Installation & Operating Manual
P61A-2 Pellet Stove Owners Manual
Safety Testing by
ASTM E1509
Mobile Home Approved
ìCe manuel est disponible en FranÁais sur demandeî
R5
SAFETY NOTICE
PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALLAND USE YOUR NEW ROOM HEATER. FAILURE
TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY, OR EVEN DEATH.
FOR USE IN THE U.S. AND CANADA. SUITABLE FOR INSTALLATION IN MOBILE HOMES
IF THIS HARMAN STOVE IS NOT PROPERLY INSTALLED, A HOUSEFIRE MAY RESULT. FOR YOUR SAFETY,
FOLLOW INSTALLATION DIRECTIONS.
CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONSAND INSTALLATION INSPECTION
REQUIREMENTS IN YOUR AREA.
CONTACT YOUR LOCAL AUTHORITY (SUCH AS MUNICIPAL BUILDING DEPARTMENT, FIRE DEPARTMENT,
FIRE PREVENTION BUREAU, ETC.) TO DETERMINE THE NEED FOR APERMIT.
CETTE GUIDE D'UTILISATION EST DISPONIBLE EN FRANCAIS. CHEZ VOTRE CONCESSIONNAIRE DE HARMAN
STOVE COMPANY.
SAVE THESE INSTRUCTIONS.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Testing Lable
2
Assembly & Installation
Installation
4
5
Venting
6
Automatic Operation
ESP Control
Maintenance
Trouble Shooting
Feeder Parts
Specifications
Options
12
16
17
22
23
23
24
26
27
28
Wiring Diagram
Parts List
Warranty
Please read this entire manual before you install and use your new
room heater. Failure to follow instructions may result in
property damage, bodily injury, or even death.
SUITABLE FOR MOBILE HOME INSTALLATIONS.
Harman Stove Company
352 Mountain House Road
Halifax, PA 17032
P61A Pellet Stove 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly and Installation
Unpacking
The P61 is bolted to the skid to prevent movement
duringshipping.
To free the stove from the skid you must remove
the hold-down bolts in the rear of the pedestal base.
Removing or Installing rear cover panels
To remove the rear cover panels, loosen the
screws slightly and slide the covers outward as
shown in the illustration. To reinstall, simply slide
back into place and retighten the screws.
Firebrick
Install the firebrick vertically on the angle above
the burnpot.
Flame Guide
Install the cast iron flame guide on top of the
burnpot and make sure it is fully seated against the
augeropening. Thebottomoftheflameguideismarked
38+.
Shipping Bolts
Note: These same holes
are used for mobile home
installation
Rear Cover
Panels
Fig. 2
DO NOT INSTALLAFLUE DAMPER IN THE
EXHAUST VENTING SYSTEM OF THIS
UNIT.
WARNING
DO NOT INSTALLIN SLEEPINGROOM
DO NOT CONNECT THIS UNIT TO A
CHIMNEYFLUE SERVINGANOTHER
APPLIANCE.
CAUTION
THE STRUCTURAL INTEGRITY OF THE
MOBILE HOME FLOOR, WALL,AND
CEILING/ROOFMUST BE MAINTAINED.
INSTALLVENTAT CLEARANCES
SPECIFIED BYTHE MANUFACTURER
Mobile home installation should be done in
accordance with the Manufactured Home and
Safety Standard (HUD), CFR 3280, Part 24.
CAUTION
KEEPCOMBUSTIBLE MATERIALS
(SUCHAS GRASS, LEAVES, ETC.)AT LEAST 3
FEETAWAY FROMTHE FLUE OUTLETON
THE OUTSIDE OF THE BUILDING.
4
P61A Pellet Stove
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installing
Place the stove on a noncombustible floor protector
9"-13"
that extends 6 inches to the front, 6 inches to the sides
and 1 inch to the rear of the stove. The minimum floor
protector material is 24 gauge sheet metal.
Place the stove away from combustible walls at least
as far as shown in figures 3,4 and 5. Please note the
difference in side wall clearance with and without side
shields.
FLOOR
PROTECTOR
9"-13"
Note that the clearances shown are minimum for
safety but do not leave much room for access when clean-
ing or servicing. Please take this into account when plac-
ing the stove.
9" With Side Shields
13" Without Side Shields
Fig. 3
Connect the power cord to a 120 V.A.C. 60Hz
grounded receptacle. (A surge protector is recommened
to protect the circuit board).
1"
2"
Prior to installing the flue pipe, connect a draft meter
to the stove as shown in fig. 6. (The draft meter must
have a minimum range of 0-.5). However, prior to taking
the draft reading be sure all doors and windows in the
home are closed. Record the draft reading_______. If
this reading is more than .05" lower than the unconnected
reading, check for possible restrictions or the need for
outside air (see page 7).
12"
6"
6"
6"
Mobile Home Installation
FLOOR PROTECTOR
When installing this unit in a mobile home several re-
quirements must be followed:
Fig. 4
1. The unit must be bolted to the floor. This can be
done with 1/4" lag screws through the 2 holes in the base
plate.
2. The unit must also be connected for the outside air.
See page 8.
3. Floor protection and clearances must be followed
as shown.
4. Unit must be grounded to the metal frame of the
mobile home.
CAUTION: This appliance must be vented to the out-
side.
Due to high temperatures, the stove should be placed
out of traffic and away from furniture and draperies.
Children and adults should be alerted to the hazards of
high surface temperatures and should stay away to avoid
burn to skin and/or clothing.
18"
FLOOR PROTECTOR
Fig. 5
Young children should be carefully supervised when
they are in the same room as the stove.
Clothing and other flammable materials should not be
placed on or near this unit.
Installation and repair of this Harman Stove should be
done by a qualified service person. The appliance should be
inspected before use and at least annually by a qualified
service person. More frequent cleaning will be required. It
is imperative that control compartments, burners, and circu-
lating air passageways of the stove be kept clean.
P61A Pellet Stove 5
Fig. 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Venting
Requirements for Terminating the Venting
WARNING: Venting terminals must not be re-
cessed into a wall or siding.
I. The clearance to service regulator vent outlet
must be a minimum of 6 feet.1
J. The clearance to a non-mechanical air sup-
ply inlet to the building or the combustion air inlet to
any other appliance must be a minimum of 48î.1
K. The clearance to a mechanical air supply
inlet must be a minimum of 10 feet.1
NOTE: Only PL vent pipe wall pass-throughs
and fire stops should be used when venting through
combustible materials.
NOTE: Always take into consideration the ef-
fect the prevailing wind direction or other wind cur-
rents will cause with flyash and /or smoke when plac-
ing the termination.
In addition, the following must be observed:
A. The clearance above grade must be a mini-
mum of 18".1
B. The clearance to a window or door that may
be opened must be a minimum of 48" to the side,
48" below the window/door, and 12" above the win-
dow/door.1
(with outside air installed, 6 feet )
L. The clearance above a paved sidewalk or a
paved driveway located on public property must be
a minimum of 7 feet.1,2
M. The clearance under a veranda, porch, deck
or balcony must be a minimum of 12 inches.1,3
NOTE: The clearance to vegetation and other
exterior combustibles such as mulch is 36î as mea-
sured from the center of the outlet or cap. This 36î
radius continues to grade or a minimum of 7 feet
below the outlet.
1Certain Canadian and or Local codes or regu-
lations may require different clearances.
2A vent shall not terminate directly above a side-
walk or paved driveway which is located between
two single †family dwellings and serves both dwell-
ings.
3Only permitted if veranda, porch, deck, or bal-
cony is fully open on a minimum of 2 sides beneath
the floor.
( with outside air installed, 18î )
C. A 12" clearance to a permanently closed
window is recommended to prevent condensation
on the window.
D. The vertical clearance to a ventilated soffit
located above the terminal within a horizontal dis-
tance of 2 feet (60 cm) from the center-line of the
terminal must be a minimum of 18".
E. The clearance to an unventilated soffit must
be a minimum of 12".
F. The clearance to an outside corner is 11"
from center of pipe.
NOTE: Where passage through a wall, or
partition of combustible construction is desired,
the installation shall conform to CAN/CSA-B365.
(if in Canada)
G. The clearance to an inside corner is 12".
H. A vent must not be installed within 3 feet (90
cm) above a gas meter/regulator assembly when
measured from the horizontal center-line of the regu-
lator.1
Inside Corner
Detail
Fixed
Closed
Fixed
Closed
Openable
Openable
= Air supply inlet
= Vent terminal
= Area where terminal is not permitted
A
V
6
P61A Pellet Stove
Download from Www.Somanuals.com. All Manuals Search And Download.
Venting
Venting
IMPORTANT NOTICE
A combustion blower is used to extract the com-
Pellet Vent Pipe or PL Vent Pipe Must be used.
bustion gases from the firebox. This causes a negative
pressure in the firebox and a positive pressure in the
venting system as shown in fig. 7. The longer the vent
pipe and more elbows used in the system, the greater
the flow resistance. Because of these facts we recom-
mend using as few elbows as possible and 15 feet or
less of vent pipe. The maximum horizontal run should
not exceed 48". If more than 15 feet of pipe is needed,
the diameter should be increased from 3" to 4" because
a larger pipe causes less flow resistance. Be sure to
use approved pellet vent pipe wall and ceiling pass
through fittings to go through combustible walls and
ceilings. Be sure to use a starting collar to attach the
venting systen to the stove. The starting collar must
be sealed to the stove with high temp silicone
caulking.
Vent Pipe
Pellet venting pipe ( also known as PL vent ) is
constructed of two layers with air space between the
layers. This air space acts as an insulator and reduces
the outside surface temperature to allow a clearance to
combustibles of only 3inches. The sections of pipe lock
together to form an air tight seal in most cases; however,
in some cases a perfect seal is not achieved. For this
reason and the fact that the P61 operates with apositive
vent pressure we specify that the joints also be sealed
with clear silicone.
Fig. 7
+ = Positive static pressure
= Negative static pressure
Outside Air
Outside air is optional except in mobile homes and
where building codes require. The benefit of outside air
is mainly noticed in small very tight houses.
Outside air flex pipe
goes here
To install outside air use 2 3/8" I.D. flex pipe part
number 2-00-08543. There is a break-away hole on
the rear panel which must be removed before connect-
ing the flex pipe. The pipe should be run outside and
terminate to the side or below the vent pipe outlet so the
flueoutletismorethan12"fromtheinletcover.Themaxi-
mum length run of this pipe is 15 feet. If a longer run is
needed the size must be increased to 3". Inlet cover part
number 1-10-08542 should be used to keep birds, ro-
dents etc. out of the pipe.
Flex pipe part#
2-00-08543
.
HRV
When installing in ahouse with aHeat Reclaiming
Ventilation System (HRV) be sure the system is balanced
and is not creating a negative pressure in the house.
P61A Pellet Stove 7
Inlet Cover part#
1-10-08543
Download from Www.Somanuals.com. All Manuals Search And Download.
Venting
#1 Preferred method
This method provides excellent venting for normal
operation and allows the stove to be installed closest to
the wall.Two inches from the wall is safe; however, four
inches allows better access to remove the rear panel.
The vertical portion of the vent should be three to five
feet high. This vertical section will provide natural draft
in the event of a power failure.
Fig. 8
3 ft.
to combustibles
#2 Preferred method
This method also provides excellent venting for
normal operation but requires the stove to be installed
farther from the wall. The vertical portion of the vent
should be three to five feet high and at least three inches
from acombustible wall. This vertical section will pro-
vide natural draft in the event of a power failure.
If the stove is installed below grade be sure the
vent termination should be at least 1 foot above grade.
CAUTION
Keep combustible materials (such
as grass, leaves, etc.) at least 3 feet
away from the flue outlet on the outside
of the building.
3 ft.
to combustibles
Fig. 9
8
P61A Pellet Stove
Download from Www.Somanuals.com. All Manuals Search And Download.
Venting
#4 Installing into an existing
chimney ( US only )
This method provides excellent venting for normal
operation. This method also provides natural draft in
the event of apower failure. If the chimney condition is
questionable you may want to install aliner as in method
#7.
Fig. 10
#5 Installing into an existing
fireplace chimney ( US only )
This method provides excellent venting for normal
operation. This method also provides natural draft in
the event of a power failure.
The damper area must be sealed with a steel plate
or fiberglass. A cap should be installed on the chimney
to keep out rain. If the chimney condition is question-
able you may want to install aliner all the way to the top
as in method #6.
Fig. 11
P61A Pellet Stove 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Venting
#6 Installing into an existing
fireplace chimney ( US and
Canada )
This method provides excellent venting for normal
operation. This method also provides natural draft in
the event of a power failure.
In Canada and some places in the US it is required
that the vent pipe extend all the way to the top of the
chimney.
In this method acap should also be installed on the
chimney to keep out rain. Be sure to use approved pel-
let vent pipe fittings. Seal pipe joints with silicone in ad-
dition to the sealing system used by the manufacturer.
Pipe size should be increased to 4" using this method.
Fig. 12
#7 Installing into an existing
chimney ( US and Canada )
This method provides excellent venting for normal
operation. This method also provides natural draft in
the event of a power failure.
In Canada and some places in the US it is required
that the vent pipe extend all the way to the top of the
chimney. The pipe or liner inside the chimney should be
4"diameter.
In this method acap should also be installed on the
chimney to keep out rain. One disadvantage of this
method is that it is harder to clean the vent pipe, there-
fore, there is a tendancy not to do it as often as needed.
Fig. 13
10 P61A Pellet Stove
Download from Www.Somanuals.com. All Manuals Search And Download.
Venting
Storm collar
Flashing
12" min.
3" min.
3" min.
3" min.
PL vent manufacturer's
firestop spacer and support
No insulation or
other combustible
materials are
allowed within 3"
of the PL vent pipe.
Minimum flue vent
configuration
It is recommended that
outside air be installed with this
ventingconfiguration.
(See Page 9 for
c
o
r
n
e
r
i n s t a l l a t i o n
clearances)
Fig. 14
#8 Installing through the ceiling vent
Through the ceiling vent, follow PLvent
manufacturers recommendations when using wall and
ceiling pass through.
Fig. 15
Fig. 16
P61A Pellet Stove 11
Download from Www.Somanuals.com. All Manuals Search And Download.
P61A-2 AUTOMATIC IGNITION/OPERATION
The P61A pellet stove is more than just automatic ignition, it is also automatic temperature control.
The automatic system will allow the fire size to be adjusted to match the heating needs and even put
the fire out if necessary. If heat is needed after the fire is out, the P61Awill automatically re-ignite
and adjust the fire size to match the heating need. The totally automatic room sensor mode is
recommended because of its efficiency.
o
o
The unit can be switched between "AUTO" and "MANUAL" at any time during operation.
Ignitor switch to "AUTO"
Room Temperature Mode
In "Room Temp Mode" heat output is controlled auto-
matically by the Room Sensing Probe. When the Room Sens-
ing Probe calls for heat, the stove will increase output. When
the Room Sensing Probe is getting close to the set tempera-
ture, the stove will begin to level off output and keep the fire
burning at just the right temperature to maintain that setting.
High output is determined by the feed rate setting.
This setting, generally on #4, can be increased if higher burn
rates are necessary. The unit's maximum burn rate should not
create less then 1" of ash on the burn pot front edge. See
Fig.2. Overfeeding is not a safety concern, but fuel may be
Room Temperature Mode: This setting will produce a room
temperature of 70 degrees with the distribution blower at
medium speed.
wasted if unburned pellets fall into the ash pan.
In "RoomTemp Mode" aconstant fuel consumption rate
is sacrificed for exact room temperature. Therefore, as it gets
colder more pellets will be burned automatically.
The distribution blower speed will vary according to the
position of the mode selector pointer, and fire size.
Ignitor switch to "AUTO"
Stove Temperature Mode
Stove Temperature Mode
Thisallowsforautomaticignitionuponstart-uponly.The
unit can then be set at any desired setting. The heat output
and fuel consumption will remain constant regardless of room
temperature. The unit's maximum feed rate should not create
less than 1" of ash on the burn pot front adge. See Fig 2.
The unit's low burn or maintenance setting is as low as it
will go. It will not go out unless it runs out of fuel or is turned
off.
This setting will produce medium heat with the
distribution blower on "low".
Shut-Down Procedure
To kill the fire or stop burning the stove, turn the Mode
Selector to "OFF". This will cause the fire to diminish and
burn out. When the fire burns out and the stove cools down
everything will stop.
If you pull the plug to shut down the stove, all motors
will stop. This may cause incomplete combustion and smoke
in the firebox. If the load door is opened the smoke may es-
cape.
This setting will produce continuous maximum heat output
with the distribution blower at full speed.
The best way to shut down the stove is simply let it run
out of pellets, then the stove will shut down automatically.
12 P61A Pellet Stove
Download from Www.Somanuals.com. All Manuals Search And Download.
P61A-2 AUTOMATIC START UP
Starting First Fire
Ignitor Switch to"AUTO"(up position)
Make sure the unit is plugged into a 120
VAC, 60 HZ electrical source. The power light
should be the only light lit.
See Note 7.
1"
Fig. 17
NOTICE:
When power is given to the stove, the control board
will blink afew times to indicate current version of
control board.
1. Turn Mode Selector to "OFF".
2. Fill hopper with pellets.1
3. Clean burn pot with scraper, if necessary.5
4. If starting after an empty hopper, turn
Feed Adjuster to "TEST" (for one 60 second
cycle).2 This will purge pellets into the auger
tube and also allow you to check the motors
for operation. NOTE: The auger motor will
not operate with the view door or ash pan
door open.3
Fig. 18
1. Fines are small pieces of broken pellets (sawdust). Fines do not
flow easily and often build up on the hopper funnel bottom angles.
These fines can be pushed into the feeder opening and then fill the
hopper with pellets. As the system works, they will be burned.
2. The "TEST" cycle will operate the feeder motor for exactly one
minute. Turning to "TEST" again and again may purge too much
fuel into the burn pot causing excessive smoke on start-up.
3. The firebox low pressure switch will not allow the auger motor
or the igniter element to operate if the view door or the ash pan
door are open.
5. Turn Feed Adjuster to #4.4
4. Adjust Feed Rate. If this is your first fire or you are trying different
pellets, set the feed adjuster to #4, Fig. 17. This is a conservative
number and will probably need to be increased. After you know a
6. Flip the Ignitor Switch up into the "AUTO"
feed rate setting that works well, use that setting. Remember, if position.
your feed rate is too high you may waste fuel.
7. Turn the Temperature Dial to desired room
5. This is usually a weekly maintence procedure. Cleaning the
burn pot with the scraper with a small amount of new fuel in the
bottom is not a problem. First, scrape the ashes on the front of the
burn pot into the ash pan. Then scrape the holed surface downward
into the burn pot. When the stove is ignited these scrapings will be
pushed out by the feeder.
6. The ash pan can hold the ashes from approximately 1 ton of
premium fuel. This means the ashes will only need to be emptied a
few times a year.
7. Setting the feed adjuster # for maximum burn: With the unit
burning in "AUTO", turn to "Stove Mode" and put the fan on "H".
Set the Temperature Dial to #7. Allow the unit to burn for about
30 minutes and check ash on front of burn pot. Fig. 18. If the ash
line is larger than 1", turn the feed adjuster from #3 to #4. Allow
another 30 minutes of burn time and check again. If , at #6 setting,
a 1" or less ash bed is not obtainable, it is not a problem. The 1"
ash bed is only a maximum burn rate and at most normal settings
the ash bed will be larger.
temperature.
8. Turn Mode Selector to Room Temperature
or Stove Temperature.
9. Fill hopper with pellets and remove ashes
as required.6
Warning
"NEVER USE GASOLINE, GASOLINE-TYPE LANTERN
FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR
SIMILAR LIQUIDS TO START OR "FRESHEN UP"AFIRE
IN THIS HEATER. KEEPALLSUCH LIQUIDSWELLAWAY
FROM THE HEATER WHILE IN USE".
P61A Pellet Stove 13
Download from Www.Somanuals.com. All Manuals Search And Download.
P61A-2 MANUAL IGNITION/OPERATION
The P61A Pellet Stove is capable of manual operation. This also allows the operator to
manually control operation during an emergency (i.e. ignitor failure, when using a 502H battery
backup, or when using certain generators.)
o
The unit can be switched between "AUTO" and "MANUAL" at any time during operation.
o
NOTE: When starting the unit in the "AUTO"
mode and switching to "MANUAL", the fire must be
large enough to start the distribution blower. The start-
ing of the blower is a signal that the start cycle is com-
pleted and the fire will not go out.
Ignitor Switch to "MANUAL"
Room Temperature Mode
The fire will have to be lit with starting gel and amatch,
or started automatically, see "Automatic Operation". Turn
to "Manual" position when the fire is established.
The difference between "AUTO" RoomTemperature
Mode and "Manual" Room Temperature Mode is that the
fire will not go out as the room temperature goes above the
control board setting. The unit can only go to low burn and
will remain there until it runs out of fuel or until more heat is
needed and the feed rate increases. Feed rate adjustments
Room Temperature Mode: This setting will produce a room
temperature of 70 degrees with the distribution blower at
medium speed.
Manual Stove Temperature Mode and dial settings are the same as "AUTO" settings.
Ignitor Switch to "MANUAL"
Stove Temperature Mode
The advantage of this mode is to allow the operator to
have alarge viewing fire without blowing extra heat into the
room.
During operation, with the temperature dial set at #5
or less, the distribution fan will not operate. A #5 on the
temperature dial and a #5 on the feed adjuster is approxi-
mately 80% output. It is not necessary to operate the distri-
bution blower below this point. Therefore, there can be a
O
O
higher feed rate (alarger viewing fire) without an excess of
hot air blowing into the room.
An example of when to use the Manual Stove Tem-
perature Mode is if you want to watch a large fire and the
room is aleady up to temperature. The Stove Temperature
Mode allows you to have a larger fire and a lower sound
level, without the distribution blower.
NOTE: During the use of this mode, if you keep
increasing the temperature dial setting to increase the
fire size, the distribution blower will automatically come
on when the ESPTemperature reaches 350o F, or 81%
output.
This setting will produce a large viewing fire without
a distribution blower operating.
14 P61A Pellet Stove
Download from Www.Somanuals.com. All Manuals Search And Download.
P61A-2 MANUAL START UP
Starting First Fire
Fig. 20
Ignitor Switch to"MANUAL"
(down position)
Make sure the unit is plugged into a
120 VAC, 60 HZ electrical source. The
power light should be the only light lit.
Fig. 19
See Note 7.
1"
1. Turn FEED ADJUSTER to desired feed
rate. No. 4 is good for most pellets.4
2. Turn the MODE SELECTOR to ìOFFî
and then to the desired mode. This will
reset control and start the combustion mo-
tor.
Fig. 21
3. Turn the TEMPERATURE DIAL to the
desired setting.
1. Fines are small pieces of broken pellets (sawdust). Fines do not
flow easily and often build up on the hopper funnel bottom angles.
These fines can be pushed into the feeder opening and then fill the
hopper with pellets. As the system works, they will be burned.
2. The "TEST" cycle will operate the feeder motor for exactly one
minute. Turning to "TEST" again and again may purge too much
fuel into the burn pot causing excessive smoke on start-up.
3. The firebox low pressure switch will not allow the auger motor
or the igniter element to operate if the view door or the ash pan
door are open.
4. Adjust Feed Rate. If this is your first fire or you are trying different
pellets, set the feed adjuster to #4, Fig. 19. This is a conservative
number and will probably need to be increased. After you know a
feed rate setting that works well, use that setting. Remember, if
your feed rate is too high you may waste fuel.
4. Clean burn pot with scraper if necessary.5
5. Fill burn pot with pellets, only level with
front edge. (Do Not Over Fill).
6. Add starting gel on top of the pellets. Stir
gel into pellets for fast lighting.
7. Light starting gel with a match, and close
the door. Operation will begin when the fire
reaches the proper temperature.3
8. Fill hopper with pellets and remove ashes
as required.1, 6
5. This is usually a weekly maintence procedure. Cleaning the
burn pot with the scraper with a small amount of new fuel in the
bottom is not a problem. First, scrape the ashes on the front of the
burn pot into the ash pan. Then scrape the holed surface downward
into the burn pot. When the stove is ignited these scrapings will be
pushed out by the feeder.
6. The ash pan can hold the ashes from approximately 1 ton of
premium fuel. This means the ashes will only need to be emptied a
few times a year.
Warning
7. Setting the feed adjuster # for maximum burn: With the unit
burning in "AUTO", turn to "Stove Mode" and put the fan on "H".
Set the Temperature Dial to #7. Allow the unit to burn for about
30 minutes and check ash on front of burn pot. Fig. 21. If the ash
line is larger than 1", turn the feed adjuster from #3 to #4. Allow
another 30 minutes of burn time and check again. If , at #6 setting,
a 1" or less ash bed is not obtainable, it is not a problem. The 1"
ash bed is only a maximum burn rate and at most normal settings
the ash bed will be larger.
"NEVER USE GASOLINE, GASOLINE-TYPE LANTERN
FUEL, KEROSENE, CHARCOAL LIGHTER FLUID, OR
SIMILAR LIQUIDS TO START OR "FRESHEN UP"AFIRE
IN THIS HEATER. KEEPALLSUCH LIQUIDSWELLAWAY
FROM THE HEATER WHILE IN USE".
P61A Pellet Stove 15
Download from Www.Somanuals.com. All Manuals Search And Download.
P61A-2 AUTOMATIC IGNITION ESP CONTROL
Power Light
Indicates power to the
control.
Feed adjuster
Sets the maximum feed
rate
Test
Runs all motors at full
speed for one minute
to check operation.
After two minutes the
stove will go to
minimum burn and the
blowers will alternate
from high to low every
minute to remind you
that you are still in
"Test Mode".
Status Light
Will be lit in either stove or
room temp mode when
pointer is not within off
position band except after
normal shut down. Blinks
to indicate errors listed
below.
O
O
Ignitor switch
Set to appropriate
Start-Up mode.
Indicates power to
distribution blower.
Distribution Blower speed
adjustment range.
L = low
Indicates power to
combustion blower
H = high
Variable speed anywhere
Indicates power to the
feed motor.
between
L
and H;
although as the stove
temp. goes up , so does the
L and H scale.
Indicates ignitor is on.
Mode Selector
Allows you to choose between
Room Temp Mode, Stove Temp
Mode, or OFF. Also allows you
to vary the distribution blower
speed by turning the knob to
the high or low side of each
mode.
Temp dial
Dealer Diagnostic Port
For dealer maintenance
only. Requires special DDM
monitor supplied to Harman
Dealers exclusively.
Allows you to adjust the room temperature in Room Temp
Mode using the outer scale marked in degrees Fahrenheit.
It also allows you to adjust the stove temperature while in
Stove Temp Mode using the inner scale marked from 1 to 7.
Status light error messages:
1Blink: Indicates control board self diagnostic failure.
This requires amanual reset*.
2 Blinks: Indicates that the jumper (J2) on the rear of
the control board is not connected. Without this jumper
the unit will only burn at minimum rate.
3 Blinks: Indicates ESP (Exhaust Sensing Probe) fail- then back on to the desired mode. If the unit was not
ure. This requires a manual reset*.
4 Blinks: Can occur only in Room Temp Mode and
indicates Room Sensing Probe failed or not installed. If
a Room Sensing Probe is then installed, the status light
will automatically reset.
6Blinks :Indicates that the control has calculated poor
or incomplete combustion occurring for more than 50
minutes.
A six blink status may be set if the stove is allowed to
run out of pellets. To reset, turn mode selector to "OFF"
out of pellets, seeTroubleshooting section for more de-
tails.
* Manual reset- disconnect power cord for a few sec-
onds and reconnect. If error still occurs call your Dealer.
NOTICE: When power is given to the stove, the con-
trol board will blink afew times to indicate current ver-
sion of control board. This should not be confused with
error messages.
5 Blinks (In Igniter Auto. Mode Only): Indicates
that the unit has failed to light within the 36 minute start
cycle. To reset - Turn Mode Selector to "OFF", then
16 tuPr6n1tAo ePietlhleetrSmtoovdee again.)
Download from Www.Somanuals.com. All Manuals Search And Download.
P61A-2 Low Draft Voltage Adjustment
C o m b u s t i o n
Motor Speed
Control
Low draft only
set point.
The small straight
screwdriver slot is
plastic; therefore,
the unit can be
adjusted while in
operation.
Draft Meter bolt
hole location
On a P61A
the draft hole is under
the left rear corner of
the firebox.
Fig. 23
Fig.22
Fig.1
Low Draft Voltage Adjustment
A simple draft test should be performed after
completing the flue pipe installation.To record the results for
future reference:
These units are pre-tested at the factory with exactly
120 VoltsA.C., 60 Hz. They are checked and adjusted for
firebox tightness, gasket leakage, motor operation and ignitor
operation. The P61A is then factory set at a mid-point
adjustment and in most cases will not need any adjustments.
NOTE: The factory low draft setting may not be correct
for the units permanent installation conditions.
The control board on the P61A is equipped with a
low draft adjustment port. Located on the control face just
to the right of the igniter light. This voltage adjustment is
provided to allow the unit to be adjusted for the household
voltage where the unit is going to be in permaneant operation.
NOTE: The line voltage varies from area to area and often
home to home.
The low draft voltage should be adjusted to achieve
the most efficient burn on low burn or "maintenance". This
voltage adjustment allows the installer to change the low
voltage set point approximately 10 volts. This adjustment
should be done by the installer during set up because adraft
meter reading is required to insure proper set up.
1. Plug unit into a 120VAC, 60 HZ outlet.
2. Close the hopper lid, front view door, and the ash pan.
Neither pellets or a fire are required for this test.
3. With the mode selector in the "OFF" position, turn the
feed adjuster to "TEST".
4. Record the high draft_____in W.C. (Normal is -.50 to -
.60) The control will be on the High Draft for a total of 2
minutes.
5. After 2minutes is up, the combustion motor will go down
tolowdraftandthedistributionblowerwillgoonhigh. Allow
approximately 15 seconds to pass for the combustion motor
to slow before checking the low draft.
6. If the low draft is between -.35 and -.45, record the
reading _____ in W.C. If the reading is higher, slowly turn
the set screw counter-clockwise until the draft lowers. If the
reading is lower, very slowly turn the set screw clockwise
until the draft increases.
NOTE: The test mode alternates from high to low draft
every 60 seconds. If more time is needed for draft
adjustment, wait until the next low draft cycle.
NOTE: In some cases, the draft may not go as low as
-.35 to -.45 even with the set screw completely counter-
clockwise.
If the unit is not adjusted properly, it does not cause
asafety concern. If the unit is adjusted too high, only effiency
is lost. If the unit is adjusted too low, the low draft pressure
switch will not allow the feeder motor or the igniterto operate.
P61A Pellet Stove 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Room Sensor and Rear Shield Installation
Rear Shields
Room Sensor Installation
5/16" Hex
Head
Screws (2
on each
side)
5/16" Hex Head
Screws (2 on
each side)
Fig. 24
Fig. 25
The room sensor is a small temperature sen-
sor on the end of a 60" gray wire. This sensor is
installed much like a standard wall thermostat. Be-
cause it is so small, it can be hidden along the trim
of a doorway or even up the leg of a coffee table.
There is a remote room sensor port on the rear of
the unit for easy external connection. Use standard
18-2 thermostat wire to extend the distance to the
desired location (100' maximum). The room sen-
sor should be installed in the location where you want
to control the temperature.
The rear isolated shields are split in the middle for
easy removal. Each shield has two 5/16" hex head
screws that only need to be loosened (NOT
REMOVED) to allow the shield to slide away from
the unit. NOTE: It is not recommended that the
unit be operated with the shields removed, due
to the hot and moving parts which they protect.
NOTE: Distances of more than 25 feet from
the unit or in another room are not recommended.
The room sensor is essential for the P61A's excel-
lent efficiency.
NOTE: It is recommended that the room
sensor be installed, even if only installed on the
rear of the unit as a return air sensor.
18 P61A Pellet Stove
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Removing Ashes:
When approximatly 1 ton of pellets has been
burned it will be necessary to empty the ash pan.
Ashes should be placed in a metal container
with a tight fitting lid. The closed container of
ashes should be placed on a noncombustible
floor or on the ground, well away from all com-
bustible materials, pending final disposal. If ashes
are disposed of by burial in soil or otherwise lo-
cally dispersed, they should be retained in the
closed container until all cinders have thoroughly
cooled.
It is recommended that the stove is cold and
shut down when removing ash pan.
1. Pull on latch handle and remove ash pan as
shown at left. Use ash pan handle to carry and
dispose of ashes.
2. Slide the ash pan back into the stove and latch
by pushing in on latch handle.
Blower Cover
Latch
Combustion
Blower Cover
Fig 26
Cleaning:
The stove will need to be cleaned for approxi-
mately every 2to 5tons of pellets burned. The amount
of pellets burned before cleaning will vary depending
on the brand of pellets.
Heat Exchanger Fins
1. Shut down stove and disconnect power cord to
insure that all motors are stopped.
2. Remove ash pan as described earlier.
3. Remove combustion blower cover by turning the
blower cover latch vertical as shown in Fig.26
and sliding the cover out of the slot on the
left.This will expose the combustion blower
wheel and flue outlet, Fig.27.
4. Clean the blower wheel with a brush and a
vacuum cleaner.
Scraper
5. Use a brush to clean the flue, being careful not to
damage the ESP probe. The flue goes straight
through into the vent pipe (Fig.27) therefore, the
vent pipe can also be cleaned to some extent
through the flue outlet.
Flue Outlet
Blower Wheel
Blower Cover
Latch
6. Reinstall blower cover and relatch.
Fig 27
P61A Pellet Stove 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Clean-out plate
7. Open burn pot clean-out as shown to the left,
clean fly ash from burn pot and replace cover.
8. Clean heat exchanger with scraper as shown in fig
25.
9. Brush or scrape the inside of the stove to remove
flyash.
10. Scrape burnpot with flat end of scraper provided
with the stove. Fig. 33.
Fig. 28
Fig. 29
Latch "closed "with
blower cover in place.
Burn pot clean-out is
closed.
Latch "open "with blower
cover partly removed.
Burn pot clean-out is
open.
11.Slide ash pan into stove and latch into place.
Brush not
supplied. Can be
found in hardware
ESP probe
stores.
Fig. 32
Soot and Fly Ash
The products of combustion will contain small
particles of fly ash. The fly ash will collect in
theexhaustventingsystemandrestricttheflow
of the flue gases. Incomplete combustion,
such as occurs during startup, shutdown, or
incorrect operation of the room heater, will
lead to some soot formation which will
collectintheexhaustventingsystem. The
exhaust venting system should be in-
spected at least once every year to de-
termine if cleaning is necessary.
Fig. 30
Exposed blower wheel
and flue opening,
NOTE: ESP probe is
visible.
Blower cover
removed.
ESP Probe
Be careful not to
damage ESP probe
when cleaning with
brush.
Fig. 33
Fig. 31
20 P61A Pellet Stove
Download from Www.Somanuals.com. All Manuals Search And Download.
P61A-2 Maintenance - Burn Pot
Burn Pot Cleaning and Maintenance
1. Scrape the top holed surface and sides of the burn
pot.(Fig 34) It is not necessary to completely remove
all material from the burn pot. The excess will be
pushed out during the next use.
2. Loosen the (2) wing thumb screws on the lower
front angle of the burn pot. (Fig. 34)
3. Lift off the clean-out cover (Fig.35) to open the
bottom clean-out chamber. (Fig.36)
DANGER
Disconnect the power to the unit before
removing cover.
Fig. 34
4. Clean ash buildup from inside the chamber while
cover is off. Use the scraper to tap on the top front
edge of the burn pot. This will help knock pieces of
ash, loosened by the scraping process, down through
the holes. It also helps knock scale off of the ignitor
element.
Figure 36
The ignitor is made to be removable for service
by insulated male/female wire connectors. These
connections between the hot leads (the wires inside
the burn pot) and the cold leads (the wires from the
control board) are always pulled to the inside rear of
the feeder body. (Not coiled inside the burn pot.)
It is very important that these connections are
to the inside rear of the feeder body.Also, the extra
wire of the ignitor wire service loop must be pulled out
through the rear of the feeder and tied up so that it will
not be damaged by any moving parts.
Fig. 35
DANGER
Disconnect the power to the unit before
removing cover.
Burn pot ignitor
Warning
Use caution when cleaning burn pot clean-out
chamber. Do not damage the high temperature
igniter wires.
Ignitor hot lead wires
(high temperature)
Note: The hot lead/cold lead
connection must always be pulled
to the rear of the feeder body
before operation.
Fig. 36
Viewed from below throught the ash pan opening.
P61A Pellet Stove 21
Download from Www.Somanuals.com. All Manuals Search And Download.
P61A-2 Trouble-Shooting
5. Power failure or blown fuse.
FEEDER DOES NOT FEED
1. No pellets in hopper.
SMOKE IS VISIBLE COMING OUT OF VENT
1. Air-fuel ratio is too rich.
2. Firebox draft may be too low for low draft pressure
switch in feeder circuit to operate. Check for closed
doors, loose or missing gasket on doors or hopper lid,
faulty pressure switch.
A. Feed rate too high.
B. Draft too low caused by a gasket leak.
3. Feed motor will not run until ESP
senses 165 deg. F. Maybe you did not put
enough pellets in the burn pot before lighting the fire.
4. Something is restricting flow in the hopper or caus-
ing the slide plate to stick.
LOWHEAT OUTPUT
1. Feed rate too low
2. Draft too low because of gasket leak.
3. Poor quality or damp pellets
4. Combination of 1. and 2.
5. Feed motor has failed.
PARTIALLYBURNED PELLETS
1. Feed rate too high.
Helpful Hints
Cleaning Burn Pot
2. Draft too low. (Check burn pot clean out slide and
door gasket).
3. Burn pot or heat exchanger tubes may need to be
cleaned.
Whenever your stove is not burning, take the op-
portunity to scrape the burn pot to remove carbon
buildup. Avacuum cleaner is handy to remove the resi-
due. Be sure the stove is cold if you use a vacuum.
Carbon buildup can be scraped loose with the fire
burning using the special tool provided with your stove.
Scrape the floor and sides of the burn pot. The carbon
will be pushed out by the incoming fuel. Always wear
gloves to do this.
4. Combination of all the above.
5. #6 status blink: A 6 blink control board status indi-
cation is caused by poor or incomplete combustion.
TheAutomatic Ignition circuit board has the ability to
track the combustion through feed settings and ESP
temperatures. When the control board has calculated
poor or incomplete combustion it will shut down the
unit as a safety feature. (Poor or incomplete combus-
tion is a contributer of creasote which may cause a
chimneyfire)
A 6 blink status may be caused by several things:
1. Blocked or partially blocked flue.
2. Blocked or partially blocked inlet air.
a. backdraft damper on the inlet pipe may be stuck
closed.
Removing Ashes
Turn the Temp Dial to number 1 approximately
30 minutes before removing ashes. This will result in a
cooler stove and ash pan.
Maximum Feed Adjuster settings are not needed
in most cases. Operating in the normal range (#4) is
recommended when maximum heat output is not re-
quired. The ESP probe prevents the stove from being
over-fired.
b. if outside air is installed the inlet cover may be
blocked.
Keep the stove free of dust and dirt.
3. The air chamber under the burnpot may be filled
with fines and small bits of ash.
4. The holes in the burnpot may be getting filled with
ash or carbon buildup.
5. Combustion blower fan blades may need cleaned.
6. No fuel in hopper.
Fuel
Pellet fuels are put into 3categories in terms of ash
content. Premium at 1% or less, Standard at 3% or less
and all others at 3% or more.
SMOKE SMELL
The P61A is capable of burning all 3categories of
pellets due to a patented feeder and burn pot system.
It should be noted, however, that higher ash con-
tent will require more frequent ash removal and may
provide less BTU's per pound. Normally, standard and
high ash pellets cost less than premium pellets and can
be cost effective when burned in the P61A.
Seal the vent pipe joints and connection to stove with
silicone.
FIRE HAS GONE OUT
1. No pellets in hopper.
2. Draft setting is too low.
3. Something is restricting fuel flow.
4. Feed motor or draft motor has failed.
The moisture content must not exceed 8%. Higher
moisture will rob BTU's and may not burn properly.
22 P61A Pellet Stove
Download from Www.Somanuals.com. All Manuals Search And Download.
P61A Feeder
P61A-2 Feeder and Specifications
Specifications
23.5"
9"
5.250"
Weight
249 lbs.
Blower
135 cfm
Feed Rate
Hopper Capacity
Fuel
.75 to 7.5 lbs. per hr.
72 lbs.
Wood Pellets
3 inch
Flue Size
Outside Air Size
Fuse Rating
2 3/8 I.D. inch
5 amp
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Door Options
Optional Trim
Decorative Tile
To install, lay the frame face down on a soft
surface. Fasten door frame by inserting the 4
threaded posts on the frame through the door. The
posts should line up with the 4 holes located at the
corners of the door. Once the posts are through the
door, fasten frame with 4 nuts and tighten until the
frame is snug.
Decorative tile is available in several configu-
rations. The tile installs behind the trim on the ash
door.
To install ash lip trim, simply slide the trim over
the ash lip and into the groove on the trim.
Cleaning Plated Trim
Gold or nickel plated hardware should never
be buffed or polished. Abrasive cleansers and metal
polishes will remove the plating and therefore should
never be used. If the plating needs to be cleaned,
wait until the stove is completely cool, then use a
sponge, soap and water to gently remove dirt and
stains. Before relighting the stove, remove all soap
residue and wipe dry.
24 P61A Pellet Stove
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONS
Side Heat Shields
Side heat shields are available to reduce
the clearance to combustible materials.
Hopper Extension
The hopper extension allows you to
put more pellet fuel in the hopper and extends
burn time on one load of pellets. The hopper
extension adds 60 pounds to the existing 72
pound hopper capacity, allowing you to load
132 pounds of pellets at one time.
P61A Pellet Stove 25
Download from Www.Somanuals.com. All Manuals Search And Download.
P61A-2 Wiring Diagram
26 P61A Pellet Stove
Download from Www.Somanuals.com. All Manuals Search And Download.
P61A-2 Parts List
Description
Part Number
0-88-00248
1-10-05800
1-10-05802
2-00-06468-1
2-00-06468-2
2-00-773850
3-00-08534
3-20-08727
3-20-00744
3-20-00906
3-20-05374
3-20-9301
Hopper Gasket(6 ft.)
Ash Pan Assembly
Burn Pot Weldment
Right Rear Shield
Left Rear Shield
Arrow Scraper
Flame Guide
Wiring Harness Assembly
Thermister Probe
Room Sensor
Circuit Board
Differential Switch
5" Double Fan Blade
Combustion Blower
Distribution Blower
Hopper Lid Latch
3-20-502221
3-21-08639
3-21-22647
3-31-199110
3/16" Rubber Washer (for Hopper Lid) 3-31-90131101
Power Cord 3-20-29685
Auto Ignite Label (Control Panel Door)3-90-08627
Fire Brick (3)
3-40-900450125
White/Black Control Knob(3)
Control Knob Shaft(3)
Front Glass
Burn Pot Gasket(2)
Tailpipe Gasket
Wiring Diagram
Control Panel Sticker
Owner's Manual
3-31-00605
3-31-00015
3-40-950133125
3-44-00409
3-44-06179
3-89-06504
3-90-06655
3-90-05822
3-90-08416
1-10-06620
2-00-06623
Hopper Lid Label
Igniter Assembly
Cleanout Cover(1)
1/4-20 x 1/2" Wing Screw w/Collar(2) 3-31-782108
Options:
Hopper Extension Assembly
Outside Air Assembly
Inlet Cover
1-00-08636
1-10-08542
1-10-08543
3' Flex Pipe
2-00-08543
Log Set
3-40-5647
Trim Kit
1-00-06802
Tile Pack(1 piece)
3-43-12601(10 choices)
P61A Pellet Stove 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Harman Gold Warranty
HARMAN GOLD WARRANTY
6 YEAR TRANSFERABLE LIMITED
WARRANTY (Residential)
1 YEAR LIMITED WARRANTY (Commercial)
Harman Stove Company warrants its products to be free from defects in material or workmanship, in normal use
and service, for a period of 6 years from the date of sales invoice and for mechanical and electrical failures, in normal
use and service, for a period of 3 years from the date of sales invoice.
If defective in material or workmanship, during the warranty period, Harman Stove Company will, at its option,
repair or replace the product as described below.
The warranty above constitutes the entire warranty with respect to Harman Stove Company products. HARMAN
STOVE COMPANY MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING ìANYî WAR-
RANTY OF MERCHANTABILITY, OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. No employee,
agent, dealer, or other person is authorized to give any warranty on behalf of Harman Stove Company. This warranty
does not apply if the product has been altered in any way after leaving the factory. Harman Stove Company and its
agents assume no liability for ìresultant damages of any kindî arising from the use of its products. In addition, the
manufacturer and its warranty administrator shall be held free and harmless from liability from damage to property
related to the operation, proper or improper, of the equipment.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
THESE WARRANTIES APPLY only if the device is installed and operated as recommended in the userís
manual.
THESE WARRANTIES WILL NOT APPLY if abuse, accident, improper installation, negligence, or use beyond
rated capacity causes damage.
HOW TO MAKEACLAIM -Any claim under this warranty should be made to the dealer from whom this appliance
was purchased. Then contact is made with manufacturer, giving the model and serial numbers, the date of purchase,
your dealerís name and address, plus a simple explanation of the nature of the defect. Extra costs such as mileage
and overtime are not covered. Nuisance calls are not covered by these warranties.
THIS WARRANTY IS LIMITED TO DEFECTIVE PARTS - REPAIR AND/OR REPLACEMENT AT
HARMAN STOVE COMPANYíS OPTION AND EXCLUDES ANY INCIDENTAL AND CONSEQUENTIAL
DAMAGES CONNECTED THEREWITH.
WARRANTY EXCLUSIONS: Failure due, but not limited to, fire, lightning, acts of God, power failures and/or
surges, rust, corrosion and venting problems are not covered. Damage and/or repairs including but not limited to;
remote controls, filters, fuses, knobs, glass, ceramic brick panels, ceramic fiber afterburners, door packing, tile, ce-
ramic log sets, paint, batteries or battery back-up and related duct work are not covered. Also excluded from this
warranty are consumable or normal wear items including but not limited to; flame guides, grates, coal bars, afterburner
hoods, fire brick, gaskets. Additional exclusions for corn stoves are burnpot housing weldment, burnpot grate weldment
(pellet or corn), burnpot front plate (pellet or corn), burnpot front plate lock, corn auger extension, ceramic insert, and
ceramic insert plate. Additional or unusual utility bills incurred due to any malfunction or defect in equipment and the
labor cost of gaining access to or removal of a unit that requires special tools or equipment are not covered. Mainte-
nance needed to keep the stove in ìgood operating conditionî is not covered. This includes, but is not limited to,
cleaning, adjustment of customer controls and customer education. Labor, materials, expenses and/or equipment
needed to comply with law and/or regulations set forth by any governmental agencies are not covered.
This Warranty provides specific legal rights and the consumer may have other rights that vary from state to state.
In the event of change in ownership, the remaining portion of this warranty may be transferred to the new owner by
sending the new owner information and a transfer fee of $25.00 US to the Harman Stove Company.
PLEASE READ THE LITERATURE BY THE MANUFACTURER FOR THE VARIOUS ACCESSORY
DEVICES. THE MANUFACTURER WARRANTS THESE ACCESSORY DEVICES, NOT HARMAN STOVE
COMPANY OR THEIR WARRANTY ADMINISTRATOR. FURTHERMORE, THESE ACCESSORY DEVICES
MUST BE INSTALLED AND USED ACCORDING TO THE RECOMMENDATIONS OF THE MANUFACTURER.
REMEDIES - The remedies set forth herein are exclusive and the liability of seller with respect to any contract or
sale or anything done in connection therewith, whether in Contract, in tort, under any warranty, or otherwise, shall not,
except as herein expressly provided, exceed the price of the equipment or part of which such liability is based.
CLARIFY - The above represents the complete warranty, which is given in connection with stoves, manufactured
by Harman Stove Company. No other commitments, verbal or otherwise, shall apply except by a written addendum to
this warranty.
28 P61A Pellet Stove
Download from Www.Somanuals.com. All Manuals Search And Download.
|