Pro Image Rim
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
WARNING!
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
TOOLS AND MATERIALS
REQUIRED
FOR ASSEMBLY:
• Two People
• Step Ladder, 8 ft. (2.4 m)
FAILURE TO FOLLOW
• Wrenches (One) 3/4", (Two) 9/16” and
(Two) 1/2” or (Two) Adjustable Wrenches
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO PROPERTY.
Toll-Free Customer Service Number for U.S: 1-888-713-5488,
For Canada: 1-800-284-8339,
For Europe: 00 800 555 85234 (Sweden: 009 555 85234),
For Australia: 1-800-333 061
Internet Address: http://www.huffysports.com
1
11/03
P/N 211644
© COPYRIGHT 2000 by HUFFY SPORTS
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE TO ASSEMBLERS
ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled
and ballasted with sand or water according to the instructions. Failure to follow instructions
could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
IMPORTANT!
Remove all contents from boxes.
Be sure to check inside pole sections;
hardware and additional parts are packed inside.
WARRANTY CARD:
Please remember to complete your product
registration form either on-line at:
www.huffysports.com or mail-in the
enclosed postcard.
For more information on assembly, placement, proper
use, and maintenance, visit The American Basketball
3
11/03
P/N 211644
Download from Www.Somanuals.com. All Manuals Search And Download.
Get to know the basic parts of your basketball system.....
RIM
BACK
BRACKET
RIM
BACK
SPRINGS
BRACKET
PARTS LIST - See Hardware Identifier
Item Qty. Part No. Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
1
2
2
2
2
8
2
2
2
2
2
2
1
1
1
4
4
1
1
2
2
2
1
Rim
202604 Bolt, Carriage 3/8 x 4.75” Long
203474 Washer, Flat, 1”O.D.
203017 Hex Nut, 3/8”
203063 Nylon Lock-Nut, 3/8”
203232 Washer, 3/4” O.D.
200484 Spring, Zinc
202601 Washer, Flat
202602 Lock Washer
202523 Spacer
203439 Bolt, Hex, 3/8 x 6” Long
220140 Screw, Self-Tapping
908087 Back Bracket - Red
108085 Inner Bracket - Zinc
918086 Cover Plate - Red
201611 Bolt, Hex, 5/16-18 x 3" Long
203100 Whiz Nut, 5/16”
204290 Net
202655 Label, Logo
202636 Special Nut, Locking
203795 Special Nut
202603 Nylon Washer
202531 Tension and Leveling Label
4
P/N 211644
11/03
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (BOLTS & SCREWS)
Item #2 (2)
Item #12 (2)
Item #16 (4)
Item #11 (2)
HARDWARE IDENTIFIER (NUTS & WASHERS)
Item #5 (2)
Item #4 (2)
Item #21 (2)
Item #8 (2)
Item #3 (2)
Item #20 (2)
Item #6 (8)
Item #9 (2)
Item #17 (4)
HARDWARE IDENTIFIER (METAL SPACERS & NYLON WASHERS)
Item #10 (2)
Item #22 (2)
5
11/03
P/N 211644
Download from Www.Somanuals.com. All Manuals Search And Download.
Install two carriage bolts (2) through rim (1), washers (3), and lock washers (9) as shown.
Tighten nuts (4) completely.
1.
NOTE:
Perform this step twice
as it is applied to both
holes of rim bracket
shown
2
1
NOTE: COMPLETED ASSEMBLY:
3
9
4
Place a special locking nut (20) approximately half-way up on each carriage bolt (2) as
shown. Keep the two special locking nuts (20) at the same level.
2.
2
NOTE: COMPLETED ASSEMBLY:
20
6
P/N 211644
11/03
Download from Www.Somanuals.com. All Manuals Search And Download.
First, test fit spacer (10) into back bracket
(13) and Carefully rock in a circular motion to
ream out any excess paint from holes if
necessary.
3a.
3b.
13
10
Place rim (1) into back
bracket (13) so that the holes
are properly aligned.
1
13
Line up holes
20
3c.
Then, insert spacer (10) through back bracket (13), nylon washers (22) and rim assembly (1).
BOTTOM VIEW
NOTE:
Ends of spacer (10) should
be flush on both sides of
board bracket (13).
22
10
BOTTOM VIEW
22
1
13
22
22
10
Spacer
flush with
bracket
Spacer
flush with
bracket
13
7
11/03
P/N 211644
Download from Www.Somanuals.com. All Manuals Search And Download.
Install bolt (11) through top holes on bracket (13) using washers (6) and nut (5) as
shown. Tighten completely.
10
4.
6
6
22
5
22
11
Attach rim assembly to backboard and support structure by inserting bolts (16) through
bottom holes in back bracket (13). Secure with nuts (17) and washers (6). Tighten nuts
(17) completely.
5.
16
17
6
13
17
16
6
8
P/N 211644
11/03
Download from Www.Somanuals.com. All Manuals Search And Download.
Position rim assembly (1) 90 degrees to back bracket (13) as shown. Place inner-bracket
(14) over both carriage bolts (2) followed by springs (7), washers (8) and special nuts (21).
6.
NOTE:
COMPLETED
ASSEMBLY:
NOTE:
Tighten special nuts (21)
until flush with end of
carriage bolts (2)
as shown.
NOTE:
Do not over tighten as rim
will not flex properly. See
leveling instructions (Step
11) to determine how much
to tighten nuts (20) and (21).
1
13
8
14
7
21
2
20
Lower lower rim down. Holes in inner bracket (14) should line up with holes in
backboard bracket (13). If not, adjust special locknuts (20 & 22) until holes are aligned.
7.
13
20
Align these
holes.
22
13
9
11/03
P/N 211644
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure back bracket (13) fully to backboard by inserting bolts (16) through upper
holes in back bracket (13), Add washers (6) and nuts (17) to bolts (16).
Tighten nuts (17) completely.
8.
17
16
6
First, test fit spacer (10) into back bracket (13) and Carefully rock in a circular motion
to ream out any excess paint from holes if necessary. Insert spacer (10) through
bottom holes in board bracket (13) and inner bracket (14).
9.
13
10
BOTTOM VIEW
NOTE:
Ends of spacer (10) should be
flush on both sides of board
bracket (13).
13
Spacer
flush with
bracket
Spacer
flush with
bracket
10
10
P/N 211644
11/03
Download from Www.Somanuals.com. All Manuals Search And Download.
Then, install bolt (11), washers (6), and nut (5) through spacer (10)
and tighten completely.
10.
6
5
6
11
LEVELING AND TENSION
ADJUSTING INSTRUCTIONS:
11.
Adhere leveling and tension adjusting label
(23) to inside of rim cover plate (15).
23
TO LEVEL RIM,
TIGHTEN OR LOOSEN THESE NUTS
TO ADJUST RIM TENSION ,
TIGHTEN OR LOOSEN THESE NUTS
20
21
202531
Place level on rim (1) and adjust nut (20) until
level. Tighten nut (21) to set rim tension for
playing.
15
11
11/03
P/N 211644
Download from Www.Somanuals.com. All Manuals Search And Download.
Apply logo label (19) to cover plate (15). Install cover plate (15) on rim (1) using
self tapping screws (12) as shown (note orientation of cover plate).
12.
NOTE:
Cover plate (15)
will fit over back
bracket.
19
15
12
15
15
15
13.
Secure net (18) to rim (1).
1
1
2
NOTE: Official rim height
is 10-0’ (3.05 m) from top
of rim to playing surface.
OUTSIDE VIEW
4
3
10 feet
(3.05 m)
12
P/N 211644
11/03
Download from Www.Somanuals.com. All Manuals Search And Download.
|