the air filter and replace if necessary.When this
does not help, contact an authorised service
workshop.
Adjusting the idle speed
•
First release the two bolts and then the adjuster screw
to release the belt tension.
CAUTION! Contact your dealer/service
workshop, if the idle setting cannot be
adjusted so that the blades are
stationary. Do not use the machine until
it has been properly adjusted or repaired.
!
Start the engine and check the idling setting. When the
carburettor is set correctly the cutting blade should be still
while engine is idling.
•
•
•
Now unscrew the bolts and dismantle the belt guard.
•
Adjust the idle speed using the T screw. When an
adjustment is necessary, first turn the screw clockwise
until the blade starts to rotate. Now turn the screw
anti-clockwise until the blade stops rotating.
T
Remove the belt from the belt pulley.
Rec. idle speed: 2700 rpm
The cutting head is now loose and can be removed
from the machine. Remove the rear belt guard by
releasing the two screws holding the guard.
•
•
Replace the drive belt.
Assemble in the reverse order as set out for
dismantling.
26 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
•
Secure the starter cord around the cord pulley as
Starter
illustrated. Tighten the fastening well and ensure that
the free end is as short as possible. Secure the end of
the starter cord in the starter handle.
WARNING! When the recoil spring is
wound up in the starter housing it is
under tension and can, if handled
carelessly, pop out and cause personal
injury.
!
Always be careful when changing the
recoil spring or the starter cord. Always
wear protective goggles.
Tensioning the recoil spring
Changing a broken or worn starter cord
•
Guide the cord through the cut-out in the periphery of
the pulley and wind the cord 3 times clockwise around
the centre of the starter pulley.
•
Loosen the screws that hold the starter against the
crankcase and remove the starter.
•
Now pull the starter handle and in doing so tension the
spring.Repeat the procedure once more, but this time
with four turns.
•
Pull the cord out about 30 cm and lift it into the cut-out
in the periphery of the starter pulley.When the cord is
intact: Release the spring tension by letting the pulley
rotate slowly backwards.
•
•
Note that the starter handle is drawn to its correct
home position after tensioning the spring.
Check that the spring is not drawn to its end position
by pulling out the starter line fully. Slow the starter
pulley with your thumb and check that you can turn the
pulley at least a further half turn.
•
Remove any remnants of the old starter cord and
check that the return spring works. Insert the new
starter cord through the hole in the starter housing
and in the cord pulley.
English – 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Changing a broken recoil spring
Fuel system
•
Undo the bolt in the centre of the pulley and remove
the pulley.
General
•
•
Check that the fuel cap and its seal are not damaged.
Check the fuel hose. Replace when damaged.
Fuel filter
•
•
The fuel filter sits inside the fuel tank.
The fuel tank must be protected from contamination
when filling. This reduces the risk of operating
disturbances caused by blockage of the fuel filter
located inside the tank.
•
The filter cannot be cleaned but must be replaced with
a new filter when it is clogged. The filter should be
changed at least once per year.
•
•
Bear in mind that the return spring lies tensioned in
the starter housing.
Loosen the bolts holding the spring cassette.
Air filter
The air filter only needs to be checked if the engine drops
in power.
•
Loosen the screws. Remove the air filter cover.
•
Remove the recoil spring by turning the starter over
and loosen the hooks, with the help of a screwdriver.
The hooks hold the return spring assembly on the
starter.
•
Check the air filter and replace if necessary.
Replacing the air filter
NOTICE! The air filter must not be cleaned or blown
clean with compressed air. This will damage the filter.
•
Loosen the screws. Remove the cover.
•
Lubricate the recoil spring with light oil. Fit the pulley
and tension the recoil spring.
Fitting the starter
•
To fit the starter, first pull out the starter cord and place
the starter in position against the crankcase. Then
slowly release the starter cord so that the pulley
engages with the pawls.
•
Replace the air filter.
Drive gear, clutch
•
Check the clutch centre, drive gear and clutch spring
for wear.
•
Tighten the screws.
28 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Technical data
Technical data
K760, K760 Rescue
Engine
Cylinder displacement, cm3
74
Cylinder bore, mm
51
Stroke, mm
36
Idle speed, rpm
2700
Wide open throttle - no load, rpm
Power, kW/ rpm
9300 (+/- 150)
3,7/9000
Ignition system
Manufacturer of ignition system
Type of ignition system
Spark plug
SEM
CD
Champion RCJ 6Y/NGK BPMR 7A
0,5
Electrode gap, mm
Fuel and lubrication system
Manufacturer of carburettor
Carburettor type
Zama
C3
Fuel tank capacity, litre
Water cooling
0,9
Recommended water pressure, bar
0,5-10
Weight
12” (300 mm)
14” (350 mm)
Power cutter without fuel and cutting blade, kg
9.6
9.8
Noise emissions (see note 1)
Sound power level, measured dB (A)
Sound power level, guaranteed LWA dB (A)
Sound levels (see note 2)
113
115
113
115
Equivalent sound pressure level at the operator’s ear, dB(A) 101
101
Equivalent vibration levels, a hveq (see note 3)
Front handle, m/s2
Rear handle, m/s2
<2,5
<2,5
<2,5
<2,5
Note 1: Noise emissions in the environment measured as sound power (L ) in conformity with EC directive 2000/14/EC.The
WA
difference between guaranteed and measured sound power is that the guaranteed sound power also includes dispersion in
the measurement result and the variations between different machines of the same model according to Directive 2000/14/EC.
Note 2: Equivalent sound pressure level, according to EN ISO 19432, is calculated as the time-weighted energy total for
different sound pressure levels under various working conditions. Reported data for equivalent sound pressure level for the
machine has a typical statistical dispersion (standard deviation) of 1 dB (A).
Note 3: Equivalent vibration level, according to EN ISO 19432, is calculated as the time-weighted energy total for vibration
levels under various working conditions. Reported data for equivalent vibration level has a typical statistical dispersion
2
(standard deviation) of 1 m/s .
Cutting equipment
Max cutting depth, Max. peripheral
Max. speed of output Max blade thickness,
Cutting blade
mm
100
125
speed, m/s
shaft, rpm
mm
12” (300 mm)
14” (350 mm)
80
90
4700
5
4700
5
English – 29
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
EC-declaration of conformity
(Applies to Europe only)
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares under sole responsibility that the power
cutters Husqvarna K760, K760 Rescue from 2013’s serial numbers and onwards (the year is clearly stated in plain text
on the rating plate with subsequent serial number), complies with the requirements of the COUNCIL’S DIRECTIVES:
•
•
•
of May 17, 2006 ”relating to machinery” 2006/42/EC
of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.
of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. Conformity assessment according
to Annex V.
For information relating to noise emissions, see the Technical data chapter.
The following standards have been applied: EN ISO 12100:2010, ISO 14982:1998, EN ISO 19432:2012.
Notified body:0404, SMP Svensk Maskinprovning AB, Box 7035, SE-750 07 Uppsala, Sweden, has performed voluntary
type examination in accordance with the machinery directive (2006/42/EC) on behalf of Husqvarna AB. The certificate
has the number: SEC/10/2285.
In addition, SMP, Svensk Maskinprovning AB, Box 7035, SE-750 07 Uppsala, Sweden, has certified conformity with
annex V of the Council’s Directive of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. The
certificate has the number: 01/169/031 -K760, K760 Rescue
Gothenburg, 18 Februari 2013
Helena Grubb
Vice President, Construction Equipment Husqvarna AB
(Authorized representative for Husqvarna AB and responsible for technical documentation.)
30 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
GB - Original instructions
1155019-26
´®z+W!|¶6-¨
´®z+W!|¶6-¨
2013-02-19
Download from Www.Somanuals.com. All Manuals Search And Download.
|