Hotpoint Washer WF620 User Manual

INSTRUCTIONS FOR INSTALLATION & USE for the AQUARIUS+ RANGE  
WF645,WF640,WF630 and WF620  
Hotpoint recommends, for your own safety and to ensure you get the best possible results from your  
Washing Machine, you read through this booklet and follow these steps thoroughly.  
Electrical Guide  
Installation Guide  
STEP 1  
STEP 2  
STEP 4  
STEP 6  
STEP 8  
Dispose of packaging material in a safe  
place and remove any labels.  
Choose a location for your washing  
machine, where possible on a solid floor,  
with the electrical sockets and water  
supply taps easily accessible.  
Allow sufficient space: 600mm width,  
600m depth and 900mm height.  
DO NOT install in a bath or shower room.  
Please read instructions thoroughly to  
ensure you understand each stage  
before you begin.  
Remember you may be charged for a service call if a  
problem with your washing machine is caused by  
incorrect installation or misuse.  
WARNING: This appliance must be earthed.  
Dispenser Drawer  
Programme Selection  
STEP 3  
Read through this section to familiarise  
yourself with the different  
compartments within the dispenser  
drawer.  
A wash chart is provided to help you to  
select your required programme.  
Examples are given for the maximum  
washing load weights for different fabric  
types.  
NOTE: Always follow manufacturer’s dosage  
recommendations.  
Using your Machine  
Options Guide  
STEP 5  
How to start your selected programme  
and how to stop or change the  
programme if so required.  
All available optional wash features are  
explained within this section - These  
allow you to adjust your selected wash  
programme to suit your needs.  
NOTE: In addition to the temperature of the  
incoming water, the selection of optional wash  
features will affect the programme times.  
NOTE: Progress indicator lights show what stage in  
the programme cycle has been reached.  
A Typical Wash Programme  
Troubleshooting  
STEP 7  
Please refer to the Troubleshooting  
section if you have any problems when  
using your washing machine.  
A picture guide provides a clear  
explanation how to set a wash  
programme.  
READ BEFORE  
CONTACTING  
SERVICE!  
There may be nothing wrong!  
DO NOT overload the washing machine.  
NOTE: Hotpoint recommend, on completion of  
your programme, that you switch off both the  
electricity and water supply to the appliance.  
Read the rest of these instructions to get the best from your appliance, remember to fill in your guarantee registration.  
Keep this Book in a safe place for quick reference.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
STEP 2  
1
2
TECHNICAL DETAILS  
CONNECT TO THE WATER  
SUPPLY...  
REMOVE TWO TRANSIT FIXINGS...  
Follow these instructions to remove the TWO transit fixings.  
IMPORTANT:  
It is important the transit  
bolt and spacer come out  
intact (see pic).  
WF645,WF640,  
WF630,  
and WF620  
PLEASE USE THE NEW HOSES SUPPLIED, FITTED  
TO THE MACHINE.  
Situated, one either  
side of the rear panel,  
both transit bolts  
(complete with  
Models  
Old hoses may  
cause leaks due to  
worn out washers  
or may split due to  
spacers) MUST be  
removed before use...  
Failure to do so may  
cause damage to  
your machine!  
59.5cm wide  
Dimensions  
Capacity  
85cm high  
60cm deep  
Use a crosshead  
screwdriver to  
remove the  
For safety, replace both  
plastic covers over the  
holes left by removing  
the two bolts.  
Unscrew the  
STOP when 3  
threads can be  
seen.  
Hold, slide  
across and pull  
to remove.  
water pressure.  
DO NOT REMOVE!  
bolt using a  
13mm spanner.  
plastic cover.  
Connect fill hoses to the  
water supply taps:  
Red or Grey Hose end to  
Hot and Blue Hose end  
to Cold.  
Check both hot  
and cold water  
supplies are  
ii  
i
from 1 to 6kg  
running freely...  
Electric  
voltage 220/230 Volts 50Hz  
3
Connections  
maximum absorbed power 1700W  
DRAINAGE SYSTEM... we recommend one of the following:  
TURN BOTH TAPS ON...  
Check the hoses  
at least once a  
year. Replace any  
that show signs of  
cracking, they  
Water pressure at the tap  
must be in the range...  
Max. 1Mpa (10 bar) and  
Min. 0.05Mpa (0.5 bar)  
Spin Speed  
STANDPIPE METHOD  
up to 1400rpm - WF645 & WF640  
up to 1300rpm - WF630  
up to 1200rpm - WF620  
UNDER SINK METHOD  
iv  
iii  
NOTE: ALTHOUGH YOU MAY NEED TO  
MOVE THE HOOKED END SUPPORT  
ALONG THE GREY DRAINAGE HOSE,  
DO NOT REMOVE IT.  
Hooked End Support  
Insert drainage hose  
approximately 100mm  
into the standpipe.  
.............................  
Control  
might burst due  
to water pressure.  
programmes  
according to  
IEC456  
programme D  
temperature 60˚C  
run with a 6kg load  
OR  
800mm  
WHICHEVER DRAINAGE METHOD  
YOU USE, MAKE SURE THAT THE  
HOOKED END SUPPORT IS FIXED  
LEVEL TO, OR ABOVE THE ‘PLUMBING  
INDICATOR LINE’*  
from floor  
If you have no hot water supply...  
A cold fill adaptor is available from  
your local Hotpoint authorised  
Service Centre or by calling the  
Genuine Parts & Accessories Hotline  
(see KEY CONTACTS).  
Standpipe height:  
minimum 500mm  
from the floor.  
directive  
Fix the hooked Attach the GREY  
end support at drainage hose to the  
a minimum  
800mm from  
the floor.  
cut off the blocked  
end of the under sink  
drainage unit.  
under sink drainage  
unit securely, using a  
hose clip.  
(*see Getting to Know your Appliance)  
4
5
6
LEVEL?...  
CONNECT TO THE POWER SUPPLY...  
READY...  
YOUR MACHINE WILL BE NOISY IF THE TWO FRONT FEET ARE NOT  
ADJUSTED SO THE MACHINE STANDS FIRM AND LEVEL.  
The inclination of the machine, measured on the top, must not exceed 2˚.  
PLUG YOUR MACHINE INTO AN ELECTRICAL SOCKET WHICH IS  
EASILY ACCESSIBLE. SWITCH ON  
TO CHECK ALL PARTS OF THE INSTALLATION AND TO THOROUGHLY  
CLEAN THE INSIDE OF YOUR MACHINE:  
RUN PROGRAMME ‘B’ (refer to ‘Programme Selection, STEP 4).  
-
Move your machine into final location.  
Take care not to trap or kink the hoses.  
Turn one or both front feet clockwise until  
the machine stands firm and level.  
The spring on each foot will stop them  
coming loose.  
NOTE: Hotpoint recommend extension  
leads are not used.  
WITHOUT ANY LAUNDRY  
-
and  
WITHOUT ANY DETERGENT  
If it is placed on a fitted carpet, adjust the feet  
to ensure that there is adequate ventilation  
beneath the washing machine.  
NOTE: The mains cable must only be  
replaced by an authorised serviceman.  
THIS WILL TAKE APPROXIMATELY 2hours 20minutes TO COMPLETE  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Dispenser Drawer  
STEP 3  
1
WARNING:  
Do not put any items into  
2
3
the drawer, other than  
detergents designed to be  
released from the drawer, as  
they may cause damage or  
blockage.  
4
5
Index:  
1. Drawer release latch  
2. Pre-wash detergent compartment  
Maximum 200ml powder or  
100ml liquid  
3. Main detergent compartment  
Maximum 400ml powder or  
200ml liquid  
4. Grate  
5. Fabric conditioner compartment  
120ml maximum  
Dispensing Powder Detergent  
To achieve the best wash results the manufacturer’s  
recommended amount of detergent should be measured  
and added to the main detergent compartment (II symbol)  
(max. 400ml).  
Dispensing Liquid Detergent  
We recommend the use of a detergent dosing ball, as provided by your detergent  
manufacturer.  
Adding Fabric Conditioner  
Pour the recommended amount of fabric conditioner into the  
compartment (flower symbol).  
Do not exceed the maximum fill line.  
Pre-wash Programme A  
When selecting programme A add detergent to both the pre-wash compartment  
(I symbol) and the main wash compartment (II symbol).  
DO NOT use in drum dosing devices with Pre-wash programme A.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programme Selector Dial  
STEP 4  
IMPORTANT INFORMATION: The temperature of the incoming water supply and selection of any Optional Wash Feature, ie. Time Saver,  
will affect the programme times*. Start the programme by following the instuctions in Step 5:On-Off/Selecting a programme...’  
Wash  
label  
Fabric  
Temp.  
˚C  
Max.  
dry  
weight  
load  
Approx.  
programme  
time*  
Spin  
WEIGHT OF  
WASH LOAD  
speed  
Two examples of  
maximum wash loads  
for different types of  
fabric:  
Mixed Prewash  
30  
6kg  
20 minutes  
Slow  
A
B
C
White Cotton & Linen  
without special finishes.  
95  
60  
6kg  
6kg  
2 hours 20minutes  
2 hours 10minutes  
Fast  
Fast  
COTTON  
Super Wash  
White Cotton & Linen  
2
1
6
6
1
4
Bath Towels  
Hand Towel  
Shirts  
Colourfast Cotton, Linen  
or Viscose without special  
finishes.  
D
60  
6kg  
1 hour 50minutes  
Fast  
Blouses  
Pair of Pyjamas  
Items of  
Fast Wash  
Colourfast Cottons & Linen  
E
F
60  
40  
5kg  
6kg  
1 hour  
Fast  
Fast  
Underwear  
Non-colourfast Cottons,  
Linen & Viscose  
1 hour 45minutes  
= 6kg  
SYNTHETIC  
Coloured Synthetics:  
coloured Nylon, Polyester,  
Acrylic and Cotton mixtures,  
Cotton or Viscose with special 50  
finishes.  
coloured Polyester and Cotton  
mixtures.  
2
4
4
1
4
Children’s Dresses  
G
3kg  
3kg  
1 hour 10minutes  
1 hour 5minutes  
Slow  
Slow  
Shirts  
Blouses  
Pair of Pyjamas  
Items of  
Acrylics:  
Acrylics and tri-acetate blends 40  
of these fabrics with Wool,  
Polyester and Wool blends.  
H
J
Underwear  
= 3kg  
Handwash Wool  
40  
1.5kg  
3kg  
50minutes  
55minutes  
Slow  
Silks  
30  
Gentle  
K
L
Handwash Wool Approved  
‘The wool wash cycle on the  
WF series of Hotpoint washing  
machines has been tested and  
approved by the Woolmark  
Company for washing gar-  
ments labelled as “hand wash,  
provided that the garments  
are washed in accordance to  
the instructions issued by the  
manufacturer of this washing  
machine.’  
Fast Wash  
Handwash  
Mixed  
30  
25  
3kg  
3kg  
3kg  
6kg  
3kg  
30minutes  
45minutes  
30minutes  
15minutes  
13minutes  
2minutes  
Slow  
Gentle  
Slow  
Fast  
M
Rinse and Spin  
Fast Spin  
Cotton  
Delicates  
All  
Slow Spin  
Slow  
Pump Out  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using your Machine  
STEP 5  
Door Locked indicator light Progress indicator lights  
Option buttons  
Programme listing  
Digital Display  
WARNINGS:  
In the unlikely  
event of something  
not working, see  
‘Troubleshooting’  
STEP 8.  
‘On/Off’ button  
‘Start/Cancel’  
button  
Variable Temperature button  
Variable Spin Speed button  
Programme selector dial  
On-Off / Selecting a programme...  
The machine is switched on by pressing the ‘On/Off’ button for 2 seconds. All the indicator lights will light up for a few seconds and  
the ‘Door Locked’ indicator light will flash once.  
Turn the programme selector dial to the desired programme. Load the laundry and detergent. Select the options you require.  
Press the ‘Start/Cancel’ button for 2 seconds to start the programme.  
To stop or change a programme...  
Press the ‘Start/Cancel’ button for 2 seconds.  
Select ‘Pump Out’ on the programme selector dial.  
When the machine has finished emptying, turn the programme selector dial to the new programme (you may need to add  
detergent). Press the ‘Start/Cancel’ button to start the programme.  
If you cancel a hot wash programme, take care when removing the laundry, it might still be very hot.  
Progress indicator lights...  
Door Locked indicator light...  
The ‘Door Locked’ indicator light will come on two seconds after  
you press the ‘Start/Cancel’ button and will stay lit throughout the  
programme. A short time after the programme has finished the  
indicator light will go out and you can then open the door.  
Selected programmes will not start if the door is not closed  
properly, the ‘Door Locked’ indicator light will flash to show this.  
The display will also show the word ‘door.  
These will light up when you choose a programme, to indicate the  
progress of the selected programme. When started, the first light in  
the cycle will stay lit and as the programme  
progresses, successive lights will come on until the  
programme finishes.  
During a wash programme the display will show the time remaining  
to the end of the programme.  
Push the door shut until you hear the catch click.  
The machine will show on the display if there is a problem:  
H20  
A problem with the water supply.  
Check that the taps are turned on and working.  
Please close the machine door properly.  
Indicates a machine fault.  
door  
F000  
Please note the number shown and refer to STEP8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Options  
STEP 6  
To select an option, press the button and you will see a light come on alongside the button.  
Press again to cancel, and the light will go out.  
Button Selection:  
NOTE: If the option selected is not available with the programme, the light will flash briefly.  
Reduce Creases  
Reduces wash action and spin speed, meaning less ironing for  
Time Saver  
Saves up to a third on the programme time.  
delicate clothes.  
This option is only available with programmes B, D, G and H.  
This option is only available with programmes C, E, G, H and  
Rinse & Spin.  
Mini Load...  
Rinse Hold  
Clothes will be held in the final rinse water, keeping them fresh  
until you are ready to complete the programme.  
Complete the final spin by pressing the Rinse Hold button when  
the light is flashing.  
For washing a smaller load.  
In addition to reducing actual washing time, this option will  
reduce water and energy consumption by up to 50%.  
Note: You can reduce the amount of detergent you use with this  
wash.  
This is not available with programmes A, J, L M, Rinse & Spin  
or Spin Only.  
This option is not available with programmes A, F, J, K, L, M  
and Spin Only.  
Time Delay...  
(Models WF645, WF640 and WF630 only)  
Extra Rinse...  
(Model WF620 only)  
This option can delay the start of your wash programme by up  
to 24 hours. The display will show the delay you have chosen.  
Each press of the option button will add a delay of one hour. If  
you press after 24 shows on the display the machine will reset  
the time delay and show ‘OFF’ in the display, any press after this  
will start counting again from one hour  
For large wash loads and items for young children or people  
with sensitive skin.  
This option adds a rinse.  
This is not available with programmes A, J, K, L, M or Spin  
Only.  
Variable Spin Speed  
Variable Temperature  
This allows you to reduce the wash  
temperature below the maximum for the  
programme you have chosen.  
This allows you to reduce the spin speed  
below the maximum for the programme you  
have chosen.  
Each press of the button will reduce the  
wash temperature by 5˚C. The new wash  
temperature will be shown in the display.  
If you press again after ‘OFF’ has been  
displayed, the machine will revert to the  
original higher wash temperature.  
Each press of the button will reduce the spin  
speed to the next lower band. The new spin  
speed will be shown in the display.  
If you press again after ‘OFF’ has been  
displayed, the machine will revert to the  
original higher spin speed.  
WARNINGS:  
DO NOT allow  
children to play  
with the appliance  
or tamper with the  
controls.  
DO NOT overload During the wash DO NOT open the DO NOT try to  
If you stop a programme  
the appliance!  
It may damage  
the laundry and  
reduce the  
cycle, remember  
that the door  
glass may  
become hot to  
the touch.  
dispenser drawer  
during any  
programme.  
open the door  
when the ‘Door  
Locked’ indicator  
light is on.  
part way through a wash  
or there is a power cut,  
take care when opening  
the door, the machine  
may contain hot water.  
quality of the  
wash.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A Typical Wash Programme  
STEP 7  
1
2
3
4
5
Add detergent (and  
fabric conditioner if  
required) to the  
Press the ‘On/Off‘  
button.  
Reduce the spin  
speed if you wish  
using the variable spin  
speed button (see  
STEP 6).  
Sort laundry into  
groups by washcare  
labels.  
Load the machine,  
making sure that the  
laundry is not  
trapped in the door.  
Close the door by  
pushing it until it  
clicks.  
Select any optional  
wash feature(s) that  
you may require by  
pressing the  
appropriate button(s),  
indicator lights will  
show what you have  
chosen (see STEP 6).  
Turn the programme  
dispenser drawer (see selector dial to the  
STEP 3).  
programme required  
Refer to the detergent (see STEP 4).  
manufacturer’s  
dosage instructions.  
6
8
9
7
When all selections  
have been made  
press the  
Start/Cancel’ button.  
To stop a programme  
before it has finished:  
press the  
Start/Cancel’ button  
again.  
Turn the programme  
selection dial to  
‘Pump Out.  
Reduce the wash  
temperature if you  
wish using the variable  
temperature button  
(see STEP 6).  
During the wash, the A short time after the  
progress indicator  
programme has  
lights will show what finished the ‘Door  
stage in the cycle the Locked’ indicator light  
programme has  
reached.  
will go out and you  
can open the door.  
The digital display  
will show the time  
remaining to the end  
of the programme  
When the machine has finished emptying  
you can select a new programme.  
Press the ‘Start/Cancel’ button to start the  
new programme.  
We recommend that  
you switch off the  
electricity and water  
supply.  
Automatic Features...  
Auto half load  
Auto half load saves you time and money when washing smaller loads.  
Water levels are automatically adjusted to cater for the different loads.  
Unbalanced load  
Your machine has an inbuilt feature to prevent it spinning with an unbalanced load. This will minimise excessive vibration and  
prolong the life of the machine. Before each spin the machine ‘senses’ the load within the drum and if the machine considers the  
load to be unbalanced, it will not automatically spin. Instead the machine will try to redistribute the load to achieve balance by  
tumbling backwards and forwards. If it is unable to balance the load after the sixth attempt the machine will abort the spin  
process.  
If this safety feature is encountered you can spin the load after first opening the door, redistributing the load and selecting a fast or  
slow, spin only programme. In the case of small loads or single items you may try adding some extra items of a comparable size to  
help balance the load.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STEP 8  
Washcare Tips:  
Do not overload the machine  
(maximum load 6kg).  
MY MACHINE MAKES A  
THE DISPENSER WILL NOT  
CLOSE PROPERLY  
MY MACHINE WILL NOT  
START  
MY MACHINE DOES NOT  
PUMP OUT WATER  
In addition to reducing the  
quality of the wash, this may also  
damage your laundry and the  
machine.  
NOISE OR VIBRATES IN A  
SPIN PROGRAMME.  
MY MACHINE IS LEAKING  
Why not pin this  
chart up near your  
machine or inside  
a cupboard door...  
where you can  
We strongly recommend that you  
do not wash underwired bras in  
this machine. Should the wires  
become detached it could cause  
damage to your clothes and the  
machine. If the washcare label  
states that the bra is machine  
washable, then we advise placing  
it in a sealed pillow case or a  
similar washbag. Remember, you  
will be charged for a service call  
resulting from a detached bra  
wire.  
Is the drawer clogged with  
detergent?  
Close the door. Choose a  
programme and then press ‘On/Off’  
Check all loose items, such as  
coins, have been removed  
from the laundry.  
Has the drain hose been installed  
correctly? Ensure it is not blocked  
Are the fill hoses on correctly?  
If not tighten them.  
Does the washer need  
replacing?  
or kinked.  
Clean the dispenser drawer, see  
STEP 3:‘The Dispenser Drawer’  
Does the ‘door indicator’ light  
come on after 2 seconds?  
easily refer to it?  
Are the drainage unit, standpipe  
or under sink connections free  
from blockages?  
Have both transit bolts been  
removed from the machine?  
Check the drawer is properly  
aligned.  
Is your water pressure too  
high?  
Has ‘Rinse Hold’ been selected?  
The light will flash until the button  
is pressed again.  
Is the machine plugged in  
and switched on?  
Turn the main supply tap  
down.  
Have you adjusted the feet  
to stabilise the machine?  
Do not use the machine if the  
item to be washed does not have  
a wash label.  
SUDS ARE COMING FROM  
THE DISPENSER DRAWER  
Is the socket OK? Test with  
another appliance to check.  
Is the standpipe or household  
drain blocked.  
Before washing laundry we  
recommend that you do the  
following:  
Press the ‘Rinse Hold’ button  
again.  
See STEP 2: Installation  
Check the correct amount of  
suitable detergent has been used,  
refer to manufacturer’s  
Pre-treat awkward stains with  
washable treatments.  
Do not wash any items that have  
previously been treated with  
solvents.  
Close zips, fasten belts, tie strings  
and close press studs to prevent  
tangling.  
Empty ALL objects from pockets  
as they may damage the clothes  
and the machine.  
See STEP 2: Installation  
Is the fuse in the plug OK?  
recommendations.  
You may need to call in a  
plumber.  
If you have used the wrong type of  
detergent, select a Rinse programme  
to flush out your machine.  
Clear any blockages that have  
been found  
Plug the machine in and  
turn the socket switch on.  
If your machine is still not working  
contact:  
Repair Service and Information Desk  
UK 08709 066 066  
Republic of Ireland 1850302 200  
MY LAUNDRY HAS NOT  
SPUN DRY.  
Is the machine connected to  
a sink waste system?  
Is steam coming from  
the dispenser drawer?  
If possible use another socket  
for the machine.  
NOT ALL OF THE DETERGENT  
HAS BEEN FLUSHED AWAY  
Check the blocked end of the  
under sink drainage unit has  
been cut off.  
Did you reduce the spin speed of  
your selected wash programme?  
See STEP 6: Options  
You will be asked for the following  
details: Name and Address, Post  
Code,Telephone Number, Date of  
Purchase, Colour and Model/Serial  
Numbers - which can be found on  
the inside of the door.  
The machine is designed to  
release steam from the dispenser  
drawer during hot washes.  
If not replace it, see STEP 1:  
Electricity Supply  
Check that your water supply  
taps are turned on fully.  
Was a short spin programme  
used on a non-synthetic load.  
Check the feet have been  
levelled.  
Remember, you will be charged  
for a service call to rectify a  
malfunction resulting from  
objects, such as coins, pens, hair  
grips etc. falling from pockets.  
Limit the size of absorbent loads  
ie. towels, to 3kg (7lb) to give  
good washing and rinsing results.  
Place small items in a wash bag.  
Always follow the care label on  
items when choosing the wash  
programme.  
WATER COLLECTS IN THE  
FABRIC DISPENSER  
COMPARTMENT  
Clear and precise details of the query  
or fault.  
Check the inlet hoses are not  
kinked.  
MY MACHINE STOPS  
BEFORE A SPIN  
PROGRAMME.  
There has been an unbalanced load  
and the machine could not spin.  
See ‘Automatic Features’ STEP 7.  
Is your hot water pressure low?  
If the digital display shows a Fault  
code number (see STEP 5), please  
advise us.  
You may need a cold fill adaptor  
to run your machine as cold fill  
only. See ‘Installation, STEP 2.  
THE PROGRAMME TAKES A  
LONG TIME  
Clean fabric dispenser drawer.  
See STEP 3:‘The Dispenser  
Drawer.  
The ‘Rinse Hold’ button has  
been pressed, this will hold  
laundry in the final rinse water,  
until the button is pressed  
again.  
Remember, you will be charged for a  
service call if a problem with your  
machine is caused by incorrect  
installation or misuse.  
Did the water pump out?  
If not see ‘MY MACHINE DOES  
NOT PUMP OUT WATER.  
Check for low temperature and  
low pressure of the hot and cold  
water supply.  
Wash non-colourfast items or  
really dirty laundry separately as  
they may affect other items.  
Remember, you will be charged for a service call for problems caused by incorrect installation, non-removal of transit bolts or packaging, leaks from household pipework, loose or blocked fill and drain hoses.  
Washing items that DO NOT have a wash label or washing items that are not intended as machine washable and NOT emptying contents from pockets may cause pump or drain blockages, or may damage components within the machine.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting to Know your Appliance  
Unplug your appliance when cleaning it or carrying out maintenance.  
Model shows the maximum features available on an Aquarius+  
washing machine.  
Cleaning the Exterior:  
Control Panel  
Dispenser Drawer  
Use a damp cloth or silicon polish to clean the exterior surfaces of the  
appliance.  
Cleaning the Door Bowl:  
Clean the internal surface of the door bowl regularly with a soft cloth.  
A build up of soap powder and water hardness residue may result in  
water leaking from the door.  
Interlocking door  
and release lever  
Cleaning the Dispenser Drawer & Compartments:  
It is advisable to clean the dispenser drawer regularly:  
Pull the drawer out until it reaches its stop.  
Hooked End Support  
Mains Cable  
Rating Plate  
1
Press the drawer release latch  
2
down to remove the dispenser  
drawer.  
Adjustable Feet  
Hot Water inlet point and  
supplied Hose (Red or Grey end)  
Clean and dry the  
3
dispenser drawer,  
syphons, grate and  
fabric conditioner exit  
channel (A).  
Also, regularly clean the  
outlet pipe area (B).  
Cold Water inlet point and  
supplied Hose (Blue end)  
Plumbing Indicator Line label  
B
A
Transit Bolts (both MUST be removed  
before using your machine).  
Relocate the dispenser drawer and push it  
firmly back into place.  
4
Drainage Hose  
WARNINGS:  
Do not try to clean any  
part of the dispenser  
drawer while the machine  
is working.  
Do not clean any part of the  
machine with abrasive cleaners,  
scouring agents, acids, any  
bleaches or metal polish, as  
they may cause damage.  
Wheels  
Key Contacts  
After Sales Service  
Over 1200 trained specialists, directly employed by us, ensure that you can have complete confidence in both the appliances and  
services we offer.  
Repair Service and Information Desk  
UK: 08709 066 066  
Extended Warranties  
UK: 08709 088 088  
(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)  
(Open 8 to 8 Mon - Sun)  
Republic of Ireland: 1850 502 200  
Republic of Ireland: 1850 302 200  
Note: Our operators will require the following information:  
Genuine Parts and Accessories  
UK: 08709 077 077  
The Model number  
(which can be found on  
the control panel)  
(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)  
The Serial number  
(which can be found on the  
inner door trim)  
Republic of Ireland: (01) 842 6836  
Download from Www.Somanuals.com. All Manuals Search And Download.  
After Sales Service  
Hotpoint guarantee  
“Satisfaction guaranteed or your money back”  
“No company is better positioned to offer an after sales service on  
a Hotpoint appliance than us - the manufacturer.  
We give you a unique ‘satisfaction guaranteed’ promise - valid  
for 90 days - after you have purchased your Hotpoint  
appliance. If there is a technical problem simply call Hotpoint  
Repair service or visit our web-site at  
arrange for an engineer to call. If the technical problem is not  
resolved under this guarantee, we will replace your machine  
or, if you prefer, give you your money back.  
As part of our commitment to you, all Hotpoint appliances have the  
added benefit of a fully inclusive parts and labour guarantee for the first  
12 months. In addition to this you also have the advantage of free  
replacement parts for the first 5 years when fitted by a Hotpoint  
engineer. When the 12 months parts and labour guarantee expires we  
offer the following after sales service options:  
Repair Service and Information Help Desk  
UK: 08709 066066  
Republic of Ireland: 1850 302 200  
Note: Our operators will require the Model number and the Serial number  
of your appliance.  
All Hotpoint appliances carry a fully inclusive 12 month parts  
and labour guarantee as well as free replacement parts for the  
first 5 years (except microwaves, selected integrated  
appliances and cooker hoods, which have a one year  
guarantee) provided that they are fitted by a Hotpoint  
engineer.  
Available 364 days a year with a fast, effective and value for money  
service. We have the largest white goods repair service in the UK with over  
1200 of our own fully trained engineers. All repairs include a parts and  
labour guarantee for 12 months from the date of the repair.  
If you require any information or have any questions about your  
appliance, our operators are on hand with help and advice.  
All this ensures that you will receive the best available after sales service  
possible.  
Guarantee terms and conditions  
Your guarantee is only applicable in the United  
Kingdom or Republic of Ireland and is subject to the  
following provisions that your appliance:  
Has been installed and used correctly in accordance with  
this instruction booklet.  
Has been used solely for domestic purposes and is located  
on domestic premises (ie. not for commercial or trade  
use).  
Extended Warranties  
UK: 08709 088 088  
Republic of Ireland: 1850 502 200  
Has been properly connected to a suitable electrical  
supply voltage as stated on the appliance rating plate.  
Has not been subject to misuse, accident, modified or  
repaired by anyone other than one of our own service  
engineers.  
Whether you have just one or a number of Hotpoint appliances in your  
kitchen, we offer two service cover plans to give you total peace of mind.  
Repair Protection Plan - FREE service repairs for a single Hotpoint  
appliance during the period of cover.  
Kitchen Cover  
- FREE service repairs for all your Hotpoint  
appliances less than 8 years old.  
For pre purchase information on any other Hotpoint  
product,  
Genuine Parts and Accessories  
UK: 08709 077 077  
Republic of Ireland: (01) 842 6836  
call: 08701 50 60 70 or visit: www.hotpoint.co.uk  
A wide range of genuine parts and accessories are available from our  
hotline or through our web site.  
Genuine parts and accessories, extended warranties and service  
repairs are all available on our web-site at:  
Recycling & Disposal Information  
As part of Hotpoint’s continued commitment to helping the environment,  
Hotpoint reserves the right to use quality recycled components to keep down  
customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully.  
To minimise risk of injury to children, remove the door, plug and cut mains cable  
off flush with the appliance. Dispose of these parts separately to ensure that the  
appliance can no longer be plugged into a mains socket, and the door cannot be  
locked shut.  
Merloni Elettrodomestici UK Limited, Morley Way, Peterborough, PE2 9JB.  
PRINTED BY SIMLEX FOUR ASHES, WOLVERHAMPTON.  
.
08/2004  
-
195044004.01  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Gravely Lawn Mower Accessory 890015 User Manual
Hamilton Beach Air Cleaner 840117900 User Manual
Hampton Bay Outdoor Ceiling Fan 122 135 User Manual
Harman Kardon DVD Player DVD 23 User Manual
Harman Stereo Amplifier GT X424 User Manual
Havis Shields Automobile Parts C B1 User Manual
Honeywell DVR HRTL One User Manual
Hotpoint Cooktop 52 TCW S User Manual
IBM Network Card 3301690 User Manual
IBM Personal Computer G544 5774 01 User Manual