HIGHLANDER
Residential Platform Lift
RPL400
RPL600
This manual has been provided to assist
you with lift installation and operation.
For further assistance please contact
your authorized Harmar dealer or
Harmar’s Technical Service department.
Tel: 866-378-6648
Fax: 816-537-0641
Download from Www.Somanuals.com. All Manuals Search And Download.
3
When You Receive the Lift
• Check the lift for shipping damage. If you see any damage contact the freight carrier to file a damage
claim.
• Verify the products match that described on the packing list attached to the exterior packaging.
• Verify the contents of the package match that shown below to the right.
Specifications
Payload Capacity
Vertical Travel
Height
600 lbs
54”
77”
Foot Print
49” x 69”
34” x 54”
115vac - 20a
24vac
Platform Size
Input Voltage
Control Voltage
Platform Speed
Motor
10 ft/min
1/2hp-90vdc
Safety
• Read all instructions in this manual before installing or operating the lift.
• Do not exceed the maximum payload capacity of 600 lbs.
• Do not ride on the lift until it is anchored in place.
• This product is designed only for lifting people and wheel chairs. Do not use it for any other purpose.
• Always wear eye protection while installing or servicing this product.
• Always disconnect this product from the electrical source before servicing it.
• Only use the fasteners supplied with this lift.
• Do not wear loose clothing or jewelry when working on this product.
• Do not disable any safety equipment or switches supplied with this lift.
• Stay away from all drive train components while the lift is operating.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Code Requirements
Your lift has been designed to meet ASME A18.1 section 5 and CSA B44/ASME A17.5, with the
addition of certain options. Code requirements for Vertical Platform lifts vary depending on location.
It is the installers responsibility to contact their local code enforcement office and determine all of the
regulations they are subject to. You must do this before installing the Vertical Platform Lift.
Site Requirements
•
•
•
•
The lift will require a 115vac 20amp grounded circuit.
Outdoor Installations will require a GFI protected circuit.
Only install the lift on a 4” thick , level 3,500 psi reinforced concrete slab.
Foot Print 49” x 69” (this includes the folding access ramp)
Required tools
•
•
•
•
•
•
•
1/2" Hammer Drill
3/8" Masonry Drill Bit
Appliance Dolly
Hammer
Level
Measuring Tape
Socket Wrench Set
Required materials
•
4 Floor anchors
Harmar recommends securing the lift using our Anchor Kit. If you purchase you own
floor anchors they must use 3/8” bolts and have a minimum tensile strength of 6000 LBS.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Preparing to Install the Lift
Final Site Inspection
Verify the surface the lift will mount to is smooth and level. This surface must be made from 3,500 psi
reinforced concrete with a minimum thickness of 4”.
Verify that there is enough space for the lifts foot print. Be sure to include space for the folding access
ramp. (49” x 69”)
Caution: Verify that the running clearance around the lift complies with
any codes for your area.
•
•
The horizontal gap between the edge of the platform and the upper landing must no less than 3/8”
and no greater than 3/4”.
The horizontal gap between the guard panel and any wall or barrier must be no less than 2” and
no greater than 3”.
•
•
It is recommended that a gate or door be installed at the upper landing.
Verify that sufficient head room exists above the lift. The lift will require 6’ 8” of clearance above
the platform floor when the lift is at the upper landing.
Warning: The area between the floor where the lift is mounted and the top
landing must be covered by a smooth vertical fascia. This is to to eliminate any pinch
points between the platform and landing.
Connecting to Electricity
The lift will require a 115 VAC 20 amp grounded electrical outlet within 6 feet of the lift.
Plug the lift directly into the power outlet. Do not plug anything else into same outlet as the lift.
Warning: Do not ride on the lift until it has been anchored in place.
Controller Harness Connections
High Voltage
Circuit Breaker
(AC unit only)
Upper & Lower
Safety Pan
Jumper
Upper & Lower
Limit Switches
Call‐Sends
Low Voltage
Circuit Breaker
Platform
Traveling Cable
Upper Landing
Interlock
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Installing the Platform
Step 1
Step 3
The mounting bolts, nuts and spacers that
secure the platform to the lift carriage are
preinstalled in the carriage flange. Begin by
removing these pieces and setting aside.
Align the four mounting holes and insert a ½”
x 3” bolt into each hole. The upper holes
have a spacer that must be placed in
between the carriagne flange and platform
leg. Install the locknut on each bolt and
tighten sufficiently (approx. 50 lb-ft.).
Step 2
Position the platform by aligning the support
legs with the carriage flanges that protrude
from the front cover.
Step 4
Plug in the harness for the platform safety
pan and unplug the safety pan jumper on the
controller (ref pg 5). Secure the harnesses
under the clip on top of the carriage
flange.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Installing the Outer Guard Panel
Step 1
Step 2
Remove the hexbolts on the ends of the
platform. Insert the guard panel posts into
the pockets in the platform. The smooth side
of the guard panel should face in towards the
center of the platform.
Install the platform control box on the rear
guard panel using screws and nuts through
the panel.
Step 3
Plug in the harness for the platform control
box. Secure the harnesses under the clip on
top of the carriage flange.
If you have a 90 degree exit platform, install
the end guard panel using the provided
bracket and bolt to inner guard panel.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Installing the Ramp
Step 1
Step 3
Install the ramp roller guide on the side of the
lift tower using the screws already installed in
the panels.
Attach the ramp to the pivot tabs using shoulder
bolts and locking nuts. Tighten the nuts until
they seat against the bolt shoulder.
Step 4
Attach the ramp roller arm by bolting it to the
underside of the ramp.
Step 2
Attach the two ramp pivot tabs to the lower
landing sides of the platform. Reinsert the hex
bolts, one of which will go through the guard
panel post, and tighten.
The ramp roller should align and make contact
with the ramp roller guide.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Anchoring the Lift
Step 1
• Position the lift in its final location.
• Verify that it is level and perpendicular to its
surroundings.
• Shim if necessary.
Anchors
Harmar recommends securing the lift using
our Anchor Kit. If you purchase you own floor
anchors they must use 1/2-13 bolts and have
a minimum tensile strength of 6000 LBS.
Warning: All four floor anchors
must be installed correctly in
accordance to
their instructions.
Verify that the holes you have drilled are
deep enough to accept the anchors.
Step 2
Use the lift’s base as a template. Drill 4 holes
into the concrete.
Tip: Concrete dust may have settled into
the holes you just drilled. Use a shop
vacuum to clean out these holes. This will
ensure the floor anchors set correctly.
Step 3
Secure the lift in place by tightening the floor
anchor bolts.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Setting the Limit Switches
Your lift is equipped with upper and lower limit switches. The vertical location of these switches may be
adjusted to fit your application.
Typically the upper limit switch will need to be adjusted so the platform will stop level with the upper
landing. The lower limit will typically not need adjusting.
Step 1
Step 2
Verify the emergency switch is in the ON
position. Run the lift in the up direction until
the platform floor is level with the upper
landing.
Remove the screws at the top of the lift that
attach the front cover.
1A Unplug the lift’s power cord from the wall
before going to the next step (AC units).
Step 3
Remove the front cover by tilting it forward
and lifting upwards. The bottom of the front
cover sets on a pin on either side of the lift
frame. Set the cover aside in a safe location
where it will not get damaged.
1B Uplug the power cable from the battery
box before going to the next step (DC units).
Warning: Moving components can cut
and crush. Do not operate the lift if you
are in close proximity to any drive
components. Be aware that loose
clothing or jewelry may catch on moving
parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Step 4
Step 7
Loosen the bolts that attaches the upper limit
switch assembly. Slide the assembly down
the track until the lower switch in the
assembly comes in contact with the lift’s car.
You should hear the limit switch click as
contact is made. Retighten the set screw
fastening the limit switch assembly in place.
Run the lift in the down direction for several
inches. Next, run the lift in the up direction.
Continue to press the up button until the
upper limit switch has caused the lift to stop.
Step 8
Verify that the platform has stopped level
with the upper landing. If it has not, readjust
the limit until it is level.
Step 5
Replace the front cover and secure it with
the screws you removed in step 1.
Step 6
Plug the lifts electricial cord into the wall.
Verify that the emergency switch is in the on
position.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Verifying Operation of the Lift
Caution: Complete the following section before training the customer to use
the lift.
Step 1
Run the lift up and down for 5 complete cycles. Hold the direction button down and allow the limit
switches to stop the lift. At the top, verify that the platform stops level with the upper landing. At the
bottom, verify the access ramp unfolds and rests on the ground.
Step 2
Verify the operation of the Emergency stop switch. When this switch is pushed the lift should not run in
either direction. When this switch is pulled back out, the lift should operate normally.
Step 3
Verify the operation of the sensor pan underneath the platform. Start with the lift at the top landing. Press
up on the sensor pan. While holding the pan in this location, press the down switch on the platform. The
lift should not run.
Warning: Do not run the lift if anyone is under the platform.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Manual Override
Your lift is equipped with a manual handcrank, to be used in the case of a power failure.
Step 1
Step 4
Before using the manual handcrank verify
that it’s use is required. Check that the
emergency stop switch is pulled out. Check
that the electrical cord is plugged into the
wall. Also check that the buildings circuit
breaker has not tripped. Try to run the lift by
pushing both the up and down buttons. If the
lift still will not run, complete the following
steps:
Insert the manual handcrank into the
opening on the top of the brake assembly. It
may be neccesary to slightly rotate the
handcrank until it fully seats down on the hex
portion of the brake. Rotate the crank to
raise or lower the platform.
Warning: Never operate the lift while the
manual override crank is inserted into the
lift.
Step 2
Unplug the lift from the wall.
Warning: Do not service or operate the
manual handcrank while the lift is
connected to electricity.
Step 3
Remove the screws and remove the top cap
at the top of the tower.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Top Landing Gate (optional)
The optional top landing gate is provided with a combination
mechanical lock and electric contact (interlock).
A length of multi‐conductor wire will
need to be ran from the bottom of the lift
tower up to the landing gate. Consult
local codes for type and mounting
requirements.After wiring is completed,
the wiring harness must be plugged into
it appropriate receptacle on the
The interlock:
•
•
Prevents the lift from running if the gate is not closed.
Prevents the gate from being opened if the platform is
not at the top landing.
•
Unlocks when the lift is on the upper limit switch.
controller (ref pg 5).
Wiring Connections
Gate Harness
Black
Lift Harness
Orange
Green
Black
Yellow
Black
Yellow
Brown
Call‐Send Harness
Lift Harness
Blue
Blue
Yellow
Red
White
Red
A crescent shaped key is provided to manually
unlock the gate during installation. The key is
inserted from the back side to lift up on the solenoid
that holds the gated locked.
Mount the gate by placing onto the upper landing
making sure to align the gate opening with the
platform (outer guard rail not shown for clearity).
There are a number of attachment holes provided in
the threshold portion of the gate for mounting using
wood lag screws or concrete anchors as
appropriate.
Remove the latch post cover and connect the call-
send and interlock wire harnesses.
The vertical posts of the gate must be attached to a
supporting structure, (the gate is not designed to be
freestanding).
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Top Landing EMI Interlock (optional)
The optional EMI Interlock is provided with a
combination mechanical lock and electric
contact. They are to be used with existing
doors.
4) Attach door keeper and emergency key
plates to hoistway door.
The interlock:
•
•
•
Prevents the lift from running if the door
is not closed.
Prevents the door from being opened if
the platform is not at the landing.
Unlocks when the lift is on the landing
limit switch.
.
EMI Interlock
A length of multi‐conductor wire will
need to be ran from the bottom of the lift
tower to the interlock. Consult local
codes for type and mounting
requirements. After wiring is completed,
the wiring harness must be plugged into
it appropriate receptacle on the
controller (ref pg 5).
Wiring Connections
EMI
Black (A)
Black (B)
Lift Harness
Orange
Green
Yellow (C)
Yellow (D)
Black
Brown
1) Position interlock to door jamb and mark
mounting holes.
2) Fasten Interlock to door jamb with #8 wood
screws.
3) Route 4-conductor Interlock cable thru hole
in top of interlock and make wire
connections.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Fascia Panel (optional)
A fascia panel provides a smooth surface for the platform edge to run against to prevent any
shear or obstruction hazards and must be utilized.
A running clearance of no more than 3/4” and no less than 3/8” must be maintained between the
edge of the platform and the fascia panel.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Residential Platform Lift - Owners Section
LRead the manual thoroughly before operating the lift.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Congratulations on the purchase of your Harmar Vertical Platform Lift. This lift has
been engineered to provide trouble free service for many, many years. Please
read this manual completely before operating your lift.
Safety
• Do not exceed the maximum payload capacity of 600 lbs.
• Do not ride on the lift until it is anchored in place.
• This product is designed only for lifting people and wheel chairs. Do not use it for any other purpose.
• Make sure any obstructions are cleared from underneath the platform area before use.
• Make sure both the passenger and wheelchair are completely on to the platform before using.
• Do not disable any safety equipment or switches supplied with this lift.
• Do not attempt to service the lift yourself. Contact your Harmar dealer for assistance.
• Do not allow children to operate or play around the lift.
• Read all instructions in this manual before installing or operation the lift.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Controls
Emergency Stop
In an emergency push this red button to stop
the lift. Pull out on the button to run.
Up
Controls upward movement of lift platform.
To move platform up, depress and hold the
upper half of the rocker switch. To cease
movement, release switch.
Down
Controls downward movement of lift
platform. To move platform down, depress
and hold the lower half of the rocker switch.
To cease movement, release switch.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Operating the Lift
Step 1 - Up
Step 3
Drive onto and stop in the middle of the
platform. Apply the brakes of your chair or
scooter.
Press and hold the UP rocker. The lift will
move in the up direction and stop when it
reaches the upper landing.
Warning: Always verify the lift’s
platform has stopped level with the
upper landing. If not contact your
Harmar Dealer for assistance.
Step 2
Verify that the emergency stop button is not
activated by giving it a quick pull out, away
from the side of the platform.
Step 4
Release the brakes on your chair or scooter
and drive off the platform.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Step 1 - Down
Step 3
Drive onto and stop in the middle of the
platform. Apply the brakes of your chair or
scooter.
Press and hold the DOWN rocker. The lift
will move in the down direction and stop
when it reaches the lower landing.
Warning: Always verify the lift’s
access ramp unfolds fully and rests
on the ground. If not contact your
Harmar Dealer for assistance.
Step 2
Verify that the emergency stop button is not
activated by giving it a quick pull out, away
from the side of the platform.
Step 4
Release the brakes on your chair or scooter
and drive off the platform.
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty Certificate
22
Please fill out all fields and return within 10 days of product purchase.
Harmar Summit, LLC., Attn: Warranty Department
2075 47th Street, Sarasota, FL 34234
_____
Harmar warrants to the original purchaser of a Highlander Residential vertical platform lift manufactured by us to be
free from defects in material, mechanical and electrical components (parts),excluding labor cost, batteries and paint,
for a period of one (1) year, provided that the products have been installed, maintained and operated properly.
This warranty starts on the date of the retail purchase, provided the warranty certificate is returned to Harmar,
completely filled out within ten (10) days of purchase. This warranty does not cover maintenance or adjustments.
Harmar will not be charged for labor, consequential damage or repair expenses. Harmar will not, under any
circumstances, be liable for the loss of the use of its products or loss of time. This warranty becomes null and void if
the product has been lost, damaged by accident, misused and/or neglected, or if the product has been modified in any
way. Defective parts must be returned, prepaid, to Harmar for inspection prior to credit or replacement. At Harmar’s
option, any part found to have been modified, over-stressed, damaged by accident, or misused is not covered by this
warranty.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, INCLUDING ALL IMPLIED
WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND THERE ARE NO
WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION OF THE LIMITED WARRANTY DESCRIBED HEREIN.
This Limited Warranty gives you specific legal rights, and you may have other rights which vary from state to state.
PRODUCT INFORMATION
Model:
PURCHASER INFORMATION
Name:
Serial No:
Address:
Purchase Date:
Phone:
INSTALLER INFORMATION
Email:
Account ID#:
Company Name:
Contact:
Address:
__
How did you hear about Harmar?
ꢀHarmar Dealer
ꢀMagazine
ꢀInternet
ꢀFriend or Acquaintance
ꢀSaw Harmar Product Somewhere
ꢀOther:
______
___
I purchased my Harmar lift because of:
Phone:
ꢀStyle/Appearance
ꢀEase of Use
Email:
ꢀPrice/Value
ꢀRecommendation
ꢀPrevious Experience
Please rate your satisfaction with your Harmar dealer:
ꢀGood ꢀFair ꢀPoor
ꢀExcellent
Download from Www.Somanuals.com. All Manuals Search And Download.
|