Customer Service
N53 W24700 South Corporate Circle
Sussex, WI 53089
U.S.A.
A Huffy Company
Model 89025
Please refer to modular category #350 when arranging product for modular display.
SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY
RESULT IN SERIOUS INJURY,
PROPERTY DAMAGE AND WILL VOID WARRANTY.
This unit is intended for display purposes only and
should not be used for play.
To ensure safety, do not attempt to assemble this system without
following the instructions carefully. Check entire box and inside all
packing material for parts. Before beginning assembly, read the
instructions and identify parts in this document. Proper and
complete assembly, use and supervision is essential for proper
operation and to reduce the risk of accident or injury. A high
probability of serious injury exists if this system is not installed,
maintained, and operated properly.
•
•
•
•
•
During assembly, if using a ladder use extreme caution. Two
people are recommended for this operation.
If technical assistance is required, contact Huffy Sports’ Sample
and Display Technician.
Serious injury could occur if teeth/face come in contact with
backboard, net or rim.
Display recommended for 3” (7.6 cm) or 3-1/2” (9 cm) Round or 4”
(10 cm) Square poles only.
All instructions and warnings MUST accompany any display item
REQUIRED TOOLS AND
MATERIALS:
that is sold.
• 2 People
• Wrenches: (Two each) 7/16”, 1/2”, 9/16”, and 3/4”
or Pliers
Most injuries are caused by misuse and/or not following
instructions.
Use caution when installing this unit.
• Phillips Screwdriver
• 2 Step Ladders, 8 ft. (2.4 m)
IMPORTANT!
We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection. Although
great care and effort have been taken, problems may occur. To ensure prompt and correct handling of any problems, or to answer any
questions, please contact the Sample and Display Technician at 414-820-3440.
1
06/03
P/N 211543B
Download from Www.Somanuals.com. All Manuals Search And Download.
RIM ASSEMBLY - Corner Locations 1 and 2
Assemble rims as shown below.
1
3.
4.
2
3
4
5.
7
8
3
06/03
P/N 211543B
Download from Www.Somanuals.com. All Manuals Search And Download.
Install net clips.
WARNING: Use of this product without proper installation of net
clips, or when all net clips are not present could result in bodily harm. Be
sure to follow directions carefully.
6.
CLIP “ARM”
CLIP “BODY”
58
Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second
“arm” slides over the top of the first “arm” as shown.
Push in direction indicated by arrows.
9
A
Push second “arm” back and into ram as shown.
B
Twist “body” of clip slightly again to spread “arms” of clip.
Clip “arms” must be flat and touching edge to edge as shown, not overlapping.
C
4
P/N 211543B
06/03
Download from Www.Somanuals.com. All Manuals Search And Download.
NET INSTALLATION
58
7.
SIDE VIEW
9
NETCLIP
10
NET
Insert net into bottom of clip as shown.
SIDE VIEW
Twist net until it snaps into position.
Net must be centered through clip.
NETCLIP
NET
5
06/03
P/N 211543B
Download from Www.Somanuals.com. All Manuals Search And Download.
8.
At corner locations 1, 2, and 3 install the display pole (11) to the mounting pole stub. If required, secure the
display pole (11), slide the display wedge (12) into position as shown. Tighten the set screw (13) to lock the
display pole (11) in place. Use the second wedge only if necessary to tighten the fit.
11
12
13
At corner location 4 slide the display pole (14) (3 1/2” diameter) over the mounting pole stubs.
9.
14
6
P/N 211543B
06/03
Download from Www.Somanuals.com. All Manuals Search And Download.
ELEVATOR ASSEMBLY - Corner Locations 1 and 3
Attach spacers (51, 52) to pole mount bracket
Install pole mount bracket (49) with
10.
11.
(49) with bolts (24), washers (30), and nuts (17)
as shown. IMPORTANT! Tighten until
washers (30) no longer move.
carriage bolts (16) as shown.
Tighten flange nuts (8) completely.
16
30
17
49
11
52
30
49
24
8
51
Apply logo and height indicator labels (48) to
adjustment rod (47) as shown.
13.
12.
Attach covers (54) onto pole mount bracket (49)
with carriage bolt (31) and nut (8) as shown.
IMPORTANT! Loop end of pin lanyard (57)
over carriage bolt (31) during this assembly.
NOTE: Assemble lanyard (57) to locking pin (55)
as shown.
Attach handle parts (45, 46) to adjustment rod (47)
with screw (26), carriage bolts (22), and flange
nuts (8) as shown. NOTE: Holes in adjustment rod
allow for either rear access or side access.
54
54
49
44
47
8
48
57
55
45
46
26
8
25
57
55
7
06/03
P/N 211543B
Download from Www.Somanuals.com. All Manuals Search And Download.
44” STEEL FRAME ACRYLIC BACKBOARD ASSEMBLY - Corner Location 1
Attach backboard support brackets (37) to the
backboard frame using bolts (24), spacers (38),
14.
38
and nuts (17) as shown.
17
38
17
37
24
24
Attach lower elevator tubes (29) to backboard support brackets (37) using spacers
(59), bolt (20), and nut (42) as shown. NOTE: Rim mounting nuts (8) and bolts
(39) supplied with rim hardware.
15.
8
8
37
42
59
59
27
29
29
Refer To
Instructions
Included With Rim
Hardware For Rim
Assembly.
39
39
8
P/N 211543B
06/03
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach upper elevator tubes (21) to backboard support
brackets (37) using spacers (59), bolt (27), and nut (42)
as shown.
16.
42
59
37
21
59
27
21
Attach backboard assembly to pole section (11). Install
pole cap (43). NOTE: Two people are recommended for
this step. Use caution; elevator assembly is
heavy.
17.
42
21
29
43
11
21
29
27
27
9
06/03
P/N 211543B
Download from Www.Somanuals.com. All Manuals Search And Download.
18. Insert handle assembly through pole mount
assembly as shown. Lock pole assembly in place at
the 10’ (3.05m) mark with pin (55).
Attach adjustment rod (47) to lower elevator
tubes (29) using bolt (27) spacer (59) and
nut (42) as shown.
19.
55
42
59
47
29
59
27
29
44” FAN MOLDED PLASTIC BOARD ASSEMBLY - Corner Location 3
20.
Assemble backboard brackets (23) using spacers (15) bolts (18, 24) and nuts (19, 17) as
shown.
23
23
65
17
15
18
15
24
10
P/N 211543B
06/03
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach lower elevator tubes (29) to backboard brackets (23) using spacers (59) bolt (27) and nut (42)
as shown.
21.
23
42
59
29
59
27
29
Bend top of backboard brackets (23) outward to match up with holes on backboard and secure
using nuts (8) and bolts as shown. Attach rim to backboard using using bolts and nuts (8) as
shown.
22.
23
8
8
29
REFER TO
INSTRUCTIONS
INCLUDED WITH RIM
HARDWARE FOR
RIM ASSEMBLY
11
06/03
P/N 211543B
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach upper elevator tubes (21) to backboard brackets (23) using spacers (22) bolt (27) and nut (42)
as shown.
23.
42
21
22
22
27
21
Attach backboard assembly to pole section (11).
42
42
24.
Then install pole cap (43). NOTE: Two people
are recommended for this step. Use caution;
elevator assembly is heavy.
21
29
43
21
27
27
12
P/N 211543B
06/03
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert handle assembly through pole mount
assembly as shown. Lock pole assembly in
place at the 10’ (3.05m) mark with pin (55).
25.
Attach adjustment rod (47) to lower
elevator tubes (27) using bolt (27) spacer
(59) and nut (42) as shown.
26.
55
42
47
59
29
59
27
29
HEIGHT ADJUSTMENT
27.
To Set Backboard Height:
A. While holding handle, remove pin (55).
B. Move elevator up or down to desired height.
C. Replace pin full length to lock system at desired
height.
A
C
55
B
13
06/03
P/N 211543B
Download from Www.Somanuals.com. All Manuals Search And Download.
44” FAN MOLDED PLASTIC BOARD ELEVATOR ASSEMBLY - Corner Location 2
1.
Attach elevator bracket (36)
and reinforcement bracket (41)
to pole section (11) using bolts
(16) and nuts (8) as shown.
11
41
16
36
8
Assemble backboard brackets (23) using spacers (15) bolts (18, 24) and nuts (19, 17) as
shown.
2.
23
23
65
17
15
18
15
24
14
P/N 211543B
06/03
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach lower elevator tubes (29) to backboard brackets (23) using spacers (60) bolt (27) and nut (42) as
shown.
3.
23
42
60
29
60
27
29
4.
Bend top of backboard brackets (23) outward to match up with holes on backboard and secure using
nuts (8) and bolts as shown. Attach rim to backboard using using bolts and nuts (8) as shown.
8
23
8
8
29
REFER TO
INSTRUCTIONS
INCLUDED WITH RIM
HARDWARE FOR
RIM ASSEMBLY
DO NOT USE
WASHERS HERE ON
SPRING RETURN
STYLE RIMS
58
15
06/03
P/N 211543B
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach upper elevator tubes (21) to backboard brackets (23) using spacers (56) bolt (20) and nut (42)
as shown.
5.
42
21
56
56
20
21
42
42
Attach backboard assembly to top pole section
(11). Then install pole cap (43). NOTE: Two
people are recommended for this step. Use
caution; elevator assembly is heavy.
6.
21
29
43
21
27
20
16
P/N 211543B
06/03
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
Fig. A
Insert locking pin (28) into bracket on adjustment
tube (6). Insert cross pin (5) through hole in bracket
and locking pin (28) as shown in figure A. Fit left
handle (31) onto adjustment tube (6) so the bottom of
adjustment tube (6) sits on the two small ribs of the
handle as shown in figure B.
5
6
5
28
6
31
Fig. B
6
31
17
06/03
P/N 211543B
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert spring (53) into back of locking pin (28) as shown. Spring (53) should rest between two
small ribs at the back of the plastic handle as shown in Figure C. Insert top of trigger (50) into
bracket on the adjustment tube (6) as shown. The plastic post of the handle pieces should go
through the hole in bottom of trigger (50) and hold it into place as shown.
8.
28
6
53
50
Fig. C
28
53
31
31
18
P/N 211543B
06/03
Download from Www.Somanuals.com. All Manuals Search And Download.
Finish handle assembly by
attaching right handle using screws
as shown.
Attach adjustment tube to lower elevator tubes
using bolt spacers and nut as shown.
10.
9.
61
61
27
6
59
29
61
61
59
61
42
19
Insert lower adjustment rod (62) into bottom of adjustment tube (6), pull trigger to allow lower adjustment
rod to move about mid-way into adjustment tube (6), release the trigger so the lower adjustment rod (62)
locks into position midway inside the adjustment tube (6). Attach the lower adjustment rod (62) to
elevator bracket (65) using bolt (63) and nut (64) as shown.
11.
WARNING
TWO PERSON MINIMUM
REQUIRED FOR THIS
PROCEDURE.
NOT FOLLOWING
RECOMMENDATION MAY
RESULT IN BODILY INJURY.
6
62
36
63
62
64
19
06/03
P/N 211543B
Download from Www.Somanuals.com. All Manuals Search And Download.
40” FAN BACKBOARD ASSEMBLY - Corner Location 4.
Assemble 40” fan backboard as shown below with a standard rim as shown.
12.
7
WARNING
TWO PERSON MINIMUM
REQUIRED FOR THIS
PROCEDURE.
33
NOT FOLLOWING
RECOMMENDATION MAY
RESULT IN BODILY INJURY.
32
35
8
7
8
34
35
20
P/N 211543B
06/03
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST - See Hardware Identifier
Item Qty.
Part No.
Description
Item Qty.
Part No.
Description
1
2
2
900033
203796
200318
203472
200215
900006
203113
203100
201219
204290
904847
206987
203156
908407
201129
203053
201124
240017
200210
206304
908002
206311
900846
206360
203103
204803
201640
200214
904821
203232
200211
201097
203309
200516
Back Bracket
35
6
1
2
2
4*
2
1
15
3
1
2
2
2
2
2
1
4
4
1
4
2
4
2
4
8
2
5
2
1
2
2
203218
200209
900103
200874
205528
201642
206990
206340
207103
203038
204855
204856
904866
204872
204832
200212
204857
204858
200257
204859
204850
201642
204853
Washer 5/16 Flat
2
T-Bolt, 3/8-16 x 5
Bracket
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
Pole Mount Bracket
3
2
Bracket, Backboard Support
Spacer, Steel .402 I.D.x.50 O.D.x1.5 Long
Bolt, Hex Flange, 5/16-18 x 1 Long
Spacer .530 I.D. x.63 O.D. x .875 Long
Reinforcement Bracket
Lock Nut, Hex Head, 1/2-13
Cap, Pole Top
4
2
Spring
5
1
Cross Pin
6
1
Adjustment Tube - Upper
Bolt, Hex-Flange 5/16-18 x 2.5
Nut, Hex-Flange 5/16-18 whiz Lock
Clip, Smart Clips
Net
7
16*
34
48
4
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
Bolt, Carriage 5/16-18 X 2-3/4
Handle, Left
3
Pole, Display
2
Wedge
Handle, Right
2
Bolt, Hex 5/16-18 x 1
Pole, Display
Height Adjustment Rod
Label, Height Indicator
Bracket, Pole Mount
Trigger
1
4
Spacer, 1 3/4
4
Bolt, Carriage, 5/16-18 x 4 Long
Lock Nut, Hex Head, 3/8-16
Bolt, Hex Head 1/4-20 x 2 1/4
Right Handle
8
Spacer, Metal 1/2” O.D.x1.44 Long
Spacer, Biscuit, Plastic
Compression Spring
Cover, Pin Slide
2
1
2
Bolt, Hex Head 1/2-13 x 6 5/16
Elevator Tube, Black
Spacer, Plastic
4
Pin, Locking
4
Spacer, .530 x .625 Long
Lanyard, Black
4
Board Bracket, Black
Bolt, Hex Head 3/8-16 x 2 5/8
Carriage Bolt
2
Rim
4
202862
201681
204804
908008
202739
203220
203493
Spacer,1.190 Long
2
Screw Phillips Head
Bolt, Hex Head 1/2-13 x 7-1/4
Locking Pin
Spacer, .88 Long
13
1
Screw, Phillips Head, 3/4 Long
Adjustment Rod - Lower
Bolt 5/16-18 x 1.75 Long
Nylon Insert Lock Nut, 5/16-18
Lockut,Hex,1/4-20
6
Elevator Tube, Black, Long
Washer, Flat
8
1
Left Handle
1
Extension Arm
24
4
Washer 1” O.D.
* You May Have Extra Parts With This Model.
Cover, Bolt End
HARDWARE IDENTIFIER (NUTS & SCREWS)
Item #17 (8)
Item #65 (2)
Item #8 (34)
Item #42 (15)
Item #6 (2)
Item #26 (2)
Item #61 (5)
HARDWARE IDENTIFIER (STEEL SPACERS)
Item #38 (2)
Item #15 (4)
21
06/03
P/N 211543B
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE IDENTIFIER (BOLTS & SCREWS)
Item #18 (2)
Item #16 (4)
Item #24 (2)
Item #39 (4)*
Item #25 (4)
Item #20 (2)
Item #7 (16)
Item #27 (13)
Item #63 (1)
Item #2 (2)
HARDWARE IDENTIFIER (SPRINGS & WASHERS)
Item #30 (8)
Item #4 (2)
Item #33 (24)
PLASTIC SPACERS
Item #35 (6)
Item #22 (4)
Item #60 (2)
Item #40 (2)
Item #59 (8)
22
P/N 211543B
06/03
22 of 22
Download from Www.Somanuals.com. All Manuals Search And Download.
|