Digital Set-Top Box with Nagravision Embedded
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safeguards
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may cause undesired operation.
This television receiver provides display of television closed captioning
in accordance with §15.119 of the FCC rules.
CAUTION - TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
WARNING - TO REDUCE RISK OF FIRE OF SHOCK HAZARD,
DO NOT EXPOSE THIS RECEIVER TO RAIN OR MOISTURE.
GB2
Download from Www.Somanuals.com. All Manuals Search And Download.
Always be careful when using your product. To reduce the risk of fire electrical shock and
other injuries, keep these safety precautions in mind when installing, using and maintaining
your machine.
• Read all safety and operating instructions before operating your product.
• Keep the safety and operating instructions for future reference.
• Heed all warnings on the product receiver and in the operating instructions.
• Follow all operating and use instructions.
• Unplug the product from the wall outlet before cleaning.
Use a damp cloth. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
• Never add any attachments and/or equipment without approval
of the manufacturer. Such additions can increase the risk of fire,
electric shock or other personal injury.
• Do not use the product where contact with or immersion in water
is a possibility, such as near bathtubs, sinks, washing machines,
swimming pools etc.
• Do not place the product on an unstable cart, stand, tripod, bracket or table where it can fall.
A falling product can cause serious injury to a child or adult and serious damage to the appliance.
Use only with a cart, stand, tripod, bracket or table recommended by the manufacturer or sold
with the product. Follow the manufacturer’s instructions when mounting the unit and use a mounting
accessory recommended by the manufacturer. Move the product and cart with care.
Quick stops, excessive force and uneven surfaces can make the unit and cart unsteady and likely
to overturn.
• Provide ventilation for the product. The unit is designed with slots in the cabinet for ventilation to
protect it from overheating. Do not block these openings with any object and do not place the
product on a bed, sofa, rug or other similar surface. Do not place it near a radiator or heat register.
If you place the product on a rack or bookcase, ensure that there is adequate ventilation and that
you’ve followed the manufacturer’s instructions for mounting.
GB3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safeguards
• Operate your product only from the type of power source indicated on the marking label.
If you are not sure of the type of power supplied to your home, consult your appliance
dealer or local power company.
• Use only a grounded or polarized outlet. For your safety, this product is equipped with a
polarized alternating current line plug having one blade wider than the other. This plug will
fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet,
try reversing the plug. If the plug still does not fit, contact your electrician to replace your outlet.
• Protect the power cord. Power supply cords should be routed so that they won’t be walked on
or pinched by objects placed on or against them. Pay particular attention to cords at plugs,
convenience receptacles and the point where they exit from the unit.
• Unplug the product from the wall outlet and disconnect the antenna or cable system during
a lightning storm or when left unattended and unused for long periods of time.
This will prevent damage to the unit due to lightening and power-line surges.
• Avoid overhead power lines. An outside antenna system should not be placed in the vicinity
of overhead power lines or other electric light or power circuits or where it can fall into such
power lines or circuits. When installing an outside antenna system, be extremely careful to
keep from touching the power lines or circuits. Contact with such lines can be fatal.
• Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.
• Do not insert anything through the openings in the unit, where they can touch dangerous
voltage points or damage parts. Never spill liquid of any kind on the product.
• Ground outdoor antennas. If an outside antenna
EXAMPLE OF
is connected to the product, be sure the antenna
is grounded so as to provide some protection
ANTENNA GROUNDING
ANTENNA
LEAD IN WIRE
against voltage surges and built-up static charges.
Section 810 of the National Electrical Code,
ANSI/NFPA No.70-1984, provides information
about proper grounding of the mast and supporting
structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes and
GROUND CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
requirements for the grounding electrode.
NEC NATIONAL ELECTRICAL CODE
(NEC ART 250, PART H)
GB4
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not attempt to service the product yourself. Refer all servicing to qualified service personnel.
Unplug the unit from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
- when the power-supply cord or plug is damaged
- if liquid has been spilled on the unit or if objects have fallen into the unit
- if the product has been exposed to rain or water
- if the product does not operate normally by following the operating instructions
- if the product has been dropped or the cabinet has been damaged
- when the product exhibits a distinct change in performance
• If you make adjustments yourself, adjust only those controls that are covered by the operating
instructions. Adjusting other controls may result in damage and will often require extensive
work by a qualified technician to restore the product to normal.
• When replacement parts are required, be sure the service technician uses replacement parts
specified by the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in additional damage to the unit.
• Upon completetion of any service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in a safe operating condition.
• CATV system installation : this reminder is provided to call the CATV system installer’s attention
to article 820-40 of the nec that provides guidelines for proper grounding and in particular,
specifies that the cable ground shall be connected to the grounding system of the building,
as close to the point of cable entry as practical.
GB5
Download from Www.Somanuals.com. All Manuals Search And Download.
Support & Copyright
First and foremost, our knowledge of the set top box marketplace along with technical expertise
differentiates HUMAX. Moreover, we maintain very close working relationships with our
customers. We take a highly disciplined engineering approach to product design, manufacture,
testing, acceptance and to technical and maintenance support. We conduct comprehensive
testing of the units, provide complete documentation and support and deliver the highest quality,
most consistent products on time and every time.
HUMAX supports you via its homepage with useful information and new software of the
HUMAX’s homepage.
To provide you the convenience of usage HUMAX has the right to make changes and
improvements to any of the products described in this manual and the manual of the
products without notice.
Copyright © 2000. HUMAX Co., Ltd.
All rights reserved.
Warning
HUMAX cannot be held responsible for any kind of problems caused by the use of unofficial
softeware. The use of software versions other than HUMAX official software will void the
manufacturer’s warranty.
It is advised that only the formal software released from HUMAX should be used in all
HUMAX product range.
Caution
To watch Pay Per View programmes, be sure to inform your STB dealer of the STB’s and
Smart card’s serial numbers. So that they can pair your STB with your Smartcard.
Otherwise, you cannot watch the programmes because they are scrambled.
GB6
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
1. Connect DiSEqC 1.0
All our receivers are designed to be DiSEqC 1.0 compatible. This allows multiple antennas to be
connected to the STB simultaneously.
If you have two or more fixed antennas or LNBs, you can use a DiSEqC 1.0 switch.
1. Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the
DiSEqC switch.
2. Connect the coaxial cable from the second LNB to the LNB 2 or LNB B input connector of the
DiSEqC switch.
3. Do the same for other LNBs.
4. Connect one end of a Coaxial cable to the RF output connector of the DiSEqC switch and the
other end to the LNB IN socket on the STB.
2. Connect DiSEqC 1.2
Please refer to page GB37.
The Locking Time might take longer than expected during the initial boot if the motorised system
is set “enable” mode.
3. Connect a Satellite antenna
To the digital receiver, you can connect either a single satellite antenna directly or through
converter box several antennas or LNB of multi-feed equipment.
You can connect a further Sat-receiver (for example analog), with the receiver of common
antenna equipment that has satellite signals.
GB7
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
4. Software Upgrade
HUMAX digital set-top box is a highly sophisticated product-incorporating one of the best
software applications.
Whenever a problem is found with this software or, in fact, extra functions or enhanced
applications are added, the software in the equipment has to be upgraded.
In order to maintain proper performance of the product, it is essential to have the most
up to date software. The latest news and release of software versions may be found at
It is recommended that users register to HCSA (HUMAX Customer Service Area) and
periodically check for the availability of software upgrade.
There are three methods to upgrade the software :
(a) set-top box to set-top box download (copies the software of the main unit into slave unit);
(b) pc to set-top box download (downloads the software directly from pc to the model
requiring upgrade);
(c) OTA over-the-air (downloads the software where the manufacturer reserves the right to
decide when and where to release through satellite system).
Over The Air (OTA) is simply another alternative for downloading software versions.
However, the manufacturer reserves the right to decide when and where this software upgrade
can take place by "beaming" latest software versions over the air via satellite
systems. Note that OTA is only limited to certain geographical regions mainly due to
different satellites having different footprints (area where the signal can be received).
SUSS (TM) is an official trademark and logo for HUMAX loader software to perform OTA.
The software upgrade via satellite system will only occur under the following circumstances :
1) the equipment should have appropriate loader software;
2) the manufacturer decides to release software downloading via a designated satellite
system;
3) the equipment must be "tuned" properly to the same satellite that the manufacturer uses.
GB8
Download from Www.Somanuals.com. All Manuals Search And Download.
STB Connections
Front Panel Control and LEDs
1
,
Press to change services down and up.
2
3
4
5
6
7
SMART CARD SLOT
Insert the SMART CARD with it’s IC-Chip part facing the bottom side.
ERROR LED (AMBER)
Indicates that the STB has an error.
STANDBY LED (RED)
Indicates that the STB is under Standby.
OPERATING LED (GREEN)
Indicates that the STB is operating.
TV/RADIO
Press to switch between TV and Radio modes.
STANDBY
Press to switch between Operation and Standby modes.
GB9
Download from Www.Somanuals.com. All Manuals Search And Download.
STB Connections
Rear Panel Connectors
1
2
3
LNB IN
Use to connect an antenna.
RS-232C
Use it when connecting to your PC.
RCA AUDIO OUTPUT
Use to connect an audio signal from your STB to an audio input jack
on a VCR or TV.
4
5
6
RCA VIDEO OUTPUT
Use to connect video signal from your STB to a video input jack
on a VCR or TV.
RF OUT
Use to connect a RF signal from your STB to RF(ANT) input jack
on your TV.
RF IN
Use to connect a general AIR ANT and CABLE jacks to a RF in jack
on the STB.
GB10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Set-Top Box to Your TV (using a RF CABLE)
From Cable/ Antenna Source
TV Rear Panel
1. Connect a parabola antenna cable to the LNB IN jack.
Connect an AIR or Cable Box Antenna out terminal to the RF IN jack.
2. Connect between the RF OUT jack on the STB and the ANT INPUT
(RF INPUT) jack on the TV.
Viewing the STB programs
3. Turn on your STB and TV.
4. Tune the STB to VHF Channel 3 or Channel 4.
5. Tune the TV to Channel 3 or Channel 4 (same as you tune the STB).
6. Operate the STB to select a program you want to watch.
Viewing the Free-To-Air or CABLE programs
7. Switch to the STB Standby Mode.
8. Select a channel you want to watch using the TV remote control.
GB11
Download from Www.Somanuals.com. All Manuals Search And Download.
STB Connections
Connecting the Set-Top Box to Your TV (using a RCA CABLE)
From Cable/ Antenna Source
TV Rear Panel
1. Connect a parabola antenna cable to the LNB IN jack.
Connect an AIR or Cable Box Antenna out terminal to the RF IN jack.
2. Connect between the RF OUT jack on the STB and the ANT INPUT
(RF INPUT) jack on the TV.
3. Connect a set of audio, video cables between the AUDIO, VIDEO OUT jacks on the STB
and the AUDIO, VIDEO INPUT jacks on the TV.
Viewing the STB programs
4. Turn on your STB and TV.
5. Switch to the Video mode using the TV remote control.
6. Operate the STB to watch a program you want.
An S-Video Cable produces better picture quality than a Video Cable.
Viewing the Free-to-Air or CABLE programs
7. Switch to the STB Standby mode.
8. Switch to the TV Air mode using the TV remote control and then select a TV channel
you want to watch.
Using a HI-Fi SYSTEM for sound
9. Connect a set of audio cables between the AUDIO OUT jacks on the STB
and the AUDIO (LINE, AUX) INPUT jacks on the HI-Fi SYSTEM.
GB12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Set-Top Box to Your TV and VCR
You can view a STB program and record it using a VCR at the same time.
From Cable/ Antenna Source
TV Rear Panel
VCR Rear Panel
1. Connect a parabola antenna cable to the LNB IN jack.
Connect an AIR or Cable Box Antenna out terminal cable to the RF IN jack.
2. Connect between the RF OUT jack on the STB and the ANT INPUT
(RF INPUT) jack on the TV.
3. Connect a set of audio, video cables between the AUDIO, VIDEO OUT jacks on
the STB and the AUDIO, VIDEO INPUT jacks on the VCR.
Recording a program from STB
• Turn on the VCR to record a program from the STB.
• When you record a STB program of a specific time, set the Wakeup Time and Service No.
of the STB Time Setting Mode to meet the starting time of the program and then do ON
• Time and Recording Time of the VCR Time Setting Mode.
(See your VCR manual for VCR ON Time and setting the Recording Time.)
Viewing a program from the STB, Free-To-Air or CABLE
• See “Connecting the Set-Top Box to your TV (using a RF CABLE).”
GB13
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Unit
STANDBY
NUMBER BUTTONS
INFORMATION (RED)
TV/SAT (Reserved)
TV/RADIO
MUTE
SOUNDTRACK (GREEN)
SUBTITLE (YELLOW)
MENU
PAUSE (BLUE)
TIME (WHITE)
EXIT
CURSOR
OK
P+/P-
HELP
EPG
V+/V-
RCL (Recall)
RS-101N
GB14
Download from Www.Somanuals.com. All Manuals Search And Download.
10
11
1
2
NUMBER BUTTONS
Press to select a service, enter your
PIN Code or Numbers on the menu.
TV/SAT (Reserved)
TV/RADIO
Press to switch between TV and Radio modes.
INFORMATION (RED)
12
13
Press to display the program information box
on the screen. This button functions same
as the RED button on the menus.
MUTE
Press to temporarily cut off the sound.
MENU
3
SOUNDTRACK (GREEN)
Press to display the Main Menu on the screen
Press to display the soundtrack list for the
current service. And this button functions
same as the GREEN button on the menus.
or return to the screen from a sub menu screen.
14
CURSOR
Press to move the highlight bar for selecting
4
5
SUBTITLE (YELLOW)
options on the menus.
Press to display the subtitle language list for
And this button is used to change services
(up/down) and increase or decrease the audio
volume.
the current service. And this button functions
same as the YELLOW button on the menus.
PAUSE (BLUE)
15
16
OK
Press to pause the moving picture for seeing
more careful. And this button functions same
as the BLUE button on the menus.
Press to display the service list.
This button is used to select the item on
the menus.
6
TIME (WHITE)
P+/P-
Press to display the current time on the screen.
Press to reserve services on the Information
box or EPG. And this button functions same as
the WHITE button on the menus.
Program up/down buttons.
Press to tune to the next or previous service.
Press to move up or down pages on the menus.
17
18
HELP
7
8
9
EXIT
Press to display the help box on the screen.
Press to return to the previous menu
and screen.
EPG
Electronic Program Guide button displays
the TV/Radio Program guide.
V+/V-
Volume up/down buttons.
Press to increase or decrease the volume.
19
RCL (Recall)
Press to select the channel that was previously
viewed.
STANDBY
Press to switch between Operation and
Standby modes.
• Please note : The design of Remote Control Unit may be changed without notice in advance.
GB15
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Guide
Information Box (I-Plate)
The details of Service Part and Event Part are automatically
displayed on the I-Plate when pressing the(
)button or changing
services. I-Plate is divided into Service Part and Event Part.
SERVICE-PART (Left side of the box)
Service Part consists of the following item :
• I-Plate icon, Current Time
• Service Name, Service Number, icon
• Subtitle, Teletext, Scrambling Service Symbol
(These are automatically displayed when the broadcasting
station provides appropriate information.)
• Signal Quality Bar
EVENT-PART (Right side of the box)
EVENT PART consists of the following items:
• Event name, Event duration time
• Description of event, State of reserved event
Event Part shows the current and next event information.
button : Use to move from the current event information to the
next event information.
button : Use to move from the next event information to the
current event information.
When the Help(
)button is pressed under I-Plate display,
the help window will appear on the screen.
The Help window shows the extended current event information,
including: Satellite Name, Frequency, Polarization, Symbol Rate, FEC...
The detailed information for the event can be displayed by pressing the
Help(
You can reserve the program in the event data display mode by using
the Time( )button.
)button in the I-Plate with event data displaying mode.
When the current data is displaying on the screen, you can reset timer
program Once, Daily or Weekly mode.
When you release the timer program mode, then you will be asked to
confirm the action.
Volume Control
To adjust the volume level, use the
To temporarily stop the volume, press the Mute(
To cancel Mute, press the Mute( )button again or press the
buttons or buttons.
buttons or
buttons.
)button.
GB16
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Services
To change services, do in the following sequence:
1. Press the Number buttons(0~9) on the remote control.
2. Press the
Or press the Recall(
To switch between TV and Radio services, press the TV/Radio
)button.
buttons or
buttons.
), Service-List(
), EPG(
)button.
(
To select the previous viewed service, press the Recall(
)button.
Soundtrack
When you want to watch the Audio Language of soundtrack under
servicing, press the Soundtrack( )button firstly.
The on-screen menu is displayed on the top to left side of the screen.
To change the audio language:
1.
2.
3.
buttons
: Use to select the Audio on the left, right or both.
buttons : Use to select the audio language you want.
button : When this button is pressed, the menu
,
screen will disappear keeping the selected audio soundtrack
constant.
When the current service is switched, the audio language returns to
the audio language that was selected in previoius service. If the
returned audio language is invalid, the audio language that you
selected from the audio language menu has the priority of playback.
Subtitle
When the current broadcasting programme provides subtitle, press
the Subtitle(
)button to see the current subtitle language list.
To change the subtitle language:
Use the
Press the
buttons to select a Subtitle language you want.
button and the selected language is highlighted and
then the Subtitle language you want is displayed on the screen.
Press the
button to cancel the Subtitle mode.
Teletext
Use your TV remote control unit to control the Teletext service.
The teletext button doesn’t exist on the STB remote control unit.
When the service supports Teletext, the Teletext icon( ) is displayed
on the i-plate.
GB17
Download from Www.Somanuals.com. All Manuals Search And Download.
Function Guide
Service List
To select the desired service in the service list, you should firstly
display the service list using
select a service and press
button. Use
button. Also use
buttons to
buttons to
select a service directly in the service list.
The Service List consists of Service All and Service Favorite.
On the Service List, you can change the attributes of a service
through the Service Configuration.
button : Use to move to the previous or next service
button : Use to move to the forward or backward
service (maximum 6 services).
Red button
(
) : Service All
Green button(
) : Service Favorite
Service Configuration
To change the attributes of a service.
1. Use the
in the Service All or Service Favorite mode.
2. Press the Menu( )button.
3. Use the buttons to move to an item (such as favorite,
lock, skip, delete) you want on the Service Configuration screen.
buttons to move a service you want to change
4. Use the
buttons to select. Press the
button to complete.
Service All
1. To display the service list, press the
Use Red( )button to select the Service All List.
2. Select the desired service by using the buttons.
3. Press the button to view the selected service.
button.
The right side scroll-bar of the screen displays the location
of the selected service in relation to All Services.
Service Favorite
1. To add the services to the Service Favorite, use the Service
Configuration at Service All or Service Organizing menu.
2. When you press the Green(
)button in the Service List,
the favorite service list will be displayed on the screen.
3. When you want to see the services added to the favorite group,
use the
button.
GB18
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu Guide
1. TV Guide
Your STB has an Electronic Program Guide(EPG) to help you
navigate through all the possible viewing options.
The TV Guide supplies information such as program listings and
start and end times for all available services.
In addition, detailed information about the program listings and
start and end times for all available services.
In addition, detailed information about the program is often
available in the EPG(the availability and amount of these
program details will vary, depending on the particular broadcaster).
2. Parental Control
Access to services and programs is controlled by a PIN Code
(i.e., a 4-digit secret code that is defined by the user).
The very first time you attempt to lock all services(or lock
programs by ratings), the on-screen menu will instruct you to assign
a PIN Code (Later on, if necessary, you can change it).
3. Installation
The Installation mode allows you to have the information of setting
services and newly set services (language, time, organize, search,..)
Furthermore, you can recognize the states of hardware and
software versions and signals from your STB.
4. Utility
This menu provides Calendar and Biorhythm.
GB19
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu Guide
1. TV Guide
You can watch a program being shown and reserve it in the
TV Guide mode.
To enter the TV Guide mode
Press the EPG(
)button on the remote control unit or select the
TV Guide on the Main Menu.
To select the TV/Radio Guide
Press the
button on the remote control unit and TV Guide will
be switched to the Radio Guide.
TV Guide mode includes four different modes.
To select each mode, use the following buttons:
• Red
• Green(
• Yellow(
(
)button : Use to display the current or next program list.
)button : Use to display the program list for one-week.
)button : Use to display the reserved program list.
• Blue
(
)button : Use to display the simple TV Guide list.(Quick mode)
NOW / NEXT mode
Show the informations of the program that are played now or
will be played next time.
This mode consists of the service name, event name, event
duration time, current time and on-screen-display window.
To watch a program you want through the display window :
• Use the
The selected service will appear on the right display window.
• Use the buttons to select a program you want.
And then press the button on the remote control unit.
buttons to select a program you want.
The selected service will appear on the right display window.
The selected OSD will be highlighted every time the cursor moves.
To reserve a program you want :
• Select a program you want by using the
buttons. And then press the White(
buttons or
)button.
Press the
buttons to watch the program of previous
page or the program of next page.
Press the Yellow(
)button to watch the reserved program list.
GB20
Download from Www.Somanuals.com. All Manuals Search And Download.
Weekly mode
Shows the information of programs that will be played for a week.
Select a day you want using the
buttons.
To watch and reserve a program you want, do the same steps with
the NOW/NEXT mode.
Reserved mode
Shows the program lists that you have already reserved on the
TV Guide or Information Box. Maximum twenty programs can be
reserved. This program list includes service name, date, duration
time, reservation mode and event name.
To cancel the Reserved service, select a program you want to
cancel using the
buttons and then press the White(
)button.
Quick mode
Shows a simple TV Guide like an Information box.
This mode shows in the A/V playback mode.
• Blue vertical line : Indicates the current time.
• Black/white bar : Shows the proceeding state of program.
• Time range of bar : This consists of three blocks by 30 minutes
per block.
GB21
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu Guide
2. Parental Control
You can set a parental guidance rating to each program in this
mode.
1. When the
button is pressed after selecting the highlighted
parental control on the initial menu screen, a display window
for entering the PIN Code will appear on the center of screen.
0 0 0 0
** The default PIN Code is
.
2. Enter the PIN Code on the display window.
(If any problem occurs when entering a PIN Code, you cannot
switch to the next mode.)
3. Set the parental guidance rating of highlighted censorship
classification.
Classification: no block or total block.
Enter the PIN Code to unlock or lock programs.
4. To change your PIN Code:
Select the highlighted Old Pin Code using the
and then enter your Old PIN Code.
buttons
Enter a New PIN Code in the highlighted new PIN Code
using the buttons.
To verify the New PIN Code, re-enter a new PIN Code in the
highlighted Verify Changed PIN Code.
5. When the entered PIN Code is correct, then all settings are
completed. (If the PIN Code is wrong, the message “PIN Code
mismatch” will be displayed on the display window. When the
button is pressed at this time, the old PIN Code is valid and the
cursor is located in the first position of this menu.)
3. Installation
This mode allows you to customize, add a new service and displays
the state of the STB. Enter the submenus after selecting the
Installation Mode in the Main Menu.
3-1. System Setting
The System Setting mode supports the STB internal settings
according to the connection of the receiver and external units.
This mode includes Language Setting, Time Setting,
A/V Output Setting, VHF Tuning and Other Setting.
GB22
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Setting
Select the language for Menu, Audio or Subtitle.
1. Select the highlighted Language Setting using the
in the System Setting mode and then press the
buttons
button.
2. Select the highlighted Menu(or Audio, Subtitle) Language and
press the
3. Use the
press the
buttons and the language list will be displayed.
buttons to move to a language you want and then
button to finish setting.
Menu Language
Select a language for the menu or banner OSD in this mode.
You can choose the language from a selection of Arabic, English,
French, Italian, Persian, Portuguese, Spanish and more.
When a broadcasting information(event) is transmitted, the selected
Menu Language will be applied.
• The kind of languages can be changed depending on the country.
Languages are subject to change without prior notice.
Audio Language
Select the Default Language for audio when changing services.
If you change the current service, your STB will initially select
the previously memorized Audio Language. If the Audio Language
of current service is not provided, at this time, you should reselect
a language on the Audio Language menu.
Languages provided:
Czech, Danish, Dutch, Norwegian, English, Finnish, French,
German, Greek, Hungarian, Italian, Portuguese, Rumanian,
Russian, Spanish, Swedish, Turkish and more.
If no language is provided, then the default language of current
service will be automatically selected.
Subtitle Language
Select the Default Language for Subtitle when changing services.
Language provided: Danish, English, Finnish, French, German,
Greek, Hungarian, Italian, Norwegian, Portuguese, Spanish,
Swedish and more.
GB23
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu Guide
Time Setting
You can set the Current Time and Wakeup Time in this mode.
Furthermore, the Service Number in the Wakeup Time mode and
Sleep Time (standby mode) can be set. When a VCR is connected,
recording can be automatically done according to Wakeup/Sleep
Time Setting.
Current Time
To set the Current Time, enter the Offset value using the
standardized information of current service area.
The time setting will be used as the standardized time for the
I-Plate, TV Guide, Wakeup and Sleep timer.
Time Offset
Current time is based on TDT (Time and Data Table) at the stream
of the current service.
Wakeup Time
Select the time when STB is turned on.
Use the Number buttons(0~9) on the remote control unit to enter
your Wakeup Time.
Wakeup Service No.
Use the
buttons to set the service number provided for the set
Wakeup Time.
Use the TV/Radio(
TV/Radio service.
)button on the remote control unit to toggle
Service Name
The Service Name that has been determined by the
Wakeup Service No. will be shown.
Sleep Time
Depending on Time Setting, select the time when STB is turned off.
GB24
Download from Www.Somanuals.com. All Manuals Search And Download.
A/V Output Setting
Audio Output
Set the Audio mode which is output from RCA/Cinch Jack.
(STEREO/MONO)
Screen Mode
Select the aspect ratio of TV which is connected to STB(4:3 or 16:9).
Display Format
Select the format which the video is to be displayed on screen.
When your TV set is 4:3 and video source is 16:9,
STB will display in Letter-box or Center mode as selected.
When your TV set is 16:9 and video source is 4:3,
STB will display in the Pillar-box or Full mode as selected.
NTSC Mode
Adjust this value between 3.58 and 4.43 if your TV displays the video
only in black and white color. Normally NTSC 3.58 mode is used
worldwide, but some TV sets can support only NTSC 4.43 mode.
VHF Tuning
When you watch TV after connecting a cable between
the RF OUT jack on STB and the Input jack (RF Input) on TV.
If you select Channel 3 or Channel 4 and then set VHF Tuning to
Channel 3 or Channel 4, all services from STB will be viewed
through TV Channel 3 or Channel 4.
GB25
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu Guide
Other Setting
Select the OSD transparency and Information Box Display Time.
OSD Transparency
Select the OSD transparent type. It affects Information Box, Service
List, Time and Quick mode of TV Guide. Use the
toggle transparent and opaque.
buttons to
Info. Box Display Time
Set the display duration of Information Box displayed on the screen
after changing services. The time ranges from 0 to 20 seconds.
Menu Mode
Select NTSC, PAL, AUTO according to your TV type.
In AUTO mode, the menu is automatically selected as NTSC or PAL
according to the service played before the Menu mode is entered.
3-2. Service Organizing
This menu gives users access to options that allow them to organize
their Networks, TV services and Radio services.
0 0 0 0
** The default PIN Code is
.
Organize TV Services
Organize services that are included in memory for TV.
Organize All Services
Delete, Move, Lock, Skip or Rename each TV service on all
TV service list.
• Delete
1. Use the
buttons to select a service you want to delete.
2. When the Red(
)button is pressed, the service will be colored
in gray.
3. When the
button is pressed, the message “Saving changed
Service Information” will appear on the center of screen and
simultaneously the service will be deleted.
If you don’t want to delete, then press the
If the message “Do you want to save?” appear on the center of
screen, press the button.
button.
GB26
Download from Www.Somanuals.com. All Manuals Search And Download.
• Move
1. Use the
buttons to select a service you want to move.
)button is pressed, the icon( ) will appear
in front of the service number.
3. Use the buttons to move to the location you want
2. When the Green(
to use.
4. When the
button is pressed, the message “Saving
changed Service Information” will appear on the center of screen
and simultaneously the location of service will be changed.
If you don’t want to move, press the
button.
• Lock
1. Use the
buttons to select a service to be locked by your
PIN Code.
2. Press the Yellow(
displayed at the right side of the service name.
)button and the symbol ( ) will be
3. Press the
button and the message “Saving changed Service
Information” will appear on the center of screen and
simultaneously the selected service will be locked.
If you don’t want to lock, then press the
remote control.
button on the
If the message “Do you want to save?” appears on the center of
screen, then select
.
To watch the locked service, be sure to enter your registered
PIN Code.
• Skip
1. Use the
2. Press the Blue(
at the right side of the service name.
3. Press the button, and the message “Saving changed Service
buttons to select a service you want to skip.
)button and the symbol( ) will appear
Information” will appear and simultaneously the selected service
will be skipped.
If you don’t want to skip, then press the
button.
If the message “Do you want to save?” appears on the center of
screen, select
When the
.
buttons or
buttons are used to select
channels, the skipped service channels will not be shown.
To watch the skipped service channels, use the
Number buttons(0~9), Service List or the EPG mode.
GB27
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu Guide
• Rename
1. Use the
buttons to select a service you want to rename.
2. Press the White(
)button and the keyboard image will appear
on the center of screen.
3. Use the
press the
buttons to select a new name and then
button.
4. Press the Yellow(
)button to finish renaming.
Organize Favorite Services
Delete, Move, Lock, Skip or Rename each TV service in a
favorite TV group and re-group them into your favorite TV group.
This mode has the same operating methods as
“organize all services”.
Moving the favorite group from the service group:
1. Press the
2. Use the
move.
button to move to “Services”-Plate (right window).
buttons to select a service channel you want to
3. Press the
button and the selected service channel will be
moved to “Favorites”-Plate (left window).
4. To finish this menu:
• Press the
• Press the
button to move to “Favorites”-Plate (left window).
button and the message “Saving changed
Service Information” will appear on the center of screen.
Press the button and the message “Do you want to save?”
will appear on the center of screen.
At this time, press the button.
note :
1.
2.
buttons : Use to move services and favorite window.
buttons : Use to move to the previous page and the
next page.
GB28
Download from Www.Somanuals.com. All Manuals Search And Download.
Organize Radio Services
Same functions as “Organize TV Services”
Organize Networks
You can edit services using the network unit.
The network names are displayed on the left side of screen,
and the TV/Radio Services included in the highlighted network are
displayed on the right side of screen.
Only the Delete, Move, Rename Function can be used in this mode.
Delete Satellites
The Delete Satellites menu supplies the following functions,
• Delete a satellite. It will also delete all services belonging to the
satellite
• Delete a transponder. it will also delete all services belonging to
the transponder.
• Sort the services according to the satellite and the transponder.
3-3. Service Searching
Search for new services.
This mode includes Antenna Setting and Manual Search.
Antenna Setting
Select LNB parameters and switching connections.
Antenna Alternative
Use the
buttons to select an antenna number for the required
satellite. Antenna alternative 16 is fixed for SMATV and its name
can’t be changed.
GB29
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu Guide
Satellite Name
Selects the satellite name that corresponds to the value of the
Antenna Alternative.
Press the
buttons and the satellite names you can memorize
will be listed on the screen.
Use the
the
buttons to select a satellite name and then press
button.
This name will help you Select Antenna Alternative In Manual Search
menu.
note : Press User defined and the keyboard image will appear
on the screen. Then you can enter satellite names.
LNB Frequency
Use the
buttons to select a LNB frequency or type on the dish.
You can select the LNB Frequency.
If the required LNB frequency is not available, then press the
Number buttons(0~9) on the remote control.
22KHz Tone
Use the
buttons to select the antenna tone switch when LNB
Frequency is universal.
22KHz tone will be switched automatically.
DiSEqC Input
Use the
buttons to select a DiSEqC antenna switch type.
(according to the option and location of DiSEqC switch)
• Type : Disabled, Tone Burst A to B, DiSEqC A, DiSEqC B,
DiSEqC C, DiSEqC D.
Motorized System
It disables/enables the motorise function.
Set this according to the used antenna.
If you wish to use this system, please refer to page GB37.
LNB Voltage
It sets the level of LNB voltage. The LNB voltage may be dropped
too low to supply power to LNB owing to long length of the signal
line. To compensate the voltage drop, the item shall be set as “High”.
GB30
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual Search
Find the services manually in the transponder you select.
This search mode included normal advanced and SMATV search.
Antenna Alternative
Use the
buttons to select an antenna number for the required
satellite. The satellite name will help you select antennas.
If you want to search in SMATV mode, then select the Antenna
Alternative 16.
Frequency
Use the
buttons to enter the Frequency of the transponder
you want to find (MHz). Or use the Number buttons(0~9) on the
remote control.
Polarization
Use the
Horizontal : 18 V are output through LNB line
Vertical : 13.5 V are output through LNB line
buttons to select the Polarization of the transponder.
Symbol Rate
Inputs the Symbol Rate of the transponder you want to find.
FEC (Forward Error Correction)
Use the
buttons to select the Forward Error Correction of
the transponder.
You can select the value of auto, 1/2, 2/3, 3/4, 5/6 and 7/8.
Network Search
Select “Yes” and you can find more services using the home
network.
Automatic Skip
If you want to find free services, then select “Yes”.
The scrambled services will not be automatically stored.
GB31
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu Guide
Advanced
Press the
button to find services using PIDs and more items for
button and Video,
selecting PIDs will be displayed. Press the
Audio and PCR PID items will be added. Enter the PID values for
Video, Audio and PCR. When the Number buttons(0~9) are
pressed,
a hexadecimal table will be displayed. Then you can’t enter the PID
values using the keyboard.
Automatic Search
When you enter the Satellite Name that is set in Antenna Setting
menu, search all of the selected satellite without inputting the extra
frequency.
Antenna Alternative
Select the target antenna for Automatic Service Search.
The attribute of this antenna alternative number is already set in
Antenna Setting menu and the Satellite Name is helpful in the
selection of the antenna, but in this menu you cannot change the
Satellite Name.
Automatic Skip
Option to search only Free-To-Air services.
The picture on the right tries to search with varying Frequency,
Symbol Rate and FEC etc.
Search Type
• You can select one of two modes(Quick or Detail).
• When you select Quick mode, it searches the service by search
parameters that is preset.
• When you select Detail mode, it searches the service through all
field of tuner(950 - 2150MHz).
GB32
Download from Www.Somanuals.com. All Manuals Search And Download.
Detail Mode
The pre-fixed symbol rate list is changed according to Antenna
Alternative and Satellite Name. If you want to add or change it,
press the Red(
)button.
** The value of Pre-fixed symbol rates can not be editable.
(22000, 27500)
The picture of the Symbol Rate Add/Change mode is as follows:
1. When you press the Red(
)button after entered to detail
mode from search type, yellow box will be trimmed with red
edges meaning edit is possible.
2. You can easily put optional value with using Numeric
buttons(0~9).
3. Press the Red(
)button for confirmation, and you will
successfully exit from input mode.
If press the
button at symbol rate value input mode,
the value will be confirmed, and if you moves left or right
column use the
symbol rate to input. Then press the
Red( )button to exit from input mode.
buttons, you can differ values of
and the
To delete a Symbol Rate in the above list, press the
0 (Numeric button) in the selected position and then the symbol rate
disappears. The range of Symbol Rate that is input additionally is
16-30Ms/s.
Note : The user should select the Satellite name in Antenna
Setting menu. When the user types the Satellite Name
separately, the search type is fixed to the Detail mode.
Press the
button anywhere to start Automatic Search.
The picture during searching is as follows.
The picture searches with varying frequency, Symbol Rate and
FEC etc. Satellite Name is the name that the user selects to
correspond with Antenna Alternative of Antenna Setting.
The progress bar(%) appears on bottom of the picture.
During the search, services that are found are displayed as follows:
1. Press the
button during Automatic Search to stop search.
2. After the search is finished, the appearite message appears.
3. Press the
button to return Service Search menu.
GB33
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu Guide
3-4. Status
STB Status
Displays the information of H/W Version, S/W Version, Loader
Version and so on.
Signal Detection
Shows the Signal Level(AGC level) and Signal Quality(BER) of
the current service and is help to the initial antenna setting.
STB Upgrade
You can download and upgrade the software of this STB via
a satellite when the software of new version is released.
Do not turn off the STB during downloading.
When the power is switched OFF, turn on the STB and the
process will be continued.
GB34
Download from Www.Somanuals.com. All Manuals Search And Download.
3-5. Conditional Access (for Nagravision Embedded)
This menu allows the user to view the information on the
Smart card and Nagravision Conditional Access system such as
version and serial number of Smart card.
PPV purchase list
If you perchased events in advance, the entitlements of Pay Per
View events will be displayed.(ID, event name, service name,
start time, status and cost)
Credit information
Displays the Credit information. (ID, credit and status)
System information
Displays the System information.
(Smart card serial number, IRD serial number, Smart card version,
Smart card revision, Conditional Access software version and
Conditional Access software revision.)
GB35
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu Guide
3-6. Default Setting
Reset STB to the default start set in the factory.
0 0 0 0
Enter the PIN Code ‘
’ and the message “The default values
are restored” will appear on the center of screen.
If you want to restore again, select “OK”. Otherwise, select “EXIT”.
4. Utility
STB supports additional functions such as Calendar and
Biorythm.
At the Biorhythm use the
buttons to adjust your birth
year and date to see your current biorhythm status.
GB36
Download from Www.Somanuals.com. All Manuals Search And Download.
Motorised System
DiSEqC 1.2 User Instructions
If you have a DiSEqC 1.2 motorised system, then you can use the DiSEqC 1.2 functions available.
The following instruction describes how to use the DiSEqC 1.2 functions to store the positions of the
satellites and to search for the services(STAB Rotor Sat motor recommended).
1. Satellite Setting Menu Options
When DiSEqC Motorised System is Enabled in the Antenna Setting, a new menu is available for
configuring the motor. This menu is called Satellite Setting and is accessed by pressing the OK
button while the option Antenna Alternative is highlighted in the Manual Search menu.
The following options are available on the Satellite Setting menu.
Satellite Name
A selection of satellite names that can be used to identify a motor position. If the satellite name you
require is not available, please use other. In installer mode the Satellite Name Reference refers to the
0 position of the motor.
Movement
In user mode this is used to fine-tune the position of the motor for better reception.
In Installer mode this is used to search for the position of a satellite manually.
Motor Control
• Search : Searches for services on the chosen transponder.
• Goto : Moves the motor to the stored position of the selected satellite name.
• Store : Stores the current position of the motor for the selected satellite name.
• Reset : Resets all stored positions of the motor relative to the 0 position.(Installer mode only)
DiSEqC Command Mode
Changes the current mode between Installer and User.
2. Setting your Receiver for DiSEqC 1.2
You must set your receiver up so that it is ready to use DiSEqC 1.2. To do so, do as follows
1. Press the MENU(
)button, to display the Main Menu.
2. Select Service Searching option and press OK button,
to display the Service Searching menu.
3. Select Antenna Setting option and press OK button,
to display the Antenna Setting menu.
4. You must set up a separate antenna alternative for each
satellite position required.
5. Select the name of the satellite you wish to use.
6. Select the correct LNB frequency for the LNB you are using.
7. Set the Motorised System to Enable using the
8. The option DiSEqC Input Selection should now be disabled. This option is used for DiSEqC 1.0
and cannot be used in conjunction with DiSEqC 1.2. Your receiver is now ready to use
DiSEqC 1.2. To return to the Main Menu, use the EXIT button until you are at the Main menu.
buttons.
GB37
Download from Www.Somanuals.com. All Manuals Search And Download.
Motorised System
3. Initial Satellite Position Search
This is required when you first set your receiver up to use DiSEqC 1.2 and sets the positions of all
pre-programmed satellites.
1. Make sure your motor is installed correctly with the calibrations
adjusted for the region you are situated.
(Please consult the user manual for your motor.)
2. Make sure your receiver is set up to use DiSEqC 1.2.
(see section 2 above).
3. On the Main Menu, select Service Searching option and press
the OK button, you should now see the Service Searching
menu.
4. Highlight the option Antenna Alternative and press the OK
button to display the Satellite Setting menu.
5. Highlight the DiSEqC Command Mode option and use the
buttons to change the value to
Installer and press the OK button.
6. Highlight the Motor Control option and use the
buttons to change the value to reset and
press the OK button.
7. You will now see a warning message, press the OK button to continue. All motor positions of the
pre-programmed satellites should now be correct. If you have any other make or model of
DiSEqC 1.2 motor then you may need to store the satellite positions in yourself(Please refer to
the user manual for your motor).
8. Highlight the DiSEqC Command Mode option and use the buttons to change the value to User
and press the OK button.
9. You should now be ready to start storing services for the various satellites(see 5 onwards).
4. Motor Limit Setting
Use this option to set the East and West limits of the motor. This should be used to prevent your dish
from hitting anything that may be obstructing the path of the dish.
1. On the Main menu, select Service Searching option and press the OK button.
You should now see the Service Searching menu.
2. Select Manual Search option and press the OK button, you
should now see the Manual Search menu.
3. Highlight the Antenna Alternative option and press the
OK button. You should now be in the Satellite Settings menu.
4. Press the
5. Highlight the Limit Setting option and use the
button to access the Motor Limit Setting menu.
buttons to
disable this.(Warning: When this option is disabled your motor
will be able to move beyond any limits that have been
stored - please take care in case there are anything obstructing
the path of your dish.)
GB38
Download from Www.Somanuals.com. All Manuals Search And Download.
6. To set the East Limit:
a) Select Movement and use the
buttons to move your
motor East or West until the motor is at the position you wish
to use as your East Limit. Use the
motor at the correct position.
buttons to stop the
b) Highlight the Store East Limit option and press the OK button
to store the current position as your East Limit.
To set the West Limit:
a) Select Movement and use the
motor East or West until the motor is at the position you wish to use as your West Limit.
Use the buttons to stop the motor at the correct position.
buttons to move your
b) Highlight the Store West Limit option and press the OK button to store the current position as your
West Limit.
5. Manual Satellite Search
The purpose of this is to set the motor position for each satellite manually.
This is useful if the satellite you require is not available from the pre-programmed list(see 3 above).
To do this, you must access the Satellite Settings menu. Do as follows ;
1. Select Service Searching from the main menu and press the OK button, to display the Service
Searching menu.
2. Select the Manual Search option and press the OK button, to display the Manual Search menu.
Select the relevant Antenna Alternative that you are using for this satellite.
3. Enter the Frequency, Polarisation, Symbol Rate and FEC of a transponder on the satellite you wish
to find. This transponder information should be unique to this satellite.
4. Select the Antenna Alternative option and press the OK button, to display the Satellite Settings
menu.
5. Highlight the option DiSEqC Command Mode and using the
buttons change this to Installer.
6. Highlight the option Satellite name and use the buttons to select the satellite you want to find,
use others if the name of the satellite you want does not appear.
7. When you have selected the satellite you wish to find, go down to the Movement option and again
using the
buttons to start the motor moving.
8. You should move the motor as far west as possible and the move it east so that you cover the
complete movement range of the motor.
9. During the move from west to east the Signal Quality bar should register a signal once.
This is the position of the satellite. If there are two or more different positions which registers a
signal, then you must choose another frequency that is unique to the satellite you want.
10. Use the Signal level and Strength Quality bar at the bottom of the screen to judge the best
position of the dish.
11. Use the
buttons to stop the motor when required.
12. When you have the best position of the dish go to the Motor Control option and using the
buttons select store and press the OK button. The position of the satellite should now be stored.
13. If you do not store this position, it will be lost when you exit the menu.
14. Repeat the process for each satellite if required, remembering to use a different antenna
alternative for each satellite.
GB39
Download from Www.Somanuals.com. All Manuals Search And Download.
Motorised System
6. Moving to a pre-set satellite
Once you have stored the positions of the satellites you want(see left below) you can now search for
the services transmitted from them. Before you can do this, you must move the motor to the
position of the satellite you wish to search. To do this, you must access the Satellite Settings menu.
Do as follows ;
1. Select Service Searching from the Main Menu and press the OK button, to display the Service
Searching menu.
2. Select the Manual Search option and press the OK button, to display the Manual Search menu.
3. Select the Antenna Alternative option and press the OK button, to display the Satellite Settings
menu.
4. In the Satellite Settings menu ensure that you have DiSEqC Command Mode option set to User.
5. Highlight the option Satellite Name and use the
to view.
buttons to select the satellite you want
6. When you have selected the satellite you wish to view, go down to the Motor Control option and
again using the buttons select go to and press the OK button.
7. The motor will now move to the position of the selected satellite.
8. The Movement option is used to fine-tune the position of the motor.
9. When using the Movement option for fine-tuning, you must remember to store the changes you
have made or else these will be lost.
7. Searching for services on your selected Satellite
Once you have moved the motor into position, you can search for the channels transmitted from the
relevant satellite. To search for services on your new selected satellite, Do as follows ;
1. Move the motor to the position of the satellite you wish to
search.(see section 6 above)
2. Select the service searching from the Main Menu and press the
OK button. To display the Service Searching menu.
3. Select the manual search option and press the OK button to
display the Manual Search menu.
4. Now enter the Frequency and Symbol Rate using the
NUMERIC buttons(0~9). Next enter the Polarisation and FEC
values using the
buttons.
5. When you have entered all these details in, press the OK button
and the search will begin.
6. When the search has finished, press the OK button to view.
7. Repeat the process for all the transponders you want from this
satellite.
GB40
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Automatic Search
It is possible to use automatic search using the DiSEqC 1.2 motorised system.
1. Ensure that the positions for the satellite you want to search is correct.(see Section 3 and 5
above)
2. In the Main Menu, select the option channel searching and press the OK button.
3. In the Service Searching menu, select the Antenna Alternative that you have set for this
satellite.
4. When you search new services, please refer to Automatic Search of page GB32.
5. When the search has finished, press the OK button to store and view the services.
Now that you have stored all the positions of the satellites and searched for all the services you
want, you can now use your receiver as normal. When you change to a service that is being
transmitted from a different satellite, you will have to wait a few seconds to allow the motor to move
into position to receive the new service.
GB41
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
Problem
Solution
About STB
Does not display any LED • Check the main power cable and check that it is plugged into a suitable power outlet.
on the front panel or STB
has no power.
• Check whether STB is in Standby mode.
No Picture
• Ensure that the STB is switched on (see above).
• Check the video output port (RCA/RF) is firmly connected to the TV or VCR.
• Check that you have selected the correct channel or Video Output on your TV.
• Check the brightness level of the TV.
Poor picture quality
No Sound
• See “No Picture” above.
• Check the signal level, if this is low then try adjusting the alignment of your dish.
• See “No Picture” above.
• Check the volume level of the TV and STB.
• Check the Mute status of the TV and STB.
Remote Control does not
operate
• Point remote control directly towards the STB.
• Check and replace batteries.
On-Screen Error Messages
No or Bad Signal
• Check the LNB - replace LNB if necessary.
• Check the cable from the LNB.
• Check the position of the dish - realign dish if necessary.
• If you are using a DiSEqC 1.0 switch, check that you have connected the LNBs to
the correct connections on the switch.
• Check the “Signal Level” and the “Signal Quality” in the Signal Status menu.
Service Search
“No Signal” in manual
search
• Check the “Signal Level” and the “Signal Quality” in the Signal Status menu.
• Check the LNB - replace LNB if necessary.
• Check the cable from the LNB.
• Check the position of the dish - realign dish if necessary.
• DiSEqC 1.0
Check that you have connected the LNBs to the correct connections on the switch.
Check that you have set the connected setting in the Antenna Setting menu.
GB42
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Amber only:
Solution
LED Error Message
• Check whether the system ID is different for Software and STB.
Invalid system ID
Amber & Red:
Incorrect data block CRC
error
• You need to contact your retail shop.
Amber & Red & Green:
Incorrect application CRC
error
• You need to contact your retail shop.
• If you can’t solve the problem even referring this Troubleshooting Guide, contact us
via our homepage.
GB43
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Map
GB44
Download from Www.Somanuals.com. All Manuals Search And Download.
GB45
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
Conditional Access Interface
Nagravision Embedded
1 Slot Smart Card
Tuner & Channel
Input Connector
Frequency Range
Input Impedance
Signal Level
IF
F-type, IEC 169-24, Female
950 MHz to 2150 MHz
75Ω unbalanced
-25 to -65dBm
480 MHz
IF Band width
LNB Power &
Polarisation
36 MHz
Vertical : +11V
Horizontal : +15V
Current : 300mA Max. Overload Protection
22 KHz Tone
Frequency : 22 ± 4KHz
Amplitude : 0.6 ± 0.2V
DiSEqC Control
Demodulation
Input Symbol Rate
FEC Decorder
Version 1.0
QPSK
1-45 Ms/s, SCPC and MCPC capable
Convolutional Code Rate 1/2, 2/3, 3/4, 5/6 and 7/8
with Constraint Length K=7
MPEG Transport Stream A/V Decoding
Transport Stream
MPEG-2 ISO/IEC 13818
Transport stream specification
MPEG-2 MP@ML
Profile Level
Input Rate
15 Mbit/s Max
Aspect Ratio
Video Resolution
Audio Decoding
Audio Mode
Sampling
4:3, 16:9
720 x 480
MPEG/MusiCam Layer I & II
Single channel / Dual channel / Joint stereo / Stereo
32, 44.1 and 48KHz
Memory
Main Processor
Flash Memory
TMIPS R3930(81MHz)
3Mbyte
Graphic(MPEG) &
System DRAM
4Mbyte
GB46
Download from Www.Somanuals.com. All Manuals Search And Download.
A/V & Data In/Out
VIDEO
RCA/Cinch
AUDIO R/L
RCA/Cinch Volume and Mute Control
(Resolution : 20 bits DAC, Max. 2 Vrms)
Transfer rate 115,200 bps, 9pin D-sub Type
RS-232C
RF-Modulator
RF-Connector
Frequency
Output Channel
TV Standard
Preset Channel
75Ω, IEC 169-2, Male / Female
61.25 MHz, 67.25 MHz
CH3, 4 for the Remodulator
NTSC-J
CH3. Software changeable by Menu.
Power Supply
Input Voltage
Type
100V AC, 50/60 Hz
SMPS
Power Consumption
Standby Power
Protection
Max. 30W
≤
8W
Separate internal fuse. The input shall have lightening Protection
Physical Specification
Size (W x H x D)
Weight (Net)
260
Around 1.3 kg
x
50
x
180 mm
Operating Temp
Storage Temp
Storage Humidity
0°C to + 45°C
-10°C to + 70°C
5% ~ 95% RH (Non-Condensing)
• Please note : The specification of the STB may be changed without notice in
advance.
GB47
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|