Hoshizaki America, Inc.
Hoshizaki
Self-Contained Cubelet
Models
C-101BAH
C-101BAH-DS
C-101BAH-AD
C-101BAH-ADDS
INSTRUCTION MANUAL
“A Superior Degree
of Reliability”
Issued: 7-25-2013
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
This manual should be read carefully before the appliance is installed and operated.
Read the warnings and guidelines contained in this manual carefully as they
provide essential information for the continued safe use and maintenance of the
appliance. Retain this manual for any further reference that may be necessary.
CONTENTS
Important Safety Information ................................................................................................. 4
I. Specifications...................................................................................................................... 6
A. Construction.................................................................................................................. 6
B. Electrical and Refrigerant Data ..................................................................................... 6
C. Dimensions/Connections .............................................................................................. 7
1. C-101BAH ................................................................................................................. 7
2. C-101BAH-DS........................................................................................................... 8
3. C-101BAH-AD........................................................................................................... 9
4. C-101BAH-ADDS.................................................................................................... 10
II. Installation Instructions .....................................................................................................11
A. Checks Before Installation............................................................................................11
B. Location........................................................................................................................11
1. General ....................................................................................................................11
2. Built-In Installation Site........................................................................................... 12
C. Door ............................................................................................................................ 13
1. C-101BAH, C-101BAH-AD ...................................................................................... 13
a) Door Reversal.................................................................................................... 13
2. C-101BAH-DS, C-101BAH-ADDS........................................................................... 15
a) Overlay Panel Fabrication and Attachment........................................................ 15
D. Setup........................................................................................................................... 23
E. Electrical Connection .................................................................................................. 23
F. Water Supply and Drain Connections .......................................................................... 24
G. Final Checklist ............................................................................................................ 26
III. Operating Instructions..................................................................................................... 27
A. Important Notes About Usage..................................................................................... 27
B. Startup ........................................................................................................................ 29
IV. Maintenance ................................................................................................................... 30
A. Maintenance Schedule................................................................................................ 31
B. Cleaning and Sanitizing Instructions........................................................................... 32
C. Storage Bin Drain........................................................................................................ 34
D. Condenser................................................................................................................... 35
E. Optional Drain Pump HS-5061.................................................................................... 36
V. Preparing the Appliance for Periods of Non-Use ............................................................. 37
VI. Disposal.......................................................................................................................... 39
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Information
Throughout this manual, notices appear to bring your attention to situations which could
result in death, serious injury, damage to the appliance, or damage to property.
WARNING
NOTICE
IMPORTANT
Indicates a hazardous situation which could result in death or
serious injury.
Indicates a situation which could result in damage to the
appliance or property.
Indicates important information about the installation, use, and
care of the appliance.
WARNING
The appliance should be destined only to the use for which it has been expressly
conceived. Any other use should be considered improper and therefore dangerous. The
manufacturer cannot be held responsible for injury or damage resulting from improper,
incorrect, and unreasonable use. Failure to install, operate, and maintain the appliance
in accordance with this manual will adversely affect safety, performance, component
life, and warranty coverage and may result in costly water damage.
To reduce the risk of death, electric shock, serious injury, or fire, follow basic
precautions including the following:
• Only qualified service technicians should install and service the appliance.
• The appliance must be installed in accordance with applicable national, state, and local
codes and regulations.
• The appliance requires an independent power supply of proper capacity. See the
nameplate for electrical specifications. Failure to use an independent power supply of
proper capacity can result in a tripped breaker, blown fuse, damage to existing wiring,
or component failure. This could lead to heat generation or fire.
• THE APPLIANCE MUST BE GROUNDED: The appliance is equipped with a
NEMA 5-15 three-prong grounding plug
to reduce the risk of potential shock
hazards. It must be plugged into a properly grounded, independent 3-prong wall
outlet. If the outlet is a 2-prong outlet, it is your personal responsibility to have a
qualified electrician replace it with a properly grounded, independent 3-prong wall
outlet. Do not remove the ground prong from the power cord and do not use an
adapter plug. Failure to properly ground the appliance could result in death or serious
injury.
• Do not use an extension cord.
• To reduce the risk of electric shock, do not touch the control switch or plug with damp
hands. Make sure the control switch is in the "OFF" position before plugging in or
unplugging the appliance.
• Do not use an appliance with a damaged power cord. The power cord should not be
altered, jerked, bundled, weighed down, pinched, or tangled. Such actions could result
in electric shock or fire. To unplug the appliance, be sure to pull the plug, not the cord,
and do not jerk the cord.
• Do not make any alterations to the appliance. Alterations could result in electric shock,
injury, fire, or damage to the appliance.
• Do not place fingers or any other objects into the ice discharge opening.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING, continued
• The appliance is not intended for use by persons (including children) with reduced
physical, sensory, or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Young children should be properly supervised around the appliance.
• Do not climb, stand, or hang on the appliance or appliance door or allow children or
animals to do so. Serious injury could occur or the appliance could be damaged.
• Be careful not to pinch fingers when opening and closing the door. Be careful when
opening and closing the door when children are in the area.
• Do not use combustible spray or place volatile or flammable substances near the
appliance. They might catch fire.
• Keep the area around the appliance clean. Dirt, dust, or insects in the appliance could
cause harm to individuals or damage to the appliance.
NOTICE
• Protect the floor when moving the appliance to prevent damage to the floor.
• Follow the water supply, drain connection, and maintenance instructions carefully to
reduce the risk of costly water damage.
• In areas where water damage is a concern, install in a contained area with a floor drain.
• Install the appliance in a location that stays above freezing. Normal operating ambient
temperature must be within 45°F to 100°F (7°C to 38°C).
• If using the optional drain pump (HS-5061), test its operation every time the appliance
is cleaned and sanitized. See "IV.E. Optional Drain Pump HS-5061" for details. If
the optional drain pump is not operating properly, water could back up and overflow,
leading to costly water damage.
• To help ensure the storage bin drain remains clear, follow the instructions in "IV.C.
Storage Bin Drain" once every 3 months or as often as necessary for conditions. If
the storage bin drain becomes clogged, water could build up in the bin and overflow,
leading to costly water damage.
• If water collects in the bin and will not drain, turn off the appliance and close the water
supply line shut-off valve. Call for service.
• If water seeps from the base of the appliance, turn off the appliance and close the
water supply line shut-off valve. Call for service. Failure to do so could lead to costly
water damage.
• Do not leave the appliance on during extended periods of non-use, extended
absences, or in sub-freezing temperatures. To properly prepare the appliance for
these occasions, follow the instructions in "V. Preparing the Appliance for Periods of
Non-Use."
• Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear
of obstruction.
• Do not place objects on top of the appliance.
• The storage bin is for ice use only. Do not store anything else in the storage bin.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
I. Specifications
A. Construction
Top Panel
Ice Discharge
Opening
Bin Control
Thermostat
Bulb
Scoop Holder
Slope
Magnet
Catch
Front Panel
Control Switch
Door
Power Cord
Louver
B. Electrical and Refrigerant Data
The nameplate provides electrical and refrigerant data. The nameplate is located inside the
storage bin. For certification marks, see the nameplate.
We reserve the right to make changes in specifications and design without prior notice.
Model Number
C-101BAH
C-101BAH-DS
C-101BAH-AD
C-101BAH-ADDS
AC Supply Voltage 115-120/60/1
Amperes
4.0 AMPS
Design Pressure
Refrigerant
HI-240PSI LO-120PSI
134a 3.17 OZ.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Dimensions/Connections
1. C-101BAH
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2. C-101BAH-DS
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3. C-101BAH-AD
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4. C-101BAH-ADDS
10
Download from Www.Somanuals.com. All Manuals Search And Download.
II. Installation Instructions
WARNING
• The appliance must be installed in accordance with applicable national, state, and
local codes and regulations.
• CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews
are securely in place after installation. Make sure that none have fallen into the
storage bin.
A. Checks Before Installation
• Visually inspect the exterior of the shipping container and immediately report any
damage to the carrier. Upon opening the container, any concealed damage should also
be immediately reported to the carrier.
• Remove the shipping carton, tape, and packing material. If any are left in the appliance,
it will not work properly.
• Remove the package containing the accessories.
• Remove the protective plastic film from the panels. If the appliance is exposed to the
sun or to heat, remove the film after the appliance cools.
• See the nameplate inside the storage bin, and check that your voltage supplied
corresponds with the voltage specified on the nameplate.
B. Location
1. General
The appliance is approved for indoor or outdoor use.
NOTICE
• Normal operating ambient temperature must be within 45°F to 100°F (7°C to
38°C); Normal operating water temperature must be within 45°F to 90°F (7°C to
32°C). Operation of the appliance, for extended periods, outside of these normal
temperature ranges may affect appliance performance.
• The appliance will not work at sub-freezing temperatures. To prevent damage
to the water supply line, drain the appliance if the air temperature is going to go
below 32°F (0°C). See "V. Preparing the Appliance for Periods of Non-Use."
• The appliance should not be located next to ovens, grills, or other high heat producing
equipment.
• The location must provide a firm and level foundation for the appliance.
• The appliance requires no side or top clearance. But allow enough space at rear for
water supply and drain connections and at least 15" (38 cm) clearance at front.
• The appliance must be at floor level on a finished floor even if under a cabinet. In areas
where water damage is a concern, install in a contained area with a floor drain.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Built-In Installation Site
NOTICE
• Do not let the weight of the counter rest on the appliance.
• Do not install the appliance in a corner where the door will interfere with other
equipment or where the appliance cannot be pulled out for service.
Installation Space
Model
C-101BAH
C-101BAH-DS
Height
Width
Depth
34" (864 mm) minimum
15" (381 mm) minimum 24" (610 mm) minimum
C-101BAH-AD
C-101BAH-ADDS
32" (814 mm) minimum
Between Two Cabinets
Between a Cabinet and
the End of a Counter
C-101BAH
C-101BAH
C-101BAH-DS
C-101BAH-DS
Min. 34"
Min. 15"
(381 mm)
Min. 15"
(381 mm)
Support: Do not
let the weight
of the counter
rest on the
Min. 34"
(864 mm)
C-101BAH-AD
C-101BAH-ADDS
Min. 32"
(864 mm)
C-101BAH-AD
C-101BAH-ADDS
Min. 32"
appliance
(814 mm)
(814 mm)
In a Corner
Between a Cabinet and
a Wall or Tall Cabinet
Secure: Do not
let the weight
of the counter
rest on the
Oven
Appliance
appliance
12
Download from Www.Somanuals.com. All Manuals Search And Download.
C. Door
1. C-101BAH, C-101BAH-AD
a) Door Reversal
If you would like to reverse the door swing, follow the steps below. Otherwise, skip to
section "II.D. Setup."
1) While maintaining a hold on the door, remove the hinge stop pin from hinge (B). Pull out
the bottom of the door slightly and gently remove the door from hinge (A). See Fig. 1.
Hinge (B)
Hinge (A)
Fig. 1
Hinge Stop Pin
2) Remove the 2 bolts securing the top panel, then lift it off. See Fig. 2.
Bolts
Top Panel
Fig. 2
3) Remove hinge (A) and the bracket from the right side of the appliance and the top brace
from the left side. Rotate hinge (A) to position the gasket notch to the inside, then fasten
hinge (A) and the bracket to the left side and the top brace to the right side. See Fig. 3.
Screw
Bracket
Hinge (A)
Screw
Fig. 3
Top Brace
Gasket Notch
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4) Remove hinge (B) from the right side of the appliance and the 2 filler screws from the
left side. Attach the 2 filler screws to the right side and attach hinge (B) to the left side.
See Fig. 4.
5) Rotate the top panel 180° from its previous position. This brings the notch that was
previously in the right rear to the left front. See Fig. 5. Hook the rear part of the panel on
the body, then secure the front with the 2 bolts removed in step 2.
Top Panel
Screws
Notch
Hinge (B)
Filler
Screws
Fig. 4
Fig. 5
6) Remove the 2 screws attaching the door handle and also remove the other 2 screws
indicated in the illustration. Use 2 of the screws to attach the handle to the other side of
the door and attach the other 2 screws in the remaining 2 holes. See Fig. 6.
7) Attach the door to hinge (A), then continue to maintain a hold on the door. Screw the
hinge stop pin into hinge (B) until it is tight. See Fig. 7.
Door Handle
Hinge (B)
Screws
Fig. 6
Hinge Stop Pin
Fig. 7
14
Download from Www.Somanuals.com. All Manuals Search And Download.
2. C-101BAH-DS, C-101BAH-ADDS
a) Overlay Panel Fabrication and Attachment
IMPORTANT
The overlay panel must be crafted by a professional cabinet maker to ensure
quality results.
(1) Parts
Ensure that all parts required for the overlay panel assembly are contained in the
accessories bag.
Overlay Panel Parts
No. Description
Part Number Qty.
1
2
3
4
5
6
Threaded Wood Insert
4A4004-01
7P32-0408
7C12-0425
7C32-0408
4A0629-02
4A3998-01
6
3
4
2
2
1
T2 Screw 4×8 SS
Pan Head Screw M4×25 SS
Truss Head Screw M4×8 SS
Canoe Clip
Sheet Metal Bracket
4
5
1
2
3
6
15
Download from Www.Somanuals.com. All Manuals Search And Download.
(2) Overlay Panel Specification
Use the specification that applies to your appliance (C-101BAH-DS or C-101BAH-ADDS)
and the directions that follow to prepare your overlay panel.
(a) C-101BAH-DS
(
(
)
)
(
)
(
)
C-101BAH-DS Overlay Panel Specification
29 17/32" (750 mm)
Overlay Panel Height
Overlay Panel Width
14 13/16" (376 mm)
Overlay Panel Thickness
Overlay Panel and Door Weight (total)
5/8" (16 mm) minimum; 3/4" (19 mm) maximum
20 lb. (9 kg) maximum
16
Download from Www.Somanuals.com. All Manuals Search And Download.
(b) C-101BAH-ADDS
)
)
(
(
(
)
)
(
C-101BAH-ADDS Overlay Panel Specification
27 9/16" (700 mm)
Overlay Panel Height
Overlay Panel Width
14 13/16" (376 mm)
Overlay Panel Thickness
5/8" (16 mm) minimum; 3/4" (19 mm) maximum
20 lb. (9 kg) maximum
Overlay Panel and Door Weight (total)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
(3) Fabrication of Overlay Panel
Fabricate the overlay panel as outlined in the specification on the previous page and the
instructions below.
1) Rout a channel at the bottom of the overlay panel to the proper dimensions. See "(C)
Routed Area" in the specification diagram and Fig. 8.
2) Drill six 1/4" diameter (hardwood may require slightly larger diameter) holes 3/8"
(10 mm) deep in the locations designated. NOTICE! Use care when drilling holes for
mounting hardware. All drilled holes must be straight and drilled to the correct
diameter and depth. See "(A) Threaded Inserts" and "(B) Threaded Inserts" in the
specification diagram and Fig. 9.
Holes
Holes
Routed Channel
Fig. 9
Fig. 8
3) Screw the 6 threaded wood inserts into the 1/4" holes drilled in the previous step. Make
sure that the inserts are threaded straight and that the tops of the inserts are flush to
the overlay panel surface. Otherwise, the overlay panel cannot be properly fastened to
the door.
4) Mount the door handle hardware. Hoshizaki recommends that the door handle hardware
be mounted on the edge opposite of the door hinge side (optional hinge reversal is
covered in step 6. Countersunk screw heads are required to ensure that the hardware
fasteners do not interfere with the overlay panel fitting flush with the door.
5) While maintaining a hold on the door, remove the hinge stop pin from hinge (B). Pull out
the bottom of the door slightly and gently remove the door from hinge (A). See Fig. 10. If
you are leaving the door right-hinged, skip to step 7. If you would like to reverse the door
hinges, proceed to step 6.
Hinge (B)
Hinge (A)
Fig. 10
Hinge Stop Pin
18
Download from Www.Somanuals.com. All Manuals Search And Download.
6) If you would like to reverse the door hinges, do the following:
a) Contact your local distributor to purchase Hoshizaki Kit HS-0229. The kit contains
"hinge (A)-left."
b) Remove the 2 bolts securing the top panel, then lift it off. See Fig. 11.
c) Remove hinge (A)-right and the bracket from the right side of the appliance. Set
aside hinge (A)-right; it is not needed. Remove the top brace from the left side.
Fasten hinge (A)-left and the bracket to the left side and the top brace to the right
side. See Fig. 12.
Note: When on the proper side, the gasket notch for hinge (A) is to the inside.
Screw
Bolts
Bracket
Top Panel
Hinge (A)-Left
Screw
Top Brace
Gasket Notch
Hinge (A)-Right
Not Needed
Fig. 11
Fig. 12
d) Remove hinge (B) from the right side of the appliance and the 2 filler screws from
the left side. Attach the 2 filler screws to the right side and attach hinge (B) to the
left side. See Fig. 13.
e) Rotate the top panel 180° from its previous position. This brings the notch that was
previously in the right rear to the left front. See Fig. 14. Hook the rear part of the
panel on the body, then secure the front with the 2 bolts removed in step 6a.
Top Panel
Notch
Screws
Hinge (B)
Filler
Screws
Fig. 13
Fig. 14
f) Remove hinge (C1) from the top right part of the door, flip it and reattach to the
bottom left. Remove hinge (C2) from the bottom right part of the door, flip it and
reattach to the top left. See Fig. 15. Proceed to step 7.
Screws
Hinge (C2)
Fig. 15
Hinge (C1)
Screws
19
Download from Www.Somanuals.com. All Manuals Search And Download.
7) Remove the bushings from hinge (C1) and hinge (C2) (the hinges attached to the door).
See Fig. 16.
8) Remove the gasket from the door. See Fig. 17.
Bushing
Gasket
Hinge
Fig. 17
Fig. 16
9) Temporarily fasten the overlay panel to the door using 2 of the M4×25 pan head screws
provided. NOTICE! Ensure that the back surface of overlay panel is flat before
attaching. See Fig. 18.
10) Mark the centerpoint of the hinge (C1) and hinge (C2) holes that extend over the
overlay panel. See Fig. 19.
11) Remove the overlay panel from the door.
Hinge
Mark the center point.
Screws
Door
Overlay Panel
Fig. 18
Fig. 19
12) Drill 3/8" diameter holes 1/4" (7 mm) deep where you marked on the overlay panel to
accommodate the hinge (C1) and hinge (C2) bushings.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) Attachment of Overlay Panel to Door
1) Fasten the sheet metal bracket to the overlay panel using the two M4×8 truss head
screws provided. Snug the screws, but do not tighten. See Fig. 20.
2) Temporarily fasten the overlay panel to the door using 2 of the M4×25 pan head screws
provided. See Fig. 21.
Overlay Panel
Screws
Snug the screws,
but do not tighten.
Sheet Metal Bracket
Fig. 20
Fig. 21
3) Adjust the sheet metal bracket so that it is flush with the bottom of the door. See Fig. 22.
4) Remove the overlay panel from the door and tighten the two M4×8 truss head screws
securing the sheet metal bracket to the overlay panel. See Fig. 23.
Overlay Panel
Tighten the screws.
Door
Sheet Metal Bracket
Sheet Metal Bracket
Fig. 22
Fig. 23
5) Fasten the overlay panel to the door using the four M4×25 pan head screws provided.
Snug the screws, but do not tighten. See Fig. 24.
6) Fasten the sheet metal bracket to the bottom of the door with the three T2 screws
provided. Tighten the screws to the door. See Fig. 25.
Door
Screws
Snug the screws,
but do not tighten.
Overlay Panel
Sheet Metal Bracket
Fig. 24
Fig. 25
21
Download from Www.Somanuals.com. All Manuals Search And Download.
7) Tighten the four M4×25 pan head screws installed in step 5. See Fig. 26.
8) Replace the door gasket in its proper orientation. Reinsert the bushings into hinge (C1)
and hinge (C2) (the hinges attached to the door). See Fig. 27.
Bushing
Tighten the screws.
Gasket
Bushing
Fig. 26
Fig. 27
9) Attach the door to hinge (A), then continue to maintain a hold on the door. Screw the
hinge stop pin into hinge (B) until it is tight. See Fig. 28.
10) Insert the 2 canoe clips included in the accessory bag into the holes on top of the door.
See Fig. 29.
Hinge (B)
Canoe Clips
Hinge Stop Pin
Fig. 28
Fig. 29
22
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Setup
1) Position the appliance in the selected permanent location.
2) Level the appliance from side-to-side and front-to-rear by adjusting the feet.
E. Electrical Connection
WARNING
• Electrical connection must meet national, state, and local electrical code
requirements. Failure to meet these code requirements could result in death,
electric shock, serious injury, fire, or damage.
• The appliance requires an independent power supply of proper capacity. See
the nameplate for electrical specifications. Failure to use an independent power
supply of proper capacity can result in a tripped breaker, blown fuse, damage to
existing wiring, or component failure. This could lead to heat generation or fire.
• THE APPLIANCE MUST BE GROUNDED: The appliance is equipped with a
NEMA 5-15 three-prong grounding plug
to reduce the risk of potential shock
hazards. It must be plugged into a properly grounded, independent 3-prong wall
outlet. If the outlet is a 2-prong outlet, it is your personal responsibility to have
a qualified electrician replace it with a properly grounded, independent 3-prong
wall outlet. Do not remove the ground prong from the power cord and do not use
an adapter plug. Failure to properly ground the appliance could result in death or
serious injury.
• Do not use an extension cord.
• To reduce the risk of electric shock, do not touch the control switch or plug
with damp hands. Make sure the control switch is in the "OFF" position before
plugging in or unplugging the appliance.
• Do not use an appliance with a damaged power cord. The power cord should not
be altered, jerked, bundled, weighed down, pinched, or tangled. Such actions
could result in electric shock or fire. To unplug the appliance, be sure to pull the
plug, not the cord, and do not jerk the cord.
• The GREEN ground wire in the factory-installed power cord is connected to the
appliance. If it becomes necessary to remove or replace the power cord, be sure
to connect the power cord's ground wire to this screw upon reattachment.
• Usually an electrical permit and services of a licensed electrician are required.
• The maximum allowable voltage variation is ±10 percent of the nameplate rating.
• For optional drain pump (HS-5061) installation, refer to the instructions included with
the pump.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
F. Water Supply and Drain Connections
WARNING
Water supply and drain connections must be installed in accordance with applicable
national, state, and local regulations.
NOTICE
• Normal operating water temperature must be within 45°F to 90°F (7°C to
32°C). Operation of the appliance, for extended periods, outside of this normal
temperature range may affect appliance performance.
• Water supply pressure must be a minimum of 7 PSIG and a maximum of
113 PSIG. If the pressure exceeds 113 PSIG, the use of a pressure reducing valve
is required.
• External filters, strainers, or softeners may be required depending on water quality.
Contact your local Hoshizaki Certified Service Representative or local Hoshizaki
distributor for recommendations.
• Connect to potable water supply only. Do not connect to a hot-water supply.
• In areas where water damage is a concern, install in a contained area with a floor
drain.
• Water line installation to the appliance is not warranted by Hoshizaki.
• Water-hammer issues must be resolved by a qualified plumber before installing
the appliance. Water hammer can cause appliance damage that may lead to
water leakage or flooding.
• A minimum of 1/2" nominal ID hard pipe or equivalent is required for the drain
line. Installing a smaller diameter drain line will reduce water flow and may lead to
water leakage or flooding.
• If using the optional drain pump (HS-5061), test its operation every time the
appliance is cleaned and sanitized. See "IV.E. Optional Drain Pump HS-5061" for
details. If the optional drain pump is not operating properly, water could back up
and overflow, leading to costly water damage.
Water Supply
Inlet
Minimum Water Supply Drain Outlet
Line Size
Minimum Drain
Line Size
1/2" Female Pipe 1/4" Nominal ID
Thread (FPT)
1/2" Female Pipe 1/2" Nominal
Copper Water Tubing or Thread (FPT)
ID Hard Pipe or
Equivalent
Equivalent
• A plumbing permit and services of a licensed plumber may be required in some areas.
• A water supply line shut-off valve and drain valve must be installed.
• Be sure there is sufficient extra water supply line and drain line for the appliance to be
pulled out for service.
• Drain line should not be piped directly to the sewer system. An air gap of a minimum of
2 vertical inches (5 cm) must be between the end of the drain pipe from the appliance
and the floor drain.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
• For gravity drain installation, drain must have 1/4" fall per foot (2 cm per 1 m) on horizontal
runs to get good flow. A vented tee connection is also required for proper flow. Extend the
vent at least 12" (30 cm) above the drain outlet.
• For optional drain pump installation, refer to the instructions included with the pump.
Minimum 1/4" Nominal ID Copper Water Tubing or Equivalent
Water Supply Inlet
Be sure there is sufficient extra
1/2" FPT
water supply line and drain line
for the appliance to be pulled
out for service.
Shut-Off Valve
Piping to approved drain.
Leave a 2-inch (5-cm) vertical
air gap between the end of the
pipe and the drain.
Drain Valve
Drain Outlet
1/2" FPT
2-inch (5-cm)
air gap
Vented Tee Connection
Extend the vent at least 12"
(30 cm) above the drain outlet.
Floor
Drain
Minimum 1/2" Nominal ID Hard Pipe
or Equivalent
Fig. 30
25
Download from Www.Somanuals.com. All Manuals Search And Download.
G. Final Checklist
WARNING
CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are
securely in place after installation. Make sure that none have fallen into the storage
bin.
1) Is the appliance level?
2) Is the appliance in a site where the ambient temperature is within 45°F to 100°F (7°C to
38°C) and the water temperature within 45°F to 90°F (7°C to 32°C) all year around?
3) Have the shipping carton, tape, and packing material been removed from the
appliance? Has the protective plastic film been removed from the panels?
4) Have all electrical and water connections been made? Do electrical and water
connections meet all national, state, and local code and regulation requirements?
5) Has the power supply voltage been checked or tested against the nameplate rating? Is
the power supply a properly grounded, independent 3-prong wall outlet?
6) Are the water supply and drain lines sized as specified? Are the water supply line
shut-off valve and drain valve installed? Has the water supply pressure been checked to
ensure a minimum of 7 PSIG and a maximum of 113 PSIG?
7) Are all components, fasteners, and thumbscrews securely in place?
8) Has the end user been given this instruction manual, and instructed on how to operate
the appliance and the importance of the recommended periodic maintenance?
9) Has the end user been given the name and telephone number of an authorized service
agent?
10) Has the warranty tag been filled out and forwarded to the factory for warranty
registration?
26
Download from Www.Somanuals.com. All Manuals Search And Download.
III. Operating Instructions
A. Important Notes About Usage
WARNING
• Only qualified service technicians should install and service the appliance.
• Failure to install, operate, and maintain the equipment in accordance with this
manual will adversely affect safety, performance, component life, and warranty
coverage.
• To reduce the risk of electric shock, do not touch the control switch or plug
with damp hands. Make sure the control switch is in the "OFF" position before
plugging in or unplugging the appliance.
• The appliance must be maintained in accordance with the instruction manual and
labels provided with the appliance. Consult with your local Hoshizaki Certified
Service Representative about maintenance service.
• The appliance must be cleaned and sanitized at least twice a year. More frequent
cleaning and sanitizing may be required in some water conditions.
• Wash your hands before removing ice. Use the plastic scoop provided.
• Do not place fingers or any other objects into the ice discharge opening.
• The appliance is not intended for use by persons (including children) with reduced
physical, sensory, or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
• Young children should be properly supervised around the appliance.
• Do not climb, stand, or hang on the appliance or appliance door or allow children
or animals to do so. Serious injury could occur or the appliance could be
damaged.
• Be careful not to pinch fingers when opening and closing the door. Be careful
when opening and closing the door when children are in the area.
• Do not use combustible spray or place volatile or flammable substances near the
appliance. They might catch fire.
• Keep the area around the appliance clean. Dirt, dust, or insects in the appliance
could cause harm to individuals or damage to the appliance.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE
• Protect the floor when moving the appliance to prevent damage to the floor.
• If using the optional drain pump (HS-5061), test its operation every time the
appliance is cleaned and sanitized. See "IV.E. Optional Drain Pump HS-5061" for
details. If the optional drain pump is not operating properly, water could back up
and overflow, leading to costly water damage.
• To help ensure the storage bin drain remains clear, follow the instructions in
"IV.C. Storage Bin Drain" once every 3 months or as often as necessary for
conditions. If the storage bin drain becomes clogged, water could build up in the
bin and overflow, leading to costly water damage.
• If water collects in the bin and will not drain, turn off the appliance and close the
water supply line shut-off valve. Call for service.
• If water seeps from the base of the appliance, turn off the appliance and close
the water supply line shut-off valve. Call for service. Failure to do so could lead to
costly water damage.
• Do not leave the appliance on during extended periods of non-use, extended
absences, or in sub-freezing temperatures. To properly prepare the appliance for
these occasions, follow the instructions in "V. Preparing the Appliance for Periods
of Non-Use."
• Keep ventilation openings, in the appliance enclosure or in the built-in structure,
clear of obstruction.
• Do not place objects on top of the appliance.
• The storage bin is for ice use only. Do not store anything else in the storage bin.
If ice is not used on a regular basis, it may bond together in the storage bin. In this case,
discard the bonded ice and allow the appliance to make fresh ice.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Startup
WARNING
All parts are factory-adjusted. Improper adjustments may adversely affect safety,
performance, component life, and warranty coverage.
NOTICE
• If the appliance is turned off, wait for at least 3 minutes before restarting the
appliance to prevent damage to the compressor.
• At startup, confirm that all internal and external connections are free of leaks.
1) Open the water supply line shut-off valve.
2) Make sure the control switch is in the "OFF" position. Plug the appliance into the
electrical outlet. WARNING! To reduce the risk of electric shock, do not touch the
control switch or plug with damp hands. If you have to slide the appliance back
for a built-in installation, make sure you do not damage or pinch the water supply
line, drain line, or power cord.
3) If required by sanitation code in your area, seal the perimeter where the appliance
touches the floor with approved caulk compound in a smooth and easily cleanable
manner.
4) Move the control switch to the "ICE" position to start the automatic icemaking process.
5) Once the appliance starts to produce ice, allow it to run for another 30 minutes.
6) Move the control switch to the "OFF" position.
7) Remove the ice produced, then clean the storage bin liner, door liner, and door gasket
using a neutral cleaner. Rinse thoroughly after cleaning.
8) Move the control switch to the "ICE" position to start the automatic icemaking process.
9) To confirm bin control operation, hold ice in contact with the bin control thermostat bulb.
If the icemaker does not stop within 10 seconds, the bin control thermostat must be
adjusted. Installations at higher altitude locations are more likely to require adjustment.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
IV. Maintenance
The appliance must be maintained in accordance with the instruction manual and
labels provided with the appliance. Consult with your local Hoshizaki Certified Service
Representative about maintenance service. To obtain the name and phone number of
WARNING
• Only qualified service technicians should service the appliance.
• Failure to install, operate, and maintain the equipment in accordance with this
manual will adversely affect safety, performance, component life, and warranty
coverage.
• To reduce the risk of electric shock, do not touch the control switch or plug
with damp hands. Make sure the control switch is in the "OFF" position before
plugging in or unplugging the appliance.
• Move the control switch to the "OFF" position and unplug the appliance from the
electrical outlet before servicing.
• CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are
securely in place after any maintenance is done to the appliance. Make sure that
none have fallen into the storage bin.
• Do not place fingers or any other objects into the ice discharge opening.
• After service, make sure that there are no wires pinched between the panels and
appliance. Make sure you do not damage or pinch the water supply line, drain
line, or power cord.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
A. Maintenance Schedule
The maintenance schedule below is a guideline. More frequent maintenance may be
required depending on water quality, the appliance's environment, and local sanitation
regulations.
Maintenance Schedule
Frequency Area
Task
Weekly
Monthly
Scoop
Clean the scoop using a neutral cleaner. Rinse thoroughly after cleaning.
Drain the Appliance Move the control switch to the "DRAIN" position. Allow the water system to
drain for 1 minute. Clear ice away from the thermostatic bin control bulb.
Move the control switch to the "ICE" position. After the gear motor starts,
move the control switch to the "DRAIN" position. Allow the water system to
drain for 1 minute. Move the control switch to the "ICE" position to start the
automatic icemaking process.
Appliance Exterior Wipe down with clean, soft cloth. Use a damp cloth containing a neutral
cleaner to wipe off oil or dirt build up. Clean any chlorine staining (rust
colored spots) using a non-abrasive cleanser.
Every 3
Months
Storage Bin Drain Maintain as outlined in "IV.C. Storage Bin Drain."
Every 6
Months
Icemaker and
Storage Bin
Clean and sanitize per the cleaning and sanitizing instructions provided in
this manual. See "IV.B. Cleaning and Sanitizing Instructions."
Evaporator
Wipe down with clean cloth and warm water.
Condensate Drain
Pan and Gear
Motor Drain Pan
Evaporator
Condensate
Drain Pan
Gear Motor
Drain Pan
Optional Drain
Pump (HS-5061)
External Water
Filters
Test as outlined in "IV.E. Optional Drain Pump HS-5061."
Check for proper pressure and change if necessary.
Yearly
Water Supply Inlet Close the water supply line shut-off valve and drain the water system. Clean
the water supply inlet screen.
Condenser
Water Hoses
Inspect. Clean if necessary. See "IV.D. Condenser."
Inspect the water hoses and clean/replace if necessary.
Upper Bearing
(extruding head)
Check for wear using .02" round stock or pin gauge. Replace both upper
bearing and lower bearing if wear exceeds factory recommendations. See
the Service Manual for details.
After
3 Years,
then Yearly Lower Bearing
and O-Ring
Upper Bearing
(extruding head);
Inspect. Replace both upper bearing and lower bearing if wear exceeds
factory recommendations. Replace the mechanical seal if the seal's contact
surfaces are worn, cracked, or scratched.
(lower housing);
Mechanical
Seal; Evaporator
Cylinder; Auger
31
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Cleaning and Sanitizing Instructions
The appliance must be cleaned and sanitized at least twice a year. More frequent
cleaning and sanitizing may be required in some conditions.
WARNING
• To prevent injury to individuals and damage to the appliance, do not use ammonia
type cleaners.
• Carefully follow any instructions provided with the cleaning and sanitizing
solutions.
• Always wear liquid-proof gloves and goggles to prevent the cleaning and sanitizing
solutions from coming into contact with skin or eyes.
• Do not use ice made from the cleaning and sanitizing solutions. After cleaning and
sanitizing, be careful not to leave any solution in the appliance.
• Do not place fingers or any other objects into the ice discharge opening (extruding
head).
1. Cleaning Solution
Dilute 1.6 fl. oz. (47 ml or 3.2 tbs) of Hoshizaki "Scale Away" or Nu-Calgon "Liquid Ice
Machine Cleaner" with 1 qt (1 l) of warm water. This is a minimum amount. Make more
solution if necessary. IMPORTANT! For safety and maximum effectiveness, use the
solution immediately after dilution.
2. Cleaning Procedure
1) Move the control switch to the "OFF" position.
2) Remove all ice from the storage bin.
3) Move the control switch to the "DRAIN" position.
4) Allow the water system to drain for 1 minute.
5) Move the control switch to the "OFF" position.
6) Using a clean funnel and hose (not included), pour 1 qt (1 l) of cleaning solution
over the extruding head. See Fig. 31. Allow the appliance to sit for 10 minutes before
operation.
Funnel and Hose
(not included)
Extruding Head
Scoop Holder
Slope
Fig. 31
32
Download from Www.Somanuals.com. All Manuals Search And Download.
7) Make sure at least 10 minutes have elapsed since you poured the cleaning solution
over the extruding head, then move the control switch to the "ICE" position.
8) Allow the appliance to make ice for 20 minutes, then move the control switch to the
"DRAIN" position.
9) Allow the water system to drain for 1 minute.
10) Move the control switch to the "ICE" position.
11) After the gear motor starts, move the control switch to the "DRAIN" position.
12) Allow the water system to drain for 1 minute.
13) Move the control switch to the "OFF" position. In severe water conditions, repeat the
cleaning procedure.
Note: If you do not sanitize the appliance, go to step 8 in "IV.B.5. Sanitizing
Procedure - Final."
3. Sanitizing Solution
Dilute 1.25 fl. oz. (37 ml or 2.5 tbs) of a 5.25% sodium hypochlorite solution (chlorine
bleach) with 2.5 gallons (9.5 l) of warm water. This is a minimum amount. Make more
solution if necessary. Using a chlorine test strip or other method, confirm that you have a
concentration of about 200 ppm. IMPORTANT! For safety and maximum effectiveness,
use the solution immediately after dilution.
4. Sanitizing Procedure - Initial
1) Using a clean funnel and hose, pour 1 qt (1 l) of sanitizing solution over the extruding
head. Allow the appliance to sit for 10 minutes before operation.
2) Remove the slope from the storage bin by carefully bending it in the center and
releasing it from the 2 slope shafts.
3) Remove the scoop. Remove the 2 thumbscrews securing the scoop holder, then remove
it.
4) Pour some of the sanitizing solution into a separate, clean container. Using this
sanitizing solution and a clean cloth, wipe down the slope, scoop, scoop holder, inside
of the spout, and bin liner.
5) Rinse the parts and areas sanitized in step 4 thoroughly with clean water.
6) Replace all removed parts in their original and correct positions. WARNING! CHOKING
HAZARD: Ensure all components, fasteners, and thumbscrews are securely in
place. Make sure that none have fallen into the storage bin.
7) Make sure at least 10 minutes have elapsed since you poured the sanitizing solution
over the extruding head, then move the control switch to the "ICE" position.
8) Allow the appliance to make ice for 20 minutes, then move the control switch to the
"DRAIN" position.
9) Allow the water system to drain for 1 minute.
10) Move the control switch to the "ICE" position.
11) After the gear motor starts, move the control switch to the "DRAIN" position.
12) Allow the water system to drain for 1 minute.
13) Move the control switch to the "OFF" position.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Sanitizing Procedure - Final
1) Using a clean funnel and hose, pour 1 qt (1 l) of sanitizing solution over the extruding
head. Allow the appliance to sit for 10 minutes before operation.
2) Move the control switch to the "ICE" position.
3) Allow the appliance to make ice for 20 minutes, then move the control switch to the
"DRAIN" position.
4) Allow the water system to drain for 1 minute.
5) Move the control switch to the "ICE" position.
6) After the gear motor starts, move the control switch to the "DRAIN" position.
7) Allow the water system to drain for 1 minute.
8) Move the control switch to the "ICE" position and allow the appliance to run. Check for
leaks.
9) After 30 minutes, move the control switch to the "OFF" position.
10) Pour warm water into the storage bin to melt all of the ice, then clean the storage bin
liner, door liner, and door gasket with a neutral cleaner. Rinse thoroughly after cleaning.
11) Move the control switch to the "ICE" position to start the automatic icemaking process.
C. Storage Bin Drain
In some conditions, slime may build up inside the storage bin drain and prevent water
from draining properly. To prevent this buildup, perform the following procedure once
every 3 months or as often as necessary for conditions.
NOTICE
If the storage bin drain becomes clogged, water could build up in the bin and
overflow, leading to costly water damage.
1) Move the control switch to the "OFF" position. WARNING! To reduce the risk of
electric shock, do not touch the control switch with damp hands.
2) Remove all ice from the storage bin.
3) Mix a batch of sanitizing solution by diluting 1.25 fl. oz. (37 ml or 2.5 tbs) of a
5.25% sodium hypochlorite solution (chlorine bleach) with 2.5 gallons (9.5 l) of warm
water. Using a chlorine test strip or other method, confirm that you have a concentration
of about 200 ppm. IMPORTANT! For safety and maximum effectiveness, use the
solution immediately after dilution.
4) Slowly pour the sanitizing solution into the storage bin.
5) After all of the solution has drained, clean the storage bin liner with a neutral cleaner.
Rinse thoroughly with clean water.
6) Move the control switch to the "ICE" position to start the automatic icemaking process.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Condenser
Check the condenser once a year, and clean if required by following the steps below.
More frequent cleaning may be required depending on location.
WARNING
Condenser fins are sharp. Use care when cleaning.
1) Move the control switch to the "OFF" position, then unplug the appliance from the
electrical outlet. WARNING! To reduce the risk of electric shock, do not touch the
control switch or plug with damp hands.
2) Remove the screws securing the front panel, then remove it. See Fig. 32.
3) Remove the screws securing the louver, then remove it.
4) Use a brush attachment on a vacuum cleaner to gently clean the condenser fins. Do not
use too much force, otherwise the fins could be damaged.
5) Replace the louver and front panel in their correct positions. Ensure that the screws are
securely in place.
6) Plug the appliance back in. Move the control switch to the "ICE" position to start the
automatic icemaking process.
Front Panel
Condenser
Screws
Fig. 32
Screws
Louver
35
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Optional Drain Pump HS-5061
If the optional drain pump (HS-5061) is installed, test its operation at least twice a year
as outlined below. Note that the pump has power even when the control switch is in the
"OFF" position.
NOTICE
If the optional drain pump is not operating properly, it will adversely affect
performance, component life, and warranty coverage and may result in costly water
damage.
1) Move the control switch to the "OFF" position, then unplug the appliance from the
electrical outlet. WARNING! To reduce the risk of electric shock, do not touch the
control switch or plug with damp hands.
2) Remove all ice from the storage bin.
3) Plug the appliance back in.
4) Slowly pour 24 to 30 oz. (710 to 890 ml) of water over the storage bin drain hole in the
storage bin.
5) If water pumps out properly and the drain pump then de-energizes, proceed to step 6.
If water does not pump out properly and/or the drain pump does not de-energize, the
appliance must be serviced by a qualified service technician before proceeding.
6) Move the control switch to the "ICE" position.
7) Pour another 24 to 30 oz. (710 to 890 ml) of water into the appliance's ice storage bin,
then completely restrict the discharge hose while the drain pump is operating. See
Fig. 33. Pour more water into the appliance's ice storage bin until the appliance turns
off. The drain pump will continue to operate. Check for leaks.
8) Remove the discharge hose restriction and allow the water to be pumped out normally.
Power to the appliance will be restored when the water in the drain pump returns to a
normal level.
9) If the appliance fails to turn off with the discharge hose restricted or the pump fails to
pump out the water, the appliance must be serviced by a qualified service technician.
Fig. 33
Discharge Hose
36
Download from Www.Somanuals.com. All Manuals Search And Download.
V. Preparing the Appliance for Periods of Non-Use
During extended periods of non-use, extended absences, or in sub-freezing
temperatures, follow the instructions below. When the appliance is not used for two or
three days under normal conditions, it is sufficient to move the control switch to the "OFF"
position.
WARNING
Only qualified service technicians should service the appliance.
NOTICE
During extended periods of non-use, extended absences, or in sub-freezing
temperatures, follow the instructions below to reduce the risk of costly water
damage.
1) Move the control switch to the "OFF" position. WARNING! To reduce the risk of
electric shock, do not touch the control switch or plug with damp hands.
2) Close the water supply line shut-off valve, then open the water supply line drain valve.
3) Allow the line to drain by gravity.
4) Move the control switch to the "DRAIN" position.
5) Allow the water system to drain for 1 minute.
6) Attach a compressed air or carbon dioxide supply to the water supply line drain valve.
7) Move the control switch to the "ICE" position.
8) Blow the water supply line out using the compressed air or carbon dioxide supply.
9) Close the water supply line drain valve.
10) Move the control switch to the "OFF" position, then unplug the appliance from the
electrical outlet.
11) Remove the screws securing the upper rear panel, then remove it. See Fig. 34.
12) Remove the clamp securing the reservoir outlet hose to the reservoir. Disconnect the
reservoir outlet hose from the reservoir.
13) Attach a compressed air or carbon dioxide supply to the reservoir outlet hose.
Upper Rear Panel
Reservoir
Fig. 34
Clamp
Reservoir
Outlet
Hose
Overflow Hose
37
Download from Www.Somanuals.com. All Manuals Search And Download.
14) Plug the appliance back in, then move the control switch to the "DRAIN" position.
15) Blow out the reservoir outlet hose using the compressed air or carbon dioxide supply.
16) Move the control switch to the "OFF" position, then unplug the appliance from the
electrical outlet.
17) Reconnect the reservoir outlet hose to the reservoir, then secure with the clamp. Make
sure all hoses are connected and secure.
18) Replace the rear panel in its correct position.
19) Clean the storage bin by using a neutral cleaner. Rinse thoroughly after cleaning.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
VI. Disposal
The appliance contains refrigerant and must be disposed of in accordance with
applicable national, state, and local codes and regulations. Refrigerant must be
recovered by properly certified service personnel.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
HOSHIZAKI AMERICA, INC.
618 Hwy. 74 S., Peachtree City, GA 30269 USA TEL (770) 487-2331 FAX (770) 487-3360 www.hoshizaki.com 1A3094-010
Download from Www.Somanuals.com. All Manuals Search And Download.
|