Portable Basketball System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
REQUIRED TOOLS AND MATERIALS:
WARNING!
• Two People
• Wood Board (Scrap)
• Tape Measure
• Step Ladder 8 ft. (2.4 m)
• Tape
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
• Garden Hose or Sand 360 lb. (163 kg)
• Hammer
• Wrenches: (Two) 3/4”, (One) 1/2” (Two) 9/16”or
equivalent sockets, (One) 1/2” Deep well socket
with extension and socket wrench, 3/8 socket
• Support Table
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO
PROPERTY.
• Phillips Head Screwdriver
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-333 061
Internet Address: http://www.huffysports.com
1
03/04
P/N 21147703
© COPYRIGHT 2000 by HUFFY SPORTS
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY,
PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper
and complete assembly, use and supervision is essential for proper operation and to reduce the risk of
accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and
operated properly.
•
•
If using a ladder during assembly, use extreme caution.
Check base regularly for leakage. Slow leaks could cause the system to tip over
unexpectedly
•
Seat the pole sections properly (if applicable). Failure to do so could allow the pole
sections to seperate during play and/or during transport of the system.
Climate, corrosion or misuse could result in system failure.
If technical assistance is required, contact Huffy Sports.
Minimum operational height is 6’6” (1.98m) to the bottom of backboard.
•
•
•
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this unit.
NOTICE TO ASSEMBLERS
ALL Huffy Sports basketball Systems, including those used for DISPLAYS, MUST be assembled
and ballasted with sand or water according to instructions. Failure to follow instructions could
result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
IMPORTANT!
Remove all contents from boxes.
Be sure to check inside pole sections;
hardware and additional parts are packed inside.
3
03/04
P/N 21147703
Download from Www.Somanuals.com. All Manuals Search And Download.
Get to know the basic parts of your basketball system.....
FRONT
BACK
BACKBOARD
RIM
ELEVATOR
ASSEMBLY
TOP POLE
BOTTOM
POLE
MIDDLE POLE
STRUTS
FRONT
COVER
BASE
WHEEL
CARRIAGE
ASSEMBLY
4
P/N 21147703 03/04
Download from Www.Somanuals.com. All Manuals Search And Download.
Item Qty Part No. Description
1
2
3
4
5
6
7
8
1
1
1
1
1
2
2
1
6
18
21*
1
2
2
4
2
1
1
1
8
7*
2
1
2
1
1
1
1
4
2
4
2
2
2
2
1
2
1
6*
1
4
1
2
4
2
4
1
2
4
6
1
1
1
2
1
1
12
1
4
908026
908107
908015
900223
206940
226403
206938
206660
203156
203218
203100
201581
202662
203099
203223
906410
200516
206990
203038
202862
206340
203053
204872
204858
207103
204853
204850
204832
206360
200874
201124
900867
904807
900183
204859
203124
203617
201965
203257
Top Pole Section
Middle Pole Section (with Label)
Bottom Pole Section
Wheel Bracket
Axle
Wheel
Pushnut
Base
Hex Bolt, 5/16-18 x 1
Flat Washer, 5/16
Hex-Flange Nut, 5/16-18
Pole Bracket
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
Hex Bolt, 5/16-18 x 4.5
Locknut, 5/16-18
Carriage Bolt, 5/16-18 x 1
Tank Strut
Bolt Cover
Reinforcement Bracket
Carriage Bolt, 5/16-18 x 2-3/4 Long
Spacer, Plastic, 1.19" Long
Locknut, 1/2-13
Carriage Bolt, 5/16-18 x 4 Long
Label, Height Indicator
Spacer, Plastic, Biscuit
Pole Cap
Lanyard, Black Coil
Pin, Locking
Bracket, Pole Mount
Hex Bolt, 3/8-16 x 2.625
Spacer, Metal, 1.53" Long
Locknut, 3/8-16
Plate, Triangle
Elevator Tube, Upper - Short
Elevator Tube, Lower - Long
Cover, Pin Slide
Tie Down Stake
Base Plug
Front Cover
Tie Straps
Rim
Washer, Flat
203309
201252
204857
203232
900964
201681
202605
204838
201682
202532
904866
204855
204856
203103
204803
204444
201219
Label, Height Adj and Moving
Spacer, Metal 1/2” O.D. x 1.44 Long
Flat Washer, 3/8
Bracket, Backboard Support
Spacer, Plastic, .530 I.D. x .88 Long
Bolt, Hex, 1/2-13 x 4-1/4" Long
Spring, Counter Balance
Spacer, .530 I.D. x 1.875
Bolt, Hex, 1/2-13 x 9.5"
Height Adjustment Rod
Handle, Left
Handle, Right
Carriage Bolt, 5/16-18 x 2 Long
Screw, Phillips Head
Rope
Smart Clips, Net Holder
Net
205528
Bolt, Hex Flange, 5/16-18 x 1" Long
WARRANTY CARD:
Please remember to complete your product
registration form either on-line at:
www.huffysports.com/warrantycard or mail-in
the enclosed postcard.
* You may have extra parts with this model.
5
03/04
P/N 21147703
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (BOLTS & SCREWS)
Item #13 (2)
Item #9 (6)
Item #47 (1)
Item #15 (4)
Item #29 (4)
Item #54 (2)
Item #55 (1)
Item #19 (1)
Item #50 (6)
Item #59 (4)
Item #22 (2)
HARDWARE IDENTIFIER (NUTS, WASHERS & METAL SPACERS)
Item #14 (2)
Item #11 (21)
Item #21 (7)
Item #31 (4)
Item #30 (2)
Item #44 (4)
Item #10 (18)
Item #43 (2)
Item #41 (4)
6
P/N 21147703 03/04
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (PLASTIC SPACERS & CAPS)
Item #46 (4)
Item #17 (1)
Item #7 (2)
Item #20 (8)
Item #49 (4)
Item #24 (2)
HEIGHT ADJUSTMENT
TO ADJUST BACKBOARD:
1
3
1. While holding handle, remove pin.
2. Move elevator up or down to
desired height.
2
3. Replace pin full length to lock
system at desired height.
2
MOVING SYSTEM
1. Adjust basketball backboard
height to lowest position.
1
2. While holding pole, rotate
basketball system forward
until wheels engage with
ground.
3. Move basketball system to
desired location.
2
4. Carefully rotate basketball
system upright.
3
4
5. Reattach ground restraint and
check system for stability.
201252
2/99
Item #42 (1)
7
03/04
P/N 21147703
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU START!
To ensure optimal playability of backboard system, a close tolerance fit between the elevator
components and hardware is required. Test fit large bolts into large holes of elevator tubes,
backboard brackets and triangle plates. Carefully rock them in a circular motion to ream out
any excess paint from holes if necessary.
AVANT DE COMMENCER !
Pour garantir l'utilisation optimale du panneau, les composants du système élévateur et la visserie doivent être bien
ajustés (serrés). À titre d'essai, insérez les gros boulons dans les gros trous des tubes du système élévateur, des supports
du panneau et des plaques triangulaires. Basculez-les avec précaution en imprimant un mouvement circulaire pour
éliminer l'excédent de peinture, si nécessaire.
¡ANTES DE COMENZAR!
Para asegurar el óptimo rendimiento del sistema del respaldo en el juego, se requiere un ajuste de tolerancia estrecha
entre los componentes del elevador y el herraje. Pruebe el ajuste de los pernos grandes en los orificios grandes de los
tubos elevadores, soportes del respaldo y placas triangulares. Cuidadosamente muévalos en círculos para eliminar
cualquier exceso de pintura, si es necesario.
VORBEREITENDE MASSNAHMEN
Um sicherzustellen, dass das Korbwandsystem optimal für den Spielbetrieb geeignet ist, müssen die Komponenten der
Verlängerungsvorrichtung und die verschiedenen Befestigungsteile fest miteinander verschraubt werden. Große Schrauben
zur Probe in die großen Löcher der Verlängerungsrohre, Korbwandklammern und Dreiecksplatte stecken und diese
vorsichtig in einer Kreisbewegung hin- und herbewegen, um eventuelle Farbrückstände aus den Bohrungen zu entfernen.
8
P/N 21147703 03/04
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION A: ASSEMBLE THE POLES
1.
Correctly identify each pole section.
1
I.D. Label
3
2
I.D. Label
WARNING
LABEL
Align dimple of top pole with slot of middle pole. While maintaining alignment, bounce middle pole
(2) into top pole section (1) using a wood scrap as shown until top pole no longer moves toward
pole identification mark on middle pole.
2.
CAUTION!
THE IDENTIFICATION STICKER IS
LOCATED 5" FROM THE END OF
THE POLE. WHEN PROPERLY
POUNDED TOGETHER, THE POLE
SECTIONS SHOULD HAVE A 3-1/2"
MINIMUM OVERLAP, LEAVING 1-
1/2" BETWEEN THE OVERLAPPING
POLE AND THE IDENTIFICATION
STICKER.
NOTE:
POLE SECTIONS
SHOULD HAVE A
3-1/2" (9 CM) MINIMUM
OVERLAP.
2
IDENTIFICATION
STICKER
2
m i d d l e p o l e
POLE
IDENTIFICATION
MARK
5"
1
1
2
IDENTIFICATION
STICKER
m i d d l e p o l e
1-1/2"
WOOD SCRAP
(NOT SUPPLIED)
1
9
03/04
P/N 21147703
Download from Www.Somanuals.com. All Manuals Search And Download.
Align dimple of middle pole with slot of bottom pole. While maintaining alignment, bounce
top and middle pole assembly (1 & 2) onto lower pole section (3) as shown until they no
longer move toward pole identification mark.
3.
CAUTION!
2
THE IDENTIFICATION STICKER IS
LOCATED 5" FROM THE END OF
THE POLE. WHEN PROPERLY
POUNDED TOGETHER, THE POLE
SECTIONS SHOULD HAVE A 3-1/2"
MINIMUM OVERLAP, LEAVING 1-
1/2" BETWEEN THE OVERLAPPING
POLE AND THE IDENTIFICATION
STICKER.
5"
Bottom Pole
IDENTIFICATION
STICKER
3
NOTE:
POLE SECTIONS
SHOULD HAVE A
3-1/2" (9 CM) MINIMUM
OVERLAP.
2
1
1-1/2"
IDENTIFICATION
STICKER
Bottom Pole
3
POLE
IDENTIFICATION
MARK
2
RODS SHOWN ARE
FOR VISUAL
REPRESENTATION
OF ALIGNMENT
AND ARE NOT
SUPPLIED WITH
THE HARDWARE
3
IMPORTANT!:
Holes in top (1) and bottom
pole (3) sections MUST
align to correctly position
elevator system toward
playing surface.
WOOD SCRAP
(NOT SUPPLIED)
10
P/N 21147703 03/04
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION B: ASSEMBLE THE BASE
This is what your system will look like
when you’ve finished this section:
WARNING
IMPORTANT!:
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT
IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
Owner must ensure that all players know and follow
these rules for safe operation of the system.
•
•
DO NOT HANG on the rim or any part of the system
including backboard, support braces or net.
During play, especially when performing dunk type
activities, keep player's face away from the backboard, rim
and net. Serious injury could occur if teeth/face come in
contact with backboard, rim or net.
•
•
Do not slide, climb, shake or play on base and/or pole.
After assembly is complete, fill system completely with
water or sand and stake to the ground. Never leave system
in an upright position without filling base with weight, as
system may tip over causing injuries.
•
When adjusting height or moving system, keep hands and
fingers away from moving parts.
Do not allow children to move or adjust system.
During play, do not wear jewelry (rings, watches, necklaces,
etc.). Objects may entangle in net.
Surface beneath the base must be smooth and free of
gravel or other sharp objects. Punctures cause leakage and
could cause system to tip over.
Keep organic material away from pole base. Grass, litter,
etc. could cause corrosion and/or deterioration.
Check pole system for signs of corrosion (rust, pitting,
chipping) and repaint with exterior enamel paint. If rust has
penetrated through the steel anywhere, replace pole
immediately.
Check system before each use for proper ballast, loose
hardware, excessive wear and signs corrosion and repair
before use.
Check system before each use for instability.
Do not use system during windy and/or severe weather
conditions; system may tip over. Place system in the
storage position and/or in an area protected from the wind
and free from personal property and/or overhead wires.
Never play on damaged equipment.
See instruction manual for proper installation and
maintenance.
When moving system, use caution to keep mechanism from
shifting.
THE WARNING
LABEL MUST
BE VISIBLE
FROM PLAYING
AREA
•
•
•
•
•
•
•
•
•
•
•
•
•
Keep pole top covered with cap at all times.
Do not allow water in tank to freeze. During sub-freezing
weather add non-toxic antifreeze, sand or empty tank
completely and store. (Do not use salt.)
Use extreme caution if placing system on sloped surface.
System may tip over more easily.
•
In the U.S.:1-800-558-5234 and Canada: 1-800-284-8339
201241
2/99
HARDWARE USED IN THIS SECTION
(not actual size)
TOOLS REQUIRED FOR THIS SECTION
(2) 1/2” AND (2) 9/16" Wrenches
Item #13
AND/OR
(2) Socket Wrenches and Sockets
Item #9
Item #14
Item #15
Item #17
Item #11
1/2”
9/16”
AND
a Hammer or
Mallet
Item #10
Item #7
11
03/04
P/N 21147703
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach pole assembly to base using carriage
bolts (15) washers(10) and nuts (11) as
shown. Two people are required for this step.
Assemble pole bracket (12)
to pole (3) using bolt (13)
and locknut (14) as shown.
1.
2.
IMPORTANT!:
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
THE CUT CORNERS OF
THE POLE BRACKET
NEED TO FACE
TOWARD THE BACK OF
THE BASE AS SHOWN.
13
14
15
12
IMPORTANT!:
DO NOT OVER
TIGHTEN
10
11
12
P/N 21147703 03/04
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure tank struts (16) to pole as shown.
Nut should be tightened until flush (even)
with locknuts outer edge. Place cap (17)
over exposed end of bolt as shown.
3.
10
13
17
14
10
16
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
IMPORTANT!:
Rotate non-secured ends of tank struts (16) outward to mounting holes in tank as
shown.Secure ends of tank struts (16) to tank as shown. Repeat for opposite side.
4.
9
16
16
10
10
11
13
03/04
P/N 21147703
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert axle (5) through wheel bracket (4). Secure wheels (6) to axle using
pushnuts (7). Carefully tap pushnuts onto axle with hammer or mallet
5.
IMPORTANT!:
6
7
4
5
6
7
SIDE OF WHEEL WITH
LONGER PLASTIC
AXLE NEEDS TO FACE
THE WHEEL BRACKET.
Install wheel assembly to base (8) using
bolts(9), washers(10) and nuts (11) as shown.
6.
9
9
10
10
8
10
11
14
P/N 21147703 03/04
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION C: ASSEMBLE THE ELEVATOR & BACKBOARD
This is what your system will look like
when you’ve finished this section:
HARDWARE USED IN THIS SECTION
TOOLS REQUIRED FOR THIS SECTION
(not actual size)
Item #55
(2) 1/2”, (2) 9/16"” AND (2) 3/4”
Item #29
Wrenches
Item #54
Item #19
Item #21
AND/OR
Item #50
(2) Socket Wrenches and Sockets
Item #31
Item #11
Item #24
Item #44
Item #59
3/4”
1/2”
9/16”
Item #22
Item #43
Item #30
15
03/04
P/N 21147703
Download from Www.Somanuals.com. All Manuals Search And Download.
Install pole mount bracket (28) and reinforcement bracket (18) with carriage bolts
(22) as shown. Tighten flange nuts (11) completely.
1.
22
18
1
22
28
11
11
Attach spacers (24, 43) to pole mount bracket (28) with bolts (29), washers (44),
and lock nuts (31) as shown. IMPORTANT! Tighten just until washers (44) stop
moving.
2.
28
44
31
44
44
44
24
29
43
43
24
16
P/N 21147703 03/04
Download from Www.Somanuals.com. All Manuals Search And Download.
Assemble lanyard (26) to locking pin (27) as shown (FIG A). Attach covers (35) onto
pole mount bracket (28) with carriage bolt (19) and nut (11) as shown.
3.
35
11
28
35
FIG. A
IMPORTANT!:
Loop end of pin
lanyard (26) over
carriage bolt (19)
as it passes
26
19
19
through the pole
mount bracket
(28) during this
assembly.
26
27
27
Apply logo and height indicator labels (23) to
adjustment rod (51) as shown. Attach handle
parts (52, 53) to adjustment rod with screw
(55), carriage bolts (54), and flange nuts (11)
as shown.
4.
23
51
IMPORTANT!:
Indicator labels
should be applied
as close to holes
as possible to
23
prevent labels from
being damaged
during height
adjustment.
11
53
54
55
11
52
54
17
03/04
P/N 21147703
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert handle assembly through pole mount assembly as
shown. Lock pole assembly in place at the 10’ (3.05 m)
mark with pin (27).
5.
27
30
31
30
31
Assemble backboard brackets (45)
using spacers (30), bolts (29), and
nuts (31) as shown.
29
6.
IMPORTANT!:
KEEP HARDWARE LOOSE
UNTIL AFTER STEP 8 IS
COMPLETED.
29
45
30
45
31
29
Face of Backboard
18
P/N 21147703 03/04
Download from Www.Somanuals.com. All Manuals Search And Download.
Identify elevator tubes (33 & 34).
7.
Toward
Board
Toward
Pole
33
34
Upper Elevator tube
Lower Elevator tube
Toward
Board
Toward
Pole
Attach lower elevator tubes (34) and counter balance spring (48) to backboard
support brackets (45) using spacers (46 & 49), bolt (50), and nut (21) as shown.
NOTE: Rim mounting nuts and bolts supplied with rim hardware.
NOTE: DO NOT use washers here on spring return style rims.
46
21
45
48
34
49
49
48
50
34
Refer To
Instructions
Included With Rim
Hardware For Rim
Assembly.
41
59
40
19
03/04
P/N 21147703
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach upper elevator tubes (33) to backboard support brackets (45) using
spacers (46 & 49), bolt (50), and nut (21) as shown.
8.
IMPORTANT!:
TIGHTEN ALL HARDWARE
FROM STEP 6 - 8 AFTER
THIS ASSEMBLY IS
COMPLETED.
46
21
49
45
33
49
50
33
46
21
49
33
49
50
33
20
P/N 21147703 03/04
Download from Www.Somanuals.com. All Manuals Search And Download.
Support pole on sawhorse. Attach backboard assembly to top pole section (1)
as shown. Install pole cap (25).
9.
WARNING!
USE CAUTION; ELEVATOR
21
ASSEMBLY IS HEAVY.
34
TWO PEOPLE REQUIRED FOR
THIS PROCEDURE. FAILURE TO
FOLLOW THIS WARNING
COULD RESULT IN SERIOUS
INJURY AND/OR PROPERTY
DAMAGE.
20
1
21
32
25
32
20
47
34
50
10. Install upper elevator tubes (33) to triangle plates (32) as shown. Install handle
assembly to lower elevator tubes (34) using bolt (50), spacers (20), and nut (21) as
shown.
21
21
20
33
51
20
1
20
34
32
NOTE:
34
Before going on to
next step, set
20
50
adjustable system
assembly to the 10’
(3.05 m) setting.
50
33
21
03/04
P/N 21147703
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert bolt (50) through left side upper elevator tube (33), then stretch spring
(48) onto bolt (50). Insert bolt (50) through right side upper elevator tube (33)
and secure with nut (21).
11.
WARNING!
USE EYE PROTECTION
WHEN INSTALLING
SPRINGS.
21
33
48
50
33
48
51
22
P/N 21147703 03/04
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION D: SECURING THE SYSTEM
1. Roll assembly to desired playing area. Secure assembly to ground using rope (56)
and tie down stake (36). Fill base (8) with water (approx. 40 gallons) and snap fill
caps (37) in place.
WARNING!
DO NOT LEAVE
CAUTION!
ASSEMBLY UNATTENDED
WHEN EMPTY; IT MAY TIP
ADD TWO GALLONS (7.6
LITERS) OF NON-TOXIC
ANTIFREEZE IN SUB-
FREEZING CLIMATES.
OVER.
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT IN
SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
37
37
56
36
8
23
03/04
P/N 21147703
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION E: INSTALL FRONT COVER
Install front cover (38) by lining up stand-offs along the tank struts. Insert a tie strap
(39) through the top two and bottom two stand offs. Wrap tie straps around tank
struts as shown and secure tightly. Trim excess of tie strap as shown in FIG.A.
1.
38
STANDOFFS
FIG.A
39
24
P/N 21147703 03/04
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION F: NET INSTALLATION
1.
Install clips.
CLIP “ARM”
WARNING!
USE OF THIS PRODUCT
WITHOUT PROPER
INSTALLATION OF SMART
CLIPS®, OR WHEN ALL SMART
CLIPS® ARE NOT PRESENT
COULD RESULT IN BODILY
HARM. BE SURE TO FOLLOW
DIRECTIONS CAREFULLY.
CLIP “BODY”
40
Insert one “arm” of clip into ram as shown. Twist “body” of
clip slightly so that second “arm” slides over the top of the
first “arm” as shown.
Push in direction indicated by arrows.
57
A
Push second “arm” back and into ram as shown.
B
Twist “body” of clip slightly again to spread “arms” of clip.
Clip “arms” must be flat and touching edge to edge as
shown, not overlapping.
C
25
03/04
P/N 21147703
Download from Www.Somanuals.com. All Manuals Search And Download.
40
2.
SIDE VIEW
57
NETCLIP
58
NET
Insert net into bottom of clip as shown.
SIDE VIEW
Twist net until it snaps into position.
Net must be centered through clip.
NETCLIP
NET
26
P/N 21147703 03/04
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION G: APPLY HEIGHT AND MOVING LABEL
Apply Height Adjustment and Moving Label (42) to front of pole, where it is
clearly visible.
1.
42
HEIGHT ADJUSTMENT
TO ADJUST BACKBOARD:
1
3
1. While holding handle, remove pin.
2. Move elevator up or down to
desired height.
2
3. Replace pin full length to lock
system at desired height.
2
MOVING SYSTEM
1. Adjust basketball backboard
height to lowest position.
1
2. While holding pole, rotate
basketball system forward
until wheels engage with
ground.
3. Move basketball system to
desired location.
2
4. Carefully rotate basketball
system upright.
3
4
5. Reattach ground restraint and
check system for stability.
201252
2/99
27
03/04
P/N 21147703
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION H: HEIGHT ADJUSTMENT
A. While holding handle, remove pin (27).
B. Move elevator up or down to desired height.
1.
C. Replace pin (27) full length to lock system at desired height.
51
WARNING!
DO NOT ALLOW
CHILDREN TO
ADJUST HEIGHT.
27
A.
C.
B.
28
P/N 21147703 03/04
Download from Www.Somanuals.com. All Manuals Search And Download.
|