¨
Model No. 831.297970
Serial No.
Find the serial number in the location
shown below. Write the serial number
in the space above for reference.
Serial Number Decal
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
USER'S MANUAL
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
surge suppressor (TVSS). The surge sup-
pressor must have a UL suppressed voltage
rating of 400 volts or less and a minimum
surge dissipation of 450 joules. The surge
suppressor must be electrically rated for 120
volts AC and 15 amps.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with
eight feet of clearance behind it. Do not place
the treadmill on any surface that blocks air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
12. Keep the power cord and the surge suppres-
sor away from heated surfaces.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See BE-
FORE YOU BEGIN on page 5 if the treadmill
is not working properly.)
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or oxygen is administered.
14. Never start the treadmill while you are stand-
ing on the walking belt.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
15. Always hold the handrails when walking or
running on the treadmill.
7. The treadmill should not be used by persons
weighing more than 250 pounds. Never allow
more than one person at a time on the tread-
mill.
16. The treadmill is capable of high speeds; ad-
just the speed in small increments to avoid
sudden jumps in speed.
17. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the on/off switch to
the off position when the treadmill is not in
use. (See the drawing on page 5 for the loca-
tion of the on/off switch.)
8. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose
clothing that could become caught in the
treadmill. Athletic support clothes are recom-
mended for both men and women.
9. Always wear athletic shoes when using the
treadmillÑnever use the treadmill with bare
feet, wearing only stockings, or in sandals.
For maximum walking belt life, never use
shoes with heavy treads.
18. Never drop or insert any object into any
opening.
19. When operating the treadmill, keep hands
and feet from underneath the treadmill.
10. When connecting the power cord (see page
9), plug the power cord into a surge suppres-
sor (not included) and plug the surge sup-
pressor into a grounded circuit capable of
carrying 15 or more amps. No other appli-
ance should be on the same circuit. Do not
use an extension cord.
20. You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
21. When folding or moving the treadmill, make
sure that the storage latch is fully engaged.
22. Inspect and tighten all parts of the treadmill
every three months.
11. Use only a single-outlet surge suppressor
that is UL 1449 listed as a transient voltage
3
Download from Www.Somanuals.com. All Manuals Search And Download.
other than the procedures in this manual
should be performed by an authorized ser-
vice representative only.
23.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
24. The treadmill is intended for in-home use
only. Do not use the treadmill in any
commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. SEARS assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown at the right and below have been placed
on your treadmill. If a decal is missing, or if it is not legi-
ble, please call our toll-free HELPLINE to order a free re-
placement decal (see the back cover of this manual).
Apply the decal in the location shown.
IMPORTANT:
Incline must be set at lowest
level before folding treadmill
into storage position.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for purchasing the SOFTSTRIDER
S200ª treadmill by HealthRider. The SOFTSTRIDER
S200 offers an impressive array of features that will
help you to achieve your fitness goals in the conve-
nience of your home. From the advanced console to
the ultra-soft walking belt, the SOFTSTRIDER S200 is
designed to make each workout more effective and
enjoyable. And when youÕre not exercising, the SOFT-
STRIDER S200 can be folded away, taking less than
half the space of conventional treadmills.
additional questions, please call our toll-free
HELPLINE at 1-800-736-6879, Monday through
Saturday, 7 a.m. until 7 p.m. Central Time (excluding
holidays). To help us assist you, please note the prod-
uct model number and serial number before calling.
The model number of the treadmill is 831.297970. The
serial number can be found on a decal attached to the
treadmill (see the front cover of this manual for the lo-
cation).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
For your benefit, read this manual carefully before
using the SOFTSTRIDER S200 treadmill. If you have
Accessory Tray
Book Holder
Console
Water Bottle Holder*
Storage Latch
Handrail
Key/Clip
On/Off
Switch
Circuit
Breaker
Cushioned Walking Belt for
maximum exercise comfort
Foot Rail
BACK
Power
Cord
RIGHT SIDE
Rear Roller
Adjustment Bolts
*Water bottle is not included
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING UP THE TREADMILL
Set-up requires two people. Place the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until the treadmill is set up. No tools are required.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
1. With the help of a second person, carefully raise the
Uprights (82) until the Front Wheels (77) are resting on
the floor as shown.
1
82
77
2. Remove the paper backing from the Wrench Clip (71).
Press the Wrench Clip onto the Frame (92) in the indi-
cated location. Press the Allen Wrench (72) into the
Wrench Clip. Note: The use of the Allen Wrench is
described on pages 16 and 17.
2
92
71
72
3. Make sure that all parts are tightened before you use the treadmill. Place a mat beneath the treadmill
to protect the floor or carpet. For your benefit, we recommend that you familiarize yourself with the
ÒTROUBLE-SHOOTING AND MAINTENANCEÓ section on pages 16 and 17 before using the treadmill.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
1
HOW TO PLUG IN THE POWER CORD
Grounded Outlet Box
Surge Suppressor
Grounding Pin
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the productÑif it will
not fit the outlet, have a proper outlet
Grounding Pin
Grounded Outlet
Grounding Plug
installed by a qualified electrician.
2
Grounded Outlet Box
Adapter
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeÕs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right).
Surge Suppressor
Lug
Metal Screw
Surge suppressors are sold at most hardware stores
and department stores. Use only a single-outlet surge
suppressor that is UL 1449 listed as a transient voltage
surge suppressor (TVSS). The surge suppressor must
have a UL suppressed voltage rating of 400 volts or
less and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE OPERATION
I
C
K
L
B
J
M
A
D
E
F
G
N
O
Note: If there is a thin sheet of clear plastic
on the face of the console, remove it.
H
FEATURES OF THE CONSOLE
CAUTION:Before operating the
console, read the following precautions.
The advanced console offers a selection of features
designed to make your workouts more enjoyable and
effective. When the console is in the manual mode, the
speed and incline of the treadmill can be changed with
a touch of a button. As you exercise, the LED displays
will provide continuous exercise feedback. The con-
sole also offers five preset workout programs. Three
programs automatically control the speed of the tread-
mill and two programs automatically control the incline
of the treadmill as they guide you through effective
workouts.
¥ Do not stand on the walking belt when turn-
ing on the power or starting the walking belt.
¥ Always wear the clip (see H above) while
operating the treadmill. If the key is pulled
from the console, the walking belt will stop.
¥ The treadmill is capable of high speeds;
adjust the speed in small increments.
An optional pulse sensor adds even more features to
the console. The pulse sensor mounts in front of the
console, allowing you to measure your heart rate at
any time as you exercise. To purchase the optional
pulse sensor, refer to page 13.
¥ To reduce the risk of electric shock, keep the
console dry. Avoid spilling liquid on the
console and use only a sealable water bottle.
Note: The console can display speed and distance
in either miles or kilometers (see page 11). For
convenience, all instructions in this section refer
to miles.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
M.Program ProfilesÑThese profiles show how the
speed or incline of the treadmill will change during
workout programs. During the Speed 1 program, for
example, the speed will gradually increase during
the first half of the program, and then gradually
decrease during the last half.
DIAGRAM OF THE CONSOLE
Refer to the drawing at the top of page 8.
A. Water Bottle HolderÑKeeps your water bottle
handy during your workouts.
N. SELECT ButtonsÑThese buttons are used to select
the manual mode and the workout programs.
B. Accessory TrayÑHolds your personal items.
O. ENTER ButtonÑThis button is used to enter selec-
tions.
C. Reading RackÑAllows you to enjoy your favorite
magazine or read a book while you get in shape.
D. INCLINE ButtonsÑThese buttons control the incline
of the treadmill. Each time a button is pressed, the
incline will change by 0.5%. The incline range is 3%
to 10%.
HOW TO TURN ON THE POWER
E. PAUSE/STOP ButtonÑThis button stops the
walking belt. When the button is pressed, the TIME,
DISTANCE/INCLINE and CALORIES/PULSE
displays will pause. If the button is held down for
two seconds, the displays will be reset.
Make sure that the
on/off switch, located
on the front of the
treadmill, is in the on
position.
On
F. START ButtonÑThis button starts the walking belt.
G. SPEED ButtonsÑThese buttons control the speed
of the walking belt. Each time a button is pressed,
the speed will change by 0.1 mph. The speed range
is 0.5 mph to 10 mph.
Next, make sure that the power cord is properly plugged
in (see page 7). Note: If the key is in the console when
the power cord is plugged in, the letters ÒPOÓ will flash in
the CALORIES/PULSE display. If this occurs, remove
the key.
H. Key with ClipÑThe key turns the console on and
off. The attached clip is designed to be worn on
your waistband. If the key is pulled from the
console, the power will automatically turn off.
Step onto the foot rails of the
treadmill. Find the clip
attached to the key, and slide
the clip onto the waistband of
your clothing. Next, insert the
key fully into the console.
The MANUAL indicator will begin to flash; all other indi-
cators and displays will remain dark.
I. Operating InstructionsÑThese instructions list the
basic steps of console operation.
J. LED DisplaysÑThese displays provide continuous
feedback of the elapsed time, speed, distance,
incline and the number of calories you have burned.
The lower display also shows your heart rate when
an optional pulse sensor is used.
K. Heart Rate TableÑThis table lists recommended
heart rates for fat burning and aerobic exercise (see
CONDITIONING GUIDELINES on page 18.
L. MANUAL/Program IndicatorsÑThese indicators
show when the manual mode is selected and when
one of the workout programs is selected.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Press the START button or the SPEED + button.
HOW TO USE THE MANUAL MODE
Insert the key into the console.
5
A moment after the button is pressed, the walking
belt will begin to move at 1.0 mph. Hold the hand-
rails and begin walking. As you exercise, change
the speed of the walking belt as desired with the
SPEED buttons. Each
time a button is pressed,
the speed will change
by 0.1 mph. The speed
range of the walking belt
is 0.5 mph to 10.0 mph.
1
See HOW TO TURN ON THE POWER on page 9.
Note: When you are familiar with the console,
you may go directly to step 5. While learning to
use the console, please read all steps.
Select the MANUAL mode.
2
3
When the key is inserted,
the MANUAL indicator
will begin to flash. (Note:
If a program has been
selected, hold down the
PAUSE/STOP button for
two seconds until the MANUAL indicator is flashing.)
To select the manual mode, press the ENTER
button while the MANUAL indicator is flashing.
To stop the walking belt for a moment, press the
PAUSE/STOP button. The displays will pause and
the TIME display will begin to flash. To restart the
walking belt, press the START button or the
SPEED
+
button. Note: To stop the walking belt
and reset all displays, hold down the PAUSE/STOP
button for two seconds. The console will then be in
the same state as if the key had just been inserted.
Note: When one of the SPEED buttons is pressed,
the SPEED display will show the selected speed
setting for seven seconds. The display will then
show the actual speed of the walking belt.
Enter your weight if desired.
When the manual mode
is selected, the TIME
display will light and a
weight setting will begin
to flash in the CALO-
RIES/PULSE display. If
Adjust the incline as desired.
6
To vary the intensity of
your exercise, the in-
you enter your weight into the console, the CALO-
RIES/PULSE display will be more accurate.
cline of the treadmill can
be changed with the
INCLINE buttons. Each
time a button is pressed,
If you do not want to enter your weight, press the
ENTER button. To enter your weight, press the
SELECT buttons. Each time a button is pressed,
the weight setting will change by 1 pound. If a but-
ton is held down, the weight setting will change in
increments of 5 pounds. When the correct weight
is shown, press the ENTER button. Once your
weight is entered, it will be saved in memory.
the incline will change by 0.5%. The incline range
is 3% to 10%. Note: When one of the INCLINE
buttons is pressed, the DISTANCE/INCLINE
display will show the incline setting for seven
seconds. After the INCLINE buttons are pressed, it
may take a moment for the treadmill to reach the
selected incline setting.
Enter your age if desired.
Follow your progress with the LED displays.
4
7
After a weight setting is
entered, an age setting
will begin to flash in the
SPEED display.
TIME displayÑThis
display shows the total
time that the walking
belt has been moving.
Note: When a workout
program is selected, this
display will show the time remaining in the program.
If you do not want to
enter your age, press the ENTER button. If you
want to enter your age, press the SELECT but-
tons. Each time a button is pressed, the age set-
ting will change by 1 year. If a button is held down,
the age setting will change in increments of 5
years. When the correct age is shown, press the
ENTER button. Once your age is entered, it will be
saved in memory.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEED displayÑThis
display shows the speed
of the walking belt, in
miles per hour or kilome-
ters per hour.
HOW TO USE THE SPEED PROGRAMS AND
THE INCLINE PROGRAMS
The Speed 1, Speed 2 and Speed 3 programs automat-
ically control the speed of the treadmill as they guide
you through effective workouts; the Incline 1 and Incline
2 programs automatically control the incline of the
treadmill.
How to select miles per
hour and kilometers
per hour: Hold down the
PAUSE/STOP button
while inserting the key
into the console. An ÒEÓ
(for english miles) or an ÒMÓ (for metric kilometers)
will appear in the SPEED display. Press the SPEED
+ button to change the unit of measurement.
Remove and then reinsert the key.
Follow the steps below to use a Speed program or an
Incline program.
Insert the key fully into the console.
1
See HOW TO TURN ON THE POWER on page 9.
DISTANCE/INCLINE
displayÑThis display
shows the distance that
the walking belt has
moved and the incline
level of the treadmill.
Every seven seconds, the display will change from
one number to the other. The INCLINE indicator
will light when the incline is shown. Note: If the
speed is shown in mph, the distance will be shown
in miles; if the speed is shown in kph, the distance
will be shown in kilometers.
Select the desired program.
2
To select a program,
the MANUAL indicator
or a program indicator
must be flashing. If
necessary, hold down
the PAUSE/STOP but-
Indicator
ton for two seconds until
the MANUAL indicator is
flashing. Next, press
the SELECT + or Ð
Program
CALORIES/PULSE
displayÑThis display
shows the number of
calories you have
burned.
button repeatedly until the Speed 1, Speed 2,
Speed 3, Incline 1 or Incline 2 program indicator is
flashing. Then, press the ENTER button. A profile
of the program you have selected will appear in the
program display.
Note: If an optional pulse sensor is used, the
CALORIES/PULSE display will show both the
number of calories you have burned and your
heart rate. Every seven seconds, the display will
change from one number to the other. The PULSE
indicator will light when your heart rate is shown.
Note: When you are familiar with the console,
you may go directly to step 6. While learning to
use the console, please read all steps.
Enter your weight if desired.
3
When a program is
selected, a weight
setting will begin to flash
in the CALORIES/
When you are finished exercising, stop the
walking belt and remove the key.
8
Step onto the foot rails and press the PAUSE/STOP
button. Next, change the incline of the treadmill to
3%. The incline must be at 3% when the tread-
mill is folded to the storage position or the
treadmill will be damaged. Remove the key from
the console and put it in a secure place. Move the
on/off switch to the off position (see page 9).
PULSE display. If your
weight is entered into
the console, the CALORIES/PULSE display will be
more accurate.
If you do not want to enter your weight, or if you
have already entered your weight, press the
ENTER button. If you want to enter your weight,
press the SELECT buttons. When the correct
weight is shown, press the ENTER button.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEED buttons. To stop the program for a mo-
ment, press the PAUSE/STOP button. The dis-
plays will pause and the TIME display will begin to
flash. To restart the program, press the START
Enter your age if desired.
4
5
See step 4 on page 10.
button or the SPEED
+
button. To end the program
Adjust the maximum incline or speed setting.
at any time, hold down the PAUSE/STOP button
for two seconds. The console will then be in the
same state as if the key had just been inserted.
If you selected the
Speed 1, Speed 2 or
Speed 3 program: After
an age setting is entered,
a number will begin to
flash in the SPEED dis-
play. This number shows the maximum speed that
the walking belt will reach during the program. The
maximum speed setting can be from 4 mph to 10
mph. If you want to change the maximum speed
setting, press the SELECT buttons. Then, press
the ENTER button.
If you selected the Incline 1 or Incline 2 pro-
gram: A moment after the START button or the
SPEED + button is pressed, the walking belt will
begin to move and the treadmill will adjust to the
first incline setting of the program (unless it is al-
ready at the first incline setting). Hold the handrails
and begin walking. During the program, the incline
of the treadmill will periodically change as shown
by the program profile on the console. The speed
of the walking belt can be changed as desired dur-
ing the program with the SPEED buttons.
If you selected the
Incline 1 or Incline 2
The TIME display will show the time remaining in
the program. When no time remains, the walking
belt will slow to a stop and the program will be
completed.
program: After an age
setting is entered, a
number will begin to flash
in the DISTANCE/
INCLINE display. This number shows the maximum
incline that the treadmill will reach during the pro-
gram. The maximum incline setting can be from 5%
to 10%. If you want to adjust the maximum incline
setting, press the SELECT buttons. Then, press the
ENTER button.
Note: If the program is too easy or too difficult, the
current incline setting can be adjusted with the IN-
CLINE buttons. To stop the program for a moment,
press the PAUSE/STOP button. The displays will
pause and the TIME display will begin to flash. To
restart the program, press the START button or
the SPEED
+
button. To end the program at any
Press the START button or the SPEED + button
6
time, hold down the PAUSE/STOP button for two
seconds. The console will then be in the same
state as if the key had just been inserted.
If you selected the Speed 1, Speed 2 or Speed 3
program: A moment after the START button or the
SPEED + button is pressed, the walking belt will
begin to move. Hold the handrails and begin walk-
ing. During the program, the speed of the walking
belt will periodically change as shown by the pro-
gram profile on the console. The incline of the
treadmill can be changed as desired during the
program with the INCLINE buttons.
Follow your progress with the LED displays.
7
8
See step 7 on page 10.
When you are finished exercising, remove the
key.
Make sure that the incline of the treadmill is at 3%.
The incline must be at 3% when the treadmill is
folded to the storage position or the treadmill
will be damaged. Remove the key from the con-
sole and put it in a secure place. In addition, move
the on/off switch to the off position (see page 9).
The TIME display will show the time remaining in
the program. When no time remains, the walking
belt will slow to a stop and the program will be
completed.
Note: If the program is too easy or too difficult, the
current speed setting can be adjusted with the
12
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE
THE OPTIONAL PULSE SENSORS
The console features an information mode that keeps
track of the total time and distance accumulated on the
treadmill. The information mode also allows you to
switch the console from miles per hour to kilometers
per hour.
Two optional pulse sensors add even more features to
the console. To purchase one of the pulse sensors,
refer to the card accompanying the treadmill.
An optional hand
pulse sensor mounts
to the handlebar in
front of the console,
To select the information mode, hold down the
PAUSE/STOP button while inserting the key into the
console. When the information mode is selected, the
following information will be shown:
Pulse
Sensor
allowing you to mea-
sure your heart rate
at any time during
your workouts.
The TIME display will show
the total number of hours
that the treadmill has been
used.
An optional chest pulse sensor can be worn during
your workouts, for hands-free heart rate monitoring.
The SPEED display will show
an ÒEÓ (for english miles) or an
ÒMÓ (for metric kilometers). To
change the unit of measure-
ment, press the SPEED +
button.
Chest Pulse Sensor
The DISTANCE/INCLINE dis-
play will show the total number
of miles that the walking belt
has moved.
To exit the information mode, remove the key from the
console.
Note: The hand pulse sensor and the chest pulse sen-
sor cannot be used simultaneously.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
Caution: You must be able to safely lift 45 pounds (20
kg) in order to raise, lower, or move the treadmill.
1. Hold the treadmill in the locations shown at the right. To
decrease the possibility of injury, bend your legs and
keep your back straight. As you raise the treadmill,
make sure to lift with your legs rather than your back.
Raise the treadmill about halfway to the vertical position.
2. Move your right hand to the position shown, and hold the
treadmill firmly. Using your left hand, push the storage
latch to the left. Raise the treadmill until the storage latch
snaps into the catch. Make sure that the storage latch
is inside of the catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85¡ Fahrenheit.
Storage
Latch
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
storage latch is inside of the catch.
1. Hold the handrails and place one foot on the base.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. To re-
duce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
Base
Front Wheels
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand as
shown. Using your left hand, push the storage latch to the
left. Pivot the treadmill until the storage latch is past the
catch.
Storage
Latch
Catch
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. To decrease the possibility of in-
jury, bend your legs and keep your back straight.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE-SHOOTING AND MAINTENANCE
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assistance is needed, call our toll-free HELPLINE at
1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays).
PROBLEM
SOLUTION
1. The power does not
turn on
a. Make sure that the power cord is plugged into a surge suppressor, and that the
surge suppressor is plugged into a properly grounded outlet (see page 9). Use
only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage
surge suppressor (TVSS). The surge suppressor must have a UL suppressed
voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for 120 volts AC and 15 amps.
b. Make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the frame near
the power cord. If the switch protrudes as shown, the
circuit breaker has tripped. To reset the circuit
breaker, wait for five minutes and then press the
switch back in.
Tripped
Reset
d. Check the on/off switch located on the frame near the
power cord. The switch must be in the on position.
On
Position
2. The power turns off
during use
a. Check the circuit breaker (see c. above). If the circuit breaker has tripped,
wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console and then reinsert it.
d. Make sure that the on/off switch is in the on position (see d. above).
3. The walking belt
slows when walked
on
a. Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of
five feet or less in length.
b. If the walking belt is overtightened, tread-
mill performance may decrease and the
walking belt may be permanently dam-
b
3Ð4Ó
aged. Remove the key and UNPLUG THE
POWER CORD. Using the included allen
wrench, turn both rear roller adjustment
bolts counterclockwise 1/4 of a turn. When
the walking belt is properly tightened, you
should be able to lift the edges of the
walking belt 3 to 4 inches off the walking
Rear Roller Adjustment Bolts
platform. Be careful to keep the walking
belt centered. Plug in the power cord, insert the key and run the treadmill for a few
minutes. Repeat until the walking belt is properly tightened.
c. If the walking belt still slows when walked on, call our toll-free HELPLINE.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
SOLUTION
4. The walking belt is
off-center or slips
when walked on
a. If the walking belt has shifted to the
left, first remove the key and UNPLUG
THE POWER CORD. Using the allen
wrench, turn the left rear roller adjustment
bolt clockwise, and the right bolt counter-
clockwise, 1/4 of a turn each. Be careful
not to overtighten the walking belt. Plug in
the power cord, insert the key and run the
a
treadmill for a few minutes. Repeat until the walking belt is centered.
b. If the walking belt has shifted to the right,
first remove the key and UNPLUG THE
b
POWER CORD. Using the allen wrench,
turn the left rear roller adjustment bolt
counterclockwise, and the right bolt clock-
wise, 1/4 of a turn each. Be careful not to
overtighten the walking belt. Plug in the
power cord, insert the key and run the
treadmill for a few minutes. Repeat until the walking belt is centered.
c. If the walking belt slips when walked on,
first remove the key and UNPLUG THE
c
POWER CORD. Using the allen wrench,
turn both rear roller adjustment bolts clock-
wise, 1/4 of a turn. When the walking belt
is correctly tightened, you should be able
to lift the edges of the walking belt 3 to 4
inches off the walking platform. Be careful
to keep the walking belt centered. Plug in the power cord, insert the key and run
the treadmill for a few minutes. Repeat until the walking belt is properly tightened.
5. An error code (ÒE1,Ó
ÒE2,Ó ÒE3,Ó or ÒE4,Ó)
appears in the SPEED
display
a. If error code ÒE1,Ó ÒE2,Ó or ÒE3Ó appears in the SPEED display, remove the key,
wait for ten seconds, and then reinsert it. If the error code appears again, call our
toll-free HELPLINE. Do not operate the treadmill until the problem is cor-
rected.
b. Error code ÒE4Ó may appear in the SPEED display if the walking belt is moving at
a slow speed and there is excessive stress on the motor. If this occurs, remove
the key, wait for ten seconds, and then reinsert it. If you weigh over 200 pounds,
it may also be helpful to increase the incline of the treadmill. If the error code
appears again, call our toll-free HELPLINE. Do not operate the treadmill until
the problem is corrected.
6. The walking belt
becomes soiled
a. Use a color-fast upholstery cleaner to clean the walking belt. Test the
cleaner on a small area before cleaning the entire belt.
7. Bubbles form in the
walking belt
a. Due to variations in humidity and temperature, there is a possibility that
bubbles may form in the walking belt. Although the bubbles will disappear with
time, you may unplug the power cord, carefully insert a needle into the bubbles,
and push the air out of the bubbles.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
If your goal is to strengthen your cardiovascular system,
your exercise must be Òaerobic.Ó Aerobic exercise is
activity that requires large amounts of oxygen for pro-
longed periods of time. This increases the demand on
the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline until your heart rate is near
the highest number in your training zone.
WARNING:
Before beginning
this or any exercise program, consult your
physician. This is especially important for
individuals over the age of 35 or individuals
with pre-existing health problems.
The following guidelines will help you to plan your ex-
ercise program. For more information about exercise,
consult your physician or obtain a reputable book.
HOW TO MEASURE YOU HEART RATE
To measure your heart
rate, stop exercising
EXERCISE INTENSITY
and place two fingers
on your wrist as
shown. Take a six-
second heartbeat
count, and multiply the
result by ten to find
your heart rate. (A six-
second count is used
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the desired
results is to exercise with the proper intensity. The
proper intensity level can be found by using your heart
rate as a guide. The chart at the bottom of this page
shows recommended heart rates for fat burning and
aerobic exercise.
because your heart rate drops quickly when you stop
exercising.) If your heart rate is too high or too low, ad-
just the speed or incline of the treadmill accordingly.
To find the proper heart rate for you, first find your age
at the top of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers below
your age. The three numbers define your Òtraining
zone.Ó The lowest two numbers are recommended
heart rates for fat burning, and the highest number is
the recommended heart rate for aerobic exercise.
WORKOUT GUIDELINES
Each workout should include three parts: (1) a warm-
up, (2) training zone exercise, and (3) a cool-down.
Fat Burning
Warming Up
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time. During
the first few minutes of exercise, your body uses easily
accessible carbohydrate calories for energy. Only after
the first few minutes does your body begin to use stored
fat calories for energy. If your goal is to burn fat, adjust
the speed and incline of the treadmill until your heart
rate is near the lowest number in your training zone.
Begin each workout with five to ten minutes of stretch-
ing and light exercise to warm up. A proper warm-up
increases your body temperature, heart rate and circu-
lation in preparation for exercise.
Training Zone Exercise
After warming up, increase the intensity of your exer-
cise until your heart rate is in your training zone for 20
to 30 minutes. Breathe regularly and deeply as you
exerciseÑnever hold your breath.
For maximum fat burning, adjust the speed and incline
until your heart rate is near the middle number in your
training zone.
Aerobic Exercise
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Cooling Down
Exercise Frequency
End each workout with five to ten minutes of stretching
to cool down. This will develop muscle flexibility and
will help to prevent post-exercise problems.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired.
The key to success is to make exercise a regular and
enjoyable part of your everyday life.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown in the
drawings at the right. Move slowly as you stretchÑnever
bounce.
1
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings,
back of knees and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for both legs. Stretches:
Hamstrings, lower back and groin.
3
3. Calf/Achilles Stretch
4
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your
back foot flat on the floor. Bend your front leg, lean forward and
move your hips toward the wall. Hold for 15 counts, then relax.
Repeat 3 times for both legs. To cause further stretching of the
achilles tendons, bend your back leg as well. Stretches:
Calves, achilles tendons and ankles.
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close
to your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for both legs. Stretches: Quadriceps and hip
muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold
for 15 counts, then relax. Repeat 3 times. Stretches:
Quadriceps and hip muscles.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LISTÑModel No. 831.297970
R0499A
Key
No. Qty. Description
Key
No. Qty. Description
Key
No. Qty. Description
1
2
3
4
5
6
7
8
1
6
5
4
1
1
2
Rear Roller
Isolator
Hood Screw
Hood Bracket Clip
Handrail
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
1
1
1
1
1
2
8
1
1
1
1
2
1
1
1
1
1
1
1
2
1
1
1
2
1
2
2
2
4
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
1
2
1
6
1
Power Supply w/Clips
Controller
Power Cord Grommet
Power Cord
Pulse Sensor Housing
Handrail Bolt
Handrail/Pivot Washer
Pulse Sensor Cap
Console Base
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
#
#
#
#
#
#
#
#
#
6
1
2
3
1
1
1
1
1
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
Center Grip Tape
Choke Bracket
Console Screw, Long
Incline Warning Decal
Left Rear Grip Tape
Choke
Motor Tension Bolt
Storage Catch Bolt
Handrail Cap (right)
Storage Catch Nut
Plastic Box
Box Screw
Roller Guard
Handrail Cap (left)
Belt Guide
8Ó Black Ground Wire
4Ó Black Wire, 2 F
20Ó White Wire, 2 F
4Ó White Wire, M/F
8Ó Blue Wire, 2 Female
4Ó Blue Wire, 2 F
8Ó Red Wire, M/F
4Ó Green F/Ring
UserÕs Manual
Walking Platform
Frame Pivot Bolt
38 Screw
Rear Platform Screw
9
2
2
6
1
5
1
1
2
2
1
1
1
1
1
1
1
1
6
1
1
1
6
1
6
1
1
1
1
2
1
2
1
2
2
2
4
1
1
1
2
1
2
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49*
50
Cable Tie Clamp
Small Screw
Releasable Tie
8Ó Cable Tie
Belly Pan
Console
Electronics Bracket
Latch Screw
Book Rack
Key/Clip
Storage Latch
Rear Roller Ground Wire
Incline Warning Decal
Storage Catch
Incline Motor Spacer
Endcap Insert
Wrench Clip
Hood
Frame Pivot Spacer
Console Bushing
Right Rear Grip Tape
Incline Leg
Shock
Front Roller/Pulley
Walking Belt
Motor Tension Nut
Motor Star Washer
Motor Tension Washer
Incline Motor Bolt
Motor
Allen Wrench
Wire Harness Grommet
Upright Base Endcap
Motor Pivot Washer
Wheel Nut
Front Wheel
Wheel Bolt
Base Pad
Left Front Grip Tape
Wire Harness
Upright/Base
Incline Motor Plate
Incline Motor Shield
4Ó Cable Tie
Incline Optic Disk
23Ó Cable Tie
Incline Motor
Incline Stop Bracket
Right Front Grip Tape
Photo Switch Wire
Frame
Right Endcap
Left Endcap
Endcap Pad
Motor-Controller Wire
Rear Roller Adjust. Bolt
Latch Decal
* Includes all parts shown in the box.
# These parts are not illustrated
Motor Belt
Pulley/Flywheel/Fan
Motor Pivot Nut
Front Roller Adjust. Bolt
Adjustment Washer
Motor Pivot Bolt
Front Roller Adjust.Nut
Speed Optic Disk
Optic Switch Bracket
Optic Switch Bolt
Bracket Nut
Specifications are subject to change
without notice.
Optic Switch
Optic Switch Star Washer
Optic Switch Nut
Hood Bracket, Short
Grommet
Plastic Stand-Off
Power Cord Bracket
On/Off Switch
Circuit Breaker
Handrail Endcap
Motor/Pulley/Fly./Fan
Hood Bracket (long)
Platform Screw
Electronics Shield
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
The model number and serial number of your HealthRider¨ SOFT-
STRIDER S200ª treadmill are listed on a decal attached to the
frame. See the front cover of this manual to find the location of the
decal.
Model No. 831.297970
QUESTIONS?
All replacement parts are available for immediate purchase or
special order when you visit your nearest SEARS Service Center.
To request service or to order parts by telephone, call the toll-free
numbers listed at the left.
If you find that:
¥ you need help assembling or
operating the HealthRider¨
SOFTSTRIDER S200ª treadmill
When requesting help or service, or ordering parts, please be
prepared to provide the following information:
¥ a part is missing
¥ The NAME OF THE PRODUCT (HealthRider¨ SOFTSTRIDER
S200ª treadmill)
¥ or you need to schedule repair
service
call our toll-free HELPLINE
¥ The MODEL NUMBER OF THE PRODUCT (831.297970)
1-800-736-6879
MondayÐSaturday, 7 amÐ7 pm
Central Time (excluding holidays)
¥ The KEY NUMBER AND DESCRIPTION OF THE PART (see the
EXPLODED DRAWING and PART LIST included in this manual)
REPLACEMENT
PARTS
If parts become worn and need
to be replaced, call the following
toll-free number
1-800-FON-PART
(1-800-366-7278)
FULL 90 DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
SEARS TREADMILL EXERCISER, contact the nearest SEARS Service Center throughout the United
States and SEARS will repair or replace the TREADMILL EXERCISER, free of charge.
This warranty does not apply when the TREADMILL EXERCISER is used commercially or for rental pur-
poses.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179
Part No. 155444 J00911-C R0499A
Printed in USA © 1999 Sears, Roebuck and Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
|