Instruction booklet
DISHWASHER
Contents
EN
Installation, 2-5
Positioning and levelling
Technical data
English, 1
Electrical connection
Connecting the water supply
Ecodesign Regulation
Description of the appliance, 6
Overall view
Control panel
Loading the racks, 7
Lower rack
Cutlery basket
Upper rack
Start-up and use, 8-9
Starting the dishwasher
Loading the detergent
Washing options
LFT 2284
Wash cycles, 10
Wash cycle table
Rinse aid and refined salt, 11
Loading the rinse aid
Loading the refined salt
Care and maintenance, 12
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the water inlet filter
Cleaning the filters
Leaving the machine unused for extended periods
Precautions and advice, 13
General safety
Disposal
Saving energy and respecting the environment
Troubleshooting, 14
After Sales Service, 15
After Sales Service
Essential Contact Information
Parts and Accessories
Appliance Registration
Recycling and Disposal Information
Hotpoint Guarantee, 16
Download from Www.Somanuals.com. All Manuals Search And Download.
The dishwasher meets the requirements set out by the
regulations in force concerning safety and electrical
equipment.
Changing the Plug
EN
Cut off and dispose of the supplied plug if it does not fit
your socket.
Any technical checks should be conducted exclusively
by a trained and authorised technician: Repairs carried
out by unaithorised persons will invalidate the guarantee,
as well as posing a potential hazard to the user.
To avoid a shock hazard DO NOT insert the discarded
plug into a socket anywhere else.
Wires in the mains lead are coloured accordance with
the following code:
The manufacturer declines all responsibility for damage
to persons or property resulting from failure to observe the
above precautions, from tampering with even a single
component or from the use of non-original spare parts.
Green/Yellow -
Earth
Neutral
Live
Blue
Brown
-
-
Electrical Connection
Before inserting the plug into the electrical socket, make
sure that:
If you change the plug, the colour of the wires in the mains
lead may not correspond with the terminal markings in the
plug, which if not coloured, could be:
•
•
the socket is earthed and complies with current
regulations;
EARTH
NEUTRAL ‘N’
LIVE ‘L’
‘E’ or
the socket can withstand the maximum load of the
appliance, which is indicated on the data plate located
on the inside of the door (see Description of the
appliance);
Changing the Mains Lead
A lead can be ordered from Hotpoint Service
UK: 08709 066 066 or
•
•
the power supply voltage falls within the values indicated
on the data plate on the inside of the door;
Republic of Ireland: 1850 302 220
- If you have damaged the existing lead or require a longer
one a charge will be made. It is strongly advised that this
work is carried out by a qualified electrician.
- If the domestic wiring includes a residual current-operated
circuit breaker, ensure that it conforms to the latest
regulations.
the socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised technician to
replace the plug (see Assistance); do not use extension
cables or multiple sockets.
Once the appliance has been installed, the power
supply cable and the electrical socket should be easily
accessible.
The dishwasher must not be connected to the
electricity supply while installation is being carried out.
- This appliance should only be connected to a 230/240V
AC source, via a properly installed earthed socket.
- Use the dishwasher solely in a domestic environment.
- DO NOT stand or place heavy objects on the door when it
is open, this could damage the door or cause the appliance
to tip forward.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be
replaced by the manufacturer or its Technical Assistance
Service in order to prevent all potential hazards. (See
Assistance)
The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
This appliance must be earthed
Fuses:your appliance comes fitted with a plug and a 13A
fuse. If you need to replace the fuse, only those rated at
13A and ASTA approved to BS1362 should be used. If you
lose the fuse cover, a replacement may be obtained from
your local authorised Service Centre or Electrical company.
Correct replacement is identified by colour coding or the
marking on base of plug.
DO NOT use the plug unless the fuse cover is fitted.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the water supplies
Sink Waste System
Connect the outlet hose (without bending it) to a drain duct
with a minimum diameter of 32 mm.
EN
Connection to the water and electricity supplies should
only be performed by a qualified technician.
The dishwasher should not stand on top of the water
hoses or the electricity supply cable.
Connecting the water inlet hose
The water inlet and outlet hoses and the electricity supply
cable may be positioned towards the right or the left in
order to achieve the best possible installation.
•
To a suitable cold water connection point: before
attaching the hose, run the water until it is perfectly clear
so that any impurities that may be present in the water
do not clog the appliance; after performing this
operation, screw the inlet hose tightly onto a tap with a
¾ gas threaded connection.
The outlet hose must be at a height ranging from 40 to 80
cm (from 15’’ to 31’’) from the floor / surface where the
dishwasher rests (A).
•
before connecting the drain hose, remove any internal
restrictions; this will prevent a build up of debris which
could cause a blockage
•
To a suitable hot water connection point: your
dishwasher may be provided with hot water from the
mains supply (if you have a central heating system with
radiators) provided that it does not exceed a temperature
of 60°C.
•
remove any restrictions from the waste spigot and ensure
that the sealing bung is removed (B).
Screw the hose to the tap as described for connection
to a cold water supply.
It MUST NOT be connected to a surface water drain.
If the inlet hose is not long enough, contact a specialist
store or an authorised technician (see Assistance).
• Untie the end of the GREY drainage hose from the rear of
the appliance.
The water pressure must be within the values indicated
in the Technical data table (see Installation).
• Reposition the ‘Hooked End Support’ as required along
the GREY drainage hose.
The hose should not be bent or compressed.
•
If fitting an under sink
waste disposal unit, cut out
the membrane, bung or
blanking plug.
The appliance must be connected to the water supply
network using new hoses.
Do not use old hoses.
Ensure that the new hose supplied is connected and the
old hose is disposed of safely.
DO NOT overtighten the hose connector, hand tight is
sufficient.
Ensure the drain hose is securely attached, to
prevent it coming away while the machine is in use and
causing a flood.
Ensure the fill hose is not kinked.
Fit hose to waste securely using a “Jubilee” type
clip.
Tap connections*: A range of adaptors are available to
suit your tap.
DO NOT connect the dishwasher to a single outlet
instantaneous water heater or an electric heater.
* Only available in selected models.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Anti-flooding protection*
EN
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water
supply in the event of anomalies or leaks from inside the
appliance.
Some models are also equipped with the supplementary
safety device New Acqua Stop*, which guarantees anti-
flooding protection even in the event of a supply hose
rupture.
WARNING: HAZARDOUS VOLTAGE!
Under no circumstance should the water inlet hose be cut
as it contains live electrical parts.
The Company shall not be held responsible for any
incidents that occur if these regulations are not observed.
ECODESIGN REGULATION
ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with a
normal soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce
consumption even further, only run the dishwasher when it is full.
Standby consumption: Left-on mode consumption: 3 W – Off mode consumption: 1,3 W
Consumption data table for the main cycles
Standard conditions*
User conditions**
Energy consumption
(kWh/cycle)
1,65
Water consumption
(l/cycle)
16
16
Duration
(min/cycle)
150
Energy consumption
(kWh/cycle)
1,45
Water consumption
(l/cycle)
15
15
Duration
(min/cycle)
135
INTENSIVE
NORMAL
1,35
120
1,20
110
* Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.
** Data is obtained by recording values when the appliance is operational and loaded with user crockery.
* Only available in selected models.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the appliance
Overall view
EN
1.
Upper rack
2.
3.
4.
5.
Upper sprayer arm
Tip-up compartments
Rack height adjuster
Lower rack
6.
7.
Lower sprayer arm
Cutlery basket
8.
Washing filter
9.
Salt dispenser
10.
11.
12.
Detergent and rinse aid dispensers
Data plate
Control panel***
Control panel
Low rinse aid
indicator light*
Wash cycle number
light-up indicator
Select wash
cycle button
ON/OFF
indicator light
Delayed start button*
ON/OFF/Reset
button
Low salt
Delayed start
indicator lights*
indicator light*
***Only in completely built-in models.
* Only available in selected models.
The number and type of wash cycles and options may vary depending on the dishwasher model.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the racks
Upper rack
Load this rack with delicate and lightweight crockery: glasses,
cups, saucers and shallow salad bowls.
Before loading the racks, remove all food residue from
crockery and empty liquids from glasses and cups.
After loading the appliance, make sure that the sprayer arms
can rotate freely.
EN
Lower rack and cutlery basket
The lower rack can hold pans, lids, plates, salad bowls, cutlery, etc.
Large plates and lids should ideally be placed at the sides of the rack.
Adjustable position tip-up compartments
The tip-up compartments
can be positioned at
different heights, to optimise
the arrangement of
crockery throughout the
rack. Wine glasses can be
placed safely in the tip-up
compartments, by inserting
the stem of each glass into
the
Several dishwasher models are fitted with tip-up sections*, which
can be used in a vertical position when arranging plates or in a
horizontal position when arranging saucepans, salad bowls and
frying pans.
corresponding slots.
Adjusting the height of the upper rack
In order to make it easier to arrange the crockery, the upper rack
may be moved to a higher or lower level.
The height of the upper rack should ideally be adjusted
WHEN THE RACK IS EMPTY.
The type of cutlery basket may vary (modular or non-modular)
according to the dishwasher model. The non-modular basket
must only be positioned at the front of the lower rack.
NEVER raise or lower the rack on one side only.
Open the left and right guide rail stops
and pull out the rack; position it higher or
lower as required, slide it along the guide
rails until the front wheels are in place and
close the stops (see figure).
If the rack is fitted with Dual Space
handles*(see figure), pull out the upper
rack until it reaches its stop point, grip
the handles at the sides of the rack and
move it upwards or downwards, then
slowly let it fall back into place.
Both are fitted with
grilles over the top,
for improved cut-
lery arrangement.
Items that should not be washed in the dishwasher
Knives and other utensils with sharp edges must be placed
in the cutlery basket with the points facing downwards, or they
must be positioned horizontally in the tip-up compartments on the
upper rack.
•
Wooden items, objects with wooden or horn handles or glued-
on parts.
•
•
•
•
Items made from aluminium, copper, brass, pewter or tin.
Items made from plastic material which is not heat-resistant.
Antique or hand-painted porcelain.
Antique silver. Silver that is not antique may, however, be
washed in the dishwasher using a delicate wash cycle,
provided that it does not come into contact with other metals.
We recommend the use of crockery which is dishwasher
safe.
* Only available in selected models. The number and position
may vary.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Start-up and use
Starting the dishwasher
Measuring out the detergent
EN
A good wash result also depends on the correct
amount of detergent being used; exceeding the
stated amount does not result in a more effective
wash and increases environmental pollution.
1. Turn the water tap on.
2. Open the door and press the ON/OFF button: you will
hear a short beep and the display and option indicator
lights switch on.
3. Measure out the detergent (see below).
4. Load the racks (see Loading the racks).
5. Select the wash cycle in accordance with the type of
crockery and its soil level (see Table of wash cycles), by
pressing the P button.
6. Select the wash options* (see adjacent information).
7. Start the wash cycle by shutting the door: a long beep
signals the start of the wash cycle.
Only use detergent which has been specifically
designed for dishwashers.
DO NOT USE washing up liquid.
Using excessive detergent may result in foam
residue remaining in the machine after the cycle has
ended.
8. Two short beeps and one long one indicate the end of
the wash cycle and the wash cycle number flashes on the
display. Open the door, switch off the appliance by pressing
the ON/OFF button, shut off the water tap and unplug the
appliance from the electricity socket.
9. Wait for a few minutes before removing the crockery, in
order to avoid burns. Unload the racks, beginning with the
lower level.
The use of tablets is only recommended for
models which offer the MULTI-FUNCTIONAL
TABLETS option.
To achieve the best results from each washing
and drying cycle, powder detergent, rinse aid liquid
and salt should be used.
Compartment A: Washing detergent
Compartment B: Pre-wash detergent
- The machine will switch off automatically during
certain periods of inactivity, in order to minimise
electricity consumption.
1. Open cover C by pressing
button D.
2. Pour in the detergent after
consulting the Table of wash
cycles:
• For powder detergent use
compartments A and B.
AUTO WASH CYCLES*: this model of dishwasher is
equipped with a special sensor which can be used to
assess the level of soiling and automatically select the most
efficient and economic wash cycle accordingly.
The duration of the auto wash cycles may vary due to the
operation of the sensor.
• For detergent in tablet form:
when the cycle requires 1 tablet,
place it in compartment A and
close the cover; when it requires 2, place the second tablet
at the bottom of the appliance.
Modifying a wash cycle in progress
If a mistake was made during the wash cycle selection
process it is possible to change the cycle, provided that it
has only just begun: open the door, avoiding the escaping
steam, and press and hold the ON/OFF button; the machine
will switch off with a long beep. Switch the machine back
on using the ON/OFF button and select the new wash cycle
and any options desired; start the cycle by closing the door.
3. Remove detergent residues from the edges of the
compartment and close the cover until it clicks.
Adding extra crockery
Without switching off the machine, open the door, taking
care to avoid the escaping steam, and place the crockery
inside the dishwasher. Close the door: the cycle starts from
the point at which it was interrupted.
Accidental interruptions
If the door is opened during the wash cycle, or if there is a
power cut, the cycle stops. It starts again from the point at
which it was interrupted once the door has been shut or
once the electricity supply is restored.
*Only available in selected models.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash options
EN
If an option is not compatible with the selected was
cycle (see Table of wash cycles), the corresponding
LED flashes rapidly 3 times and 2 short beeps will
sound.
Delayed start
It is possible to delay the start time of the cycle by 3, 6 or 9
hours.
1. Press the DELAYED START button: every time it is pressed
a buzzer sounds and the selected period of time is
displayed.
2. Select the wash cycle and shut the door: after the beep
sounds, the timer begins counting down.
3. Once this time has elapsed, the indicator light switches
off and the wash cycle begins.
To adjust the delay time and select a smaller period of time,
press the DELAYED START button. To cancel it, press the
button repeatedly until the selected delayed start indicator
light switches off. The wash cycle will start automatically
as soon as the door is shut.
*Only available in selected models.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash cycles
If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher,
reduce the amount of detergent used accordingly.
EN
The number and type of wash cycles and options may vary depending on the dishwasher model.
Detergent
(A) = compartment A
(B) = compartment B
Wash
cycles
which
include
drying
Wash cycle
duration
(tolerance
±10%)
Wash cycle selection instructions
Wash cycle
Options
Delay
Powder
Liquid
Tablets
Hrs. Min.
Environmentally-friendly wash cycle
with low energy consumption levels,
suitable for pans and dishes.
29 g (A)
6 g (B)
29 ml (A)
6 ml (B)
1 (A)
1 (A)
Yes
Yes
2:55’
1:50’
1. Eco*
Normally soiled pans and dishes.
Standard daily wash cycle.
29 g (A)
6 g (B)
29 ml (A)
6 ml (B)
Delay
2. Auto
Normal Wash
Limited quantity of daily soiling.
(4 place settings + 1 saucepan +1
frying pan).
25 g (A)
25 ml (A)
1 (A)
No
No
No
Delay
Delay
1:00’
0:08’
3. Daily A 60’
4. Soak
Pre-wash for dishes while awaiting
completion of the load with the dishes
from the next meal.
No
No
Heavily soiled dishes and pans (not to
be used for delicate items).
35 g (A)
25 g (A)
35 g (A)
35 ml (A)
25 ml (A)
35 ml (A)
1 (A)
1 (A)
1 (A)
Yes
No
Delay
Delay
Delay
2:25’
0:35’
1:30’
5. Auto
Intensive
Economic and fast wash to be used
for lightly soiled dishes. (Run cycle
immediately after use) (2 plates + 2
glasses + 4 pieces of cutlery + 1
saucepan + 1 small frying pan).
6. Rapid
Economic and fast wash for delicate
items which are sensitive to high
temperatures. (Run cycle immediately
after use) (glasses upper rack +
delicate plates lower rack).
Yes
Yes
7. Crystal
Wash spread over the two racks:
delicate for crystal and glasses on the
upper rack and heavy duty for the
pans on the lower rack.
8. Auto
Duo Wash
35 g (A)
35 ml (A)
1 (A)
Delay
1:45’
Notes:
To make it easier to measure out the detergent, it is worth remembering that:
1 tablespoon = 15 gr. of powder = approximately 15 ml of liquid - 1 teaspoon = 5 gr. of powder = approximately 5 ml of liquid
Optimum performance levels when using the "Daily and Speed/Rapid’" cycle can be achieved by observing the maximum amounts of
crockery specified.
* The Eco wash cycle adheres to the regulation EN-50242. Although it has a longer duration than other wash cycles it uses less
energy and is les harmful to the environment.
Note for Test Laboratories: for information relating to comparative EN testing conditions, please send an email to the
following address: ASSISTENZA_EN_LVS@indesitcompany.com
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Rinse aid and refined salt
- Press the P button repeatedly until the desired hardness level
Only use products which have been specifically
designed for dishwashers.
Do not use table salt or industrial salt, or washing
up liquid.
EN
has been reached (1-2-3-4-5*see Water hardness table).
- To exit the function, wait approximately few seconds or press
another option*button, or switch off the machine using the ON/
OFF button.
Follow the instructions given on the packaging.
Even if using multi-functional tablets, the salt dispenser should
still be filled.
If using a multi-functional product it is not necessary to add
rinse aid; however, we recommend that you add salt, especially
if you live in an area where the water is hard or very hard.
Follow the instructions given on the packaging.
Average salt container
Water Hardness Table
capacity duration**
Level
°dH
°fH
mmol/l
0 - 1
1,1 - 2
2,1 - 3
3,1 - 6
months
7 months
5 months
3 months
2 months
If you do not add salt or rinse aid, the LOW SALT*
and LOW RINSE AID* indicator lights remain lit.
1
0 - 6
0 - 10
2
3
4
6 - 11 11 - 20
12 - 17 21 - 30
17 - 34 31 - 60
Measuring out the rinse aid
Rinse aid makes it easier for the crockery to dry, as water runs off
surfaces more readily and therefore does not leave streaks or
marks.
The rinse aid dispenser should be filled:
• When the LOW RINSE AID*indicator light on the control
panel is illuminated;
5*
34 - 50 61 - 90
6,1 - 9
2/3 weeks
For values between 0°f and 10°f, we do not recommend the
use of salt. * this setting may cause a slight increase in the
duration of the cycles. ** for 1 wash cycle per day.
(°dH = hardness measured in German degrees - °f = hardness
measured in French degrees - mmol/l = millimoles per litre)
1. Open the dispenser by turning
the lid (G) in an anticlockwise
direction.
2. Pour in the rinse aid, making sure
it does not overflow from the
dispenser. If this happens, clean
H
Measuring out the refined salt
In order to achieve the best possible results using a wash cycle,
make sure that the dispenser is never empty. Refined salt removes
limescale from the water, thus avoiding the formation of deposits
on crockery.
F
the spill immediately with a dry
The salt dispenser is located in the lower part of the dishwasher
(see Description) and should be filled:
cloth.
G
3. Screw the lid back on.
• When the green float*cannot be seen by simply looking at the
cap of the salt dispenser.
NEVER pour the rinse aid directly
into the appliance tub.
• When the LOW SALT* indicator light on the control panel is
illuminated;
Adjusting the amount of rinse aid
1. Remove the lower rack and unscrew the
container cap (anticlockwise).
2. The first time you do this: fill the water tank
right up to its edge.
If you are not completely satisfied with the drying results, you
may adjust the quantity of rinse aid used. Use a screwdriver to
turn the dosage adjuster (F) to one of the 6 pre-set positions (the
default position is set to 4):
• If there are streaks on the crockery, set the adjustment device
to a lower number (1-3).
• If drops of water remain on the crockery or if there are limescale
marks present after the cycle has finished, set the adjuster to a
higher number (4-6).
3. Position the funnel*(see figure) and fill the
salt container right up to its edge (this should
hold approximately 1 kg); it is not unusual for a little water to leak
out.
4. Remove the funnel*and wipe any salt residue away from the
opening; rinse the cap under running water and then screw it on,
the head facing downwards so as to let the water flow out of the
four cracks which are arranged in a star shape on the lower part
of the cap. (Salt cap with green float*)
Setting the water hardness
Every dishwasher is equipped with a water softener which, by
using refined salt designed especially for this type of appliance,
supplies water without limescale which is then used to wash the
crockery.
It is advisable to perform this procedure every time you add
salt to the container.
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).
This dishwasher offers a setting which helps to reduce pollution
and optimises washing performance in accordance with the water
hardness level in your area. This information can be obtained
from the organisation which supplies your household with water.
- Open the door and switch on the machine by pressing the ON/
OFF button.
When necessary, measure out the salt before a wash cycle
so that any saline solution which has leaked out of the salt dispenser
is removed.
- Press the P button and hold for approximately 5 seconds; two
short beeps will sound and the set hardness number will flash
slowly on the display (the water softening system is set to number
3).
* Only available in selected models.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and maintenance
Clean the water inlet filter at the tap outlet regularly.
- Turn off the water tap.
- Unscrew the end of the water inlet hose, remove the filter
and clean it carefully under running water.
- Replace the filter and screw the water hose back into
position.
Shutting off the water and electricity
supplies
EN
•
Turn off the water tap after every wash cycle to avoid
leaks.
•
Always unplug the appliance when cleaning it and when
performing maintenance work.
Cleaning the filters
Cleaning the dishwasher
The filter assembly consists of three filters which remove
food residues from the washing water and then recirculate
the water. They should be cleaned if you wish to achieve
the best results in every wash.
•
The external surfaces of the machine and the control
panel may be cleaned using a non-abrasive cloth which
has been dampened with water. Do not use solvents or
abrasive products.
Clean the filters regularly.
•
Any marks on the inside of the appliance may be
removed using a cloth dampened with water and a little
vinegar.
The dishwasher should not be used without filters, or if
the filter is loose.
• After several washes, check the filter assembly and if
necessary clean it thoroughly under running water,
using a non-metallic brush and following the instructions
below:
1. Turn the cylindrical filter C in an anti-clockwise
direction and pull it out (fig. 1).
2. Remove the cup filter B by exerting a slight pressure
on the side flaps (fig. 2).
3. Slide out the stainless steel plate filter A (fig. 3).
4. Inspect the trap and remove any food residue. NEVER
REMOVE the wash cycle pump (black detail) (fig. 4).
Preventing unpleasant odours
•
Always keep the door of the appliance ajar in order to
avoid moisture from forming and being trapped inside
the machine.
•
Clean the seals around the door and detergent
dispensers regularly using a damp sponge. This will
avoid food becoming trapped in the seals, which is the
main cause behind the formation of unpleasant odours.
Cleaning the sprayer arms
Food residue may become encrusted onto the sprayer arms
and block the holes used to spray the water. It is therefore
recommended that the arms are checked from time to time
and cleaned with a small non-metallic brush.
The two sprayer arms may both be removed.
B
To remove the upper sprayer arm,
rotate the locking ring in an anti-
clockwise direction.
C
1
2
The upper sprayer arm should be
replaced with the holes facing
upwards.
The lower sprayer arm can be
removed by pressing on the side
tabs and pulling it upwards.
4
3
After cleaning the filters, replace the filter assembly and fix
it in position correctly; this is essential for maintaining the
efficient operation of the dishwasher.
Leaving the machine unused for extended
periods
Cleaning the water inlet filter*
If the water hoses are new or have not been used for an
extended period of time, let the water run to make sure it is
clear and free of impurities before performing the necessary
connections. If this precaution is not taken, the water inlet
could become blocked and damage the dishwasher.
•
Disconnect the appliance from the electricity supply and
shut off the water tap.
•
Leave the door of the appliance ajar.
• When you return, run a wash cycle when the dishwasher
is empty.
* Only available in selected models.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions and advice
The appliance was designed and manufactured in
Saving energy and respecting the
EN
compliance with current international safety standards. The
following information has been provided for safety reasons and
should therefore be read carefully.
environment
Saving water and energy
•
Only start a wash cycle when the dishwasher is full. While
waiting for the dishwasher to be filled, prevent unpleasant
odours with the Soak cycle (see Wash Cycles).
Select a wash cycle that is suited to the type of crockery and
to the soil level of the crockery using the Wash cycle table:
- for dishes with a normal soil level, use the Eco wash cycle,
which guarantees low energy and water consumption levels.
- if the load is smaller than usual activate the Half load*option
(see Start-up and use).
If your electricity supply contract gives details of electricity
saving time bands, run wash cycles during the periods when
a lower tariff is applied. The Delayed start*button (see Start-
up and use) helps you organise the wash cycles accordingly.
General safety
•
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
The appliance was designed for domestic use inside the home
and is not intended for commercial or industrial use.
The appliance must be used by adults only, to wash domestic
crockery according to the instructions in this manual.
The appliance must not be installed outdoors, even in covered
areas. It is extremely dangerous to leave the machine exposed
to rain and storms.
•
•
•
•
•
•
Phosphate-free and chlorine-free detergents
containing enzymes
•
•
•
Do not touch the appliance when barefoot.
When unplugging the appliance always pull the plug from the
mains socket, do not pull on the cable.
We strongly recommend that you use detergents that do not
contain phosphates or chlorine, as these products are
harmful to the environment.
Enzymes provide a particularly effective action at
temperatures around 50°C, and as a result detergents
containing enzymes can be used in conjunction with low-
temperature wash cycles in order to achieve the same results
as a normal 65°C wash cycle.
To avoid wasting detergent, use the product in appropriate
quantities based on the manufacturer’s recommendations,
the hardness of the water and the soil level and quantity of
the crockery. Even if they are biodegradable, detergents
contain substances that may alter the balance of nature.
•
•
The water supply tap must be shut off and the plug should be
removed from the electrical socket before cleaning the
appliance or carrying out any maintenance work.
If the appliance breaks down, do not under any
circumstances touch the internal parts in an attempt to carry
out the repair work yourself.
•
•
•
Never touch the heating element.
Do not lean or sit on the open door of the appliance: this may
cause the appliance to overturn.
•
•
•
The door should not be left open as it may create a dangerous
obstacle.
The packaging material should not be used as a toy: it can
become a choking or suffocation hazard.
If your family includes children:
• DO NOT allow children to play with the appliance or tamper with
its controls.
Recycling & Disposal Information
• Keep detergents and rinse aids away from children.
• Keep children away from the open door of a dishwasher, there
could still be some detergent left inside.
As part of Hotpoint's continued commitment to helping the
environment, Hotpoint reserves the right to use quality recycled
components to keep down customer costs and minimise material
wastage.
Disposal of old electrical appliances
Please dispose of packaging and old appliances carefully.
To minimise risk of injury to children, remove the door, plug and
cut mains cable off flush with the appliance. Dispose of these
parts separately to ensure that the appliance can no longer be
plugged into a mains socket and the door cannot be locked
shut.
The European Directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE), requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must be
collected separately in order to optimise the recovery and
recycling of the materials they contain and reduce the impact on
human health and the environment. The crossed out "wheeled
bin" symbol on the product reminds you of your obligation, that
when you dispose of the appliance it must be separately collected.
Consumers should contact their local authority or retailer for
information concerning the correct disposal of their old appliance.
* Only available in selected models.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance
(see Assistance).
EN
Problem:
Possible causes / Solutions:
The dishwasher does not start or
cannot be controlled
• Switch off the appliance by pressing the ON/OFF button, switch it back on after
approximately one minute and reset the program.
• The appliance has not been plugged in properly.
• The dishwasher door has not been shut properly.
The door won’t close
• The lock was released. Strongly push the door until a “clacking” noise is heard.
No water drains out from the
dishwasher.
• The dishwasher cycle has not yet finished.
• The water inlet hose is bent (see Installation).
• The drain duct is blocked.
• The filter is clogged up with food residues.
The dishwasher makes excessive
noise.
• The dishes are rattling against each other or against the sprayer arms.
• An excessive amount of foam has been produced: the detergent has not been
measured out correctly or it is not suitable for use in dishwashers (see Start-up
and use).
The dishes and glasses are
covered in a white film or
limescale deposits.
• The level of the refined salt is low or the dosage setting is not suited to the
hardness of the water (see Rinse aid and salt).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
The dishes and glasses are
• The rinse aid dosage is too high.
streaked or have a bluish tinge.
The crockery has not been dried
properly.
• A wash cycle without a drying program has been selected.
• The rinse aid has been used up or the dosage is too low (see Rinse aid and
salt).
• The rinse aid dispenser setting is not suitable.
• The crockery is made from non-stick material or plastic.
The dishes are not clean.
• The racks are overloaded (see Loading the racks).
• The crockery has not been arranged well.
• The sprayer arms cannot move freely.
• The wash cycle is too gentle (see Wash cycles).
• An excessive amount of foam has been produced: the detergent has not been
measured out correctly or it is not suitable for use in dishwashers (see Start-up
and use).
• The lid on the rinse aid compartment has not been shut correctly.
• The filter is dirty or blocked (see Care and maintenance).
• The refined salt level is low (see Rinse aid and salt).
The dishwasher does not take any • There is no water in the mains supply.
water in - Tap shut-off alarm
(several short beeps are emitted)
(the ON/OFF indicator light flashes
and the number 6 appears on the
display).
• The water inlet hose is bent (see Installation).
• Turn on the tap and the appliance will start after a few minutes.
• The appliance lock has been activated because no action was taken when the
beeps sounded.
Switch off the appliance using the ON/OFF button, turn on the tap and switch
the appliance back on after 20 seconds by pressing the same button. Re-
program the appliance and restart the wash cycle.
Water inlet hose alarm / Water inlet • Switch off the appliance by pressing the ON/OFF button. Shut off the water tap
filter blocked
to eliminate the risk of flooding and remove the plug from the electrical socket.
Make sure the water inlet filter has not become blocked by impurities (see “Care
and maintenance” chapter).
(the ON/OFF indicator light flashes
and the number 7 appears on the
display).
* Only available in selected models.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
After Sales Service
After Sales Service
Appliance Registration
EN
No one is better placed to care for your Hotpoint
appliance during the course of its working life
than us - the manufacturer.
We want to give you additional benefits of Hotpoint
ownership. To activate your free 5 year parts guarantee
you must register your appliance with us.
UK: 08448 24 24 24
Republic of Ireland: 01 230 0800
Essential Contact Information
Hotpoint Service
We are the largest service team in the country
offering you access to 400 skilled telephone advisors
and 1000 fully qualified engineers on call to ensure
you receive fast, reliable, local service.
Indesit Company UK Ltd. Morley Way, Peterborough,
PE2 9JB
Indesit Company Unit 49 Airways Industrial
Estate,Dublin 17
UK: 08448 224 224
Republic of Ireland: 0818 313 413
Recycling and Disposal Information
Please note: Our advisors will require the
following information:
As part of Hotpoint's continued commitment to helping
the environment, Hotpoint reserves the right to use
quality recycled components to keep down customer
costs and minimise material wastage.
Model number:
Please dispose of packaging and old appliances
carefully.
To minimise risk of injury to children, remove the door,
plug and cut mains cable off flush with the appliance.
Dispose of these parts separately to ensure that the
appliance can no longer be plugged into a mains socket
and the door cannot be locked shut.
Serial number:
Parts and Accessories
We supply a full range of genuine replacement
parts as well as accessory products that protect
and hygienically clean your appliance to keep it
looking good and functioning efficiently throughout
its life.
UK: 08448 225 225
Republic of Ireland: 0818 313 413
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee
195087744.01
03/2012 pb - Xerox Fabriano
Guarantee
EN
12 months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for
twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because
of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to
you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our operating and
maintenance instructions.
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any
person not authorised by us.
-
-
-
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result of improper
installation.
Replacement of any consumable item or accessory. These included but not limited to: plugs, cables,
batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-
DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you
registering your appliance with us and the parts being fitted by one of our authorised engineers. There will be a
charge for our engineer’s time. To activate the extra parts warranty on your appliance, simply call our
registration line on 08448 24 24 24 (Republic of Ireland 01 230 0800)
Extended Guarantees
We offer a selection of protection plans that enable you to fully cover yourself against the expense of
repair bills for the life of your policy. To find the ideal plan for you please call our advice line on 08448 226 226
(Republic of Ireland 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service
Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where necessary, to
arrange for an engineer to call.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
|