Honeywell Marine Radio 5610 5613 User Manual
N56XX Decoded Engine  
For 5610/5613, 5680/5683, 5690/5693 Engines  
User’s Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Product Agency Compliance  
Note: It is the OEM manufacturer’s responsibility to comply with applicable regulation(s) in regard to standards for specific  
equipment combinations.  
USA and Canada  
UL Statement (Recognized component)  
UL listed: UL60950-1, 2nd Edition.  
C-UL listed: CSA C22.2 No.60950-1-07, 2nd Edition for I.T.E. product safety.  
Europe  
Honeywell shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is  
not CE marked and does not comply with the Low Voltage Directive.  
For CE-related inquiries, contact:  
Hand Held Products Europe B.V.  
Nijverheidsweg 9-13  
5627 BT Eindhoven  
The Netherlands  
D-Mark Statement  
Certified to EN 60950-1 Information Technology Equipment product safety.  
International  
LED Safety Statement  
LEDs have been tested and classified as “EXEMPT RISK GROUP” to the standard: IEC 62471:2006.  
CB Scheme  
Certified to CB Scheme IEC 60950-1, Second Edition.  
Laser Safety Statement  
Note: Applies only to N56X3 models.  
This device has been tested in accordance with and complies with IEC60825-1 ed2 (2007)  
The Standard also states that the following be included in all user documentation, spec sheets, and brochures, which  
describe this product:  
"Caution - Use of controls or adjustments or performance of procedures other than those specified herein may  
result in hazardous radiation exposure."  
Note: This warning states that altering the inner parts of the laser engine in a way not specified in the user guide may cause  
light levels to exceed Class 2 limits. It is not an issue when using under normal conditions.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Required Safety Labels  
ESD Precautions  
The engine is shipped in ESD safe packaging. Use care when handling the scan engine outside its packaging. Be sure ground-  
ing wrist straps and properly grounded work areas are used.  
Dust and Dirt  
The engine must be sufficiently enclosed to prevent dust particles from gathering on the engine and lens. When stocking the  
unit, keep it in its protective packaging. Dust and other external contaminants will eventually degrade unit performance.  
Honeywell Scanning & Mobility Product Environmental Information  
Refer to www.honeywellaidc.com/environmental for the RoHS / REACH / WEEE information.  
Patents  
For patent information, please refer to www.honeywellaidc.com/patents.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Chapter 1 - Getting Started  
Introduction ..........................................................................................................................1-1  
About This Manual...............................................................................................................1-1  
Unpacking Your Device .......................................................................................................1-1  
OEM Engine Models............................................................................................................1-1  
Connecting the Development Engine to the PC ..................................................................1-2  
Connecting with USB .....................................................................................................1-2  
Connecting with RS232 Serial Port................................................................................1-3  
Menu Bar Code Security Settings........................................................................................1-4  
Setting Custom Defaults ......................................................................................................1-4  
Resetting the Custom Defaults ............................................................................................1-5  
Chapter 2 - Programming the Interface  
Introduction ..........................................................................................................................2-1  
Programming the Interface - Plug and Play .........................................................................2-1  
Keyboard Wedge ...........................................................................................................2-1  
Laptop Direct Connect ...................................................................................................2-1  
RS232 Serial Port ..........................................................................................................2-1  
USB IBM SurePos..........................................................................................................2-2  
USB PC or Macintosh Keyboard....................................................................................2-2  
USB HID.........................................................................................................................2-2  
USB Serial......................................................................................................................2-3  
®
Verifone Ruby Terminal Default Settings.....................................................................2-3  
®
Gilbarco Terminal Default Settings ..............................................................................2-4  
Honeywell Bioptic Aux Port Configuration......................................................................2-4  
®
Datalogic™ Magellan Aux Port Configuration..............................................................2-4  
NCR Bioptic Aux Port Configuration ..............................................................................2-4  
Wincor Nixdorf Terminal Default Settings ......................................................................2-5  
Wincor Nixdorf Beetle™ Terminal Default Settings .......................................................2-5  
Keyboard Country Layout ....................................................................................................2-5  
Keyboard Style...................................................................................................................2-13  
Keyboard Conversion ........................................................................................................2-14  
Control Character Output...................................................................................................2-14  
Keyboard Modifiers ............................................................................................................2-15  
RS232 Modifiers ................................................................................................................2-16  
RS232 Baud Rate ........................................................................................................2-16  
RS232 Word Length: Data Bits, Stop Bits, and Parity .................................................2-17  
RS232 Receiver Time-Out...........................................................................................2-18  
RS232 Handshaking ....................................................................................................2-18  
RS232 Timeout ............................................................................................................2-19  
XON/XOFF...................................................................................................................2-19  
ACK/NAK .....................................................................................................................2-19  
RS232 Stop Mode........................................................................................................2-20  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
Scanner to Bioptic Communication ...................................................................................2-20  
Scanner-Bioptic Packet Mode .....................................................................................2-20  
Scanner-Bioptic ACK/NAK Mode.................................................................................2-20  
Scanner-Bioptic ACK/NAK Timeout.............................................................................2-21  
Chapter 3 - Input/Output Settings  
Power Up Beeper ................................................................................................................3-1  
Beep on BEL Character....................................................................................................... 3-1  
Trigger Click ........................................................................................................................3-1  
Good Read and Error Indicators..........................................................................................3-2  
Beeper – Good Read.....................................................................................................3-2  
Beeper Volume – Good Read........................................................................................3-2  
Beeper Pitch – Good Read............................................................................................3-2  
Beeper Pitch – Error ...................................................................................................... 3-3  
Beeper Duration – Good Read ......................................................................................3-3  
LED – Good Read .........................................................................................................3-3  
Number of Beeps – Good Read ....................................................................................3-4  
Number of Beeps – Error............................................................................................... 3-4  
Good Read Delay ..........................................................................................................3-4  
User-Specified Good Read Delay..................................................................................3-4  
Manual Trigger Modes.........................................................................................................3-5  
Serial Trigger Mode.............................................................................................................3-5  
Read Time-Out ..............................................................................................................3-5  
Presentation Mode .............................................................................................................. 3-5  
LED Illumination - Presentation Mode ........................................................................... 3-6  
Presentation LED Behavior after Decode......................................................................3-6  
Presentation Sensitivity ................................................................................................. 3-6  
Streaming Presentation™ Mode ......................................................................................... 3-7  
Mobile Phone Read Mode...................................................................................................3-7  
Image Snap and Ship..........................................................................................................3-7  
Hands Free Time-Out.......................................................................................................... 3-8  
Reread Delay.......................................................................................................................3-8  
User-Specified Reread Delay ........................................................................................3-8  
2D Reread Delay ........................................................................................................... 3-9  
Illumination Lights................................................................................................................3-9  
Aimer Delay.......................................................................................................................3-10  
User-Specified Aimer Delay......................................................................................... 3-10  
Aimer Mode .......................................................................................................................3-10  
Centering........................................................................................................................... 3-10  
Preferred Symbology......................................................................................................... 3-12  
High Priority Symbology .............................................................................................. 3-12  
Low Priority Symbology ............................................................................................... 3-12  
Preferred Symbology Time-out.................................................................................... 3-13  
Preferred Symbology Default....................................................................................... 3-13  
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Output Sequence Overview...............................................................................................3-13  
Output Sequence Editor ..............................................................................................3-13  
To Add an Output Sequence .......................................................................................3-13  
Other Programming Selections.................................................................................... 3-13  
Output Sequence Editor ..............................................................................................3-15  
Partial Sequence .........................................................................................................3-15  
Require Output Sequence ...........................................................................................3-15  
Multiple Symbols ............................................................................................................... 3-16  
No Read ............................................................................................................................3-16  
Video Reverse...................................................................................................................3-16  
Working Orientation........................................................................................................... 3-17  
Chapter 4 - Data Editing  
Prefix/Suffix Overview ......................................................................................................... 4-1  
To Add a Prefix or Suffix:............................................................................................... 4-1  
To Clear One or All Prefixes or Suffixes........................................................................ 4-2  
To Add a Carriage Return Suffix to All Symbologies..................................................... 4-2  
Prefix Selections..................................................................................................................4-2  
Suffix Selections..................................................................................................................4-3  
Function Code Transmit ......................................................................................................4-3  
Intercharacter, Interfunction, and Intermessage Delays......................................................4-3  
Intercharacter Delay ...................................................................................................... 4-3  
User Specified Intercharacter Delay.............................................................................. 4-4  
Interfunction Delay......................................................................................................... 4-4  
Intermessage Delay....................................................................................................... 4-5  
Chapter 5 - Data Formatting  
Data Format Editor Introduction ..........................................................................................5-1  
Add a Data Format ..............................................................................................................5-1  
Other Programming Selections...................................................................................... 5-2  
Terminal ID Table................................................................................................................5-3  
Data Format Editor Commands...........................................................................................5-3  
Move Commands........................................................................................................... 5-6  
Search Commands........................................................................................................ 5-7  
Miscellaneous Commands.............................................................................................5-9  
Data Formatter ..................................................................................................................5-12  
Data Format Non-Match Error Tone............................................................................ 5-13  
Primary/Alternate Data Formats........................................................................................5-13  
Single Scan Data Format Change...............................................................................5-13  
Chapter 6 - Symbologies  
All Symbologies................................................................................................................... 6-1  
Message Length Description...............................................................................................6-1  
Codabar............................................................................................................................... 6-2  
Codabar Concatenation.................................................................................................6-3  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Code 39............................................................................................................................... 6-4  
Code 32 Pharmaceutical (PARAF)................................................................................6-5  
Full ASCII.......................................................................................................................6-6  
Code 39 Code Page ......................................................................................................6-6  
Interleaved 2 of 5.................................................................................................................6-7  
NEC 2 of 5...........................................................................................................................6-8  
Code 93............................................................................................................................... 6-9  
Code 93 Code Page ....................................................................................................6-10  
Straight 2 of 5 Industrial (three-bar start/stop)................................................................... 6-11  
Straight 2 of 5 IATA (two-bar start/stop)............................................................................ 6-12  
Matrix 2 of 5.......................................................................................................................6-13  
Code 11............................................................................................................................. 6-14  
Code 128...........................................................................................................................6-15  
ISBT 128 Concatenation..............................................................................................6-15  
Code 128 Code Page ..................................................................................................6-16  
GS1-128 ............................................................................................................................6-17  
Telepen.............................................................................................................................. 6-18  
UPC-A ............................................................................................................................... 6-19  
UPC-A/EAN-13  
with Extended Coupon Code ..........................................................................................6-21  
Coupon GS1 DataBar Output............................................................................................ 6-21  
UPC-E0 .............................................................................................................................6-22  
UPC-E1 .............................................................................................................................6-24  
EAN/JAN-13 ......................................................................................................................6-24  
Convert UPC-A to EAN-13 .......................................................................................... 6-24  
ISBN Translate ............................................................................................................6-26  
EAN/JAN-8 ........................................................................................................................6-27  
MSI ....................................................................................................................................6-29  
GS1 DataBar Omnidirectional ........................................................................................... 6-31  
GS1 DataBar Limited......................................................................................................... 6-31  
GS1 DataBar Expanded....................................................................................................6-32  
Trioptic Code ..................................................................................................................... 6-32  
Codablock A ......................................................................................................................6-33  
Codablock F ......................................................................................................................6-34  
PDF417 .............................................................................................................................6-35  
MacroPDF417 ................................................................................................................... 6-35  
MicroPDF417.....................................................................................................................6-36  
GS1 Composite Codes......................................................................................................6-36  
UPC/EAN Version........................................................................................................ 6-37  
GS1 Emulation .................................................................................................................. 6-37  
TCIF Linked Code 39 (TLC39) ..........................................................................................6-38  
QR Code............................................................................................................................6-38  
QR Code Page ............................................................................................................6-39  
Data Matrix ........................................................................................................................6-40  
Data Matrix Code Page ...............................................................................................6-40  
MaxiCode .......................................................................................................................... 6-41  
Aztec Code........................................................................................................................ 6-42  
Aztec Code Page.........................................................................................................6-42  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chinese Sensible (Han Xin) Code..................................................................................... 6-43  
Postal Codes - 2D ............................................................................................................. 6-44  
Single 2D Postal Codes:..............................................................................................6-44  
Combination 2D Postal Codes:....................................................................................6-45  
Postal Codes - Linear........................................................................................................6-48  
China Post (Hong Kong 2 of 5).................................................................................... 6-48  
Korea Post................................................................................................................... 6-49  
Chapter 7 - Imaging Commands  
Single-Use Basis .................................................................................................................7-1  
Command Syntax................................................................................................................7-1  
Image Snap - IMGSNP........................................................................................................7-1  
IMGSNP Modifiers......................................................................................................... 7-1  
Image Ship - IMGSHP.........................................................................................................7-3  
IMGSHP Modifiers......................................................................................................... 7-3  
Intelligent Signature Capture - IMGBOX ...........................................................................7-10  
Signature Capture Optimize ........................................................................................7-10  
IMGBOX Modifiers....................................................................................................... 7-11  
RF Default Imaging Device................................................................................................ 7-14  
Chapter 8 - Interface Keys  
Keyboard Function Relationships........................................................................................8-1  
Supported Interface Keys.................................................................................................... 8-3  
Chapter 9 - Utilities  
To Add a Test Code I.D. Prefix to All Symbologies.............................................................9-1  
Show Decoder Revision ......................................................................................................9-1  
Show Scan Driver Revision................................................................................................. 9-1  
Show Software Revision...................................................................................................... 9-1  
Show Data Format............................................................................................................... 9-1  
Test Menu............................................................................................................................9-2  
TotalFreedom ...................................................................................................................... 9-2  
Application Plug-Ins (Apps) ................................................................................................. 9-2  
EZConfig-Scanning Introduction..........................................................................................9-3  
Installing EZConfig-Scanning from the Web..................................................................9-3  
Resetting the Factory Defaults ............................................................................................ 9-4  
Chapter 10 - Serial Programming Commands  
Conventions.......................................................................................................................10-1  
Menu Command Syntax....................................................................................................10-1  
Query Commands .............................................................................................................10-1  
Responses...................................................................................................................10-2  
Trigger Commands............................................................................................................10-3  
Resetting the Custom Defaults.......................................................................................... 10-3  
Menu Commands ..............................................................................................................10-4  
v
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 11 - Maintenance  
Repairs .............................................................................................................................. 11-1  
Inspecting Cords and Connectors .....................................................................................11-1  
Troubleshooting.................................................................................................................11-1  
Chapter 12 - Customer Support  
Technical Assistance......................................................................................................... 12-1  
Product Service and Repair...............................................................................................12-1  
Appendix A - Reference Charts  
Symbology Charts ...............................................................................................................A-1  
Linear Symbologies .......................................................................................................A-1  
2D Symbologies.............................................................................................................A-3  
Postal Symbologies .......................................................................................................A-3  
ASCII Conversion Chart (Code Page 1252)........................................................................A-3  
Lower ASCII Reference Table.............................................................................................A-4  
ISO 2022/ISO 646 Character Replacements ......................................................................A-8  
Unicode Key Maps ............................................................................................................A-10  
vi  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1
Getting Started  
Introduction  
The N56XX engine is designed for integration into a wide range of OEM devices. The engine’s compact mechanical design can  
drop into many existing applications, allowing OEMs and third-party manufacturers to integrate the benefits of image-based  
scanning into a variety of devices, including hand held computers (PDTs, medical instrumentation, kiosks, diagnostic equip-  
ment, and robotics.  
Three different decoding configurations provide OEMs the flexibility required to address various application-specific needs. The  
N5610/5613, with linear decoding, delivers laser-like reading on linear codes. The N5680/5683 unit decodes linear as well as  
2D and postal codes. In addition to linear, 2D, and postal codes, the N5690/5693 unit includes the OCR feature. The units can  
be purchased either with a bright green LED (56X0) or a high visibility laser (56X3) For software updates and additional infor-  
mation, visit the Honeywell website at www.honeywellaidc.com.  
About This Manual  
This User’s Guide provides demonstration, installation, and programming instructions for the N56XX engine.  
Honeywell’s bar code scan engines are factory programmed for the most common terminal and communications settings. If you  
need to change these settings, programming is accomplished by scanning the bar codes in this guide.  
An asterisk (*) next to an option indicates the default setting.  
Unpacking Your Device  
After you open the shipping carton containing the OEM engine(s), take the following steps:  
•
•
•
Check for damage during shipment. Report damage immediately to the carrier who delivered the carton.  
Make sure the items in the carton match your order.  
Save the shipping container for later storage or shipping.  
OEM Engine Models  
There are three models of the OEM engine, which may be used with the interfaces described in this manual. Refer to the chart  
below to determine the models that can be used with your interface.  
Models  
Interface  
Decoding Capability  
N568XX-XXX-XX2  
N568XX-XXX-XX3  
N568XX-XXX-XX5  
N569XX-XXX-XX2  
N569XX-XXX-XX3  
N569XX-XXX-XX5  
TTL Level 232  
Linear, 2D, postal  
Full-Speed USB  
High-Speed USB  
TTL Level 232  
Linear, 2D, postal  
Linear, 2D, postal  
Linear, 2D, postal, OCR  
Linear, 2D, postal, OCR  
Linear, 2D, postal, OCR  
Full-Speed USB  
High-Speed USB  
Note: The N56XX decoded out engine can be used by customers to evaluate the N5600 non-decoded out engine. Refer to the  
N5600 Integration Manual for detailed part numbers and integration information.  
1 - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Connecting the Development Engine to the PC  
The development OEM engine can connect to a PC for evaluation.  
Connecting with USB  
Note: If using the N56XXX-XXX-XX5 engine with USB Micro-B, do not supply power through the flex connector. Doing so  
may damage the host or engine. The N56XXX-XXX-XX5 engine will only communicate USB through the Micro-B  
connector. The N56XXX-XXX-XX3 engine will only communicate USB through the 10 pin modular connector.  
1. Turn off power to the terminal/computer.  
2. If using full-speed USB, connect the USB interface cable to the interface board and to the matching USB port on the  
computer.  
If using high-speed USB, connect the USB interface cable to side of the engine and to the USB port on the computer.  
Note: For additional USB programming and technical information, refer to Honeywell’s “USB Application Note,” available at  
www.honeywellaidc.com.  
1 - 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
3. When connecting the engine using full-speed or high-speed USB, all communication parameters between the engine  
and terminal must match for correct data transfer using USB protocol. Scan the appropriate USB interface bar code  
below.  
Full-Speed USB  
High-Speed USB  
4. Verify the engine operation by scanning a bar code from the Sample Symbols in the back of this manual. The engine  
beeps once when a bar code is successfully decoded.  
Connecting with RS232 Serial Port  
1. If using an RS-232 connection, connect the serial interface cable to the interface board and to the matching port on the  
back of the computer.  
2. Connect the power supply connector to the serial interface cable. Plug in the power supply.  
3. Turn the terminal/computer power back on. The engine beeps.  
4. If connecting the engine using an RS-232 interface, all communication parameters between the engine and terminal  
must match for correct data transfer through the serial port using RS-232 protocol. Scan the RS-232 interface bar code  
below. This programs the engine for an RS-232 interface at 115,200 baud, parity–none, 8 data bits, 1 stop bit, and adds  
a suffix of a CR LF.  
RS-232 Interface  
5. Verify the engine operation by scanning a bar code from the Sample Symbols in the back of this manual. The engine  
beeps once when a bar code is successfully decoded.  
To connect an engine to your host system, refer to the N56XX Integration Manual.  
1 - 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The engine has a view finder that projects a bright red aiming beam that corresponds to the engine’s horizontal field of view.  
The aiming beam should be centered over the bar code, but it can be positioned in any direction for a good read.  
Linear bar code  
2D Matrix symbol  
The aiming beam is smaller when the engine is closer to the code and larger when it is farther from the code. Symbologies with  
smaller bars or elements (mil size) should be read closer to the unit. Symbologies with larger bars or elements (mil size) should  
be read farther from the unit. To read single or multiple symbols (on a page or on an object), hold the engine at an appropriate  
distance from the target, pull the trigger, and center the aiming beam on the symbol. If the code being scanned is highly reflec-  
tive (e.g., laminated), it may be necessary to tilt the code up 15° to 18° to prevent unwanted reflection.  
Menu Bar Code Security Settings  
Honeywell scan engines are programmed by scanning menu bar codes or by sending serial commands to the scan engine. If  
you want to restrict the ability to scan menu codes, you can use the Menu Bar Code Security settings. Please contact the near-  
est technical support office (see Limited Warranty on page 12-1) for further information.  
Setting Custom Defaults  
You have the ability to create a set of menu commands as your own, custom defaults. To do so, scan the Set Custom Defaults  
bar code below before scanning the menu commands for your custom defaults. If a menu command requires scanning numeric  
codes from the back cover, then a Save code, that entire sequence will be saved to your custom defaults. When you have  
entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults bar code.  
Set Custom Defaults  
Save Custom Defaults  
1 - 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
You may have a series of custom settings and want to correct a single setting. To do so, just scan the new setting to overwrite  
the old one. For example, if you had previously saved the setting for Beeper Volume at Low to your custom defaults, and decide  
you want the beeper volume set to High, just scan the Set Custom Defaults bar code, then scan the Beeper Volume High  
menu code, and then Save Custom Defaults. The rest of the custom defaults will remain, but the beeper volume setting will be  
updated.  
Resetting the Custom Defaults  
If you want the custom default settings restored to your scan engine, scan the Activate Custom Defaults bar code below. This  
is the recommended default bar code for most users. It resets the scan engine to the custom default settings. If there are no  
custom defaults, it will reset the scan engine to the factory default settings. Any settings that have not been specified through  
the custom defaults will be defaulted to the factory default settings.  
Activate Custom Defaults  
1 - 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
1 - 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
Programming the Interface  
Introduction  
This chapter describes how to program your system for the desired interface.  
Programming the Interface - Plug and Play  
Plug and Play bar codes provide instant scanner set up for commonly used interfaces.  
Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.  
Keyboard Wedge  
If you want your system programmed for an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard,  
scan the bar code below. Keyboard wedge is the default interface.  
Note: The following bar code also programs a carriage return (CR) suffix.  
IBM PC AT and Compatibles with  
CR suffix  
Laptop Direct Connect  
For most laptops, scanning the Laptop Direct Connect bar code allows operation of the scan engine in parallel with the  
integral keyboard. The following Laptop Direct Connect bar code also programs a carriage return (CR) suffix and turns on  
Emulate External Keyboard (page 2-14).  
Laptop Direct Connect  
with CR suffix  
RS232 Serial Port  
The RS232 Interface bar code is used when connecting to the serial port of a PC or terminal. The following RS232 Inter-  
face bar code also programs a carriage return (CR) and a line feed (LF) suffix, baud rate, and data format as indicated  
below. It also changes the trigger mode to manual.  
Option  
Setting  
Baud Rate  
115,200 bps  
Data Format  
8 data bits, no parity bit, 1 stop bit  
RS232 Interface  
2 - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
USB IBM SurePos  
Scan one of the following “Plug and Play” codes to program the scan engine for an IBM SurePos (USB handheld scanner)  
or IBM SurePos (USB tabletop scanner) interface.  
Note: After scanning one of these codes, you must power cycle the cash register.  
USB IBM SurePos  
(USB Handheld Scanner)  
Interface  
USB IBM SurePos  
(USB Tabletop Scanner)  
Interface  
Each bar code above also programs the following suffixes for each symbology:  
Symbology  
Suffix  
Symbology  
Suffix  
EAN 8  
EAN 13  
UPC A  
UPC E  
0C  
16  
0D  
0A  
Code 39  
Interleaved 2 of 5  
Code 128  
00 0A 0B  
00 0D 0B  
00 18 0B  
00 0A 0B  
Code 39  
USB PC or Macintosh Keyboard  
Scan one of the following codes to program the scan engine for USB PC Keyboard or USB Macintosh Keyboard. Scanning  
these codes also adds a CR suffix.  
(PC)  
USB Keyboard  
USB Keyboard (Mac)  
USB Japanese Keyboard (PC)  
USB HID  
Scan the following code to program the scan engine for USB HID bar code scanners.  
USB HID Bar Code Scanner  
2 - 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
USB Serial  
Scan the following code to program the scan engine to emulate a regular RS232-based COM Port. If you are using a Mic-  
rosoft® Windows® PC, you will need to download a driver from the Honeywell website (www.honeywellaidc.com). The  
driver will use the next available COM Port number. Apple® Macintosh computers recognize the scan engine as a USB  
CDC class device and automatically use a class driver.  
USB Serial  
Note: No extra configuration (e.g., baud rate) is necessary.  
CTS/RTS Emulation  
CTS/RTS Emulation On  
* CTS/RTS Emulation Off  
ACK/NAK Mode  
ACK/NAK Mode On  
* ACK/NAK Mode Off  
Verifone® Ruby Terminal Default Settings  
Scan the following Plug and Play code to program the scan engine for a Verifone Ruby terminal. This bar code sets the  
baud rate to 1200 bps and the data format to 8 data bits, no parity bit, 1 stop bit. It also adds a line feed (LF) suffix and pro-  
grams the following prefixes for each symbology:  
Symbology  
Prefix  
UPC-A  
UPC-E  
EAN-8  
EAN-13  
A
A
FF  
F
Verifone Ruby Settings  
2 - 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Gilbarco® Terminal Default Settings  
Scan the following Plug and Play code to program the scan engine for a Gilbarco terminal. This bar code sets the baud rate  
to 2400 bps and the data format to 7 data bits, even parity, 2 stop bits. It also adds a carriage return (CR) suffix and pro-  
grams the following prefixes for each symbology:  
Symbology  
Prefix  
UPC-A  
UPC-E  
EAN-8  
EAN-13  
A
E0  
FF  
F
Gilbarco Settings  
Honeywell Bioptic Aux Port Configuration  
Scan the following Plug and Play code to program the scan engine for a Honeywell bioptic scanner auxiliary port configura-  
tion. This bar code sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit.  
Honeywell Bioptic Settings  
Datalogic™ Magellan® Aux Port Configuration  
Scan the following Plug and Play code to program the scan engine for a Datalogic Magellan auxiliary port configuration.  
This bar code sets the baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit.  
Datalogic Magellan Settings  
NCR Bioptic Aux Port Configuration  
Scan the following Plug and Play code to program the scan engine for an NCR bioptic scanner auxiliary port configuration.  
The following prefixes are programmed for each symbology:  
Symbology  
Prefix  
Symbology  
Prefix  
UPC-A  
UPC-E  
EAN-8  
A
E0  
FF  
Code 39  
B1  
B2  
B3  
Interleaved 2 of 5  
All other bar  
codes  
EAN-13  
F
NCR Bioptic Settings  
2 - 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Wincor Nixdorf Terminal Default Settings  
Scan the following Plug and Play code to program the scan engine for a Wincor Nixdorf terminal. This bar code sets the  
baud rate to 9600 bps and the data format to 8 data bits, no parity, 1 stop bit.  
Wincor Nixdorf Terminal Settings  
Wincor Nixdorf Beetle™ Terminal Default Settings  
Scan the following Plug and Play code to program the scan engine for a Wincor Nixdorf Beetle terminal. The following pre-  
fixes are programmed for each symbology:  
Symbology  
Prefix  
Symbology  
EAN-13  
GS1-128  
Interleaved 2 of 5  
Straight 2 of 5 IATA  
All other bar codes  
Prefix  
Code 128  
Code 93  
Codabar  
UPC-A  
UPC-E  
EAN-8  
K
L
N
A0  
C
B
A
P
I
H
M
Wincor Nixdorf Beetle Settings  
Keyboard Country Layout  
Scan the appropriate country code below to program the keyboard layout for your country or language. As a general rule, the  
following characters are supported, but need special care for countries other than the United States:  
@ | $ # { } [ ] = / ‘ \ < > ~  
Keyboard Countries  
* United States  
Albania  
Azeri (Cyrillic)  
Azeri (Latin)  
2 - 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Keyboard Countries (Continued)  
Belarus  
Belgium  
Bosnia  
Brazil  
Brazil (MS)  
Bulgaria (Cyrillic)  
Canada (French legacy)  
Canada (Multilingual)  
Bulgaria (Latin)  
Canada (French)  
Croatia  
2 - 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Keyboard Countries (Continued)  
Czech  
Czech (QWERTY)  
Denmark  
Czech (Programmers)  
Czech (QWERTZ)  
Dutch (Netherlands)  
Faroese  
Estonia  
Finland  
France  
Gaelic  
2 - 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Keyboard Countries (Continued)  
Germany  
Greek  
Greek (220 Latin)  
Greek (319 Latin)  
Greek (Latin)  
Greek (220)  
Greek (319)  
Greek (MS)  
Hebrew  
Greek (Polytonic)  
Hungarian (101 key)  
2 - 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Keyboard Countries (Continued)  
Hungary  
Iceland  
Italian (142)  
Japan ASCII  
Kyrgyz (Cyrillic)  
Latvia  
Irish  
Italy  
Kazakh  
Latin America  
Latvia (QWERTY)  
2 - 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Keyboard Countries (Continued)  
Lithuania  
Lithuania (IBM)  
Macedonia  
Malta  
Mongolian (Cyrillic)  
Norway  
Poland  
Polish (Programmers)  
Romania  
Polish (214)  
Portugal  
2 - 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Keyboard Countries (Continued)  
Russia  
Russian (MS)  
Russian (Typewriter)  
Serbia (Cyrillic)  
Slovakia  
SCS  
Serbia (Latin)  
Slovakia (QWERTY)  
Slovenia  
Slovakia (QWERTZ)  
Spain  
2 - 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Keyboard Countries (Continued)  
Spanish variation  
Sweden  
Switzerland (German)  
Turkey F  
Switzerland (French)  
Tatar  
Turkey Q  
Ukrainian  
United Kingdom  
United States (Dvorak)  
United States (Dvorak left)  
2 - 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Keyboard Countries (Continued)  
United Stated (Dvorak right)  
United States (International)  
Uzbek (Cyrillic)  
Keyboard Style  
This programs keyboard styles, such as Caps Lock and Shift Lock. If you have used Keyboard Conversion settings, they will  
override any of the following Keyboard Style settings. Default = Regular.  
Regular is used when you normally have the Caps Lock key off.  
* Regular  
Caps Lock is used when you normally have the Caps Lock key on.  
Caps Lock  
Shift Lock is used when you normally have the Shift Lock key on (not common to U.S. keyboards).  
Shift Lock  
Automatic Caps Lock is used if you change the Caps Lock key on and off. The software tracks and reflects if you have Caps  
Lock on or off . This selection can only be used with systems that have an LED that notes the Caps Lock status (AT keyboards).  
Automatic Caps Lock  
Autocaps via NumLock bar code should be scanned in countries (e.g., Germany, France) where the Caps Lock key cannot be  
used to toggle Caps Lock. The NumLock option works similarly to the regular Autocaps, but uses the NumLock key to retrieve  
the current state of the Caps Lock.  
Autocaps via NumLock  
2 - 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent).  
Emulate External Keyboard  
Note: After scanning the Emulate External Keyboard bar code, you must power cycle your computer.  
Keyboard Conversion  
Alphabetic keyboard characters can be forced to be all upper case or all lowercase. So if you have the following bar code:  
“abc569GK,” you can make the output “ABC569GK” by scanning Convert All Characters to Upper Case, or to “abc569gk” by  
scanning Convert All Characters to Lower Case.  
These settings override Keyboard Style selections.  
Note: If your interface is a keyboard wedge, first scan the menu code for Automatic Caps Lock (page 2-13). Otherwise, your  
output may not be as expected.  
Default = Keyboard Conversion Off.  
* Keyboard Conversion Off  
Convert All Characters  
to Upper Case  
Convert All Characters  
to Lower Case  
Control Character Output  
This selection sends a text string instead of a control character. For example, when the control character for a carriage return is  
expected, the output would display [CR] instead of the ASCII code of 0D. Refer to ASCII Conversion Chart (Code Page  
1252) on page A-3. Only codes 00 through 1F are converted (the first column of the chart).  
Note: Control + X (Control + ASCII) Mode overrides this mode.  
Default = Off.  
Control Character Output On  
* Control Character Output Off  
2 - 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Keyboard Modifiers  
This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode.  
Control + X (Control + ASCII) Mode On: The scan engine sends key combinations for ASCII control characters for values 00-  
1F. Windows is the preferred mode. All keyboard country codes are supported. DOS mode is a legacy mode, and it does not  
support all keyboard country codes. New users should use the Windows mode. Refer to Keyboard Function  
Relationships, page 8-1 for CTRL+ X Values.  
Windows Mode Prefix/Suffix Off: The scan engine sends key combinations for ASCII control characters for values 00-1F, but  
it does not translate any prefix or suffix information.  
Default = Control + X Mode Off.  
Windows Mode Control + X  
Mode On  
* Control + X Mode Off  
DOS Mode Control + X Mode On  
Windows Mode Prefix/Suffix Off  
Turbo Mode: The scan engine sends characters to a terminal faster. If the terminal drops characters, do not use Turbo Mode.  
Default = Off.  
Turbo Mode On  
* Turbo Mode Off  
Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off.  
Numeric Keypad Mode On  
* Numeric Keypad Mode Off  
2 - 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping  
characters. Default = Off.  
Automatic Direct Connect Mode  
On  
* Automatic Direct Connect  
Mode Off  
RS232 Modifiers  
RS232 Baud Rate  
Baud Rate sends the data from the scan engine to the terminal at the specified rate. The host terminal must be set for the  
same baud rate as the engine. Default = 9600.  
300  
600  
1200  
2400  
4800  
* 9600  
19200  
2 - 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
38400  
57,600  
115,200  
RS232 Word Length: Data Bits, Stop Bits, and Parity  
Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0  
through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications that require use of the full ASCII set,  
select 8 data bits per character. Default = 8.  
Stop Bits sets the stop bits at 1 or 2. Default = 1.  
Parity provides a means of checking character bit patterns for validity.  
Default = None.  
7 Data, 1 Stop, Parity Even  
7 Data, 1 Stop, Parity None  
7 Data, 1 Stop, Parity Odd  
7 Data, 2 Stop, Parity Even  
7 Data, 2 Stop Parity None  
7 Data, 2 Stop, Parity Odd  
2 - 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
8 Data, 1 Stop, Parity Even  
* 8 Data, 1 Stop, Parity None  
8 Data, 1 Stop, Parity Odd  
8 Data, 1 Stop, Parity Mark  
RS232 Receiver Time-Out  
The unit stays awake to receive data until the RS232 Receiver Time-Out expires. A manual or serial trigger resets the time-  
out. When an RS232 receiver is sleeping, a character may be sent to wake up the receiver and reset the time-out. A trans-  
action on the CTS line will also wake up the receiver. The receiver takes 300 milliseconds to completely come up. Change  
the RS232 receiver time-out by scanning the bar code below, then scanning digits from the inside back cover of this man-  
ual, then scanning Save. The range is 0 to 300 seconds. Default = 0 seconds (no time-out - always on).  
RS232 Receiver Time-Out  
RS232 Handshaking  
RS232 Handshaking allows control of data transmission from the scan engine using software commands from the host  
device. When RTS/CTS is turned Off, no data flow control is used.  
Flow Control, No Timeout: The scan engine asserts RTS when it has data to send, and will wait indefinitely for CTS to be  
asserted by the host.  
Two-Direction Flow Control: The scan engine asserts RTS when it is OK for the host to transmit. The host asserts CTS  
when it is OK for the device to transmit.  
Flow Control with Timeout: The scan engine asserts RTS when it has data to send and waits for a delay (see RS232  
Timeout on page 2-19) for CTS to be asserted by the host. If the delay time expires and CTS is not asserted, the device  
transmit buffer is cleared and scanning may resume.  
Default = RTS/CTS Off.  
Flow Control, No Timeout  
Two-Direction Flow Control  
2 - 18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Flow Control with Timeout  
* RTS/CTS Off  
RS232 Timeout  
When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host.  
Set the length (in milliseconds) for a timeout by scanning the bar code below, then setting the timeout (from 1-5100 millisec-  
onds) by scanning digits from the inside back cover, then scanning Save.  
RS232 Timeout  
XON/XOFF  
Standard ASCII control characters can be used to tell the scan engine to start sending data (XON/XOFF On) or to stop  
sending data (XON/XOFF Off). When the host sends the XOFF character (DC3, hex 13) to the scan engine, data transmis-  
sion stops. To resume transmission, the host sends the XON character (DC1, hex 11). Data transmission continues where  
it left off when XOFF was sent. Default = XON/XOFF Off.  
XON/XOFF On  
* XON/XOFF Off  
ACK/NAK  
After transmitting data, the scan engine waits for an ACK character (hex 06) or a NAK character (hex 15) response from the  
host. If ACK is received, the communications cycle is completed and the scan engine looks for more bar codes. If NAK is  
received, the last set of bar code data is retransmitted and the scan engine waits for ACK/NAK again. Turn on the ACK/  
NAK protocol by scanning the ACK/NAK On bar code below. To turn off the protocol, scan ACK/NAK Off. Default = ACK/  
NAK Off.  
ACK/NAK On  
* ACK/NAK Off  
2 - 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
RS232 Stop Mode  
Scan the following bar code to force the engine into a stop mode. Restart the engine by using a trigger pull, nWake, or RxD  
toggle.  
RS232 Stop Mode On  
Scanner to Bioptic Communication  
The following settings are used to set up communication between Honeywell scanners and bioptic scanners.  
Note: The scan engine’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate  
with a bioptic scanner. See "RS232 Modifiers" on page 2-16, and RS232 Timeout on page 2-19 for further information.  
Scanner-Bioptic Packet Mode  
Packet Mode On must be scanned to set the scan engine’s format so it is compatible with a bioptic scanner. Default =  
Packet Mode Off.  
* Packet Mode Off  
Packet Mode On  
Scanner-Bioptic ACK/NAK Mode  
Bioptic ACK/Nak On must be scanned so the scan engine will wait for an ACK or NAK from a bioptic scanner after each  
packet is sent. The Scanner-Bioptic ACK/NAK Timeout (below) controls how long the scan engine will wait for a response.  
Default = Bioptic ACK/NAK Off.  
* Bioptic ACK/NAK Off  
Bioptic ACK/NAK On  
2 - 20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Scanner-Bioptic ACK/NAK Timeout  
This allows you to set the length (in milliseconds) for a timeout for a bioptic scanner’s ACK/NAK response. Scan the bar  
code below, then set the timeout (from 1-30,000 milliseconds) by scanning digits from the inside back cover, then scanning  
Save. Default = 5100.  
ACK/NAK Timeout  
2 - 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
2 - 22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Input/Output Settings  
Power Up Beeper  
The scan engine can be programmed to beep when it’s powered up. Scan the Off bar code(s) if you don’t want a power up  
beep. Default = Power Up Beeper On - Scanner.  
Power Up Beeper Off -  
Scanner  
* Power Up Beeper On -  
Scanner  
Beep on BEL Character  
You may wish to force the scan engine to beep upon a command sent from the host. If you scan the Beep on BEL On bar code  
below, the scan engine will beep every time a BEL character is received from the host. Default = Beep on BEL Off.  
*Beep on BEL Off  
Beep on BEL On  
Trigger Click  
To hear an audible click every time the scanner trigger is pressed, scan the Trigger Click On bar code below. Scan the Trigger  
Click Off code if you don’t wish to hear the click. (This feature has no effect on serial or automatic triggering.) Default = Trigger  
Click Off.  
*Trigger Click Off  
Trigger Click On  
3 - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Good Read and Error Indicators  
Beeper – Good Read  
The beeper may be programmed On or Off in response to a good read. Turning this option off only turns off the beeper  
response to a good read indication. All error and menu beeps are still audible. Default = Beeper - Good Read On.  
Beeper - Good Read Off  
* Beeper - Good Read On  
Beeper Volume – Good Read  
The beeper volume codes modify the volume of the beep the scan engine emits on a good read. Default = High.  
Low  
Medium  
* High  
Off  
Beeper Pitch – Good Read  
The beeper pitch codes modify the pitch (frequency) of the beep the scan engine emits on a good read. Default = Medium.  
Low (1600 Hz)  
* Medium (2700 Hz)  
3 - 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
High (4200 Hz)  
Beeper Pitch – Error  
The beeper pitch codes modify the pitch (frequency) of the sound the scan engine emits when there is a bad read or error.  
Default = Razz.  
* Razz (250 Hz)  
Medium (3250 Hz)  
High (4200 Hz)  
Beeper Duration – Good Read  
The beeper duration codes modify the length of the beep the scan engine emits on a good read. Default = Normal.  
* Normal Beep  
Short Beep  
LED – Good Read  
The LED indicator can be programmed On or Off in response to a good read. Default = On.  
* LED - Good Read On  
LED - Good Read Off  
3 - 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Number of Beeps – Good Read  
The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the  
beeper and LED in response to a good read. For example, if you program this option to have five beeps, there will be five  
beeps and five LED flashes in response to a good read. The beeps and LED flashes are in sync with one another. To  
change the number of beeps, scan the bar code below and then scan a digit (1-9) bar code and the Save bar code on the  
Programming Chart inside the back cover of this manual. Default = 1.  
Number of Good Read Beeps/LED Flashes  
Number of Beeps – Error  
The number of beeps and LED flashes emitted by the scan engine for a bad read or error can be programmed from 1 - 9.  
For example, if you program this option to have five error beeps, there will be five error beeps and five LED flashes in  
response to an error. To change the number of error beeps, scan the bar code below and then scan a digit (1-9) bar code  
and the Save bar code on the Programming Chart inside the back cover of this manual. Default = 1.  
Number of Error Beeps/LED Flashes  
Good Read Delay  
This sets the minimum amount of time before the scan engine can read another bar code. Default = 0 ms (No Delay).  
* No Delay  
Short Delay (500 ms)  
Medium Delay (1,000 ms)  
Long Delay (1,500 ms)  
User-Specified Good Read Delay  
If you want to set your own length for the good read delay, scan the bar code below, then set the delay (from 0 - 30,000 mil-  
liseconds) by scanning digits from the inside back cover, then scanning Save.  
User-Specified Good Read Delay  
3 - 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Manual Trigger Modes  
When in manual trigger mode, the scan engine scans until a bar code is read, or until the trigger is released. Two modes are  
available, Normal and Enhanced. Normal mode offers good scan speed and the longest working ranges (depth of field).  
Enhanced mode will give you the highest possible scan speed but slightly less range than Normal mode. Enhanced mode is  
best used when you require a very fast scan speed and don’t require a long working range. Default = Manual Trigger-Normal.  
* Manual Trigger - Normal  
Manual Trigger - Enhanced  
Serial Trigger Mode  
You can activate the scan engine either by pressing the trigger, or using a serial trigger command (see Trigger Commands on  
page 10-3). When in serial mode, the scan engine scans until a bar code has been read or until the deactivate command is  
sent. The scan engine can also be set to turn itself off after a specified time has elapsed (see Read Time-Out, which follows).  
Read Time-Out  
Use this selection to set a time-out (in milliseconds) of the scan engine’s trigger when using serial commands to trigger the  
scan engine. Once the scan engine has timed out, you can activate the scan engine either by pressing the trigger or using  
a serial trigger command. After scanning the Read Time-Out bar code, set the time-out duration (from 0-300,000 millisec-  
onds) by scanning digits on the Programming Chart inside the back cover, then scanning Save. Default = 30,000 ms.  
Read Time-Out  
Presentation Mode  
Presentation Mode uses ambient light and scan engine illumination to detect bar codes. When in Presentation Mode, the LEDs  
remain dim until a bar code is presented to the scan engine, then the aimer turns on and the LEDs turn up to read the code. If  
the light level in the room is not high enough, Presentation Mode may not work properly.  
Scan the following bar code to program your scan engine for Presentation Mode.  
Presentation Mode  
3 - 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
LED Illumination - Presentation Mode  
If you wish to set the illumination LED brightness, scan one of the bar codes below. This sets the LED illumination for the  
scan engine when it is in Presentation Mode. (If the scan engine is triggered manually, the LED illumination will switch to  
the setting for a manual trigger. Default = High.  
Note: The LEDs are like a flash on a camera. The lower the ambient light in the room, the brighter the LEDs need to be so  
the scan engine can “see” the bar codes.  
Off  
Low  
* High  
Note: LED Illumination - Presentation Mode does not apply to Streaming Presentation™ Mode or Mobile Phone Read  
Mode.  
Presentation LED Behavior after Decode  
When a scan engine is in presentation mode, the LEDs dim 30 seconds after a bar code is decoded. If you wish to dim the  
LEDs immediately after a bar code is decoded, scan the LEDs Off bar code, below. Default = LEDs On.  
* LEDs On  
LEDs Off  
Presentation Sensitivity  
Presentation Sensitivity is a numeric range that increases or decreases the scan engine's reaction time to bar code presen-  
tation. To set the sensitivity, scan the Sensitivity bar code, then scan the degree of sensitivity (from 0-20) from the inside  
back cover, and Save. 0 is the most sensitive setting, and 20 is the least sensitive. Default = 1.  
Sensitivity  
3 - 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Streaming Presentation™ Mode  
When in Streaming Presentation mode, the scan engine’s aimer goes out after a short time, but the scan illumination remains  
on all the time to continuously search for bar codes. Two modes are available, Normal and Enhanced. Normal mode offers  
good scan speed and the longest working ranges (depth of field). Enhanced mode will give you the highest possible scan  
speed but slightly less range than Normal mode. Enhanced mode is best used when you require a very fast scan speed and  
don’t require a long working range.  
Streaming Presentation Mode  
- Normal  
Streaming Presentation Mode  
- Enhanced  
When using Preferred Symbology (page 3-12), a lower priority symbol must be centered on the aiming pattern to be read in  
Streaming Presentation Mode.  
Mobile Phone Read Mode  
When this mode is selected, your scan engine is optimized to read bar codes from mobile phone or other LED displays. How-  
ever, the speed of scanning printed bar codes may be slightly lower when this mode is enabled. You can enable Mobile Phone  
Reading for either a hand held device, or for a hands-free (presentation) application.  
Hand Held Scanning - Mobile  
Phone  
Streaming Presentation -  
Mobile Phone  
Note: To turn off Mobile Phone Read Mode, scan a Manual or Serial Trigger Mode bar code (see page 3-5).  
Image Snap and Ship  
Image Snap and Ship tells the engine to take a picture (rather than read a bar code) when the trigger is pressed. Once the pic-  
ture is snapped, it is shipped to the host system as a jpeg file by default. To revert to bar code reading, you must change to a  
different trigger mode (see Manual Trigger Modes beginning on page 3-5).  
Image Snap and Ship  
Note: You must send a serial command for Manual Trigger Modes (see page 3-5) in order to use menu codes after using Image  
Snap and Ship  
3 - 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Hands Free Time-Out  
The Scan Stand and Presentation Modes are referred to as “hands free” modes. If the scanner’s trigger is pulled when using a  
hands free mode, the scanner changes to manual trigger mode. You can set the time the scanner should remain in manual trig-  
ger mode by setting the Hands Free Time-Out. Once the time-out value is reached, (if there have been no further trigger pulls)  
the scanner reverts to the original hands free mode.  
Scan the Hands Free Time-Out bar code, then scan the time-out duration (from 0-300,000 milliseconds) from the inside back  
cover, and Save. Default = 5,000 ms.  
Hands Free Time-Out  
Reread Delay  
This sets the time period before the scan engine can read the same bar code a second time. Setting a reread delay protects  
against accidental rereads of the same bar code. Longer delays are effective in minimizing accidental rereads. Use shorter  
delays in applications where repetitive bar code scanning is required. Reread Delay only works when in a Presentation Mode  
(see page 3-5). Default = Medium.  
Short (500 ms)  
* Medium (750 ms)  
Long (1000 ms)  
Extra Long (2000 ms)  
User-Specified Reread Delay  
If you want to set your own length for the reread delay, scan the bar code below, then set the delay (from 0-30,000 millisec-  
onds) by scanning digits from the inside back cover, then scanning Save.  
User-Specified Reread Delay  
3 - 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
2D Reread Delay  
Sometimes 2D bar codes can take longer to read than other bar codes. If you wish to set a separate Reread Delay for 2D  
bar codes, scan one of the programming codes that follows. 2D Reread Delay Off indicates that the time set for Reread  
Delay is used for both 1D and 2D bar codes. Default = 2D Reread Delay Off.  
* 2D Reread Delay Off  
Short (1000ms)  
Medium (2000ms)  
Long (3000ms)  
Extra Long (4000ms)  
Illumination Lights  
If you want the illumination lights on while reading a bar code, scan the Lights On bar code, below. However, if you want to turn  
just the lights off, scan the Lights Off bar code. Default = Lights On.  
Note: This setting does not affect the aimer light. The aiming light can be set using Aimer Mode (page 3-10).  
* Lights On  
Lights Off  
3 - 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Aimer Delay  
The aimer delay allows a delay time for the operator to aim the scan engine before the picture is taken. Use these codes to set  
the time between when the trigger is pulled and when the picture is taken. During the delay time, the aiming light will appear,  
but the LEDs won’t turn on until the delay time is over. Default = Off.  
200 milliseconds  
400 milliseconds  
* Off (no delay)  
User-Specified Aimer Delay  
If you want to set your own length for the duration of the delay, scan the bar code below, then set the time-out by scanning  
digits (0 - 4,000 ms) from the Programming Chart inside the back cover of this manual, then scan Save.  
Delay Duration  
Aimer Mode  
This feature allows you to turn the aimer on and off. When the Interlaced bar code is scanned, the aimer is interlaced with the  
illumination LEDs. Default = Interlaced.  
Off  
* Interlaced  
Centering  
Use Centering to narrow the scan engine’s field of view to make sure that when the scanner is hand-held, it reads only those bar  
codes intended by the user. For instance, if multiple codes are placed closely together, centering will insure that only the  
desired codes are read. (Centering can be used in conjunction with Aimer Delay, page 3-10, for the most error-free operation  
in applications where multiple codes are spaced closely together. Using the Aimer Delay and Centering features, the scanner  
can emulate the operation of older systems, such as linear laser bar code scanners.).  
If a bar code is not touched by a predefined window, it will not be decoded or output by the scan engine. If centering is turned  
on by scanning Centering On, the scan engine only reads codes that pass through the centering window you specify using the  
Top of Centering Window, Bottom of Centering Window, Left, and Right of Centering Window bar codes.  
3 - 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top,  
and 25% bottom. Since Bar Code 1 passes through the centering window, it will be read. Bar Code 2 does not pass through  
the centering window, so it will not be read.  
0%  
Bar Code 1  
10  
Bar Code 2  
20  
30  
40  
50  
60  
70  
80  
90  
100  
0
10  
20  
30  
40  
50  
60  
70  
80  
90  
100%  
Note: A bar code needs only to be touched by the centering window in order to be read. It does not need to pass completely  
through the centering window.  
Scan Centering On, then scan one of the following bar codes to change the top, bottom, left, or right of the centering window.  
Then scan the percent you want to shift the centering window using digits on the inside back cover of this manual. Scan Save.  
Default Centering = 40% for Top and Left, 60% for Bottom and Right.  
Centering On  
* Centering Off  
Top of Centering Window  
Bottom of Centering Window  
3 - 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Preferred Symbology  
The scan engine can be programmed to specify one symbology as a higher priority over other symbologies in situations where  
both bar code symbologies appear on the same label, but the lower priority symbology cannot be disabled.  
For example, you may be using the scanner in a retail setting to read U.P.C. symbols, but have occasional need to read a code  
on a drivers license. Since some licenses have a Code 39 symbol as well as the PDF417 symbol, you can use Preferred Sym-  
bology to specify that the PDF417 symbol be read instead of the Code 39.  
Preferred Symbology classifies each symbology as high priority, low priority, or as an unspecified type. When a low priority  
symbology is presented, the scanner ignores it for a set period of time (see Preferred Symbology Time-out on page 3-13) while  
it searches for the high priority symbology. If a high priority symbology is located during this period, then that data is read imme-  
diately.  
If the time-out period expires before a high priority symbology is read, the scanner will read any bar code in its view (low priority  
or unspecified). If there is no bar code in the scanner’s view after the time-out period expires, then no data is reported.  
Note: A low priority symbol must be centered on the aiming pattern to be read.  
Scan a bar code below to enable or disable Preferred Symbology. Default = Preferred Symbology Off.  
Preferred Symbology On  
* Preferred Symbology Off  
High Priority Symbology  
To specify the high priority symbology, scan the High Priority Symbology bar code below. On the Symbology Charts on  
page A-1, find the symbology you want to set as high priority. Locate the Hex value for that symbology and scan the 2 digit  
hex value from the Programming Chart (inside back cover). Scan Save to save your selection. Default = None  
High Priority Symbology  
Low Priority Symbology  
To specify the low priority symbology, scan the Low Priority Symbology bar code below. On the Symbology Charts on page  
A-1, find the symbology you want to set as low priority. Locate the Hex value for that symbology and scan the 2 digit hex  
value from the Programming Chart (inside back cover).  
If you want to set additional low priority symbologies, scan FF, then scan the 2 digit hex value from the Programming Chart  
for the next symbology. You can program up to 5 low priority symbologies. Scan Save to save your selection. Default =  
None.  
Low Priority Symbology  
3 - 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Preferred Symbology Time-out  
Once you have enabled Preferred Symbology and entered the high and low priority symbologies, you must set the time-out  
period. This is the period of time the scan engine will search for a high priority bar code after a low priority bar code has  
been encountered. Scan the bar code below, then set the delay (from 1-3,000 milliseconds) by scanning digits from the  
inside back cover, then scanning Save. Default = 500 ms.  
Preferred Symbology Time-out  
Preferred Symbology Default  
Scan the bar code below to set all Preferred Symbology entries to their default values.  
Preferred Symbology Default  
Output Sequence Overview  
Output Sequence Editor  
This programming selection allows you to program the scan engine to output data (when scanning more than one symbol)  
in whatever order your application requires, regardless of the order in which the bar codes are scanned. Reading the  
Default Sequence symbol programs the scan engine to the Universal values, shown below. These are the defaults. Be  
certain you want to delete or clear all formats before you read the Default Sequence symbol.  
Note: To make Output Sequence Editor selections, you’ll need to know the code I.D., code length, and character match(es)  
your application requires. Use the Alphanumeric symbols (inside back cover) to read these options. You must hold  
the trigger while reading each bar code in the sequence.  
To Add an Output Sequence  
1. Scan the Enter Sequence symbol (see Require Output Sequence, page 3-15).  
2. Code I.D.  
On the Symbology Charts on page A-1, find the symbology to which you want to apply the output sequence format.  
Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart (inside back  
cover).  
3. Length  
Specify what length (up to 9999 characters) of data output will be acceptable for this symbology. Scan the four digit  
data length from the Programming Chart. (Note: 50 characters is entered as 0050. 9999 is a universal number,  
indicating all lengths.) When calculating the length, you must count any programmed prefixes, suffixes, or formatted  
characters as part of the length (unless using 9999).  
4. Character Match Sequences  
On the ASCII Conversion Chart (Code Page 1252), page A-3, find the Hex value that represents the character(s) you  
want to match. Use the Programming Chart to read the alphanumeric combination that represents the ASCII  
characters. (99 is the Universal number, indicating all characters.)  
5. End Output Sequence Editor  
Scan F F to enter an Output Sequence for an additional symbology, or Save to save your entries.  
Other Programming Selections  
•
Discard  
This exits without saving any Output Sequence changes.  
3 - 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Output Sequence Example  
In this example, you are scanning Code 93, Code 128, and Code 39 bar codes, but you want the scanner to output Code 39  
1st, Code 128 2nd, and Code 93 3rd, as shown below.  
Note: Code 93 must be enabled to use this example.  
A - Code 39  
B - Code 128  
C - Code 93  
You would set up the sequence editor with the following command line:  
SEQBLK62999941FF6A999942FF69999943FF  
The breakdown of the command line is shown below:  
SEQBLKsequence editor start command  
62  
code identifier for Code 39  
9999  
41  
code length that must match for Code 39, 9999 = all lengths  
start character match for Code 39, 41h = “A”  
termination string for first code  
FF  
6A  
code identifier for Code 128  
9999  
42  
code length that must match for Code 128, 9999 = all lengths  
start character match for Code 128, 42h = “B”  
termination string for second code  
FF  
69  
code identifier for Code 93  
9999  
43  
code length that must match for Code 93, 9999 = all lengths  
start character match for Code 93, 43h = “C”  
termination string for third code  
FF  
To program the previous example using specific lengths, you would have to count any programmed prefixes, suffixes, or for-  
matted characters as part of the length. If you use the example on page 3-14, but assume a <CR> suffix and specific code  
lengths, you would use the following command line:  
SEQBLK62001241FF6A001342FF69001243FF  
The breakdown of the command line is shown below:  
SEQBLKsequence editor start command  
62  
code identifier for Code 39  
0012  
41  
A - Code 39 sample length (11) plus CR suffix (1) = 12  
start character match for Code 39, 41h = “A”  
termination string for first code  
FF  
6A  
code identifier for Code 128  
0013  
42  
B - Code 128 sample length (12) plus CR suffix (1) = 13  
start character match for Code 128, 42h = “B”  
3 - 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
FF  
termination string for second code  
69  
code identifier for Code 93  
0012  
43  
C - Code 93 sample length (11) plus CR suffix (1) = 12  
start character match for Code 93, 43h = “C”  
termination string for third code  
FF  
Output Sequence Editor  
Enter Sequence  
Default Sequence  
Partial Sequence  
If an output sequence operation is terminated before all your output sequence criteria are met, the bar code data acquired  
to that point is a “partial sequence.”  
Scan Discard Partial Sequence to discard partial sequences when the output sequence operation is terminated before  
completion. Scan Transmit Partial Sequence to transmit partial sequences. (Any fields in the sequence where no data  
match occurred will be skipped in the output.)  
Transmit Partial Sequence  
* Discard Partial Sequence  
Require Output Sequence  
When an output sequence is Required, all output data must conform to an edited sequence or the scan engine will not  
transmit the output data to the host device. When it’s On/Not Required, the scan engine will attempt to get the output data  
to conform to an edited sequence but, if it cannot, the scan engine transmits all output data to the host device as is.  
When the output sequence is Off, the bar code data is output to the host as the scan engine decodes it. Default = Off.  
Note: This selection is unavailable when the Multiple Symbols Selection is turned on.  
Required  
On/Not Required  
3 - 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
*Off  
Multiple Symbols  
When this programming selection is turned On, it allows you to read multiple symbols with a single pull of the scanner’s trigger.  
If you press and hold the trigger, aiming the scanner at a series of symbols, it reads unique symbols once, beeping (if turned on)  
for each read. The scanner attempts to find and decode new symbols as long as the trigger is pulled. When this programming  
selection is turned Off, the scanner will only read the symbol closest to the aiming beam. Default = Off.  
On  
* Off  
No Read  
With No Read turned On, the scan engine notifies you if a code cannot be read. If using an EZConfig-Scanning Tool Scan Data  
Window (see page 9-3), an “NR” appears when a code cannot be read. If No Read is turned Off, the “NR” will not appear.  
Default = Off.  
On  
* Off  
If you want a different notation than “NR,” for example, “Error,” or “Bad Code,” you can edit the output message (see Data  
Formatting beginning on page 5-1). The hex code for the No Read symbol is 9C.  
Video Reverse  
Video Reverse is used to allow the scan engine to read bar codes that are inverted. The Video Reverse Off bar code below is  
an example of this type of bar code. Scan Video Reverse Only to read only inverted bar codes. Scan Video Reverse and  
Standard Bar Codes to read both types of codes.  
Note: After scanning Video Reverse Only, menu bar codes cannot be read. You must scan Video Reverse Off or Video  
Reverse and Standard Bar Codes in order to read menu bar codes.  
Note: Images downloaded from the unit are not reversed. This is a setting for decoding only.  
Video Reverse Only  
3 - 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Video Reverse and Standard Bar  
Codes  
VIDREV0.  
* Video Reverse Off  
Working Orientation  
Some bar codes are direction-sensitive. For example, KIX codes and OCR can misread when scanned sideways or upside  
down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scan  
engine. Default = Upright.  
Upright:  
Vertical, Top to Bottom:  
(Rotate CW 90°)  
Upside Down:  
Vertical, Bottom to Top:  
(Rotate CCW 90°)  
* Upright  
Vertical, Bottom to Top  
Upside Down  
Vertical, Top to Bottom  
3 - 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
3 - 18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Data Editing  
Prefix/Suffix Overview  
When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar  
code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the  
user-defined data into the message string.  
Prefix and Suffix characters are data characters that can be sent before and after scanned data. You can specify if they should  
be sent with all symbologies, or only with specific symbologies. The following illustration shows the breakdown of a message  
string:  
Pre  
fi  
x
1-11  
alpha  
S
c
a
nned D  
a
num  
t
a
c
v
a
ria  
ble  
o
ntr  
eric &  
l charac  
o
leng  
Su  
ff  
i
x
th  
t
e
rs  
1-11  
alpha  
numeric &  
co  
n
t
ro  
l
char  
ac  
t
ers  
Points to Keep In Mind  
•
It is not necessary to build a message string. The selections in this chapter are only used if you wish to alter the default  
settings. Default prefix = None. Default suffix = None.  
•
•
A prefix or suffix may be added or cleared from one symbology or all symbologies.  
You can add any prefix or suffix from the ASCII Conversion Chart (Code Page 1252), beginning on page A-3, plus Code  
I.D. and AIM I.D.  
•
•
•
You can string together several entries for several symbologies at one time.  
Enter prefixes and suffixes in the order in which you want them to appear on the output.  
When setting up for specific symbologies (as opposed to all symbologies), the specific symbology ID value counts as an  
added prefix or suffix character.  
•
The maximum size of a prefix or suffix configuration is 200 characters, which includes header information.  
To Add a Prefix or Suffix:  
Step 1. Scan the Add Prefix or Add Suffix symbol (page 4-2).  
Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Symbology Charts, beginning on page  
A-1) for the symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and  
Hex ID is “6A”.  
Step 3. Scan the 2 hex digits from the Programming Chart inside the back cover of this manual or scan 9, 9 for all  
symbologies.  
Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page 1252), beginning on page A-3, for the prefix  
or suffix you wish to enter.  
Step 5. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual.  
Step 6. Repeat Steps 4 and 5 for every prefix or suffix character.  
Step 7. To add the Code I.D., scan 5, C, 8, 0.  
To add AIM I.D., scan 5, C, 8, 1.  
To add a backslash (\), scan 5, C, 5, C.  
Note: To add a backslash (\) as in Step 7, you must scan 5C twice – once to create the leading backslash and then to create  
the backslash itself.  
Step 8. Scan Save to exit and save, or scan Discard to exit without saving.  
Repeat Steps 1-6 to add a prefix or suffix for another symbology.  
Example: Add a Suffix to a specific symbology  
To send a CR (carriage return)Suffix for U.P.C. only:  
4 - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Step 1. Scan Add Suffix.  
Step 2. Determine the 2 digit hex value from the Symbology Chart (included in the Symbology Charts, beginning on page  
A-1) for U.P.C..  
Step 3. Scan 6, 3 from the Programming Chart inside the back cover of this manual.  
Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page 1252), beginning on page A-3, for the CR  
(carriage return).  
Step 5. Scan 0, D from the Programming Chart inside the back cover of this manual.  
Step 6. Scan Save, or scan Discard to exit without saving.  
To Clear One or All Prefixes or Suffixes  
You can clear a single prefix or suffix, or clear all prefixes/suffixes for a symbology. If you have been entering prefixes and  
suffixes for single symbologies, you can use Clear One Prefix (Suffix) to delete a specific character from a symbology.  
When you Clear All Prefixes (Suffixes), all the prefixes or suffixes for a symbology are deleted.  
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol.  
Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Symbology Charts, beginning on page  
A-1) for the symbology from which you want to clear the prefix or suffix.  
Step 3. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual or scan 9, 9 for all  
symbologies.  
Your change is automatically saved.  
To Add a Carriage Return Suffix to All Symbologies  
Scan the following bar code if you wish to add a carriage return suffix to all symbologies at once. This action first clears all  
current suffixes, then programs a carriage return suffix for all symbologies.  
Add CR Suffix  
All Symbologies  
Prefix Selections  
Add Prefix  
Clear One Prefix  
Clear All Prefixes  
4 - 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Suffix Selections  
Add Suffix  
Clear One Suffix  
Clear All Suffixes  
Function Code Transmit  
When this selection is enabled and function codes are contained within the scanned data, the scan engine transmits the func-  
tion code to the terminal. Charts of these function codes are provided in Supported Interface Keys starting on page 8-3. When  
the scanner is in keyboard wedge mode, the scan code is converted to a key code before it is transmitted. Default = Enable.  
* Enable  
Disable  
Intercharacter, Interfunction, and Intermessage Delays  
Some terminals drop information (characters) if data comes through too quickly. Intercharacter, interfunction, and intermessage  
delays slow the transmission of data, increasing data integrity.  
Intercharacter Delay  
An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each  
character of scanned data. Scan the Intercharacter Delay bar code below, then scan the number of 5ms delays, and the  
Save bar code using the Programming Chart inside the back cover of this manual.  
Prefix  
Scanned Data  
Suffix  
1
2
3
4
5
Intercharacter Delay  
Intercharacter Delay  
4 - 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
To remove this delay, scan the Intercharacter Delay bar code, then set the number of delays to 0. Scan the Save bar code  
using the Programming Chart inside the back cover of this manual.  
Note: Intercharacter delays are not supported in USB serial emulation.  
User Specified Intercharacter Delay  
An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed after the transmission of a particular  
character of scanned data. Scan the Delay Length bar code below, then scan the number of 5ms delays, and the Save  
bar code using the Programming Chart inside the back cover of this manual.  
Next, scan the Character to Trigger Delay bar code, then the 2-digit hex value for the ASCII character that will trigger the  
delay ASCII Conversion Chart (Code Page 1252), beginning on page A-3.  
Delay Length  
Character to Trigger Delay  
To remove this delay, scan the Delay Length bar code, and set the number of delays to 0. Scan the Save bar code using  
the Programming Chart inside the back cover of this manual.  
Interfunction Delay  
An interfunction delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each  
control character in the message string. Scan the Interfunction Delay bar code below, then scan the number of 5ms  
delays, and the Save bar code using the Programming Chart inside the back cover of this manual.  
Prefix  
STX  
Scanned Data  
3 4  
Interfunction Delays  
Suffix  
1
HT  
2
5
CR  
LF  
Interfunction Delay  
To remove this delay, scan the Interfunction Delay bar code, then set the number of delays to 0. Scan the Save bar code  
using the Programming Chart inside the back cover of this manual.  
4 - 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Intermessage Delay  
An intermessage delay of up to 5000 milliseconds (in 5ms increments) may be placed between each scan transmission.  
Scan the Intermessage Delay bar code below, then scan the number of 5ms delays, and the Save bar code using the  
Programming Chart inside the back cover of this manual.  
1st Scan Transmission  
2nd Scan Transmission  
Intermessage Delay  
Intermessage Delay  
To remove this delay, scan the Intermessage Delay bar code, then set the number of delays to 0. Scan the Save bar code  
using the Programming Chart inside the back cover of this manual.  
4 - 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
4 - 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
Data Formatting  
Data Format Editor Introduction  
You may use the Data Format Editor to change the scan engine’s output. For example, you can use the Data Format Editor to  
insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you  
wish to alter the output. Default Data Format setting = None.  
Normally, when you scan a bar code, it is output automatically. However, when you create a format, you must use a “send” com-  
mand (see Send Commands on page 5-3) within the format program to output data.  
Multiple formats may be programmed into the scan engine. They are stacked in the order in which they are entered. However,  
the following list presents the order in which formats are applied:  
1. Specific Terminal ID, Actual Code ID, Actual Length  
2. Specific Terminal ID, Actual Code ID, Universal Length  
3. Specific Terminal ID, Universal Code ID, Actual Length  
4. Specific Terminal ID, Universal Code ID, Universal Length  
5. Universal Terminal ID, Actual Code ID, Actual Length  
6. Universal Terminal ID, Actual Code ID, Universal Length  
7. Universal Terminal ID, Universal Code ID, Actual Length  
8. Universal Terminal ID, Universal Code ID, Universal Length  
The maximum size of a data format configuration is 2000 bytes, which includes header information.  
If a bar code is read that fails the first data format, the next data format, if there is one, will be used on the bar code data. If there  
is no other data format, the raw data is output.  
If you have changed data format settings, and wish to clear all formats and return to the factory defaults, scan the Default Data  
Format code below.  
* Default Data Format  
Add a Data Format  
Step 1. Scan the Enter Data Format symbol (page 5-2).  
Step 2. Select Primary/Alternate Format  
Determine if this will be your primary data format, or one of 3 alternate formats. This allows you to save a total of 4  
different data formats. To program your primary format, scan 0 using the Programming Chart inside the back cover of  
this manual. If you are programming an alternate format, scan 1, 2, or 3, depending on which alternate format you are  
programming. (See "Primary/Alternate Data Formats" on page 5-13 for further information.)  
Step 3. Terminal Type  
Refer to Terminal ID Table (page 5-3) and locate the Terminal ID number for your PC. Scan three numeric bar codes  
on the inside back cover to program the scan engine for your terminal ID (you must enter 3 digits). For example, scan  
0 0 3 for an AT wedge.  
Note: 099 indicates all terminal types.  
Step 4. Code I.D.  
In the Symbology Charts, beginning on page A-1, find the symbology to which you want to apply the data format. Locate  
the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart inside the back cover of  
this manual.  
If you wish to create a data format for all symbologies, with the exception of some specific symbologies, refer to B8  
(page 5-11).  
If you are creating a data format for Batch Mode Quantity, use 35 for the Code I.D.  
Note: 99 indicates all symbologies.  
5 - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Step 5. Length  
Specify what length (up to 9999 characters) of data will be acceptable for this symbology. Scan the four digit data length  
from the Programming Chart inside the back cover of this manual. For example, 50 characters is entered as 0050.  
Note: 9999 indicates all lengths.  
Step 6. Editor Commands  
Refer to Data Format Editor Commands (page 5-3). Scan the symbols that represent the command you want to enter.  
94 alphanumeric characters may be entered for each symbology data format.  
Step 7. Scan Save to save your data format, or Discard to exit without saving your changes.  
Enter Data Format  
Save  
Discard  
Other Programming Selections  
Clear One Data Format  
This deletes one data format for one symbology. If you are clearing the primary format, scan 0 from the Programming  
Chart inside the back cover of this manual. If you are clearing an alternate format, scan 1, 2, or 3, depending on the  
format you are clearing. Scan the Terminal Type and Code I.D. (see Symbology Charts on page A-1), and the bar code  
data length for the specific data format that you want to delete. All other formats remain unaffected.  
Clear all Data Formats  
This clears all data formats.  
Save to exit and save your data format changes.  
Discard to exit without saving any data format changes.  
Clear One Data Format  
Clear All Data Formats  
Save  
Discard  
5 - 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Terminal ID Table  
Terminal  
Model(s)  
Terminal ID  
IBM  
USB SurePOS Handheld Scanner  
USB SurePOS Tabletop Scanner  
True  
TTL  
128  
129  
000  
000  
051  
130  
124  
125  
134  
131  
RS232  
RS485  
USB  
Serial  
PC Keyboard  
Mac Keyboard  
Japanese Keyboard (PC)  
HID POS  
Data Format Editor Commands  
When working with the Data Format Editor, a virtual cursor is moved along your input data string. The following commands are  
used to both move this cursor to different positions, and to select, replace, and insert data into the final output.  
Send Commands  
Send all characters  
F1 Include in the output message all of the characters from the input message, starting from current cursor position,  
followed by an insert character. Syntax = F1xx where xx stands for the insert character’s hex value for its ASCII code.  
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.  
Send a number of characters  
F2 Include in the output message a number of characters followed by an insert character. Start from the current cursor  
position and continue for “nn” characters or through the last character in the input message, followed by character “xx.”  
Syntax = F2nnxx where nn stands for the numeric value (00-99) for the number of characters, and xx stands for the  
insert character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on  
page A-3 for decimal, hex and character codes.  
F2 Example: Send a number of characters  
Send the first 10 characters from the bar code above, followed by a carriage return. Command string: F2100D  
F2 is the “Send a number of characters” command  
10 is the number of characters to send  
0D is the hex value for a CR  
The data is output as: 1234567890  
F2 and F1 Example: Split characters into 2 lines  
Send the first 10 characters from the bar code above, followed by a carriage return, followed by the rest of the charac-  
ters.  
Command string: F2100DF10D  
F2 is the “Send a number of characters” command  
10 is the number of characters to send for the first line  
0D is the hex value for a CR  
F1 is the “Send all characters” command  
5 - 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
0D is the hex value for a CR  
The data is output as:  
1234567890  
ABCDEFGHIJ  
<CR>  
Send all characters up to a particular character  
F3 Include in the output message all characters from the input message, starting with the character at the current cursor  
position and continuing to, but not including, the search character “ss,” followed by an insert character. The cursor is  
moved forward to the “ss” character. Syntax = F3ssxx where ss stands for the search character’s hex value for its ASCII  
code, and xx stands for the insert character’s hex value for its ASCII code.  
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.  
F3 Example: Send all characters up to a particular character  
Using the bar code above, send all characters up to but not including “D,” followed by a carriage return.  
Command string: F3440D  
F3 is the “Send all characters up to a particular character” command  
44 is the hex value for a 'D”  
0D is the hex value for a CR  
The data is output as:  
1234567890ABC  
<CR>  
Send all characters up to a string  
B9 Include in the output message all characters from the input message, starting with the character at the current cursor  
position and continuing to, but not including, the search string “s...s.” The cursor is moved forward to the beginning of  
the “s...s” string. Syntax = B9nnnns...s where nnnn stands for the length of the string, and s...s stands for the string to  
be matched. The string is made up of hex values for the characters in the string. Refer to the ASCII Conversion Chart  
(Code Page 1252), beginning on page A-3 for decimal, hex and character codes.  
B9 Example: Send all characters up to a defined string  
Using the bar code above, send all characters up to but not including “AB.”  
Command string: B900024142  
B9 is the “Send all characters up to a string” command  
0002 is the length of the string (2 characters)  
41 is the hex value for A  
42 is the hex value for B  
The data is output as: 1234567890  
Send all but the last characters  
E9 Include in the output message all but the last “nn” characters, starting from the current cursor position. The cursor is  
moved forward to one position past the last input message character included. Syntax = E9nn where nn stands for the  
numeric value (00-99) for the number of characters that will not be sent at the end of the message.  
Insert a character multiple times  
F4 Send “xx” character “nn” times in the output message, leaving the cursor in the current position. Syntax = F4xxnn where  
xx stands for the insert character’s hex value for its ASCII code, and nn is the numeric value (00-99) for the number of  
times it should be sent. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal,  
hex and character codes.  
5 - 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
E9 and F4 Example: Send all but the last characters, followed by 2 tabs  
Send all characters except for the last 8 from the bar code above, followed by 2 tabs.  
Command string: E908F40902  
E9 is the “Send all but the last characters” command  
08 is the number of characters at the end to ignore  
F4 is the “Insert a character multiple times” command  
09 is the hex value for a horizontal tab  
02 is the number of times the tab character is sent  
The data is output as: 1234567890AB <tab><tab>  
Insert a string  
BA Send “ss” string of “nn” length in the output message, leaving the cursor in the current position. Syntax = BAnnnns...s  
where nnnn stands for the length of the string, and s...s stands for the string. The string is made up of hex values for  
the characters in the string. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal,  
hex and character codes.  
B9 and BA Example: Look for the string “AB” and insert 2 asterisks (**)  
Using the bar code above, send all characters up to but not including “AB.” Insert 2 asterisks at that point, and send  
the rest of the data with a carriage return after.  
Command string: B900024142BA00022A2AF10D  
B9 is the “Send all characters up to a string” command  
0002 is the length of the string (2 characters)  
41 is the hex value for A  
42 is the hex value for B  
BA is the “Insert a string” command  
0002 is the length of the string to be added (2 characters)  
2A is the hex value for an asterisk (*)  
2A is the hex value for an asterisk (*)  
F1 is the “Send all characters” command  
0D is the hex value for a CR  
The data is output as:  
1234567890**ABCDEFGHIJ  
<CR>  
Insert symbology name  
B3 Insert the name of the bar code’s symbology in the output message, without moving the cursor. Only symbologies with  
a Honeywell ID are included (see Symbology Charts on page A-1). Refer to the ASCII Conversion Chart (Code Page  
1252), beginning on page A-3 for decimal, hex and character codes.  
Insert bar code length  
B4 Insert the bar code’s length in the output message, without moving the cursor. The length is expressed as a numeric  
string and does not include leading zeroes.  
5 - 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B3 and B4 Example: Insert the symbology name and length  
Send the symbology name and length before the bar code data from the bar code above. Break up these insertions  
with spaces. End with a carriage return.  
Command string: B3F42001B4F42001F10D  
B3 is the “Insert symbology name” command  
F4 is the “Insert a character multiple times” command  
20 is the hex value for a space  
01 is the number of times the space character is sent  
B4 is the “Insert bar code length” command  
F4 is the “Insert a character multiple times” command  
20 is the hex value for a space  
01 is the number of times the space character is sent  
F1 is the “Send all characters” command  
0D is the hex value for a CR  
The data is output as:  
Code128 20 1234567890ABCDEFGHIJ  
<CR>  
Insert key strokes  
B5 Insert a key stroke or combination of key strokes. Key strokes are dependent on your keyboard (see Unicode Key Maps  
on page A-10). Any key can be inserted, including arrows and functions. Syntax = B5xxssnn where xx is the number  
of keys pressed (without key modifiers), ss is the key modifier from the table below, and nn is the key number from the  
Unicode Key Maps, page A-10.  
Key Modifiers  
No Key Modifier  
Shift Left  
00  
01  
02  
04  
08  
10  
20  
Shift Right  
Alt Left  
Alt Right  
Control Left  
Control Right  
For example, B501021F inserts an “A” on a 104 key, U.S. style keyboard. B5 = the command, 01 = number of keys  
pressed (without the key modifier), 02 is the key modifier for Shift Right, and 1F is the “a” key. If a lower case “a” were  
to be inserted, B501001F would be entered.  
If there are three keystrokes, the syntax would change from B5xxssnn for one keystroke to B5xxssnnssnnssnn. An  
example that would insert "abc" is as follows: B503001F00320030F833.  
Note: Key modifiers can be added together when needed. Example: Control Left+Shift Left = 11.  
Move Commands  
Move the cursor forward a number of characters  
F5 Move the cursor ahead “nn” characters from current cursor position.  
Syntax = F5nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved ahead.  
5 - 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
F5 Example: Move the cursor forward and send the data  
Move the cursor forward 3 characters, then send the rest of the bar code data from the bar code above. End with a  
carriage return.  
Command string: F503F10D  
F5 is the “Move the cursor forward a number of characters” command  
03 is the number of characters to move the cursor  
F1 is the “Send all characters” command  
0D is the hex value for a CR  
The data is output as:  
4567890ABCDEFGHIJ  
<CR>  
Move the cursor backward a number of characters  
F6 Move the cursor back “nn” characters from current cursor position.  
Syntax = F6nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved back.  
Move the cursor to the beginning  
F7 Move the cursor to the first character in the input message. Syntax = F7.  
FE and F7 Example: Manipulate bar codes that begin with a 1  
Search for bar codes that begin with a 1. If a bar code matches, move the cursor back to the beginning of the data and  
send 6 characters followed by a carriage return. Using the bar code above:  
Command string: FE31F7F2060D  
FE is the “Compare characters” command  
31 is the hex value for 1  
F7 is the “Move the cursor to the beginning” command  
F2 is the “Send a number of characters” command  
06 is the number of characters to send  
0D is the hex value for a CR  
The data is output as:  
123456  
<CR>  
Move the cursor to the end  
EA Move the cursor to the last character in the input message. Syntax = EA.  
Search Commands  
Search forward for a character  
F8 Search the input message forward for “xx” character from the current cursor position, leaving the cursor pointing to the  
“xx” character. Syntax = F8xx where xx stands for the search character’s hex value for its ASCII code.  
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.  
5 - 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
F8 Example: Send bar code data that starts after a particular character  
Search for the letter “D” in bar codes and send all the data that follows, including the “D.” Using the bar code above:  
Command string: F844F10D  
F8 is the “Search forward for a character” command  
44 is the hex value for “D”  
F1 is the “Send all characters” command  
0D is the hex value for a CR  
The data is output as:  
DEFGHIJ  
<CR>  
Search backward for a character  
F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to  
the “xx” character. Syntax = F9xx where xx stands for the search character’s hex value for its ASCII code.  
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.  
Search forward for a string  
B0 Search forward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B0nnnnS  
where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string.  
For example, B0000454657374 will search forward for the first occurrence of the 4 character string “Test.”  
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.  
B0 Example: Send bar code data that starts after a string of characters  
Search for the letters “FGH” in bar codes and send all the data that follows, including “FGH.” Using the bar code  
above:  
Command string: B00003464748F10D  
B0 is the “Search forward for a string” command  
0003 is the string length (3 characters)  
46 is the hex value for “F”  
47 is the hex value for “G”  
48 is the hex value for “H”  
F1 is the “Send all characters” command  
0D is the hex value for a CR  
The data is output as:  
FGHIJ  
<CR>  
Search backward for a string  
B1 Search backward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B1nnnnS  
where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string.  
For example, B1000454657374 will search backward for the first occurrence of the 4 character string “Test.”  
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.  
5 - 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Search forward for a non-matching character  
E6 Search the input message forward for the first non-“xx” character from the current cursor position, leaving the cursor  
pointing to the non-“xx” character. Syntax = E6xx where xx stands for the search character’s hex value for its ASCII  
code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character  
codes.  
E6 Example: Remove zeroes at the beginning of bar code data  
This example shows a bar code that has been zero filled. You may want to ignore the zeroes and send all the data that  
follows. E6 searches forward for the first character that is not zero, then sends all the data after, followed by a carriage  
return. Using the bar code above:  
Command string: E630F10D  
E6 is the “Search forward for a non-matching character” command  
30 is the hex value for 0  
F1 is the “Send all characters” command  
0D is the hex value for a CR  
The data is output as:  
37692  
<CR>  
Search backward for a non-matching character  
E7 Search the input message backward for the first non-“xx” character from the current cursor position, leaving the cursor  
pointing to the non-“xx” character. Syntax = E7xx where xx stands for the search character’s hex value for its ASCII  
code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character  
codes.  
Miscellaneous Commands  
Suppress characters  
FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is  
advanced by other commands. When the FC command is encountered, the suppress function is terminated. The  
cursor is not moved by the FB command.  
Syntax = FBnnxxyy . .zz where nn is a count of the number of suppressed characters in the list, and xxyy .. zz is the list  
of characters to be suppressed.  
FB Example: Remove spaces in bar code data  
This example shows a bar code that has spaces in the data. You may want to remove the spaces before sending the  
data. Using the bar code above:  
Command string: FB0120F10D  
FB is the “Suppress characters” command  
01 is the number of character types to be suppressed  
20 is the hex value for a space  
F1 is the “Send all characters” command  
0D is the hex value for a CR  
The data is output as:  
34567890  
<CR>  
5 - 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Stop suppressing characters  
FC Disables suppress filter and clear all suppressed characters. Syntax = FC.  
Replace characters  
E4 Replaces up to 15 characters in the output message, without moving the cursor. Replacement continues until the E5  
command is encountered. Syntax = E4nnxx xx yy yy ...zz zz where nn is the total count of the number of characters  
1
2
1
2
1
2
in the list (characters to be replaced plus replacement characters); xx defines characters to be replaced and xx defines  
1
2
replacement characters, continuing through zz and zz .  
1
2
E4 Example: Replace zeroes with CRs in bar code data  
If the bar code has characters that the host application does not want included, you can use the E4 command to  
replace those characters with something else. In this example, you will replace the zeroes in the bar code above with  
carriage returns.  
Command string: E402300DF10D  
E4 is the “Replace characters” command  
02 is the total count of characters to be replaced, plus the replacement characters (0 is replaced by CR, so total char-  
acters = 2)  
30 is the hex value for 0  
0D is the hex value for a CR (the character that will replace the 0)  
F1 is the “Send all characters” command  
0D is the hex value for a CR  
The data is output as:  
1234  
5678  
ABC  
<CR>  
Stop replacing characters  
E5 Terminates character replacement. Syntax = E5.  
Compare characters  
FE Compare the character in the current cursor position to the character “xx.” If characters are equal, move the cursor  
forward one position. Syntax = FExx where xx stands for the comparison character’s hex value for its ASCII code.  
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.  
Compare string  
B2 Compare the string in the input message to the string “s.” If the strings are equal, move the cursor forward past the end  
of the string. Syntax = B2nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value  
of each character in the match string. For example, B2000454657374 will compare the string at the current cursor  
position with the 4 character string “Test.”  
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.  
Check for a number  
EC Check to make sure there is an ASCII number at the current cursor position. The format is aborted if the character is  
not numeric.  
EC Example: Only output the data if the bar code begins with a number  
If you want only data from bar codes that begin with a number, you can use EC to check for the number.  
Command string: ECF10D  
EC is the “Check for a number” command  
F1 is the “Send all characters” command  
0D is the hex value for a CR  
5 - 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If this bar code is read,  
the next data format, if there is one, will be used on the data. If there  
is no other format, the format fails and the raw data is output as AB1234.  
If this bar code is read:  
the data is output as:  
1234AB  
<CR>  
Check for non-numeric character  
ED Check to make sure there is a non-numeric ASCII character at the current cursor position. The format is aborted if the  
character is numeric.  
ED Example: Only output the data if the bar code begins with a letter  
If you want only data from bar codes that begin with a letter, you can use ED to check for the letter.  
Command string: EDF10D  
ED is the “Check for a non-numeric character” command  
F1 is the “Send all characters” command  
0D is the hex value for a CR  
If this bar code is read,  
the next data format, if there is one, will be used on this data. If there  
is no other format, the format fails and the raw data is output as 1234AB.  
If this bar code is read:  
the data is output as:  
AB1234  
<CR>  
Insert a delay  
EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position. Syntax = EFnnnn  
where nnnn stands for the delay in 5ms increments, up to 9999. This command can only be used with keyboard  
emulation.a  
Discard Data  
B8 Discards types of data. For example, you may want to discard Code 128 bar codes that begin with the letter A. In step  
4 (page 5-1), select 6A (for Code 128), and in step 5, select 9999 (for all lengths). Enter FE41B8 to compare and discard  
Code 128 bar codes that begin with the letter A. Syntax = B8.  
Note: The B8 command must be entered after all other commands.  
The Data Format must be Required (see page 5-12) in order for the B8 command to work.  
If Data Format is On, but Not Required (page 5-12), bar code data that meets the B8 format is scanned and output  
as usual.  
Because the data format needs to be On and Required (page 5-12) for the B8 command, you must input data formats  
for all bar codes you wish to discard as well as all bar codes you wish to output.  
Other data format settings impact the B8 command. If Data Format Non-Match Error Tone is On (page 5-13), the  
scan engine emits an error tone. If Data format Non-Match Error Tone is Off, the code is disabled for reading and  
no tone is sounded.  
5 - 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Data Formatter  
When Data Formatter is turned Off, the bar code data is output to the host as read, including prefixes and suffixes.  
Data Formatter Off  
You may wish to require the data to conform to a data format you have created and saved. The following settings can be applied  
to your data format:  
Data Formatter On, Not Required, Keep Prefix/Suffix  
Scanned data is modified according to your data format, and prefixes and suffixes are transmitted.  
Data Formatter On, Not Required, Drop Prefix/Suffix  
Scanned data is modified according to your data format. If a data format is found for a particular symbol, those prefixes and  
suffixes are not transmitted. If a data format is not found for that symbol, the prefixes and suffixes are transmitted.  
Data Format Required, Keep Prefix/Suffix  
Scanned data is modified according to your data format, and prefixes and suffixes are transmitted. Any data that does not  
match your data format requirements generates an error tone and the data in that bar code is not transmitted. If you wish  
to process this type of bar code without generating an error tone, see Data Format Non-Match Error Tone.  
Data Format Required, Drop Prefix/Suffix  
Scanned data is modified according to your data format. If a data format is found for a particular symbol, those prefixes and  
suffixes are not transmitted. Any data that does not match your data format requirements generates an error tone. If you  
wish to process this type of bar code without generating an error tone, see Data Format Non-Match Error Tone.  
Choose one of the following options. Default = Data Formatter On, Not Required, Keep Prefix/Suffix.  
* Data Formatter On,  
Not Required,  
Keep Prefix/Suffix  
Data Formatter On,  
Not Required,  
Drop Prefix/Suffix  
Data Format Required,  
Keep Prefix/Suffix  
Data Format Required,  
Drop Prefix/Suffix  
5 - 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Data Format Non-Match Error Tone  
When a bar code is encountered that doesn’t match your required data format, the scan engine normally generates an error  
tone. However, you may want to continue scanning bar codes without hearing the error tone. If you scan the Data Format  
Non-Match Error Tone Off bar code, data that doesn’t conform to your data format is not transmitted, and no error tone will  
sound. If you wish to hear the error tone when a non-matching bar code is found, scan the Data Format Non-Match Error  
Tone On bar code. Default = Data Format Non-Match Error Tone On.  
* Data Format Non-Match Error  
Tone On  
Data Format Non-Match  
Error Tone Off  
Primary/Alternate Data Formats  
You can save up to four data formats, and switch between these formats. Your primary data format is saved under 0. Your other  
three formats are saved under 1, 2, and 3. To set your device to use one of these formats, scan one of the bar codes below.  
Primary Data Format  
Data Format 1  
Data Format 2  
Data Format 3  
Single Scan Data Format Change  
You can also switch between data formats for a single scan. The next bar code is scanned using an alternate data format,  
then reverts to the format you have selected above (either Primary, 1, 2, or 3).  
5 - 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
For example, you may have set your device to the data format you saved as Data Format 3. You can switch to Data Format  
1 for a single trigger pull by scanning the Single Scan-Data Format 1 bar code below. The next bar code that is scanned  
uses Data Format 1, then reverts back to Data Format 3.  
Single Scan-Primary  
Data Format  
Single Scan-Data Format 1  
Single Scan-Data Format 2  
Single Scan-Data Format 3  
5 - 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
6
Symbologies  
This programming section contains the following menu selections. Refer to Chapter 10 for settings and defaults.  
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
All Symbologies  
Aztec Code  
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Interleaved 2 of 5  
Korea Post  
China Post (Hong Kong 2 of 5)  
Chinese Sensible (Han Xin) Code  
Codabar  
Matrix 2 of 5  
MaxiCode  
MicroPDF417  
Codablock A  
MSI  
Codablock F  
NEC 2 of 5  
Code 11  
Postal Codes - 2D  
Code 128  
Postal Codes - Linear  
Code 32 Pharmaceutical (PARAF)  
Code 39  
PDF417  
GS1 DataBar Omnidirectional  
Code 93  
QR Code  
Data Matrix  
Straight 2 of 5 IATA (two-bar start/stop)  
EAN/JAN-13  
Straight 2 of 5 Industrial (three-bar start/stop)  
EAN/JAN-8  
TCIF Linked Code 39 (TLC39)  
GS1 Composite Codes  
GS1 DataBar Expanded  
GS1 DataBar Limited  
GS1 DataBar Omnidirectional  
GS1 Emulation  
Telepen  
Trioptic Code  
UPC-A  
UPC-A/EAN-13 with Extended Coupon Code  
UPC-E0  
UPC-E1  
GS1-128  
All Symbologies  
If you want to decode all the symbologies allowable for your scanner, scan the All Symbologies On code. If on the other hand,  
you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular sym-  
bology.  
All Symbologies On  
All Symbologies Off  
Note: When All Symbologies On is scanned, 2D Postal Codes are not enabled. 2D Postal Codes must be enabled separately.  
Message Length Description  
You are able to set the valid reading length of some of the bar code symbologies. If the data length of the scanned bar code  
doesn’t match the valid reading length, the scanner will issue an error tone. You may wish to set the same value for minimum  
and maximum length to force the scanner to read fixed length bar code data. This helps reduce the chances of a misread.  
EXAMPLE: Decode only those bar codes with a count of 9-20 characters.  
Min. length = 09Max. length = 20  
6 - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
EXAMPLE: Decode only those bar codes with a count of 15 characters.  
Min. length = 15Max. length = 15  
For a value other than the minimum and maximum message length defaults, scan the bar codes included in the explanation of  
the symbology, then scan the digit value of the message length and Save bar codes on the Programming Chart inside the back  
cover of this manual. The minimum and maximum lengths and the defaults are included with the respective symbologies.  
Codabar  
<Default All Codabar Settings>  
Codabar On/Off  
* On  
Off  
Codabar Start/Stop Characters  
Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/  
Stop characters. Default = Don’t Transmit.  
Transmit  
* Don’t Transmit  
Codabar Check Character  
Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar bar  
codes with Modulo 16 check characters. Default = No Check Character.  
No Check Character indicates that the scanner reads and transmits bar code data with or without a check character.  
When Check Character is set to Validate and Transmit, the scanner will only read Codabar bar codes printed with a check  
character, and will transmit this character at the end of the scanned data.  
When Check Character is set to Validate, but Don’t Transmit, the unit will only read Codabar bar codes printed with a  
check character, but will not transmit the check character with the scanned data.  
* No Check Character  
6 - 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Validate Modulo 16, but  
Don’t Transmit  
Validate Modulo 16  
and Transmit  
Codabar Concatenation  
Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having  
a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concatenated  
into one with the “D” characters omitted.  
A 1 2 3 4 D D 5 6 7 8 A  
Select Require to prevent the scanner from decoding a single “D” Codabar symbol without its companion. This selection  
has no effect on Codabar symbols without Stop/Start D characters.  
On  
* Off  
Require  
Codabar Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60.  
Minimum Message Length  
Maximum Message Length  
6 - 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Code 39  
< Default All Code 39 Settings >  
Code 39 On/Off  
* On  
Off  
Code 39 Start/Stop Characters  
Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/  
Stop characters. Default = Don’t Transmit.  
Transmit  
* Don’t Transmit  
Code 39 Check Character  
No Check Character indicates that the scanner reads and transmits bar code data with or without a check character.  
When Check Character is set to Validate, but Don’t Transmit, the unit only reads Code 39 bar codes printed with a check  
character, but will not transmit the check character with the scanned data.  
When Check Character is set to Validate and Transmit, the scanner only reads Code 39 bar codes printed with a check  
character, and will transmit this character at the end of the scanned data. Default = No Check Character.  
* No Check Character  
Validate, but Don’t Transmit  
Validate and Transmit  
6 - 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Code 39 Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 48.  
Minimum Message Length  
Maximum Message Length  
Code 39 Append  
This function allows the scanner to append the data from several Code 39 bar codes together before transmitting them to  
the host computer. When the scanner encounters a Code 39 bar code with the append trigger character(s), it buffers Code  
39 bar codes until it reads a Code 39 bar code that does not have the append trigger. The data is then transmitted in the  
order in which the bar codes were read (FIFO). Default = Off.  
On  
* Off  
Code 32 Pharmaceutical (PARAF)  
Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian pharmacies. This symbology is also known as  
PARAF.  
Note: Trioptic Code (page 6-32) must be turned off while scanning Code 32 Pharmaceutical codes.  
On  
* Off  
6 - 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Full ASCII  
If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single  
character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #.  
Default = Off.  
NUL %U  
SOH $A  
STX $B  
ETX $C  
EOT $D  
ENQ $E  
ACK $F  
BEL $G  
BS $H  
HT $I  
DLE $P  
DC1 $Q  
DC2 $R  
DC3 $S  
DC4 $T  
NAK $U  
SYN $V  
ETB $W  
CAN $X  
EM $Y  
SUB $Z  
ESC %A  
FS %B  
GS %C  
RS %D  
US %E  
SP  
!
SPACE  
/A  
/B  
/C  
/D  
/E  
/F  
/G  
/H  
/I  
0
1
2
3
4
5
6
7
8
9
:
0
@
A
B
C
D
E
F
%V  
A
B
C
D
E
F
P
Q
R
S
T
U
V
W
X
Y
Z
[
P
‘
%W  
+A  
+B  
+C  
+D  
+E  
+F  
+G  
+H  
+I  
p
q
r
+P  
+Q  
+R  
+S  
+T  
1
Q
a
b
c
d
e
f
“
2
R
#
$
%
&
‘
3
S
s
t
4
T
5
U
u
v
w
x
y
z
{
+U  
+V  
+W  
+X  
+Y  
+Z  
6
V
7
G
H
I
G
H
I
W
X
g
h
i
(
8
)
9
Y
LF $J  
VT $K  
FF $L  
CR $M  
SO $N  
*
/J  
/Z  
%F  
%G  
%H  
%I  
%J  
J
J
Z
j
+J  
+
,
/K  
/L  
;
K
L
K
L
%K  
%L  
%M  
%N  
%O  
k
l
+K  
+L  
%P  
%Q  
%R  
%S  
<
=
>
?
\
|
-
-
M
N
O
M
N
O
]
m
n
o
+M  
+N  
}
.
.
^
~
SI  
$O  
/
/O  
_
+O DEL %T  
Character pairs /M and /N decode as a minus sign and period respectively.  
Character pairs /P through /Y decode as 0 through 9.  
Full ASCII On  
* Full ASCII Off  
Code 39 Code Page  
Code pages define the mapping of character codes to characters. If the data received does not display with the proper  
characters, it may be because the bar code being scanned was created using a code page that is different from the one the  
host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were  
created (see ISO 2022/ISO 646 Character Replacements on page A-8), and scan the value and the Save bar code from  
the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly.  
Code 39 Code Page  
6 - 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Interleaved 2 of 5  
< Default All Interleaved 2 of 5 Settings >  
Interleaved 2 of 5 On/Off  
* On  
Off  
Check Digit  
No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit.  
When Check Digit is set to Validate, but Don’t Transmit, the unit only reads Interleaved 2 of 5 bar codes printed with a  
check digit, but will not transmit the check digit with the scanned data.  
When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 bar codes printed with a  
check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit.  
* No Check Digit  
Validate, but Don’t Transmit  
Validate and Transmit  
Interleaved 2 of 5 Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.  
Minimum Message Length  
6 - 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Maximum Message Length  
NEC 2 of 5  
< Default All NEC 2 of 5 Settings >  
NEC 2 of 5 On/Off  
* On  
Off  
Check Digit  
No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit.  
When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 bar codes printed with a check  
digit, but will not transmit the check digit with the scanned data.  
When Check Digit is set to Validate and Transmit, the scanner only reads NEC 2 of 5 bar codes printed with a check digit,  
and will transmit this digit at the end of the scanned data. Default = No Check Digit.  
* No Check Digit  
Validate, but Don’t Transmit  
Validate and Transmit  
6 - 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
NEC 2 of 5 Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.  
Minimum Message Length  
Maximum Message Length  
Code 93  
< Default All Code 93 Settings >  
Code 93 On/Off  
* On  
Off  
Code 93 Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.  
Minimum Message Length  
Maximum Message Length  
6 - 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Code 93 Append  
This function allows the scanner to append the data from several Code 93 bar codes together before transmitting them to  
the host computer. When this function is enabled, the scanner stores those Code 93 bar codes that start with a space  
(excluding the start and stop symbols), and does not immediately transmit the data. The scanner stores the data in the  
order in which the bar codes are read, deleting the first space from each. The scanner transmits the appended data when  
it reads a Code 93 bar code that starts with a character other than a space. Default = Off.  
On  
* Off  
Code 93 Code Page  
Code pages define the mapping of character codes to characters. If the data received does not display with the proper  
characters, it may be because the bar code being scanned was created using a code page that is different from the one the  
host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were  
created (see ISO 2022/ISO 646 Character Replacements on page A-8), and scan the value and the Save bar code from  
the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly.  
Code 93 Code Page  
6 - 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Straight 2 of 5 Industrial (three-bar start/stop)  
<Default All Straight 2 of 5 Industrial Settings>  
Straight 2 of 5 Industrial On/Off  
On  
* Off  
Straight 2 of 5 Industrial Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.  
Minimum Message Length  
Maximum Message Length  
6 - 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Straight 2 of 5 IATA (two-bar start/stop)  
<Default All Straight 2 of 5 IATA Settings>  
Straight 2 of 5 IATA On/Off  
On  
* Off  
Straight 2 of 5 IATA Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.  
Minimum Message Length  
Maximum Message Length  
6 - 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Matrix 2 of 5  
<Default All Matrix 2 of 5 Settings>  
Matrix 2 of 5 On/Off  
On  
* Off  
Matrix 2 of 5 Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.  
Minimum Message Length  
Maximum Message Length  
6 - 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Code 11  
<Default All Code 11 Settings>  
Code 11 On/Off  
On  
* Off  
Check Digits Required  
This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits.  
One Check Digit  
* Two Check Digits  
Code 11 Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.  
Minimum Message Length  
Maximum Message Length  
6 - 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Code 128  
<Default All Code 128 Settings>  
Code 128 On/Off  
* On  
Off  
ISBT 128 Concatenation  
In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard for communicating critical blood informa-  
tion in a uniform manner. The use of ISBT formats requires a paid license. The ISBT 128 Application Specification  
describes 1) the critical data elements for labeling blood products, 2) the current recommendation to use Code 128 due to  
its high degree of security and its space-efficient design, 3) a variation of Code 128 that supports concatenation of neigh-  
boring symbols, and 4) the standard layout for bar codes on a blood product label. Use the bar codes below to turn concat-  
enation on or off. Default =Off.  
On  
* Off  
Code 128 Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.  
Minimum Message Length  
Maximum Message Length  
6 - 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Code 128 Append  
This function allows the scanner to append the data from several Code 128 bar codes together before transmitting them to  
the host computer. When the scanner encounters a Code 128 bar code with the append trigger character(s), it buffers  
Code 128 bar codes until it reads a Code 128 bar code that does not have the append trigger. The data is then transmitted  
in the order in which the bar codes were read (FIFO). Default = On.  
* On  
Off  
Code 128 Code Page  
Code pages define the mapping of character codes to characters. If the data received does not display with the proper  
characters, it may be because the bar code being scanned was created using a code page that is different from the one the  
host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were  
created (see ISO 2022/ISO 646 Character Replacements on page A-8), and scan the value and the Save bar code from  
the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly.  
Code 128 Code Page  
6 - 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
GS1-128  
<Default All GS1-128 Settings>  
GS1-128 On/Off  
* On  
Off  
GS1-128 Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-80. Minimum Default = 1, Maximum Default = 80.  
Minimum Message Length  
Maximum Message Length  
6 - 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Telepen  
<Default All Telepen Settings>  
Telepen On/Off  
On  
* Off  
Telepen Output  
Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII  
(start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and  
decodes them as compressed numeric with optional full ASCII (start/stop pattern 2). Default = AIM Telepen Output.  
* AIM Telepen Output  
Original Telepen Output  
Telepen Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-60. Minimum Default = 1, Maximum Default = 60.  
Minimum Message Length  
Maximum Message Length  
6 - 18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
UPC-A  
<Default All UPC-A Settings>  
UPC-A On/Off  
* On  
Off  
Note: To convert UPC-A bar codes to EAN-13, see Convert UPC-A to EAN-13 on page 6-24.  
UPC-A Check Digit  
This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.  
Default = On.  
* On  
Off  
UPC-A Number System  
The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can  
be programmed so it will not transmit it. Default = On.  
* On  
Off  
6 - 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
UPC-A Addenda  
This selection adds 2 or 5 digits to the end of all scanned UPC-A data.  
Default = Off for both 2 Digit and 5 Digit Addenda.  
2 Digit Addenda On  
* 2 Digit Addenda Off  
5 Digit Addenda On  
* 5 Digit Addenda Off  
UPC-A Addenda Required  
When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or  
5 digit addenda listed on page 6-20. Default = Not Required.  
Required  
* Not Required  
UPC-A Addenda Separator  
When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned  
off, there is no space. Default = On.  
* On  
Off  
6 - 20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
UPC-A/EAN-13  
with Extended Coupon Code  
Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. When left on the default setting  
(Off), the scanner treats Coupon Codes and Extended Coupon Codes as single bar codes.  
If you scan the Allow Concatenation code, when the scanner sees the coupon code and the extended coupon code in a single  
scan, it transmits both as separate symbologies. Otherwise, it transmits the first coupon code it reads.  
If you scan the Require Concatenation code, the scanner must see and read the coupon code and extended coupon code in a  
single read to transmit the data. No data is output unless both codes are read. Default = Off.  
* Off  
Allow Concatenation  
Require Concatenation  
Coupon GS1 DataBar Output  
If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to scan and output only the data from the GS1  
DataBar code. Scan the GS1 Output On code below to scan and output only the GS1 DataBar code data. Default = GS1 Out-  
put Off.  
* GS1 Output Off  
GS1 Output On  
6 - 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
UPC-E0  
<Default All UPC-E Settings>  
UPC-E0 On/Off  
Most U.P.C. bar codes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to  
read codes that lead with the 1 number system, use UPC-E1 (page 6-24). Default = On.  
* UPC-E0 On  
UPC-E0 Off  
UPC-E0 Expand  
UPC-E Expand expands the UPC-E code to the 12 digit, UPC-A format. Default = Off.  
On  
* Off  
UPC-E0 Addenda Required  
When Required is scanned, the scanner will only read UPC-E bar codes that have addenda. Default = Not Required.  
Required  
* Not Required  
6 - 22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
UPC-E0 Addenda Separator  
When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned  
Off, there is no space. Default = On.  
* On  
Off  
UPC-E0 Check Digit  
Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = On.  
* On  
Off  
UPC-E0 Leading Zero  
This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan  
Off. Default = On.  
* On  
Off  
UPC-E0 Addenda  
This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda.  
2 Digit Addenda On  
* 2 Digit Addenda Off  
6 - 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
5 Digit Addenda On  
* 5 Digit Addenda Off  
UPC-E1  
Most U.P.C. bar codes lead with the 0 number system. For these codes, use UPC-E0 (page 6-22). If you need to read codes  
that lead with the 1 number system, use the UPC-E1 On selection. Default = Off.  
UPC-E1 On  
* UPC-E1 Off  
EAN/JAN-13  
<Default All EAN/JAN Settings>  
EAN/JAN-13 On/Off  
* On  
Off  
Convert UPC-A to EAN-13  
When UPC-A Converted to EAN-13 is selected, UPC-A bar codes are converted to 13 digit EAN-13 codes by adding a  
zero to the front. When Do not Convert UPC-A is selected, UPC-A codes are read as UPC-A.  
UPC-A Converted to EAN-13  
6 - 24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
* Do not Convert UPC-A  
EAN/JAN-13 Check Digit  
This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.  
Default = On.  
* On  
Off  
EAN/JAN-13 Addenda  
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit  
Addenda.  
2 Digit Addenda On  
* 2 Digit Addenda Off  
5 Digit Addenda On  
* 5 Digit Addenda Off  
EAN/JAN-13 Addenda Required  
When Required is scanned, the scanner will only read EAN/JAN-13 bar codes that have addenda. Default = Not Required.  
Required  
6 - 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
* Not Required  
EAN/JAN-13 Addenda Separator  
When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned  
Off, there is no space. Default = On.  
* On  
Off  
Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon  
Code (page 6-21).  
ISBN Translate  
When On is scanned, EAN-13 Bookland symbols are translated into their equivalent ISBN number format. Default = Off.  
On  
* Off  
6 - 26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
EAN/JAN-8  
<Default All EAN/JAN-8 Settings>  
EAN/JAN-8 On/Off  
* On  
Off  
EAN/JAN-8 Check Digit  
This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.  
Default = On.  
* On  
Off  
EAN/JAN-8 Addenda  
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit  
Addenda.  
2 Digit Addenda On  
* 2 Digit Addenda Off  
5 Digit Addenda On  
6 - 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
* 5 Digit Addenda Off  
EAN/JAN-8 Addenda Required  
When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that have addenda. Default = Not Required.  
Required  
* Not Required  
EAN/JAN-8 Addenda Separator  
When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned  
Off, there is no space. Default = On.  
* On  
Off  
6 - 28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
MSI  
<Default All MSI Settings>  
MSI On/Off  
On  
* Off  
MSI Check Character  
Different types of check characters are used with MSI bar codes. You can program the scanner to read MSI bar codes with  
Type 10 check characters. Default = Validate Type 10, but Don’t Transmit.  
When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI bar codes printed with  
the specified type check character(s), and will transmit the character(s) at the end of the scanned data.  
When Check Character is set to Validate Type 10/11, but Don’t Transmit, the unit will only read MSI bar codes printed  
with the specified type check character(s), but will not transmit the check character(s) with the scanned data.  
* Validate Type 10, but Don’t  
Transmit  
Validate Type 10 and Transmit  
Validate 2 Type 10 Characters,  
but Don’t Transmit  
Validate 2 Type 10 Characters  
and Transmit  
Validate Type 10 then Type 11  
Character, but Don’t Transmit  
6 - 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Validate Type 10 then  
Type 11 Character and Transmit  
Disable MSI Check Characters  
MSI Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48.  
Minimum Message Length  
Maximum Message Length  
6 - 30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
GS1 DataBar Omnidirectional  
< Default All GS1 DataBar Omnidirectional Settings >  
GS1 DataBar Omnidirectional On/Off  
* On  
Off  
GS1 DataBar Limited  
< Default All GS1 DataBar Limited Settings >  
GS1 DataBar Limited On/Off  
* On  
Off  
6 - 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
GS1 DataBar Expanded  
< Default All GS1 DataBar Expanded Settings >  
GS1 DataBar Expanded On/Off  
* On  
Off  
GS1 DataBar Expanded Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74.  
Minimum Message Length  
Maximum Message Length  
Trioptic Code  
Note: If you are going to scan Code 32 Pharmaceutical codes (page 6-5), Trioptic Code must be off.  
Trioptic Code is used for labeling magnetic storage media.  
On  
* Off  
6 - 32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Codablock A  
<Default All Codablock A Settings>  
Codablock A On/Off  
On  
* Off  
Codablock A Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-600. Minimum Default = 1, Maximum Default = 600.  
Minimum Message Length  
Maximum Message Length  
6 - 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Codablock F  
<Default All Codablock F Settings>  
Codablock F On/Off  
On  
* Off  
Codablock F Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048.  
Minimum Message Length  
Maximum Message Length  
6 - 34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
PDF417  
< Default All PDF417 Settings >  
PDF417 On/Off  
* On  
Off  
PDF417 Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750.  
Minimum Message Length  
Maximum Message Length  
MacroPDF417  
MacroPDF417 is an implementation of PDF417 capable of encoding very large amounts of data into multiple PDF417 bar  
codes. When this selection is enabled, these multiple bar codes are assembled into a single data string. Default = On.  
* On  
Off  
6 - 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
MicroPDF417  
< Default All MicroPDF417 Settings >  
MicroPDF417 On/Off  
On  
* Off  
MicroPDF417 Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-366. Minimum Default = 1, Maximum Default = 366.  
Minimum Message Length  
Maximum Message Length  
GS1 Composite Codes  
Linear codes are combined with a unique 2D composite component to form a new class called GS1 Composite symbology.  
GS1 Composite symbologies allow for the co-existence of symbologies already in use. Default = Off.  
On  
* Off  
6 - 36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
UPC/EAN Version  
Scan the UPC/EAN Version On bar code to decode GS1 Composite symbols that have a U.P.C. or an EAN linear compo-  
nent. (This does not affect GS1 Composite symbols with a GS1-128 or GS1 linear component.) Default = UPC/EAN Ver-  
sion Off.  
UPC/EAN Version On  
* UPC/EAN Version Off  
Note: If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to scan and output only the data from  
the GS1 DataBar code. See Coupon GS1 DataBar Output (page 6-21) for further information.  
GS1 Composite Code Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-2435. Minimum Default = 1, Maximum Default = 2435.  
Minimum Message Length  
Maximum Message Length  
GS1 Emulation  
The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent  
GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1-128, and  
GS1-128 DataBar and GS1 Composites. (Any application that accepts GS1 data can be simplified since it only needs to recog-  
nize one data carrier type.)  
If GS1-128 Emulation is scanned, all retail codes (U.P.C., UPC-E, EAN8, EAN13) are expanded out to 16 digits. If the AIM ID  
is enabled, the value will be the GS1-128 AIM ID, ]C1 (see Symbology Charts on page A-1).  
If GS1 DataBar Emulation is scanned, all retail codes (U.P.C., UPC-E, EAN8, EAN13) are expanded out to 16 digits. If the AIM  
ID is enabled, the value will be the GS1-DataBar AIM ID, ]em (see Symbology Charts on page A-1).  
If GS1 Code Expansion Off is scanned, retail code expansion is disabled, and UPC-E expansion is controlled by the UPC-E0  
Expand (page 6-22) setting. If the AIM ID is enabled, the value will be the GS1-128 AIM ID, ]C1 (see Symbology Charts on  
page A-1).  
If EAN8 to EAN13 Conversion is scanned, all EAN8 bar codes are converted to EAN13 format.  
Default = GS1 Emulation Off.  
GS1-128 Emulation  
6 - 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
GS1 DataBar Emulation  
GS1 Code Expansion Off  
EAN8 to EAN13 Conversion  
* GS1 Emulation Off  
TCIF Linked Code 39 (TLC39)  
This code is a composite code since it has a Code 39 linear component and a MicroPDF417 stacked code component. All bar  
code readers are capable of reading the Code 39 linear component. The MicroPDF417 component can only be decoded if  
TLC39 On is selected. The linear component may be decoded as Code 39 even if TLC39 is off. Default = Off.  
On  
* Off  
QR Code  
< Default All QR Code Settings >  
QR Code On/Off  
This selection applies to both QR Code and Micro QR Code.  
* On  
Off  
6 - 38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
QR Code Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-7089. Minimum Default = 1, Maximum Default = 7089.  
Minimum Message Length  
Maximum Message Length  
QR Code Append  
This function allows the scanner to append the data from several QR Code bar codes together before transmitting them to  
the host computer. When the scanner encounters an QR Code bar code with the append trigger character(s), it buffers the  
number of QR Code bar codes determined by information encoded in those bar codes. Once the proper number of codes  
is reached, the data is output in the order specified in the bar codes. Default = On.  
* On  
Off  
QR Code Page  
QR Code pages define the mapping of character codes to characters. If the data received does not display with the proper  
characters, it may be because the bar code being scanned was created using a code page that is different from the one the  
host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were  
created (see ISO 2022/ISO 646 Character Replacements on page A-8), and scan the value and the Save bar code from  
the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly.  
QR Code Page  
6 - 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Data Matrix  
< Default All Data Matrix Settings >  
Data Matrix On/Off  
* On  
Off  
Data Matrix Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-3116. Minimum Default = 1, Maximum Default = 3116.  
Minimum Message Length  
Maximum Message Length  
Data Matrix Append  
This function allows the scanner to append the data from several Data Matrix bar codes together before transmitting them  
to the host computer. When the scanner encounters an Data Matrix bar code with the append trigger character(s), it buf-  
fers the number of Data Matrix bar codes determined by information encoded in those bar codes. Once the proper number  
of codes is reached, the data is output in the order specified in the bar codes. Default = On.  
* On  
Off  
Data Matrix Code Page  
Data Matrix Code pages define the mapping of character codes to characters. If the data received does not display with the  
proper characters, it may be because the bar code being scanned was created using a code page that is different from the  
one the host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar  
6 - 40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
codes were created (see ISO 2022/ISO 646 Character Replacements on page A-8), and scan the value and the Save bar  
code from the Programming Chart on the inside the back cover of this manual. The data characters should then appear  
properly.  
Data Matrix Code Page  
MaxiCode  
< Default All MaxiCode Settings >  
MaxiCode On/Off  
On  
* Off  
MaxiCode Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-150. Minimum Default = 1, Maximum Default = 150.  
Minimum Message Length  
Maximum Message Length  
6 - 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Aztec Code  
< Default All Aztec Code Settings >  
Aztec Code On/Off  
* On  
Off  
Aztec Code Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-3832. Minimum Default = 1, Maximum Default = 3832.  
Minimum Message Length  
Maximum Message Length  
Aztec Append  
This function allows the scanner to append the data from several Aztec bar codes together before transmitting them to the  
host computer. When the scanner encounters an Aztec bar code with the append trigger character(s), it buffers the number  
of Aztec bar codes determined by information encoded in those bar codes. Once the proper number of codes is reached,  
the data is output in the order specified in the bar codes. Default = On.  
* On  
Off  
Aztec Code Page  
Aztec Code pages define the mapping of character codes to characters. If the data received does not display with the  
proper characters, it may be because the bar code being scanned was created using a code page that is different from the  
one the host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar  
6 - 42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
codes were created (see ISO 2022/ISO 646 Character Replacements on page A-8), and scan the value and the Save bar  
code from the Programming Chart on the inside the back cover of this manual. The data characters should then appear  
properly.  
Aztec Code Page  
Chinese Sensible (Han Xin) Code  
< Default All Han Xin Settings >  
Han Xin Code On/Off  
On  
* Off  
Han Xin Code Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional  
information. Minimum and Maximum lengths = 1-7833. Minimum Default = 1, Maximum Default = 7833.  
Minimum Message Length  
Maximum Message Length  
6 - 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Postal Codes - 2D  
The following lists the possible 2D postal codes, and 2D postal code combinations that are allowed. Only one 2D postal code  
selection can be active at a time. If you scan a second 2D postal code selection, the first selection is overwritten. Default = 2D  
Postal Codes Off.  
* 2D Postal Codes Off  
Single 2D Postal Codes:  
Australian Post On  
British Post On  
Canadian Post On  
Intelligent Mail Bar Code On  
Japanese Post On  
KIX Post On  
Planet Code On  
Also see Planet Code  
Check Digit, page 6-47.  
Postal-4i On  
6 - 44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Postnet On  
Also see Postnet Check  
Digit, page 6-47.  
Postnet with B and B’ Fields On  
InfoMail On  
Combination 2D Postal Codes:  
InfoMail and British  
Post On  
Intelligent Mail Bar Code and  
Postnet with B and B’ Fields On  
Postnet and  
Postal-4i On  
Postnet and  
Intelligent Mail Bar Code On  
Postal-4i and  
Intelligent Mail Bar Code On  
Postal-4i and  
Postnet with B and B’ Fields On  
Planet Code and  
Postnet On  
6 - 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Planet Code and  
Postnet with B and B’ Fields On  
Planet Code and  
Postal-4i On  
Planet Code and  
Intelligent Mail Bar Code On  
Planet Code,  
Postnet, and  
Postal-4i On  
Planet Code,  
Postnet, and  
Intelligent Mail Bar Code On  
Planet Code,  
Postal-4i, and  
Intelligent Mail Bar Code On  
Postnet,  
Postal-4i, and  
Intelligent Mail Bar Code On  
Planet Code,  
Postal-4i, and  
Postnet with B and B’ Fields On  
Planet Code,  
Intelligent Mail Bar Code, and  
Postnet with B and B’ Fields On  
Postal-4i,  
Intelligent Mail Bar Code, and  
Postnet with B and B’ Fields On  
6 - 46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Planet Code,  
Postal-4i,  
Intelligent Mail Bar Code, and  
Postnet On  
Planet Code,  
Postal-4i,  
Intelligent Mail Bar Code, and  
Postnet with B and B’ Fields On  
Planet Code Check Digit  
This selection allows you to specify whether the check digit should be transmitted at the end of Planet Code data. Default  
= Don’t Transmit.  
Transmit Check Digit  
* Don’t Transmit Check Digit  
Postnet Check Digit  
This selection allows you to specify whether the check digit should be transmitted at the end of Postnet data. Default =  
Don’t Transmit.  
Transmit Check Digit  
* Don’t Transmit Check Digit  
Australian Post Interpretation  
This option controls what interpretation is applied to customer fields in Australian 4-State symbols.  
Bar Output lists the bar patterns in “0123” format.  
Numeric N Table causes that field to be interpreted as numeric data using the N Table.  
Alphanumeric C Table causes the field to be interpreted as alphanumeric data using the C Table. Refer to the Australian  
Post Specification Tables.  
6 - 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Combination C and N Tables causes the field to be interpreted using either the C or N Tables.  
* Bar Output  
Numeric N Table  
Alphanumeric C Table  
Combination C and N Tables  
Postal Codes - Linear  
The following lists linear postal codes. Any combination of linear postal code selections can be active at a time.  
China Post (Hong Kong 2 of 5)  
<Default All China Post (Hong Kong 2 of 5) Settings>  
China Post (Hong Kong 2 of 5) On/Off  
On  
* Off  
China Post (Hong Kong 2 of 5) Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for addi-  
tional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.  
Minimum Message Length  
6 - 48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Maximum Message Length  
Korea Post  
Korea Post  
<Default All Korea Post Settings>  
On  
* Off  
Korea Post Message Length  
Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for addi-  
tional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48.  
Minimum Message Length  
Maximum Message Length  
Korea Post Check Digit  
This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data.  
Default = Don’t Transmit.  
Transmit Check Digit  
* Don’t Transmit Check Digit  
6 - 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
6 - 50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
Imaging Commands  
The scan engine is like a digital camera in the way it captures, manipulates, and transfers images. The following commands  
allow you to alter the way the scan engine performs these functions.  
Single-Use Basis  
Imaging Commands with their modifiers send instructions to the scan engine on a single-use basis, and take effect for a single  
image capture. Once that capture is complete, the scan engine reverts to its imaging default settings. If you want to perma-  
nently change a setting, you must use the serial default commands (see Chapter 10). When the serial default command is  
used, that selection becomes the new, permanent setting for the scan engine.  
Command Syntax  
Multiple modifiers and commands can be issued within one sequence. If additional modifiers are to be applied to the same  
command, just add the modifiers to that command. For example, to add 2 modifiers to the Image Snap command, such as set-  
ting the Imaging Style to 1P and the Wait for Trigger to 1T, you would enter IMGSNP1P1T.  
Note: After processing an image capture command (IMGSNP or IMGBOX), you must follow it with an IMGSHP command if you  
want to see it on your terminal.  
To add a command to a sequence, each new command is separated with a semicolon. For example, to add the Image Ship  
command to the above sequence, you would enter IMGSNP1P1T;IMGSHP.  
The imaging commands are:  
Image Snap - IMGSNP (page 7-1)  
Image Ship - IMGSHP (page 7-3)  
Intelligent Signature Capture - IMGBOX (page 7-10)  
The modifiers for each of these commands follow the command description.  
Note: The images included with each command description are examples only. The results you achieve may be different from  
those included in this manual. The quality of the output you receive will vary depending on lighting, quality of the initial  
image/object being captured, and distance of the scan engine from the image/object. To achieve a high quality image, it  
is recommended that you position your scan engine 4-6" (10.2-15.2 cm) away from the image/object you are capturing.  
Step 1 - Take a Picture Using IMGSNP  
Image Snap - IMGSNP  
An image is taken whenever the hardware button is pressed, or when the Image Snap (IMGSNP) command is processed.  
The image snap command has many different modifiers that can be used to change the look of the image in memory. Any num-  
ber of modifiers may be appended to the IMGSNP command. For example, you can use the following command to snap an  
image, increase the gain, and have the beeper sound once the snap is complete: IMGSNP2G1B  
IMGSNP Modifiers  
P - Imaging Style  
This sets the Image Snap style.  
0P Decoding Style. This processing allows a few frames to be taken until the exposure parameters are met. The last  
frame is then available for further use.  
1P Photo Style (default). This mimics a simple digital camera, and results in a visually optimized image.  
2P Manual Style. This is an advanced style that should only be used by an experienced user. It allows you the most  
freedom to set up the scan engine, and has no auto-exposure.  
B - Beeper  
Causes a beep to sound after an image is snapped.  
0B No beep (default)  
7 - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
1B Sounds a beep when the image is captured.  
T - Wait for Trigger  
Waits for a hardware button push before taking the image. This is only available when using Photo Style (1P).  
0T Takes image immediately (default)  
1T Waits for a button push, then takes the image  
L - LED State  
Determines if the LEDs should be on or off, and when. Ambient illumination (0L) is preferred for taking pictures of color  
documents, such as ID cards, especially when the scanner is in a stand. LED illumination (1L) is preferred when the scan-  
ner is handheld. LED State is not available when using Decoding Style (0P).  
0L LEDs off (default)  
1L LEDs on  
E - Exposure  
Exposure is used in Manual Style only (2P), and allows you to set the exposure time. This is similar to setting a shutter  
speed on a camera. The exposure time determines how long the scanner takes to record an image. On a bright day, expo-  
sure times can be very short because plenty of light is available to help record an image. At nighttime, exposure time can  
increase dramatically due to the near absence of light. Units are 127 microseconds. (Default = 7874)  
nE Range: 1 - 7874  
Example of Exposure at 7874E with  
fluorescent lighting:  
Example of Exposure at 100E with  
fluorescent lighting:  
G - Gain  
Gain is used in Manual Style only (2P). Like a volume control, the gain modifier boosts the signal and multiplies the pixel  
value. As you increase the gain, the noise in an image is also amplified.  
1G No gain (default)  
2G Medium gain  
4G Heavy gain  
8G Maximum gain  
Example of Gain at  
1G:  
Example of Gain at  
4G:  
Example of Gain at  
8G:  
7 - 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
W - Target White Value  
Sets the target for the median grayscale value in the captured image. For capturing close-up images of high contrast doc-  
uments, a lower setting, such as 75, is recommended. Higher settings result in longer exposure times and brighter images,  
but if the setting is too high, the image may be overexposed. Target White Value is only available when using Photo Style  
(1P). (Default = 125)  
nW Range: 0 - 255  
Example of White  
Value at 75W:  
Example of White  
Value at 125W:  
Example of White  
Value at 200W:  
D - Delta for Acceptance  
This sets the allowable range for the white value setting (see W - Target White Value). Delta is only available when using  
Photo Style (1P). (Default = 25)  
nD Range: 0 - 255  
U - Update Tries  
This sets the maximum number of frames the scan engine should take to reach the D - Delta for Acceptance. Update Tries  
is only available when using Photo Style (1P). (Default = 6)  
nU Range: 0 - 10  
% - Target Set Point Percentage  
Sets the target point for the light and dark values in the captured image. A setting of 75% means 75% of the pixels are at or  
below the target white value, and 25% of the pixels are above the target white value. Altering this setting from the default is  
not recommended under normal circumstances. To alter grayscale values, W - Target White Value should be used.  
(Default = 50)  
n% Range: 1 - 99  
Example of Target  
Set Point  
Percentage at 97%:  
Example of Target  
Set Point  
Percentage at 50%:  
Example of Target  
Set Point  
Percentage at 40%:  
Step 2 - Ship a Picture Using IMGSHP  
Image Ship - IMGSHP  
An image is taken whenever the button is pressed, or when the Image Snap (IMGSNP) command is processed. The last image  
is always stored in memory. You can “ship” the image by using the IMGSHP command.  
The image ship commands have many different modifiers that can be used to change the look of the image output. Modifiers  
affect the image that is transmitted, but do not affect the image in memory. Any number of modifiers may be appended to the  
IMGSHP command. For example, you can use the following command to snap and ship a bitmap image with gamma correction  
and document image filtering: IMGSNP;IMGSHP8F75K26U  
IMGSHP Modifiers  
A - Infinity Filter  
7 - 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Enhances pictures taken from very long distances (greater than 10 feet or 3m). The Infinity Filter should not be used with  
IMGSHP Modifiers (page 7-3).  
0A Infinity filter off (default)  
1A Infinity filter on  
Example of Infinity Filter off (0A)  
from approximately 12 feet  
(3.66m) away:  
Example of Infinity Filter on (1A)  
from approximately 12 feet (3.66m)  
away:  
C - Compensation  
Flattens the image to account for variations in illumination across the image.  
0C Compensation disabled (default)  
1C Compensation enabled  
Example of Compensation at 0C:  
Example of Compensation at 1C:  
D - Pixel Depth  
Indicates the number of bits per pixel in the transmitted image (KIM or BMP format only).  
8D 8 bits per pixel, grayscale image (default)  
1D 1 bit per pixel, black and white image  
7 - 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
E - Edge Sharpen  
An edge sharpen filter cleans up the edges of an image, making it look cleaner and sharper. While edge sharpening does  
make the image look cleaner, it also removes some fine detail from the original image. The strength of the edge sharpen  
filter can be entered from 1 to 24. Entering a 23E gives the sharpest edges, but also increases noise in the image.  
0E Don’t sharpen image (default)  
14E Apply edge sharpen for typical image  
ne Apply edge sharpen using strength n (n = 1-24)  
Example of Edge Sharpen at 0E:  
Example of Edge Sharpen at 24E:  
F - File Format  
Indicates the desired format for the image.  
0F KIM format  
1F TIFF binary  
2F TIFF binary group 4, compressed  
3F TIFF grayscale  
4F Uncompressed binary (upper left to lower right, 1 pixel/bit, 0 padded end of line)  
5F Uncompressed grayscale (upper left to lower right, bitmap format)  
6F JPEG image (default)  
8F BMP format (lower right to upper left, uncompressed)  
10F TIFF color compressed image  
11F TIFF color uncompressed image  
12F JPEG color image  
14F BMP color format  
15F BMP Uncompressed raw image  
H - Histogram Stretch  
Increases the contrast of the transmitted image. Not available with some image formats.  
0H No stretch (default)  
1H Histogram stretch  
Example of Histogram Stretch at 0H: Example of Histogram Stretch at 1H:  
7 - 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
I - Invert Image  
Invert image is used to rotate the image around the X or Y axis.  
1ix Invert around the X axis (flips picture upside down)  
1iy Invert around the Y axis (flips picture left to right)  
Example of image not  
inverted:  
Example of image  
with Invert Image set to with Invert Image set  
1ix:  
Example of image  
to 1iy:  
IF- Noise Reduction  
Used to reduce the salt and pepper noise in an image.  
0if No salt and pepper noise reduction (default)  
1if Salt and pepper noise reduction  
Example of Noise Reduction Off (0if):  
Example of Noise Reduction On (1if):  
7 - 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
IR - Image Rotate  
0ir Image as snapped (rightside up) (default)  
1ir Rotate image 90 degrees to the right  
2ir Rotate image 180 degrees (upside down)  
3ir Rotate image 90 degrees to the left  
Example of Image Rotate set to 2ir:  
Example of Image Rotate set to 3ir:  
Example of Image Rotate set to 0ir:  
Example of Image Rotate set to 1ir:  
J - JPEG Image Quality  
Sets the desired quality when the JPEG image format is selected. Higher numbers result in higher quality, but larger files.  
Smaller numbers result in greater amounts of lossy compression, faster transmission times, lower quality, but smaller files.  
(Default = 50)  
nJ Image is compressed as much as possible while preserving quality factor of n (n = 0 - 100)  
0J worst quality (smallest file)  
100Jbest quality (largest file)  
K - Gamma Correction  
Gamma measures the brightness of midtone values produced by the image. You can brighten or darken an image using  
gamma correction. A higher gamma correction yields an overall brighter image. The lower the setting, the darker the  
image. The optimal setting for text images is 50K.  
0K Gamma correction off (default)  
50K Apply gamma correction for brightening typical document image  
nK Apply gamma correction factor n (n = 0-1,000)  
Example of Gamma  
Correction set to 0K:  
Example of Gamma  
Correction set to 50K:  
Example of Gamma  
Correction set to 255K:  
L, R, T, B, M - Image Cropping  
Ships a window of the image by specifying the left, right, top, and bottom pixel coordinates. Device columns are numbered  
0 through 1279, and device rows are numbered 0 through 959.  
7 - 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
nL The left edge of the shipped image corresponds to column n of the image in memory. Range: 000 - 843. (Default  
= 0)  
nR The right edge of the shipped image corresponds to column n - 1 of the image in memory. Range: 000 - 843.  
(Default = all columns)  
nT The top edge of the shipped image corresponds to row n of the image in memory. Range: 000 - 639. (Default = 0)  
nB The bottom edge of the shipped image corresponds to row n - 1 of the image in memory. Range: 000 - 639.  
(Default = all rows)  
Uncropped Image:  
Example of Image Crop  
set to 300R:  
Example of Image  
Crop set to 300L:  
Example of Image Crop set to 200B:  
Example of Image Crop set to 200T:  
Alternately, specify the number of pixels to cut from the outside margin of the image; thus only the center pixels are trans-  
mitted.  
nM Margin: cut n columns from the left, n + 1 columns from the right, n rows from the top, and n + 1 rows from the  
bottom of the image. Ship the remaining center pixels. Range: 0 - 238.  
(Default = 0, or full image)  
Example of Image Crop set to 238M:  
P - Protocol  
Used for shipping an image. Protocol covers two features of the image data being sent to the host. It addresses the proto-  
col used to send the data (Hmodem, which is an Xmodem 1K variant that has additional header information), and the for-  
mat of the image data that is sent.  
0P None (raw data)  
2P None (default for USB)  
3P Hmodem compressed (default for RS232)  
4P Hmodem  
S - Pixel Ship  
Pixel Ship sizes an image in proportion to its original size. It decimates the image by shipping only certain, regularly  
spaced pixels. For example, 4S would transmit every fourth pixel from every fourth line. The smaller number of pixels  
shipped, the smaller the image, however, after a certain point the image becomes unusable.  
1S ship every pixel (default)  
2S ship every 2nd pixel, both horizontally and vertically  
7 - 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
3S ship every 3rd pixel, both horizontally and vertically  
Example of Pixel  
Example of Pixel  
Ship set to 3S:  
Example of Pixel Ship set to 1S:  
Ship set to 2S:  
U - Document Image Filter  
Allows you to input parameters to sharpen the edges and smooth the area between the edges of text in an image. This fil-  
ter should be used with gamma correction (see page 7-7), with the scanner in a stand, and the image captured using the  
command:  
IMGSNP1P0L168W90%32D  
This filter typically provides better JPEG compression than the standard E - Edge Sharpen command (see page 7-9). This  
filter also works well when shipping pure black and white images (1 bit per pixel). The optimal setting is 26U.  
0U Document image filter off (default)  
26U Apply document image filter for typical document image  
nU Apply document image filter using grayscale threshold n. Use lower numbers when the image contrast is lower.  
1U will have a similar effect to setting E - Edge Sharpen (page 7-5) to 22e. Range: 0-255.  
Example of Document  
Image Filter set to 0U:  
Example of Document  
Image Filter set to 26U:  
V - Blur Image  
Smooths transitions by averaging the pixels next to the hard edges of defined lines and shaded areas in an image.  
0V Don’t blur (default)  
1V Blur  
Example of Blur Image Off (0V):  
Example of Blur Image On (1V):  
W - Histogram Ship  
A histogram gives a quick picture of the tonal range of an image, or key type. A low-key image has detail concentrated in  
the shadows; a high-key image has detail concentrated in the highlights; and an average-key image has detail concentrated  
in the midtones. This modifier ships the histogram for an image.  
0W Don’t ship histogram (default)  
7 - 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
1W Ship histogram  
Image used for histogram:  
Histogram of image at left:  
Image Size Compatibility  
If you have applications that expect an image ship to return exactly 640x480 pixels, scan the Force VGA Resolution bar  
code. Default = Native Resolution.  
Force VGA Resolution  
* Native Resolution  
Intelligent Signature Capture - IMGBOX  
IMGBOX allows you to configure the size and location of a signature capture area relative to its proximity to a bar code. This  
allows you to tailor a signature capture area to a specific form. In order to use IMGBOX, you need a set form where the signa-  
ture box location is in a known location relative to a bar code. You can input the overall size of the signature area, as well as  
specify how far the signature area is from the bar code, vertically and horizontally. You can also set the resolution and file format  
for the final output of the signature capture image.  
Note: IMGBOX commands can only be triggered by one of the following types of bar codes: PDF417, Code 39, Code 128, Aztec,  
Codabar, and Interleaved 2 of 5. Once one of these symbologies has been read, the image is retained for a possible  
IMGBOX command.  
Signature Capture Optimize  
If you will be using your scan engine to capture signatures frequently, you should optimize it for this purpose. However, the  
speed of scanning bar codes may be slowed when this mode is enabled. Default = Off.  
Optimize On  
* Optimize Off  
7 - 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
The following IMGBOX example was executed and viewed using QuickView software. This software is available at  
www.honeywellaidc.com. Click on Software Downloads. Select 4600r from the Products list, then select QuickView Soft-  
ware Utility.  
Below is an example of a signature capture application. In this example, the aimer is centered over the signature capture area  
and the trigger is pressed. A single beep is emitted, indicating that the scan engine has read a Code 128 bar code and the data  
has been transferred to the host. An IMGBOX command may now be sent from the host to specify the coordinates of the signa-  
ture capture area below that code, and indicating that only that area containing the signature should be transferred as an image  
to the host.  
To see this example, align the aimer with the signature area (not with the bar code), then press the trigger.  
Send the following IMGBOX command string after the button push:  
Example: IMGBOX245w37h55y.  
Note: Case is not important in the command string. It is used here only for clarity.  
The following image is captured:  
The IMGBOX commands have many different modifiers that can be used to change the size and appearance of the signature  
image output by the scan engine. Modifiers affect the image that is transmitted, but do not affect the image in memory. Any  
number of modifiers may be appended to the IMGBOX command.  
Note: The IMGBOX command will return a NAK unless a window size (width and height) are specified. See H - Height of  
Signature Capture Area (page 7-12) and W - Width of Signature Capture Area (page 7-13).  
IMGBOX Modifiers  
A - Output Image Width  
This option is used to size the image horizontally. If using this option, set the resolution (R) to zero.  
Example of Image Width set to 200A:  
Example of Image Width set to 600A:  
B - Output Image Height  
7 - 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
This option is used to size the image vertically. If using this option, set the resolution (R) to zero.  
Example of Image Height set to 50B:  
Example of Image Height set to 100B:  
D - Pixel Depth  
This indicates the number of bits per pixel in the transmitted image, which defines whether it will be grayscale or black and  
white.  
8D 8 bits per pixel, grayscale image (default)  
1D 1 bit per pixel, black and white image  
F - File Format  
This option indicates the type of file format in which to save the image.  
0F KIM format  
1F TIFF binary  
2F TIFF binary group 4, compressed  
3F TIFF grayscale  
4F Uncompressed Binary  
5F Uncompressed grayscale  
6F JPEG image (default)  
7F Outlined image  
8F BMP format  
H - Height of Signature Capture Area  
The height of the signature capture area must be measured in inches divided by .01. In the example, the height of the area  
to be captured is 3/8 inch, resulting in a value of H = .375/0.01 = 37.5.  
Example: IMGBOX245w37h55y.  
K - Gamma Correction  
Gamma measures the brightness of midtone values produced by the image. You can brighten or darken an image using  
gamma correction. A higher gamma correction yields an overall brighter image. The lower the setting, the darker the  
image. The optimal setting for text images is 50K.  
0K Gamma correction off (default)  
50K Apply gamma correction for brightening typical document image  
7 - 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
nK Apply gamma correction factor n (n = 1-255)  
Example of Gamma  
Correction set to 0K:  
Example of Gamma Correction  
set to 50K:  
Example of Gamma Correction  
set to 255K:  
R - Resolution of Signature Capture Area  
The resolution is the number of pixels that the scan engine outputs per each minimum bar width. The higher the value for  
R, the higher the quality of the image, but also the larger the file size. Values begin at 1000. The scan engine automatically  
inserts a decimal point between the first and second digit. For example, use 2500 to specify a resolution of 2.5. Set to zero  
when using the A and B modifiers (see A - Output Image Width and B - Output Image Height on page 7-11).  
Example of Resolution set to 0R:  
Example of Resolution set to 1000R:  
Example of Resolution set to 2000R:  
S - Bar Code Aspect Ratio  
All dimensions used in IMGBOX are measured as multiples of the minimum element size of the bar code. The bar code  
aspect ratio allows you to set the ratio of the bar code height to the narrow element width. In the example, the narrow ele-  
ment width is .010 inches and the bar code height is 0.400 inches, resulting in a value of S = 0.4/0.01 = 40.  
W - Width of Signature Capture Area  
The width of the signature capture area must be measured in inches divided by .01. In the example, the width of the area  
to be captured is 2.4 inches, resulting in a value of W = 2.4/0.01 = 240. (A value of 245 was used in the example to accom-  
modate a slightly wider image area.)  
Example: IMGBOX245w37h55y.  
X - Horizontal Bar Code Offset  
7 - 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The horizontal bar code offset allows you to offset the horizontal center of the signature capture area. Positive values move  
the horizontal center to the right and negative values to the left. Measurements are in multiples of the minimum bar width.  
Example of Horizontal Offset set to 75X:  
Example of Horizontal Offset set to -75X:  
Y - Vertical Bar Code Offset  
The vertical bar code offset allows you to offset the vertical center of the signature capture area. Negative numbers indi-  
cate that the signature capture is above the bar code, and positive numbers indicate that the area is below the bar code.  
Measurements are in multiples of the minimum bar width.  
Example of Vertical Offset set to -7Y:  
Example of Vertical Offset set to 65Y:  
RF Default Imaging Device  
The scan engine supports imaging command processing (IMGSHP, IMGSNP, IMGBOX) so that EZConfig-Scanning (see page  
9-3) and other applications are able to perform imaging functions as if they were communicating directly with a scanner. To  
accomplish this, the scanner uses a menu command called RF_DID (RF Default Imaging Device). RF_DID is the name of the  
scanner (BT_NAM) that is to receive imaging commands. The default for RF_DID is “*”indicating that imaging commands are to  
be sent to all associated scanners. Change this setting to RF_DIDscanner_name to ensure that they are sent to a particular  
scanner. Refer to "Paging" on page 3-7 to generate a report containing the port, work group, scanner name, and address for  
each scanner. Refer to "Scanner Name" on page 3-18 set a unique name for each scanner.  
7 - 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
8
Interface Keys  
Keyboard Function Relationships  
The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to all terminals that can  
be used with the scan engine. Refer to page 2-15 enable Control + X (Control + ASCII) Mode.  
Function Code  
HEX/ASCII Value  
Full ASCII (CTRL + X Mode)  
NUL  
SOH  
STX  
ETX  
EOT  
ENQ  
ACK  
BEL  
BS  
00  
01  
02  
03  
04  
05  
06  
07  
08  
09  
0A  
0B  
0C  
0D  
0E  
0F  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
1A  
1B  
1C  
1D  
1E  
1F  
@
A
B
C
D
E
F
G
H
I
HT  
LF  
J
VT  
K
L
FF  
CR  
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
SO  
SI  
DLE  
DC1  
DC2  
DC3  
DC4  
NAK  
SYN  
ETB  
CAN  
EM  
SUB  
ESC  
FS  
\
GS  
]
RS  
^
US  
_
The last five characters in the Full ASCII “CTRL”+ column ( [ \ ] 6 - ), apply to US only. The following chart indicates the equiva-  
lents of these five characters for different countries.  
Country  
Codes  
United States  
Belgium  
[
\
]
6
6
6
6
6
6
6
6
-
-
-
=
-
-
-
-
[
<
<
8
Ã
\
]
Scandinavia  
France  
8
^
9
$
+
+
. .  
]
Germany  
Italy  
Switzerland  
United Kingdom  
<
¢
[
8 - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Country  
Codes  
Denmark  
Norway  
Spain  
8
8
[
\
\
\
9
9
]
6
6
6
-
-
-
8 - 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Supported Interface Keys  
IBM PC/AT and  
Compatibles,  
USB PC  
Apple Mac/iMac  
Supported Keys  
ASCII  
HEX  
Keyboard  
NUL  
SOH  
STX  
ETX  
EOT  
ENQ  
ACK  
BEL  
BS  
HT  
LF  
VT  
FF  
00  
01  
02  
03  
04  
05  
06  
07  
08  
09  
0A  
0B  
0C  
0D  
0E  
0F  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
1A  
1B  
1C  
1D  
1E  
1F  
7F  
Reserved  
Enter (KP)  
Cap Lock  
ALT make  
ALT break  
CTRL make  
CTRL break  
CR/Enter  
Reserved  
Tab  
Reserved  
Tab  
Delete  
CR/Enter  
Insert  
Escape  
F11  
Home  
Print  
Back Space  
Back Tab  
F12  
Reserved  
Enter/Numpad Enter  
CAPS  
ALT make  
ALT break  
CNTRL make  
CNTRL break  
RETURN  
APPLE make  
TAB  
APPLE break  
TAB  
Del  
RETURN  
Ins Help  
ESC  
F11  
Home  
Prnt Scrn  
BACKSPACE  
LSHIFT TAB  
F12  
F1  
F2  
F3  
F4  
CR  
SO  
SI  
DLE  
DC1  
DC2  
DC3  
DC4  
NAK  
SYN  
ETB  
CAN  
EM  
SUB  
ESC  
FS  
GS  
RS  
F1  
F2  
F3  
F4  
F5  
F6  
F7  
F8  
F5  
F6  
F7  
F8  
F9  
F10  
F9  
F10  
BACKSPACE  
US  
DEL  
8 - 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
8 - 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
Utilities  
To Add a Test Code I.D. Prefix to All Symbologies  
This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts,  
beginning on page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes,  
then programs a Code I.D. prefix for all symbologies. This is a temporary setting that will be removed when the unit is power  
cycled.  
Add Code I.D. Prefix to  
All Symbologies (Temporary)  
Show Decoder Revision  
Scan the bar code below to output the decoder revision.  
Show Decoder Revision  
Show Scan Driver Revision  
Scan the bar code below to output the scan driver revision. The scan driver controls image capture.  
Show Scan Driver Revision  
Show Software Revision  
Scan the bar code below to output the current software revision, unit serial number, and other product information for the  
engine.  
Show Software Revision  
Show Data Format  
Scan the bar code below to show current data format settings.  
DFMBK3?.  
Data Format Settings  
9 - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Test Menu  
When you scan the Test Menu On code, then scan a programming code in this manual, the scan engine displays the content of  
a programming code. The programming function will still occur, but in addition, the content of that programming code is output  
to the terminal.  
Note: This feature should not be used during normal scan engine operation.  
On  
* Off  
TotalFreedom  
TotalFreedom is an open system architecture that makes it possible for you create applications that reside on your scan engine.  
Decoding apps and Data Formatting apps can be created using TotalFreedom. For further information about TotalFreedom, go  
to our website at www.honeywellaidc.com.  
Application Plug-Ins (Apps)  
Any apps that you are using can be turned off or on by scanning the following bar codes. Apps are stored in groups: Decoding,  
and Formatting. You can enable and disable these groups of apps by scanning that group’s On or Off bar code below. You can  
also scan the List Apps bar code to output a list of all your apps.  
* Decoding Apps On  
Decoding Apps Off  
* Formatting Apps On  
Formatting Apps Off  
List Apps  
Note: You must reset your device in order for the apps setting to take effect.  
9 - 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
EZConfig-Scanning Introduction  
EZConfig-Scanning provides a wide range of PC-based programming functions that can be performed on a scan engine con-  
nected to your PC's COM port. EZConfig-Scanning allows you to download upgrades to the scan engine's firmware, change  
programmed parameters, and create and print programming bar codes. Using EZConfig-Scanning, you can even save/open  
the programming parameters for a scan engine. This saved file can be e-mailed or, if required, you can create a single bar code  
that contains all the customized programming parameters and mail or fax that bar code to any location. Users in other locations  
can scan the bar code to load in the customized programming.  
To communicate with a scan engine, EZConfig-Scanning requires that the PC have at least one available serial communication  
port, or a serial port emulation using a physical USB port. If you are using the serial port and RS232 cable, an external power  
supply is required. When using a USB serial port emulation, only a USB cable is required.  
EZConfig-Scanning Operations  
The EZConfig-Scanning software performs the following operations:  
Scan Data  
Scan Data allows you to scan bar codes and display the bar code data in a window. Scan Data lets you send serial  
commands to the scan engine and receive scan engine response that can be seen in the Scan Data window. The data  
displayed in the Scan Data window can either be saved in a file or printed.  
Configure  
Configure displays the programming and configuration data of the scan engine. The scan engine's programming and  
configuration data is grouped into different categories. Each category is displayed as a tree item under the "Configure"  
tree node in the application explorer. When one of these tree nodes is clicked, the right-hand side is loaded with the  
parameters' form belonging to that particular category. The "Configure" tree option has all the programming and con-  
figuration parameters specified for a scan engine. You can set or modify these parameters as required. You can later  
write the modified settings to the scan engine, or save them to a dcf file.  
Imaging  
Imaging provides all the image-related functions that a 2D scan engine can perform. You can capture an image using  
the current settings, and the image will be displayed in an image window. Images captured from the scan engine can  
be saved to files in different image formats. You can modify the image settings and save the image settings to an INI  
file, which can be loaded later to capture new images. Imaging also lets you preview the images continuously captured  
by the scan engine.  
Installing EZConfig-Scanning from the Web  
Note: EZConfig-Scanning requires .NET software. If .NET is not installed on your PC, you will be prompted to install it  
during the EZConfig-Scanning installation.  
1. Access the Honeywell web site at www.honeywellaidc.com  
2. Click on the Resources tab. Select Download.  
3. Click on the dropdown for Select Product Number. Click on your product number.  
4. Click on the listing for EZConfig-Scanning.  
5. When prompted, select Save File, and save the files to the c:\windows\temp directory.  
6. Once you have finished downloading the file, exit the web site.  
7. Using Explorer, go to the c:\windows\temp file.  
8. Double click on the Setup.exe file. Follow the screen prompts to install the EZConfig-Scanning program.  
9. If you’ve selected the defaults during installation, you can click on Start Menu-All Programs-Honeywell-EZConfig-  
Scanning.  
9 - 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Resetting the Factory Defaults  
This selection erases all your settings and resets the scan engine to the original factory defaults. It also disables all  
plugins.  
If you aren’t sure what programming options are in your scan engine, or you’ve changed some options and want to restore the  
scan engine to factory default settings, first scan the Remove Custom Defaults bar code, then scan Activate Defaults. This  
resets the scan engine to the factory default settings.  
Remove Custom Defaults  
Activate Defaults  
The Menu Commands, beginning on page 10-4 list the factory default settings for each of the commands (indicated by an aster-  
isk (*) on the programming pages).  
9 - 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
10  
Serial Programming Commands  
The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the  
programming bar codes will program the scan engine. For complete descriptions and examples of each serial programming  
command, refer to the corresponding programming bar code in this manual.  
The device must be set to an RS232 interface (see page 2-1). The following commands can be sent via a PC COM port using  
terminal emulation software.  
Conventions  
The following conventions are used for menu and query command descriptions:  
parameterA label representing the actual value you should send as part of a command.  
[option] An optional part of a command.  
{Data} Alternatives in a command.  
bold  
Names of menus, menu commands, buttons, dialog boxes, and windows that appear on the screen.  
Menu Command Syntax  
Menu commands have the following syntax (spaces have been used for clarity only):  
Prefix [:Name:] Tag SubTag {Data} [, SubTag {Data}] [; Tag SubTag {Data}] […] Storage  
Prefix Three ASCII characters: SYN M CR (ASCII 22,77,13).  
Tag  
A 3 character case-insensitive field that identifies the desired menu command group. For example, all RS232  
configuration settings are identified with a Tag of 232.  
SubTag A 3 character case-insensitive field that identifies the desired menu command within the tag group. For example, the  
SubTag for the RS232 baud rate is BAD.  
Data  
The new value for a menu setting, identified by the Tag and SubTag.  
Storage A single character that specifies the storage table to which the command is applied. An exclamation point (!) performs  
the command’s operation on the device’s volatile menu configuration table. A period (.) performs the command’s  
operation on the device’s non-volatile menu configuration table. Use the non-volatile table only for semi-permanent  
changes you want saved through a power cycle.  
Query Commands  
Several special characters can be used to query the device about its settings.  
^
?
*
What is the default value for the setting(s).  
What is the device’s current value for the setting(s).  
What is the range of possible values for the setting(s). (The device’s response uses a dash (-) to indicate a  
continuous range of values. A pipe (|) separates items in a list of non-continuous values.)  
:Name: Field Usage (Optional)  
This command returns the query information from the scan engine.  
Tag Field Usage  
When a query is used in place of a Tag field, the query applies to the entire set of commands available for the particular  
storage table indicated by the Storage field of the command. In this case, the SubTag and Data fields should not be used  
because they are ignored by the device.  
SubTag Field Usage  
When a query is used in place of a SubTag field, the query applies only to the subset of commands available that match the  
Tag field. In this case, the Data field should not be used because it is ignored by the device.  
10 - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Data Field Usage  
When a query is used in place of the Data field, the query applies only to the specific command identified by the Tag and  
SubTag fields.  
Concatenation of Multiple Commands  
Multiple commands can be issued within one Prefix/Storage sequence. Only the Tag, SubTag, and Data fields must be  
repeated for each command in the sequence. If additional commands are to be applied to the same Tag, then the new  
command sequence is separated with a comma (,) and only the SubTag and Data fields of the additional command are  
issued. If the additional command requires a different Tag field, the command is separated from previous commands by a  
semicolon (;).  
Responses  
The device responds to serial commands with one of three responses:  
ACK  
ENQ  
NAK  
Indicates a good command which has been processed.  
Indicates an invalid Tag or SubTag command.  
Indicates the command was good, but the Data field entry was out of the allowable range for this Tag and SubTag  
combination, e.g., an entry for a minimum message length of 100 when the field will only accept 2 characters.  
When responding, the device echoes back the command sequence with the status character inserted directly before each  
of the punctuation marks (the period, exclamation point, comma, or semicolon) in the command.  
Examples of Query Commands  
In the following examples, a bracketed notation [ ] depicts a non-displayable response.  
Example: What is the range of possible values for Codabar Coding Enable?  
Enter:  
cbrena*.  
Response: CBRENA0-1[ACK]  
This response indicates that Codabar Coding Enable (CBRENA) has a range of values from 0 to 1 (off and on).  
Example: What is the default value for Codabar Coding Enable?  
Enter:  
cbrena^.  
Response: CBRENA1[ACK]  
This response indicates that the default setting for Codabar Coding Enable (CBRENA) is 1, or on.  
Example: What is the device’s current setting for Codabar Coding Enable?  
Enter:  
cbrena?.  
Response: CBRENA1[ACK]  
This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on.  
Example: What are the device’s settings for all Codabar selections?  
Enter:  
cbr?.  
Response: CBRENA1[ACK],  
SSX0[ACK],  
CK20[ACK],  
CCT1[ACK],  
MIN2[ACK],  
MAX60[ACK],  
DFT[ACK].  
This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on;  
the Start/Stop Character (SSX) is set to 0, or Don’t Transmit;  
the Check Character (CK2) is set to 0, or Not Required;  
concatenation (CCT) is set to 1, or Enabled;  
10 - 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
the Minimum Message Length (MIN) is set to 2 characters;  
the Maximum Message Length (MAX) is set to 60 characters;  
and the Default setting (DFT) has no value.  
Trigger Commands  
You can activate and deactivate the scan engine with serial trigger commands. First, the scan engine must be put in Manual  
Trigger Mode by scanning a Manual Trigger Mode bar code (page 3-5), or by sending a serial menu command for triggering  
(page 3-5). Once the scan engine is in serial trigger mode, the trigger is activated and deactivated by sending the following  
commands:  
Activate: SYN T CR  
Deactivate: SYN U CR  
The scan engine scans until a bar code has been read, until the deactivate command is sent, or until the serial time-out has  
been reached (see "Read Time-Out" on page 3-5 for a description, and the serial command on page 10-8).  
Resetting the Custom Defaults  
If you want the custom default settings restored to your scan engine, scan the Activate Custom Defaults bar code below. This  
resets the scan engine to the custom default settings. If there are no custom defaults, it will reset the scan engine to the factory  
default settings. Any settings that have not been specified through the custom defaults will be defaulted to the factory default  
settings.  
Activate Custom Defaults  
The charts on the following pages list the factory default settings for each of the commands (indicated by an asterisk (*) on the  
programming pages).  
10 - 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Menu Commands  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Product Default Settings  
Setting Custom Defaults  
Set Custom Defaults  
MNUCDP  
MNUCDS  
DEFALT  
1-4  
1-4  
1-5  
Save Custom Defaults  
Activate Custom Defaults  
Resetting the Custom Defaults  
Programming the Interface  
Plug and Play Codes  
Keyboard Wedge:  
IBM PC AT and Compatibles with  
CR suffix  
PAP_AT  
PAPLTD  
2-1  
2-1  
Laptop Direct Connect with CR  
suffix  
RS232 Serial Port  
PAP232  
2-1  
2-2  
2-2  
2-2  
2-2  
2-2  
2-2  
2-3  
2-3  
2-3  
2-3  
2-3  
2-3  
2-3  
2-3  
2-4  
2-4  
2-4  
2-4  
2-5  
2-5  
2-5  
Plug and Play Codes: IBM SurePos  
Plug and Play Codes: USB  
USB IBM SurePos Handheld  
USB IBM SurePos Tabletop  
USB Keyboard (PC)  
USB Keyboard (Mac)  
USB Japanese Keyboard (PC)  
USB HID  
PAPSPH  
PAPSPT  
PAP124  
PAP125  
TRMUSB134  
PAP131  
USB Serial  
TRMUSB130  
USBCTS1  
USBCTS0  
USBACK1  
USBACK0  
REMIFC0  
REMIFC1  
PAPRBY  
PAPGLB  
PAPBIO  
CTS/RTS Emulation On  
CTS/RTS Emulation Off*  
ACK/NAK Mode On  
ACK/NAK Mode Off*  
ReM Off  
Remote MasterMind for USB  
Plug and Play Codes  
ReM On  
Verifone Ruby Terminal  
Gilbarco Terminal  
Honeywell Bioptic Aux Port  
Datalogic Magellan Aux Port  
NCR Bioptic Aux Port  
Wincor Nixdorf Terminal  
Wincor Nixdorf Beetle  
*U.S.A.  
PAPMAG  
PAPNCR  
PAPWNX  
PAPBTL  
Program Keyboard  
Country  
KBDCTY0  
Albania  
KBDCTY35  
KBDCTY81  
KBDCTY80  
KBDCTY82  
KBDCTY1  
2-5  
2-5  
2-5  
2-6  
2-6  
2-6  
2-6  
2-6  
2-6  
Azeri (Cyrillic)  
Azeri (Latin)  
Belarus  
Belgium  
Bosnia  
KBDCTY33  
KBDCTY16  
KBDCTY59  
KBDCTY52  
Brazil  
Brazil (MS)  
Bulgaria (Cyrillic)  
10 - 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Bulgaria (Latin)  
Canada (French legacy)  
Canada (French)  
Canada (Multilingual)  
Croatia  
KBDCTY53  
KBDCTY54  
KBDCTY18  
KBDCTY55  
KBDCTY32  
KBDCTY15  
KBDCTY40  
KBDCTY39  
KBDCTY38  
KBDCTY8  
2-6  
2-6  
2-6  
2-6  
2-6  
2-7  
2-7  
2-7  
2-7  
2-7  
2-7  
2-7  
2-7  
2-7  
2-7  
2-7  
2-8  
2-8  
2-8  
2-8  
2-8  
2-8  
2-8  
2-8  
2-8  
2-8  
2-8  
2-9  
2-9  
2-9  
2-9  
2-9  
2-9  
2-9  
2-9  
2-9  
2-9  
2-9  
2-10  
2-10  
2-10  
2-10  
2-10  
Czech  
Czech (Programmers)  
Czech (QWERTY)  
Czech (QWERTZ)  
Denmark  
Dutch (Netherlands)  
Estonia  
KBDCTY11  
KBDCTY41  
KBDCTY83  
KBDCTY2  
Faroese  
Finland  
France  
KBDCTY3  
Gaelic  
KBDCTY84  
KBDCTY4  
Germany  
Greek  
KBDCTY17  
KBDCTY64  
KBDCTY61  
KBDCTY65  
KBDCTY62  
KBDCTY63  
KBDCTY66  
KBDCTY60  
KBDCTY12  
KBDCTY50  
KBDCTY19  
KBDCTY75  
KBDCTY73  
KBDCTY56  
KBDCTY5  
Greek (220 Latin)  
Greek (220)  
Greek (319 Latin)  
Greek (319)  
Greek (Latin)  
Greek (MS)  
Greek (Polytonic)  
Hebrew  
Hungarian (101 key)  
Hungary  
Iceland  
Irish  
Italian (142)  
Italy  
Japan ASCII  
Kazakh  
KBDCTY28  
KBDCTY78  
KBDCTY79  
KBDCTY14  
KBDCTY42  
KBDCTY43  
KBDCTY44  
KBDCTY45  
KBDCTY34  
KBDCTY74  
KBDCTY86  
Kyrgyz (Cyrillic)  
Latin America  
Latvia  
Latvia (QWERTY)  
Lithuania  
Lithuania (IBM)  
Macedonia  
Malta  
Mongolian (Cyrillic)  
10 - 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Norway  
KBDCTY9  
2-10  
2-10  
2-10  
2-10  
2-10  
2-10  
2-11  
2-11  
2-11  
2-11  
2-11  
2-11  
2-11  
2-11  
2-11  
2-11  
2-11  
2-12  
2-12  
2-12  
2-12  
2-12  
2-12  
2-12  
2-12  
2-12  
2-13  
2-12  
2-12  
2-13  
2-13  
2-14  
2-14  
Poland  
KBDCTY20  
KBDCTY57  
KBDCTY58  
KBDCTY13  
KBDCTY25  
KBDCTY26  
KBDCTY67  
KBDCTY68  
KBDCTY21  
KBDCTY37  
KBDCTY36  
KBDCTY22  
KBDCTY49  
KBDCTY48  
KBDCTY31  
KBDCTY10  
KBDCTY51  
KBDCTY23  
KBDCTY29  
KBDCTY6  
Polish (214)  
Polish (Programmers)  
Portugal  
Romania  
Russia  
Russian (MS)  
Russian (Typewriter)  
SCS  
Serbia (Cyrillic)  
Serbia (Latin)  
Slovakia  
Slovakia (QWERTY)  
Slovakia (QWERTZ)  
Slovenia  
Spain  
Spanish variation  
Sweden  
Switzerland (French)  
Switzerland (German)  
Tatar  
KBDCTY85  
KBDCTY27  
KBDCTY24  
KBDCTY76  
KBDCTY7  
Turkey F  
Turkey Q  
Ukrainian  
United Kingdom  
United Stated (Dvorak right)  
United States (Dvorak left)  
United States (Dvorak)  
United States (International)  
Uzbek (Cyrillic)  
*Keyboard Conversion Off  
KBDCTY89  
KBDCTY88  
KBDCTY87  
KBDCTY30  
KBDCTY77  
KBDCNV0  
KBDCNV1  
Keyboard Conversion  
Keyboard Style  
Convert all Characters to Upper  
Case  
Convert all Characters to Lower  
Case  
KBDCNV2  
2-14  
*Regular  
KBDSTY0  
KBDSTY1  
KBDSTY2  
KBDSTY6  
KBDSTY5  
2-13  
2-13  
2-13  
2-13  
2-14  
Caps Lock  
Shift Lock  
Automatic Caps Lock  
Emulate External  
Keyboard  
10 - 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Control Character Output  
*Control Character Output Off  
*Control Character Output On  
*Control + X Off  
KBDNPE0  
KBDNPE1  
KBDCAS0  
KBDCAS1  
KBDCAS2  
KBDCAS3  
KBDTMD0  
KBDTMD1  
KBDNPS0  
KBDNPS1  
KBDADC0  
KBDADC1  
232BAD0  
232BAD1  
232BAD2  
232BAD3  
232BAD4  
232BAD5  
232BAD6  
232BAD7  
232BAD8  
232BAD9  
2-14  
2-14  
2-15  
2-15  
2-15  
2-15  
2-15  
2-15  
2-15  
2-15  
2-16  
2-16  
2-16  
2-16  
2-16  
2-16  
2-16  
2-17  
2-16  
2-17  
2-17  
2-17  
2-17  
Keyboard Modifiers  
DOS Mode Control + X  
Windows Mode Control + X  
Windows Mode Prefix/Suffix Off  
*Turbo Mode Off  
Turbo Mode On  
*Numeric Keypad Off  
Numeric Keypad On  
*Auto Direct Connect Off  
Auto Direct Connect On  
300 BPS  
Baud Rate  
600 BPS  
1200 BPS  
2400 BPS  
4800 BPS  
*9600 BPS  
19200 BPS  
38400 BPS  
57600 BPS  
115200 BPS  
Word Length: Data Bits, Stop Bits,  
and Parity  
7 Data, 1 Stop, Parity Even  
232WRD3  
232WRD0  
232WRD6  
232WRD4  
232WRD1  
232WRD7  
232WRD5  
232WRD2  
232WRD8  
232WRD14  
232LPT###  
232CTS0  
232CTS1  
232CTS2  
232CTS3  
232DEL####  
232XON0  
232XON1  
232ACK0  
232ACK1  
232SDY  
7 Data, 1 Stop, Parity None  
7 Data, 1 Stop, Parity Odd  
7 Data, 2 Stop, Parity Even  
7 Data, 2 Stop, Parity None  
7 Data, 2 Stop, Parity Odd  
8 Data, 1 Stop, Parity Even  
*8 Data, 1 Stop, Parity None  
8 Data, 1 Stop, Parity Odd  
8 Data, 1 Stop, Parity Mark  
Range 0 - 300 seconds  
*RTS/CTS Off  
2-17  
2-17  
2-17  
2-17  
2-17  
2-18  
2-18  
2-18  
2-18  
2-18  
2-19  
2-18  
2-18  
2-19  
2-19  
2-19  
2-19  
2-19  
2-19  
2-20  
RS232 Receiver Time-out  
RS232 Handshaking  
Flow Control, No Timeout  
Two-Direction Flow Control  
Flow Control with Timeout  
RS232 Timeout  
*XON/XOFF Off  
XON/XOFF On  
*ACK/NAK Off  
ACK/NAK On  
RS232 Stop Mode  
RS232 Stop Mode On  
10 - 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Scanner-Bioptic Packet Mode  
*Packet Mode Off  
Packet Mode On  
232PKT0  
2-20  
2-20  
2-20  
2-20  
2-21  
232PKT2  
Scanner-Bioptic ACK/NAK Mode  
Scanner-Bioptic ACK/NAK Timeout  
*Bioptic ACK/NAK Off  
Bioptic ACK/NAK On  
232NAK0  
232NAK1  
232DLK#####  
ACK/NAK Timeout  
*5100  
Input/Output Selections  
Power Up Beeper  
Power Up Beeper Off - Scanner  
BEPPWR0  
BEPPWR1  
BELBEP1  
3-1  
3-1  
3-1  
3-1  
3-1  
3-1  
3-2  
3-2  
3-2  
3-2  
3-2  
3-2  
3-2  
3-2  
3-2  
3-3  
3-3  
3-3  
3-3  
3-3  
3-3  
3-3  
3-4  
3-4  
3-4  
3-4  
3-4  
3-4  
3-4  
3-4  
3-4  
3-5  
3-5  
3-5  
*Power Up Beeper On - Scanner  
Beep on BEL Character  
Trigger Click  
Beep on BEL On  
*Beep on BEL Off  
BELBEP0  
On  
BEPTRG1  
BEPTRG0  
BEPBEP0  
BEPBEP1  
BEPLVL0  
*Off  
Beeper - Good Read  
Beeper Volume - Good Read  
Off  
*On  
Off  
Low  
BEPLVL1  
Medium  
BEPLVL2  
*High  
BEPLVL3  
Beeper Pitch - Good Read  
(Frequency)  
Low (1600) (min 400Hz)  
*Medium (2700 Hz)  
High (4200) (max 9000Hz)  
*Razz (250) (min 200Hz)  
Medium (3250)  
High (4200) (max 9000Hz)  
*Normal Beep  
Short Beep  
BEPFQ11600  
BEPFQ12700  
BEPFQ14200  
BEPFQ2800  
BEPFQ23250  
BEPFQ24200  
BEPBIP0  
Beeper Pitch - Error (Frequency)  
Beeper Duration - Good Read  
LED - Good Read  
BEPBIP1  
Off  
BEPLED0  
*On  
BEPLED1  
Number of Beeps - Error  
Number of Beeps - Good Read  
Good Read Delay  
*1  
BEPERR3  
BEPERR#  
BEPRPT1  
BEPRPT#  
DLYGRD0  
DLYGRD500  
DLYGRD1000  
DLYGRD1500  
DLYGRD#####  
PAPHHF  
Range 1 - 9  
*1  
Range 1 - 9  
*No Delay  
Short Delay (500 ms)  
Medium Delay (1000 ms)  
Long Delay (1500 ms)  
Range 0 - 30,000 ms  
*Manual Trigger - Normal  
Manual Trigger - Enhanced  
User-Specified Good Read Delay  
Manual Trigger Modes  
PAPHHS  
Serial Trigger Mode  
Presentation Mode  
Read Time-Out  
(0 - 300,000 ms) *30,000  
TRGSTO####  
Presentation Mode  
PAPTPR  
3-5  
10 - 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
LED Illumination - Presentation  
Mode  
Off  
PWRLDC0  
PWRLDC100  
PWRLDC150  
TRGPCK1  
TRGPCK0  
TRGPMS##  
PAPSPN  
3-6  
3-6  
3-6  
3-6  
3-6  
3-6  
3-7  
Low  
*High  
Presentation LED Behavior After  
Decode  
*LEDs On  
LEDs Off  
Range 0-20 (*1)  
Presentation Sensitivity  
Streaming Presentation  
Streaming Presentation Mode -  
Normal  
Streaming Presentation Mode -  
Enhanced  
PAPSPE  
PAPHHC  
PAPSPC  
3-7  
3-7  
3-7  
Mobile Phone Read Mode  
Hand Held Scanning - Mobile  
Phone  
Streaming Presentation - Mobile  
Phone  
Image Snap and Ship  
Hands Free Time-Out  
Reread Delay  
Image Snap and Ship  
Range 0 - 300,000 ms  
Short (500 ms)  
TRGMOD6  
TRGPTO######  
DLYRRD500  
DLYRRD750  
DLYRRD1000  
DLYRRD2000  
DLYRRD#####  
DLY2RR0  
3-7  
3-8  
3-8  
*Medium (750 ms)  
Long (1000 ms)  
Extra Long (2000 ms)  
Range 0 - 30,000 ms  
*2D Reread Delay Off  
Short (1000ms)  
Medium (2000ms)  
Long (3000ms)  
3-8  
3-8  
3-8  
User-Specified  
3-8  
2D Reread Delay  
3-9  
DLY2RR1000  
DLY2RR2000  
DLY2RR3000  
DLY2RR4000  
SCNLED1  
3-9  
3-9  
3-9  
Extra Long (4000ms)  
*Lights On  
3-9  
Illumination Lights  
Aimer Delay  
3-9  
Lights Off  
SCNLED0  
3-9  
200 milliseconds  
400 milliseconds  
*Off (no delay)  
SCNDLY200  
SCNDLY400  
SCNDLY0  
3-10  
3-10  
3-10  
3-10  
3-10  
3-10  
3-11  
3-11  
3-11  
3-11  
User-Specified Aimer Delay  
Aimer Mode  
Range 0 - 4,000 ms  
Off  
SCNDLY####  
SCNAIM0  
*Interlaced  
SCNAIM2  
Centering Window  
Centering On  
DECWIN1  
*Centering Off  
DECWIN0  
Top of Centering Window (*40%)  
DECTOP###  
DECBOT###  
Bottom of Centering Window  
(*60%)  
10 - 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Preferred Symbology  
On  
PRFENA1  
3-12  
3-12  
3-12  
3-12  
3-13  
*Off  
PRFENA0  
High Priority Symbology  
Low Priority Symbology  
PRFCOD##  
PRFBLK##  
PRFPTO####  
Preferred Symbology Timeout  
(*500) Range 100-3000  
Preferred Symbology Default  
PRFDFT  
3-13  
3-15  
3-15  
3-15  
3-15  
3-15  
3-15  
3-16  
3-16  
3-16  
3-16  
3-16  
3-16  
3-17  
Output Sequence Editor  
Partial Sequence  
Enter Sequence  
SEQBLK  
Default Sequence  
SEQDFT  
Transmit Partial Sequence  
SEQTTS1  
SEQTTS0  
SEQ_EN2  
SEQ_EN1  
SEQ_EN0  
SHOTGN1  
SHOTGN0  
SHWNRD1  
SHWNRD0  
VIDREV1  
VIDREV2  
*Discard Partial Sequence  
Require Output Sequence  
Required  
On/Not Required  
*Off  
Multiple Symbols  
No Read  
On  
*Off  
On  
*Off  
Video Reverse  
Video Reverse Only  
Video Reverse and Standard Bar  
Codes  
*Video Reverse Off  
*Upright  
VIDREV0  
ROTATN0  
ROTATN1  
3-17  
3-17  
3-17  
Working Orientation  
Vertical, Bottom to Top (Rotate  
CCW 90°)  
Upside Down  
ROTATN2  
ROTATN3  
3-17  
3-17  
Vertical, Top to Bottom (Rotate CW  
90°)  
Prefix/Suffix Selections  
Add CR Suffix to All Symbologies  
Prefix  
VSUFCR  
PREBK2##  
PRECL2  
4-2  
4-2  
4-2  
4-2  
4-3  
4-3  
4-3  
4-3  
4-3  
4-3  
4-4  
Add Prefix  
Clear One Prefix  
Clear All Prefixes  
Add Suffix  
PRECA2  
Suffix  
SUFBK2##  
SUFCL2  
Clear One Suffix  
Clear All Suffixes  
*Enable  
SUFCA2  
Function Code Transmit  
Intercharacter Delay  
RMVFNC0  
RMVFNC1  
DLYCHR##  
DLYCRX##  
Disable  
Range 0 - 1000 (5ms increments)  
User Specified  
Delay Length  
Intercharacter Delay  
0 - 1000 (5ms increments)  
Character to Trigger Delay  
DLY_XX##  
DLYFNC##  
DLYMSG##  
4-4  
4-4  
4-5  
Interfunction Delay  
Intermessage Delay  
Range 0 - 1000 (5ms increments)  
Range 0 - 1000 (5ms increments)  
10 - 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Data Formatter Selections  
Data Format Editor  
*Default Data Format (None)  
Enter Data Format  
DFMDF3  
DFMBK3##  
DFMCL3  
5-1  
5-2  
Clear One Data Format  
Clear All Data Formats  
Data Formatter Off  
5-2  
DFMCA3  
DFM_EN0  
DFM_EN1  
5-2  
Data Formatter  
5-12  
5-12  
*Data Formatter On,  
Not Required,  
Keep Prefix/Suffix  
Data Format Required,  
Keep Prefix/Suffix  
DFM_EN2  
DFM_EN3  
5-12  
5-12  
Data Formatter On,  
Not Required,  
Drop Prefix/Suffix  
Data Format Required,  
Drop Prefix/Suffix  
DFM_EN4  
DFMDEC0  
DFMDEC1  
5-12  
5-13  
5-13  
Data Format Non-Match Error Tone  
Primary/Alternate Data Formats  
*Data Format Non-Match Error  
Tone On  
Data Format Non-Match Error  
Tone Off  
Primary Data Format  
Data Format 1  
ALTFNM0  
ALTFNM1  
ALTFNM2  
ALTFNM3  
VSAF_0  
5-13  
5-13  
5-13  
5-13  
5-14  
Data Format 2  
Data Format 3  
Single Scan Data Format Change  
Single Scan-Primary  
Data Format  
Single Scan-Data Format 1  
Single Scan-Data Format 2  
Single Scan-Data Format 3  
VSAF_1  
VSAF_2  
VSAF_3  
5-14  
5-14  
5-14  
Symbologies  
All Symbologies  
All Symbologies Off  
All Symbologies On  
ALLENA0  
ALLENA1  
CBRDFT  
6-1  
6-1  
6-2  
Codabar  
Default All Codabar  
Settings  
Off  
CBRENA0  
CBRENA1  
CBRSSX0  
CBRSSX1  
CBRCK20  
CBRCK21  
CBRCK22  
CBRCCT0  
CBRCCT1  
CBRCCT2  
6-2  
6-2  
6-2  
6-2  
6-2  
6-2  
6-2  
6-3  
6-3  
6-3  
*On  
Codabar Start/Stop Char.  
Codabar Check Char.  
*Don’t Transmit  
Transmit  
*No Check Char.  
Validate, But Don’t Transmit  
Validate, and Transmit  
*Off  
Codabar Concatenation  
On  
Require  
10 - 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Codabar Message Length  
Minimum (2 - 60) *4  
Maximum (2 - 60) *60  
CBRMIN##  
CBRMAX##  
C39DFT  
6-3  
6-3  
6-4  
Code 39  
Default All Code 39  
Settings  
Off  
C39ENA0  
C39ENA1  
C39SSX0  
C39SSX1  
C39CK20  
C39CK21  
6-4  
6-4  
6-4  
6-4  
6-4  
6-4  
*On  
Code 39 Start/Stop Char.  
Code 39 Check Char.  
*Don’t Transmit  
Transmit  
*No Check Char.  
Validate, But Don’t  
Transmit  
Validate,  
C39CK22  
6-4  
and Transmit  
Code 39 Message Length  
Code 39 Append  
Minimum (0 - 48) *0  
C39MIN##  
C39MAX##  
C39APP0  
C39APP1  
C39B320  
C39B321  
C39ASC0  
C39ASC1  
C39DCP  
I25DFT  
6-5  
6-5  
6-5  
6-5  
6-5  
6-5  
6-6  
6-6  
6-6  
6-7  
Maximum (0 - 80) *48  
*Off  
On  
Code 32 Pharmaceutical (PARAF)  
Code 39 Full ASCII  
*Off  
On  
*Off  
On  
Code 39 Code Page  
Interleaved 2 of 5  
Default All Interleaved  
2 of 5 Settings  
Off  
I25ENA0  
I25ENA1  
I25CK20  
I25CK21  
6-7  
6-7  
6-7  
6-7  
*On  
Interleaved 2 of 5 Check Digit  
*No Check Char.  
Validate, But Don’t  
Transmit  
Validate, and Transmit  
Minimum (2 - 80) *4  
Maximum (2 - 80) *80  
I25CK22  
I25MIN##  
I25MAX##  
N25DFT  
6-7  
6-7  
6-7  
6-8  
Interleaved 2 of 5 Message Length  
NEC 2 of 5  
Default All NEC  
2 of 5 Settings  
Off  
N25ENA0  
N25ENA1  
N25CK20  
N25CK21  
6-8  
6-8  
6-8  
6-8  
*On  
NEC 2 of 5 Check Digit  
*No Check Char.  
Validate, But Don’t  
Transmit  
Validate, and Transmit  
Minimum (2 - 80) *4  
Maximum (2 - 80) *80  
N25CK22  
N25MIN##  
N25MAX##  
6-8  
6-9  
6-9  
NEC 2 of 5 Message Length  
10 - 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Code 93  
Default All Code 93  
Settings  
C93DFT  
6-9  
Off  
C93ENA0  
C93ENA1  
C93MIN##  
C93MAX##  
C93APP1  
C93APP0  
C93DCP  
6-9  
*On  
6-9  
Code 93 Message Length  
Code 93 Append  
Minimum (0 - 80) *0  
Maximum (0 - 80) *80  
On  
6-9  
6-9  
6-10  
6-10  
6-10  
6-11  
*Off  
Code 93 Code Page  
Code 93 Code Page  
Straight 2 of 5 Industrial  
Default All Straight 2 of 5 Industrial  
Settings  
R25DFT  
*Off  
R25ENA0  
R25ENA1  
R25MIN##  
R25MAX##  
A25DFT  
6-11  
6-11  
6-11  
6-11  
6-12  
On  
Straight 2 of 5 Industrial Message  
Length  
Minimum (1 - 48) *4  
Maximum (1 - 48) *48  
Straight 2 of 5 IATA  
Default All Straight 2 of 5 IATA  
Settings  
Straight 2 of 5 IATA  
*Off  
A25ENA0  
A25ENA1  
A25MIN##  
A25MAX##  
X25DFT  
6-12  
6-12  
6-12  
6-12  
6-13  
On  
Straight 2 of 5 IATA Message  
Length  
Minimum (1 - 48) *4  
Maximum (1 - 48) *48  
Matrix 2 of 5  
Default All Matrix 2 of 5  
Settings  
*Off  
X25ENA0  
X25ENA1  
X25MIN##  
X25MAX##  
C11DFT  
6-13  
6-13  
6-13  
6-13  
6-14  
On  
Matrix 2 of 5 Message Length  
Code 11  
Minimum (1 - 80) *4  
Maximum (1 - 80) *80  
Default All Code 11  
Settings  
*Off  
C11ENA0  
C11ENA1  
C11CK20  
C11CK21  
C11MIN##  
C11MAX##  
128DFT  
6-14  
6-14  
6-14  
6-14  
6-14  
6-14  
6-15  
On  
Code 11 Check Digits Required  
Code 11 Message Length  
Code 128  
1 Check Digit  
*2 Check Digits  
Minimum (1 - 80) *4  
Maximum (1 - 80) *80  
Default All Code 128  
Settings  
Off  
128ENA0  
128ENA1  
ISBENA0  
ISBENA1  
128MIN##  
128MAX##  
6-15  
6-15  
6-15  
6-15  
6-15  
6-15  
*On  
ISBT Concatenation  
*Off  
On  
Code 128 Message Length  
Minimum (0 - 80) *0  
Maximum (0 - 80) *80  
10 - 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Code 128 Append  
*On  
128APP1  
128APP0  
128DCP##  
GS1DFT  
6-16  
6-16  
6-16  
6-17  
6-17  
6-17  
6-17  
6-17  
6-18  
Off  
Code 128 Code Page  
GS1-128  
Code 128 Code Page (*2)  
Default All GS1-128 Settings  
*On  
GS1ENA1  
GS1ENA0  
GS1MIN##  
GS1MAX##  
TELDFT  
Off  
GS1-128 Message Length  
Telepen  
Minimum (1 - 80) *1  
Maximum (0 - 80) *80  
Default All Telepen  
Settings  
*Off  
TELENA0  
TELENA1  
TELOLD0  
TELOLD1  
TELMIN##  
TELMAX##  
UPADFT  
6-18  
6-18  
6-18  
6-18  
6-18  
6-18  
6-19  
On  
Telepen Output  
Telepen Message Length  
UPC-A  
*AIM Telepen Output  
Original Telepen Output  
Minimum (1 - 60) *1  
Maximum (1 - 60) *60  
Default All  
UPC-A Settings  
Off  
UPAENA0  
UPAENA1  
UPACKX0  
UPACKX1  
UPANSX0  
UPANSX1  
UPAAD20  
UPAAD21  
UPAAD50  
UPAAD51  
UPAARQ0  
UPAARQ1  
UPAADS0  
UPAADS1  
CPNENA0  
CPNENA1  
CPNENA2  
CPNGS10  
CPNGS11  
UPEDFT  
6-19  
6-19  
6-19  
6-19  
6-19  
6-19  
6-20  
6-20  
6-20  
6-20  
6-20  
6-20  
6-20  
6-20  
6-21  
6-21  
6-21  
6-21  
6-21  
6-22  
*On  
UPC-A Check Digit  
Off  
*On  
UPC-A Number System  
UPC-A 2 Digit Addenda  
UPC-A 5 Digit Addenda  
UPC-A Addenda Required  
Off  
*On  
*Off  
On  
*Off  
On  
*Not Required  
Required  
UPC-A Addenda  
Separator  
Off  
*On  
UPC-A/EAN-13 with Extended  
Coupon Code  
*Off  
Allow Concatenation  
Require Concatenation  
GS1 Output Off  
GS1 Output On  
Coupon GS1 DataBar Output  
UPC-E0  
Default All UPC-E  
Settings  
Off  
UPEEN00  
UPEEN01  
UPEEXP0  
UPEEXP1  
6-22  
6-22  
6-22  
6-22  
*On  
*Off  
On  
UPC-E0 Expand  
10 - 14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
UPC-E0 Addenda Required  
Required  
UPEARQ1  
UPEARQ0  
UPEADS1  
UPEADS0  
UPECKX0  
UPECKX1  
UPENSX0  
UPENSX1  
UPEAD21  
UPEAD20  
UPEAD51  
UPEAD50  
UPEEN10  
UPEEN11  
E13DFT  
6-22  
6-22  
6-23  
6-23  
6-23  
6-23  
6-23  
6-23  
6-23  
6-23  
6-23  
6-23  
6-24  
6-24  
6-24  
*Not Required  
UPC-E0 Addenda Separator  
UPC-E0 Check Digit  
UPC-E0 Leading Zero  
UPC-E0 Addenda  
*On  
Off  
Off  
*On  
Off  
*On  
2 Digit Addenda On  
*2 Digit Addenda Off  
5 Digit Addenda On  
*5 Digit Addenda Off  
*Off  
UPC-E1  
On  
EAN/JAN-13  
Default All EAN/  
JAN Settings  
Off  
E13ENA0  
E13ENA1  
UPAENA0  
UPAENA1  
E13CKX0  
E13CKX1  
E13AD21  
E13AD20  
E13AD51  
E13AD50  
E13ARQ0  
E13ARQ1  
E13ADS0  
E13ADS1  
E13ISB0  
E13ISB1  
EA8DFT  
6-24  
6-24  
6-24  
6-24  
6-25  
6-25  
6-25  
6-25  
6-25  
6-25  
6-25  
6-25  
6-26  
6-26  
6-26  
6-26  
6-27  
*On  
Convert UPC-A to EAN-13  
EAN/JAN-13 Check Digit  
EAN/JAN-13 2 Digit Addenda  
UPC-A Converted to EAN-13  
Do not Convert UPC-A  
Off  
*On  
2 Digit Addenda On  
*2 Digit Addenda Off  
5 Digit Addenda On  
*5 Digit Addenda Off  
*Not Required  
Required  
EAN/JAN-13 Addenda Required  
EAN/JAN-13 Addenda  
Separator  
Off  
*On  
ISBN Translate  
*Off  
On  
EAN/JAN-8  
Default All EAN/  
JAN 8 Settings  
Off  
EA8ENA0  
EA8ENA1  
EA8CKX0  
EA8CKX1  
EA8AD20  
EA8AD21  
EA8AD50  
EA8AD51  
6-27  
6-27  
6-27  
6-27  
6-27  
6-27  
6-27  
6-27  
*On  
EAN/JAN-8 Check Digit  
EAN/JAN-8 Addenda  
Off  
*On  
*2 Digit Addenda Off  
2 Digit Addenda On  
*5 Digit Addenda Off  
5 Digit Addenda On  
10 - 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
EAN/JAN-8 Addenda Required  
*Not Required  
EA8ARQ0  
EA8ARQ1  
EA8ADS0  
EA8ADS1  
MSIDFT  
6-28  
6-28  
6-28  
6-28  
6-29  
6-29  
6-29  
6-29  
Required  
EAN/JAN-8 Addenda  
Separator  
Off  
*On  
MSI  
Default All MSI Settings  
*Off  
On  
MSIENA0  
MSIENA1  
MSICHK0  
MSI Check Character  
*Validate Type 10, but Don’t  
Transmit  
Validate Type 10 and  
Transmit  
MSICHK1  
MSICHK2  
MSICHK3  
MSICHK4  
MSICHK5  
6-29  
6-29  
6-29  
6-29  
6-30  
Validate 2 Type 10 Chars, but Don’t  
Transmit  
Validate 2 Type 10 Chars and  
Transmit  
Validate Type 10 then Type 11  
Char, but Don’t Transmit  
Validate Type 10 then Type 11  
Char and Transmit  
Disable MSI Check Characters  
Minimum (4 - 48) *4  
MSICHK6  
MSIMIN##  
MSIMAX##  
RSSDFT  
6-30  
6-30  
6-30  
6-31  
MSI Message Length  
Maximum (4 - 48) *48  
GS1 DataBar Omnidirectional  
Default All  
GS1 DataBar Omnidirectional  
Settings  
Off  
RSSENA0  
RSSENA1  
RSLDFT  
6-31  
6-31  
6-31  
*On  
GS1 DataBar Limited  
Default All GS1 DataBar Limited  
Settings  
Off  
RSLENA0  
RSLENA1  
RSEDFT  
6-31  
6-31  
6-32  
*On  
GS1 DataBar Expanded  
Default All GS1 DataBar  
Expanded Settings  
Off  
RSEENA0  
RSEENA1  
RSEMIN##  
RSEMAX##  
TRIENA0  
6-32  
6-32  
6-32  
6-32  
6-32  
6-32  
6-33  
6-33  
6-33  
6-33  
6-33  
*On  
GS1 DataBar Expanded Msg.  
Length  
Minimum (4 - 74) *4  
Maximum (4 - 74) *74  
Trioptic Code  
*Off  
On  
TRIENA1  
Codablock A  
Default All Codablock A Settings  
CBADFT  
*Off  
CBAENA0  
CBAENA1  
CBAMIN###  
CBAMAX###  
On  
Codablock A Msg. Length  
Minimum (1 - 600) *1  
Maximum (1 - 600) *600  
10 - 16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Codablock F  
Default All Codablock F Settings  
CBFDFT  
6-34  
6-34  
6-34  
6-34  
6-34  
6-35  
6-35  
6-35  
6-35  
6-35  
6-36  
6-36  
6-36  
6-36  
6-36  
6-36  
6-36  
6-36  
6-36  
6-37  
6-37  
6-37  
6-37  
6-37  
6-36  
6-38  
6-38  
6-38  
6-38  
6-38  
6-38  
6-38  
6-38  
6-39  
6-39  
6-39  
6-39  
6-39  
6-40  
6-40  
6-40  
6-40  
6-40  
*Off  
CBFENA0  
On  
CBFENA1  
Codablock F Msg. Length  
PDF417  
Minimum (1 - 2048) *1  
CBFMIN####  
CBFMAX####  
PDFDFT  
Maximum (1 - 2048) *2048  
Default All PDF417 Settings  
*On  
PDFENA1  
Off  
PDFENA0  
PDF417 Msg. Length  
MacroPDF417  
Minimum (1-2750) *1  
PDFMIN####  
PDFMAX####  
PDFMAC1  
PDFMAC0  
MPDDFT  
Maximum (1-2750) *2750  
*On  
Off  
MicroPDF417  
Default All Micro PDF417 Settings  
On  
MPDENA1  
MPDENA0  
MPDMIN###  
MPDMAX###  
COMENA1  
COMENA0  
COMUPC1  
COMUPC0  
COMMIN####  
COMMAX####  
EANEMU1  
EANEMU2  
EANEMU3  
EANEMU4  
EANEMU0  
T39ENA1  
*Off  
MicroPDF417 Msg. Length  
GS1 Composite Codes  
UPC/EAN Version  
Minimum (1-366) *1  
Maximum (1-366) *366  
On  
*Off  
On  
*Off  
GS1 Composite Codes Msg. Length Minimum (1-2435) *1  
Maximum (1-2435) *2435  
GS1 Emulation  
GS1-128 Emulation  
GS1 DataBar Emulation  
GS1 Code Expansion Off  
EAN8 to EAN13 Conversion  
*GS1 Emulation Off  
TCIF Linked Code 39  
QR Code  
On  
*Off  
T39ENA0  
Default All QR Code Settings  
QRCDFT  
*On  
QRCENA1  
QRCENA0  
QRCMIN####  
QRCMAX####  
QRCAPP1  
QRCAPP0  
QRCDCP##  
IDMDFT  
Off  
QR Code Msg. Length  
QR Code Append  
Minimum (1-7089) *1  
Maximum (1-7089) *7089  
*On  
Off  
QR Code Page  
Data Matrix  
QR Code Page (*3)  
Default All Data Matrix Settings  
*On  
IDMENA1  
Off  
IDMENA0  
Data Matrix Msg. Length  
Minimum (1-3116) *1  
Maximum (1-3116) *3116  
IDMMIN####  
IDMMAX####  
10 - 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Data Matrix Append  
*On  
IDMAPP1  
6-40  
6-40  
6-40  
6-41  
6-41  
6-41  
6-41  
6-41  
6-42  
6-42  
6-42  
6-42  
6-42  
6-42  
6-42  
6-42  
6-43  
6-43  
6-43  
6-43  
6-43  
Off  
IDMAPP0  
Data Matrix Code Page  
MaxiCode  
Data Matrix Code Page (*51)  
IDMDCP##  
MAXDFT  
Default All MaxiCode Settings  
On  
MAXENA1  
MAXENA0  
MAXMIN###  
MAXMAX###  
AZTDFT  
*Off  
MaxiCode Msg. Length  
Aztec Code  
Minimum (1-150) *1  
Maximum (1-150) *150  
Default All Aztec Code Settings  
*On  
AZTENA1  
AZTENA0  
AZTMIN####  
AZTMAX####  
AZTAPP1  
Off  
Aztec Code Msg. Length  
Aztec Append  
Minimum (1-3832) *1  
Maximum (1-3832) *3832  
*On  
Off  
AZTAPP0  
Aztec Code Page  
Aztec Code Page (*51)  
Default All Han Xin Code Settings  
On  
AZTDCP##  
HX_DFT  
Chinese Sensible (Han Xin) Code  
HX_ENA1  
HX_ENA0  
HX_MIN####  
HX_MAX####  
*Off  
Chinese Sensible (Han Xin) Code  
Msg. Length  
Minimum (1-7833) *1  
Maximum (1-7833) *7833  
Postal Codes - 2D  
2D Postal Codes  
*Off  
POSTAL0  
POSTAL1  
POSTAL7  
POSTAL30  
POSTAL10  
POSTAL3  
POSTAL4  
POSTAL5  
POSTAL9  
POSTAL6  
POSTAL11  
POSTAL2  
6-44  
6-44  
6-44  
6-44  
6-44  
6-44  
6-44  
6-44  
6-44  
6-45  
6-45  
6-45  
Single 2D Postal Codes  
Australian Post On  
British Post On  
Canadian Post On  
Intelligent Mail Bar Code On  
Japanese Post On  
KIX Post On  
Planet Code On  
Postal-4i On  
Postnet On  
Postnet with B and B’ Fields On  
InfoMail On  
10 - 18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Combination 2D Postal Codes  
InfoMail and British Post On  
POSTAL8  
6-45  
6-45  
Intelligent Mail Bar Code and  
Postnet with B and B’ Fields On  
POSTAL20  
Postnet and Postal-4i On  
POSTAL14  
POSTAL16  
6-45  
6-45  
Postnet and Intelligent Mail Bar  
Code On  
Postal-4i and Intelligent Mail Bar  
Code On  
POSTAL17  
POSTAL19  
6-45  
6-45  
Postal-4i and Postnet with B and B’  
Fields On  
Planet and Postnet On  
POSTAL12  
POSTAL18  
6-45  
6-46  
Planet and Postnet with B and B’  
Fields On  
Planet and Postal-4i On  
POSTAL13  
POSTAL15  
6-46  
6-46  
Planet and Intelligent Mail Bar  
Code On  
Planet, Postnet, and Postal-4i On  
POSTAL21  
POSTAL22  
6-46  
6-46  
Planet, Postnet, and Intelligent  
Mail Bar Code On  
Planet, Postal-4i, and Intelligent  
Mail Bar Code On  
POSTAL23  
POSTAL24  
POSTAL25  
POSTAL26  
6-46  
6-46  
6-46  
6-46  
Combination 2D Postal Codes  
(continued)  
Postnet, Postal-4i, and Intelligent  
Mail Bar Code On  
Planet, Postal-4i, and Postnet with  
B and B’ Fields On  
Planet, Intelligent Mail Bar Code,  
and Postnet with B and B’ Fields  
On  
Postal-4i, Intelligent Mail Bar  
Code, and Postnet with B and B’  
Fields On  
POSTAL27  
6-46  
Planet, Postal-4i, Intelligent Mail  
Bar Code, and Postnet On  
POSTAL28  
POSTAL29  
6-47  
6-46  
Planet, Postal-4i, Intelligent Mail  
Bar Code, and Postnet with B and  
B’ Fields On  
Planet Code Check Digit  
Postnet Check Digit  
Transmit  
PLNCKX1  
PLNCKX0  
NETCKX1  
NETCKX0  
AUSINT0  
AUSINT1  
AUSINT2  
AUSINT3  
6-47  
6-47  
6-47  
6-47  
6-48  
6-48  
6-48  
6-48  
*Don’t Transmit  
Transmit  
*Don’t Transmit  
Bar Output  
Australian Post Interpretation  
Numeric N Table  
Alphanumeric C Table  
Combination N and C Tables  
10 - 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Postal Codes - Linear  
China Post (Hong Kong 2 of 5)  
Default All China Post (Hong Kong  
2 of 5) Settings  
CPCDFT  
6-48  
*Off  
CPCENA0  
CPCENA1  
CPCMIN##  
CPCMAX##  
KPCDFT  
6-48  
6-48  
6-48  
6-48  
6-49  
6-49  
6-49  
6-49  
6-49  
6-49  
6-49  
On  
China Post (Hong Kong 2 of 5) Msg.  
Length  
Minimum (2 - 80) *4  
Maximum (2 - 80) *80  
Default All Korea Post Settings  
*Off  
Korea Post  
KPCENA0  
KPCENA1  
KPCMIN##  
KPCMAX##  
KPCCHK1  
KPCCHK0  
On  
Korea Post Msg. Length  
Korea Post Check Digit  
Minimum (2 - 80) *4  
Maximum (2 - 80) *48  
Transmit Check Digit  
*Don’t Transmit Check Digit  
Imaging Default Commands  
Image Snap  
Default all Imaging Commands  
Imaging Style - Decoding  
*Imaging Style - Photo  
Imaging Style - Manual  
Beeper On  
IMGDFT  
7-1  
7-1  
7-1  
7-1  
7-1  
7-1  
7-2  
7-2  
7-2  
7-2  
7-2  
7-2  
7-2  
7-2  
7-2  
7-3  
7-3  
7-3  
7-3  
SNPSTY0  
SNPSTY1  
SNPSTY2  
SNPBEP1  
SNPBEP0  
SNPTRG0  
SNPTRG1  
SNPLED0  
SNPLED1  
SNPEXP  
*Beeper Off  
*Wait for Trigger Off  
Wait for Trigger On  
*LED State - Off  
LED State - On  
Exposure (1-7874 microseconds)  
*Gain - None  
SNPGAN1  
SNPGAN2  
SNPGAN4  
SNPGAN8  
SNPWHT###  
SNPDEL###  
SNPTRY##  
SNPPCT##  
Gain - Medium  
Gain - Heavy  
Gain - Maximum  
Target White Value (0-255) *125  
Delta for Acceptance (0-255) *25  
Update Tries (0-10) *6  
Target Set Point Percentage (1-99)  
*50  
10 - 20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Image Ship  
*Infinity Filter - Off  
Infinity Filter - On  
*Compensation Off  
Compensation On  
IMGINF0  
IMGINF1  
IMGCOR0  
IMGCOR1  
IMGBPP8  
7-3  
7-3  
7-4  
7-4  
7-4  
*Pixel Depth - 8 bits/pixel  
(grayscale)  
Pixel Depth - 1 bit/pixel (B&W)  
*Don’t Sharpen Edges  
Sharpen Edges (0-23)  
*File Format - JPEG  
IMGBPP1  
IMGEDG0  
IMGEDG##  
IMGFMT6  
IMGFMT0  
IMGFMT1  
IMGFMT2  
7-4  
7-5  
7-5  
7-5  
7-5  
7-5  
7-5  
File Format - KIM  
File Format - TIFF binary  
File Format - TIFF binary group 4,  
compressed  
File Format - TIFF grayscale  
IMGFMT3  
IMGFMT4  
7-5  
7-5  
File Format - Uncompressed  
binary  
File Format - Uncompressed  
grayscale  
IMGFMT5  
7-5  
File Format - BMP  
IMGFMT8  
IMGHIS0  
7-5  
7-5  
7-5  
7-6  
7-6  
7-6  
7-6  
7-7  
7-7  
7-7  
7-7  
7-7  
7-7  
7-7  
7-8  
7-8  
7-8  
7-8  
7-8  
7-8  
7-8  
7-8  
7-8  
7-8  
*Histogram Stretch Off  
Histogram Stretch On  
IMGHIS1  
*Noise Reduction Off  
IMGFSP0  
IMGFSP1  
IMGNVX1  
IMGNVY1  
IMGROT0  
IMGROT1  
IMGROT2  
IMGROT3  
IMGJQF###  
IMGGAM0  
IMGGAM###  
IMGWNL###  
IMGWNR###  
IMGWNT###  
IMGWNB###  
IMGMAR###  
IMGXFR0  
IMGXFR2  
IMGXFR3  
IMGXFR4  
IMGSUB1  
Noise Reduction On  
Image Ship (continued)  
Invert Image around X axis  
Invert Image around Y axis  
Rotate Image none  
Rotate Image 90° right  
Rotate Image 180° right  
Rotate Image 90° left  
JPEG Image Quality (0-100) *50  
*Gamma Correction Off  
Gamma Correction On (0-1000)  
Image Crop - Left (0-843) *0  
Image Crop - Right (0-843) *843  
Image Crop - Top (0-639) *0  
Image Crop - Bottom (0-639) *639  
Image Crop - Margin (1-238) *0  
Protocol - None (raw)  
Protocol - None (default USB)  
Protocol - Hmodem Compressed  
Protocol - Hmodem  
Ship Every Pixel  
10 - 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting  
* Indicates default  
Serial Command  
# Indicates a numeric entry  
Selection  
Page  
Image Ship (continued)  
Ship Every 2nd Pixel  
Ship Every 3rd Pixel  
*Document Image Filter Off  
Document Image Filter On (0-255)  
*Don’t Ship Histogram  
Ship Histogram  
IMGSUB2  
IMGSUB3  
IMGUSH0  
IMGUSH###  
IMGHST0  
IMGHST1  
IMGVGA1  
IMGVGA0  
DECBND1  
DECBND0  
7-8  
7-9  
7-9  
7-9  
7-9  
7-9  
Image Size Compatibility  
Intelligent Signature Capture  
Utilities  
Force VGA Resolution  
*Native Resolution  
7-10  
7-10  
7-10  
7-10  
Optimize On  
*Optimize Off  
Add Code I.D. Prefix to All Symbologies (Temporary)  
Show Decoder Revision  
PRECA2,BK2995C80!  
REV_DR  
9-1  
9-1  
9-1  
9-1  
9-1  
9-2  
9-2  
9-2  
9-2  
9-2  
9-2  
9-2  
9-4  
9-4  
Show Scan Driver Revision  
Show Software Revision  
REV_SD  
REVINF  
Show Data Format  
DFMBK3?  
TSTMNU1  
TSTMNU0  
PLGDCE1  
PLGDCE0  
PLGFOE1  
PLGFOE0  
PLGINF  
Test Menu  
On  
*Off  
Application Plug-Ins (Apps)  
*Decoding Apps On  
Decoding Apps Off  
*Formatting Apps On  
Formatting Apps Off  
List Apps  
Resetting the Factory Defaults  
Remove Custom Defaults  
Activate Defaults  
DEFOVR  
DEFALT  
10 - 22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
Maintenance  
Repairs  
Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized  
service center (see Customer Support on page 12-1).  
Inspecting Cords and Connectors  
Inspect the engine’s interface cable and connector for wear or other signs of damage. A badly worn cable or damaged connec-  
tor may interfere with engine operation. Contact your Honeywell distributor for information about cable replacement.  
Troubleshooting  
The engine automatically performs self-tests whenever you turn it on. If your engine is not functioning properly, review the fol-  
lowing Troubleshooting Guide to try to isolate the problem.  
Is the power on? Is the aimer on?  
If the aimer isn’t illuminated, check that:  
•
•
The cable is connected properly.  
The host system power is on (if external power isn’t used).  
Is the engine having trouble reading your symbols?  
If the engine isn’t reading symbols well, check that the symbols:  
•
•
•
Aren’t smeared, rough, scratched, or exhibiting voids.  
Aren’t coated with frost or water droplets on the surface.  
Are enabled in the engine or in the decoder to which the engine connects.  
Is the bar code displayed but not entered?  
The bar code is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or  
the Tab key, for example).  
•
You need to program a suffix. Programming a suffix enables the engine to output the bar code data plus the key you  
need (such as “CR”) to enter the data into your application. Refer to Prefix/Suffix Overview on page 4-1 for further  
information.  
Does the engine read the bar code incorrectly?  
If the engine reads a bar code, but the data is not displayed correctly on the host screen:  
•
The engine may not be programmed for the appropriate terminal interface.  
For example, you scan “12345” and the host displays “@es%.”  
Reprogram the engine with the correct Plug and Play bar code. See Programming the Interface beginning on page 2-1.  
•
The engine may not be programmed to output your bar code data properly.  
For example, you scan “12345” and the host displays “A12345B.”  
Reprogram the engine with the proper symbology selections. See Chapter 6.  
The engine won’t read your bar code at all.  
1. Scan the sample bar codes in the back of this manual. If the engine reads the sample bar codes, check that your bar  
code is readable.  
Verify that your bar code symbology is enabled (see Chapter 6).  
2. If the engine still can’t read the sample bar codes, scan All Symbologies On, page 6-1.  
If you aren’t sure what programming options have been set in the engine, or if you want the factory default settings restored,  
refer to Resetting the Factory Defaults on page 9-4.  
11 - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
11 - 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Customer Support  
Technical Assistance  
If you need assistance installing or troubleshooting your device, please contact us by using one of the methods below:  
Knowledge Base: www.hsmknowledgebase.com  
Our Knowledge Base provides thousands of immediate solutions. If the Knowledge Base cannot help, our Technical Support  
Portal (see below) provides an easy way to report your problem or ask your question.  
Technical Support Portal: www.hsmsupportportal.com  
The Technical Support Portal not only allows you to report your problem, but it also provides immediate solutions to your techni-  
cal issues by searching our Knowledge Base. With the Portal, you can submit and track your questions online and send and  
receive attachments.  
Web form: www.hsmcontactsupport.com  
You can contact our technical support team directly by filling out our online support form. Enter your contact details and the  
description of the question/problem.  
Telephone: www.honeywellaidc.com/locations  
For our latest contact information, please check our website at the link above.  
Product Service and Repair  
Honeywell International Inc. provides service for all of its products through service centers throughout the world. To obtain war-  
ranty or non-warranty service, please visit www.honeywellaidc.com and select Support > Contact Service and Repair to see  
your region's instructions on how to obtain a Return Material Authorization number (RMA #). You should do this prior to return-  
ing the product.  
Limited Warranty  
Honeywell International Inc. ("HII") warrants its products to be free from defects in materials and workmanship and to conform to  
HII’s published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any  
HII product which is (i) improperly installed or used; (ii) damaged by accident or negligence, including failure to follow the proper  
maintenance, service, and cleaning schedule; or (iii) damaged as a result of (A) modification or alteration by the purchaser or  
other party, (B) excessive voltage or current supplied to or drawn from the interface connections, (C) static electricity or electro-  
static discharge, (D) operation under conditions beyond the specified operating parameters, or (E) repair or service of the prod-  
uct by anyone other than HII or its authorized representatives.  
This warranty shall extend from the time of shipment for the duration published by HII for the product at the time of purchase  
("Warranty Period"). Any defective product must be returned (at purchaser’s expense) during the Warranty Period to HII factory  
or authorized service center for inspection. No product will be accepted by HII without a Return Materials Authorization, which  
may be obtained by contacting HII. In the event that the product is returned to HII or its authorized service center within the  
Warranty Period and HII determines to its satisfaction that the product is defective due to defects in materials or workmanship,  
HII, at its sole option, will either repair or replace the product without charge, except for return shipping to HII.  
EXCEPT AS MAY BE OTHERWISE PROVIDED BY APPLICABLE LAW, THE FOREGOING WARRANTY IS IN LIEU OF ALL  
OTHER COVENANTS OR WARRANTIES, EITHER EXPRESSED OR IMPLIED, ORAL OR WRITTEN, INCLUDING, WITHOUT  
LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR  
NON-INFRINGEMENT.  
HII’S RESPONSIBILITY AND PURCHASER’S EXCLUSIVE REMEDY UNDER THIS WARRANTY IS LIMITED TO THE  
REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT WITH NEW OR REFURBISHED PARTS. IN NO EVENT  
SHALL HII BE LIABLE FOR INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, AND, IN NO EVENT, SHALL ANY  
LIABILITY OF HII ARISING IN CONNECTION WITH ANY PRODUCT SOLD HEREUNDER (WHETHER SUCH LIABILITY  
ARISES FROM A CLAIM BASED ON CONTRACT, WARRANTY, TORT, OR OTHERWISE) EXCEED THE ACTUAL AMOUNT  
PAID TO HII FOR THE PRODUCT. THESE LIMITATIONS ON LIABILITY SHALL REMAIN IN FULL FORCE AND EFFECT  
12 - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
EVEN WHEN HII MAY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES, LOSSES, OR DAMAGES. SOME  
STATES, PROVINCES, OR COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CONSE-  
QUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.  
All provisions of this Limited Warranty are separate and severable, which means that if any provision is held invalid and unen-  
forceable, such determination shall not affect the validity of enforceability of the other provisions hereof. Use of any peripherals  
not provided by the manufacturer may result in damage not covered by this warranty. This includes but is not limited to: cables,  
power supplies, cradles, and docking stations. HII extends these warranties only to the first end-users of the products. These  
warranties are non-transferable.  
The duration of the limited warranty for the N56XX engine is 15 months.  
12 - 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A
Reference Charts  
Symbology Charts  
Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for AIM  
modifier character details.  
Prefix/Suffix entries for specific symbologies override the universal (All Symbologies, 99) entry.  
Refer to Data Editing beginning on page 4-1 and Data Formatting beginning on page 5-1 for information about using Code ID  
and AIM ID.  
Linear Symbologies  
AIM  
Honeywell  
Hex  
Possible modifiers  
(m)  
Symbology  
ID  
ID  
All Symbologies  
99  
61  
68  
6A  
3C  
62  
54  
69  
Codabar  
]Fm  
]H3  
]Cm  
]X0  
0-1  
a
h
j
Code 11  
Code 128  
0, 1, 2, 4  
0, 1, 3, 4, 5, 7  
Code 32 Pharmaceutical (PARAF)  
Code 39 (supports Full ASCII mode)  
TCIF Linked Code 39 (TLC39)  
Code 93 and 93i  
<
b
T
i
]Am  
]L2  
]Gm  
0-9, A-Z,  
a-m  
EAN  
]Em  
]E0  
]E3  
]E3  
]E4  
]E3  
0, 1, 3, 4  
d
d
d
d
D
D
64  
64  
64  
64  
44  
44  
EAN-13 (including Bookland EAN)  
EAN-13 with Add-On  
EAN-13 with Extended Coupon Code  
EAN-8  
EAN-8 with Add-On  
GS1  
GS1 DataBar  
]em  
]em  
]em  
]C1  
0
y
{
}
I
79  
7B  
7D  
49  
GS1 DataBar Limited  
GS1 DataBar Expanded  
GS1-128  
2 of 5  
China Post (Hong Kong 2 of 5)  
Interleaved 2 of 5  
Matrix 2 of 5  
]X0  
]Im  
Q
e
m
Y
f
51  
65  
6D  
59  
66  
66  
67  
74  
0, 1, 3  
]X0  
]X0  
]Rm  
]S0  
]Mm  
]Bm  
NEC 2 of 5  
Straight 2 of 5 IATA  
Straight 2 of 5 Industrial  
MSI  
0, 1, 3  
f
0, 1  
g
t
Telepen  
UPC  
0, 1, 2, 3, 8, 9, A, B, C  
A - 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
AIM  
Honeywell  
Hex  
Possible modifiers  
(m)  
Symbology  
ID  
ID  
UPC-A  
]E0  
]E3  
]E3  
]E0  
]E3  
]X0  
c
63  
63  
63  
45  
45  
45  
UPC-A with Add-On  
c
UPC-A with Extended Coupon Code  
c
UPC-E  
E
E
E
UPC-E with Add-On  
UPC-E1  
Add Honeywell Code ID  
Add AIM Code ID  
Add Backslash  
5C80  
5C81  
5C5C  
35  
Batch mode quantity  
5
A - 2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2D Symbologies  
AIM  
Honeywell  
Hex  
Possible modifiers  
(m)  
Symbology  
ID  
ID  
All Symbologies  
Aztec Code  
99  
7A  
48  
56  
71  
6C  
77  
]zm  
]X0  
0-9, A-C  
z
Chinese Sensible Code (Han Xin Code)  
Codablock A  
H
V
q
l
]O6  
]Om  
]Tm  
]dm  
]em  
]em  
]em  
]Um  
]Lm  
]Lm  
]Qm  
]Qm  
0, 1, 4, 5, 6  
0, 1, 4, 5, 6  
0, 1, 2, 4  
0-6  
Codablock F  
Code 49  
Data Matrix  
w
GS1  
0-3  
GS1 Composite  
GS1 DataBar Omnidirectional  
MaxiCode  
0-3  
y
y
x
r
79  
79  
78  
72  
52  
73  
73  
0-3  
0-2  
3-5  
0-6  
PDF417  
MicroPDF417  
QR Code  
R
s
s
Micro QR Code  
Postal Symbologies  
AIM  
Honeywell  
Hex  
Possible modifiers  
(m)  
Symbology  
ID  
ID  
All Symbologies  
Australian Post  
British Post  
99  
41  
42  
43  
51  
2c  
]X0  
]X0  
]X0  
]X0  
]X0  
]X0  
]X0  
]X0  
]X0  
]X0  
]X0  
]X0  
A
B
C
Q
,
Canadian Post  
China Post  
InfoMail  
Intelligent Mail Bar Code  
Japanese Post  
KIX (Netherlands) Post  
Korea Post  
M
J
4D  
4A  
4B  
3F  
4C  
4E  
50  
K
?
Planet Code  
L
Postal-4i  
N
P
Postnet  
ASCII Conversion Chart (Code Page 1252)  
In keyboard applications, ASCII Control Characters can be represented in 3 different ways, as shown below. The CTRL+X func-  
tion is OS and application dependent. The following table lists some commonly used Microsoft functionality. This table applies  
A - 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
to U.S. style keyboards. Certain characters may differ depending on your Country Code/PC regional settings.  
Non-printable  
characters  
ASCII control  
Keyboard Control + ASCII (CTRL+X) Mode  
Windows Mode Control + X Mode On (KBDCAS2)  
DEC  
HEX  
Char  
Control + X Mode Off (KBDCAS0) CTRL + X  
CTRL + X function  
0
00  
01  
02  
03  
04  
05  
06  
07  
08  
09  
0A  
0B  
NUL  
SOH  
STX  
ETX  
EOT  
ENQ  
ACK  
BEL  
BS  
Reserved  
NP Enter  
Caps Lock  
ALT Make  
ALT Break  
CTRL Make  
CTRL Break  
Enter / Ret  
(Apple Make)  
Tab  
CTRL+ @  
CTRL+ A  
CTRL+ B  
CTRL+ C  
CTRL+ D  
CTRL+ E  
CTRL+ F  
CTRL+ G  
CTRL+ H  
CTRL+ I  
1
Select all  
Bold  
2
3
Copy  
4
Bookmark  
Center  
Find  
5
6
7
8
History  
Italic  
9
HT  
10  
11  
LF  
(Apple Break)  
Tab  
CTRL+ J  
CTRL+ K  
Justify  
hyperlink  
VT  
list,  
left align  
12  
0C  
FF  
Delete  
CTRL+ L  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
127  
0D  
0E  
0F  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
1A  
1B  
1C  
1D  
1E  
1F  
7F  
CR  
Enter / Ret  
Insert  
ESC  
F11  
CTRL+ M  
CTRL+ N  
CTRL+ O  
CTRL+ P  
CTRL+ Q  
CTRL+ R  
CTRL+ S  
CTRL+ T  
CTRL+ U  
CTRL+ V  
CTRL+ W  
CTRL+ X  
CTRL+ Y  
CTRL+ Z  
CTRL+ [  
CTRL+ \  
CTRL+ ]  
CTRL+ ^  
CTRL+ -  
SO  
New  
Open  
Print  
Quit  
SI  
DLE  
DC1  
DC2  
DC3  
DC4  
NAK  
SYN  
ETB  
CAN  
EM  
Home  
PrtScn  
Backspace  
Back Tab  
F12  
Save  
F1  
Paste  
F2  
F3  
F4  
SUB  
ESC  
FS  
F5  
F6  
F7  
GS  
F8  
RS  
F9  
US  
F10  
NP Enter  
⌂
Lower ASCII Reference Table  
Note: Windows Code page 1252 and lower ASCII use the same characters.  
Printable Characters  
DEC  
HEX  
Character  
DEC  
HEX  
Character  
DEC  
HEX  
Character  
32  
33  
34  
35  
20  
21  
22  
23  
<SPACE>  
!
"
#
64  
65  
66  
67  
40  
41  
42  
43  
@
A
B
96  
97  
98  
99  
60  
61  
62  
63  
`
a
b
c
C
A - 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Printable Characters (Continued)  
DEC  
HEX  
Character  
DEC  
HEX  
Character  
DEC  
HEX  
Character  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
24  
25  
26  
27  
28  
29  
2A  
2B  
2C  
2D  
2E  
2F  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
3A  
3B  
3C  
3D  
3E  
3F  
$
%
&
'
(
)
*
+
,
-
.
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
90  
91  
92  
93  
94  
95  
44  
45  
46  
47  
48  
49  
4A  
4B  
4C  
4D  
4E  
4F  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
5A  
5B  
5C  
5D  
5E  
5F  
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
100  
101  
102  
103  
104  
105  
106  
107  
108  
109  
110  
111  
112  
113  
114  
115  
116  
117  
118  
119  
120  
121  
122  
123  
124  
125  
126  
127  
64  
65  
66  
67  
68  
69  
6A  
6B  
6C  
6D  
6E  
6F  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
7A  
7B  
7C  
7D  
7E  
7F  
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
/
0
1
2
3
4
5
6
7
8
9
:
s
t
u
v
w
x
y
z
{
|
}
~
⌂
;
<
=
>
?
\
]
^
_
Extended ASCII Characters  
Alternate Extended  
DEC  
HEX  
CP 1252  
ASCII  
PS2 Scan Code  
128  
80  
Ç
0x48  
up arrow  
down arrow  
right arrow  
↑
129  
130  
131  
81  
82  
83  
ü
é
â
0x50  
0x4B  
0x4D  
↓
→
‚
ƒ
left arrow  
←
132  
133  
134  
135  
136  
137  
138  
139  
140  
141  
142  
143  
144  
145  
146  
147  
84  
85  
86  
87  
88  
89  
8A  
8B  
8C  
8D  
8E  
8F  
90  
91  
92  
93  
„
…
†
‡
ˆ
‰
Š
‹
ä
à
å
ç
ê
ë
è
ï
Insert  
Delete  
Home  
End  
0x52  
0x53  
0x47  
0x4F  
0x49  
0x51  
0x38  
0x1D  
n/a  
Page Up  
Page Down  
Right ALT  
Right CTRL  
Reserved  
Reserved  
Numeric Keypad Enter  
Numeric Keypad /  
F1  
F2  
F3  
F4  
Œ
î
ì
n/a  
Ž
Ä
Å
É
æ
Æ
ô
0x1C  
0x35  
0x3B  
0x3C  
0x3D  
0x3E  
‘
’
“
A - 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Extended ASCII Characters (Continued)  
DEC  
HEX  
CP 1252  
ASCII  
Alternate Extended  
PS2 Scan Code  
148  
149  
150  
151  
152  
153  
154  
155  
156  
157  
158  
159  
160  
161  
162  
163  
164  
165  
166  
167  
168  
169  
170  
171  
172  
173  
174  
175  
176  
177  
178  
179  
180  
181  
182  
183  
184  
185  
186  
187  
188  
189  
190  
191  
192  
193  
194  
195  
196  
197  
198  
199  
94  
95  
96  
97  
98  
99  
”
•
ö
ò
û
ù
F5  
F6  
F7  
F8  
F9  
F10  
F11  
F12  
0x3F  
0x40  
0x41  
0x42  
0x43  
0x44  
0x57  
0x58  
0x4E  
0x4A  
0x37  
0x3A  
0x45  
0x38  
0x1D  
0x2A  
0x36  
n/a  
0x0F  
0x8F  
0x1C  
0x01  
0x36  
0xB6  
0x1D  
0x9D  
0x36  
0x1D  
–
—
˜
™
š
ÿ
Ö
Ü
¢
£
¥
₧
ƒ
á
í
ó
ú
ñ
Ñ
ª
º
¿
⌐
¬
½
¼
¡
9A  
9B  
9C  
9D  
9E  
9F  
A0  
A1  
A2  
A3  
A4  
A5  
A6  
A7  
A8  
A9  
AA  
AB  
AC  
AD  
AE  
AF  
B0  
B1  
B2  
B3  
B4  
B5  
B6  
B7  
B8  
B9  
BA  
BB  
BC  
BD  
BE  
BF  
C0  
C1  
C2  
C3  
C4  
C5  
C6  
C7  
›
œ
Numeric Keypad +  
Numeric Keypad -  
Numeric Keypad *  
Caps Lock  
Num Lock  
Left Alt  
Left Ctrl  
Left Shift  
Right Shift  
Print Screen  
Tab  
ž
Ÿ
¡
¢
£
¤
¥
¦
§
¨
©
ª
Shift Tab  
Enter  
Esc  
Alt Make  
«
¬
Alt Break  
Control Make  
Control Break  
Alt Sequence with 1 Character  
Ctrl Sequence with 1 Character  
®
¯
°
«
»
░
▒
▓
│
┤
╡
╢
╖
╕
╣
║
╗
╝
╜
╛
┐
└
┴
┬
├
─
í
²
³
´
µ
·
¸
¹
º
»
¼
½
¾
¿
À
Á
Â
Ã
Ä
Å
Æ
Ç
╞
╟
A - 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Extended ASCII Characters (Continued)  
DEC  
HEX  
CP 1252  
ASCII  
Alternate Extended  
PS2 Scan Code  
200  
201  
202  
203  
204  
205  
206  
207  
208  
209  
210  
211  
212  
213  
214  
215  
216  
217  
218  
219  
220  
221  
222  
223  
224  
225  
226  
227  
228  
229  
230  
231  
232  
233  
234  
235  
236  
237  
238  
239  
240  
241  
242  
243  
244  
245  
246  
247  
248  
249  
250  
251  
C8  
C9  
CA  
CB  
CC  
CD  
CE  
CF  
D0  
D1  
D2  
D3  
D4  
D5  
D6  
D7  
D8  
D9  
DA  
DB  
DC  
DD  
DE  
DF  
E0  
E1  
E2  
E3  
E4  
E5  
E6  
E7  
E8  
E9  
EA  
EB  
EC  
ED  
EE  
EF  
F0  
F1  
F2  
F3  
F4  
F5  
F6  
F7  
F8  
F9  
FA  
FB  
È
É
Ê
Ë
Ì
Í
Î
Ï
╚
╔
╩
╦
╠
═
╬
╧
╨
╤
╥
╙
╘
╒
╓
╫
╪
┘
┌
█
▄
▌
▐
▀
α
Ð
Ñ
Ò
Ó
Ô
Õ
Ö
×
Ø
Ù
Ú
Û
Ü
Ý
Þ
ß
à
á
â
ã
ä
å
æ
ç
è
é
ê
ë
ì
í
î
ï
ð
ñ
ò
ó
ô
õ
ö
÷
ø
ù
ú
û
ß
Γ
π
Σ
σ
µ
τ
Φ
Θ
Ω
δ
∞
φ
ε
∩
≡
≥
≤
⌠
⌡
÷
≈
°
·
·
√
A - 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Extended ASCII Characters (Continued)  
DEC  
HEX  
CP 1252  
ASCII  
Alternate Extended  
PS2 Scan Code  
252  
253  
254  
255  
FC  
FD  
FE  
FF  
ü
ý
þ
ÿ
ⁿ
²
■
ISO 2022/ISO 646 Character Replacements  
Code pages define the mapping of character codes to characters. If the data received does not display with the proper charac-  
ters, it may be because the bar code being scanned was created using a code page that is different from the one the host pro-  
gram is expecting. If this is the case, select the code page with which the bar codes were created. The data characters should  
then appear properly.  
Code Page Selection Method/Country  
Standard  
Keyboard Country  
Honeywell Code Page  
Option  
United States  
(standard ASCII)  
ISO/IEC 646-IRV  
ISO/IEC 2022  
n/a  
n/a  
n/a  
n/a  
1
Automatic National Character  
Replacement  
2 (default)  
3
Binary Code page  
Default “Automatic National Character replacement” will select the below Honeywell Code Page options for Code128, Code  
39 and Code 93.  
United States  
ISO/IEC 646-06  
ISO /IEC 646-121  
ISO /IEC 646-122  
ISO/IEC 646-14  
ISO/IEC 646-57  
ISO /IEC 646-04  
ISO /IEC 646-69  
ISO/IEC646-21  
ISO /IEC 646-CH  
ISO/IEC 646-11  
ISO /IEC 646-207  
ISO/IEC 646-08  
ISO/IEC 646-60  
ISO/IEC 646-15  
ISO/IEC 646-16  
ISO/IEC 646-17  
ISO/IEC 646-85  
0
1
Canada  
54  
18  
28  
92  
7
95  
96  
98  
99  
87  
83  
84  
86  
82  
97  
88  
94  
85  
92  
90  
91  
Canada  
Japan  
China  
Great Britain (UK)  
France  
3
Germany  
4
Switzerland  
6
Sweden / Finland (extended Annex C)  
2
Ireland  
Denmark  
Norway  
Italy  
73  
8
9
5
Portugal  
Spain  
13  
10  
51  
Spain  
A - 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Dec  
Hex  
35  
23  
36  
24  
64  
40  
91  
5B  
92  
5C  
93  
94  
5E  
96  
60  
123  
7B  
124  
7C  
125  
7D  
126  
7E  
5D  
US  
0
54  
18  
28  
92  
7
1
#
#
#
#
#
£
£
#
ù
#
#
#
£
£
#
#
#
$
$
$
$
¥
$
$
$
$
¤
$
$
$
$
$
$
$
@
à
[
â
â
[
\
ç
]
ê
ê
]
^
î
`
ô
ô
`
{
é
é
{
|
ù
ù
|
|
|
ù
ö
ö
ö
ø
ø
í
}
è
è
}
~
û
û
⎯
CA  
95  
96  
98  
99  
87  
83  
84  
86  
82  
88  
94  
97  
85  
92  
90  
91  
à
ç
É
^
^
^
^
^
î
CA  
JP  
@
@
@
à
¥
\
[
]
`
{
}
CN  
GB  
FR  
⎯
[
\
]
`
{
}
˜
¨
°
ç
§
Ü
ê
Å
Å
Å
Ú
é
Õ
¿
Ç
µ
`
é
ä
ä
ä
æ
æ
é
à
ã
°
è
ü
ü
å
å
å
ú
è
õ
ç
ç
3
§
Ä
é
Ä
Æ
Æ
É
°
Ö
ç
ß
û
ü
˜
¨
DE  
CH  
SE/FI  
DK  
NO  
IE  
4
à
ô
é
`
6
É
Ö
Ø
Ø
Í
Ü
^
^
Á
^
^
^
¿
2
@
@
Ó
§
8
`
9
ó
ù
`
á
ì
73  
5
ç
ò
ç
IT  
§
Ã
¡
Ç
Ñ
Ñ
°
PT  
13  
10  
51  
§
`
ñ
ñ
˜
¨
ES  
·
¡
`
´
ES  
ISO / IEC 646 National Character Replacements  
A - 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Unicode Key Maps  
6E  
70 71 72 73  
74 75 76 77  
78 79 7A 7B 7C 7D 7E  
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F  
10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D  
1E 1F 20 21 22 23 24 25 26 27 28 29 2B  
4B 50 55  
4C 51 56  
5A 5F 64 69  
5B 60 65  
6A  
5C 61 66  
2C 2E 2F 30 31 32 33 34 35 36 37  
39  
5D 62 67  
6C  
4F 54 59  
63 68  
3D  
3A 3B 3C  
3E 3F 38 40  
104 Key U.S. Style Keyboard  
6E  
70 71 72 73  
74 75 76 77  
78 79 7A 7B 7C 7D 7E  
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F  
10 11 12 13 14 15 16 17 18 19 1A 1B 1C  
1E 1F 20 21 22 23 24 25 26 27 28 29 2A  
4B 50 55  
4C 51 56  
5A 5F 64 69  
5B 60 65  
2B  
6A  
5C 61 66  
2C 2D 2E 2F 30 31 32 33 34 35 36 37  
39  
5D 62 67  
6C  
4F 54 59  
63 68  
3D  
3A 3B 3C  
3E 3F 38 40  
105 Key European Style Keyboard  
A - 10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sample Symbols  
UPC-A  
0 123456 7890  
Interleaved 2 of 5  
1234567890  
EAN-13  
9 780330 290951  
Code 128  
Code 128  
Code 39  
Codabar  
BC321  
A13579B  
Code 93  
123456-9$  
Code 2 of 5  
123456  
Matrix 2 of 5  
RSS-14  
6543210  
(01)00123456789012  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Sample Symbols  
PDF417  
Car Registration  
Postnet  
Code 49  
Zip Code  
1234567890  
Data Matrix  
Test Symbol  
QR Code  
Numbers  
Aztec  
MaxiCode  
Package Label  
Micro PDF417  
Test Message  
Test Message  
OCR-A with Modulo 36  
check character  
OCR-A with Modulo 10  
check character  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Programming Chart  
0
1
2
3
4
5
6
7
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Programming Chart  
A
C
E
B
D
F
Save  
Discard  
Reset  
Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or  
digits, and Save again.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Honeywell Scanning & Mobility  
9680 Old Bailes Road  
Fort Mill, SC 29707  
www.honeywellaidc.com  
N56XX-UG Rev C  
11/13  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Graco Baby Furniture 4622 User Manual
Greenheck Fan Ventilation Hood FSD 331 User Manual
Grizzly Outdoor Cart H0759 User Manual
Grundig DVR GV 470 S VPT User Manual
Haier Refrigerator 300M User Manual
Haier Refrigerator HW24WF10NG User Manual
Hoshizaki Ice Maker SRC 10H User Manual
Hotpoint Washer Dryer WMUD 943 User Manual
HP Hewlett Packard Car Video System GS917AA User Manual
HP Hewlett Packard Network Card 8990A User Manual