Display System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Models
89225
&
89226
WARNING!
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
REQUIRED TOOLS AND
MATERIALS:
• 2 People
• Wrenches: (Two each) 7/16”, 1/2”, 9/16”, and 3/4” or Pliers
• Phillips Screwdriver
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO PROPERTY.
• 2 Step Ladders, 8 ft. (2.4 m)
IMPORTANT!
To ensure prompt and correct handling of any problems, or to answer any questions, please contact the Sample and
Display Technician at 1-800-558-5234.
P/N 21154401
01/04
1
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE TO ASSEMBLERS
ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled
and ballasted with sand or water according to the instructions. Failure to follow instructions
could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
IMPORTANT!
Remove all contents from boxes.
Be sure to check inside pole sections;
hardware and additional parts are packed inside.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY
RESULT IN SERIOUS INJURY,
PROPERTY DAMAGE AND WILL VOID WARRANTY.
This unit is intended for display purposes only and
should not be used for play.
To ensure safety, do not attempt to assemble this system without
following the instructions carefully. Check entire box and inside all
packing material for parts. Before beginning assembly, read the
instructions and identify parts in this document. Proper and
complete assembly, use and supervision is essential for proper
operation and to reduce the risk of accident or injury. A high
probability of serious injury exists if this system is not installed,
maintained, and operated properly.
• During assembly, if using a ladder use extreme caution. Two
people are recommended for this operation.
• If technical assistance is required, contact Huffy Sports’ Sample and
Display Technician.
• Serious injury could occur if teeth/face come in contact with
backboard, net or rim.
• Display recommended for 3” (7.6 cm) or 3-1/2” (9 cm) Round or 4”
(10 cm) Square poles only.
• All instructions and warnings MUST accompany any display item
that is sold.
Most injuries are caused by misuse and/or not following
instructions.
Use caution when installing this unit.
P/N 21154401
01/04
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST (See Hardware Identifier)
Item Qty.
Part No.
Description
Item Qty.
Part No.
Description
1
2
2
900033
203796
200318
203472
201651
206303
203113
203100
201219
990062
904847
206987
203798
900217
201129
203231
201124
240017
201160
206304
904808
203470
900846
206360
203103
204803
206244
201159
904820
203232
206305
901097
203309
200516
Back Bracket
35
2
1
2
2
6*
4
2
10
1
3
1
1
1
1
1
1
2
2
1
2
1
4
1
4
6
1
1
3
2
1
4
1
2
203795
201125
900103
200874
205528
201642
206219
206340
202814
203038
204855
204856
904833
204872
204832
900060
204857
204858
900253
204859
204850
204290
204853
900235
201683
203084
902319
201344
203231
203493
201611
207103
201682
Nut, Slam Jam
2
T-Bolt, 3/8-16 x 5
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
Spring, Rathet return
Bracket, Backboard Support
Spacer, Steel .402 I.D.x.50 O.D.x1.5 Long
Bolt, Hex Flange, 5/16-18 x 1 Long
Spacer .530 I.D. x.63 O.D. x .875 Long
Pole Cap
3
2
Bracket
4
2
Spring
5
2
Spacer, .50 I.D. x .25 Long
Washer, 1/4" Flat
6
2
7
8*
21
48
1
Bolt, Hex-Flange 5/16-18 x 2.5
Nut, Hex-Flange 5/16-18 whiz Lock
Clip, Smart Clips
8
Lock Nut, Hex Head, 1/2-13
Cap, Pole Top
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Pole, 3-1/2"
Bolt, Carriage 5/16-18 X 2-3/4
Handle, Left
1
Pole, Display, 3" O.D. x 43" Long
Wedge
3
Handle, Right
2
Bolt, Hex 5/16-18 x 1.5" Long
Pole, Display
Height Adjustment Rod
Label, Height Indicator
Bracket, Pole Mount
Pole, Display
1
2
Spacer, 1-3/4" Long
Bolt, Carriage, 5/16-18 x 3.5" Long
Lock Nut, Hex Head, 3/8-16
Bolt, Hex Head 1/4-20 x 2 1/4
Pawl Lever
2
5
Spacer, Metal 1/2” O.D.x1.44 Long
Spacer, Biscuit, Plastic
Backboard Mounting Bracket
Cover, Pin Slide
1
1
5
Bolt, Hex Head 1/2-13 x 6 5/16
Elevator Tube, Black
Washer, Flat, Slam Jam
Board Bracket, Black
Bolt, Hex Head 3/8-16 x 2 5/8
Carriage Bolt
6
Pin, Locking
2
Net
2
Lanyard, Black
5
Rim
2
Spacer,1.5" Long
1
Screw Phillips Head
Bolt, Hex Head 1/2-13 x 8" Long
Ratchet
Bolt, Carriage, 5/16-18 x 1.75"
Rim Bracket
5
1
Plastic Knob
2
Elevator Tube, Black, Long
Washer, Flat
Bolt, Carriage, 5/16-18 x 3.5" Long
Lockut,Hex,1/4-20
4
1
PIN,CLEVIS
Nut, Hex-Flange 5/16 x 3" Long
Pole Cap, 3-1/2"
1
Extension Arm
12
4
Washer 1” O.D.
Spacer, Plastic, 1.88" Long
Cover, Bolt End
HARDWARE IDENTIFIER (NUTS & SCREWS)
Item #17 (5)
Item #64 (1)
Item #8 (21)
Item #42 (10)
Item #35 (2)
Item #26 (1)
HARDWARE IDENTIFIER (STEEL SPACERS)
Item #38 (2)
Item #15 (2)
P/N 21154401
01/04
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (BOLTS & SCREWS)
Item #18 (1)
Item #16 (2)
Item #39 (6)*
Item #25 (2)
Item #24 (5)
Item #20 (5)
Item #7 (10)
Item #63 (2)
Item #27 (5)
Item #2 (2)
Item #13 (2)
Item #65 (4)
HARDWARE IDENTIFIER (SPRINGS & WASHERS)
Item #4 (2)
Item #22 (2)
Item #30 (4)
Item #33 (12)
PLASTIC SPACERS
Item #40 (4)
Item #67 (2)
Item #59 (6)
P/N 21154401
01/04
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Install display boards in the marked locations. Each mounting location consists of a mounting pole
stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction
the board is facing).
Display Stand - Top View
3-1/2"
3"
Corner “4”
80602
Corner “3”
61259
Corner “2”
73256
Corner “1”
9H235A
3"
3"
Display boards will be mounted as follows:
Corner Location 1: 9H235A
• 48” SFA Board
• Titanium II Logo
• Black Slam Jam Goal with Cover
• Exacta- Height Elevator System (use existing elevator system)
Corner Location 2: 73256
• 48” Fan Recycled Board
• Viper Logo
• Black Slam Jam Goal
• Ratchet Elevator System
Corner Location 3: 61259
• 44” Fan Recycled Board
• Evolution Logo
• Black Standard Goal
• No Tools, E3 Elevator System
Corner Location 4: 80602
• 44” Fan Recycled Board
• Zone Attack Logo
• Black Standard Goal
• Extension Arm (use existing extension arm assembly)
P/N 21154401
01/04
6
Download from Www.Somanuals.com. All Manuals Search And Download.
At corner locations 1, 2, and 3 install the display pole to the mounting pole stub. If required,
secure the display pole by sliding the display wedge (12) into position as shown. To lock the
display pole in place, tighten the set screw (13 or 39).
1.
39: QTY 1
12: QTY 3
13: QTY 2
At corner location 4 slide the display pole (14) (3 1/2” diameter) over the mounting pole stubs.
2.
10
P/N 21154401
01/04
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ELEVATOR ASSEMBLY - Corner Location 1
Attach spacers (51, 52) to pole mount
Install pole mount bracket (49) with carriage
1.
2.
bracket (49) with bolts (24), washers (30),
and nuts (17) as shown. IMPORTANT!
Tighten until washers (30) no longer
move.
bolts (16) as shown.
Tighten flange nuts (8) completely.
16
30
17
49
11
52
30
49
24
8
51
Apply logo and height indicator labels (48) to
adjustment rod (47) as shown.
3.
Attach covers (54) onto pole mount bracket
(49) with carriage bolt (44) and nut (8) as
shown. IMPORTANT! Loop end of pin
lanyard (57) over carriage bolt (44) during
this assembly. NOTE: Assemble lanyard
(57) to locking pin (55) as shown.
4.
Attach handle parts (45, 46) to adjustment
rod (47) with screw (26), carriage bolts (25),
and flange nuts (8) as shown. NOTE: Holes
in adjustment rod allow for either rear access
or side access.
54
54
49
44
8
47
57
48
55
45
57
46
26
8
25
55
P/N 21154401
01/04
8
Download from Www.Somanuals.com. All Manuals Search And Download.
STEEL FRAME ACRYLIC BACKBOARD ASSEMBLY - Corner Location 1
Attach backboard support brackets (37) to the
backboard frame using bolts (24), spacers (38),
5.
38
and nuts (17) as shown.
17
38
17
37
24
24
Attach lower elevator tubes (29) to backboard support brackets (37) using spacers (59), bolt (27),
6.
and nut (42) as shown. NOTE: Rim mounting nuts (8) and bolts (39) supplied with rim hardware.
8
8
37
42
59
59
27
29
29
2
Refer To
Instructions
Included With Rim
Hardware For Rim
Assembly.
39
39
P/N 21154401
01/04
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach upper elevator tubes (21) to backboard support brackets (37) using spacers (59), bolt
(27), and nut (42) as shown.
7.
42
59
37
21
59
27
21
8.
Attach backboard assembly to pole section (11). Install pole cap (43).
WARNING!
USE CAUTION; ELEVATOR
ASSEMBLY IS HEAVY.
43
TWO PEOPLE REQUIRED FOR
THIS PROCEDURE. FAILURE TO
FOLLOW THIS WARNING COULD
21
21
RESULT IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
29
42
27
27
11
29
P/N 21154401
01/04
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach adjustment rod (47) to lower elevator
tubes (29) using bolt (27) spacer (59) and nut
(42) as shown.
Insert handle assembly through pole
mount assembly as shown. Lock pole
assembly in place at the 10’ (3.05m)
mark with pin (55).
9.
10.
55
29
29
42
27
67
67
47
P/N 21154401
01/04
11
Download from Www.Somanuals.com. All Manuals Search And Download.
12.
• Fit rim (58) securely into bracket (1) as shown.
• Install reinforcement bracket (3) onto “T” bolt (2) as shown.
• Install spring (4) onto “T” bolt (2) as shown.
• Install special nut (35) and washer (22) onto “T” bolt (2).
58
35
2
22
4
1
3
NOTE:
Tighten nut (35) until
flush with end of "T" bolt
(2) as shown here.
P/N 21154401
01/04
12
Download from Www.Somanuals.com. All Manuals Search And Download.
44” FAN MOLDED PLASTIC BOARD ASSEMBLY - Corner Location 2
Correctly identify each pole section.
1.
ONLY THE TOP POLE SECTION (14) IS USED IN THIS ASSEMBLY.
MIDDLE POLE 43”
TOP POLE 31”
14
BOTTOM POLE 43”
2.
Fit spacer (15) into pawl (19). Then continue to assemble as shown. Tighten completely.
64
23
17
15
15
18
19
24
Identify elevator tubes (21).
3.
21
Toward
Board
Toward
Pole
Elevator tube
P/N 21154401
01/04
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Assemble elevator tubes (21) to ratchet (28) and backboard brackets (23) using bolts (20),
spacers (5, & 40), and nuts (42) as shown. Tighten completely.
4.
19
42
23
40
42
21
5
40
28
20
20
5
IMPORTANT!:
It is necessary for
all parts to be
installed properly
for this mechanism
to work safely and
properly.
LEVER
21
BROOM
HANDLE
Secure pawl (19) in place with clevis
pin (31) and washers (6) as shown.
Hook one end of the spring (36) into hole of
clevis pin (31). Stretch spring (36) and hook
it into the notch of the bracket with pliers.
5.
6.
6
21
19
31
23
6
36
21
WARNING!
USE EYE PROTECTION
WHEN INSTALLING
SPRINGS.
P/N 21154401
01/04
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert “T” bolt (2) through Slam Jam bracket (1) as shown.
7.
Secure Slam Jam bracket (1) and backboard bracket (23) assemblies to backboard. Bend
upper halves of backboard brackets (23) to line up with holes in backboard and secure
with bolts (44 & 7) and nuts (8).
Tighten completely.
8
23
8
21
2
WARNING!
TWO PEOPLE REQUIRED
FOR THIS PROCEDURE.
FAILURE TO FOLLOW THIS
WARNING COULD RESULT
IN SERIOUS INJURY AND/OR
PROPERTY DAMAGE.
2
44
1
7
Attach upper elevator tubes (21) to backboard brackets (23) using spacers (40) bolt (20)
8.
and nut (42) as shown.
21
42
23
40
40
21
20
21
21
P/N 21154401
01/04
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach upper and lower elevator tubes (21) to top pole section (14) using bolts (20) and
9.
nuts (42) as shown. Attach pole cap (41) as shown.
41
21
21
21
20
42
20
21
WARNING!
TWO PEOPLE REQUIRED FOR
THIS PROCEDURE. FAILURE
TO FOLLOW THIS WARNING
COULD RESULT IN SERIOUS
INJURY AND/OR PROPERTY
DAMAGE.
10.
• Fit rim (58) securely into bracket (1) as shown.
• Install reinforcement bracket (3) onto “T” bolt (2) as shown.
• Install spring (4) onto “T” bolt (2) as shown.
• Install special nut (35) and washer (22) onto “T” bolt (2).
58
35
2
NOTE:
Tighten nut (35) until
22
flush with end of "T" bolt
(2) as shown here.
4
1
3
P/N 21154401
01/04
16
Download from Www.Somanuals.com. All Manuals Search And Download.
FAN MOLDED PLASTIC BOARD ASSEMBLY - Corner Location 3.
Correctly identify each pole section.
Pole bracket will need to be lightly pressed into
2.
1.
Poles have an identification sticker
backboard ribbing. Be sure to press completely into
that will be used as a reference point
place. Attach rim(58) to backboard and pole bracket
in the next step.
(53) with knob (62), reinforcement bracket (61), and
ONLY THE TOP POLE SECTION
(50) IS USED IN THIS ASSEMBLY.
carriage bolt (60) as shown. Tighten knob
completely.
WARNING!
KNOB MUST BE TIGHTENED
COMPLETELY AND CHECKED
FOR TIGHTNESS BEFORE
EACH USE.
62
TOP
50
61
MIDDLE
58
NOTE:
BOTTOM
60
BOARD STYLE
MAY VARY
53
PRESS BRACKET (20)
INTO PLACE HERE
3.
Attach board assembly to pole with carriage
bolts (63) and knobs (62) as shown. Install pole
cap (41) as shown.
41
62
63
50
P/N 21154401
01/04
17
Download from Www.Somanuals.com. All Manuals Search And Download.
FAN BACKBOARD ASSEMBLY - Corner Location 4.
Assemble fan backboard as shown below with a standard rim as shown.
1.
65
WARNING
TWO PERSON MINIMUM
REQUIRED FOR THIS
PROCEDURE.
33
NOT FOLLOWING
RECOMMENDATION MAY
RESULT IN BODILY INJURY.
32
33
8
66
7
8
34
33
10
P/N 21154401
01/04
18
Download from Www.Somanuals.com. All Manuals Search And Download.
11.
Install net clips.
CLIP “ARM”
WARNING!
USE OF THIS PRODUCT
WITHOUT PROPER
INSTALLATION OF SMART
CLIPS®, OR WHEN ALL SMART
CLIPS® ARE NOT PRESENT
COULD RESULT IN BODILY
HARM. BE SURE TO FOLLOW
DIRECTIONS CAREFULLY.
CLIP “BODY”
58
Insert one “arm” of clip into ram as shown. Twist “body” of clip
slightly so that second “arm” slides over the top of the first “arm” as
shown.
Push in direction indicated by arrows.
A
9
Push second “arm” back and into ram as shown.
B
Twist “body” of clip slightly again to spread “arms” of clip.
Clip “arms” must be flat and touching edge to edge as shown, not
overlapping.
C
P/N 21154401
01/04
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Install net.
12.
58
SIDE VIEW
56
9
NETCLIP
NET
Insert net into bottom of clip as shown.
SIDE VIEW
Twist net until it snaps into position.
Net must be centered through clip.
NETCLIP
NET
P/N 21154401
01/04
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|