INSTALLATION & OPERATING
INSTRUCTIONS
MHC36 MHR36
WOODBURNING FIREPLACE
FOR MANUFACTURED HOUSING
Note: An arrow (ꢀ) found in the text signifies change in content.
WARNING!
Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this
manual. For assistance or additional information, consult a qualified installer, service agency or the gas supplier.
08/04
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
1
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
DESIGN AND INSTALLATION CONSIDERATIONS
When selecting a location for your woodburning fireplace, it is important to evaluate a number of considerations. Modern
construction techniques can create conditions that may not allow your chimney to draft properly. This may result in smoke
spillage from your fireplace, as well as cause other combustion appliances to operate incorrectly.
Tightly sealed construction is important for energy efficiency. Unfortunately, a great deal of effort has been directed to
tightening up sidewall construction, while considerably less attention has been paid to tightening upper portions of the
warm air envelope (insulated ceilings). This has increased the “Stack Effect”, a condition that increases the negative
pressure generated by the structure. This negative pressure will directly affect the drafting performance of a fireplace
chimney. To minimize the negative pressure generated by stack effect, make certain that all duct work installed in the attic
spaces is sealed airtight. Minimize the number of recessed light fixtures installed in the insulated ceiling, and use sealed
recessed light fixtures. Finally, make certain the whole house fans and attic access panels are tightly sealed. These are
important design considerations that must be observed during the design and construction stage of the home.
If you desire to put a fireplace in your basement, we recommend that you consider a direct vent gas fireplace. Basements
always have a significant negative air pressure that causes the fireplace system to be more susceptible to smoke spillage
and cold flue back drafting. Since direct vent gas fireplaces are sealed, they are not affected by the negative pressure that
exists in basements.
Finally, woodburning fireplaces perform best when their chimney (roof termination) is located on the upper half of the roof,
especially when cathedral ceilings are present. Chimneys that are located on the lower half of the roof realize what is
known as “lazy flue” and will not draft as well as a chimney that is located in the upper portion of the roof. The reason for
this is that the stack effect generated by the overall height of the living spaces inside the house will exceed the draft
generated by the chimney system. If you desire to place a woodburning fireplace in a location where the termination cap
would be located on the lower half of a roof, such as on an outside wall at the base of a cathedral ceiling, we recommend
that you consider using a direct vent gas fireplace. This will assure the homeowner a fireplace that operates correctly.
These properties do not affect just your woodburning factory built fireplace. They can cause any woodburning fireplace as
well as any conventionally vented (B-vent) gas appliance to operate improperly. Careful planning at this stage of your
project will ensure satisfaction with the operation of your fireplace once it is completed.
08/04
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
3
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
A. LISTINGS AND CODE APPROVALS
This fireplace system has been tested and listed in
Check with your local building code agency prior to installing
this fireplace to ensure compliance with local codes,
including the need for permits and follow-up inspections. If
you need assistance during installation, please contact your
local dealer or the Heatilator Technical Services
Department, Hearth & Home Technologies Inc., 1915 W.
Saunders St., Mt. Pleasant, Iowa 52641 (1-800-843-2848).
accordance with UL 127 standards, and has been listed by
Underwriters Laboratories Inc. for installation and operation
in the United States.
This fireplace has been tested and listed for use with the
optional components listed on page 5. These optional
components may be purchased separately and installed at
a later date. However, installation of an outside air kit will
require significant reconstruction, and should be installed
at the time of the initial fireplace installation.
Heatilator® is a registered trademark of Hearth & Home
Technologies Inc.
WARNING!
This fireplace and its components are designed to be installed and operated as a system. Any alteration to or
substitution for items in this system, unless allowed by these installation instructions, will void the Underwrit-
ers Laboratories listing and may void the product warranty. It may also create a hazardous installation. Read
through these instructions thoroughly before starting your installation and follow them carefully throughout
your project.
B. DESCRIPTION OF THE FIREPLACE SYSTEM
1. The Heatilator fireplace system consists of the
following:
Note: Illustrations used throughout these instructions
reflect “typical installations” and are for design purposes
a. Fireplace/Integral Grate/Outside Combustion Air
System
b. Refractory
only. Actual installation may vary slightly due to individual
design preferences. However, minimum and maximum
clearances must be maintained at all times.
c. Chimney Termination Cap
d. Chimney System
e. Hearth Extension
The illustrations and diagrams used throughout these
installation instructions are not drawn to scale.
The CP311 Convenience Pack has been designed
for the convenience of customers wishing to install a
chimney system at the 11 ft minimum straight height.
The CP313 Convenience Pack has been designed for
those wishing to install a chimney system at the 13 ft
minimum straight height.
The following combination of listed parts are included
in both the CP311 and CP313 Convenience Packs:
CP311 & CP313 Convenience Packs
Cat. #
SL324
SL336
MH842
TR344
Qty.
2
Description:
Chimney Section - 24 in. long
Chimney Section - 36 in. long
Roof Thimble and Flashing
Round Termination Cap
2
1
1
2. Optional Components Include:
a. Glass Doors
b. Fan Kit (MHC36 only)
Figure 1 - Typical Fireplace System
4
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
08/04
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
C. SYSTEM COMPONENTS
1. Fireplace Components
Catalog #
Description:
MHR36
MHC36
DM1036
Radiant Fireplace, with Integral Grate, Hearth Protection Strips and Outside Air Kit
Circulating Fireplace, with Integral Grate, Hearth Protection Strips, Fan Kit and Junction Box
Bi-fold Glass Doors - Black Finish
DM1036B Bi-fold Glass Doors - Polished Brass Finish (included with fireplace)
DM1036S Bi-fold Glass Doors - Stainless Steel Finish
DP1036
Peception Glass Doors - Black Finish
DP1036B Perception Glass Doors - Polished Brass Finish
DP1036S Perception Glass Doors - Stainless Steel Finish
FK22*
JK9*
Fan Kit (MHC36 only)
Junction Box (MHC36 only)
BC10
HX3
Fan Motor Rheostat Control (MHC36 only)
Hearth Extension
GR16
Integral Grate (included with fireplace)
Outside Air Kit (included with fireplace)
*The junction box and fan kit should be installed at the time of initial fireplace installation.
Otherwise, significant reconstruction will be required. Refer to the installation instructions included
with the JK9 and FK22 for proper installation.
Bi-Fold Glass Doors
DM1036
DM1036B
Perception Glass Doors
DP1036
DP1036B
DM1036S
DP1036S
HX3 - Hearth Extension
GR16 - Integral Grate
FK22 - Fan Kit (MHC36 only)
BC10 - Fan Motor
Rheostat Control
(MHC36 only)
08/04
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
5
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
Fireplace Dimensions
2. Chimney Components
The following pictures show only those chimney components which may be safely used with this fireplace.
Catalog #
Description:
SL306
SL312
SL318
SL324
SL336
SL348
SL315
SL330
JB877
CB876
TR344
CP311
CP313
MH841
MH842
AS8
Chimney Section - 6 in. long
Chimney Section - 12 in. long
Chimney Section - 18 in. long
Chimney Section - 24 in. long
Chimney Section - 36 in. long
Chimney Section - 48 in. long
Chimney Offset/Return - 15 deg
Chimney Offset/Return - 30 deg
Chimney Joint Band
Chimney Bracket
Round Termination Cap
Manufactured Housing Convenience Pack - 11 ft
Manufactured Housing Convenience Pack - 13 ft
Manufactured Housing 20 in. Thimble Extension
Manufactured Housing Thimble and Flashing
Attic Insulation Shield
RF370
RF371
Roof Flashing - 6/12 to 12/12 Pitch
Roof Flashing - Flat to 6/12 Pitch
6
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
08/04
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
MH841
Chimney Sections
Catalog #
SL306
SL312
SL318
SL324
SL336
SL348
A
B
6 in.
4-3/4 in.
10-3/4 in.
16-3/4 in.
22-3/4 in.
34-3/4 in.
46-3/4 in.
12 in.
18 in.
24 in.
36 in.
48 in.
MH842-Roof Thimble & Flashing
A = Actual Length
B = Effective length (length of
chimney part after it has
been snapped to another)
Firestop Spacer
Catalog #
FS338
A
B
0-deg. 14-1/2 in.
15-deg. 18-3/8 in.
FS339
FS340
30-deg.
23 in.
SL330 - Offset/Return
CB876
Chimney Bracket
TR344
Round Termination Cap
with Storm Collar
JB877-Joint Band
Outside Air Kit
AS8
Attic Insulation Shield
RF371-Roof Flashing
Flat to 6/12 Pitch
RF370-Roof Flashing
6/12 to 12/12 Pitch
08/04
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
7
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
D. PRE-INSTALLATION PREPARATION
1. Fireplace Locations and Space Requirements
Several options are available to you when choosing a location for your fireplace. This fireplace may be used as a
room divider, installed along a wall or across a corner. See Figure 2.
Locating the fireplace in a basement, near frequently opened doors, central heat outlets or returns, or other locations
of considerable air movement can affect the performance and cause intermittent smoke spillage from the front of the
fireplace. Consideration should be given to these factors before deciding on a location.
CLEARANCES!
A minimum 1 in. air clearance
must be maintained at the
back and sides of the fire-
place assembly except at the
nailing flange where the
clearance is 1/2 in.
Chimney sections at any level
require a 2 in.minimum air
space clearance between the
framing and chimney section.
Figure 2 - Fireplace Locations
WARNING!
1. Do not install in sleeping rooms.
2. Combustion air needs of a heavily fired fireplace may deplete the available oxygen supply.
CAUTION:
The structural integrity of the manufactured
housing floor, wall, ceiling and roof must be
maintained.
WARNING!
For all manufactured housing installations the outside air kit, glass door kit and MH842 manufactured
housing roof thimble and flashing kit, must be used.
8
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
08/04
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
Figures 3 and 4 show two typical installations assuming an outside air kit is being used. Therefore, an allowance must
be made for 90-deg bends. Less space is required when ducting goes directly outside without forming elbows.
These are rough framing
dimensions only.
Figure 3
Installation Along a Wall
Figure 4
Corner Installation
WARNING!
Do not draw outside air from garage spaces. Exhaust products of gasoline engines are haz-
ardous.
Do not install outside air ducts such that the air may be drawn from attic spaces, basements or
above the roofing where other heating appliances or fans and chimneys exhaust or utilize air.
These precautions will reduce the possibility of fireplace smoking or air flow reversal.
WARNING!
To prevent contact with sagging or loose insulation, the fireplace must not be installed against
vapor barriers or exposed insulation. Localized overheating could occur and a fire could re-
08/04
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
9
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
2. Frame the Fireplace
The MHR36 and MHC36 fireplaces will fit a framed opening of 39-5/8 in. wide x 33-5/8 in. tall. The finished cavity
depth must be no less than 19-3/4 in.
Figure 5 shows a typical framing (using 2 x 4 lumber) of the fireplace, assuming combustible materials are used.
All required clearances to combustibles around the fireplace must be adhered to. Chimney sections at any level
require a 2 in. minimum air space clearance between the framing and chimney section.
Note: The top header may be positioned on the hemmed
seam across the top of the fireplace assembly.
Figure 5 - Framing the Fireplace
CLEARANCES!
A minimum 1 in. air clearance must be
maintained at the back and sides of the
fireplace assembly except at the nail-
ing flange where the clearance is 1/2 in.
Chimney sections at any level require a
2 in. minimum air space clearance be-
tween the framing and chimney section.
WARNING!
Do not apply combustible finishing materials over any part of the black face of this fireplace or a structure fire
may result. The black metal fireplace front may only be covered with noncombustible materials such as ce-
ramic tile, brick, or stone. Do not cover or block any cooling air slots. Do not cover any portion of the opening
to the fireplace that would prevent the installation of an authorized glass door.
10
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
08/04
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
3. Sidewalls/Surrounds
Adjacent combustible side walls must be located a minimum of 12 in. from the fireplace opening. See Figure 6. If
you are using a decorative surround constructed of combustible material, it must be located within the shaded area
defined in Figure 6. Short stub walls are also acceptable if they are contained within the shaded area.
Figure 6 - Sidewalls and Surrounds
E. CHIMNEY REQUIREMENTS
When planning your fireplace location, the chimney construction and necessary clearances must be considered. The
fireplace system and chimney components have been tested to provide flexibility in construction. The following figures are
the minimum distances from the base of the fireplace.
1. Minimum overall straight height
2. Minimum height with offset/return
3. Maximum height
4. Maximum chimney length between an offset and return
5. Maximum distance between chimney stabilizers
6. Double offset/return minimum height
14.5 ft
14.5 ft
90 ft
20 ft
35 ft
20 ft
6 ft
7. Maximum unsupported chimney length between the offset and return
8. Maximum straight unsupported chimney height above the fireplace
25 ft
08/04
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
11
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
1. Using Offsets and Returns
a. To bypass any overhead obstructions, the chimney may be offset using a 15-deg (SL315) or 30-deg (SL330)
offset/return. Perform the following steps to determine the correct chimney component combination for your
particular installation.
b. An offset and return may be attached together or a chimney section(s) may be used between an offset and
return.
1) Measure how far the chimney needs to be shifted to enable it to avoid the overhead obstacle. See Figure 7,
dimension “A” to determine chimney sections required to achieve the needed shift.
2) After determining the offset dimension, refer to Table 1 and find the “A” dimension closest to but not less
than the distance of shift needed for your installation.
3) The “B” dimension that coincides with the “A” dimension represents the required vertical clearance that is
needed to complete the offset and return.
4) Read across the chart and find the number of chimney sections required and the model number of those
particular chimney parts.
5) Whenever the chimney penetrates a floor/ceiling, a firestop spacer must be installed.
6) The effective height of the fireplace assembly is measured from the base of fireplace to top of starter
collar. See Figure 6.
WARNING!
Do not combine offsets to create an offset greater than 30 deg from verti-
cal. This may create a fire hazard since the natural draft may be restricted.
Example: Your “A” dimension from Figure 7 is 14½”. Using
Table 1 the dimension closest to, but not less than 14½” is
145/8” using a 30° offset/return. It is then determined from the
table that you would need 33” (Dimension “B”) between the
offset and return. The chimney components that best fit your
application are two SL312s.
Figure 7 - Chimney Offset/Return
Table 1
Offset Chart*
15°
30°
A
B
A
B
SL306 SL312 SL318 SL324 SL336 SL348
1-5/8 in. 13-3/8 in. 3-7/8 in. 14-1/2 in.
2-7/8 in. 17-3/4 in. 6-1/4 in. 18-5/8 in.
4-1/8 in. 22-3/8 in. 8-5/8 in. 22-3/4 in.
4-1/2 in. 23-5/8 in. 9-1/4 in. 23-3/4 in.
5-3/4 in. 28-1/4 in. 11-5/8 in. 27-7/8 in.
6 in. 29-3/8 in. 12-1/4 in. 29 in.
7-1/4 in. 34 in. 14-5/8 in. 33 in.
7-3/4 in. 36-1/8 in. 15-1/4 in. 34-1/8 in.
8-3/4 in. 39-3/4 in. 17-5/8 in. 38-1/4 in.
-
1
2
-
-
-
-
-
-
-
-
1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1
1
-
-
1
-
-
-
-
2
-
-
-
1
1
1
-
* Proper assembly of air cooled chimney parts result in an overlap at chimney joints
of 1-1/4 in. Effective length is built into this chart.
12
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
08/04
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
2. Chimney Height Requirements (above roof
line)
a. Major building codes specify a minimum chimney
height above the roof top. These specifications
are summarized in what is known as the Ten Foot
Rule. This rule states:
“If the horizontal distance from the side of the
chimney to the peak of the roof is 10 ft or less, the
top of the chimney must be at least 2 ftabove the
peak of the roof, but never less than 3 ftin overall
height above the highest point where it passes
through the roof.
“If the horizontal distance from the side of the
chimney to the peak of the roof is more than 10 ft,
a chimney height reference point is established
on the surface of the roof a distance of 10 ftfrom
the side of the chimney in a horizontal plane. The
top of the chimney must be at least 2 ftabove this
reference point, but never less than 3 ftin height
above the highest point where it passes through
the roof.” See Figure 8.
b. These chimney heights are necessary in the
interest of safety but do not ensure smoke-free
operation. Trees, buildings, adjoining roof lines,
adverse wind conditions, etc. may create a need
for a taller chimney should smoking occur.
3. Number of Sections Required
Figure 8 - Chimney Height
To determine the chimney components needed to
complete your particular installation, follow the steps
below:
Table 2
HEIGHT OF CHIMNEY COMPONENTS
Chimney Stabilizer
a. Determine the total vertical height of the fireplace
installation. This dimension is measured from the
base of the fireplace assembly to the point where
the smoke exits the termination cap.
SL3
43/4"
Firestop Spacers
b. Subtract the effective height of the fireplace
assembly from the overall height of the fireplace
installation (measured from the base of the
fireplace to the bottom of the termination cap).
FS338
0"
0"
0"
FS339
FS340
Offsets/Returns
c. Refer to Table 2 to determine what components
must be selected to complete the fireplace
installation.
SL315
133/8"
141/2"
SL330
Roof Flashing
d. Determine the number of firestop spacers,
stabilizers, roof flashing, etc. required to
complete the fireplace installation.
RF370
0
0
RF371
Chimney Sections*
SL306
43/4"
SL312
103/4"
163/4"
223/4"
343/4"
463/4"
SL318
SL324
SL336
SL348
* Dimensions reflect effective height
08/04
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
13
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
F. FIREPLACE INSTALLATION
WARNING!
Before starting, do the following:
1. Wear gloves and safety glasses for protection.
2. Keep hand tools in good condition. Sharpen cutting edges and make sure tool handles are secure.
3. Always maintain the minimum air space required to the enclosure to prevent fire.
1. Position the Fireplace
This fireplace may be placed on either a combustible
or noncombustible continuous flat surface. Follow the
instructions for framing on pages 9-11. Slide the
fireplace into position. Be sure to provide the
minimum air clearance at the sides and back of
the fireplace assembly.
2. Place the Protective Metal Hearth Strips
Included with your fireplace you will find two metal
hearth strips measuring approximately 26 in. x 4 in.
These strips are used to provide added protection
where the fireplace and the hearth extension meet.
Slide each metal strip 2 in.under the front edge of the
fireplace. The individual pieces must overlap each
other by 1 in. minimum in the middle of the fireplace
to provide continuous coverage of the floor. See
Figure 9. These metal strips should extend from the
front and sides of the fireplace opening by 2 in.
Figure 9 - Positioning the Metal Strips
3. Level the Fireplace
Level the fireplace side-to-side and front-to-back. Shim
with noncombustible material, such as sheet metal,
as necessary. Secure the fireplace (using the nailing
flanges located on either side of the fireplace) to the
vertical framing.
Important: To ensure proper fit of the glass doors,
check the fireplace opening for square. Measure
diagonal distances of the opening to make sure
they are equal. If they are not equal, continue to
shim the fireplace until those diagonals are equal.
14
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
08/04
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
4. Assemble Chimney Sections
Attach either a straight chimney section or an offset to
the top of the fireplace (depending on your installation
requirement). Chimney sections are locked together
by pushing downward until the top section meets the
stop bead on the lower section.
The inner flue is placed to the inside of the flue section
below it. The outer casing is placed outside the outer
casing of the chimney section below it. See Figure 10.
WARNING!
Carefully follow the instructions for assembly
of the pipe and other parts needed to install this
fireplace system. Failure to do so may result in
a fire, especially if combustibles are too close
to the fireplace or chimney and air spaces are
blocked, preventing the free movement of cool-
ing air.
Figure 10
Assembling Chimney
Sections
5. Install the Firestop Spacers
Mark and cut out an opening in the ceiling for the
firestop spacer being utilized (14 1/2 in. x 14-1/2 in.
for an FS338, 14-1/2 in. x 18-3/8 in. for an FS339
and 14-1/2 in. x 23 in. for an FS340). Frame the
opening with the same dimension lumber used in
the ceiling joists.
Install the firestop spacer.
These firestop spacers are designed to provide the
minimum 2 in. air space required around the
chimney. In all situations, the firestop spacers are to
be nailed to the ceiling joists from the bottom or
fireplace side, EXCEPT when the space above is an
insulated ceiling or attic space. In this situation, the
firestop spacer must be nailed from the top side to
prevent loose insulation from falling into the
required 2 in. air space around the chimney. See
Figure 11.
CAUTION:
Firestop spacers must be used whenever the
chimney penetrates a ceiling/floor area.
Figure 11
Installing the Firestop Spacer
08/04
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
15
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
6. Attic Insulation Shield
8. Secure the Chimney System
An insulation shield should be installed when there is
a possibility of insulation coming into contact with the
factory built chimney system. The insulation shield is
installed by positioning it over the vertical chimney
section where it penetrates a firestop spacer. The
firestop spacer will support the insulation shield. See
Figure 12.
When offsets and returns are joined to straight pipe
sections, they must be locked into position with the
screws provided (outer only), using the predrilled holes.
To prevent gravity from pulling the chimney sections
apart, the returns and the chimney stabilizers have
straps for securing these parts to joists or rafters. See
Figure 13.
Note: You must provide support for the pipe dur-
ing construction and check to be sure inadvertent
loading has not dislodged the chimney section
from the fireplace or at any chimney joint.
Figure 12 - Installing an Attic Insulation Shield
7. Double-check the Chimney Assembly
Continue assembling the chimney sections up through
the firestop spacers as needed. While doing so, be
aware of the height and unsupported chimney length
limitations that are given on page 11 under “Chimney
Requirements”.
Figure 13 - Offset/Return with Stabilizer
Check each section by pulling up slightly from the top
to ensure proper engagement before installing the
succeeding sections. If they have been connected
correctly, they will not disengage when tested.
WARNING!
When chimney sections exceeding 6 ft in length
are installed between an offset and return,
structural support must be provided to reduce
off-center loading and prevent chimney sections
from separating at the chimney joints.
CAUTION:
Inner flue and outer liner sections cannot be
disassembled once locked together. Plan ahead
to ensure the proper installation height is
achieved with the selected chimney compo-
nents.
WARNING!
Maintain a minimum of 2 in. air clearance to all
parts of the chimney system at all times! Fail-
ure to maintain this 2 in. air clearance will cause
a structure fire.
16
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
08/04
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
9. MH842 Ceiling/Roof Thimble
See Figures 14 and 15.
a. Locate the point where the chimney will exit the
roof by plumbing down to the center of the
chimney. Lay out, cut and frame a 14-1/2 in. square
opening (measured on the horizontal) through the
ceiling and roof structure. See Chapter 25 of the
Uniform Building Code for roof framing details.
b. The thimble must extend completely through the
roof structure shielding combustible materials.
Five location holes have been provided to allow
for a variety of ceiling/roof thicknesses. The
thimble extension is required when the ceiling/roof
thickness exceeds 12-1/2 in. The extension
should overlap the thimble 1 in.
c. To attach the extension to the thimble, drill 1/8 in.
holes through the outer shield of the thimble using
the predrilled holes in the extension as guides.
Attach the extension to the thimble using the
screws provided with the extension.
d. Install the thimble assembly and nail it securely
to the framing members.
e. Center the flashing over the chimney and nail it to
the roof using the Stormguard nails provided. Keep
gaps between the flashing plate and the roof to a
minimum
f. Caulk the flashing plate and roof junction as well
as the vertical seam on the flashing. All nail heads
must be caulked with a roofing sealant.
Figure 14 - Ceiling/Attic Construction
Note: Roofing shingles must be below the flash-
ing plate on the lower side of a sloped roof and
over the flashing plate on the sides and top.
g. Finish assembling the chimney, storm collar and
termination cap following the installation
instructions provided with them.
Note: The closed end of
the thimble is positioned
towards the bottom.
Figure 15 - Installing an MH842
08/04
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
17
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
WARNING!
WARNING!
This fireplace has not been tested for use with
a chase above the roof. To reduce the risk of
fire, do not install a chase above the roof.
Do not pack insulation in spaces between the two shields
or above the shield inside the flashing. This may affect
temperatures to adjacent combustibles. See page 13
for minimum chimney height above roof.
WARNING!
Detailed instructions for installation of the storm collar and termination cap are packaged with these parts. To
avoid danger of fire, all instructions must be strictly followed, including the provision of air space clearance
between chimney system and enclosure. To protect against the effects of corrosion on those parts exposed to
the weather, we recommend that the chase top and termination cap be painted with a rust-resistant paint.
10. Install the Outside Air Kit
The outside air kit is supplied as a standard feature
with this fireplace and its use is required. It is
recommended to utilize the shortest duct run to
optimize the performance of the outside air kit. The
outside air kit inlet thimble should be positioned at
least 4 ft above the ground level, in a manner that will
not allow snow, leaves, etc. to block the inlet.
The outside air kit is installed on the left hand side of
the fireplace. Remove the cover plate from the side of
the fireplace assembly where the air kit is to be
installed. See Figure 16 for handle location/operation.
Figure 16 - Air Kit Handle Location
11. Termination Cap
a. Install the chimney sections up through the ceiling/
roof. When using the TR344 round termination
cap, the uppermost section of pipe must extend
6 in. above the roof to allow installation of the
storm collar and termination cap. See Figure 17.
CAUTION:
The air kit handle may get hot while burning the fire-
place. Use care when operating the handle.
b. Install the termination cap, following the
instructions provided with it.
Figure 17 - Installing a TR344 Round Termination Cap
18
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
08/04
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
12. Complete the Enclosure
Complete the fireplace enclosure, allowing space for
outside air ducts and gas piping if desired. Electrical
wiring should not come in contact with the fireplace. A
minimum clearance of 1 in. must be maintained
between the fireplace sides and the enclosure
(except at the nailing flange) as well as the fireplace
back and the enclosure. See pages 9-11 for framing
details.
Note: Use only a noncombustible material to fin-
ish the face of the fireplace below the level of the
front standoffs. A noncombustible material such as
USG MICORE CV230 Mineral Fiber Board, or USG
DUROCK Cement Board is recommended for this
purpose.
CAUTION:
When using a gas log set, the fireplace damper
must be set in the fully open position. This en-
sures proper venting of combustion products.
Figure 18 - Air Clearance Around Gas Line
13. Gas Log/Lighter Provisions
Knockouts are provided on both sides of the fireplace
to allow for connection of a certified gas log lighter or
a decorative gas appliance with a maximum input of
100,000 BTU/hour, incorporating an automatic gas
shutoff device and complying with the Standard for
Decorative Gas Appliances for Installation in
Vented Fireplaces, ANSI Z21.60. The decorative gas
appliance should be installed in accordance with the
National Fuel Gas Code, ANSI Z223.1-1980. The side
refractories are designed to allow 1/2 in. iron pipe to
pass through. Use a noncombustible sealant to seal
any opening between the gas pipe and refractory on
the inside. Repack the insulation removed to seal
around the gas pipe where it exits the side of the
fireplace. A minimum 1-1/2 in. air clearance must be
provided around the 1/2 in. iron pipe for a minimum of
4 in. beyond the fireplace. See Figure 18.
CLEARANCES!
A minimum 1 in. air clearance must be maintained
at the back and sides of the fireplace assembly ex-
cept at the nailing flange where the clearance is
1/2 in.
Chimney sections at any level require a 2 in. mini-
mum air space clearance between the framing and
chimney section.
WARNING!
This fireplace has been set up for installation of the
gas pipe on the right hand side. If it is necessary to
plumb the fireplace from the left hand side, remove
the gas cover plate and gas tube from the right hand
side of the fireplace and install on the left hand side.
Cover the hole in the right hand side outershell of the
fireplace with the cover plate that covered the gas tube.
This fireplace was not tested by the fireplace manu-
facturer for use with an unvented gas log heater. To
reduce risk of injury, do not install an unvented gas
log heater in this fireplace unless it has been spe-
cifically tested and listed by Underwriter’s Labora-
tories Inc. for use in this specific model fireplace.
Unless the unvented gas log heater is tested and
listed for use in this factory built fireplace, a fire
hazard may be created that can result in a structure
fire.
08/04
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
19
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
14. Hearth Extension
A hearth extension must be installed with all fireplaces to protect the combustible floor in front of the fireplace from
both radiant heat and sparks.
The construction of, and materials used for a hearth extension are shown in Figures 19 and 20. A hearth extension
of this construction may be covered with any noncombustible decorative material and may have a maximum thickness
as per the illustration. Seal gaps between the hearth extension and the front of the fireplace with a bead of
noncombustible sealant.
Figure 19 - Factory Built Hearth Extension
Field constructed hearth extensions should be constructed in accordance with the instructions in Figure 20. The field
constructed hearth extension must be constructed from 1/2 in. MICORE CV230, or a material with an equivalent
insulation value.
Figure 20 - Field Constructed Hearth Extension
WARNING!
Hearth extensions are to be installed only as illustrated to prevent high temperatures from occurring
on concealed combustible materials. Hearth sealing strips prevent burning or hot particles from inad-
vertently falling directly on combustible surfaces in the event the building should settle and disturb
the original construction.
20
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
08/04
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
15. Position the Hearth Extension
16. Finishing Material
Position and secure the hearth extension over the
protective metal strips that have been placed partially
under the fireplace front. These strips should be
protruding approximately 2 in. from under the fireplace
front and 2 in. on both sides of the fireplace opening.
Seal the crack between the hearth extension and
fireplace with a bead of noncombustible sealant.
See Figure 21. Apply a noncombustible finishing
material of your choice to the hearth extension.
Do not install combustible materials over the black
face of the fireplace! This poses a safety hazard
and may start a fire. You may only use noncombustible
material over the black face of the fireplace.
a. Combustible Material
Material which is made of or surfaced with wood,
compressed paper, plant fibers, plastics, or any
material capable of igniting and burning, whether
flame proofed or not, plastered or unplastered.
b. Noncombustible Material
Material which will not ignite and burn. Such
materials are those consisting entirely of steel,
iron, brick, tile, concrete, slate, glass or plasters,
or any combination thereof.
c. Noncombustible Sealant Material
Sealants which will not ignite and burn; General
Electric RTV103 Black (or equivalent), Rutland,
Inc. Fireplace Mortar #63 (or equivalent).
After completing the framing and applying the
facing material (dry wall) over the framing, a 1/2 in.
wide (maximum) bead of noncombustible sealant
must be used to close off any gaps at the top and
sides between the fireplace and facing to prevent
cold air leaks.
Only noncombustible materials may be used to
cover the black metal fireplace front.
Figure 21 - Position the Hearth Extension
17. Mantel
A combustible mantel may be positioned no lower
than 12 in. above the top of the fireplace opening.
The combustible mantel may have a maximum depth
of 12 in. Combustible trim pieces that project no more
than 1-1/2 in. from the face of the fireplace can be
placed no closer than 6 in. from the top of the fireplace
opening. Combustible trim must not cover the black
metal surfaces of the fireplace. This mantel clearance
is in accordance with Section 7-3.3.3 of ANSI/
NFPA211.
18. Glass Doors
This fireplace has been tested and listed for use with
doors as specified in Section “C. Fireplace System
Components”. Please refer to the manual packed with
each set of doors for installation instructions.
08/04
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
21
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
G. OPERATING INSTRUCTIONS
Note: Save and pass this instruction manual to subsequent home owners. The informa-
tion provided is intended to notify and warn them about making unsafe future modifica-
tions such as the addition of shelves or the use of unauthorized parts and repairs.
1. General Information
2. Outside Air
This fireplace is intended to operate as a supplemental
heat source for a single room. It is not designed to
function as a primary heat source for a structure.
A source of air (oxygen) is required in order for
combustion to take place. Whatever air is consumed
by the fire must be replaced through cracks around
windows, under doors, etc. Most newly constructed
houses or existing homes fitted with tightly sealed doors
and windows are relatively air tight. In this case, an
outside air source must be made available to feed
combustion air from outside the home.
Fireplaces, as well as other woodburning appliances,
have been used safely for many years. It has been our
experience that most problems are caused by improper
installation and operation of the fireplace. Make certain
that installation and operation of the fireplace system
is in accordance with these instructions.
A damper control handle allows the individual control
of the outside air inlet if your fireplace is equipped with
this option. Use of outside air for combustion is highly
recommended to conserve heated air within the
structure and to provide make up air to keep the
fireplace venting properly.
It is extremely important that the fire be supervised
whenever the fireplace is in use. It is also
recommended that an annual inspection be performed
on the fireplace system to determine if the flue system
needs to be cleaned, or as in the case of any appliance,
if minor repairs are required to maintain the system in
top operating condition.
This fireplace will operate correctly only if adequate
ventilation is provided to allow proper draft to the
fireplace system. Hearth & Home Technologies
assumes no responsibility for the improper
performance of the fireplace system caused by
inadequate draft due to environmental conditions, down
drafts, tight sealing construction of the structure, or
mechanical exhausting devices which create a
negative air pressure within the structure where the
fireplace is located.
This factory built fireplace is intended for use with either
solid fuel (firewood) or a decorative gas appliance that
has been tested and listed to the Standard for
Decorative Gas Appliances for Installation in
Vented Fireplaces, ANSI Z21.60. When operating
your fireplace, the flue damper must be in the open
position.
This fireplace was not tested and listed for use with an
unvented gas log heater. Do not install an unvented
gas log heater in this fireplace and operate it with the
flue damper in the closed position unless the unvented
gas log heater has been specifically tested and listed
for use in this fireplace by Underwriters Laboratories
Inc.
CAUTION:
Fireplace operation does require air. Do not take
air from other fuel burning appliances which can
result in improper venting (smoking) or air di-
lution. Always provide adequate makeup air.
Use of an unvented gas log heater in this factory
built fireplace may create a fire hazard that can
result in a structure fire.
3. Flue Damper
WARNING!
The flue damper must be in a full open position. Before
lighting the fire, verify this by looking up from the inside
of the fireplace. Always operate this fireplace with the
damper fully open. Pull the handle down to open and
push the handle up to close. Please note: down drafts,
obstructions, damaged or poor (wet) fuels can cause
smoke spillage.
DO NOT operate this fireplace with the flue
damper in the closed position. Combustion
products must vent up the chimney system to
prevent carbon monoxide poisoning, and to
prevent hot combustion gases from contacting
and overheating combustible surfaces. Failure
to operate this fireplace with the damper in the
open position may result in asphyxiation or a
structure fire.
22
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
08/04
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
4. Glass Doors
7. Wood Fuel
Most efficient fireplace operation using glass doors is
with the doors open. When the doors are open, the
screen must be closed. Only Hearth & Home
Technologies glass doors may be used. See Figure 22
for proper glass door operation.
FIREWOOD: Your fireplace performance depends on
the quality of the firewood you use. All seasoned wood,
regardless of species, contains about 8,000 BTU’s per
pound, and hardwoods have a greater density than
soft woods. Apiece of hardwood will contain about 60%
more BTU’s than an equal size piece of soft wood.
Firewood is commonly sold by the cord (128 cu. ft.). A
cord of seasoned oak (hardwood) would contain about
60% more potential energy than a cord of seasoned
pine (soft wood).
Soft woods are generally considered coniferous. These
are trees with needle-like leaves that stay green all
year and carry their seeds exposed in a cone.
Examples of soft wood trees are Douglas fir, pine,
spruce, and cedar. Soft woods require less time to dry,
burn faster and are easier to ignite than hardwoods.
Hardwoods are generally considered deciduous.
Deciduous trees are broadleaf trees that lose their
leaves in the fall. Their seeds are usually found within
a protective pod or enclosure. Some examples are oak,
maple, apple, and birch. It should be noted that there
are some deciduous trees that are not considered
hardwoods, such as poplar, aspen, and alder.
Hardwoods require more time to season, burn slower
and are usually harder to ignite than soft woods.
Figure 22
Proper Operating Positions of Bi-Fold Doors
5. Grate
The factory installed integral grate must be used to
hold the logs from falling out of an open fireplace and
to allow air to pass between the burning logs. It is
important to keep the fire off the hearth and to allow
the ashes to collect beneath the fire, thereby forming
a layer of additional heat protection.
The best wood fuel is a combination of soft wood and
hardwood. Start the fire with soft wood; the fire will give
off quick heat to bring the appliance up to operating
temperature, and then the hardwood can be added for
slow, even heat and longer burn time.
MOISTURE: Regardless of which species of wood you
burn, the single most important factor that effects the
way your fireplace operates is the amount of moisture
in the wood. The majority of the problems fireplace
owners experience are caused by trying to burn wet,
unseasoned wood.
6. Firescreen
A firescreen is always provided to control sparks. It
must be closed whenever the fireplace is in use. Glass
doors or firescreens must not be used to hold burning
material inside the fireplace. Only those glass doors
specifically tested and listed for use with the specific
fireplace model should be used. Screens should be
closed when the glass doors are closed.
Freshly cut wood can be as much water as it is wood,
having a moisture content of around 50%. Imagine a
wooden bucket that weighs about eight pounds. Fill it
with a gallon of water, put it in the fireplace and try to
burn it. This sounds ridiculous but that is exactly what
you are doing if you burn unseasoned wood.
CAUTION:
When left closed while burning your fireplace,
firescreens and glass doors will be HOT.
WARNING!
Handle with care!
Burning wet, unseasoned wood can cause ex-
cessive creosote accumulation. When ignited
it can cause a chimney fire that may result in a
serious house fire.
WARNING!
Do not store fuel within the clearances to com-
bustibles, or in the space required for refueling
and ash removal. See maintenance instructions,
“Clear Space Near the Fireplace”.
08/04
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
23
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
SEASONING: Seasoned firewood is nothing more than
Note: The first three or four fires should be of mod-
erate size to allow the oils and binders to be burned
from the fireplace and the refractory and paint to
cure. You may notice an industrial odor the first few
fires. This is considered normal.
wood that is cut to size, split and air dried to a moisture
content of around 20%. The time it takes to season
wood varies from around nine months for soft woods
to as long as eighteen months for hardwoods. The key
to seasoning wood is to be sure it has been split,
exposing the wet interior and increasing the surface
area of each piece. A tree that was cut down a year
ago and not split is likely to have almost as high a
moisture content now as it did when it was cut.
As you use the fireplace, expansion and contrac-
tion will cause minor cracking of the refractory. This
is normal, unavoidable, and will not affect the per-
formance of the fireplace. If the cracks become large
enough that the metal behind the refractory is ex-
posed or large pieces fall out, the panels should
be replaced.
The following guideline will ensure properly seasoned
wood:
a. Stack the wood to allow air to circulate freely
around and through the woodpile.
b. Elevate the woodpile off the ground to allow air
circulation underneath.
CAUTION:
Never use gasoline, gasoline-type lantern fuel,
kerosene, charcoal lighter fluid, or similar liq-
uids to start or “freshen up” a fire in this fire-
place. Keep all such liquids well away from the
fireplace.
c. The smaller the pieces, the faster the drying
process. Any piece over 6 in. in diameter should
be split.
d. Cover the top of the woodpile for protection from
rain and snow. Avoid covering the sides and ends
completely. Doing so may trap moisture from the
ground and impede air circulation.
The problems with burning wet, unseasoned wood are
twofold: First, you will receive less heat output from
wet wood because it requires energy in the form of
heat to evaporate the water trapped inside. This is
wasted energy that should be used for heating your
home. Secondly, this moisture evaporates in the form
of steam which has a cooling effect in your fireplace
and chimney system. When combined with tar and
other organic vapors from burning wood it will form
creosote which condenses in the relatively cool
fireplace and chimney.
WARNING!
Fireplaces equipped with doors should be op-
erated only with the doors fully open or fully
closed. If doors are left partially open, gas and
flame may be drawn out of the fireplace open-
ing, creating the risk of both fire and smoke.
9. Draft Problems
Note: When first lighting your fireplace, it may be
necessary to pre-warm the flue to establish a draft.
This is done by holding a rolled up piece of burn-
ing newspaper under the flue damper for a few mo-
ments. This will help reduce smoke spillage dur-
ing start-up.
8. Starting a Fire
Check the flue damper to be certain it is in the full open
position. Place crumpled or twisted paper under the
fireplace grate. Loosely arrange kindling or small
pieces of wood to form a layer above the paper.
The fires must be built on the fireplace grate, without
danger of the burning fuel falling out of the fireplace
opening.
This fireplace will operate correctly only if adequate
ventilation is provided to allow proper draft to the
fireplace system. Hearth & Home Technologies
assumes no responsibility for the improper
performance of the fireplace system caused by
inadequate draft due to environmental conditions, down
drafts, tight sealing construction of the structure, or
mechanical exhausting devices which will create a
negative air pressure within the structure where the
fireplace is located.
Light the paper and add small pieces of wood until a
hot bed of embers has been established.
After establishing the fire bed, and the small firewood
is burning briskly, add a minimum of three average
sized pieces of split firewood, place the wood in such
a manner to allow combustion air and flames between
them.
24
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
08/04
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
Flue draft is measured as negative pressure in the
chimney. The amount of negative pressure determines
how strong the draft is. The draft is important because
it draws the combustion air into the fireplace and pulls
the smoke out of the chimney. There are three basic
criteria essential in establishing and maintaining flue
draft:
If the fire is hard to start and smoke spills out of the
fireplace, or you find it difficult to establish and maintain
a moderately high burn rate, then the flue draft is too
low and corrective measures must be taken.
Be sure you have air available for combustion and that
your firewood is dry and well seasoned. Build your fires
properly and according to the instructions given in
operating instructions, “Starting a Fire”. Be sure your
flue system is installed correctly and that it is the proper
diameter and height. Check for the following:
•
•
•
Availability of combustion air.
Heat generated from the fire.
Diameter and height of the flue system.
These three factors work together as a system to create
the flue draft. Increasing or decreasing any one of them
will affect the other two and thus change the amount
of draft in the entire system. See Figure 23.
•
All chimney sections are properly installed and the
joints are tightly sealed.
•
•
The chimney is clean and free of creosote buildup.
Make sure overhanging trees and branches are
cut back within ten feet of the top of the chimney.
Ensure the chimney cap is clean and free of any
buildup of soot or creosote.
•
If you still suspect you have a low draft problem it may
be necessary to increase the volume of air in your flue
system. Since the diameter of your flue system is
matched with the size of the flue collar and should not
be changed, then the height of the system must be
increased. Add chimney sections a little at a time until
the draft improves.
In some cases, regardless of what you do, it can still
be difficult to establish the proper flue draft. This is
especially evident when using an exterior factory built
chimney or exterior masonry chimney. Try placing
several sheets of crumpled paper on top of your kindling
as close to the flue outlet of the fireplace as possible.
Light this paper first then the paper under the kindling.
The heat generated from the rapidly burning paper on
top of the kindling should help get the draft established.
Still other factors can affect how well your flue system
performs. Neighboring structures, high winds, tall trees,
even hillsides can affect air currents around the
chimney. Well designed chimney caps are available
that can help. Your fireplace dealer is the local expert
in your area. He or she can usually make suggestions
or discover problems that can be easily corrected
allowing your fireplace to operate correctly as it has
been designed, providing safe and economical heat
for your home.
Figure 23 - Flue Draft
08/04
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
25
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
H. MAINTENANCE INSTRUCTIONS
1. Disposal of Ashes
Ashes should be placed in a metal container with a
tight-fitting lid. The closed container of ashes should
be placed on a noncombustible floor or on the ground,
well away from all combustible materials, pending final
disposal. If the ashes are disposed of by burial in soil
or otherwise locally dispersed, they should be retained
in the closed container until all embers have thoroughly
cooled.
WARNING!
A chimney fire can permanently damage your
chimney system. This damage can only be re-
paired by replacing the damaged component
parts. Chimney fires are not covered by the Lim-
ited Warranty and Buyer Protection Plan.
2. Creosote and Soot
Inspect the chimney internally for obstructions and
construction damage. Flue pipe joints and seams must
be continuous and mechanical tight. In a used chimney,
additional inspection is needed for creosote buildup,
which is the formation of a flammable sediment.
When wood is burned slowly, it produces tar and other
organic vapors, which combine with expelled moisture
to form creosote. The creosote vapors condense in
the relatively cool chimney flue of a slow-burning fire.
As a result, creosote residue accumulates on the flue
lining. When ignited, this creosote makes an extremely
hot fire.
The chimney should be inspected at least twice a year
during the heating season to determine if creosote
buildup has occurred.
Figure 24
Chimney & Termination Cap Cleaning
If creosote has accumulated, it should be removed
to reduce the risk of a chimney fire.
3. Chimney Cleaning
If you do detect a buildup of creosote, contact a
qualified chimney sweep or clean it yourself. To do this,
perform the following steps:
a. Open the damper.
b. Hang a damp sheet across the fireplace opening
to stop dirt and soot from entering the room.
c. Remove the termination cap or housing top. See
Figure 24.
d. Clean with a stiff nylon brush attached to a pole
OR tie a small burlap bag filled with straw and
several small stones or sand. Work up and down
the flue until the flue is clean.
e. Replace the termination cap or housing top.
4. Clear Space Near the Fireplace
Combustible materials must not be stored on the hearth
extension. Room furnishings such as drapes, curtains,
chairs, or other combustibles must be at least four feet
from the open front of the fireplace.
26
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
08/04
MHC36 AND MHR36 INSTALLATION INSTRUCTIONS
INDEX
A
P
Air Clearance 16, 19
Air Kit 7, 18
Air Kit Handle Location 18
Ashes, Disposal of 26
Attic Insulation Shield 16
Firewood 22, 23
Flashing 17
Flue 22
Framing 10
Fuel 22, 23
Positioning 14
Pre-Installation Preparation 8
R
Roof Flashing 7, 17
Roof Thimble 7, 17
B
G
S
Building Codes 4, 13, 17, 21
Gas Codes 19, 22
Gas Knockout Location 6
Gas Log/Lighter Provisions 19
General Information 22
Glass Doors 5, 21, 23
Grate 5, 23
Safety 14
C
Seasoning the Wood 24
Sidewalls/Surrounds 11
Smoke 9
Chimney
Checking the Assembly 16
Cleaning 26
Creosote 26
Soot 26
Space Requirements 8
Standard for Decorative Gas Appli-
ances 19, 22
Starting a Fire 24
Surrounds 11
H
Height Requirements 13
Requirements 11
Securing the System 16
Chimney Bracket 7
Chimney Sections
Assembling 15
Number Required 13
Codes 4
Building 4, 13, 17, 21
Gas 19, 22
Combustible
Material 20
Combustible Material 21
Components 5
Construction 20
Creosote 26
Hearth Extension 20
Positioning 21
I
T
Installation
Along a Wall 9
In a Corner 9
Insulation Shield 16
Ten Foot Rule 13
Termination Cap 7, 18
Typical Fireplace System 4
J
U
Joint Band 7
UL 127 Standards 4
Unvented Gas Log Heater 19, 22
L
V
Leveling the Fireplace 14
Locations 8
Ventilation 24
D
M
W
Damper 22
Description of the Fireplace System 4
Dimensions 6
Doors 5, 21, 23
Draft 24
Mantel 11, 21
Wet Insulation 2
Wood
Moisture of 22, 23
Seasoning of 24
Wood Fuel 22, 23
Material, Sealant 21
Metal Hearth Strips 14
MH842 7
Moisture Content of Wood 22, 23
E
N
Exhaust Products 9
Negative Air Pressure 24
Noncombustible Material 21
Noncombustible Sealant Material 21
F
Fan Kit 5
Finishing 21
Fireplace
O
Enclosure 19
Locations 8
Firescreen 23
Firestop Spacer
Installation 15
Offsets/Returns 7, 12
Outside Air 22
Outside Air Kit 7, 18
Overhead Obstructions 12
08/04
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
27
HEATILATOR WOODBURNING FIREPLACE
Limited Warranty
As part of its
20-YEAR BUYER PROTECTION PROGRAM
AS PART OF ITS 20 YEAR BUYER PROTECTION PROGRAM (“PROGRAM”), HEARTH & HOME TECHNOLOGIES INC.
(“HHT”) is pleased to offer a Limited Warranty and a Replacement Parts Advantage covering specific components of your Heatilator
woodburning fireplace system ( the “Fireplace”), installed in the United States of America or Canada. Dealers and employees of HHT have no
authority to make any warranty or authorize any remedies in addition to or inconsistent with the terms of this Program.
Limited Warranty
HHT warrants the following components of your Heatilator woodburning fireplace to be free from original defects in material and workmanship
during the applicable periods described: five years for the firebox assembly, chimney system and roof termination; two years for refractory
firebox liners; and one year for the grate, wire mesh screens, fan system, outside air system, and glass doors. All limited warranty periods run
from the date of initial installation of your Fireplace (the “Installation Date”). The Limited Warranty is subject to the conditions, exclusions and
limitations of liability listed below.
Replacement Parts Advantage
Under HHT’s Replacement Parts Advantage, for a period of twenty years from your Installation Date of your Fireplace, if available, HHT will
provide you with repair or replacement parts for defective components which are no longer under their applicable Limited Warranty, at 50% of
the then current retail list price for such components. HHT shall have no responsibility for freight and labor charges related to such parts.
Conditions, Exclusions, & Limitations of Liability
A. Both the Limited Warranty and Replacement Parts Advantage supplied by HHT apply only while the Fireplace is in its location of
original installation. HHT’s obligation under this warranty does not extend to damages resulting from (1) installation, operation or
maintenance of the Fireplace not in accordance with the Installation Instructions, Operating Instructions, and the Listing Agent Identification
Label furnished with the Appliance; (2) installation which does not comply with local building codes; (3) shipping, improper handling,
improper operation, abuse, misuse, accident or unworkmanlike repairs; (4) environmental conditions, inadequate ventilation or drafting
caused by tight sealing construction of the structure, air handling devices such as exhaust fans or forced air furnaces, or other causes;
(5) use of fuels other than those specified in the Operating Instructions; (6) installation or use of components not supplied with the
Fireplace or any other components not expressly authorized and approved by HHT; and/or (7) modification of the Fireplace not expressly
authorized and approved by HHT in writing. This warranty is limited to only the component parts manufactured or supplied by HHT.
B. During the first year of the Limited Warranty, HHT will, at its sole option, repair or replace any covered defective component and will
provide replacement parts at no charge. And will pay reasonable labor and freight costs. During the second through the fifth years of the
Limited Warranty (if applicable), HHT will provide replacement parts free of charge for any covered defective component, but will not pay
for freight or labor costs related to the shipment of the parts or the actual repair or replacement. After the fifth anniversary of the
Installation date, HHT’s sole obligation and your exclusive remedy is set forth in HHT’s Replacement Parts Advantage described above.
In no event shall HHT be liable for any incidental or consequential damages caused by defects in your Fireplace.
C. EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE WARRANTY SPECIFIED
ABOVE.
D. Some states do not allow exclusions or limitations of incidental or consequential damages, so those limitations may not apply to
you. This warranty gives you specific rights; you may also have other rights which vary from state to state.
How to Obtain Service
1. To obtain service under this warranty you must:
2. Send written notice of the claimed condition to Heatilator Technical Service Department, Hearth & Home Technologies, 1915 W.
Saunders Street, Mt. Pleasant, Iowa 52641-1563. You may also register your claim online at www.heatilator.com/contact.asp.
3. Provide proof of purchase, model number, serial number, and manufacturing date code to HHT.
4. Provide HHT reasonable opportunity to investigate the claim, including reasonable opportunity to inspect the Appliance prior to any
repair or replacement work and before the Appliance or any component of the Appliance has been removed from the place of original
installation.
5. Obtain HHT’s consent to any warranty work before the work is done.
ADDITIONAL INFORMATION: If you would like information on current HEATILATOR products or want to locate a dealer in your area, call
1-800-843-2848.
2003 Heatilator is a Registered Trademark of Hearth & Home Technologies Inc.
28
31072 Rev G
Download from Www.Somanuals.com. All Manuals Search And Download.
08/04
|