How to get the best from
Your Range
Contents
Aluminum Foil
Anti-Tip Device
21, 23, 25, 30
2, 3, 35, 43
Oven Bottom
Oven Vents
30
Use and Care
& Installation
of Models
RGB744
15, 33
Appliance Registration
Before You Call for Service 53, 54
2
Roasting, Roasting Guide 21, 22
Self-Cleaning
25–27
Thermostat Adjustment—
Do It Yourself
Shelves
Power Outage
15, 16
13
20
Care and Cleaning
Clock and Timer
28–33
12, 13
Safety Instructions
Surface Cooking
3–5
8–10
RGB745
Consumer Services
Important Phone Numbers
51
51
Burners
Control Settings
8–10
8, 9
Features
6, 7
Cooktop Comparison
Cookware Tips
8
10
Installation Instructions 34–43
LP Conversion
Flooring Under Range
44–50
36
Flame Size
Lighting Instructions
9
8
Leveling
Model and Serial Numbers
43
2
Warranty
Back Cover
Oven
Baking
14–27
16–19
Broiling, Broiling Guide 23, 24
Control Settings
11
Door Removal
31
GE Answer Center®
800.626.2000
Light; Bulb Replacement 14, 32
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using this appliance.
• Be sure all packing materials are removed from
IMPORTANT SAFETY NOTICE
the range before operating it to prevent fire or
• The California Safe Drinking Water and Toxic
Enforcement Act requires the Governor of California
to publish a list of substances known to the state
to cause cancer, birth defects or other reproductive
harm, and requires businesses to warn customers
of potential exposure to such substances.
smoke damage should the packing material ignite.
• Be sure your range is correctly adjusted by a
qualified service technician or installer for the
type of gas (natural or LP) that is to be used.
Your range can be converted for use with either
type of gas. See the Installation Instructions.
Gas appliances can cause minor exposure to
four of these substances, namely benzene, carbon
monoxide, formaldehyde and soot, caused primarily
by the incomplete combustion of natural gas or
LP fuels. Properly adjusted burners, indicated by a
bluish rather than a yellow flame, will minimize
incomplete combustion. Exposure to these
WARNING: These adjustments must be made by a
qualified service technician in accordance with the
manufacturer’s instructions and all codes and
requirements of the authority having jurisdiction.
Failure to follow these instructions could result in
serious injury or property damage. The qualified
agency performing this work assumes responsibility
for the conversion.
substances can be minimized by venting with an
open window or using a ventilation fan or hood.
• After prolonged use of a range, high floor
temperatures may result and many floor
coverings will not withstand this kind of use.
Never install the range over vinyl tile or linoleum
that cannot withstand such type of use. Never
install it directly over interior kitchen carpeting.
• Fluorescent light bulbs and safety valves on
standing pilot ranges contain mercury. If your
model has these features, they must be recycled
according to local, state and federal codes.
When You Get Your Range
• Have the installer show you the location of the
range gas cut-off valve and how to shut it off
if necessary.
Using Your Range
WARNING—All ranges
can tip and injury could result. To
prevent accidental tipping of the
range, attach it to the wall and floor by
installing the Anti-Tip device supplied.
To check if the device is installed and
engaged properly, carefully tip the
• Have your range installed and properly
grounded by a qualified installer, in accordance
with the Installation Instructions. Any adjustment
and service should be performed only by qualified
gas range installers or service technicians.
•
Do not attempt to repair or replace any part of
your range unless it is specifically recommended
in this guide. All other servicing should be referred
to a qualified technician.
range forward. The Anti-Tip device should engage
and prevent the range from tipping over.
If you pull the range out from the wall for any
reason, make sure the device is properly engaged
when you push the range back against the wall.
If it is not, there is a possible risk of the range
tipping over and causing injury if you or a child
stand, sit or lean on an open door.
Please refer to the Anti-Tip device information
in this guide. Failure to take this precaution could
result in tipping of the range and injury.
• Plug your range into a 120-volt grounded
outlet only. Do not remove the round grounding
prong from the plug. If in doubt about the grounding
of the home electrical system, it is your personal
responsibility and obligation to have an ungrounded
outlet replaced with a properly grounded, three-
prong outlet in accordance with the National
Electrical Code. In Canada, the appliance must be
electrically grounded in accordance with the
Canadian Electrical Code. Do not use an extension
cord with this appliance.
• Do not leave children alone or unattended
where a range is hot or in operation.
They could be seriously burned.
• Locate the range out of kitchen traffic path
and out of drafty locations to prevent pilot
outage (on standing pilot models) and poor
air circulation.
• For your safety, never use your appliance for
warming or heating the room.
(continued next page)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
(continued)
• CAUTION: ITEMS OF INTEREST TO
• Always use the LITE position (on electric
ignition models) or the HI position (on standing
pilot models) when igniting the top burners and
make sure the burners have ignited.
• Never leave the surface burners unattended at
high flame settings. Boilovers cause smoking
and greasy spillovers that may catch on fire.
• Adjust the top burner flame size so it does not
extend beyond the edge of the cookware.
Excessive flame is hazardous.
CHILDREN SHOULD NOT BE STORED IN
CABINETS ABOVE A RANGE OR ON THE
BACKSPLASH OF A RANGE—CHILDREN
CLIMBING ON THE RANGE TO REACH
ITEMS COULD BE SERIOUSLY INJURED.
• Do not allow anyone to climb, stand or hang
on the door, broiler drawer or cooktop. They
could damage the range and even tip it over,
causing severe personal injury.
• Let the burner grates and other surfaces cool
before touching them or leaving them where
children can reach them.
• Never wear loose fitting or hanging garments
while using the appliance. Be careful when
reaching for items stored in cabinets over the
cooktop. Flammable material could be ignited if
brought in contact with flame or hot oven surfaces
and may cause severe burns.
• Do not use water on grease fires. Never pick up
a flaming pan. Turn the controls off. Smother a
flaming pan on a surface unit by covering the
pan completely with a well-fitting lid, cookie sheet
or flat tray. Use a multi-purpose dry chemical or
foam-type fire extinguisher.
Flaming grease outside a pan can be put out by
covering it with baking soda or, if available, by
using a multi-purpose dry chemical or foam-type
fire extinguisher.
Flame in the oven can be smothered completely by
closing the oven door and turning the oven off or
by using a multi-purpose dry chemical or foam-
type fire extinguisher.
• Do not store flammable materials in an oven, a
range broiler or storage drawer or near a cooktop.
• DO NOT STORE OR USE COMBUSTIBLE
MATERIALS, GASOLINE OR OTHER
FLAMMABLE VAPORS AND LIQUIDS IN
THE VICINITY OF THIS OR ANY OTHER
APPLIANCE.
• Do not let cooking grease or other flammable
materials accumulate in or near the range.
•
Use only dry pot holders—moist or damp pot holders
on hot surfaces may result in burns from steam.
• Do not let pot holders come near open flames
when lifting cookware. Do not use a towel or other
bulky cloth in place of a pot holder.
• To minimize the possibility of burns, ignition
of flammable materials and spillage, turn cookware
handles toward the side or back of the range
without extending over adjacent burners.
• Always turn the surface burners to off before
removing cookware.
• Carefully watch foods being fried at a high
flame setting.
• Never block the vents (air openings) of the
range. They provide the air inlet and outlet that
are necessary for the range to operate properly
with correct combustion. Air openings are located
at the rear of the cooktop, at the top and bottom of
the oven door, and at the bottom of the range under
the broiler drawer.
• Do not use a wok on models with sealed burners
if the wok has a round metal ring that is placed
over the burner grate to support the wok. This
ring acts as a heat trap, which may damage the
burner grate and burner head. Also, it may cause
the burner to work improperly. This may cause a
carbon monoxide level above that allowed by
current standards, resulting in a health hazard.
• Foods for frying should be as dry as possible. Frost
on frozen foods or moisture on fresh foods can cause
hot fat to bubble up and over the sides of the pan.
• Use the least possible amount of fat for effective
shallow or deep-fat frying. Filling the pan too full
of fat can cause spillovers when food is added.
• When cooking pork, follow the directions exactly
and always cook the meat to an internal temperature
of at least 170°F. This assures that, in the remote
possibility that trichina may be present in the meat,
it will be killed and the meat will be safe to eat.
• Use a deep fat thermometer whenever possible to
prevent overheating fat beyond the smoking point.
• Never try to move a pan of hot fat, especially a
Surface Cooking
deep fat fryer. Wait until the fat is cool.
• Always heat fat slowly, and watch as it heats.
• When using glass cookware, make sure it is
designed for top-of-range cooking.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
• If a combination of oils or fats will be used
in frying, stir together before heating or as fats
melt slowly.
• Keep the oven free from grease buildup.
• Pulling out the shelf to the shelf-stop is a
convenience in lifting heavy foods. It is also a
precaution against burns from touching hot
surfaces of the door or oven walls. The lowest
position “R” is not designed to slide.
• Do not heat unopened food containers. Pressure
could build up and the container could burst,
causing an injury.
• Do not use aluminum foil anywhere in the oven
except as described in this guide. Misuse could
result in a fire hazard or damage to the range.
• When using cooking or roasting bags in the
oven, follow the manufacturer’s directions.
• Use proper pan size—Avoid pans that are
unstable or easily tipped. Select cookware having
flat bottoms large enough to properly contain food
and avoid boilovers and spillovers and large
enough to cover burner grate. This will both save
cleaning time and prevent hazardous accumulations
of food, since heavy spattering or spillovers left
on range can ignite. Use pans with handles that
can be easily grasped and remain cool.
• Keep all plastics away from the top burners.
• Do not leave plastic
items on the cooktop—
they may melt if left
too close to the vent.
• Use only glass cookware that is recommended
for use in gas ovens.
• Do not leave any items Vent appearance and location vary
on the cooktop.
• Always remove the broiler pan from range as
soon as you finish broiling. Grease left in the pan
can catch fire if oven is used without removing
the grease from the broiler pan.
• When broiling, if meat is too close to the flame,
the fat may ignite. Trim excess fat to prevent
excessive flare-ups.
The hot air from the vent may ignite flammable
items and will increase pressure in closed
containers, which may cause them to burst.
• To avoid the possibility of a burn, always be
certain that the controls for all burners are at
the off position and all grates are cool before
attempting to remove them.
• Make sure the broiler pan is in place correctly
to reduce the possibility of grease fires.
• If you should have a grease fire in the broiler pan,
turn off oven control, and keep broiler drawer and
oven door closed to contain fire until it burns out.
• When flaming foods are under the hood, turn
the fan off. The fan, if operating, may spread
the flames.
• If range is located near a window, do not hang
long curtains that could blow over the top burners
and create a fire hazard.
Self-Cleaning Oven
• Clean only parts listed in this Use and Care Guide.
• Do not clean door gasket. The door gasket is
essential for a good seal. Care should be taken not
to rub, damage or move the gasket.
• Do not use oven cleaners. No commercial oven
cleaner or oven liner protective coating of any kind
should be used in or around any part of the oven.
Residue from oven cleaners will damage the inside
of the oven when the self-clean cycle is used.
• Before self-cleaning the oven, remove broiler
pan and rack and other cookware.
• Be sure to wipe up excess spillage before
starting the self-cleaning operation.
• When a pilot goes out (on standing pilot models),
you will detect a faint odor of gas as your signal
to relight the pilot. When relighting the pilot,
make sure burner controls are in the off position,
and follow instructions in this book to relight.
• If you smell gas, and you have already made sure
pilots are lit (on standing pilot models), turn off the
gas to the range and call a qualified service technician.
Never use an open flame to locate a leak.
Baking, Broiling and Roasting
• Do not use the oven for a storage area.
Items stored in the oven can ignite.
• Place the oven shelves in the desired position
while the oven is cool.
• If the self-cleaning mode malfunctions, turn
the oven off and disconnect the power supply.
Have it serviced by a qualified technician.
• Stand away from the range when opening the
door of a hot oven. The hot air and steam that
escapes can cause burns to hands, face and eyes.
SAVE THESE
INSTRUCTIONS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES OF YOUR RANGE
Features and appearance vary.
1
2
3
4
COOK
TIME
CLOCK
TIMER
OVEN
CYCLE
ON/OFF
RGB745 shown
START
TIME
ON/OFF
FF
ON/O
5
20
19
6
7
8
9
18
17
10
16
15
14
11
13
12
Sealed Burners
Standard Twin Burners
Burner Cap
Drip Pan
(on some
models)
Drip Pan
(on some
models)
Burner Head
Burner
Your range is equipped with one of the two types of surface burners shown above.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Feature Index
Explained
on page
(Not all models have all features. Appearance of features varies.)
1 OVEN SET Knob
11, 16, 18, 19,
21, 23, 26, 32
2 Clock and Minute Timer
3 OVEN CYCLE Light
4 OVEN TEMP Knob
12, 13, 18
11, 12
11, 16, 18–21,
23, 26, 32
5 Oven Vent
4, 5, 15, 33
4, 8–10, 25, 28–30
4, 8, 9, 28, 29, 32
16, 18, 21, 23, 25–27
15, 16, 26, 31
6 Grates, Drip Pans (on some models) and Surface Burners
7 Surface Burner Control Knobs
8 Oven Door Latch Use for self-cleaning cycle only.
9 Oven Shelf Supports
Shelf positions for cooking are suggested in the Baking,
Roasting and Broiling sections.
10 Oven Door Gasket
5, 25, 27, 31
4, 32
11 Storage Drawer or Kick Panel (depending on model)
12 Broiler Pan and Grid
5, 21, 23–25, 31
2, 36
13 Model and Serial Numbers
On front frame of range, behind storage drawer or kick panel.
14 Lift-Off Oven Door Easily removed for oven cleaning.
23, 24, 31
15 Anti-Tip Device
2, 3, 35, 43
Lower right rear corner on range back. See the Installation Instructions.
16 Removable Oven Bottom
30
17 Oven Shelves Easily removed or repositioned on shelf supports.
5, 14–18, 21,
23, 25–27, 31
18 Oven Interior Light
19 Oven Light On/Off Switch (on some models)
20 Cooktop
14, 25, 32
14
30, 33
Air Vents
4, 5, 15, 33
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW DOES THIS COOKTOP COMPARE
TO YOUR OLD ONE?
Your new cooktop has gas burners. If you are used
The best types of cookware to use, plus heat-up and
cool-down times, depend upon the type of burner or
surface unit you have.
to cooking with induction or other electric surface
units, you will notice some differences when you use
gas burners.
The following chart will help you to understand the
differences between gas burner cooktops and any
other type of cooktop you may have used in the past.
Type of Cooktop
Gas Burners
Description
How it Works
Regular or sealed
gas burners use
either LP gas
Flames heat the pans directly. Pan flatness is not critical to cooking results, but
pans should be well balanced. Gas burners heat the pan right away and change
heat settings right away. When you turn the control off, cooking stops right away.
or natural gas.
Radiant
(Glass Ceramic)
Cooktop
Electric coils
under a glass-
ceramic cooktop.
Heat travels to the glass surface and then to the cookware, so pans must be flat on
the bottom for good cooking results. The glass cooktop stays hot enough to
continue cooking after it is turned off. Remove the pan from the surface unit if
you want cooking to stop.
Induction
High frequency
induction coils
under a glass
surface.
Pans must be made of ferrous metals (metal that attracts a magnet). Heat is
produced by a magnetic circuit between the coil and the pan. Heats up right away
and changes heat settings right away, like a gas cooktop. After turning the control
off, the glass cooktop is hot from the heat of the pan, but cooking stops right away.
Electric Coil
Flattened metal
tubing containing
electric resistance
wire suspended
over a drip pan.
Heats by direct contact with the pan and by heating the air under the pan. For best
cooking results, use good quality pans. Electric coils are more forgiving of
warped pans than radiant or solid disks. Heats up quickly but does not change
heat settings as quickly as gas or induction. Electric coils stay hot enough to
continue cooking for a short time after they are turned off.
Solid Disk
Solid cast iron
disk sealed to the
cooktop surface.
Heats by direct contact with the pan, so pans must be flat on the bottom for good
cooking results. Heats up and cools down more slowly than electric coils. The
disk stays hot enough to continue cooking after it is turned off. Remove the pan
from the solid disk if you want the cooking to stop.
SURFACE COOKING
Lighting Instructions
Your surface burners are lighted by electric ignition,
eliminating the need for standing pilot lights with
constantly burning flames.
The electrode of the spark igniter is exposed.
When one burner is turned to LITE, all the burners
spark. Do not attempt to disassemble or clean
around any burner while another burner is on.
An electric shock may result, which could cause
you to knock over hot cookware.
In case of a power failure, you can light the surface
burners on your range with a match. Hold a lighted
match to the burner, then turn the knob to the LITE
position. Use extreme caution when lighting
burners this way.
Surface burners in use when an electrical power
failure occurs will continue to operate normally.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Surface Burner Controls
The knobs that turn the surface burners on and off are
located on the control panel in front of the burners.
On ranges with sealed burners:
• The smaller burner (right rear position) will give
the best simmer results. It offers precise cooking
performance for delicate foods, such as sauces or
foods which need to cook over low heat for a
long time. It can be turned down to a very low
simmer setting.
The two knobs on the left control the left front and
left rear burners. The two knobs on the right control
the right front and right rear burners.
• The right front burner is higher powered than the
others and will bring liquids to a boil quicker
(natural gas installations only).
Before Lighting a Burner
To Light a Surface Burner
• If drip pans are supplied with your range,
they should be used at all times.
Push the control knob in
and turn it to LITE. You
will hear a little ‘‘clicking’’
noise—the sound of the electric
spark igniting the burner.
• Make sure all grates on the range are in place
before using any burner.
After Lighting a Burner
• After the burner ignites, turn the knob to adjust the
flame size.
• Do not operate a burner for an extended period of
time without cookware on the grate. The finish on the
grate may chip without cookware to absorb the heat.
• Check to be sure the burner you turned on is the one
you want to use.
• Be sure the burners and grates are cool before you
place your hand, a pot holder, cleaning cloths or
other materials on them.
How to Select Flame Size
Watch the flame, not the knob, as you reduce heat.
The flame size on a gas burner should match the
cookware you are using.
FOR SAFE HANDLING OF COOKWARE NEVER
LET THE FLAME EXTEND UP THE SIDES OF
THE COOKWARE.
Any flame larger than the bottom of the cookware is
wasted and only serves to heat the handle.
(continued next page)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SURFACE COOKING
(continued)
Top-of-Range Cookware
Aluminum: Medium-weight cookware is
recommended because it heats quickly and evenly.
Most foods brown evenly in an aluminum skillet.
Use saucepans with tight-fitting lids when cooking
with minimum amounts of water.
Glass: There are two types of glass cookware—those
for oven use only and those for top-of-range cooking
(saucepans, coffee and teapots). Glass conducts heat
very slowly.
Heatproof Glass Ceramic: Can be used for either
surface or oven cooking. It conducts heat very slowly
and cools very slowly. Check cookware manufacturer’s
directions to be sure it can be used on gas ranges.
Cast-Iron: If heated slowly, most skillets will give
satisfactory results.
Enamelware: Under some conditions, the enamel of
some cookware may melt. Follow cookware
manufacturer’s recommendations for cooking methods.
Stainless Steel: This metal alone has poor heating
properties and is usually combined with copper,
aluminum or other metals for improved heat
distribution. Combination metal skillets usually work
satisfactorily if they are used with medium heat as the
manufacturer recommends.
Stove Top Grills (on models with sealed burners)
Wok This Way (on models with sealed burners)
Do not use stove top grills
on your sealed gas burners.
If you use the stove top
grill on the sealed gas
We recommend that you
use a flat-bottomed wok.
They are available at your
local retail store.
burner it will cause
A traditional round bottom wok can be used with Wok
Holder accessory, model JXWK which can be ordered
from your appliance dealer. The Wok Holder fits on
top of the range grate to provide support and proper
air circulation for traditional round bottom woks only.
Do not use flat bottomed woks with the Wok Holder.
incomplete combustion and
can result in exposure to
carbon monoxide levels
above allowable current
standards. This can be
hazardous to your health.
Do not use a wok on any
other support ring.
Placing the ring over the
burner grate may cause the
burner to work improperly,
resulting in carbon
monoxide levels above
allowable current standards. This could be dangerous
to your health. Do not try to use such woks without
the ring unless you are using the Wok Holder. You
could be seriously burned if the wok tipped over.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES OF YOUR OVEN CONTROLS
OVEN SET Control Knob
The OVEN SET control knob has settings for
BAKE, BROIL, TIME BAKE and CLEAN.
When you turn the knob to the desired setting,
the proper burner is activated for that operation.
OVEN SET
BAKE—Use this setting for all normal oven
operations—for example, for cooking roasts or
casseroles. Only the bottom oven burner operates
during baking.
E
BROIL—Use this setting for broiling. Only the top
(broil) burner will operate.
TIME BAKE—Use this setting to turn the oven on
and off at specified times when you want cooking to
start and stop.
CLEAN—Use this setting for the self-cleaning
function only. See the Operating the Self-Cleaning
Oven section.
OVEN TEMP Control Knob
The OVEN TEMP control maintains the
temperature you set for normal oven operation
as well as for broiling. Push in and turn to set the
temperature or to set to the CLEAN position.
OVEN TEMP
OFF—Shuts off power to the oven controls. The oven
will not operate. The OVEN TEMP knob should be
turned to OFF whenever the oven is not in use.
5
For normal oven operation, push in and turn the
knob to the desired temperature. It will normally take
30-90 seconds before the flame comes on
After the oven reaches the selected temperature,
the oven burner cycles—off completely, then on with
a full flame—to keep the oven temperature controlled.
The OVEN CYCLE light will cycle on and off with
the burner.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES OF YOUR OVEN CONTROLS,
CLOCK AND TIMER
Clock and Timer with Press Pads
(on some models)
4. UP. Short taps to this pad increase the time by
small amounts. Press and hold the pad to increase
the time by larger amounts.
1
2
4
3
COOK
TIME
5
CLOCK
5. OVEN CYCLE light. Cycles on and off with the
ON/OFF
burner(s) to maintain the oven temperature.
START
TIME
OVEN
CYCLE
TIMER
ON/OFF
ON/OFF
6. DOWN. Short taps to this pad decrease the
time by small amounts. Press and hold the pad
to decrease the time by larger amounts.
8
7
6
1. CLOCK. Press this pad before setting the
7. START TIME ON/OFF. Press this pad to delay
the starting of your oven up to 11 hours and 59
minutes. Use the UP and DOWN pads to set the
desired start time.
clock. To set the clock, first press the CLOCK
pad. Then press the UP or DOWN pads to change
the time of day.
2. COOK TIME ON/OFF. Turn the OVEN SET
knob to TIME BAKE and the OVEN TEMP knob
to the desired cooking temperature. Press the
COOK TIME ON/OFF pad and then press the UP
or DOWN pads to set the amount of time you want
your food to cook. The oven will shut off after
Cook Time has run out.
8. TIMER ON/OFF. Press this pad to select the
timer feature. The timer does not control oven
operations. The timer can be set for 24 hours.
To set the timer, first press the TIMER ON/OFF
pad. Press the UP and DOWN pads to set the
amount of time you want.
To cancel the timer, press the TIMER ON/OFF pad.
3. DISPLAY. Shows the time of day, the times set
for the timer, the times set for the automatic oven
operations and clean cycle.
Clock (on models with press pads)
To Set the Clock (on models with press pads)
1. Press the CLOCK pad.
The clock must be set for the automatic oven timing
functions to work properly. The time of day cannot
be changed during a Timed Baking or a Self-Cleaning
cycle.
2. Press the UP or DOWN pad
CLOCK
to set the time of day.
3. Press the CLOCK pad to start.
Timer (on models with press pads)
The timer is a minute timer only; it does not control
oven operations. The maximum setting on the timer
is 24 hours.
To Set the Timer (on models with press pads)
1. Press the TIMER ON/OFF pad.
TIMER
2. Press the UP or DOWN pad to set the
ON/OFF
amount of time on the timer.
To set the timer one minute at a time, tap the pads.
To set the timer ten minutes at a time press and
hold the pad.
The timer will start automatically within a few
seconds of releasing the UP or DOWN pad.
To Reset the Timer (on models with press pads)
To Cancel the Timer (on models with press pads)
Press the UP or DOWN pad until the desired
time is set.
Press the TIMER ON/OFF pad until the time
remaining is cleared.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Outage (on models with press pads)
End of Cycle Tones (on models with press pads)
When power is restored, you will need to reset
the clock.
The end of cycle tone is a series of three beeps.
Reminder beeps continue until the oven is turned off.
All other functions that were in operation when the
power went out will have to be programmed again.
Clock and Minute Timer with Dials (on some models)
To set the clock, push the knob
Minutes are marked up to 60 on the center
ring of the clock.
12
in and turn the clock hands to
OFF
the correct time. Then let the
knob out and continue turning
to OFF.
60
0
To set the minute timer, turn the knob to the left,
without pushing in, until the pointer reaches the number
of minutes you want to time.
50
40
10
20
9
3
30
At the end of the set time, a buzzer sounds to tell
you time is up. Turn the knob, without pushing in,
until the pointer reaches OFF and the buzzer stops.
6
The minute timer has been combined with the range
clock. Use it to time cooking operations. You’ll
recognize it as the pointer that is different in color
from the clock hands.
Automatic Oven Timers with Dials (on some models)
These timers will
automatically start and
stop your oven for you.
STOP TIME DELAY START
NOTE: There must be at least a half-hour difference
between the DELAY START and STOP TIME dials,
and times can be set only up to 11 hours and 45
minutes in advance.
12
6
12
6
9
3
9
3
4. Set the OVEN SET knob to TIME BAKE (or
PUSH TO TURN
CLEAN).
Here’s what you do:
5. Set the OVEN TEMP knob to the desired cooking
1. Make sure both your range clock and the DELAY
START dial show the correct time of day. When
either the DELAY START dial or STOP TIME dial
is pushed in and turned, it will “pop” into place
when the time shown on the range clock is reached.
temperature (or CLEAN).
The oven will turn itself on immediately unless you
have set the DELAY START dial for a later starting
time. It will operate at the temperature you selected
and turn itself off at the Stop Time you selected.
2. Set the DELAY START dial. Push in and turn the
DELAY START dial to the time you want the oven
to turn itself on. (If you want it to start cooking
immediately, do not set DELAY START time.)
Turn the OVEN TEMP knob to OFF and then take
your food out of the oven.
3. Set the STOP TIME dial. Push in and turn the
STOP TIME dial to the time you want the oven to
turn itself off.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
USING YOUR OVEN
Before Using Your Oven
Be sure you understand how to set the controls
properly. Practice removing and replacing the shelves
while the oven is cool. Read the information and tips
on the following pages. Keep this guide handy where
you can refer to it, especially during the first weeks of
using your new range.
Electric Ignition
The oven burner and broil burner are lighted by
electric ignition.
Power Outage
To light either burner, turn the OVEN SET knob to
the desired oven operation and the OVEN TEMP
knob to the desired temperature. The burner should
ignite within 30-90 seconds.
CAUTION: Do not make any attempt to operate
the electric ignition oven during an electrical
power failure.
The oven or broiler cannot be lit during a power
failure. Gas will not flow unless the glow bar is hot.
After the oven reaches the selected temperature, the
oven burner cycles—off completely, then on with a
full flame—to keep the oven temperature controlled.
If the oven is in use when a power failure occurs,
the oven burner shuts off and cannot be re-lit until
power is restored.
Oven Light
Use the switch on the control panel to turn the oven light on or off.
Oven Moisture
As your oven heats up, the temperature change of the
air in the oven may cause water droplets to form on the
door glass. These droplets are harmless and will
evaporate as the oven continues to heat up.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Oven Vents
The oven is vented through duct openings at the rear
of the cooktop. See the Features section. Do not block
these openings when cooking in the oven—it is
important that the flow of hot air from the oven and
fresh air to the oven burners be uninterrupted.
• Handles of pots and pans on the cooktop may
become hot if left too close to the vent.
• Metal items will become very hot if they are left
on the cooktop and could cause burns.
• Do not leave any items on the cooktop. The hot air
from the vent may ignite flammable items and will
increase pressure in closed containers, which may
cause them to burst.
• The vent openings and
nearby surfaces may
become hot. Do not
touch them.
• Do not leave plastic
Vent appearance and location vary
items on the cooktop—
they may melt if left too
close to the vent.
Oven Shelves
Bump
The shelves are designed with stop-locks so when
placed correctly on the shelf supports, they will
stop before coming completely out of the oven and
will not tilt when you are removing food from them
or placing food on them.
When placing cookware on a shelf, pull the shelf out
to the bump on the shelf support. Place the cookware
on the shelf, then slide the shelf back into the oven.
This will eliminate reaching into the hot oven.
To remove a shelf from the oven, pull it toward you,
tilt the front end upward and pull the shelf out.
To replace, place the shelf on the shelf support with
the stop-locks (curved extension of the shelf) facing
up and toward the rear of the oven. Tilt up the front
and push the shelf toward the back of the oven until it
goes past the bump on the shelf support. Then lower
the front of the shelf and push it all the way back.
Shelf Positions
The oven has five shelf supports for baking,
roasting and broiling identified in this illustration
as A (bottom), B, C, D and E (top). It also has a
special low shelf position (R) for roasting extra
large items, such as a large turkey—the shelf is not
designed to slide out at this position. Shelf positions
for cooking are suggested in the Baking, Roasting
and Broiling sections.
E
D
C
B
A
R
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BAKING
Do not lock the oven door with the latch during
baking. The latch is used for self-cleaning only.
If you think an adjustment is necessary, see the Adjust
the Oven Thermostat section. It gives easy Do It
Yourself instructions on how to adjust the thermostat.
Your oven temperature is controlled very accurately
using an oven control system. It is recommended that
you operate the oven for a number of weeks to
become familiar with your new oven’s performance.
How to Set Your Range for Baking
To avoid possible burns, place the shelves in the
correct position before you turn the oven on.
2. Check the food for doneness at the minimum time
on the recipe. Cook longer if necessary.
1. Close the oven door. Turn the OVEN SET knob to
BAKE and then turn the OVEN TEMP knob to the
desired temperature.
3. Turn the OVEN TEMP knob to OFF and
then remove the food.
Oven Shelves
Arrange the oven
shelf or shelves in
Type of Food
Angel food cake
Biscuits or muffins
Cookies or cupcakes
Brownies
Shelf Position
A
E
the desired
D
locations while
B or C
the oven is cool.
C
B
The correct shelf
B or C
position depends
A
R
on the kind of
food and the
B or C
Layer cakes
B or C
browning desired.
As a general rule,
place most foods in the middle of the oven, on
either shelf position B or C. See the chart for
suggested shelf positions.
Bundt or pound cakes
Pies or pie shells
Frozen pies
A or B
B or C
A (on cookie sheet)
B or C
Casseroles
Roasting
B or R
Preheating
Pan Placement
Preheat the oven if the recipe calls for it. Preheat
means bringing the oven up to the specified
temperature before putting the food in the oven.
To preheat, set the oven at the correct temperature—
selecting a higher temperature does not shorten
preheat time.
For even cooking and proper browning, there must be
enough room for air circulation in the oven. Baking
results will be better if baking pans are centered as
much as possible rather than being placed to the front
or to the back of the oven.
Pans should not touch each other or the walls of the
1
2
Preheating is necessary for good results when baking
cakes, cookies, pastry and breads. For most casseroles
and roasts, preheating is not necessary. For ovens
without a preheat indicator light or tone, preheat 10
minutes. After the oven is preheated place the food
in the oven as quickly as possible to prevent heat
from escaping.
oven. Allow 1– to 1 ⁄ –inch space between pans as
well as from the back of the oven, the door and the
sides. If you need to use two shelves, stagger the pans
so one is not directly above the other.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Baking Guides
When using prepared baking mixes, follow package recipe or
instructions for best baking results.
Cookies
Aluminum Foil
When baking cookies,
flat cookie sheets
Never entirely cover
a shelf with aluminum
foil. This will disturb
the heat circulation and
result in poor baking. A
smaller sheet of foil
may be used to catch a
spillover by placing it
on a lower shelf several
inches below the food.
(without sides)
produce better-looking
cookies. Cookies
baked in a jelly roll
pan (short sides all
around) may have
darker edges and pale
or light browning may occur.
Do not use a cookie sheet so large that it touches
the walls or the door of the oven.
For best results, use only one cookie sheet in the oven
at a time.
Pies
Cakes
For best results, bake pies in dark, rough or dull pans
to produce a browner, crisper crust. Frozen pies in foil
pans should be placed on an aluminum cookie sheet
for baking since the shiny foil pan reflects heat away
from the pie crust; the cookie sheet helps retain it.
When baking cakes, warped or bent pans will cause
uneven baking results and poorly shaped products.
A cake baked in a pan larger than the recipe
recommends will usually be crisper, thinner and drier
than it should be. If baked in a pan smaller than
recommended, it may be undercooked and batter may
overflow. Check the recipe to make sure the pan size
used is the one recommended.
Baking Pans
Don’t Peek
Use the proper baking pan. The type of finish on
the pan determines the amount of browning that
will occur.
Set the timer for the estimated cooking time and do
not open the door to look at your food. Most recipes
provide minimum and maximum baking times such
as “bake 30-40 minutes.”
• Dark, rough or dull pans absorb heat resulting in a
browner, crisper crust. Use this type for pies.
DO NOT open the door to check until the minimum
time. Opening the oven door frequently during
cooking allows heat to escape and makes baking times
longer. Your baking results may also be affected.
• Shiny, bright and smooth pans reflect heat, resulting
in a lighter, more delicate browning. Cakes and
cookies require this type of pan.
• Glass baking dishes also absorb heat. When baking
in glass baking dishes, the temperature may need to
be reduced by 25°F.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TIMED BAKING
Automatic Oven Timer (on models with press pads)
For models with DELAY START and STOP TIME dials, see the
Automatic Oven Timers section in Oven Controls, Clock and Timer.
How to Time Bake
Do not lock the oven door with the latch during
regular timed baking. The latch is used for self-
To set the clock, first press the
CLOCK pad. Press the UP or DOWN pad
until correct time of day is displayed. Press
the CLOCK pad again to start.
CLOCK
cleaning only.
Your oven can be set to turn on and off automatically.
NOTE: Before beginning, make sure the oven clock
shows the correct time of day.
How to Set Immediate Start and Automatic Stop
To avoid possible burns, place the shelves in the
5. The oven will turn on. The display will show the
Cook Time remaining. When the oven reaches the
set temperature, a tone sounds. The oven will
continue to cook for the programmed amount of
time up to 11 hours and 50 minutes, then shut off
automatically.
correct position before you turn the oven on.
The oven will turn on immediately and cook for a
selected length of time. At the end of Cook Time the
oven will turn off automatically.
OVEN TEMP
OVEN SET
6. When the oven automatically turns off, the oven
control will signal. Turn the oven off to stop the
signal.
7. Remove the food from the oven. Remember,
foods that are left in the oven continue cooking
after the controls are off.
A
NOTE: Foods that spoil easily such as milk, eggs,
fish, stuffings, poultry and pork should not be allowed
to sit for more than one hour before or after cooking.
Room temperature promotes the growth of harmful
bacteria. Be sure that oven light is off because heat
from the bulb will speed harmful bacteria growth.
1. Turn the OVEN SET knob to TIME BAKE.
2. Turn the OVEN TEMP knob to the desired
temperature.
3. Press the COOK TIME ON/OFF pad.
COOK
TIME
ON/OFF
4. Set the desired amount of cooking time
using the UP and DOWN pads.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Set Delay Start and Automatic Stop
4. For 3 hours of cooking time,
press the UP pad until “3:00”
appears in the display.
Quick Reminder
1. Turn the OVEN SET knob to TIME BAKE.
2. Turn the OVEN TEMP knob to the
5. Press the START TIME ON/OFF pad.
desired temperature.
START
TIME
3. Press the COOK TIME ON/OFF pad.
ON/OFF
4. Press the UP or DOWN pad to set the
desired length of cooking time.
6. Press the UP pad until “4:00” appears in the
display. The timer is now set to start baking in
2 hours, at 4:00.
5. Press the START TIME ON/OFF pad.
6. Press the UP or DOWN pad to set the
time of day you want cooking to start.
Once the oven begins cooking, the Cook Time
remaining will be displayed.
To avoid possible burns, place the shelves in the
correct position before you program the oven.
At the end of the 3 hour cooking time (7:00),
the oven will automatically turn off.
You can set the oven control to turn the oven on
automatically, cook for a specific length of time and
turn off automatically.
7. When the oven automatically turns off, the oven
control will signal. Turn the OVEN TEMP knob
to OFF to stop the signal. Remove the food from
the oven. Remember, even though the oven shuts
off automatically, foods continue cooking after the
controls are off.
For example: Let’s say it’s 2:00 and dinner time is
shortly after 7:00. The recipe suggests 3 hours baking
time at 325°F. Here’s how:
NOTE:
OVEN TEMP
OVEN SET
• The low temperature zone of this range (between
150°F and 200°F) is available to keep hot cooked
foods warm. Food kept in the oven longer than two
hours at these low temperatures may spoil.
• Foods that spoil easily such as milk, eggs, fish,
stuffings, poultry and pork should not be allowed
to sit out for more than one hour before or after
cooking. Room temperature promotes the growth
of harmful bacteria. Be sure the oven light is off
because heat from the bulb will speed harmful
bacteria growth.
A
1. Turn the OVEN SET knob to TIME BAKE.
2. Turn the OVEN TEMP knob to the desired
temperature (in this example 325°F).
3. Press the COOK TIME ON/OFF pad.
COOK
TIME
ON/OFF
Questions and Answers
Q. Can I use the minute timer during oven
cooking?
Q. Can I change the time of day on the clock while
I’m Time Baking in the oven?
A. The minute timer can be used during any
A. The time of day on the clock should not be
changed during any program that uses the oven
timer. You must either stop those programs or wait
until they are finished before changing the time.
cooking function.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUST THE OVEN THERMOSTAT—
DO IT YOURSELF!
You may feel that your new oven cooks differently
To Adjust the Thermostat:
than the one it replaced. We recommend that you
use your new oven for a few weeks to become more
familiar with it, following the times given in your
recipes as a guide.
Note the position of the pointer to the screw
before making the adjustment.
If you think your new oven is too hot or too cold,
you can adjust the thermostat yourself. If you think
it is too hot, adjust the thermostat to make it cooler.
If you think it is too cool, adjust the thermostat to
make it hotter.
We do not recommend the use of inexpensive
thermometers, such as those found in grocery stores,
to check the temperature setting of your new oven.
These thermometers may vary 20–40 degrees.
Cooler
Hotter
(appearance may vary)
Pull the OVEN TEMP knob off the range and look
at the back side.
OVEN TEMP
To make adjustment, loosen (approximately one turn),
but do not completely remove, the two screws on the
back of the knob. With the back of the knob facing
you, hold the outer edge of the knob with one hand
and turn the front of the knob with the other hand.
5
To raise the oven temperature, move the top screw
toward the right. You’ll hear a click for each notch
you move the knob. To lower the temperature, move
the top screw toward the left. Each click will change
the oven temperature approximately 10°F. (Range is
plus or minus 60°F. from the arrow.)
Front of the OVEN TEMP knob
We suggest that you make the adjustment one click
from the original setting and check oven performance
before making any additional adjustments.
After the adjustment is made, retighten the
screws so they are snug, but be careful not to
overtighten. Reinstall the knob on the range
and check performance.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
ROASTING
Do not lock the oven door with the latch during
Roasting is really a baking procedure used for meats.
Therefore the oven controls are set for Baking or
Timed Baking. (You may hear a slight clicking sound
indicating the oven is working properly.) Timed
Baking will turn the oven on and off automatically.
roasting. The latch is used for self-cleaning only.
Roasting is cooking by dry heat. Tender meat or
poultry can be roasted uncovered in your oven.
Roasting temperatures, which should be low and
steady, keep spattering to a minimum.
Most meats continue to cook slightly while standing
after being removed from the oven. Recommended
standing time for roasts is 10 to 20 minutes. This
allows roasts to firm up and makes them easier to
carve. The internal temperature will rise about 5° to
10°F. If you wish to compensate for the temperature
rise, remove the roast from the oven when its internal
temperature is 5° to 10°F. less than the temperature
shown in the Roasting Guide.
The oven has a special
low shelf (R) position
just above the oven
bottom. Use it when
extra cooking space is
needed, for example,
when roasting a large
turkey. The shelf is not
designed to slide out at
this position.
R
Remember that food will continue to cook in the hot
oven and therefore should be removed when the
desired internal temperature has been reached.
1. Position the oven
at shelf (B) position
for small size roast
(3 to 5 lbs.) and at
(R) position for
3. Turn the OVEN SET knob to BAKE and the
OVEN TEMP knob to the desired temperature.
See the Roasting Guide for temperatures and
approximate cooking times.
B
4. When roasting is finished, turn the OVEN
TEMP knob to OFF and then remove the food
from the oven.
A
larger roasts.
R
2. Check the weight of the roast. Place the meat
fat-side-up or the poultry breast-side-up on the
roasting grid in a shallow pan. The melting fat will
baste the meat. Select a pan as close to the size of
meat as possible. (The broiler pan with grid is a
good pan for this.)
Dual Shelf Cooking
Use of Aluminum Foil
This allows more than one food to be cooked at the
same time. For example: While roasting a 20-lb.
turkey on shelf position R, a second shelf (if so
equipped) may be added on position D so that
scalloped potatoes can be cooked at the same time.
Calculate the total cooking time to enable both dishes
to complete cooking at the same time. Allow 15-20
minutes of additional cooking time for the potatoes.
You can use aluminum foil to line the broiler pan.
This makes clean-up easier when using the pan for
marinating, cooking with fruits, cooking heavily
cured meats or basting food during cooking. Press
the foil tightly around the inside of the pan.
(continued next page)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ROASTING
(continued)
Questions and Answers
Q. Is it necessary to check for doneness with a
meat thermometer?
Q. Do I need to preheat my oven each time I cook
a roast or poultry?
A. Checking the finished internal temperature at the
completion of cooking time is recommended.
Temperatures are shown in Roasting Guide. For
roasts over 8 lbs., check with thermometer at half-
hour intervals after half the time has passed.
A. It is not necessary to preheat your oven.
Q. When buying a roast, are there any special tips
that would help me cook it more evenly?
A. Yes. Buy a roast as even in thickness as possible,
or buy rolled roasts.
Q. Why is my roast crumbling when I try to
carve it?
Q. Can I seal the sides of my foil “tent” when
roasting a turkey?
A. Roasts are easier to slice if allowed to cool 10 to
20 minutes after removing from oven. Be sure to
cut across the grain of the meat.
A. Sealing the foil will steam the meat. Leaving
it unsealed allows the air to circulate and brown
the meat.
ROASTING GUIDE
Frozen Roasts
Frozen roasts of beef, pork, lamb, etc., can be started
without thawing, but allow 15 to 25 minutes per pound
additional time (15 minutes per pound for roasts under
5 pounds, more time for larger roasts.)
Make sure poultry is thawed before roasting.
Unthawed poultry often does not cook evenly.
Some commercial frozen poultry can be cooked
successfully without thawing. Follow directions
given on package label.
Oven
Approximate Roasting Time
in Minutes per Pound
Internal
Temperature °F.
Type
Temperature Doneness
Meat
3 to 5 lbs.
24–35
35–39
39–45
21–25
25–30
30–35
35–45
35–45
6 to 8 lbs.
Tender cuts; rib, high quality sirloin
tip, rump or top round*
325°
325°
Rare:
18–25
25–31
31–33
20–23
24–28
28–33
30–40
30–40
140°–150°†
150°–160°
170°–185°
140°–150°†
150°–160°
170°–185°
170°–180°
170°–180°
115°–125°
Medium:
Well Done:
Rare:
Lamb leg or bone-in shoulder*
Medium:
Well Done:
Well Done:
Well Done:
To Warm:
Veal shoulder, leg or loin*
Pork loin, rib or shoulder*
Ham, precooked
325°
325°
325°
18–23 minutes per pound (any weight)
Poultry
3 to 5 lbs.
35–40
Over 5 lbs.
Chicken or Duck
Chicken pieces
325°
350°
Well Done:
Well Done:
30–35
185°–190°
185°–190°
In thigh:
35–40
10 to 15 lbs.
16–22
Over 15 lbs.
12–19
Turkey
325°
Well Done:
185°–190°
*For boneless rolled roasts over 6 inches thick, add 5 to 10 minutes per pound to times given above.
†The U.S. Department of Agriculture says “Rare beef is popular, but you should know that cooking it to only 140°F. means
some food poisoning organisms may survive.” (Source: Safe Food Book. Your Kitchen Guide. USDA Rev. June 1985.)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
BROILING
Do not lock the oven door with the latch during
Turn the food only once
during cooking. Time the
foods for the first side
according to the Broiling
Guide.
broiling. The latch is used for self-cleaning only.
Broiling is cooking food by direct heat from above the
food. Most fish and tender cuts of meat can be
broiled. Follow these directions to keep spattering and
smoking to a minimum.
Turn the food, then use
the times given for the
second side as a guide to
the preferred doneness.
The oven door should be closed during broiling.
1. If the meat has fat or gristle around the edge, cut
vertical slashes through both about 2″ apart. If
desired, the fat may be trimmed, leaving a layer
about 1/8″ thick.
4. Close the oven door but do not latch it. If the door
latch is moved to the right during a broil
operation the door may lock and you may not be
able to open it until the oven cools.
2. Place the meat on the broiler grid in the broiler pan
which comes with the range. Always use the grid
so fat drips into the broiler pan; otherwise the juices
may become hot enough to catch fire.
5. Turn the OVEN SET knob and the OVEN TEMP
knob to BROIL.
6. When broiling is finished, turn OVEN TEMP knob
to OFF. Remove the broiler pan from the range and
serve food immediately. Leave the pan outside the
range to cool.
3. Position the shelf on the recommended shelf
position as suggested in Broiling Guide.
Use of Aluminum Foil
You can use aluminum foil to line your broiler pan and
broiler grid. However, you must mold the foil tightly
to the grid and cut slits in it just like the grid.
Without the slits, the foil will prevent fat and meat
juices from draining to the broiler pan. The juices
could become hot enough to catch on fire. If you do
not cut the slits, you are frying, not broiling.
Questions and Answers
Q. When broiling, is it necessary to always use a
grid in the pan?
Q. Why are my meats not turning out as brown as
they should?
A. Yes. Using the grid suspends the meat over the
pan. As the meat cooks, the juices fall into the pan,
thus keeping meat drier. Juices are protected by the
grid and stay cooler, thus preventing excessive
spatter and smoking.
A. Check to see if you are using the recommended
shelf position. Broil for the longest period of time
indicated in the Broiling Guide. Turn the food only
once during broiling.
(continued next page)
Q. Should I salt the meat before broiling?
A. No. Salt draws out the juices and allows them to
evaporate. Always salt after cooking. Turn the
meat with tongs; piercing the meat with a fork also
allows juices to escape. When broiling poultry or
fish, brush each side often with butter.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
BROILING GUIDE
The oven door must be closed during broiling.
• If desired, marinate meats or chicken before broiling.
Or brush with barbecue sauce last 5 to 10 minutes only.
• Always use the broiler pan and grid that comes with
your range. It is designed to minimize smoking and
spattering by trapping juices in the shielded lower
part of the pan.
• When arranging food on the pan, do not let fatty
edges hang over the sides because dripping fat could
soil the oven.
• For steaks and chops, slash the fat evenly around the
outside edges of the meat. To slash, cut crosswise
through the outer fat surface just to the edge of the
meat. Use tongs to turn the meat over to prevent
piercing the meat and losing the juices.
• The broiler compartment does not need to be
preheated. However, for very thin foods, or to
increase browning, preheat if desired.
• Frozen steaks can be broiled by positioning the shelf
at next lowest shelf position and increasing cooking
1
2
time given in this guide 1 ⁄ times per side.
Quantity and/or
Thickness
Shelf 1st Side 2nd Side
Position Minutes Minutes Comments
Food
1
2
Bacon
1/2 lb. (about 8
thin slices)
C
3 ⁄
3
Arrange in single layer.
Ground Beef
1 lb. (4 patties)
1/2 to 3/4 inch thick
C
10–11
4–5
Space evenly. Up to 8 patties take
about same time.
Beef Steaks
Rare
Medium
Well Done
1 inch thick
B
B
B
9
12
13
7
5–6
8–9
Steaks less than 1 inch thick cook
through before browning. Pan frying
is recommended.
1
2
(1 to 1 ⁄ lbs.)
Rare
Medium
Well Done
1 inch thick
B
B
B
10
12–15
25
6–7
10–12
16–18
Slash fat.
1
2
(2 to 2 ⁄ lbs.)
Chicken
1 whole
B
30–35
25–30
Reduce times about 5 to 10 minutes per
side for cut-up chicken. Brush each side
with melted butter. Broil skin-side-down first.
1
2
(2 to 2 ⁄ lbs.),
split lengthwise
Bakery Products
Bread (Toast) or
Toaster Pastries
English Muffins
2 to 4 slices
1 pkg. (2)
2, split
C
2–3
1/2–1
Space evenly. Place English muffins cut-
side-up and brush with butter if desired.
C
C
3–5
Lobster Tails
2 to 4
(6 to 8 oz. each)
13–16
Do not
Cut through back of shell and spread open.
turn over. Brush with melted butter before broiling and
after half of time.
Fish
1-lb. fillets
B
C
5
8
5
Handle and turn very carefully. Brush with lemon
butter before broiling and during broiling if
desired. Preheat broiler to increase browning.
1/4 to 1/2 inch thick
Ham Slices
Precooked
1 inch thick
8
Increase time 5 to 10 minutes per side
1
2
for 1 ⁄ inch thick or home cured.
Pork Chops
Well Done
2 (1/2 inch thick)
2 (1 inch thick),
about 1 lb.
B
B
10
13
4–5
9–12
Slash fat.
Lamb Chops
Medium
Well Done
Medium
Well Done
2 (1 inch thick),
B
B
B
B
8
4–7
10
Slash fat.
about 10 to 12 oz.
10
10
17
1
2
2 (1 ⁄ inch thick),
4–6
about 1 lb.
12–14
Wieners
similar precooked
sausages, bratwurst
1-lb. pkg. (10)
C
6
1–2
If desired, split sausages in half
lengthwise; cut into 5- to 6-inch pieces.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE SELF-CLEANING OVEN
Normal Cleaning Time: 3 hours
Before a Clean Cycle
We recommend venting with an open window
or using a ventilation fan or hood during the first
self-clean cycle.
3. Clean spatters or spills on the oven front frame,
and the oven door outside the gasket with a
dampened cloth. The oven front frame and the
oven door outside the gasket do not get cleaned by
the self-clean cycle. On these areas use detergent
and hot water or a soap-filled steel wool pad. Rinse
well with a vinegar and water solution. This will
help prevent a brown residue from forming when
the oven is heated. Buff these areas with a dry
cloth. Do not clean the gasket.
1. Remove the broiler pan, broiler grid, all cookware
and any aluminum foil from the oven—they cannot
withstand the high cleaning temperatures.
NOTE: Take the shelves out of the oven before
you begin the self-clean cycle.
2. Wipe up heavy soil on the oven bottom. If you
use soap, rinse thoroughly before self-cleaning
to prevent staining.
Clean the top, sides and outside front of the oven
door with soap and water. Do not use abrasives or
oven cleaners.
Make sure the oven light bulb cover is in place.
Do not rub or clean the door gasket—
the fiberglass material of the gasket has an
Oven
light
Oven
front
frame
extremely low resistance to abrasion. An intact
and well-fitting oven door gasket is essential for
energy-efficient oven operation and good baking
results. If you notice the gasket becoming worn,
frayed or damaged in any way or if it has become
displaced on the door, you should have it replaced.
4. Close the door and make sure the oven light is
off. If the oven light is not turned off, the life
of the bulb will be shortened or it may burn out
immediately.
CAUTION: The grates and drip pans
(on some models) should never be cleaned
in the self-cleaning oven.
Area
outside inside
gasket gasket
Area
Oven door
gasket
Do not use commercial oven cleaners or oven
protectors in or near the self-cleaning oven.
A combination of any of these products plus the high
clean cycle temperatures may damage the porcelain
finish of the oven.
(continued next page)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE SELF-CLEANING OVEN
(continued)
How to Set the Oven for Cleaning
1. Turn the OVEN SET knob and the OVEN TEMP
knob to CLEAN. The controls will snap into the final
position when the CLEAN location is reached.
3. When the clean cycle is complete, you will be able
to slide the door latch handle to the left as far as it
will go and open the door.
2. Slide the latch handle to the right as far as it will go.
Never force the door latch handle. If you cannot
slide the latch easily to unlock the door, allow
additional time for cooling.
Never force the door latch handle. Forcing the
handle may damage the door lock mechanism.
Turn the OVEN TEMP knob to OFF.
For models with press pads, the oven will now be
set to clean for its normal time of three hours. If you
wish to change the amount of cleaning time, see the
How to Set the Amount of Cleaning Time section.
For models with dials, see the How to Set the
Amount of Cleaning Time section.
How to Set the Amount of Cleaning Time
Models with press pads:
Decide on the cleaning hours necessary. The
recommended cleaning times are: Light to Moderate
Soil—2–3 hours (thin spills and light spatters), Heavy
Soil—4 hours (heavy, greasy spills and spatters).
The clean cycle is normally 3 hours. You can change
the clean time to any time between 2 and 4 hours
depending on the amount of soil in your oven.
Add these hours to the present time of day, then push
in and turn the STOP TIME dial clockwise to this
later stop time.
1. Turn the OVEN SET knob and the OVEN TEMP
knob to CLEAN. Slide the latch handle to the right
as far as it will go.
The oven door gets hot during self-cleaning. DO NOT
TOUCH. The CLEANING light will glow, indicating
the controls have been set correctly and the clean
cycle has begun. If a delayed start has been selected,
the CLEANING light will not glow until the start time
has been reached and the clean cycle begins. The door
will lock approximately 20 minutes after the clean
cycle has begun.
2. Press the UP or DOWN pad to set the desired
cleaning time.
You have one minute to change your clean time after
the normal cleaning time of 3 hours is displayed.
Models with dials:
Set the automatic oven timers: Make sure the range
clock is set to the correct time of day. Clear the
DELAY START and STOP TIME dials of any
previous timed cooking or cleaning function by: one
at a time, push the DELAY START and STOP TIME
dials in and turn the dials. Using a light touch,
continue turning the knob until it “pops” out. Both
dials should now be in the out position.
After a Clean Cycle
After a clean cycle, you may notice some white ash
in the oven. Just wipe it up with a damp cloth.
If the shelves have become hard to slide, wipe the
shelf supports with cooking oil.
If white spots remain, remove them with a soap-
filled steel wool pad. Be sure to rinse thoroughly
with a vinegar and water mixture. These deposits
are usually a salt residue that cannot be removed by
the clean cycle.
NOTE:
• While the oven is self-cleaning (on models with
press pads), you can press the CLOCK pad to
display the time of day. To return to the clean
countdown, press the COOK TIME ON/OFF pad.
If the oven is not clean after one cycle, the cycle
may be repeated.
• You cannot set the oven for cooking until the oven
is cool enough for the door to be unlatched.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Delay Start of Cleaning
Models with press pads:
Models with dials:
You have one minute to set a delayed start.
If you wish to start and stop cleaning at a later time
than shown on the clock, push in and turn the DELAY
START dial to the time you wish to start. Add the
hours needed for cleaning to this “start” time, then
push in and turn the STOP TIME dial to this later stop
time. The oven will automatically turn on and off at
the set times.
1. Turn the OVEN SET knob and the OVEN TEMP
knob to CLEAN. Slide the latch handle to the right
as far as it will go.
2. If you want to change the normal cleaning time,
press the UP or DOWN pad until the desired
amount of clean time is reached.
3. Press the START TIME ON/OFF pad.
4. Press the UP or DOWN pad to set the time of day
you want cleaning to start.
To Stop a Clean Cycle (all models)
Turn the OVEN TEMP knob to the OFF position. This will stop the
cleaning cycle but you will not be able to open the door until the oven
cools below the locking temperature.
Questions and Answers
Q. If my oven clock is not set to the correct time
of day, can I still self-clean my oven?
A. If the clock is not set to the correct time of day,
you will not be able to set a delay clean to end
at a specific time.
Q. Should there be any odor during the cleaning?
A. Yes, there will be a slight odor during the first few
cleanings. Failure to wipe out excessive soil might
also cause an odor when cleaning.
Q. What causes the hair-like lines on the enamel
surface of my oven?
A. This is a normal condition resulting from heating
and cooling during cleaning. They do not affect
how your oven performs.
Q. Can I use commercial oven cleaners on any part
of my self-cleaning oven?
A. No cleaners or coatings should be used around
any part of this oven. If you do use them and do
not thoroughly rinse the oven with water, wiping it
absolutely clean afterward, the residue can scar the
oven surface and damage metal parts the next time
the oven is automatically cleaned.
Q. Why do I have ash left in my oven after cleaning?
A. Some types of soil will leave a deposit, which is
ash. It can be removed with a damp sponge or cloth.
Q. My oven shelves do not slide easily. What is
the matter?
A. After many cleanings, the oven shelves will lose
their luster and become hard to slide. To make the
shelves slide more easily, wipe the shelf supports
with cooking oil.
Q. Can I clean the woven gasket around the oven door?
A. No, this gasket is essential for a good oven seal,
and care must be taken not to rub, damage or move
this gasket.
Q. What should I do if excessive smoking occurs
during cleaning?
A. This is caused by excessive soil, and you should
turn the OVEN TEMP knob to OFF. Open the
windows to rid the room of smoke. Allow the oven
to cool for at least one hour before opening the door.
Wipe up the excess soil and reset the clean cycle.
Q. My oven shelves have become gray after the
self-cleaning cycle. Is this normal?
A. Yes. After the self-cleaning cycle, the shelves will
have lost some luster and discolor to a deep gray.
Q. Can I cook food on the cooktop while the oven
is self-cleaning?
A. Yes. While the oven is self-cleaning, you can use
the cooktop just as you normally do. However, be
careful when standing in front of the range—oven
becomes very hot while self-cleaning.
Q. Is the ‘‘crackling’’ or “popping” sound I hear
during cleaning normal?
A. Yes. This is the metal heating and cooling during
both the cooking and cleaning functions.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND CLEANING
Proper care and cleaning are important so your range
BE SURE ELECTRICAL POWER IS
DISCONNECTED BEFORE CLEANING ANY
PART OF YOUR RANGE.
will give you efficient and satisfactory service. Follow
these directions carefully in caring for it to help assure
safe and proper maintenance.
CAUTION: DO NOT OPERATE THE BURNER WITHOUT ALL BURNER PARTS AND DRIP PANS
(IF SO EQUIPPED) IN PLACE.
Sealed Burner Assemblies (on some models)
Burner Heads (on sealed burners only)
Grate
Burner Cap
Drip Pan
(on some models)
Burner Head
Electrode
For proper ignition, make sure the small hole in
the section that fits over the electrode is kept open. A
sewing needle or wire twist-tie works well to unclog it.
The slits in the burner heads of your range
must be kept clean at all times for an even,
unhampered flame.
Turn all controls OFF before removing the
burner parts and drip pans (if so equipped).
You should clean the surface burners routinely,
especially after bad spillovers, which could clog
these openings.
The burner grates, caps, burner heads and drip
pans (if so equipped) can be lifted off, making them
easy to clean.
To remove burned-on food, soak the burner heads
in a solution of mild liquid detergent and hot water
for 20-30 minutes. For more stubborn stains, use a
toothbrush.
The electrode of
Electrode
the spark igniter is
exposed when the
burner head is
removed. When one
Before putting the burner head back, shake out
excess water and then dry it thoroughly by setting
it in a warm oven for 30 minutes.
burner is turned to LITE, all the burners spark.
Do not attempt to disassemble or clean around
any burner while another burner is on. An electric
shock may result, which could cause you to knock
over hot cookware.
Replace the burner caps. Make sure that caps are
replaced on the correct size burner. There is one
small, 2 medium and one large cap.
Burner Caps (on sealed burners only)
Lift off when cool. Wash burner caps
in hot, soapy water and rinse with
small
medium
medium
small
large
clean water. You may scour with a
plastic scouring pad to remove
burned-on food particles.
medium
large
Dry them in a warm oven or with a
cloth—don’t reassemble them wet.
Replace the burner caps.
Front of Range
Make sure that caps are replaced on
the correct size burner. There is one
small, 2 medium and one large cap.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: DO NOT OPERATE THE BURNER WITHOUT ALL BURNER PARTS AND DRIP PANS
(IF SO EQUIPPED) IN PLACE.
Standard Twin Burners (on some models)
The holes in the surface
burners of your range
Grate
must be kept clean at all
times for proper ignition
and an even,
unhampered flame.
Drip Pan
You should clean the
(on some models)
surface burners
Surface Burner
routinely, especially
Clean these
after bad spillovers,
which could clog these
holes. Wipe off surface
burners. If heavy
holes
thoroughly
on each
burner.
On models with standard twin burners, the cooktop
lifts up for easy access.
spillover occurs, remove the surface burners from
the range. Burners lift out for cleaning. Lift up the
cooktop and then lift out the surface burners.
Turn all controls OFF before removing burner
parts and drip pans (if so equipped).
The burner grates and drip pans (if so equipped)
can be lifted off, making them easy to clean.
To remove burned-on food, soak the surface burner
in a solution of mild liquid detergent and hot water.
Soak the surface burner for 20 to 30 minutes. For
more stubborn stains, use a cleanser like Soft Scrub®
brand or Bon Ami® brand. Rinse well to remove any
traces of the cleanser that might clog the surface
burner openings. Do not use steel wool because it
will clog the surface burner openings and scratch the
surface burners. If the holes become clogged, clean
them with a sewing needle or twist tie.
Before putting the surface burner back, shake out
excess water and then dry it thoroughly by setting it in
a warm oven for 30 minutes. Then place it back in the
range, making sure it is properly seated and level.
Check the flame pattern of each burner. If the flames
are “jumpy” (not steady), clean the holes again with a
sewing needle or twist tie.
Drip Pans (on some models)
Remove the grates and lift out the drip pans. Drip
pans can be cleaned in dishwasher or by hand.
To get rid of burned-on food, place them in a
covered container (or plastic bag) with 1/4 cup
ammonia to loosen the soil. Then scrub with a soap-
filled scouring pad if necessary.
When replacing the drip pans, make sure they are in
the correct position.
(continued next page)
CAUTION: Do not clean the drip pans in the self-
cleaning oven.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND CLEANING
(continued)
Burner Grates
Lift out when cool. Grates should be washed regularly
and, of course, after spillovers. Wash them in hot,
soapy water and rinse with clean water. After cleaning,
dry them thoroughly by putting them in a warm oven
for a few minutes. Don’t put the grates back on the
range while they are wet. When replacing the grates,
be sure they’re positioned securely over the burners.
Although they’re durable, the grates will gradually
lose their shine, regardless of the best care you can
give them. This is due to their continual exposure to
high temperatures.
To prevent rusting on cast iron grates, apply a light
coating of cooking oil on the bottom of the grates.
Do not operate a burner for an extended period of
time without cookware on the grate. The finish on
the grate may chip without cookware to absorb the heat.
To get rid of burned-on food, place the grates in a
covered container (or plastic bag) with 1/4 cup
ammonia to loosen the soil. Then scrub with a
soap-filled scouring pad if necessary.
CAUTION: Do not clean the grates in the
self-cleaning oven.
Cooktop Surface
To avoid damaging the porcelain enamel surface
of the cooktop and to prevent it from becoming
dull, clean up spills right away. Foods with a lot of
acid (tomatoes, sauerkraut, fruit juices, etc.) or foods
with high sugar content could cause a dull spot if
allowed to set.
When the surface has cooled, wash and rinse. For
other spills such as fat spatterings, etc., wash with
soap and water once the surface has cooled. Then
rinse and polish with a dry cloth.
Do not store flammable materials in an oven or
near the cooktop. Do not store or use combustible
materials, gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
Oven Bottom
The oven bottom has a porcelain enamel finish.
To make cleaning easier, protect the oven bottom
from excessive spillovers by placing a cookie sheet on
the shelf below the shelf you are cooking on. You can
use aluminum foil if you do not cover the whole shelf.
This is particularly important when baking a fruit pie
or other foods with a high acid content. Hot fruit
fillings or other foods that are highly acidic (such as
milk, tomatoes or sauerkraut, and sauces with vinegar
or lemon juice) may cause pitting and damage to the
porcelain enamel surface and should be wiped up
immediately. To clean up spillovers, use soap and
water, an abrasive cleaner or scouring pad. Rinse
well to remove any soap before self-cleaning.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Lift-Off Oven Door
The oven door is removable,
but it is heavy. You may need help
removing and replacing the door.
To remove the door, open it a few
inches to the special stop position
that will hold the door open. Grasp
firmly on each side and lift the door
straight up and off the hinges.
• Do not rub or clean the door gasket—the
fiberglass material of the gasket has an extremely
low resistance to abrasion. An intact and well-
fitting oven door gasket is essential for energy-
efficient oven operation and good baking results.
If you notice the gasket becoming worn, frayed or
damaged in any way or if it has become displaced
on the door, you should have it replaced.
NOTE: Be careful not to place
hands between the hinge and the
oven door frame as the hinge could snap back and
pinch fingers.
To replace the door, make sure the hinges are in the
special stop position. Position the slots in the bottom
of the door squarely over the hinges. Then lower the
door slowly and evenly over both hinges at the same
time. If the hinges snap back against the oven frame,
pull them back out.
TO CLEAN THE DOOR:
(Do not immerse the door in water.)
Inside of the door:
• Because the area inside the gasket is cleaned during
the self clean cycle, you do not need to clean this
by hand. Any soap left on the liner causes additional
stains when the oven is heated.
• The area outside the gasket can be cleaned with
a scouring pad.
Inside Gasket
Gasket
Outside Gasket
Outside of the door:
• Use soap and water to thoroughly clean the top,
sides and front of the oven door. Rinse well. You
may also use a glass cleaner to clean the glass on
the outside of the door.
• Spillage of marinades, fruit juices, tomato sauces
and basting materials containing acids may cause
discoloration and should be wiped up immediately.
When the surface is cool, clean and rinse.
• Do not use oven cleaners, cleansing powders or
harsh abrasives on the outside of the door.
Broiler Pan and Grid
After broiling, remove the
broiler pan from the oven.
Remove the grid from the
pan. Carefully pour out grease
from the pan into a proper
container. Wash and rinse the
broiler pan and grid in hot
water with a soap-filled or
plastic scouring pad.
If food has burned on, sprinkle the grid with detergent
while hot and cover with wet paper towels or a
dishcloth. Soaking the pan will remove burned on foods.
Both the broiler pan and grid can also be cleaned in
the dishwasher.
Do not store a soiled broiler pan and grid anywhere
in the range.
Do not clean the broiler pan or grid in the
self-cleaning oven.
Oven Shelves
Clean the shelves with
NOTE: Take the shelves out of the oven before you
begin the self-clean cycle.
an abrasive cleanser or
steel wool. After cleaning,
rinse the shelves with clean
water and dry with a clean cloth.
(continued next page)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND CLEANING
(continued)
Oven Light Replacement (on some models)
CAUTION: Before replacing your oven light bulb,
disconnect the electrical power to the range at the
main fuse or circuit breaker panel. Be sure to let
the light cover and bulb cool completely.
DO NOT REMOVE ANY SCREWS TO
REMOVE COVER.
2. Do not touch hot bulb with a wet cloth. Replace
bulb with a 40-watt household appliance bulb.
The oven light bulb is covered with a removable
glass cover that is held in place with a bail-shaped
wire. Remove the oven door, if desired, to reach
cover easily.
To replace cover:
1. Place it into the groove of the light receptacle. Pull
the wire forward to the center of the cover until it
snaps into place. When in place, the wire holds the
cover firmly. Be certain the wire is in the
To remove:
1. Hold a hand under the
cover so it doesn’t fall
when released. With
fingers of the same
depression in the center of the cover.
2. Connect electrical power to the range.
hand, firmly push back
the wire cover holder.
Lift off the cover.
Wire cover holder
Control Panel and Knobs
It’s a good idea to wipe the control panel after each
use of the oven. Clean with mild soap and water or
vinegar and water, rinse with clean water and polish
dry with a soft cloth.
The control knobs may be
removed for easier cleaning.
To remove a knob, pull it
straight off the stem. If knob
is difficult to remove, place
Do not use abrasive cleansers, strong liquid cleaners,
plastic scouring pads or oven cleaners on the control
panel—they will damage the finish. A 50/50 solution
of vinegar and hot water works well.
a towel or dishcloth between
the knob and control panel and pull gently. Wash the
knobs in soap and water or a vinegar and hot water
solution but do not soak.
Metal parts can be cleaned with soap and water.
Do not use steel wool, abrasives, ammonia, acids or
commercial oven cleaners. Dry with a soft cloth.
Removable Storage Drawer (on some models)
The storage drawer is a good place to store cookware
and bakeware. Do not store plastics and flammable
material in the drawer.
To remove the storage drawer:
1. Pull the drawer straight
out until it stops.
Do not overload the storage drawer. If the drawer is
too heavy, it may slip off the track when opened.
2. Tilt the front of the
drawer up and free of
the range.
The storage drawer may be removed for cleaning
under the range. Clean the storage drawer with a
damp cloth or sponge. Never use harsh abrasives or
scouring pads.
To replace the storage drawer:
1. Set the stops on the back of the drawer over the
stops in the range.
2. Slide the drawer evenly and straight back, so that
the rails in the range are engaged.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Oven Air Vents
Never block the vents (air openings) of the range.
They provide the air inlet and outlet that are necessary
for the range to operate properly with correct
combustion. Air openings are located at the rear of the
cooktop, at the top and bottom of the oven door, and at
the bottom of the range, under the kick panel, storage
drawer or broiler drawer (depending on the model).
Vent appearance and location vary
Lift-up Cooktop (on models with standard twin burners)
Clean the area under the cooktop often. Built-up soil,
especially grease, may catch on fire.
Some models have dual
support rods that will hold
the cooktop up while you
clean underneath it.
To make cleaning easier, the cooktop may be lifted up.
To raise the cooktop:
After cleaning under the
cooktop with hot, soapy
water and a clean cloth,
lower the cooktop. Be
1. Be sure the burners are turned off.
2. Remove the grates.
3. Grasp the two front burner wells and lift up.
careful not to pinch your fingers.
Removable Kick Panel (on some models)
The kick panel may be removed for cleaning under
the range.
To replace, insert the two
slots at the bottom of the panel
onto the two tabs at the base
of the range and push the top
of the panel forward to engage
the spring clips.
To remove, lift up the
bottom of the panel slightly
to disengage the panel from
the tabs at the base of the
range. Pull the bottom of the
panel forward until the spring
clips are released at the top of
the panel.
Removable Broiler Drawer (on some models)
To remove:
1. When the broiler is cool, remove the grid and pan.
2. Pull the broiler drawer out until it stops, then push
it back in about one inch.
3. Grasp the handle, lift and pull the broiler drawer
out. Clean the broiler drawer with hot soapy water.
To replace:
Hold the broiler drawer in the raised position as you
slide it partway into the range. Then lower the drawer
and push it completely closed.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
FOR YOUR SAFETY
CAUTION
If you smell gas:
Do not attempt to operate the oven of
this range during a power failure (Electric
Ignition models only).
1. Open windows.
2. Don’t touch electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier.
IMPORTANT
Remove all packing material and
literature from oven before connecting
gas and electrical supply to range.
FOR YOUR SAFETY
Do not store or use combustible
materials, gasoline or other flammable
vapors and liquids in the vicinity of this
or any other appliance.
DIMENSIONS AND CLEARANCES
Provide adequate clearances between the range
and adjacent combustible surfaces.
BEFORE YOU BEGIN
Depth with Door Closed
(Includes Door Handle):
30″
Read these instructions completely and
1
4
28 ⁄ ″
carefully.
SET
TIME
IMPORTANT: Save these instructions
for the local electrical inspector’s use.
electric ignition
INSTALLER: Leave these instructions
with the appliance after installation is
completed.
CONSUMER: Keep this Use and Care
Guide and the Installation Instructions
for future use.
F
L
I
TE
F
L
W
O
I
TE
I
W
O
I
F
L
I
TE
F
L
W
O
I
TE
I
W
O
I
1
1
Height
4″±
″
4
⁄
36 ⁄
1
2
46 ⁄ ″
SHELVES
This appliance must be properly grounded.
Depth with
Door Open:
WARNING
• Improper installation, adjustment,
alteration, service or maintenance can
cause injury or property damage. Refer to
this guide. For assistance or additional
information, consult a qualified installer,
service agency, manufacturer (dealer) or
the gas supplier.
3
8
46 ⁄ ″
• Never reuse old flexible connectors.
The use of old flexible connectors can
cause gas leaks and personal injury.
Always use NEW flexible connectors
when installing a gas appliance.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
• If cabinets are placed above the range, allow a
minimum clearance of 30″ between the cooking
surface and the bottom of unprotected cabinets.
• If a 30″ clearance between cooking surface
and overhead combustible material or metal
cabinets cannot be maintained, protect the
underside of the cabinets above the cooktop with
not less than 1/4″ insulating millboard covered
with sheet metal not less than 0.0122″ thick.
Installation of this range must conform with
local codes, or in the absence of local codes,
with the National Fuel Gas Code, ANSI
Z223.1, latest edition. In Canada, installation
must conform with the current Natural Gas
Installation Code, CAN/CGA-B149.1 or the
current Propane Installation Code, CAN/CGA-
B149.2, and with local codes where applicable.
This range has been design-certified by the
American Gas Association according to ANSI
Z21.1, latest edition and Canadian Gas Association
according to CAN/CGA-1.1 latest edition. As with
any appliance using gas and generating heat,
there are certain safety precautions you should
follow. You will find these precautions in the
Important Safety Instructions in the front of this
guide. Read them carefully.
• Clearance between the cooking surface and
protected cabinets MUST NEVER BE LESS
THAN 24 INCHES. The vertical distance from
the plane of the cooking surface to the bottom of
adjacent overhead cabinets extending closer than
1″ to the plane of the range sides must not be
less than 18″. (See Dimensions and Clearances
illustration in this section.)
• CAUTION: Items of interest to children should
not be stored in cabinets above a range or on the
backsplash of a range—children climbing on the
range to reach items could be seriously injured.
• Have your range installed by a qualified
installer or service technician.
• Your range must be electrically grounded in
accordance with local codes or, in the absence
of local codes, in accordance with the National
Electrical Code (ANSI/NFPA 70, latest edition).
In Canada, electrical grounding must be in
accordance with the current CSA C22.1 Canadian
Electrical Code Part 1 and/or local codes. See
Electrical Connections in this section.
• Before installing your range on linoleum or
any other synthetic floor covering, make sure
the floor covering can withstand 180°F. without
shrinking, warping or discoloring. Do not install
the range over carpeting unless a sheet of 1/4″
thick plywood or similar insulator is placed
between the range and carpeting.
WARNING
All ranges can tip and injury could
result. To prevent accidental tipping
of the range, attach an approved
Anti-Tip device to the wall. (See
Installing the Anti-Tip Device in this
section.) To check if the device is
installed and engaged properly,
carefully tip the range forward. The
Anti-Tip device should engage and prevent the
range from tipping over.
If you pull the range out from the wall for any
reason, make sure the Anti-Tip device is engaged
when you push the range back against the wall.
• Make sure the wall coverings around the
range can withstand heat generated by the
range up to 200°F.
• For your safety, never use your range for
warming or heating the room. Your oven and
cooktop are not designed to heat your kitchen.
Top burners should not be operated without
cookware on the grate. Such abuse could result
in fire and damage to your range and will void
your warranty.
• Do not store or use combustible materials,
gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.
Explosions or fires could result.
• Avoid placing cabinets above the range. To
reduce the hazard caused by reaching over the
open flames of operating burners, install a
ventilation hood over the range that projects
forward at least 5″ beyond the front of the cabinets.
• The ventilating hood must be constructed of
sheet metal not less than 0.0122″ thick. Install
above the cooktop with a clearance of not less
than 1/4″ between the hood and the underside
of the combustible material or metal cabinet.
The hood must be at least as wide as the
appliance and centered over the appliance.
Clearance between the cooking surface and the
ventilation hood surface MUST NEVER BE
LESS THAN 24 INCHES.
• Do not use oven for a storage area. Items
stored in the oven can ignite.
• Do not let cooking grease or other flammable
materials accumulate in or near the range.
EXCEPTION: Installation of a listed microwave
oven or cooking appliance over the cooktop shall
conform to the installation instructions packed
with that appliance.
(continued next page)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
(continued)
GENERAL
TOOLS YOU WILL NEED
• See Dimensions and Clearances in this section
for all rough-in and spacing dimensions. These
dimensions must be met for safe use of your range.
The location of the electrical outlet and pipe opening
(see Gas Pipe and Electric Outlet Locations) may
be adjusted to meet specific requirements.
• Phillips and flat-blade screwdrivers
• Pencil and ruler
• Two pipe wrenches (one for backup)
3
8
• 1 ⁄ ″ open-end or adjustable wrench
• Nut drivers or wrenches: 3/16″ and 1/4″
• The range may be placed with 0″ clearance
(flush) at the back wall and side walls of the range.
ADDITIONAL MATERIALS YOU MAY NEED
• Gas line shut-off valve
LOCATION
• Pipe joint sealant or UL-approved pipe thread
tape with Teflon* that resists action of natural
and LP gases
• Flexible metal appliance connector (1/2″ I.D.)
A 5-foot length is recommended for ease of
installation but other lengths are acceptable.
Never use an old connector when installing a
new range.
Do not locate the range where it may be subject
to strong drafts. Any openings in the floor or wall
behind the range should be sealed. Make sure
the openings around the base of the range that
supply fresh air for combustion and ventilation
are not obstructed by carpeting or woodwork.
• Flare union adapter for connection to gas
supply line (3/4″ or 1/2″ NPT x 1/2″ I.D.)
PROTECT YOUR FLOOR
• Flare union adapter for connection to pressure
regulator on range (1/2″ NPT x 1/2″ I.D.)
*Teflon: Registered trademark of DuPont
Your range, like many other household items, is
heavy and can settle into soft floor coverings
such as cushioned vinyl or carpeting. Use care
when moving the range on this type of flooring.
It is recommended that the following simple and
inexpensive instructions be followed to protect
your floor.
PREPARATION
• Remove all tape and packaging. Lift up the
cooktop (on models with standard twin burners)
and remove any packing material under it. Make
sure the standard twin burners are properly
seated and level.
The range should be installed on a sheet of plywood
(or similar material). When the floor covering ends
at the front of the range, the area that the range
will rest on should be built up with plywood to
the same level or higher than the floor covering.
This will allow the range to be moved for cleaning
or servicing.
• Remove plastic film that covers some chrome
parts (around oven door, side trim).
• Take the accessory pack out of the oven.
• Check to be sure that no range parts have
come loose during shipping.
MODEL AND SERIAL NUMBER LOCATION
Depending on your range, you’ll find the model
and serial numbers on a label on the front frame
of the range, behind the storage drawer, kick
panel or broiler drawer.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
1
PROVIDE ADEQUATE GAS SUPPLY
Gas Pipe and Electric Outlet Locations
for Models Equipped with Sealed Burners
Your range is designed to operate at a pressure
of 4″ of water column on natural gas or, if designed
for LP gas (propane or butane), 10″ of water
column. Make sure you are supplying your range
with the type of gas for which it is designed. This
range is convertible for use on natural or propane
gas, if you decide to use this range on a different
type of gas, conversion adjustments must be
made by a service technician or other qualified
person before attempting to operate the range on
that gas.
This area allows
for flush range
installation with
30
"
through-the-wall
21⁄2
connection of pipe
stub/shut-off valve
and rear wall
"
4
"
8
120V outlet.
"
Shortest
connection
from hard pipe
stub location to
range hookup.
For proper operation, the pressure of natural gas
supplied to the regulator must be between 4″ and
13″ of water column. For LP gas, the pressure
supplied must be between 10″ and 13″ of water
column. When checking for proper operation of
the regulator, the inlet pressure must be at least
1″ greater than the operating (manifold) pressure
as given above. The pressure regulator located
at the inlet of the range manifold must remain in
the supply line regardless of whether natural or
LP gas is being used. A flexible metal appliance
connector used to connect the range to the gas
supply line should have an I.D. of 1/2″ and be
5 feet in length for ease of installation. In Canada,
flexible connectors must be single wall metal
connectors no longer than 6 feet in length.
24
"
2
"
4
"
61⁄4
9
"
C
"
L
This area allows for
flush range installation
with through-the-floor
connection of pipe
stub/shut-off valve.
Gas Pipe and Electric Outlet Locations for
Models Equipped with Standard Twin Burners
Shortest
connection
from hard pipe
stub location to
range hookup.
This area allows
for flush range
installation with
through-the-wall
connection of pipe
stub/shut-off valve
and rear wall
2
CONNECT THE RANGE TO GAS
Shut off the main gas supply valve before
disconnecting the old range and leave it off until
new hook-up has been completed. Don’t forget
to relight the pilot on other gas appliances when
you turn the gas back on.
Because hard piping restricts movement of the
range, the use of an A.G.A.-certified flexible
metal appliance connector is recommended
unless local codes require a hard-piped connection.
Never use an old connector when installing a
new range. If the hard piping method is used,
you must carefully align the pipe; the range
cannot be moved after the connection is made.
30
"
120V outlet.
4
"
7
"
8
"
29
"
24
"
2
"
21⁄2
To prevent gas leaks, put pipe joint compound
on, or wrap pipe thread tape with Teflon*
around, all male (external) pipe threads.
"
9
"
C
L
*Teflon: Registered trademark of DuPont
This area allows
for flush range
installation with
through-the-floor
connection of pipe
stub/shut-off valve.
(continued next page)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
(continued)
CONNECT THE RANGE TO GAS (continued)
Flexible Connector and Rigid Pipe Hookups for
Models Equipped with Standard Twin Burners
Flexible Connector Hookup for Models
Equipped with Sealed Burners
Flexible
Connector
Hookup
Rigid Pipe
Hookup
Pressure
Regulator
Pressure
90°
Elbow
Union
Regulator
Nipple
Adapter
Gas Flow into Range
90° Elbow
(provided)
Flex
Gas Flow into Range
Connector
(6 ft. max.)
Black Iron Pipe
Adapter
Flex Connector
(6 ft. max.)
Union
Nipple
Manifold Pipe
Adapter
Adapter
Gas
Shut-off
Valve
Gas
Shut-off
Valve
Installer: Inform the
consumer of the
location of the gas
shut-off valve.
Installer: Inform the
consumer of the location
of the gas shut-off valve.
1/2" or 3/4"
Gas Pipe
1/2" or 3/4"
Gas Pipe
Rigid Pipe Hookup for Models Equipped
with Sealed Burners
Pressure
Regulator
90° Elbow
(provided)
90° Elbow
Black
Iron Pipe
Nipple Union
Union
Nipple
Gas Flow into Range
Installer: Inform the
consumer of the
location of the gas
shut-off valve.
Gas
Shut-off
Valve
1/2" or 3/4"
Gas Pipe
38
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
CONNECT THE RANGE TO GAS (continued)
ELECTRICAL CONNECTIONS (on some models)
1. Install a manual gas line shut-off valve in the
gas line in an easily accessed location outside of
the range. Make sure everyone operating the
range knows where and how to shut off the gas
supply to the range.
2. Install male 1/2″ flare union adapter to the
1/2″ NPT internal thread elbow at inlet of
regulator. On models equipped with dual
burners, install the male pipe thread end of
the 1/2″ flare union adapter to the 1/2″ NPT
internal thread at inlet of pressure regulator.
Use a backup wrench on the regulator fitting
to avoid damage.
Electrical Requirements
120-volt, 60 Hertz, properly grounded branch
circuit protected by a 15-amp or 20-amp circuit
breaker or time delay fuse.
Extension Cord Cautions
Because of potential safety hazards associated
with certain conditions, we strongly recommend
against the use of an extension cord. However,
if you still elect to use an extension cord, it is
absolutely necessary that it be a UL-listed,
3-wire grounding-type appliance extension cord
and that the current carrying rating of the cord
in amperes be equivalent to, or greater than,
the branch circuit rating.
When installing the range from the front,
remove the 90° elbow for easier installation.
Grounding
IMPORTANT—(Please read carefully)
3. Install male 1/2″ or 3/4″ flare union adapter
to the NPT internal thread of the manual shut-
off valve, taking care to back-up the shut-off
valve to keep it from turning.
4. Connect flexible metal appliance connector
to the adapter on the range. Position range
to permit connection at the shut-off valve.
5. When all connections have been made, make
sure all range controls are in the off position and
turn on the main gas supply valve. Use a liquid
leak detector at all joints and connections to
check for leaks in the system.
FOR PERSONAL SAFETY, THIS APPLIANCE
MUST BE PROPERLY GROUNDED.
The power cord of this appliance is equipped
with a three-prong (grounding) plug which
mates with a standard three-prong grounding
wall receptacle
PREFERRED
METHOD
to minimize the
possibility of
electric shock
hazard from
this appliance.
CAUTION: DO NOT USE A FLAME TO
CHECK FOR GAS LEAKS.
The customer
should have the
Ensure proper
wall receptacle
ground exists
before use
and circuit
When using test pressures greater than 1/2 psig
to pressure test the gas supply system of the
residence, disconnect the range and individual
shut-off valve from the gas supply piping. When
using test pressures of 1/2 psig or less to test the
gas supply system, simply isolate the range from
the gas supply system by closing the individual
shut-off valve.
checked by a
qualified electrician to make sure the receptacle
is properly grounded.
Where a standard two-prong wall receptacle is
encountered, it is the personal responsibility and
obligation of the customer to have it replaced with
a properly grounded three-prong wall receptacle.
DO NOT, UNDER ANY CIRCUMSTANCES,
CUT OR REMOVE THE THIRD (GROUND)
PRONG FROM THE POWER CORD.
(continued next page)
39
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
(continued)
ELECTRICAL CONNECTIONS (continued)
B
Usage Situations where Appliance Power
Cord will be Disconnected Frequently.
A
Usage Situations where Appliance
Do not use an adapter plug in these situations
because disconnecting of the power cord
places undue strain on the adapter and leads to
eventual failure of the adapter ground terminal.
The customer should have the two-prong
wall receptacle replaced with a three-prong
(grounding) receptacle by a qualified electrician
before using the appliance.
The installation of appliances designed for
mobile home installation must conform with
the Manufactured Home Construction and
Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile
Home Construction and Safety, Title 24, HUD,
Part 280) or, when such standard is not
applicable, the Standard for Manufactured
Home Installations, latest edition (Manufactured
Home Sites, Communities and Set-Ups), ANSI
A225.1, latest edition, or with local codes. In
Canada, mobile home installation must be in
accordance with the current CAN/CSA
Z240/MH Mobile Home Installation Code.
Power Cord will be Disconnected Infrequently.
An adapter may be used only on a 15-amp
circuit. Do not use an adapter on a 20-amp
circuit. Where local codes permit, a
TEMPORARY CONNECTION may be
made to a properly grounded two-prong wall
receptacle by the use of a UL-listed adapter,
available at most hardware stores. The larger
slot in the adapter must be aligned with the
larger slot in the wall receptacle to provide
proper polarity in the connection of the
power cord.
TEMPORARY
METHOD
(Adapter plugs not
permitted in Canada)
Align large
Ensure proper
prongs/slots
ground and
firm connection
before use
Electric Disconnect
CAUTION: Attaching the adapter ground
terminal to the wall receptacle cover screw
does not ground the appliance unless the cover
screw is metal, and not insulated, and the wall
receptacle is grounded through the house
wiring. The customer should have the circuit
checked by a qualified electrician to make sure
the receptacle is properly grounded.
1. Locate disconnect plug on the range back.
2. Pinch sides of connector and pull out of
range back.
You will have this disconnect plug.
When disconnecting the power cord from the
adapter, always hold the adapter with one hand.
If this is not done, the adapter ground terminal
is very likely to break with repeated use. Should
this happen, DO NOT USE the appliance until a
proper ground has again been established.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
4
SEAL THE OPENINGS
Quality of Flames
Seal any openings in the wall behind the range
and in the floor under the range when hookups
are completed.
The combustion quality of burner flames needs
to be determined visually.
(A) Yellow flames—
Call for service
5
CHECK IGNITION OF SURFACE BURNERS
Surface Burner Ignition
(B) Yellow tips on
outer cones—
Operation of all cooktop and oven burners
should be checked after the range and gas
supply lines have been carefully checked
for leaks.
Normal for LP gas
(C) Soft blue flames—
Normal for natural gas
Electric Ignition Models
Select a top burner knob and simultaneously
push in and turn to LITE position. You will hear
a snapping sound indicating proper operation
of the spark module. Once the air has been
purged from the supply lines, burners should
light within 4 seconds. After burner lights,
rotate knob out of the LITE position. Try each
burner in succession until all burners have
been checked.
If burner flames look like (A), call for service.
Normal burner flames should look like (B) or
(C), depending on the type of gas you use.
With LP gas, some yellow tipping on outer
cones is normal.
6
CHECK IGNITION OF OVEN BURNER
Your oven is designed to operate quietly and
automatically. To operate the oven, turn the OVEN
SET knob to BAKE and the OVEN TEMP knob
to a setting above 300°F. After 30-90 seconds, the
oven burner will ignite and burn until the set
temperature is reached. The oven burner will
continue to cycle on and off as necessary to
maintain the oven at the temperature indicated by
the OVEN TEMP knob.
To check ignition of the broil burner, turn the
OVEN SET knob to BROIL and the OVEN
TEMP knob to BROIL. After 30-90 seconds, the
broil burner will ignite.
Electric ignition models require electrical
power to operate. In case of a power outage, the
oven burners on these models cannot be lit
manually with a match. Gas will not flow unless
the glow bar is hot.
If the oven is in use when a power outage occurs,
the burner will shut off and cannot be re-lit until
power is restored.
(continued next page)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
(continued)
7
ADJUST BROIL AND OVEN BURNER AIR
ADJUSTMENT SHUTTERS IF NECESSARY
Air adjustment shutters for the top and bottom
burners regulate the flow of air to the flames.
Air Adjustment
Shutter
To determine if the bottom burner flames are
burning properly, remove the oven bottom.
Flames should have approximately 1″ blue cones
and, if range is supplied with natural gas, should
burn with no yellow tipping. (With most LP gas,
small yellow tips at the end of outer cones are
normal.) Flames should not lift off burner ports.
If lifting is observed, gradually reduce air shutter
opening until flames are stabilized.
Loosen
The air adjustment shutter for the top
(broil) burner is in the center of the rear
wall of the oven.
Oven Bottom
Loosen
To remove the oven bottom:
1. Remove the knurled screws holding down rear
of the oven bottom.
Air Adjustment
Shutter
2. Grasp the oven bottom at finger slots on
each side.
3. Lift the rear of the oven bottom enough to
clear the lip of the range frame, then pull out.
The shutter for the bottom (oven) burner is near
the back wall behind the storage drawer or the
kick panel (depending on the model). Remove
the drawer or panel. See the Care and Cleaning
section in this guide.
To adjust the flow of air to either burner, loosen
the Phillips head screw and rotate the shutter
toward open or closed position as needed.
The flames for the top (broil) burner should be
steady with approximately 1″ blue cones and should
not extend out over the edges of the burner baffle.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Anti-Tip
Device
8
LEVELING THE RANGE
1. Remove the storage
drawer, broiler drawer or
kick panel.
Slotted
Head
Screw
Wallplate
Approx.
20°
2. Use a 3/16″ open-end
or socket wrench to back
out both rear leveling legs
approximately two turns.
3
Marked Edge
of Range
1
8
2 ⁄ ″
8
3. Use a 1 ⁄ ″ open-end or
adjustable wrench to back
out the front leveling legs
two turns.
1
8
2. Locate the outside edge of the device 2 ⁄ ″
toward the center of the range from the marked
edge of the range.
4. Install the oven shelves
in the oven and position
3. Using the device as a template, mark the
the range where it will be installed.
position of the hole for the screw.
5. Check for levelness by placing a spirit level or
a cup, partially filled with water, on one of the
oven racks. If using a spirit level, take two
readings—with the level placed diagonally first
in one direction and then the other.
4. For wood construction, drill a pilot hole at an
angle of 20 degrees from the horizontal. A nail
or awl may be used if a drill is not available.
Mount the Anti-Tip device with the screw
provided.
6. Adjust the leveling legs until the range is level.
For cement or concrete construction, you
1
7. After the range is level, slide the range away
from the wall so that the Anti-Tip device can be
installed.
2
will need a 1/4″ x 1 ⁄ ″ lag bolt and a 1/2″ O.D.
sleeve anchor, which are not provided. Drill
the recommended size hole for the hardware.
Install the sleeve anchor into the drilled hole
and then install the lag bolt through the device.
The bolts must be properly tightened as
recommended for the hardware.
9
INSTALLING THE ANTI-TIP DEVICE
Back of
Wallboard
WARNING:
Range
• Range must be secured with an approved
Anti-Tip
Device
Anti-Tip device.
• Unless properly installed, the range could
be tipped by you or a child standing, sitting
or leaning on an open door.
Wood Screw
• After installing the Anti-Tip device, verify
that it is in place by carefully attempting to
tilt the range forward.
Wallplate
• This range has been designed to meet all
recognized industry tip standards for all
normal conditions.
• The use of this device does not preclude
tipping of the range when not properly
installed.
5. Slide the range against the wall, and check
for proper installation by grasping the front
edges of the rear surface unit openings and
carefully attempting to tilt the range forward.
• If the Anti-Tip device supplied with the
range does not fit this application, use the
universal Anti-Tip device WB02X7909.
WHEN ALL HOOKUPS ARE COMPLETED:
MAKE SURE ALL CONTROLS ARE LEFT IN THE
OFF POSITION.
MAKE SURE THE FLOW OF COMBUSTION AND
VENTILATION AIR TO THE RANGE IS UNOBSTRUCTED.
1. Mark the wall where the RIGHT EDGE of the
range is to be located. Be sure to allow for the
countertop overhang if you intend to install the
range next to cabinets.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
CONVERTING TO LP GAS (Sealed Burner models only)
or Converting Back to Natural Gas from LP
HOW TO CONVERT A SEALED BURNER RANGE
A
If It Is This Regulator:
FOR USE WITH LP GAS OR NATURAL GAS
1. Use an adjustable wrench to remove the
nut from the pressure regulator.
Lever shown
closed. PULL
TO OPEN.
This range leaves the factory set for use with natural
gas. If you convert to LP gas, keep these instructions
and orifices in case you want to convert back to
natural gas.
Gas Flow
into Range
The conversion should be done by a qualified
technician or installer.
LP
Converter
nut and pin
TOOLS REQUIRED:
Adjustable wrench
1/2″ open-end wrench
Flat blade screwdriver (small)
NAT
2. Apply sideward finger pressure to remove
the plastic pin from the nut.
Nut drivers or wrenches: 9/32″ or 7mm
HINT: To remove the pin, place the nut on
a flat surface and press the pin sideways with
your fingers.
3. Push down on the disc edges to replace the
1
PREPARE RANGE FOR CONVERSION
pin in the nut.
(1) Turn off gas supply at the wall.
(2) Turn off the electrical power to the range.
LP
NAT
If range has not yet been connected to gas supply,
or if flexible connection was made, range may be
pulled out from the wall to make conversion easier.
4. Reinsert the assembly into the regulator.
2
CONVERT THE PRESSURE REGULATOR
WARNING: Do not remove the pressure
regulator from the range.
B
If It Is This Regulator:
Gas Flow
into Range
Lever shown closed.
PULL TO OPEN.
1. Remove the broiler drawer and locate the
pressure regulator at the rear of the range.
N
NAT
Do not
remove this
protective
cap except
for conversion
LP
Cap
Assembly
On some models, you may have to remove an
access cover also.
1. Unscrew the plastic-protected hex-nut
cap from the regulator.
2. Follow the directions in box A or B that
match your regulator type.
2. Carefully pry the protective plastic cap off
the threaded metal cap. Gently pull the plastic
washer off the threads on the other side of the
metal cap.
3. Push the plastic cap onto the end of the metal
cap displaying the type of gas you are converting
to. Press the attached plastic washer onto the
threads on the other side of the metal cap.
4. Screw the hex-nut cap back into the regulator.
Do not overtighten.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
CONVERTING TO LP GAS (Sealed Burner models only)
or Converting Back to Natural Gas from LP
A
3
CONVERTING SURFACE BURNERS
Orifice Spuds for Converting to LP Gas:
LP orifice spuds are in a small plastic bag packed
with this Use and Care Guide or on a bracket
next to the pressure regulator. LP orifice spuds
have a 2-digit number and the letter “L” on top.
Each orifice spud will also have 1, 2 or 3 grooves
on the top, and some will have a painted side,
denoting the location on the range where it is to
be installed as shown below.
Grate
Burner Cap
Drip Pan
(on some models)
Burner Head
Electrode
I
II
Brass
Brass
White
1. Remove grates, burner caps and burner heads.
2. Remove the brass orifice
spud inside the chimney of
each burner using a 9/32″
or 7 mm nut driver.
III
II
Front of Range
Brown
Chimney
3. Install the orifice spuds
according to one of the
following diagrams (see
A
B
or ), for LP gas or
Orifice Spuds for Converting to Natural Gas:
B
natural gas, depending on
Natural gas orifice spuds have a 3-digit number
and the letter “N” on the top. Each orifice spud
will also have 1, 2 or 3 grooves on top denoting
the location on the range where it is to be
installed as shown below.
which you are converting to.
Orifice spud
Front of Range
(continued next page)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
CONVERTING TO LP GAS (Sealed Burner models only)
or Converting Back to Natural Gas from LP
4. To prevent leakage, make sure the orifice
4
CONVERT THE OVEN BURNER ORIFICES
spuds are securely screwed into the gas
inlet tubes.
Oven Burner
1. Remove oven door, storage drawer or broiler
drawer and oven bottom. The lower burner
orifice spud is located behind the storage
drawer, broiler drawer or kick panel. (On some
models, a metal shield must be removed to
access the orifice.)
5. Put old orifice spuds back in the bag or on the
bracket next to the pressure regulator to save for
possible future conversion.
NOTE: If an orifice spud
is accidentally dropped,
the cooktop can be
2. To convert to LP gas,
use a 1/2″ wrench to
turn the lower burner
orifice spud clockwise.
Tighten the spud only
until it is snug. To
raised. Release the 2
front clips with a large
flat blade screwdriver
and remove the 4 screws
under the burner heads.
Remove screw
under each
burner head
When lowering it,
prevent damage, do not
make sure it snaps
overtighten the spud.
over the clips.
To convert to natural gas,
loosen the spud about 2 turns.
Broil Burner (on some models)
To convert to LP gas, use a 1/2″ wrench to
turn the upper burner orifice spud clockwise.
Tighten spud only until it is snug with the base.
To prevent damage, do not overtighten spud.
To convert to natural gas, loosen the spud
about 2 turns.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
CONVERTING TO LP GAS (Sealed Burner models only)
or Converting Back to Natural Gas from LP
5
7
CONVERT AIR ADJUSTMENT SHUTTER
ADJUST LOW FLAME SETTINGS
For LP gas, loosen the
Phillips head screw and
rotate the shutter to the
NOTE: Only valves with
these types of knobs are
adjustable.
Screw
full open position. With
baffle in place, flames
Air Shutter
should have approximately
1-inch blue cones and
should not extend beyond
the edges of the burner baffle. After 30 seconds
of burner operation, check for flames lifting off
burner ports. If lifting is observed, gradually
reduce air shutter opening until flames are
stabilized.
1. Turn all of the top burners to LOW.
2. Remove all four knobs.
3. With a small flat blade
For natural gas, the shutter should be open
screwdriver, turn the
1/2″ or about 3/4 of the way open.
valve set screws
clockwise to decrease
the flame size,
counterclockwise to
6
CHECK FOR LEAKS
increase the flame size. Adjust until the flame is
When all connections have been made, make sure
all range controls are in the off position and turn
on the main gas supply valve. Use a liquid leak
detector at all joints and connections to check for
leaks in the system.
about the same height as the top of the burner.
4. Replace the knobs.
5. Check for flame outage by opening and
closing the oven door several times. If the flame
goes out, increase the flame size.
CAUTION: DO NOT USE A FLAME TO
CHECK FOR GAS LEAKS.
8
CHECK QUALITY OF FLAMES
When using test pressures greater than 1/2 psig
to pressure test the gas supply system of the
residence, disconnect the range and individual
shut-off valve from the gas supply piping. When
using test pressures of 1/2 psig or less to test the
gas supply system, simply isolate the range from
the gas supply system by closing the individual
shut-off valve.
The combustion quality of burner flames needs
to be determined visually.
(A) Yellow flames—
Call for service
(B) Yellow tips on outer
cones—Normal for LP gas
(C) Soft blue flames—
Normal for natural gas
If burner flames look like (A), call for service.
Normal burner flames should look like(B) or
(C), depending on the type of gas you use.
With LP gas, some yellow tipping on outer cones
is normal.
The conversion for sealed burner models is
now complete.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
CONVERTING TO LP GAS (Standard Twin Burner models only)
or Converting Back to Natural Gas from LP
HOW TO CONVERT A STANDARD TWIN
B
If It Is This Regulator:
Gas Flow into
Range
BURNER RANGE FOR USE WITH LP GAS OR
NATURAL GAS
This range leaves the factory set for use with natural
gas. If you convert to LP gas, keep these instructions
and orifices in case you want to convert back to
natural gas. The conversion should be done by a
qualified technician or installer.
Do not remove
this protective
cap except for
conversion.
N
NAT
LP
TOOLS REQUIRED:
Adjustable wrench
1/2″ open-end wrench
Flat blade screwdriver (small)
Lever shown
closed. PULL
TO OPEN.
Cap Assembly
1. Unscrew the plastic-protected hex-nut cap
from the regulator.
Nut drivers: 7mm, 5/16″ or a small adjustable
2. Carefully pry the protective plastic cap off
the threaded metal cap. Gently pull the plastic
washer off the threads on the other side of the
metal cap.
(depending on the size of the spuds)
3. Push the plastic cap onto the end of the metal
cap displaying the type of gas you are converting
to. Press the attached plastic washer onto the
threads on the other side of the metal cap.
1
PREPARE RANGE FOR CONVERSION
(1) Turn off gas supply at the wall.
(2) Turn off the electrical power to the range.
If range has not yet been connected to gas supply,
or if flexible connection was made, range may be
pulled out from the wall to make conversion easier.
4. Screw the hex-nut cap back into the regulator.
Do not overtighten.
C
If It Is This Regulator:
2
CONVERT THE PRESSURE REGULATOR
1. Use an adjustable
LP
Converter
wrench to remove the
nut from the pressure
regulator.
nut and pin
WARNING: Do not remove the pressure
regulator from the range.
2. Apply sideward
finger pressure to
remove the plastic pin
from the nut.
HINT: To remove the
pin, place the nut on
a flat surface and press
the pin sideways with
your fingers.
NAT
1. Remove the cooktop and locate the pressure
regulator at right rear of the range.
2. Follow the directions in box A B or C that
,
match your regulator type.
(Standing pilot models do
not have a gas shut-off
valve on the regulator.)
A
If It Is This Regulator:
NAT
Cap
LP
Cap
3. Push down on the disc edges to replace the
Gas Flow
into Range
pin in the nut.
4. Reinsert the
assembly into the
Lever shown
closed.
PULL TO OPEN.
NAT
LP
regulator.
1. Use a coin to remove the cap from the
pressure regulator.
2. Turn the cap over and hook it into the slots.
The type of gas to be used should now be visible
on the top of the cap.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
CONVERTING TO LP GAS (Standard Twin Burner models only)
or Converting Back to Natural Gas from LP
3
Broil Burner (on some models)
CONVERTING SURFACE BURNERS
To convert to LP gas,
use a 1/2″ wrench to
turn the upper
1. Lift cooktop.
2. Lift burner assemblies straight up and set
aside to gain access to surface burner spuds.
burner orifice spud
clockwise. Tighten
spud only until it is
snug with the base.
To prevent damage,
do not overtighten spud.
3. With a 7mm, 5/16″ or a small adjustable
wrench, remove each of the four spuds on the
surface burner
gas inlet tubes and
replace them with
Natural gas
= brass
LP gas =
red or silver
the correct gas
spuds mounted in
a holder at the
To convert to natural gas, loosen the spud
OR
about 2 turns.
right rear of the
range, above the
regulator. Natural
gas spuds are
5
CONVERT AIR ADJUSTMENT SHUTTER
For LP gas, loosen the
brass and LP gas
spuds are red or
silver. (Mount the
Phillips head screw and
Screw
rotate the shutter to the
Air Shutter
full open position. With
baffle in place, flames
spuds that you removed from the inlet tubes
back in the holder.) To prevent leakage, make
sure spuds are securely screwed into gas inlet
tubes.
should have approximately
1-inch blue cones and should not extend beyond
the edges of the burner baffle. After 30 seconds
of burner operation, check for flames lifting off
burner ports. If lifting is observed, gradually
reduce air shutter opening until flames are
stabilized.
4. Replace the burner assemblies.
5. Keep all spuds with your range so you have
them if you move or get a different gas hook-up.
For natural gas, the shutter should be open
Top Burner Orifice Drill Size
Natural Gas #54 (.0550 Dia.)
LP (Propane) #66 (.0330 Dia.)
Color
Brass
Red or Silver
1/2″ or about 3/4 of the way open.
6
CHECK FOR LEAKS
When all connections have been made, make sure
all range controls are in the off position and turn
on the main gas supply valve. Use a liquid leak
detector at all joints and connections to check for
leaks in the system.
4
CONVERT THE OVEN BURNER ORIFICES
Oven Burner
1. Remove oven door, storage drawer or broiler
drawer and oven bottom. The lower burner
orifice spud is located behind the storage drawer,
broiler drawer or kick panel. (On some models, a
metal shield must be removed to access the
orifice.)
CAUTION: DO NOT USE A FLAME TO
CHECK FOR GAS LEAKS.
When using test pressures greater than 1/2 psig
to pressure test the gas supply system of the
residence, disconnect the range and individual
shut-off valve from the gas supply piping. When
using test pressures of 1/2 psig or less to test the
gas supply system, simply isolate the range from
the gas supply system by closing the individual
shut-off valve.
2. To convert to LP gas,
use a 1/2″ wrench to
turn the lower burner
orifice spud clockwise.
Tighten the spud only
until it is snug. To
prevent damage, do not
overtighten the spud.
To convert to natural gas,
loosen the spud about 2 turns.
(continued next page)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
CONVERTING TO LP GAS (Standard Twin Burner models only)
or Converting Back to Natural Gas from LP
9
7
ADJUST LOW FLAME SETTING
CHECK QUALITY OF FLAMES
The combustion quality of burner flames needs
NOTE: Only valves with these
to be determined visually.
types of knobs are adjustable.
1. Turn all top burners to
LOW.
(A) Yellow flames—
Call for service
2. Remove all four knobs.
(B) Yellow tips on outer
3. With a small flat blade
screwdriver, turn the
cones—Normal for LP gas
valve set screws clockwise
to decrease flame size,
counterclockwise to
(C) Soft blue flames—
increase flame size. Adjust
until the flame is about the same
height as the top of the burner.
Normal for natural gas
If burner flames look like (A), call for service.
Normal burner flames should look like(B) or
(C), depending on the type of gas you use.
4. Replace the knobs.
5. Check for flame outage by opening and
closing the oven door several times. If the flame
goes out, increase the flame size.
With LP gas, some yellow tipping on outer cones
is normal.
The conversion for standard twin burner models
is now complete.
8
ADJUST THE SURFACE BURNER PILOTS
(for Models Equipped with Standing Pilots)
1. Raise the cooktop.
2. Locate the pilot adjustment screw. It can be
accessed through the small hole near the center
of the manifold panel.
3. To adjust, use a blade-type screwdriver with
a shaft diameter of less than 3/16″. Turn pilot
adjustment screw until pilot is 5/16″ high. Do
not reduce the flame to less than 5/16″ or pilot
outage may occur. A pilot flame burning higher
than recommended may generate soot (carbon
black) on the bottom of your cooktop.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
51
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
52
Download from Www.Somanuals.com. All Manuals Search And Download.
QUESTION?
BEFORE YOU CALL FOR SERVICE…
PROBLEM
POSSIBLE CAUSE
TOP BURNERS DO NOT
LIGHT OR DO NOT
BURN EVENLY
• Make sure electrical plug is plugged into a live power outlet.
• Burner holes on the side or around the top of burner may be clogged. Remove
burners (on models with standard twin burners) or burner heads (on models
with sealed burners) or burner caps on spill-proof models, and clean them
with a sewing needle or twist tie. Make sure you do not enlarge the holes. On
spill-proof models, check electrode area for burned-on food or grease.
• Make sure the drip pans are installed correctly.
BURNER FLAMES VERY
LARGE OR YELLOW
• If range is connected to LP gas, check all steps in the Installation Instructions.
SURFACE BURNERS
LIGHT BUT OVEN
DOES NOT
• The oven gas shut off valve may have accidentally been moved during
cleaning or moving.
To check the oven gas shut off valve on standard twin burner models, raise
the cooktop and look for the gas shut off lever at the extreme right rear corner.
(Standing pilot models do not have a gas shut off valve on the regulator.)
Follow the directions in box A or B that match your regulator type.
A
B
Lever shown closed.
PULL TO OPEN.
Lever shown closed.
PULL TO OPEN.
Standard Twin Burner Models
Standard Twin Burner Models
To check the oven gas shut off valve on sealed burner models, remove
the storage drawer, broiler drawer or kick panel and look for the gas shut
off lever at the back of the range.
Follow the directions in box A or B that match your regulator type.
A
B
Lever shown
closed. PULL
TO OPEN.
Lever shown
closed. PULL
TO OPEN.
Sealed Burner Models
Sealed Burner Models
CLOCK DOES NOT WORK
• Range electrical plug must be securely seated in a live power outlet. Check for
blown fuse or tripped circuit breaker.
OVEN LIGHT DOES NOT
COME ON
• Bulb may be loose or burned out.
• Electrical plug must be plugged into a live power outlet.
(continued next page)
53
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU CALL FOR SERVICE…
(continued)
PROBLEM
POSSIBLE CAUSE
OVEN WILL NOT WORK
• Plug on range is not completely inserted in the electrical outlet.
• The circuit breaker in your house has been tripped, or a fuse has been blown.
• Oven controls not properly set.
• Door left in locked position after cleaning.
OVEN TEMPERATURE
TOO HOT OR TOO COLD
• The OVEN TEMP knob needs adjustment. See the Adjust the Oven
Thermostat—Do It Yourself section.
FOOD DOES NOT ROAST
OR BAKE PROPERLY
• Oven controls not properly set. See the Baking or Roasting section.
• Shelf position is not correct.
• Incorrect cookware or cookware of improper size is being used.
• Oven thermostat needs adjustment. See the Adjust the Oven Thermostat—
Do It Yourself section.
• Clock not set correctly.
• Aluminum foil used improperly in the oven.
• Oven bottom not securely seated in position.
FOOD DOES NOT
BROIL PROPERLY
• Oven controls not properly set. See the Broiling section.
• Oven door and/or broiler drawer not closed.
• Improper shelf position being used. See the Broiling section.
• Food is being cooked on a hot pan.
• Cookware is not suited for broiling.
• Aluminum foil used on the broiler pan grid has not been fitted properly
and slit as recommended.
• Oven bottom not securely seated in position.
OVEN WILL NOT
SELF CLEAN
• Oven temperature is too high to set self-clean operation. Allow the range to cool
to room temperature and reset the controls.
• Door latch handle not moved all the way to the right.
OVEN NOT CLEAN AFTER
CLEAN CYCLE
• Oven controls not set properly. Review Operating the Self-Cleaning Oven section.
1
2
• Heavily soiled oven requires 3 ⁄ to 4 hours of cleaning time.
• Heavy spillovers should be cleaned up before starting clean cycle.
OVEN DOOR
ACCIDENTALLY LOCKED
WHILE BAKING
• Turn the OVEN SET knob to OFF. Allow the oven to cool and
then unlatch the door.
OVEN DOOR WILL
NOT UNLOCK
• Oven must cool below locking temperature. Do not lock the door with
door latch except when using self-clean feature or the oven may lock.
STRONG ODOR
• Improper air/gas ratio in oven. Adjust oven burner air shutter.
• An odor from the insulation around the oven liner is normal for the first few
times oven is used. This is temporary.
If you need more help…call, toll free:
GE Answer Center®
800.626.2000
consumer information service
54
Download from Www.Somanuals.com. All Manuals Search And Download.
We’ll Be There
With the purchase of your new Hotpoint appliance, receive the assurance that if you ever
need information or assistance, we’ll be there. All you have to do is call—toll-free!
GE Answer Center®
800.626.2000
Whatever your question about any Hotpoint major appliance, GE Answer
Center® information service is available to help. Your call—and your
question—will be answered promptly and courteously. And you can call any
time. GE Answer Center® service is open 24 hours a day, 7 days a week.
In-Home Repair Service
800-GE-CARES (800-432-2737)
Our consumer service professional will provide expert repair service on your
Hotpoint appliance, scheduled at a time that’s convenient for you. Many GE
Consumer Service company-operated locations offer you service today or
tomorrow, or at your convenience (7:00 a.m. to 7:00 p.m. weekdays, 9:00 a.m. to
2:00 p.m. Saturdays). Our factory-trained technicians know your appliance
inside and out—so most repairs can be handled in just one visit.
For Customers With Special Needs…
2’ 6"
TBXTOLITE
ON WALL
SINGLE CONTROL
FAUCET
800.626.2000
6’ 10"
8"
5"
6"
5"
7"
1’ 0"
Upon request, we will provide
Braille controls for a variety of
Hotpoint appliances, and a
brochure to assist in planning a
barrier-free kitchen for persons
with limited mobility. To obtain
these items, free of charge, call
800.626.2000.
Consumers with impaired hearing or speech who have
access to a TDD or a conventional teletypewriter may
call 800-TDD-GEAC (800-833-4322) to request
information or service.
1/8
3’ "
FLUORESCENT
FIXTURE
THIS LIGHT CAN
BE INSTALLED
IN BOTTOM OF
WALL CABINETS
2’ 10"
SECTION A-A
R SHALLOW DEPTH SINKS (6") WITH REAR DRAIN.
SINK SHOULD ALSO BE UNDERCOATED
SCALE 1’ 1"
=
Service Contracts
800-626-2224
You can have the secure feeling that GE Consumer Service will still be there
after your Hotpoint product warranty expires. Purchase a GE contract while
your warranty is still in effect and you’ll receive a substantial discount. With
a multiple-year contract, you’re assured of future service at today’s prices.
Parts and Accessories
800-626-2002
Individuals qualified to service their own appliances can
have parts or accessories sent directly to their home.
Our parts system provides access to over 47,000
Genuine Renewal Parts…and all are fully warranted.
VISA, MasterCard and Discover cards are accepted.
User maintenance instructions contained in this guide
cover procedures intended to be performed by any user.
Other servicing generally should be referred to qualified
service personnel. Caution must be exercised, since
improper servicing may cause unsafe operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
Staple sales slip or cancelled check
here. Proof of original purchase date
is needed to obtain service
under warranty.
YOUR HOTPOINT GAS RANGE
WARRANTY
FULL ONE-YEAR WARRANTY
For one year from date of original
purchase, we will provide, free of
charge, parts and service labor in
your home to repair or replace
any part of the range that fails
because of a manufacturing defect.
*******************************
WHAT IS COVERED
This warranty is extended to the
original purchaser and any succeeding
owner for products purchased for
ordinary home use in the 48 mainland
states, Hawaii, Washington, D.C. and
Canada. In Alaska the warranty is the
same except that it is LIMITED because
you must pay to ship the product to
the service shop or for the service
technician’s travel costs to your home.
All warranty service will be provided
by our Factory Service Centers or by
our authorized Customer Care®
servicers during normal working hours.
Should your appliance need service,
during the warranty period or beyond,
in the United States, call 800-GE-
CARES (800-432-2737). In Canada
consult your telephone directory for
the Camco Service Center.
• Service trips to your home to
• Improper installation.
WHAT IS NOT COVERED
teach you how to use the product.
If you have an installation problem,
contact your dealer or installer.
You are responsible for providing
adequate electrical, gas, exhausting
and other connecting facilities as
described in the Installation Instructions
provided with the product.
Read your Use and Care material.
If you then have any questions
about operating the product,
please contact your dealer or in
the United States, contact our
Consumer Affairs office at the
address below, or call, toll free:
GE Answer Center®
• Replacement of house fuses or
resetting of circuit breakers.
800.626.2000
consumer information service
• Failure of the product if it is used
for other than its intended purpose
or used commercially.
In Canada call:
800-361-3400
Customer Relations Manager
• Damage to product caused by
accident, fire, floods or acts of God.
WARRANTOR IS NOT RESPONSIBLE
FOR CONSEQUENTIAL DAMAGES.
Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state/province to province. To
know what your legal rights are in your state/province, consult your local or state/provincial consumer affairs office or your state’s Attorney General.
Warrantor—In the United States: General Electric Company
If further help is needed concerning this warranty, write:
Manager, Consumer Affairs, GE Appliances, Louisville, KY 40225
Warrantor—In Canada: Camco Inc.
If further help is needed concerning this warranty, write:
Manager, Customer Relations, Camco Inc., 1 Factory Lane, Suite 310, Moncton, N.B. E1C 9M3
This book is printed on recycled paper.
RGB744
RGB745
Part No. 183D5580P028
Pub No. 39-4760
Printed in Mexico
6-96 CG
Download from Www.Somanuals.com. All Manuals Search And Download.
|