Model No. HREL3006.1
Serial No.
USER’S MANUAL
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-922-4222
Mon.–Fri., 6 a.m.–6 p.m. MST
(closed on holidays)
ON THE WEB:
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manu-
al for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the elliptical exerciser.
1. Read all instructions in this manual before
using the elliptical exerciser.
11. Keep your back straight while using the ellip-
tical exerciser; do not arch your back.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
12. If you feel pain or dizziness at any time
while exercising, stop immediately and cool
down.
3. The elliptical exerciser is intended for
home use only. Do not use the elliptical
exerciser in a commercial, rental, or institu-
tional setting.
13. When you stop exercising, allow the pedals
to slowly come to a stop.
14. The decal shown below has been placed on
the elliptical exerciser. If the decal is miss-
ing or illegible, call the toll-free telephone
number on the front cover of this manual
and order a free replacement decal. Apply
the decal in the location shown.
4. Place the elliptical exerciser on a level sur-
face, with a mat beneath it to protect the
floor or carpet. Keep the elliptical exerciser
indoors, away from moisture and dust.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
6. Keep children under 12 and pets away from
the elliptical exerciser at all times.
7. The elliptical exerciser should not be used
by persons weighing more than 250 pounds.
8. Wear appropriate exercise clothes while
using the elliptical exerciser. Always wear
athletic shoes for foot protection while exer-
cising.
9. Hold the handgrip pulse sensor or the han-
dlebars when mounting, dismounting, or
using the elliptical exerciser.
10. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
WARNING:
Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for selecting the versatile new
tions after reading this manual, please see the front
cover of this manual. To help us assist you, please
note the product model number and serial number
before contacting us. The model number is
®
HEALTHRIDER C515e. The HEALTHRIDER C515e
is an incredibly smooth exerciser that moves your feet
in a natural elliptical path, minimizing the impact on
your knees and ankles. And the unique C515e fea-
tures adjustable resistance and a state-of-the-art con-
sole to help you get the most from your exercise.
HREL3006.1. The serial number can be found on a
decal attached to the elliptical exerciser (see the front
cover of this manual for the location of the decal).
For your benefit, read this manual carefully before
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
you use the elliptical exerciser. If you have ques-
Fan
Handgrip Pulse Sensor
Handlebar
Console
Water Bottle Holder*
FRONT
Pedal
Wheel
Leveling Foot
Pedal Disk
LEFT SIDE
BACK
*No water bottle is included
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
To hire an authorized service technician to assemble the elliptical exerciser, call toll-free 1-800-445-2480.
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the
included hex keys, assembly requires a phillips screwdriver
, an adjustable
wrench
, and a rubber mallet
.
Use the drawings below to identify the small parts used in assembly. The number in parentheses below each
drawing refers to the key number of the part, from the PART LIST on page 18. The second number refers to the
quantity needed for assembly. Note: Some small parts may have been pre-assembled. If a part is not in the
parts bag, check to see if it has been pre-assembled.
Wave Washer
(95)–2
Large Wave
M8 Split
M10 Split
M8.5 Washer
(53)–12
Washer (20)–2
Washer (58)–4
Washer (70)–2
M4 x 16mm
M4 x 22mm
M8 Nylon
Locknut (46)–8
M10 Nylon
Locknut (29)–4
Frame Spacer (83)–2
Screw (66)–4
Screw (93)–2
M8 x 45mm Button
Bolt (50)–4
M8 x 25mm Patch
Screw (22)–4
M8 x 65mm Button
Bolt (89)–4
M10 x 88mm Button Screw (63)–2
M8 x 50mm Button
Bolt (82)–4
M10 x 112mm Carriage Bolt (34)–4
M10 x 52mm Bolt Set (27)–2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
1
To make assembly easier, read the information
on page 5 before you begin assembling the
elliptical exerciser.
32
34
29
32
Identify the Front Stabilizer (3). While another person
lifts the front of the Frame (1), attach the Front
Stabilizer to the Frame with two M10 x 112mm
Carriage Bolts (34) and two M10 Nylon Locknuts (29).
Make sure that the Front Stabilizer is turned so the
Wheels (32) are not touching the floor.
3
1
29
2. While another person lifts the back of the Frame (1),
attach the Rear Stabilizer (4) to the Frame with two
M10 x 112mm Carriage Bolts (34) and two M10 Nylon
Locknuts (29).
2
29
4
29
1
34
3. While another person holds the Upright (2) in the posi-
tion shown, connect the Upper Wire Harness (86) to
the Lower Wire Harness (87). Carefully pull the
upper end of the Upper Wire Harness to remove
any slack. While holding the upper end of the
Upper Wire Harness, insert the Upright into the
Frame (1). Do not pinch the Wire Harnesses.
3
Avoid pinching
or damaging the
wire harnesses
during this step.
91
2
Slide two M10 Split Washers (70) and two Frame
Spacers (83) onto two M10 x 88mm Button
93
Screws (63). Insert the Button Screws into the Frame
(1) and the Upright (2). Make sure that the concave
end of the Frame Spacer is turned toward the
Frame. Do not tighten the Button Screws yet.
86
87
Attach the Water Bottle Holder (91) to the
Upright (2) with two M4 x 22mm Screws (93).
70
70
83
83
1
63
4. The Console (5) requires four “D” batteries (not includ-
ed); alkaline batteries are recommended. Remove the
battery cover from the Console and insert four batter-
ies into the Console. Make sure that the batteries
are oriented as shown by the markings on the bat-
tery cover. Then, reattach the battery cover.
4
5
Batteries
Battery
Cover
Batteries
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. While another person holds the Console (5) in the
position shown, connect the wire harness on the
Console to the Upper Wire Harness (86). Insert the
excess wire harness into the Upright (2). Next, attach
the Console to the Upright with four M4 x 16mm
Screws (66). Be careful to avoid pinching the wire
harnesses.
5
Wire
Harness
86
5
66
Avoid pinching
or damaging the
wire harnesses
during this step.
2
66
6. Identify the Left Handlebar (9), which is marked with a
“Left” sticker. Insert the Left Handlebar into one of the
Handlebar Legs (79); make sure that the Handlebar
Leg is turned so the hexagonal holes are on the
indicated side. Attach the Left Handlebar to the
Handlebar Leg with two M8 x 45mm Button Bolts (50)
and two M8 Nylon Locknuts (46). Make sure that the
Nylon Locknuts are inside the hexagonal holes. Do
not tighten the Button Bolts yet.
6
9
Repeat this step for the Right Handlebar (not
shown) and the other Handlebar Leg.
46
50
Hexagonal
Holes
79
7. Apply a generous amount of the included grease to the
Pivot Axle (38) and to an M8.5 Washer (53). Next, insert
the Pivot Axle into the Upright (2) and center it. Reapply
grease to both ends of the Pivot Axle.
7
Slide a Handlebar Spacer (25) onto the short tube on
the Left Handlebar (9), and rotate the Handlebar Spacer
so the small arrow is pointing downward. Next, slide the
Left Handlebar onto the left end of the Pivot Axle (38).
Hand tighten an M8 x 25mm Patch Screw (22) with an
M8.5 Washer (53) and a Wave Washer (95) into the end
of the Pivot Axle. Then, press the small tabs on a
Handlebar Cap (23) into the Handlebar Spacer.
Grease
Tube
9
38
25
53
2
22
Arrow
95
Assemble the Right Handlebar (not shown) and the
other Handlebar Leg in the same way.
23
Tighten both M8 x 25mm Patch Screws (22) at the same
time.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Identify the Left Pedal Leg (14), which is marked with a
“Left” sticker. Attach a Pedal Bracket (15) to the Left
Pedal Leg with two M8 x 65mm Button Bolts (89), two
M8.5 Washers (53), and two M8 Nylon Locknuts (46).
8
13
89
53
Next, identify the Left Pedal (13). Attach the Left Pedal
to the Left Pedal Leg (14) with two M8 x 50mm Button
Screws (82), two M8 Split Washers (58), and two M8.5
Washers (53).
14
15
Repeat this step with the Right Pedal Leg (not
shown) and the Right Pedal (not shown).
46
53
82
58
58
9. Apply a generous amount of grease to the Left Crank
Arm (36) and to a Large Wave Washer (20). Then, slide
a Pedal Leg Spacer (88) and the Left Pedal Leg (14)
onto the Left Crank Arm.
9
17
Attach the Left Pedal Leg (14) to the Left Crank
Arm (36) with an M8 x 25mm Patch Screw (22), an
M8.5 Washer (53), and the Large Wave Washer (20).
Grease
Attach the Right Pedal Leg (17) in the same way.
14
88
36
20
22
53
10.Hold the lower end of the left Handlebar Leg (79) inside
of the Left Pedal Leg (14). Apply a small amount of
grease to an M10 x 52mm Bolt Set (27). Attach the left
Handlebar Leg to the Left Pedal Leg with the Bolt Set.
Do not overtighten the Bolt Set; the left Handlebar
Leg must be able to pivot freely.
10
79
17
79
Grease
27
Grease
27
Attach the right Handlebar Leg (79) to the Right
Pedal Leg (17) in the same way.
14
11. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be
left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the ellip-
tical exerciser.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE ELLIPTICAL EXERCISER
HOW TO EXERCISE ON THE ELLIPTICAL
EXERCISER
HOW TO USE THE HANDLEBARS
The handlebars are
designed to add
To mount the elliptical exerciser, hold the handgrip
Handlebars
Handgrip
Pulse
pulse sensor and step onto the pedal that is in the low- upper-body exer-
est position. Then, step onto the other pedal. Push the cise to your work-
Sensor
pedals until they begin to move with a continuous
motion. Note: The pedal disks can turn in either
direction. It is recommended that you move the
pedal disks in the direction shown by the arrow
below; however, for variety, you can turn the pedal
disks in the opposite direction.
outs. Push and pull
the handlebars as
you exercise to
work your arms,
shoulders, and
back.
To exercise only
your lower body,
hold the handgrip
pulse sensor as
you exercise.
Handgrip
Pulse Sensor
Handlebars
Pedals
Pedal Disk
To dismount the elliptical exerciser, wait until the ped-
als come to a complete stop. Note: The elliptical
exerciser does not have a free wheel; the pedals
will continue to move until the flywheel stops.
When the pedals are stationary, step off the higher
pedal first. Then, step off the lower pedal.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM OF THE CONSOLE
Increase
Button
Fan
Program
Profiles
Button
Program Button
Program
Indicator
Display
Pace
Decrease
Button
Guide
FEATURES OF THE CONSOLE
prompt you to vary your pedaling pace while guiding
you through an effective workout.
This advanced console offers a selection of features
designed to make your workouts more effective. When To use the manual mode of the console, see the
you use the manual mode of the console, you can
instructions on page 11. To use a preset program,
change the resistance of the pedals with the touch of a see page 12.
button. As you pedal, the console will provide continu-
ous exercise feedback. You can even measure your
heart rate using the built-in handgrip pulse sensor.
Before using the console, make sure that batteries are
installed (see assembly step 4 on page 6). If there is a
sheet of clear plastic on the display, remove the plastic.
The console also offers eight preset programs that
automatically change the resistance of the pedals and
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Measure your heart rate if desired.
If there are sheets
HOW TO USE THE MANUAL MODE
Turn on the console.
5
Contacts
of clear plastic on
1
the metal con-
tacts on the hand-
To turn on the console, press the Increase button
or begin pedaling. The pace guide will light for a
moment; the console will then be ready for use.
grip pulse sensor,
remove the plas-
tic. Next, hold the
handgrip pulse
Select the manual mode.
2
3
sensor with your palms resting on the contacts.
When your pulse is detected, the heart-shaped
indicator in the lower half of the display will flash
each time your heart beats, and then your heart
rate will appear in the display.
When you turn on the console, the manual mode
will be selected. If you have selected a program,
reselect the manual mode by pressing the
Program button repeatedly until no program indi-
cators (see the drawing on page 10) appear along
the left side of the display.
For the most accurate heart rate reading, continue
to hold the handgrip pulse sensor for about 30
seconds. Note: If you continue to hold the hand-
grip pulse sensor, the display will show your heart
rate for about 30 seconds. The display will then
show your heart rate along with the other modes.
Change the resistance of the pedals as
desired.
As you pedal,
change the resis-
If your heart rate does not appear, make sure that
your hands are positioned as described. Avoid
moving your hands excessively or squeezing the
metal contacts too tightly. For optimal perfor-
mance, periodically clean the metal contacts
using a soft cloth; never use alcohol, abrasives,
or chemicals to clean the contacts.
tance of the pedals
by pressing the
Increase and
Decrease buttons.
There are ten resistance levels. Note: After you
press the buttons, it will take a moment for the
pedals to reach the selected resistance level.
Turn on the fan if desired.
Follow your progress with the display.
6
7
4
To turn on the fan at low speed, press the Fan
button. To turn on the fan at high speed, press
the Fan button a second time. To turn off the fan,
press the Fan button a third time. Note: If the fan
is turned on but the pedals do not move for thirty
seconds, the fan will automatically turn off to con-
serve the batteries.
The upper half of
the display will
show the elapsed
time, the distance
(in total revolutions)
you have pedaled,
and the resistance level of the pedals. The display
will change modes every few seconds. Note:
When a preset program is selected, the display
will show the time remaining in the program
instead of the elapsed time.
Rotate the thumb
Thumb Tab
tab on the right
side of the fan to
adjust the angle of
the fan.
The lower half of
the display will
show your pedaling
speed, in revolu-
When you are finished exercising, the console
will turn off automatically.
tions per minute
(RPM), and the
approximate number of calories you have burned.
The display will change modes every few sec-
onds. The lower half of the display will also show
your heart rate when you use the handgrip pulse
sensor (see step 5).
If the pedals do not move for a few seconds, the
time will begin to flash in the display and the con-
sole will pause. If the pedals do not move for a
few minutes, the console will turn off and the dis-
play will be reset.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
When one of the two lower indicators lights,
increase your pace; when one of the two upper
indicators lights, decrease your pace. When the
center indicator lights, maintain your current
pace. Important: The pace guide is intended
only to provide a goal. Make sure to pedal at a
pace that is comfortable for you.
HOW TO USE A PRESET PROGRAM
Turn on the console.
1
See step 1 on page 11.
Select a preset program.
2
To select a preset
program, press
the Program but-
ton repeatedly
until the number 1,
2, 3, 4, 5, 6, 7, or
8 appears along
The display will show the time remaining in the
program. If you stop pedaling for a few seconds,
the program will pause and the time will flash in
the display. To restart the program, simply resume
pedaling.
the left side of the display. When you select a
preset program, the display will show the length
of the program.
Begin pedaling to start the program.
3
Follow your progress with the display.
See step 4 on page 11.
Each preset program consists of several one-
minute segments. One resistance level and one
target pace are programmed for each segment.
4
5
6
7
Measure your heart rate if desired.
See step 5 on page 11.
At the end of each segment, the resistance level
will flash in the display for a few seconds. The
resistance of the pedals will then automatically
change to the resistance level programmed for
the next segment. Note: If the resistance level is
too low or too high, you can override it by press-
ing the Increase and Decrease buttons. However,
when the current segment ends, the resistance
will automatically change to the resistance level
programmed for the next segment.
Turn on the fan if desired.
See step 6 on page 11.
When you are finished exercising, the con-
sole will turn off automatically.
During the program, the pace guide will prompt
you to increase or decrease your pedaling pace.
See step 7 on page 11.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLESHOOTING
Inspect and tighten all parts of the elliptical exerciser
regularly. Replace any worn parts immediately.
HANDGRIP PULSE SENSOR TROUBLESHOOTING
• Avoid moving your hands while using the handgrip
pulse sensor. Excessive movement may interfere
with heart rate readings.
To clean the elliptical exerciser, use a damp cloth and
a small amount of mild soap. Important: To avoid
damage to the console, keep liquids away from
the console and keep the console out of direct
sunlight.
• Do not hold the metal contacts too tightly; doing so
may interfere with heart rate readings.
BATTERY REPLACEMENT
• For the most accurate heart rate reading, hold the
metal contacts for about 30 seconds.
If the console display becomes dim, the batteries
should be replaced; most console problems are the
result of low batteries. See assembly step 4 on page
6 for replacement instructions.
• For optimal performance of the handgrip pulse sen-
sor, keep the metal contacts clean. The contacts
can be cleaned with a soft cloth—never use alcohol,
abrasives, or chemicals to clean the contacts.
HOW TO LEVEL THE ELLIPTICAL EXERCISER
After the elliptical
exerciser has
been moved to
the location
where it will be
used, make sure
that the ends of
both stabilizers
Leveling Foot
are touching the
floor. If the ellipti-
cal exerciser
rocks slightly during use, turn one or both of the level-
ing feet under the front stabilizer until the rocking
motion is eliminated.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
WARNING:
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
gy. Only after the first few minutes of exercise does
your body begin to use stored fat calories for energy.
If your goal is to burn fat, adjust the intensity of your
exercise until your heart rate is near the lowest num-
ber in your training zone as you exercise.
Before beginning this or any exercise pro-
gram, consult your physician. This is espe-
cially important for persons over the age of 35
or persons with pre-existing health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
For maximum fat burning, adjust the intensity of your
exercise until your heart rate is near the middle num-
ber in your training zone as you exercise.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exer-
cise is activity that requires large amounts of oxygen
for prolonged periods of time. This increases the
demand on the heart to pump blood to the muscles,
and on the lungs to oxygenate the blood. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone as you exercise.
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition
and adequate rest are essential for successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning, maximum fat
burning, and cardiovascular (aerobic) exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A warm-up, consisting of 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa-
ration for exercise.
Training zone exercise, consisting of 20 to 30 min-
utes of exercising with your heart rate in your training
zone. Note: During the first few weeks of your exer-
cise program, do not keep your heart rate in your
training zone for longer than 20 minutes.
To find the proper heart rate for you, first find your age
at the bottom of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers above
your age. The three numbers are your “training zone.”
The lower two numbers are recommended heart rates
for fat burning; the highest number is the recommend-
ed heart rate for aerobic exercise.
A cool-down, with 5 to 10 minutes of stretching. This
will increase the flexibility of your muscles and will
help to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exer-
cise, you may complete up to five workouts each week
if desired. The key to success is to make exercise a
regular and enjoyable part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relative-
ly low intensity level for a sustained period of time.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right.
Move slowly as you stretch—never bounce.
1
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times for each leg. Stretches: Hamstrings, lower
back and groin.
3. Calf/Achilles Stretch
3
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles ten-
dons, bend your back leg as well. Stretches: Calves, achilles ten-
dons and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your but-
tocks as possible. Hold for 15 counts, then relax. Repeat 3 times
for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
5
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
16
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. HREL3006.1
R0806A
Key No. Qty.
Description
Key No. Qty.
Description
1
1
1
1
1
1
1
1
2
1
1
2
1
1
1
2
2
1
2
1
2
2
4
2
6
2
2
2
4
4
1
1
2
2
4
2
1
1
1
1
2
1
2
1
1
4
11
2
1
1
4
Frame
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
#
4
1
12
1
1
1
4
4
4
4
4
4
2
2
8
6
4
1
1
2
2
2
1
8
2
1
1
1
2
1
1
4
2
4
1
1
1
2
4
4
1
4
2
1
2
2
2
1
1
M6 x 18mm Bolt
“C” Magnet Bracket
M8.5 Washer
2
Upright
3
Front Stabilizer
Rear Stabilizer
Console
4
“C” Magnet
5
Motor
6
Left Side Shield
Right Side Shield
Pedal Disc
Belt
7
M8 x 47mm Button Bolt
M8 Split Washer
M6 Nylon Locknut
M6 Nut
8
9
Left Handlebar
Right Handlebar
Foam Grip
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
M5 Nylon Locknut
M5 x 12mm Bolt
M10 x 88mm Button Screw
Right Pedal
Left Pedal
Left Pedal Leg
Pedal Bracket
M4 x 6mm Self-tapping Screw
M5 x 33mm Screw
M4 x 16mm Screw
M4 x 25mm Screw
Right Front Endcap
Reed Switch Clamp
M10 Split Washer
Handlebar Endcap
Leveling Foot
Outer Pedal Leg Bushing
Right Pedal Leg
Inner Pedal Leg Bushing
Upright Endcap
Large Wave Washer
Snap Ring
M8 x 25mm Patch Screw
Handlebar Cap
Handlebar Bushing
Handlebar Spacer
Upright Spacer
M10 x 52mm Bolt Set
Front Flex Bushing
M10 Nylon Locknut
Upright Bushing
Left Front Endcap
Wheel
M5 x 16mm Screw
M4 x 19mm Screw
M6 Eyebolt
Spring
Reed Switch
Reed Switch Bracket
Handlebar Leg
Side Shield Cover
“U” Bracket
M8 x 50mm Button Screw
Frame Spacer
M6 x 72mm Button Screw
M10 x 112mm Carriage Bolt
Rear Stabilizer Endcap
Left Crank Arm
Pulley
M4 x 12mm Tap Screw
Resistance Cable
Upper Wire Harness
Lower Wire Harness
Pedal Leg Spacer
M8 x 65mm Button Bolt
Motor Washer
Pivot Axle
Crank
Crank Bearing
Flywheel
Water Bottle Holder
M8 Nut
Flywheel Bearing
Magnet
M4 x 22mm Screw
M6 Large Washer
Wave Washer
Flywheel Axle
M8.5mm Small Washer
M8 Nylon Locknut
Crank Screw
M3 x 16mm Screw
Hex Key
Right Crank Arm
M6 x 25mm Bolt
M8 x 45mm Button Bolt
#
Grease
#
User’s Manual
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. HREL3006.1
R0806A
12
5
19
71
71
11
46
53
89
91
24
10
53
58
26
96
15
46
93
11
53
89
58
82
53
20
22
16
53
23
17
18
66
24
38
88
67
22
7
53
74
24
9
95
26
96
50
51
74
51
95
24
22
23
25
24
46
24
25
46
74
53
2
74
6
79
50
87
27
79
86
68
28
80
74
8
74
67
28
27
30
64
84
62
65
84
46
70
83
63
90
90
55
64
60
27
27
3
94
75
34
85
28
51
61
72
32
61
29
59
1
59
21
47
33
72
51
31
52
40
21
41
29
48
39
40
59
32
66
69
66
45
42
46
54
35
42
81
44
29
57
4
77
78
76
13
45
60
73
43
36
45
49
57
75
46
60
29
45
35
92
47
34
88
8
37
89
14
15
53
92
18
56
53
53
53
58
16
22
46
20
65
82
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, please be
prepared to give the following information when contacting us:
• the MODEL NUMBER of the product (HREL3006.1)
• the NAME of the product (HEALTHRIDER C515e)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see page 18)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped
to a service center, freight charges to and from the service center will be the customer’s responsibility. For
in-home service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse,
improper or abnormal usage or repairs not provided by an ICON authorized service center; products used
for commercial or rental purposes; or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci-
dental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 246137 R0806A
Printed in China © 2006 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|