REQUIRED
MATERIALS:
Portable System
Owners Manual
•2 People
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
•Wood Board
(scrap)
•Sawhorse or
Support Table
•Garden Hose or Sand
Write Model Number
WARNING!
From Box Here:
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO
PROPERTY.
Toll-Free Customer Service Number for U.S: 1-800-558-5234,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-632 7921
Internet Address: http://www.huffysports.com
© COPYRIGHT 2005 by SPALDING
12/05
ID# M611701
1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR
PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper
and complete assembly, use, and supervision are essential for proper operation and to reduce the risk of
accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and
operated properly.
•
•
If using a ladder during assembly, use extreme caution.
Check base regularly for leakage. Slow leaks could cause the system to tip over
unexpectedly
•
Seat the pole sections properly (if applicable). Failure to do so could allow the pole
sections to separate during play and/or during transport of the system.
Climate, corrosion or misuse could result in system failure.
If technical assistance is required, contact Customer Service.
Minimum operational height is 6'-6" (1.98m) to the bottom of backboard.
•
•
•
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this unit.
NOTICE TO ASSEMBLERS
ALL basketball systems, including those used for DISPLAYS, MUST be assembled and ballasted
with sand or water according to instructions. Failure to follow instructions could result in
SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
IMPORTANT!
Remove all contents from boxes.
Be sure to check inside pole sections;
hardware and additional parts are packed inside.
WARRANTY CARD:
Please remember to complete your product registration form either on-
line at:
or mail-in the enclosed postcard.
12/05
ID# M611701
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Get to know the basic parts of your basketball system...
FRONT VIEW
BACK VIEW
BACKBOARD
RIM
ELEVATOR
ASSEMBLY
TOP POLE
MIDDLE POLE
STRUTS
BOTTOM
POLE
BASE
WHEEL
CARRIAGE
ASSEMBLY
4
ID# M611701
12/05
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Item Qty. Part No. Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
3
5
1
2
1
3
1
206646
200628
226401
908200
908246
900644
203041
Tank (Black)
Wheel Axle
Wheel
Top Pole Section
Middle Pole Section with Label
Bottom Pole Section Assembly
Nut, Hex Flange, 3/8-16
Net
Wheel Bracket
Spacer, Wheel Axle
Rim Bracket
201342
201651
902319
206219
266001
203617
Cap
Bolt, Carriage, 3/8-16 x 1.5 Long
Tank Cap
5E2356 Label, Moving System and Height Adjust.
203084
201344
Bolt, Carriage, 5/16-18 x 1.75 Long
Knob, Plastic, 3-sided
Rim
Bolt, Carriage 5/16-18 x 4
Backboard Mounting Bracket
Washer, .406 I.D. x 1.0 O.D.
Backboard
203053
900253
203309
* YOU MAY HAVE EXTRA PARTS WITH THIS MODEL.
12/05
ID# M611701
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS IDENTIFIER
- Actual Size
#13 (1)
#21 (3)
#16 (3)
#7 (1)
#19 (2)
#10 (2)
PARTS IDENTIFIER- Not Actual Size
#3 (2)
#1 (1)
#2 (1)
#8 (1)
#14 (1)
#9 (1)
#11 (1)
#12 (1)
#17 (5)
#18 (1)
#20 (1)
#22 (1)
6
ID# M611701
12/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Correctly identify each pole section. Poles have an identification sticker
that will be used as a reference point in the next step.
1.
Reference Stickers
4
5
6
TOP
MIDDLE
BOTTOM
12/05
ID# M611701
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT!
ONCE POLE SECTIONS ARE POUNDED TOGETHER- THEY CANNOT BE TAKEN APART
Align poles using alignment marks. First, pound top
and middle poles together by bouncing them on a scrap
piece of wood on the ground as shown in FIG A. until
CAUTION!
THE IDENTIFICATION STICKER IS
2.
LOCATED 5" FROM THE END OF
THE POLE. WHEN PROPERLY
POUNDED TOGETHER, THE POLE
SECTIONS SHOULD HAVE A 3-1/2"
MINIMUM OVERLAP, LEAVING 1-1/2"
BETWEEN THE OVERLAPPING
POLE AND THE IDENTIFICATION
STICKER.
they no longer move toward pole identification stickers.
THEN add bottom pole section and pound together in
the same way FIG B.
FIG. B.
FIG. A.
4
IMPORTANT!
DIMPLE
4
5
TROUGH
CANAL
1-1/2"
ID STICKER
ID
STICKER
5"
ID STICKER
DIMPLE
5
6
HOLE
Wood Scrap
(NOT SUPPLIED)
8
ID# M611701
12/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Install wheel axle (2) through wheel bracket (9) and install wheels (3) onto
wheel axle (2) with spacers (10) as shown.
3.
4.
IMPORTANT!:
9
2
3
10
THE SPACER (10) WILL
FIT LOOSELY UNTIL
SECURED INTO THE
CAVITY OF THE BASE.
Attach wheel carriage assembly to base (1) with bolt (13), washer (21), and nut (7)
as shown. FINGER TIGHTEN - NO TOOLS REQUIRED. Assembly will be fully
tightened in next step.
7
IMPORTANT!:
21
BE SURE THAT THE
SQUARE PORTION OF THE
CARRIAGE BOLT (13) IS
PROPERLY SEATED IN
THE SQUARE CUT-OUT OF
THE WHEEL BRACKET.
1
13
12/05
ID# M611701
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach pole assembly to tank assembly as shown. Secure pole assembly to tank
and wheel bracket by turning the pole assembly clockwise as shown. Tighten
pole completely and further rotate pole until struts are aligned correctly as shown
in FIG B.
5.
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT
IN SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
IMPORTANT!
The pole should be turned
approximately 7 complete
rotations to tighten properly.
When properly tightened, the
wheel bracket will be tight
against the base. An assistant
is recommended to hold the
base in place during this step.
FIG B
10
ID# M611701
12/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Rotate struts down and bend struts outward to line up with holes on base as shown.
Secure free ends of tank struts to tank with carriage bolt (16), washer (21), and
knob (17) as shown. Repeat for other side.
6.
WARNING!
KNOBS MUST BE TIGHTENED
COMPLETELY AND
CHECKED PERIODICALLY
FOR TIGHTNESS.
16
21
17
12/05
ID# M611701
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Pole bracket (20) will need to be lightly pressed into
backboard ribbing. Be sure to press completely into
place. Attach rim (18) to backboard (22) and pole
bracket (20) with knob (17), reinforcement
bracket (11), and carriage bolt (16) as shown.
Tighten knob completely.
7.
SAWHORSE OR SUPPORT TABLE
WARNING!
KNOB MUST BE TIGHTENED
COMPLETELY AND
CHECKED FOR TIGHTNESS
BEFORE EACH USE.
22
17
11
18
PRESS BRACKET (20)
INTO PLACE HERE
16
20
Carefully tip unit forward and slide
backboard assembly onto pole as shown.
SAWHORSE OR SUPPORT TABLE
12
ID# M611701
12/05
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach board assembly to pole with carriage
bolts (19) and knobs (17) as shown. Install pole
22
8. cap (12) as shown.
17
12
19
Install net (8).
9.
2.
4.
1.
3.
12/05
ID# M611701
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach height and moving
label (15) to front of pole as
shown. Regulation rim height
is 10 feet (3.05 m).
Place assembled unit in desired location. Fill
tank with water (26 gallons/98.4 liters) or
10. sand (approx. 360 lb./163 kg) and snap tank
cap (14) in place.
11.
CAUTION!
HEIGHT ADJUSTMENT
Rest unit on support table. Remove adjustment knobs (A)
and carriage bolts (B) to extend or retract backboard and rim.
Height adjustment from
7
1/2' to 10'.
CAUTION!
HEIGHT AND MOVING LABEL
MUST NOT OBSTRUCT
FACTORY ATTACHED
WARNING LABEL.
A
WARNING
Backboard
may rotate during
height adjustment.
ADD TWO GALLONS (7.6
LITERS) OF NON-TOXIC
ANTIFREEZE IN SUB-
FREEZING CLIMATES.
B
WARNING
Do not adjust height of system
in upright position. System must
be in down position to adjust
MOVING SYSTEM
1. While holding pole, rotate
basketball system forward
until wheels engage with
ground.
2. Move basketball system to
desired location.
3. Carefully rotate basketball
system upright.
1
4. Reattach ground restraint and
check system for stability.
2
3
200439
11/00
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT
IN SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
WARNING!
DO NOT LEAVE
ASSEMBLY UNATTENDED
WHEN EMPTY; IT MAY TIP
OVER.
14
15
10 feet
(3.05 m)
NOTE:
IF USING SAND:
2 GALLONS OF
ANTI-FREEZE IS
NOT REQUIRED
14
ID# M611701
12/05
Download from Www.Somanuals.com. All Manuals Search And Download.
|