For Your Records and Warranty
Assistance
Model Name: _____________________
Catalog/Model No.: ________________
Serial No.: _______________________
Date Purchased: ___________________
Where Purchased: _________________
For reference also attach your receipt or a
copy of your receipt to the manual.
41936-01 • 11/18/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Installer’s Choice and Optional Accessories
Understanding Mounting and Installer’s Choice®
Hunter’s patented 3-position mounting system provides you maximum
installation flexibility and ease. You can install your Hunter fan in one
of three ways, depending on ceiling height and your preference: Low
Profile, Standard, or Angle mounting. e steps in this manual include
instructions for all three Installer’s Choice mounting methods.
Low Profile Mounting fits close to the
ceiling, recommended for ceilings less
than 8 feet high
Considering Optional Accessories
Consider using Hunter’s optional accessories, including a wall-mounted
or remote speed control. To install and use the accessories, follow
the instructions included with each product. For quiet and optimum
performance of your Hunter fan, use only Hunter speed controls.
Use the 3 inch downrod for ceilings
between 8 and 9 feet. Use the 6 inch
downrod for ceilings higher than 9
feet. No downrod required for ceilings
less than 8 feet (low profile).
Standard Mounting hangs from
the ceiling by a downrod (included),
recommended for ceilings 8 feet or higher
3
For ceilings higher than 10 feet, you
can purchase Hunter extension
downrods. All Hunter fans use sturdy
3/4” diameter pipe to assure stability
and wobble-free performance.
Angle Mounting recommended for a
vaulted or angled ceiling
41936-01 • 11/18/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
1 • Getting Ready
To install a ceiling fan, be sure you can do the following:
• Locate the ceiling joist or other suitable support in ceiling.
• Drill holes for and install wood screws.
• Identify and connect electrical wires.
• Lift 40 pounds.
If you need help installing the fan, your Hunter fan dealer can direct
you to a licensed installer or electrician.
Gathering the Tools
You will need the following tools for installing the fan:
• Electric drill with 9/64” bit
• Standard screwdriver (magnetic tip recommended)
• Phillips-head screwdriver (magnetic tip recommended)
• Wrench or pliers
• Ladder (height dependent upon installation site)
Checking Your Fan Parts
Installing Multiple Fans?
4
Carefully unpack your fan to avoid damage to the fan parts. Refer to
the included Parts Guide. Check for any shipping damage to the motor
or fan blades. If any parts are missing or damaged, contact your Hunter
dealer or call Hunter Technical Support Department at 888-830-1326.
If you are installing more than
one fan, keep the fan blades and
blade irons (if applicable) in sets,
as they were shipped.
Preparing the Fan Site
Before you begin installing the fan, follow all the instructions in
the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan
location and attachment to the building structure are essential for
safety, reliable operation, maximum efficiency, and energy savings.
Hunter Fan Company
41936-01 • 11/18/05
Download from Www.Somanuals.com. All Manuals Search And Download.
2 • Installing the Ceiling Plate
CAUTION: To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to the outlet box
and associated wall switch location. If you cannot lock the circuit breakers
in the off position, securely fasten a prominent warning device, such as a
tag, to the service panel.
Isolator
Ceiling
Plate
2-1. Drill two pilot holes into the wood support structure through the
outermost holes in the outlet box. e pilot holes should be 9/64”
in diameter.
Step 2-2
2-2. Your fan comes with four neoprene noise isolators (“Isolators”).
Position the isolators between the ceiling plate and ceiling by
inserting the raised areas on each isolator into the holes in the
ceiling plate.
2-3. read the lead wires from the outlet box down through the hole
in the middle of the ceiling plate.
2-4. Align the slotted holes in the ceiling plate with the pilot holes you
drilled in the wood support structure. For proper alignment use
slotted holes directly across from each other.
5
Note: e isolators should be flush against the ceiling.
2-5. Place a flat washer on each of the two 3” screws and pass the
screws through the slotted holes in the ceiling plate into the pilot
holes you drilled.
Steps 2-3 – 2-5
Tighten the screws into the 9/64” pilot holes; do not use lubricants
on the screws. Do not over tighten.
Flat Washer
3” Screw
For Angled Ceilings: Be sure to
orient the ceiling plate so that the
arrows printed on the ceiling plate are
pointing towards the ceiling peak.
41936-01 • 11/18/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
3 • Installing the Blade Irons
3-1. Turn the fan upside down. Use the ceiling fan package to support
the fan while assembling the blade irons.
3-2. Loosen all of the blade iron assembly screws. Do not completely
remove the screws.
3-3. Remove and discard all of the shipping blocks.
3-4. Slide the blade iron under the switch housing plate, aligning the
two notches with the two blade iron assembly screws.
3-5. To engage the blade iron fully, pull the blade forward under the
loosened blade iron assembly screws.
3-6. Securely tighten the blade iron assembly screws.
3-7. Repeat until all blade irons are assembled.
Blade Iron
6
Blade Iron
Assembly
Screws
Shipping Blocks
Two Notches
for Screws
Steps 3-1 – 3-7
Steps 3-4 – 3-7 Detail
Hunter Fan Company
41936-01 • 11/18/05
Download from Www.Somanuals.com. All Manuals Search And Download.
4 • Assembling and Hanging the Fan
Step 4-1
You can assemble your fan for standard mounting (steps 4-1 – 4-3) or
for low profile mounting (steps 4-4 – 4-6).
Pipe Ball Screw
4-1. If your ceiling is 9’ or higher, remove the 3” downrod pipe from
the black ball. Remove the screw and push the pipe up through
the ball. Remove the cross bar. read the cross bar through the
Ground Wire
and Screw
longer (6”) pipe and insert the pipe into the black ball. Tighten the
screw completely.
Pin
4-2. Insert the downrod through the canopy and canopy trim ring.
Feed the wires from the fan through the downrod on one side of
the pin in the ball.
Ball
4-3. Loosen the square head set screw on the adapter to install the
pipe and ball assembly. Note: When the pipe and ball assembly
is fully installed, 2-3 threads on the pipe will still be visible; this is
normal. Securely retighten the set screw with a wrench or pliers.
Skip to Step 4-7.
Wedge
Steps 4-2 – 4-3
Downrod
CAUTION: e adapter has a special coating on the threads. Do
not remove this coating; the coating prevents the downrod from
unscrewing. Once assembled, do not remove the downrod.
Canopy
7
4-4. Remove the set screw from the adapter.
Canopy
Note: For low profile mounting, the downrod is replaced with the
low profile washer. See Steps 4-4 – 4-6.
4-5. Place the low profile washer (lip up) into the canopy. Be sure the
green ground wire is pointing up toward the ceiling.
4-6. Align the holes in the washer with the holes in the adapter.
Assemble securely with three locking screws.
Trim Ring
Set Screw
Steps 4-5 – 4-6
Low Profile Washer
4-7. Raise the fan and place the hook on the ceiling plate through the
U-shaped hole in the rim.
WARNING: Fan may fall if not assembled as directed in these
installation instructions.
Step 4-7
U-shaped
Hole
Locking
Screw
41936-01 • 11/18/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
5 • Wiring the Fan
All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualified electrician.
Wall switches are not included. Select an acceptable general-use switch
in accordance with national and local electrical codes.
5-1. Disconnect the power by turning off the circuit breakers to the
outlet box and associated wall switch location.
5-2. Connect the wires as follows: connect the green ground wire to
the ground wire, connect white wire to white wire, connect the
black and the black/white wire from the fan to the black wire in
the ceiling.
5-3. To connect the wires, hold the bare metal leads together and place
a wire nut over them, then twist clockwise until tight.
Step 5-4
CAUTION: Be sure no bare wire or wire strands are visible after
making connections.
8
5-4. Push all wires and wire nuts back through the ceiling plate hole
into the outlet box.
Wire Nut
Hunter Fan Company
41936-01 • 11/18/05
Download from Www.Somanuals.com. All Manuals Search And Download.
6 • Installing the Canopy and Canopy Trim Ring
Step 6-2
Ceiling Plate
6-1. Holding the canopy, raise the fan off the hook.
6-2. Align the slots in the canopy with the tabs on the ceiling plate.
6-3. Raise the canopy over the ceiling plate. Rotate the canopy
clockwise until the tabs on the ceiling plate totally engage with
the slots in the canopy.
6-4. Loosely assemble the three canopy screws into the canopy one at
a time. Once all three screws are in, tighten them.
Canopy Trim
Ring
Canopy
6-5. Using both hands, push the canopy trim ring up to the top of the
canopy. e canopy trim ring will snap and lock into place.
Should you need to remove the canopy
trim ring, follow these steps:
1. Locate the tab indicators, small
bumps on top of tabs.
2. Press firmly on opposite sides of the
ring towards the canopy. e tabs
will flex out releasing the trim ring
from the canopy.
9
Step 6-3
Steps 6-4 – 6-5
Canopy
Screw
41936-01 • 11/18/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
7 • Assembling the Blades
Hunter fans use several styles of fan blade irons (brackets that hold the
blade to the fan).
7-1. Your fan may include blade grommets. If your fan has grommets,
insert them by hand into the holes on the blades.
Step 7-1 (Detail)
7-2. Attach each blade to a blade iron using three blade assembly
screws. If you used grommets, the blades may appear slightly loose
after screws are tightened. is is normal.
Blade Assembly
Screws
Use with grommet
Grommet
10
Steps 7-1 – 7-2
Use without grommet
Hunter Fan Company
41936-01 • 11/18/05
Download from Www.Somanuals.com. All Manuals Search And Download.
8 • Installing the Switch Housing
8-1. To attach the upper switch housing, partially install two housing
assembly screws into the switch housing mounting plate.
8-2. Feed the upper plug connector through the center opening of the
housing.
8-3. Align the keyhole slots in the housing with the housing assembly
screws.
8-4. Turn the housing counterclockwise until the housing assembly
screws are firmly situated in the narrow end of the keyhole slots.
Install the remaining housing assembly screw into the housing.
Tighten all three screws firmly.
CAUTION: Make sure the upper switch housing is securely attached
to the switch housing mounting plate. Failure to properly attach and
tighten all three assembly screws could result in the switch housing
fixture falling.
Steps 8-1 – 8-4
Housing
Assembly
Screw
Upper
Switch
Housing
8-5. To attach the lower switch housing, connect the upper plug
connector from the motor to the lower plug connector in the
lower switch housing assembly.
11
Note: Both plug connectors are polarized and will only fit together
one way. Make sure the connectors are properly aligned before
connecting them. Incorrect connection could cause improper
operation and damage to the product.
8-6. Place the lower switch housing assembly over the upper switch
housing. Align the side screw holes in the upper and lower switch
housings. Attach the lower switch housing to the upper switch
housing with three housing assembly screws.
Plug
Connector
Note: You can customize your Hunter fan with a number of accessory
light kits.
Steps 8-5 – 8-6
Lower
Switch
Housing
Housing
Assembly
Screw
41936-01 • 11/18/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
9 • Operating and Cleaning Your Ceiling Fan
9-1. Turn on electrical power to the fan.
9-2. e fan pull chain controls power to the fan. e pull chain has
four settings in sequence: High, Medium, Low and Off.
• Pull the chain slowly to change settings.
• Release slowly to prevent the chain from recoiling into the
blades.
• e chain uses a breakaway connector that separates if the
chain is jerked. If this happens, simply reinsert the chain into
the connector.
9-3. Ceiling fans work best by blowing air downward (counterclockwise
blade rotation) in warm weather to cool the room with a direct
breeze. In cold weather, having the fan draw air upward (clockwise
blade rotation) will distribute the warmer air trapped at the
ceiling around the room without causing a draft.
In warm weather, use
downward air flow pattern
9-4. For cleaning finishes, use a soft brush or lint-free cloth to prevent
scratching. A vacuum cleaner brush nozzle can remove heavier
dust. Remove surface smudges or accumulated dirt and dust using
a mild detergent and a slightly dampened cloth. You may use
an artistic agent, but never abrasive cleaning agents as they will
damage the finish.
12
9-5. Clean wood finish blades with a furniture polishing cloth.
Occasionally, apply a light coat of furniture polish for added
protection and beauty. Clean painted and high-gloss blades in the
same manner as the fan finish.
In cold weather, use upward
air flow pattern
To Change Airflow Direction
Turn the fan off and let it come to a complete
stop. Slide the reversing switch on the fan to the
opposite position. Restart fan.
Reversing
Switch
Hunter Fan Company
41936-01 • 11/18/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Hunter fans have the power to cut your cooling costs up to 40%.
Beat the High Cost of Cooling
e air movement created by a Hunter ceiling fan lets you set your
thermostat higher and still stay comfortable. Every degree you
raise the thermostat saves up to 7% on energy costs. So, you can
cut back on expensive air conditioning...and save up to 40%* on
cooling. In winter, your Hunter fan recirculates warm air and saves
up to 10%* on heating bills.
* On average at low speed settings. Your savings may vary based
on climate, building type and thermostat setting.
Save Energy and Money While Protecting the Environment
Congratulations! You’re saving energy and money while protecting
the environment by purchasing this ENERGY STAR qualified
Hunter ceiling fan! With this purchase, you are doing your part to
protect the environment. In 2010, ENERGY STAR qualified ceiling
fans are projected to cut air pollution by more than 500 million
pounds!
13
Your new ceiling fan has earned the ENERGY STAR label
because it meets high energy efficiency specifications set by
the Environmental Protection Agency (EPA). ENERGY STAR
labeled ceiling fans save energy because they have more efficient
fan motors and air delivery due to more aerodynamic blade
configurations. Ceiling fan models bearing the ENERGY STAR label
move air 14 - 20% more efficiently than typical ceiling fan models.
41936-01 • 11/18/05
Hunter Fan Company
Download from Www.Somanuals.com. All Manuals Search And Download.
10 • Troubleshooting
Problem: Nothing happens; fan does not move.
1. Turn power on, replace fuse, or reset breaker.
2. Loosen canopy, check all connections according to the wiring the
fan section.
3. Check the plug connection in the switch housing.
4. Push motor reversing switch firmly left or right to ensure that the
switch is engaged.
5. Pull the pull chain to ensure it is on.
6. Remove the shipping bumpers.
Problem: Noisy operation.
1. Tighten the blade bracket screws until snug.
2. Check to see if the blade is cracked. If so, replace all the blades.
Problem: Excessive wobbling.
1. If your fan wobbles when operating, use the enclosed balancing kit
and instructions to balance the fan.
2. Tighten all blade iron screws.
14
3. Turn power off, support fan very carefully, and check that the
hanger ball is properly seated.
If you need parts or service assistance, please call
888-830-1326 or visit us at our Web site at
Hunter Fan Company
2500 Frisco Avenue
Memphis, Tennessee 38114
Hunter Fan Company
41936-01 • 11/18/05
Download from Www.Somanuals.com. All Manuals Search And Download.
|