SELF-CONTAINED CRESCENT CUBER
KM-61BAH
KM-101BAH
KM-151BAH
KM-151BWH
INSTRUCTION MANUAL
L1M006102 (100109)
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
1. This booklet is an integral and essential part of the product and should
be handed over to the user. Read the warnings contained in this booklet
carefully as they give important indications regarding the safety of the
installation, use and maintenance. Please preserve this booklet for any
further consultation that may be necessary.
2. This icemaker should be destined only to the use for which it has been
expressly conceived. Any other use should be considered improper and
therefore dangerous. The manufacturer cannot be held responsible for
eventual damage caused by improper, incorrect and unreasonable use.
PAGE
CONTENTS
I. Specifications -------------------------------------------------------------------------------------------1
A. Nameplate Rating----------------------------------------------------------------------------------1
B. Dimensions/Connections-------------------------------------------------------------------------2
1. KM-61BAH----------------------------------------------------------------------------------------2
2. KM-101BAH --------------------------------------------------------------------------------------3
3. KM-151BAH --------------------------------------------------------------------------------------4
4. KM-151BWH -------------------------------------------------------------------------------------5
II. Installation and Operating Instructions-----------------------------------------------------------6
A. Checks Before Installation -----------------------------------------------------------------------6
B. How to Remove Panels---------------------------------------------------------------------------6
C. Location ----------------------------------------------------------------------------------------------7
D. Electrical Connection------------------------------------------------------------------------------8
E. Set Up-------------------------------------------------------------------------------------------------8
F. Water Supply and Drain Connections ---------------------------------------------------------9
G. Final Checklist ------------------------------------------------------------------------------------ 12
H. Startup ---------------------------------------------------------------------------------------------- 13
III. Cleaning and Maintenance Instructions ------------------------------------------------------ 14
A. Cleaning -------------------------------------------------------------------------------------------- 14
1. Cleaning Procedure -------------------------------------------------------------------------- 14
2. Sanitizing Procedure - Following Cleaning Procedure ------------------------------ 16
B. Maintenance--------------------------------------------------------------------------------------- 17
1. Exterior Panels -------------------------------------------------------------------------------- 17
2. Storage Bin and Scoop---------------------------------------------------------------------- 17
3. Air Filter------------------------------------------------------------------------------------------ 18
4. Condenser -------------------------------------------------------------------------------------- 18
C. Preparing the Icemaker for Long Storage ------------------------------------------------- 18
Download from Www.Somanuals.com. All Manuals Search And Download.
I. Specifications
A. Nameplate Rating
Model
Amperes
Refrigerant
R134a 7.1 oz.
R134a 7.8 oz.
R134a 8.5 oz.
R134a 10.3 oz.
ARI
Energy Star
Not applicable
Applicable
Applicable
Not applicable
KM-61BAH
KM-101BAH
KM-151BAH
KM-151BWH
3.4 AMPS
5.2 AMPS
7.0 AMPS
7.0 AMPS
Not applicable
Applicable
Applicable
Applicable
See the Nameplate for electrical and refrigeration specifications. This Nameplate is
located on the upper part of the Left Side Panel.
We reserve the right to make changes in specifications and design without prior notice.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Dimensions/Connections
1. KM-61BAH
Unit:
2
Download from Www.Somanuals.com. All Manuals Search And Download.
2. KM-101BAH
Unit: mm [inches]
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. KM-151BAH
Unit: mm [inches]
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. KM-151BWH
Unit: mm [inches]
5
Download from Www.Somanuals.com. All Manuals Search And Download.
II. Installation and Operating Instructions
A. Checks Before Installation
* Visually inspect the exterior of the shipping container, and any severe damage noted
should be reported to the carrier.
IMPORTANT
1. Remove shipping carton, tape(s) and packing. If packing material is left in
the icemaker, it will not work properly.
2. Ensure all components, fasteners and thumbscrews are securely in place.
3. Remove the shipping tapes holding the Door and Separator. See Fig. 1.
1) Remove the panels to prevent damage when installing the icemaker. (See “B. How to
Remove Panels”.)
2) Remove the package containing accessories.
3) Remove the protective plastic film from the panels. If the icemaker is exposed to the
sun or to heat, remove the film after the icemaker cools.
4) Check that refrigerant lines do not rub or touch lines or other surfaces, and that the fan
blade turns freely.
5) Check that the Compressor is snug on all mounting pads.
6) See the Nameplate on the upper part of the Left Side Panel, and check that your voltage
supplied corresponds with the voltage specified on the Nameplate.
- See Fig. 1
B. How to Remove Panels
* Louver:
Remove the Air Filter. Lift it up and towards you.
Push down snap tabs at the top on both sides by a flat head screwdriver,
pull towards you slightly, and lift off.
* Top Panel:
Remove the screws. Slide rearward, and lift off.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
l
Separator
Storage Bin
Top Panel Tab
(both ends)
Door
Control Switch
Air Filter
Louver Tab
(both ends)
Louver
Fig. 1
C. Location
WARNING
This icemaker is not intended for outdoor use. Normal operating ambient
temperature should be within +45°F to +100°F (+7°C to +38°C); Normal
operating water temperature should be within +45°F to +90°F (+7°C to +32°
C). Operation of the icemaker, for extended periods, outside of these normal
temperature ranges may affect production capacity.
For best operating results:
* The icemaker should not be located next to ovens, grills or other high heat producing
equipment.
* Level the icemaker from side to side and front to rear by adjusting the legs. The location
should provide a firm and level foundation for the equipment.
* Avoid a site where dripping is not allowed.
* This icemaker will not work at subfreezing temperatures. To prevent damage to the water
supply line, drain the icemaker when air temperature is below zero.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
* The icemaker requires no clearance at either side. But allow enough space at rear for
water supply and drain connections, at least 12” (approx. 30 cm) clearance at front, and
at least 0.6” (approx. 15 mm) clearance at top for maintenance.
D. Electrical Connection
WARNING
THIS APPLIANCE MUST BE GROUNDED.
This icemaker requires a ground that meets the national and local electrical
code requirements. To prevent possible severe electrical shock injury to
individuals or extensive damage to equipment, install a proper ground wire
to this icemaker. Remove the plug from the electrical outlet before any
maintenance, repairs or cleaning is undertaken.
CAUTION
The GREEN ground wire in the factory-installed power cord is connected to
a screw on the bracket where the cord enters the machine. If it becomes
necessary to remove or replace the power cord, be sure to connect the power
cord’s ground wire to this screw upon reattachment.
* This icemaker must be plugged into an independent power receptacle which has enough
capacity. The maximum allowable voltage variation should not exceed 10 percent of the
nameplate rating. See the Nameplate.
* Usually an electrical permit and services of a licensed electrician are required.
E. Set Up
IMPORTANT
Do not place heavy objects exceeding 33 lbs (15 kg) on the Top Panel.
1) Unpack the icemaker, and remove all shipping cartons, tapes and packing BEFORE
operating the unit.
2) Position the icemaker in a selected site. Clean the interior with soap and water and
rinse thoroughly.
3) Level the icemaker in both the left-to-right and the front-to-rear directions (when installed
with or without legs). See Fig. 2.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4) When installing the unit without legs, the perimeter where the machine touches the
counter should be sealed with silicone to prevent water from leaking under the icemaker.
5) When installing the unit with legs on the bottom, use the four accessory legs adjustable
from 6” (15.2 cm) to 7” (17.8 cm). Screw the legs tightly into the tapped holes in the
base (see Fig. 3). Handle the icemaker carefully not to damage the exterior.
Tapped Hole
(Leg Mounting)
Base
Adjustable Leg
Fig. 2
Fig. 3
- See Fig. 4
F. Water Supply and Drain Connections
CAUTION
To prevent damage to equipment, do not operate this icemaker when the
water supply is OFF, or if the pressure is below 10 PSIG (0.7 bar). Do not run
the icemaker until proper water pressure is reached.
* Water supply inlet is 1/2” female pipe thread (FPT).
* A water supply line shut-off valve and drain valve should be installed. A minimum of 3/8”
OD copper tubing is recommended for the water supply lines.
* Water supply pressure should be a minimum of 10 PSIG (0.7 bar) and a maximum of
113 PSIG (7.5 bar). If the pressure exceeds 113 PSIG (7.5 bar), the use of a pressure
reducing valve is required.
* Drain outlet for icemaker dump is 3/4” FPT.
* Drain lines must have 1/4” fall per foot (2 cm per meter) on horizontal runs to get good
flow. A vented tee connection is also required for proper flow.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
* Drain lines should not be piped directly
to the sewer system. An air gap of a
minimum of 2 vertical inches (5 cm)
should be between the end of the drain
pipes from the icemaker and the floor
drain.
KM-61BAH, KM-101BAH, KM-151BAH
* This icemaker should be installed in
accordance with applicable national,
state and local regulations.
* A plumbing permit and services of a
licensed plumber may be required in
some areas.
Drain Outlet
3/4” FPT
Water Supply Inlet
1/2” FPT
Fig. 4
10
Download from Www.Somanuals.com. All Manuals Search And Download.
KM-151BWH
Bin Drain Outlet
3/4” FPT
Condenser Water
Outlet 1/2” FPT
Condenser Water
Inlet 1/2” FPT
Icemaking Water Supply
Inlet 1/2” FPT
Shut-off Valve
Two-inch (5 cm)
air gap
Drain Valve
Separate piping to approved drain.
Leave a two-inch (5 cm) vertical air
gap between the end of each pipe
and the drain.
Drain Valve
Shut-off Valve
Floor
Drain
Fig. 5
11
Download from Www.Somanuals.com. All Manuals Search And Download.
G. Final Checklist
1) Is the icemaker level?
2) Is the icemaker in a site where the ambient temperature is within +45°F to +100°F (+7°
C to +38°C) and the water temperature within +45°F to +90°F (+7°C to +32°C) all year
around?
3) Is there at least 0.6” (15 mm) clearance at top of the icemaker for ease of maintenance
or service?
4) Have all shipping carton, tape(s) and packing been removed from the icemaker? Is the
cube guide in its correct position?
5) Are all components, fasteners and screws securely in place?
6) Have all electrical and piping connections been made?
7) Has the power supply voltage been checked or tested against the nameplate rating?
And has a proper ground been installed in the icemaker?
8) Are the water supply line Shut-off Valve and Drain Valve installed? Has the water
supply pressure been checked to ensure a minimum of 10 PSIG (0.7 bar) and a
maximum of 113 PSIG (7.5 bar)?
Note: The icemaker may stop running when the water supply is OFF, or if the pressure
is below 10 PSIG (0.7 bar). When the proper water pressure is reached, the
icemaker automatically starts running again.
9) Have the Compressor hold-down bolts and all refrigerant lines been checked against
vibration and possible failure?
10) Has the bin control operation been verified?
11) Has the end user been given the Instruction Manual and instructed on how to operate
the icemaker and the importance of the recommended periodic maintenance?
12) Has the end user been given the name and telephone number of an authorized service
agent?
13) Has the warranty card been filled out and forwarded to the factory for warranty
registration?
12
Download from Www.Somanuals.com. All Manuals Search And Download.
H. Startup
CAUTION
1. All parts are factory-adjusted. Improper adjustments may result in failure.
2. If the unit is turned off, wait for at least 3 minutes before restarting the
icemaker to prevent damage to the Compressor.
* Check that shipping tape(s), string and packing are removed before starting the icemaker.
1) Open the Water Supply Line Shut-off Valve.
2) Remove the Air Filter.
3) Move the Control Switch on the Control Box to the “ICE” position.
4) Let the icemaker run for 10 minutes, then move the Control Switch to the “OFF”
position.
5) Open the Door.
6) Disconnect the Silicone Hose to drain the water. See Fig. 6.
7) Reconnect the Silicone Hose back in its correct position after all of the water has
drained.
8) Clean inside the Storage Bin and Door.
9) Move the Control Switch to the “ICE” position. This starts the automatic icemaking
process.
10) Close the Door.
Cube Guide
11) Place the Air Filter in its
correct position.
Water Tank
Silicone Hose
(Connect/disconnect
arrowed part)
Overflow Pipe
(Disconnect from tank
bottom)
Storage Bin
Fig. 6
13
Download from Www.Somanuals.com. All Manuals Search And Download.
III. Cleaning and Maintenance Instructions
IMPORTANT
Ensure all components, fasteners and screws are securely in place after any
maintenance or cleaning is done to the equipment.
A. Cleaning
WARNING
1. Hoshizaki recommends cleaning this unit at least once a year. More
frequent cleaning, however, may be required in some existing water
conditions.
2. To prevent injury to individuals and damage to the icemaker, do not use
ammonia type cleaners.
3. Always wear liquid-proof gloves to prevent the cleaning and sanitizing
solutions from coming into contact with skin.
4. For safety and maximum effectiveness, use cleaning and sanitizing
solutions immediately after dilution.
1. Cleaning Procedure
1) Dilute 5 fl. oz. (148 ml) of recommended cleaner Hoshizaki “Scale Away” or “LIME-A-
WAY” (Economics Laboratory, Inc.) with 1 gallon (3.8 lit.) of water.
2) Remove the Air Filter. Remove all ice from the Evaporator and the Storage Bin.
Note: To remove cubes on the Evaporator, move the Control Switch on the Control Box
to the “OFF” position and move it back to the “ICE” position after 3 minutes. The
defrost cycle starts and the cubes will be removed from the Evaporator.
3) Move the Control Switch to the “OFF” position. Open the Door.
4) Disconnect the Silicone Hose to drain the water. See Fig. 6. Reconnect the Silicone
Hose back in its correct position after all of the water has drained.
5) Pour the cleaning solution into the Water Tank. Move the Control Switch to the “WASH”
position. Close the Door.
6) After 30 minutes, move the Control Switch to the “OFF” position.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
7) Same as step 4.
8) Move the Control Switch to the “ICE” position to fill the Water Tank with water.
9) After 3 minutes, move the Control Switch to the “WASH” position.
10) After 5 minutes, move the Control Switch to the “OFF” position.
11) Same as step 4.
12) Repeat steps 8 through 11 three more times to rinse thoroughly.
13) Disconnect the Silicone Hose and Overflow Pipe. Next, remove the Water Tank by
pressing down on the snaps on the Bracket (L) (R) and pulling the tank towards you
slightly and pushing it down. Be careful to avoid breakage when handling the parts.
See Fig. 7.
Pump Motor
Bracket (L)
Bracket (R)
Push
Evaporator
Snap
(both ends)
Float Switch
Cube Guide
Water Tank
* This illustration shows KM-61BAH. The Float Switch location
is different for KM-151BAH/BWH (behind the Pump Motor).
Fig. 7
14) Pull the Cube Guides (quantity varies depending on model) upward to remove them
from the Water Tank. They are snapped in place. See Fig. 8.
15) Same as step 1.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Cube Guide
Water Tank
Snap
* This illustration shows KM-61BAH.
The following number of Cube
Guides are provided:
KM-61BAH
2 pcs
KM-101BAH 3 pcs
KM-151BAH 3 pcs
KM-151BWH 3 pcs
* The Bin Control Switch is accessible by
removing the Water Tank. Pull the switch
towards you for easy maintenance.
* This is the front view with the Door opened
and the Water Tank removed.
Bin Control Switch
Fig. 8
16) Wash the Bin Control Switch, Water Tank, Float Switch, Cube Guide, Silicone Hose
and Overflow Pipe by using a nylon scouring pad, brushes and the cleaning solution.
In addition to the removed parts, also wash the bin liner and Bracket (L) (R) with the
solution.
17) Discard the cleaning solution and rinse the parts thoroughly with water.
2. Sanitizing Procedure - Following Cleaning Procedure
1) Dilute approximately 0.5 fl. oz. (15 ml or 1 tbs) of a 5.25% sodium hypochlorite solution
(chlorine bleach) with 1 gallon (3.8 lit.) of warm water. Using a chlorine test strip or
other method, confirm that you have a concentration of about 200 ppm.
2) Soak the removed parts from step 16 above in a clean container containing the
sanitizing solution. After allowing the parts to soak for 10 minutes, wash them with the
solution. Also wash the bin liner, Bracket (L) (R) with the solution.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Discard the sanitizing solution and rinse the parts thoroughly with water.
4) Replace the removed parts in their correct positions in the reverse order of which they
were removed.
5) Same as step 1.
6) Pour the sanitizing solution into the Water Tank, and allow the sanitizer to sit for 10
minutes.
7) Move the Control Switch to the “WASH” position. Close the Door.
8) After 15 minutes, move the Control Switch to the “OFF” position. Open the Door.
9) Disconnect the Silicone Hose to drain the water. Reconnect the Silicone Hose back in
its correct position after all of the water has drained.
10) Repeat steps 5 through 9 one time. Repeat steps 8 through 11 in the Cleaning
Procedure three times to rinse thoroughly.
11) Flush the Storage Bin with water.
12) Move the Control Switch to the “ICE” position, and start the automatic icemaking
process.
13) Close the Door. Replace the Air Filter in its correct position.
B. Maintenance
1. Exterior Panels
To prevent corrosion, wipe the exterior occasionally with a clean and soft cloth. Use a
damp cloth containing a neutral cleaner to wipe off all oil or dirt build up.
2. Storage Bin and Scoop
* Wash your hands before removing ice. Use the plastic scoop provided (Accessory).
* The Storage Bin is for ice use only. Do not store anything else in the bin.
* Keep the scoop clean. Clean it by using a neutral cleaner and rinse thoroughly.
* Clean the bin liner by using a neutral cleaner. Rinse thoroughly after cleaning.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Air Filter
The plastic mesh Air Filter removes dirt or dust from the air, and keeps the Condenser from
getting clogged. As the filter gets clogged, the icemaker’s performance will be reduced.
Check the filter at least twice a month. When it is clogged, use warm water and a neutral
cleaner to wash the filter.
4. Condenser
Check the Condenser once a year, and clean if required by using a brush or vacuum
cleaner. More frequent cleaning may be required depending on the location of the
icemaker.
C. Preparing the Icemaker for Long Storage
IMPORTANT
When shutting off the icemaker for an extended time, drain out all water from
the water lines and remove the ice from the Storage Bin. The Storage Bin
should be cleaned and dried. Drain the icemaker using air or carbon dioxide
to prevent damage to the water supply lines at sub-freezing temperatures.
Shut off the icemaker until the proper ambient temperature is resumed.
When the icemaker is not used for two or three days, it is sufficient to only move
the Control Switch to the “OFF” position, unless the icemaker will be at sub-freezing
temperatures.
1. Remove the water from the potable water supply line:
1) Remove the Air Filter if it has not already been removed.
2) Move the Control Switch on the Control Box to the “OFF” position.
3) Wait 3 minutes.
4) Close the potable water supply line Shut-off Valve and open the potable water supply
line Drain Valve. See Figs. 4 and 5.
5) Allow the line to drain by gravity.
6) Attach compressed air or carbon dioxide supply to the potable water supply line Drain
Valve.
7) Move the Control Switch to the “ICE” position.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
8) Quickly blow the potable water supply line out using compressed air or carbon dioxide.
2. Drain the potable Water Tank:
1) Turn off the power supply at the breaker box.
2) Move the Control Switch on the Control Box to the “OFF” position.
3) Open the Door. Disconnect the Silicone Hose to drain the water. See Fig. 6.
4) Reconnect the Silicone Hose back in its correct position after all of the water has
drained.
5) Remove all ice from the Storage Bin and clean the Storage Bin.
6) Close the Door.
7) Place the Air Filter in its correct position.
8) Close the potable water supply line Drain Valve.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
|