For Your Records and Warranty
Assistance
Model Name: _____________________
Catalog/Model No.: ________________
Serial No.: ________________________
Date Purchased: ___________________
Where Purchased: _________________
For reference also attach your receipt or a
copy of your receipt to the manual.
TYPE 2 Models
42641-01 • 09/13/07
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer’s Choice and Optional Accessories
Support Brace
Understanding Mounting and Installer’s Choice®
Hunter’s patented 3-position mounting system provides you maximum
installation flexibility and ease. You can install your Hunter fan in one
of three ways, depending on ceiling height and your preference: Low
Profile, Standard, or Angled mounting. e steps in this manual include
instructions for all three Installer’s Choice mounting methods.
Low Profile
Mounting
Style
Ceiling
Outlet
Box
10”
Considering Optional Accessories
Low Profile Mounting fits close to the
ceiling, recommended for ceilings less than 8
feet high
Consider using Hunter’s optional accessories, including a wall-mounted
or remote speed control. To install and use the accessories, follow
the instructions included with each product. For quiet and optimum
performance of your Hunter fan, use only Hunter speed controls.
Support Brace
Standard
Ceiling
Mounting
Outlet
Style
Box
For ceilings higher than 8 feet, you
can purchase Hunter extension
downrods. All Hunter fans use sturdy
3/4” diameter pipe to assure stability
and wobble-free performance.
12”
3
Standard Mounting hangs from the ceiling
by a downrod (included), recommended for
ceilings 8 feet or higher
Support Brace
Ceiling
Outlet
Box
Angle
Mounting
Style
Angled Mounting recommended for a
vaulted or angled ceiling
42641-01 • 09/13/07
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
1 • Getting Ready
To install a ceiling fan, be sure you can do the following:
• Locate the ceiling joist or other suitable support in ceiling.
• Drill holes for and install wood screws.
• Identify and connect electrical wires.
• Lift 40 pounds.
If you need help installing the fan, your Hunter fan dealer can direct
you to a licensed installer or electrician.
Gathering the Tools
You will need the following tools for installing the fan:
• Electric drill with 9/64” bit
• Standard screwdriver (magnetic tip recommended)
• Phillips-head screwdriver (magnetic tip recommended)
• Wrench or pliers
• Ladder (height dependent upon installation site)
Installing Multiple Fans?
4
Checking Your Fan Parts
If you are installing more than
one fan, keep the fan blades and
blade irons (if applicable) in sets,
as they were shipped.
Carefully unpack your fan to avoid damage to the fan parts. Refer to
the included Parts Guide. Check for any shipping damage to the motor
or fan blades. If any parts are missing or damaged, contact your Hunter
dealer or call Hunter Technical Support Department at 888-830-1326.
Preparing the Fan Site
Before you begin installing the fan, follow all the instructions in
the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan
location and attachment to the building structure are essential for
safety, reliable operation, maximum efficiency, and energy savings.
Hunter Fan Company
42641-01 • 09/13/07
Download from Www.Somanuals.com. All Manuals Search And Download.
2 • Installing the Ceiling Plate
CAUTION: To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to the outlet box
and associated wall switch location. If you cannot lock the circuit breakers
in the off position, securely fasten a prominent warning device, such as a
tag, to the service panel.
Toward
Ceiling Peak
2-1. Drill two pilot holes into the wood support structure through the
outermost holes in the outlet box. e pilot holes should be 9/64”
in diameter.
For Angled Ceilings: Be sure to orient the ceiling plate so that the
two tabs are pointing toward the ceiling peak.
For Angled Ceilings: Be sure to orient
the ceiling plate so that the two tabs
are pointing toward the ceiling peak.
2-2. Your fan comes with four preinstalled noise isolators. Check to
make sure all four isolators are in place and were not removed
during shipment.
2-3. Place a flat washer on each of the two 3” wood screws.
2-4. read the supply wires from the outlet box in the ceiling through
the hole in the center of the ceiling plate.
5
2-5. Align the slotted holes in the ceiling plate with the pilot holes you
drilled in the wood support structure. For proper alignment use
slotted holes directly across from each other.
Note: e isolators should be flush against the ceiling.
2-6. Pass the screws through the slotted holes in the ceiling plate into
the pilot holes you drilled.
Tighten the screws into the 9/64” pilot holes; do not use lubricants
on the screws. Do not over tighten.
Ceiling
Plate
Flat Washer
3” Wood
Steps 2-3 – 2-6
Screw
42641-01 • 09/13/07
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
3 • Assembling the Fan
WARNING: Fan may fall if not assembled as directed in these
installation instructions.
Standard or Angled Mounting
Steps 3-2 – 3-3
3-1. Unbundle the wires from the fan.
For Standard or Angled mounting:
Downrod
3-2. Insert the downrod through the canopy and canopy trim ring.
Feed the wires from the fan through the downrod on one side of
the pin in the ball.
Canopy
3-3. Loosen the square head set screw on the adapter to install the
pipe and ball assembly. Note: When the pipe and ball assembly
is fully installed, 2-3 threads on the pipe will still be visible; this is
normal. Securely retighten the set screw with a wrench or pliers.
Go to 4 • Hanging and Wiring the Fan.
Canopy
Trim Ring
Set Screw
CAUTION: e adapter has a special coating on the threads. Do
not remove this coating; the coating prevents the downrod from
unscrewing. Once assembled, do not remove the downrod.
For Low Profile mounting:
6
Note: For low profile mounting, the downrod is replaced with the
low profile washer.
Low Profile Mounting
Steps 3-5 – 3-6
Low Profile
Screws
3-4. Remove the set screw from the adapter.
3-5. Place the low profile washer into the canopy with the lip down.
Low Profile
Washer
Green
Ground
Wire
3-6. Align the holes in the washer with the holes in the adapter.
Assemble securely with three low profile screws.
Go to 4 • Hanging and Wiring the Fan.
Canopy
Trim Ring
Step 3-6 (Detail)
Adapter
Canopy
Low Profile Screw
Low Profile
Washer
Low Profile Screw
Hunter Fan Company
42641-01 • 09/13/07
Download from Www.Somanuals.com. All Manuals Search And Download.
4 • Hanging and Wiring the Fan
4-1. Raise the fan and align the slots in the canopy with the hooks on the
ceiling plate.
Note: To hang the fan, you must tilt the canopy to an almost vertical
position so that the canopy slots sit on the ceiling plate hooks.
Wire
connector
All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualified electrician.
Wall switches are not included. Select an acceptable general-use switch in
accordance with national and local electrical codes.
Single Switch Wiring
4-2. Make sure the power to the outlet box and associated wall switch
location is still OFF.
4-3. To connect the wires, hold the bare metal leads together and place a
wire connector over them, then twist the wire connector clockwise
until tight.
4-4. Connect the bare or green ground wired (grounded) from the ceiling
to the green ground wire (grounded) from the ceiling plate and the
green ground wire from the fan.
7
4-5. Connect the white wire (ungrounded) from the ceiling to the white
wired (ungrounded) from the fan.
4-6. Connect the remaining wires as follows:
Single Switch Wiring:
Dual Switch Wiring
• e black wire from the ceiling to the black and the black/white
wire from the fan.
Dual Switch Wiring:
• e black wire from the ceiling to the black wire from the fan.
• e black/white wire from the fan to the wire for the wall switch.
CAUTION: Be sure no bare wire or wire strands are visible after making
connections.
4-7 Turn the splices upward and push them carefully back through the
ceiling plate into the outlet box.
4-8 Spread the wires apart, with the grounded wires on one side of the
outlet box and the ungrounded wires on the other side of the outlet
box.
42641-01 • 09/13/07
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
5 • Installing the Canopy and Canopy Trim Ring
WARNING: Failure to complete the following steps could cause the fan
Step 5-1
to fall.
Note: It is recommended you use a magnetic tip screwdriver for the
following steps.
Tab
5-1. Rotate the hanger ball so the tab in the canopy is secure in the
hanger ball groove. Note: Your fan may have multiple tabs and
grooves that must be aligned.
Groove
5-2. Swing the fan up to align the canopy screw holes with the
mounting holes on the ceiling plate.
Step 5-2
WARNING: e slots in the canopy must remain engaged while
swinging the canopy for alignment.
5-3. Holding the canopy up with the screw holes aligned, partially
install two canopy screws into the holes opposite the ceiling plate
tabs.
5-4. Partially install a canopy screw between the slots in the canopy.
When all the holes are properly aligned, securely tighten all three
canopy screws.
8
5-5. Verify that the tabs in the canopy are still in the grooves of the
hanger ball.
Step 5-3
5-6. Align the tabs on the trim ring opposite the grooves in the hanger
ball. Using both hands, push the canopy trim ring up to the top of
the canopy. e canopy trim ring will snap and lock into place.
Canopy
Note: Should you need to remove the trim ring, press firmly on
opposite sides of the trim ring directly above the groove in the
hanger ball. e tabs will flex out releasing the canopy trim ring.
Canopy
Trim
Ring
Canopy Screw
Hunter Fan Company
42641-01 • 09/13/07
Download from Www.Somanuals.com. All Manuals Search And Download.
6 • Assembling the Blades
Hunter fans use several styles of fan blade irons (brackets that hold the
blade to the fan).
6-1. Your fan may include blade grommets. If your fan has grommets,
insert them by hand into the holes on the blades.
Step 6-1 (Detail)
6-2. Attach each blade to a blade iron using three blade assembly
screws. If you used grommets, the blades may appear slightly loose
after screws are tightened. is is normal.
6-3. Some blade mounting screws are installed in the motor to
secure shipping blocks. Remove the blade mounting screws and
rubber bumpers from the motor. Save the screws and discard the
bumpers.
Grommet
6-4. For each blade, insert one blade mounting screw through the
blade iron, and attach lightly to the fan. Insert the second blade
mounting screw, then securely tighten both mounting screws.
Steps 6-1 – 6-2
Blade Assembly
Screws
9
Use with grommet
Use without grommet
Blade
Mounting
Screw
42641-01 • 09/13/07
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
7 • Completing Your Installation with a Light Fixture
Your Hunter fan comes with an integrated light fixture assembly.
WARNING: Use only the light fixture supplied with this fan model.
7-1. To attach the upper switch housing, partially install two #6-32 x
3/8” housing assembly screws into the switch housing mounting
plate.
7-2. Feed the upper plug connector through the center opening of the
housing.
7-3. Align the keyhole slots in the housing with the housing assembly
screws.
7-4. Turn the housing counterclockwise until the housing assembly
screws are firmly situated in the narrow end of the keyhole slots.
Install the remaining #6-32 x 3/8” screw into the housing. Tighten
all three screws firmly.
Steps 7-1 – 7-3
Housing
Upper
Switch
Housing
Assembly
Screw
CAUTION: Make sure the upper switch housing is securely
attached to the switch housing mounting plate. Failure to properly
attach and tighten all three assembly screws could result in the
switch housing and/or light fixture falling.
10
Step 7-4
Hunter Fan Company
42641-01 • 09/13/07
Download from Www.Somanuals.com. All Manuals Search And Download.
7-5. To attach the lower switch housing, connect the upper plug
connector from the motor to the lower plug connector in the
lower switch housing assembly.
Note: Both plug connectors are polarized and will only fit together
one way. Make sure the connectors are properly aligned before
connecting them. Incorrect connection could cause improper
operation and damage to the product.
Plug
Connector
7-6. Place the lower switch housing assembly over the upper switch
housing. Align the side screw holes in the upper and lower switch
housings. Attach the lower switch housing to the upper switch
housing
Steps 7-5 – 7-6
Lower Switch
Housing
7-7. To install each shade, first loosen the three thumbscrews.
7-8. Raise the shade to the light fixture. Tighten the thumbscrews
securely.
Plug
Connector
Detail
7-9. Install three B10 candelabra light bulbs (60 Watt maximum each).
11
Note: Glass shade style may vary.
Housing
Assembly Screw
umbscrews
Shade
Bulb
Steps 7-7 – 7-9
42641-01 • 09/13/07
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
8 • Operating and Cleaning Your Ceiling Fan
8-1. Turn on electrical power to the fan.
8-2. e fan pull chain controls power to the fan. e pull chain has
four settings in sequence: High, Medium, Low and Off.
• Pull the chain slowly to change settings.
• Release slowly to prevent the chain from recoiling into the
blades.
• e chain uses a breakaway connector that separates if the
chain is jerked. If this happens, simply reinsert the chain into
the connector.
8-3. e light pull chain controls power to the light. e pull chain has
two settings: On and Off.
In warm weather, use
downward air flow pattern
8-4. Ceiling fans work best by blowing air downward (counterclockwise
blade rotation) in warm weather to cool the room with a direct
breeze. In cold weather, having the fan draw air upward (clockwise
blade rotation) will distribute the warmer air trapped at the
ceiling around the room without causing a draft.
12
8-5. For cleaning finishes, use a soft brush or lint-free cloth to prevent
scratching. A vacuum cleaner brush nozzle can remove heavier
dust. Remove surface smudges or accumulated dirt and dust using
a mild detergent and a slightly dampened cloth. You may use
an artistic agent, but never abrasive cleaning agents as they will
damage the finish.
8-6. Clean wood finish blades with a furniture polishing cloth.
Occasionally, apply a light coat of furniture polish for added
protection and beauty. Clean painted and high-gloss blades in the
same manner as the fan finish.
In cold weather, use upward
air flow pattern
To Change Airflow Direction
Turn the fan off and let it come to a complete
stop. Slide the reversing switch on the fan to the
opposite position. Restart fan.
Reversing
Switch
Hunter Fan Company
42641-01 • 09/13/07
Download from Www.Somanuals.com. All Manuals Search And Download.
9 • Troubleshooting
Problem: Nothing happens; fan does not move.
1. Turn power on, replace fuse, or reset breaker.
2. Loosen canopy, check all connections according to the wiring the
fan section.
3. Check the plug connection in the switch housing.
4. Push motor reversing switch firmly left or right to ensure that the
switch is engaged.
5. Pull the pull chain to ensure it is on.
6. Remove the shipping bumpers.
Problem: Noisy operation.
1. Tighten the blade bracket screws until snug.
2. Tighten the blade screws until snug.
3. Check to see if the blade is cracked. If so, replace all the blades.
4. Change to an approved speed control.
5. Be sure that the glass is secure.
6. Check and tighten the screws in the switch housing mounting
plate and in the upper and lower switch housing.
13
Problem: Excessive wobbling.
1. If your fan wobbles when operating, use the enclosed balancing kit
and instructions to balance the fan.
2. Tighten all blade and/or blade iron screws.
3. Turn power off, support fan very carefully, and check that the
hanger ball is properly seated.
If you need parts or service assistance, please call
888-830-1326 or visit us at our Web site at
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114
42641-01 • 09/13/07
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
|