Owner's Manual
Installation and Operation
Model:
Oakleaf
Non-Catalytic, Top Load,
Wood Burning Room Heater
Item #1-90-797000
NOTICE
dO NOT dIsCaRd THIs MaNuaL
• Read, understand and • Leave this manual with
follow these instructions party responsible for use
for safe installation and and operation.
operation.
• Important operating and
maintenance instructions
included.
WaRNINg
WaRNINg
pLEasE REad THIs ENTIRE MaNuaL
BEfORE INsTaLLaTION aNd usE Of
THIs WOOd-BuRNINg ROOM HEaTER.
fa I L u R E TO f O L L O W T H E s E
INsTRuCTIONs COuLd REsuLT IN
pROpERTy daMagE, BOdILy INjuRy
OR EvEN dEaTH.
HOT suRfaCEs!
gLass aNd OTHER suRfaCEs aRE HOT
duRINg OpERaTION aNd COOL dOWN.
HOT, WILL CausE BuRNs.
•
•
•
•
dO NOT TOuCH gLass uNTIL IT Is COOLEd
NEvER aLLOW CHILdREN TO TOuCH gLass
kEEp CHILdREN aWay
CaREfuLLy supERvIsE CHILdREN IN saME
ROOM as fIREpLaCE.
aLERT CHILdRENaNd aduLTs TO HazaRds Of
HIgH TEMpERaTuREs.
HIgH TEMpERaTuREs May IgNITE CLOTHINg
OR OTHER fLaMMaBLE MaTERIaLs.
kEEp CLOTHINg, fuRNITuRE, dRapERIEs aNd
OTHER fLaMMaBLE MaTERIaLs aWay.
• dO NOT sTORE OR usE gasOLINE OR OTHER
fLaMMaBLE vapORs aNd LIquIds IN THE
vICINITy Of THIs OR aNy OTHER appLIaNCE.
• dO NOT OvERfIRE - If aNy ExTERNaL paRT
sTaRTs TO gLOW, yOu aRE OvERfIRINg. CLOsE
aIR CONTROLs. OvERfIRINg WILL vOId yOuR
WaRRaNTy.
•
• COMpLy WITH aLL MINIMuM CLEaRaNCEs TO
COMBusTIBLEs as spECIfIEd. faILuRE TO
COMpLy May CausE a HOusE fIRE.
•
CauTION
CHECk BuILdINg COdEs pRIOR TO INsTaLLaTION.
CauTION
TEsTEd aNd appROvEd fOR usE WITH dRy,
sEasONEd CORdWOOd ONLy. dO NOT BuRN WET
OR gREEN WOOd. BuRNINg aNy OTHER TypE Of
fuEL WILL vOId yOuR WaRRaNTy.
•
•
INsTaLLaTION MusT COMpLy WITH LOCaL, REgIONaL, sTaTE
aNd NaTIONaL COdEs aNd REguLaTIONs.
CONsuLT LOCaLBuILdINg, fIRE OffICIaLs ORauTHORITIEs
HavINg juRIsdICTIONaBOuT REsTRICTIONs, INsTaLLaTION
INspECTION, aNd pERMITs.
3-90-798
Rev: 5
May, 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
TaBLE Of CONTENTs
section 1: Listing and Code approvals
section 9: service & Maintenance
A. Soot Formation (Removal)
A. Appliance Certifications
B. Mobile Home Approval
C. Glass Specifications
4
28
29
4
4
4
4
B. General Maintenance Procedures
D. Electrical Rating
section 10: Reference Materials
A. Wiring Diagram (Blower Option)
B. Service Parts Listing
E. BTU & Efficiency Specifications
31
32
35
36
section 2: special Warnings and Notes
C. EPA Hang Tag
D. Warranty Policy
A. Carbon Monoxide Warnings &
Considerations
5
section 3: getting started
A. Design, Installation & Location6
B. Fire Safety
6
7
7
8
C. Component Locator
D. Flue Direction Conversion
E. Pre-Use Checklist
section 4: dimensions & Clearances
A. Appliance Dimensions
B. Clearances to Combustibles
C. Floor Protection
section 5: Chimneys and venting
A. Draft
9
10
12
This room heater must be connected to
1) a chimney complying with the requirements for
Type HT chimneys in the standard for Chimneys,
factory-Built, Residential Type and Building
Heating appliance, uL 103
13
13
13
14
B. Chimney Connectors
C. Wall Pass-Throughs
D. The Chimney
or
2) a Code approved Masonry Chimney with a flue
Liner.
section 6: Mobile Home - (us only)
A. Mobile Home Installation
21
section 7: appliance set-up
A. Outside Air Attachment
B. Leveling The Appliance
C. Optional Cooking Grill
22
22
22
23
23
23
D. Optional Blower Kit
E. Optional Rear Vent Rear Shield
F. Optional Bottom Heat Shield
section 8: Operating Instructions
A. Fuel Specifications
24
24
25
26
26
26
B. General Operating Information
C. Combustion Process
D. User Controls
E. Before Your First Fire
F. Building & Maintaining a Fire
3
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
Listing and Code approvals
1
E. BTu & Efficiency specifications
a. appliance Certification
Model:
Oakleaf Woodburning Stove
OMNI-Test Laboratories, Inc.
135-S-26-6.2
Solid Fuel Room Heater / Wood
Burning Type.
Particulate Emissions
Rating:
2.2g/hr Avg
Laboratory:
Report No.
Type:
15,000 - 39,000 / hr
*BTU Input:
Heating Capacity:
Firebox Size:
Fuel:
1,400-1,600 sq. ft.††
1.7 cu. ft.
Dry Cordwood
430 lbs.
Standard(s):
UL1482-10, &
ULC S627-00
Shipping Weight:
This appliance is also approved for installation in
a shop.
*BTU input based on EPA test fuel. Actual cordwood
values will vary.
B. Mobile Home approved
††Heating capacity based on zones 1 and 2, covering
the Northern United States.
This appliance is approved for Installation in mobile/
manufactured homes in the us only. The structural
integrity of the mobile home floor, ceiling and walls
must be maintained. The appliance must be properly
grounded to the frame of the mobile home, and must
never be installed in a room designated for sleeping.
The unit must have provisions for an outside air source
when installed in a mobile home.
C. glass specifications
This appliance is equipped with 5mm ceramic glass.
Replace glass only with 5mm ceramic glass. Please
contact your dealer for replacement glass if needed.
d. Electrical Rating
Optional Blower: 115 VAC, 60 Hz. <1 Amps
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
special Warnings and Notes
2
Carbon monoxide, referred to as CO, is a colorless,
CO detectors are very sensitive and may sound an alarm
for fumes other than CO or CO from sources other than
the stove such as car or lawn mower exhaust.
If the alarm sounds
odorless gas that is produced during combustion of wood
and other fuels. CO fumes are toxic and can be fatal.
The Oakleaf is a natural draft system which relies on
a properly designed chimney to remove CO and other
combustion by-products from the stove.
1. Increase ventilation by opening windows or doors.
2. Make sure the stove doors and lid are closed and latched.
3. Check stove for smoking or puffing condition. Open
by-pass and increase air-flow to firebox, if needed.
4. Check chimney for possible blockage or down-draft.
5. Check for false alarm.
Even though this stove is designed to be as safe as
possible, it is important that you install a CO detector.
This is true for oil, gas, or coal burning products as well.
CO is not specifically heavier or lighter than air.
Therefore, it is best to install the detector at table top level
rather than on the ceiling like a smoke detector.
Never use gasoline, lantern fuel, kerosene,
charcoal lighter fluid, or similar liquids to start
or “freshen up” a fire in this heater. keep all
such liquids well away from the heater while it
is in use.
NEvER CONNECT THIs uNIT TO a CHIMNEy
fLuE sERvINg aNOTHER appLIaNCE.
Installation and repair of this stove should
be done by a qualified service person. We
recommend that the stove be inspected
before use and at least annually by a qualified
service person. periodic cleaning is required
throughout the heating season and at the end
of each winter for the stove to work efficiently.
spECIaL NOTE:
duE TO asH BuILdup, IT Is sTRONgLy
RECOMMENdEd TO HavE yOuR sTOvE
pROfEssIONaLLyCLEaNEdaNdsERvICEd
aNNuaLLy. THIs INCLudEs aLL paRTs Of
THE sTOvE, aNd THE vENTINg sysTEM.
dO NOT CONNECT TOaNyaIR dIsTRIBuTION
duCT OR sysTEM.
If INsTaLLINg ON a COMBusTIBLE fLOOR,
THE BOTTOM HEaT sHIELd MusT BE
INsTaLLEd aLONg WITH pROpER fLOOR
pROTECTION MaTERIaL.
5
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
getting started
3
a. design, Installation & Location
Considerations
B. fire safety
Maintain the designated clearances to combustibles.
Insulation must not touch the chimney. You must
maintain the designated air space around the chimney.
This space around a chimney is necessary to allow
natural heat removal from the area. Insulation in this
space will cause a heat buildup, which may ignite wood
framing. NOTE: Clearances may only be reduced
by means approved by the regulatory authority
having jurisdiction.
1. appliance Location
Consideration must be given to safety, convenience,
traffic flow, and the fact that the appliance will need
a chimney and chimney connector. It is a good
idea to plan your installation on paper, using exact
measurements for clearances and floor protection,
before actually beginning the installation. When
installing on a combustible floor, the optional bottom
heat shield must be installed along with using proper
floor protection material. See page 12 for details.
To provide reasonable fire safety, the following should
be given serious consideration:
1. Install at least one smoke detector on each floor
of your home. Detectors should be located away
from the heating appliance and close to sleeping
areas. Follow the smoke detector manufacturer's
placement and installation instructions, and be
sure to maintain regularly.
Maintain specified vent clearance to combustible
requirements listed by the vent manufacturers
instructions and all clearance to combustibles listed in
this manual.
2. A conveniently located Class A fire extinguisher
to contend with small fires resulting from burning
embers.
3. A practiced evacuation plan, consisting of at least
two escape routes.
Check with your local building code agency before
you begin your installation. Be sure local codes do not
supersede UL specifications and always obtain the
required permit so that insurance protection benefits
cannot be unexpectedly cancelled. If any assistance is
required during installation, please contact your dealer.
4. A plan to deal with a chimney fire as follows:
In the event of a chimney fire:
a. Evacuate the house immediately.
b. Notify Fire Department.
c. Never apply water to a suspected chimney fire.
Serious damage could occur.
We recommend that a qualified building inspector and
your insurance company representative review your
plans before and after the installation.
Be sure to provide a source of fresh air to the room
or directly to the appliance. Make-up air is needed to
replace what the chimney draws away through the
appliance.
WaRNINg
fIRE HazaRd
•
dO NOT OpERaTE appLIaNCE
BEfORE REadINg aNd
CauTION
uNdERsTaNdINg THE OpERaTINg
INsTRuCTIONs.
faILuRE TO OpERaTE pROpERLy
May CausE a HOusE fIRE.
•
•
dO NOT CONNECT THIs uNIT TO a CHIMNEy fLuE
sERvICINg aNOTHER appLIaNCE.
•
dO NOT CONNECT TO aNy fORCEd aIR
dIsTRIBuTION duCT OR sysTEM.
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
C. Component Locations
Top Load Door
Top Load Opening
Bypass Damper
Control Handle
Front Load Door
Air Control
Front Load
Door Latch
Ash Door
Level
adjuster
Ash Door
Latch
d. flue direction Conversion
The Oakleaf features an adjustable flue collar for rear or top exit. Follow these instructions for changing the
direction. First, remove the upper rear heat shield by removing 8 tek screws that secure it. Reaching upward
through the firebox and the open bypass damper, loosen the retainer bolts on each of the flue collar and the cast
iron plate. With the bolts loosened, turn the retainer to allow the piece to come free of the stove body. Reposition
the flue collar and the cast iron plate and secure them with the retainers by tightening the bolts. You will now need
to install a different upper rear heat shield. (See page 23).
7
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
E. pre- use Check List
1.
Place the appliance in a location near the
final installation and follow the procedures
below:
WaRNINg
INspECT appLIaNCE aNd
COMpONENTs fOR daMagE. daMagEd
paRTs May IMpaIR safE OpERaTION.
2.
Open the appliance and remove all articles
packed inside. Inspect all items for shipping
damage. Notify dealer of any missing or
damaged goods.
All safety warnings have been read and
followed precisely.
This Owner's Manual has been read in it's
entirety.
Floor protection requirements have been
read and followed.
The flue connector has been installed in
accordance with the instructions herein.
The proper clearances from the appliance
and chimney connector to combustibles
have been met.
The masonry chimney has been cleaned
and inspected by a professional, or the
factory built metal chimney is installed
according to the manufacturers instructions.
The chimney meets the minimum height
requirements.
All labels and hang tags have been removed
from the glass.
All plated surfaces have been wiped clean,
if applicable.
The optional air distribution blower
has been installed properly.
A properly grounded electrical receptacle is
available within reach of the blower's power
cord (if installed).
•
•
•
dO NOT INsTaLL daMagEd
COMpONENTs.
dO NOT INsTaLL INCOMpLETE
COMpONENTs.
dO NOT INsTaLL suBsTITuTE
COMpONENTs.
3.
4.
5.
6.
7.
REpORT daMagEd paRTs TO dEaLER.
WaRNINg
fIRE RIsk.
HEaRTH & HOME TECHNOLOgIEs
dIsCLaIMs aNy REspONsIBILITy
fOR, aNd THE WaRRaNTy WILL
BE vOIdEd By, THE fOLLOWINg
aCTIONs:
8.
•
INsTaLLaTION aNd usE Of aNy daMagEd
appLIaNCE.
9.
•
•
MOdIfICaTION Of THE appLIaNCE.
INsTaLLaTION OTHER THaN as INsTRuCTEd By
HEaRTH & HOME TECHNOLOgIEs.
INsTaLLaTION Of paRTs OR COMpONENTs NOT
suppLIEd OR appROvEd By HEaRTH & HOME
TECHNOLOgIEs.
OpERaTINg appLIaNCE WITHOuT THE LEgs
aTTaCHEd.
OpERaTINg appLIaNCE WITHOuT fuLLy
assEMBLINg aLL COMpONENTs.
dO NOT OvERfIRE.
10.
11.
12.
13.
•
•
•
•
OR aNy suCH aCTION THaT May CausE a fIRE
HazaRd.
There are two brick clips located in the Owner’s manual bag. With the bricks in place, install the clips in the front corners
as shown. The long portion of the clip will fit between the brick and the wall of the stove, with the short hook over-hanging
to the inside of the firebox.
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
dimensions & Clearances
4
a. appliance dimensions
25"(635mm)
air Intake
29.2"
(742mm)
10.2"
(259mm)
27.2"
(691mm)
When configured for rear flue; floor to center of flue
measures 23.5" (597mm)
NOTICE: When using rear flue configuration, a new
upper rear heat shield, #1-00-797066 must be installed
in place of the existing shield.
26.2"
(665.5mm)
Centered
Weight
430 lbs
Flue Size
6 inch
Log Length Recommended
Average Emissions
Outside Air size
18"
27.6"
(701mm)
2.2 Grams Per Hr.
4.5 inch I.D.
25.6"
(650mm)
18.9"
(480mm)
The Harman Oakleaf meets the
U.S. Environmental Protection
Agency’s emission limits for wood
heaters sold after July 1, 1990.
9
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
B. Clearances To Combustibles
CLEaRaNCE TO COMBusTIBLEs: vertical venting Configuration
Location
pipe clearance may be reduced using double wall
or insulated connector pipe, provided that you
adhere to the specified clearances from the stove
itself. follow pipe manufacturer's guidelines.
a
B
C
d*
unit to side Wall
unit to Back Wall
vent pipe to side Wall
vent pipe to Back Wall
17" / 432 mm
14" / 356 mm
26.75" / 679 mm
*17.5" / 444 mm
d*
B
C
* Nfpa 211 specifies 18" clearance to
single wall connector pipe. This lower
clearance is based on actual safety
test conditions.
a
for clearance reduction methods, refer to Nfpa 211 or Local Codes
CLEaRaNCE TO COMBusTIBLEs: vertical vent, Horizontal Exit
Location
pipe clearance may be reduced using double wall
a
B
C
d*
E*
f
unit to side Wall
unit to Back Wall
vent pipe to side Wall
vent pipe to Back Wall
vent pipe to Ceiling
Minimum vertical
16" / 407 mm
13" / 330 mm
25.25" / 641 mm
*17" / 432 mm
*16" / 407 mm
0" / 0 mm
or insulated connector pipe, provided that you
adhere to the specified clearances from the stove
itself. follow pipe manufacturer's guidelines.
* Nfpa 211 specifies 18" clearance to
single wall connector pipe. This lower
clearance is based on actual safety
test conditions.
E
E
f
C
d
C
a
B
a
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
pipe clearance may be reduced using double wall or insulat-
ed connector pipe, provided that you adhere to the specified
clearances from the stove itself. follow pipe manufacturer's
guidelines.
CLEaRaNCE TO COMBusTIBLEs: Corner Installation,
vertical vent
Location
a
B
shield Corner to Wall
vent pipe to Wall
14" / 356 mm
21.75" / 552 mm
B
a
B
a
B
a
CLEaRaNCE TO COMBusTIBLEs: Corner Installation
vertical vent, Horizontal Exit
Location
a
B
shield Corner to Wall
vent pipe to Wall
14" / 356 mm
21.75" / 552 mm
*for clearance reduction methods, refer to Nfpa 211 or Local Codes
CLEaRaNCE TO COMBusTIBLEs: Horizontal venting Configuration
Location
a
B
C
unit to side Wall
unit to Back Wall
vent pipe to side Wall
17" / 432 mm
13" / 330 mm
26.5" / 673 mm
Corner Installation
d
E
shield Corner to Wall
Nfpa 211 specifies clearance of
14" / 356 mm
18" / 457 mm
(although vent clearance may be reduced using double-wall pipe, d must be
followed)
NOTICE: When using rear flue configuration, a new upper rear heat shield, #1-00-797066 must be installed in
place of the existing shield.
C
B
a
E
d
11
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
C. floor protection Requirements
daNgER: The appliance legs may not be removed
for installation.
Minimum Size floor protection (USA) is 48" Deep By
32.5" Wide.
L
floor protection
Requirements
Inches
Millimeters
8
203
457
203
Wall
Sides- USA /CANADA *
Front- USA /CANADA *
Rear- USA
j
k
L
L
18
8
j
j
Rear- CANADA
Wall
k
* Floor protection for the front and sides as measured
from the appliance door opening.
floor protection Requirements
If the Oakleaf is being installed on a combustible
floor, the bottom heat shield (part # 1-00-797058) must
be installed along with proper floor protection material.
(See page 25). Floor protection must be a minimum
3/8" (9.5mm) thickness of material having an insulating
value equal to or better than 0.84k/in. (The lower the k
value, the better the protection.)
Minimum 60" corner floor protection (USA & CANADA).
Another method for calculating floor protection is in
R value. This requirement would be for an R value of
0.45 or higher. (The higher the R value, the better the
protection). Example- 1 inch of Durock® = 0.52R
In all installations, the area under and around the
stove must be protected from falling ash and live coals.
The area under a horizontal run of chimney connector
must also be protected, extending two (2) inches
beyond the measurement of the horizontal connector.
Further guidelines for floor protection are as follows:
In the U.S. the floor protector must be completely
under the stove, and extending 16" in front of the door
opening, 8" to each side and 8" to the back.
In Canada, the floor protection must extend 18"
(457mm) in front of the door opening, 8" (203mm) to
each side and extend to the wall behind the stove.
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
The Chimney Connector shall Not pass Through an
attic or Roof space, Closet or similar Concealed space,
a floor or Ceiling.
Chimneys and venting
5
Assemble the connector beginning at the flue collar,
with the crimped ends pointing towards the stove (to
keep debris or residue inside the system). Each joint,
including the one to the stove’s flue collar and the one
to the chimney itself should be secured with at least
three sheet metal screws. Screws may be a maximum
of 3 inches apart. A 1-1/4" (30 mm) overlap is required
at each joint, including the flue collar attachment. No
more than two 90 degree elbows should be used, and
the total length of connector should not exceed 10 feet
(3 m). All horizontal runs of connector must have a
minimum upward slope of 1/4"(6 mm) per foot (20 mm
per meter).
a. draft
Draft is widely misunderstood. It is important that
you, the stove operator, realize that draft is a variable
effect, not a given quantity. Stoves and chimneys
do not have draft, yet draft is the key to your stove’s
performance.
Draft is a force, produced by an operating stove
and the chimney to which it is attached. It is created by
hot gases rising up the chimney, creating a pressure
difference between the inside of your home and the
outside air. It continually moves fresh combustion air
into the stove, and hot exhaust gases out of the stove;
without this constant flow, the fire will go out.
Other factors, such as barometric pressure,
winds, the airtightness of the home, the total inside
chimney volume, chimney height and the presence
of venting devices such as exhaust fans also play a
role in maintaining an adequate draft. Low barometric
pressures, super insulated homes and exhaust fans can
reduce draft; winds can play havoc with draft; and too
large or too small a chimney volume can cause reduced
draft due to the excessive cooling or not enough room
to vent exhaust gases. Introducing outside air directly
to the stove may help remedy a low draft problem.
Some signs of inadequate draft are smoking, odor,
difficulty in maintaining the fire, and low heat output.
Overdraft can be caused by a very tall chimney even if
it is the recommended size, and can cause overfiring
of your stove. Signs of an overdraft include rapid fuel
consumption, inability to slow the fire, and parts of the
stove or chimney connector glowing red. It is important
that you follow the chimney guidelines in this manual,
including size, type, and height to avoid draft problems.
When installed and operated according to this
manual, the Oakleaf will produce enough hot gases
to keep the chimney warm so that adequate draft is
maintained throughout the burn cycle.
The chimney connector diameter should correspond
to the size of the flue collar opening. Do not use
makeshift compromises. No part of the chimney
connector may pass through an attic or roof cemented
in place with refractory cement.
C. Wall pass-thrus
Depending on your local building codes, and the
pertinent provincial or national codes, there are several
choices for passing the chimney connector safely
through a wall. Before beginning your installation,
contact local officials, and also the chimney connector
and chimney manufacturer for specific requirements.
Canada. Three methods are approved by the
Canadian Standards Association. The diagram on the
next page shows one method requiring an 18"(450 mm)
air space between the connector and the wall. It allows
use of one or two covers as described in the diagram.
The two other methods are described in detail in the
current issue of CAN/CSA B365, the national standard.
United States In the U.S., the national code is NFPA
211. While many localities adopt this standard, be sure
to check with local authorities before beginning your
installation.
The NFPA(National Fire ProtectionAgency) permits
four methods for passing through a combustible wall. A
commonly used method to pass through a wall directly
to a masonry chimney is to clear a minimum 12"(300
mm) around the entire chimney connector, and fill it
with brick masonry which is at least 3.5"(90 mm) thick.
A fireclay liner, minimum 3/8" (9 mm) wall thickness
must run through the brick wall to the chimney liner (but
not beyond the inner surface of the liner). It must be
cemented in place with refractory cement. This method
is illustrated on the next page. For details on the other
three options, refer to the most recent edition of the
NFPA 211 code.
B. Chimney Connectors
In general, following these guidelines will ensure
compliance with all national and provincial codes;
prior to beginning your installation, check with your
local building code official to check on additional
local regulations which may influence the design and
placement of your venting system.
TheHarmanOakleaf maybeinstalledwithaminimum
(.6 mm) 24 gauge chimney connector pipe. The size of
the connector should correspond to the size of the flue
collar opening. Do not use makeshift compromises. No
part of the chimney connector may pass through an
attic or roof space, closet or other concealed space,
or through a floor or ceiling. Whenever possible, avoid
passing the connector through a combustible wall; if you
must, use an approved wall pass-through, described
later in this section.
13
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
Non-combustible cover,
one side only. If two
covers are used, each
must be mounted on
non-combustible spacers
at least 7/8" (21mm) away
from the wall.
Closest
Combustible
Material
Minimum 2" (50mm)
Clearance to Brick
Hole with a minimum clear-
ance of 18" (450 mm) be-
tween connector and wall.
Minimum 12"
Liner
(300mm) to Brick
Fire Clay
Thimble
Chimney
Connector
1" (25mm)
Clearance
Masonry Chimney Built to
NFPA 211 Specifications.
Minimum 12" (300mm)
to Combustibles
AN APPROVED CANADIAN
WALL PASS-THROUGH
AN APPROVED U.S.
WALL PASS-THROUGH
d. The Chimney
This unit must be installed into a chimney approved
for use with solid-fuel appliances. In the U.S., it must
be connected to (1) a prefabricated chimney complying
with the requirements for Type HT chimneys in the
Standard for Chimneys, Factory-Built, Residential Type
and Building HeatingAppliances, UL103, or (2) a code-
approved masonry chimney with a flue liner.
In Canada, this unit is listed for use with prefabricated
chimneys tested and listed to the high temperature (650
degrees C) chimney standard, ULC S-629, or with a
code approved masonry chimney.
Do not connect this unit to a chimney
flue servicing another appliance.
NOTE: The restriction of not venting more than one appliance
to the same flue applies to the U.S. specifically. While it is not
recommended that you use the same chimney for more than
one appliance, in Canada certain exceptions may be made.
Be sure to contact your building code inspection official to
see if this option is allowed in your area, and to find out the
specific requirements for such an installation.
For mobile homes, (US only) it must only be installed
with a factory built stainless steel chimney. The
chimney system should include all required installation
components, such as vapor barriers and roof flashing,
as tested for use in mobile homes.
The minimum recommended height for any chimney
is 16 ft. (4.8 m) above flue collar height. For non-mobile
home installations, a round flue (either masonry or
approved prefabricated), of either 6" (150 mm), 7"
(180 mm) or 8" (200 mm) may be used. For square or
rectangular masonry chimneys, nominal sizes of 8" x
8" or 7" x 12" (200mm x 200 mm, 180 mm x 300 mm)
may be used.
More Than 10 ft. (3m)
Height Necessary
Above Any Roof
Surface Within 10ft.
10 ft. (3m)
(3m)
2 ft. (0.6m) min.
3ft. (0.9m)
minimum
above
exit
point
Ridge
Codes require that solid-fuel chimneys extend 3 ft.
(0.9 m) above the highest point at which they exit from
the roof. Then, the chimney must extend 2 ft. (0.6 m)
above the highest point within a 10 ft (3 m) radius. Thus,
the 3 foot, 2 foot, 10 foot rule:
Chimney
The 3-foot, 2-foot, 10 foot rule
3ft. - Above roof exit point
2ft. - Higher than anything within-
10ft. of the chimney.
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
1. Existing Masonry Chimneys
If you plan on using a pre-existing masonry chimney,
have it thoroughly inspected and cleaned. Any faults
which make the chimney unsafe and unusable must
be repaired prior to use. These can include improper
height, structural defects, blockages, inadequate
clearance to combustibles, unsealed openings into
other rooms of the house, signs of creosote or smoke
leakage, a loose or absent clean-out door, or absence
of a liner.
2. venting to a Masonry Chimney
When connecting to a masonry chimney, several
provisions are standard. First, whether the chimney
connector is vented to the chimney through a thimble
or a breech pipe, neither must pass beyond the inner
surface of the chimney liner, and both must be firmly
cemented in place with refractory cement. (Athimble is
a masonry pipe which is inserted through the chimney
wall, and is frequently the preferred method; a breech
pipe is a piece of steel pipe used the same way.) In
Canada, a breech pipe has ridges or protrusions to
lock it firmly into the refractory cement. In either case,
the chimney connector vents to the chimney through
the thimble or breech pipe.
Using a thimble, the connector slides completely
inside the masonry to the inner edge of the flue liner,
and may be easily removed for chimney and connector
inspection. A breech pipe must extend at least 2" (50
mm) into the room, so the connector can be attached
with sheetmetal screws.
4. Installing to a prefabricated Chimney
When venting using a prefabricated chimney, be sure
to contact local building code authorities, and to follow
the manufacturer’s instructions exactly. Use only the
manufacturer’s parts; do not use makeshift installation
techniques. All prefabricated chimneys must be
tested to either the U.S. or Canadian high-temperature
standards, UL 103 or ULC S629.
3. venting to a Masonry fireplace Chimney
5. Other Considerations
Insomesituations, acodecompliantchimneyoriginally
used for a masonry fireplace may be used. In addition
to the requirements found in the previous paragraphs,
it is important to be aware that all clearances must be
met, including those from the chimney connector to
combustibles. Do not forget to include floor protection
in your plans. (See Clearances and Floor Protection
in this section.) Since many fireplaces have exposed
wooden mantels and trim, pay special attention to the
clearances necessary to these materials.
If your fireplace chimney is behind a combustible wall,
you must use an approved wall pass-through system
to gain access to the masonry chimney. The chimney
connector must enter the chimney at a place where it is
lined, and the fireplace must be made inoperable. For
example, you might remove the damper, replacing it
with a secure, airtight, noncombustible seal (removable
for inspection); this also satisfies the requirement that
no room air must be allowed to enter the chimney.
Do not burn any fuel other than dry cordwood. Never
use highly volatile substances in your stove, such as
gasoline, which could cause an explosion.
When solid fuels are burned completely, they produce
water and carbon dioxide. However, in long slow
burns, a substantial amount of carbon monoxide may
be produced. If allowed to build up, carbon monoxide
(which is odorless) can prove fatally poisonous. Proper
ventilation and draft will prevent this from happening.
If you smell smoke, thoroughly ventilate your dwelling,
and contact your dealer for service.
Other causes of poor ventilation or draft are icing,
exhaust fans, a blocked outside air inlet, and room
air starvation. If your stove is sluggish and you get
occasional odor, check these possibilities and increase
the air flow in your home.
15
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
standard Ceiling Installation with
factory Built Chimney
Cathedral Ceiling Installation with
factory Built Chimney
Chimney Cap
storm Collar
Chimney
sections
Chimney Cap
Roof flashing
Roof Radiation
shield
Roof
Radiation
factory-Built
Metal Chimney
shield
attic
Radiation
shield
sealed storm Collar
Roof flashing
Cathedral style
Chimney support
Minimum air space
with Chimney Listing
Chimney
support
finishing
Collar
Chimney
Connector
Chimney
Connector
The Chimney Connector shall Not pass Through an attic or Roof space, Closet or similar Concealed space, a
floor or Ceiling.
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
Chimney Breach fireplace Conversion with Non-Combustible Wall
Minimum Clearance
to unprotected
Ceiling 16"
Chimney Connector
sealed at Thimble
flue Liner with
Required air space
airtight
insulated
Clean-
out
Three sheet Metal
screws per joint of
Chimney Connector
Mantel and Trim
protection
damper
Closed
and sealed
with Non-
Combustible
Material.
floor protection*
Combustible floor
* floor protection in accordance
with solid fuel appliance Listing
The Chimney Connector shall Not pass Through an attic or Roof space, Closet or similar Concealed space, a
floor or Ceiling.
17
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
Oakleaf to flue fireplace Conversion (Minimum Nfpa 211 Liner Connection)
flue Liner with Required
air space
airtight
insulated
Clean-Out
stainless steel Chimney
Connector Must Extend
to flue Liner
Minimum 8" Masonry
Thickness in front of
smoke Chamber
use damper adapter
or seal with Non-
Combustible Material
damper plate
is Removed or
fastened in Open
position
Listed fireplace
Trim protection for
Reduced Clearance
floor protection*
Combustible floor
*floor protection in accordance with solid fuel appliance Listing
NOTICE: When using rear flue configuration, a new upper rear heat shield, #1-00-797066 must be installed in
place of the existing shield.
The Chimney Connector shall Not pass Through an attic or Roof space, Closet or similar Concealed space, a
floor or Ceiling.
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
full Relining fireplace Conversion: freestanding appliance
uL1777 stainless steel Liner system or
Other approved lining system
follow liner manufacturer's
instructions on insulation and
support
uL1777 Insulated stainless
steel flex Liner or Other
approved Lining system in
Offsets.
Listed fireplace Trim protection for
Reduced Clearance
damper plate Removed or
fastened in Open position
use damper adapter
or seal with Non-
Combustible Material
floor protection*
Combustible floor
*floor protection in accordance with solid fuel appliance Listing
NOTICE: When using rear flue configuration, a new upper rear heat shield, #1-00-797066 must be installed in
place of the existing shield.
The Chimney Connector shall Not pass Through an attic or Roof space, Closet or similar Concealed space, a
floor or Ceiling.
19
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
Chimney Breach fireplace Conversion with Combustible Wall
Minimum Clearance from
Chimney Connector to
unprotected Ceiling
16"**
flue Liner with Required air space
Listed or approved Thimble assembly
Combustible
Wall
1"Clearance for Complexity
Exterior Chimney or 2"
Clearance for Interior
Chimney and 2" Clearance
for Nfpa 211-Type
sheetrock
airtight
insulated
Clean-out
approved Thimbles
Mantel & Trim
protection
damper Closed
and sealed with
Non-Combustible
Material.
floor protection*
Combustible floor
* floor protection in accordance with solid fuel appliance Listing
** Check with your local building codes for clearance.
The Chimney Connector shall Not pass Through an attic or Roof space, Closet or similar Concealed space, a
floor or Ceiling.
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
Mobile Home
6
a. Mobile Home Installation
CauTION
Mobile home approval - u.s. only.
dO NOT INsTaLL IN a MOBILE HOME IN CaNada.
MaINTaIN sTRuCTuRaL INTEgRITy Of MOBILE HOME:
•
fLOOR, WaLL, CEILINg aNd/OR ROOf.
1. An outside air inlet must be provided for combustion
air, and must remain clear of leaves, debris,
ice, and/or snow. The outside air path must be
unrestricted while the appliance is in operation.
2. The combustion air intake system must be of
metal construction. It must permit zero-clearance
to combustible materials, and contain a rodent
screen.
dO NOT CuT THROugH:
•
•
fLOOR jOIsT, WaLL sTuds, OR CEILINg
TRussEs.
aNy suppORTINg MaTERIaL THaT WOuLd
affECT THE sTRuCTuRaL INTEgRITy.
3. The appliance must be secured to the mobile
home structure by bolting it to the floor. There are
brackets included, you'll need to secure with the
proper length lag bolts.
4. The appliance must be grounded to the metal
framing of the mobile home
CauTION
NEvER dRaW OuTsIdE COMBusTION aIR fROM:
•
•
WaLL, fLOOR OR CEILINg CavITy.
ENCLOsEd spaCE suCH as aN aTTIC OR
gaRagE
5. All clearances to combustibles and floor protection
requirements must be followed.
6. Follow the vent manufacturer's instructions when
installing in a mobile home.
7. Installation shall be in accordance with the
Manufactured Home and Safety Standard (HUD)
CFR 3280, Part 24
8. The appliance must never be installed in a room
designated for sleeping.
WaRNINg
INsTaLLaTION MusT COMpLy WITH
MaNufaCTuREd HOME aNd safETy sTaNdaRd
(Hud), CfR 3280, paRT 24.
This diagram shows the bracket that was used to
bolt the stove to the pallet. Use at least two of these
brackets for securing the appliance through the floor
in a mobile home installation. The bracket will slip
over the top of the leveling adjuster. The installer will
need to determine and obtain the properly sized lag
bolts.
WaRNINg
NEvER INsTaLL IN a ROOM INTENdEd fOR sLEEpINg.
21
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
appliance set-up
7
a. Outside air attachment
B. Leveling the appliance
Parts and Supplies Needed: 1 piece of metal flexible
pipe, 4" X needed length. 1 Rodent Screen, and
aluminum tape. Plus, a trim ring for finishing around
the pipe on the inside wall.
To adjust the leveling bolts, you must first loosen
the locking nut. Turn the leveling bolt to the desired
position, and tighten the locking nut against the cast
iron leg.
1. Determine an appropriate hole location, through
the wall. Be sure there are no studs or other
supporting members. Also ensure there are no
electrical wires or plumbing contained within the
wall.
2. Make the hole through the exterior wall using a
hole saw or reciprocating saw. You'll want the hole
to be just slightly larger than the metal flex pipe.
3. Attach the rodent screen to one end of the flex
pipe, and insert it through the wall until the back
of the screen cover is against the outside surface.
4. Hold the flex pipe in place to make an accurate
determination of the length needed. Cut the flex
pipe to length.
5. Slide the trim ring onto the flex for the inside wall
portion.
6. Slide the other end of the metal intake flex pipe
into the stub on the rear of the Oakleaf and secure
it with aluminum tape. This air intake will supply
outside air for the secondary combustion within the
FireDome.
C. Optional Cooking grill
The optional cooking grill #1-00-08121 installs easily
in the top load opening of the Oakleaf.
The grill handle (B) fits in the slots (C) on each side.
To remove the handle, lower and turn.
When installed, the grill hangs in the opening by the
hooks (A).
When grilling, you'll want to keep the fire size
small and the bypass damper in the open position.
Depending on the grilling being done, you may get
grease dripping on the glass causing it to become
dirty and obstructed. When you burn your next hot
fire, the glass will likely clean itself.
7. Secure the trim ring in place for finishing the inside
wall area.
8. Seal around the rodent screen on the exterior wall,
using silicone caulking.
a
CauTION
B
NEvER dRaW OuTsIdE COMBusTION aIR fROM:
•
•
WaLL, fLOOR OR CEILINg CavITy.
ENCLOsEd spaCE suCH as aN aTTIC OR gaRagE
a
C
C
a
Outside Air
Attachment
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
d. Optional Blower Installation
E. Optional Rear-vent Rear shield
The optional blower kit #1-00-797032 installs easily to
the rear of the Oakleaf.
Hold the blower assembly into place and secure it with
the two bolts provided. You'll need a 3/8" wrench or
socket to tighten the bolts.
Whenever a rear vent configuration is used, the upper
rear heat shield, #1-00-797066 must be purchased
and installed, to accomodate the flue collar. There
are eight screws that secure the existing shield. You'll
need to break away the tabbed portion of the lower
shield flue cut-out. Remove the screws from the top-
vent shield and install the rear vent shield in it's place.
Height adjustment for blower use is done the same
as with the top-vent shield in place. See D. Optional
Blower Installation (above) for detailed instructions.
If not installing the
optional blower, the
upper knockout will
need to be removed.
secure blower with one bolt on each end of the
mounting plate.
Notice: When installing the optional blower, the
upper rear shield must be moved upward to create
the air passage.
shown with lower shield
knockout removed.
Loosen the eight screws to remove the rear shield.
Raise the shield to the upper set of holes, re-install the
shield, and tighten the screws.
f. Optional Bottom Heat shield
Part #1-00-797058 must be purchased and installed
whenever the Oakleaf is installed on a protected
combustible floor. The shield installs on four bolts that
are protruding downward from the base of the stove
body. Slide the shield under the stove from the back,
as this is the only way it will fit. Lift into place guiding
the bolts through the holes in the shield and secure
with the nuts that are included with the shield.
WaRNINg
ROuTE pOWER CORdaWay fROM THEappLIaNCE.
dO NOT RuN THE CORd uNdER OR IN fRONT Of
THE appLIaNCE.
Plug the blower into a properly grounded electrical
outlet.
You can turn the blower on at any time using the rocker
switch on the rear of the blower housing. Setting the
switch to "AUTO" will keep the blower off until there
is a significant amount of heat from the stove. In this
setting, the blower will also shut off when the stove
cools. Keep the blower on low speed or off during low
fires. As you get out of the low burn range, the speed
can be set wherever desired, or kept off.
23
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
Operating Instructions
8
CauTION: approved for use with wood fuel only.
The use of any other fuel will void the product
warranty and may cause damage to the appliance
and/or your home.
CauTION:
aLWays WEaR fIRE RETaRdaNT gLOvEs
WHEN OpERaTINg THE sTOvE.
safETy NOTICE
If THIs appLIaNCE Is NOT pROpERLy INsTaLLEd,
OpERaTEd aNd MaINTaINEd, a HOusE fIRE
May REsuLT. fOR yOuR safETy, fOLLOW
WaRNINg
"NEvER usE gasOLINE, gasOLINE-TypE LaNTERN
fuEL, kEROsENE, CHaRCOaL LIgHTER fLuId, OR
sIMILaR LIquIds TO sTaRT OR "fREsHEN up " a
fIRE IN THIs HEaTER. kEEp aLL suCH LIquIds
WELL aWay fROM THE HEaTER WHILE IN usE".
INsTaLLaTION dIRECTIONs.
CONTaCT
LOCaL BuILdINg OR fIRE OffICIaLs aBOuT
REsTRICTIONs aNd INsTaLLaTION INspECTION
REquIREMENTs IN yOuR aREa.
dO NOT BuRN gaRBagE OR fLaMMaBLE LIquIds
suCH as gasOLINE, NapTHa, OR ENgINE OIL.
a. fuel specifications
Select only dry, seasoned wood. Wood for burning
should never be exposed to rain or extremely damp
conditions. Hardwoods are favored because they are
heavier and contain more heating capacity (BTU’s) per
load than do softwoods. Fuel wood should be split and
stored under cover for “seasoning” - at least a year is
recommended. Your stove is not an incinerator - do
not burn garbage, painted or treated wood, plastic, or
other debris.
Keep the area around the stove free from clutter.
Keep all combustibles, including fuel, beyond the code-
required clearance distance (48" or 1215 mm in the
U.S., 1525 mm or 60" in Canada). Never store fuel
in front of the stove where it could interfere with door
operation, safe loading, and ash removal.
B. general Operating Information
1. draft
Before you install and operate your Oakleaf
wood stove, please read the entire contents of this
manual. Pay particular attention to the explanation
of draft and its effect on stove performance in
the Installation section. By following the installation
and operating guidelines, you will ensure proper draft
and gain maximum efficiency and enjoyment from your
stove.
dO NOT aLTER THE pOsITION Of THE aNdIRONs.
BuILdINg a fIRE TOO CLOsE TO THE gLass May
CausE daMagE TO THE gLass, CREaTINgasERIOus
RIsk Of fIRE aNd pROpERTy daMagE.
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
2. doors
Your stove has a large glass-paneled door for loading
and fire viewing, a separate smaller door for removing
ashes and a top loading door.
C. The Combustion process
Combustion in the Harman Oakleaf is precisely
controlled and is best explained in two parts.
Front Door
During a wood fire, combustion air enters at the
bottom front of the stove where it travels upward through
channels at either side of the front door. From the
manifold located above the front door, it is directed into
the firebox as a sheet of air flowing between the glass
and the wood. This concept helps to keep the glass
clean, while providing the oxygen needed to sustain
burning. This is what is known as "Primary Combustion".
Additional air enters at the bottom rear of the stove
body. Some of this air enters through holes in the rear
bricks where it is used to revitalize the fire at the rear
of the firebox. The remainder is delivered into the
"Firedome" combustion package where the "Secondary
Combustion", or re-burning of the smoke, occurs.
During combustion, the burning of wood proceeds
through several stages. The initial or evaporation stage
is where the moisture in the wood is driven off in the
form of steam. A second stage is where the volatile
gases contained in the wood are released and burned.
This represents most of the wood's heating capacity.
The final stage is the charcoal stage where the charcoal
burns the remaining heat content in the wood fuel. Ash
remains after the burning is complete. Within the primary
firebox two or more of these stages of combustion are
occurring at once.
Before opening, always check for wood, embers, or
ash that may be ready to fall out of the door.
To open the glass door, open the bypass damper
first, then turn the handle clockwise and pull out; to
close the door, push the door closed with the handle
in the open position, then turn, counter-clockwise, to
engage the latch.
Ash Door
To open the ash door, lift up the handle and pull out.
Close the door by pushing in and pushing the handle
all the way down.
Top Load Door
To open the top load door, open the bypass damper
and then lift to open the top load door.
All doors must be closed while the stove is in normal
operation, and the gaskets routinely examined for wear
and replaced when necessary. Good door seals are
important for maintaining control of the stove. Never
operate with the ash door open. Operating the stove with
the ash door open, or with a door inadequately sealed,
could create a serious overfiring condition (discussed
later in this section).
The glass used in your Oakleaf is manufactured
to exact standards to withstand the high heat of the
fire, but like all glass, it must be treated with common
sense and care. Never abuse the glass by slamming
the door shut or striking the glass with a heavy object.
If the glass is broken or damaged, do not operate the
stove until it has been replaced
Always be sure to provide adequate ventillation
to the room where the apliance is located, to prevent
air starvation. In tight construction, consider installing
outside air to the appliance.
(See instructions in the Maintenance section.)
3. grates
EXHAUST STREAM
The Harman Oakleaf's unique grate system
consists of one flat bottom grate, and two front
andirons. The bottom grate has slots which
allow the ash to fall into the ash pan by passing
a poker back and forth across the grate. The
andirons keep the fuel from coming into direct
contact with the glass, and keep hot coals and
embers from spilling out while reloading. Never
build a fire directly against the glass.
The grates and andirons must remain
in place at all times. do not tamper with
or change the configuration of this grate
system.
SECONDARY AIR
THRU BRICK
SECONDARY AIR THRU
RAMP BRICK
SECONDARY AIR ENTERING
EXHAUST STREAM
PRIMARY AIR FLOW
SECONDARY AIR FLOW
PRIMARY & SECONDARY AIR FLOW
25
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
For low burn, slide the air control to the left. For
medium burns, use notches 1 to 2. Maximum heat is
attained with the air control all the way to the right. Do
not burn the stove continuously at the maximum setting.
If maximum heat is required day after day, the stove is
too small for the area you are trying to heat.
If your wood is not seasoned long enough or is high
in moisture content, you may need to adjust the primary
air slightly higher to sustain a low burn rate with the
cleanest possible exhaust.
d. user Controls
Two important controls - the damper bypass handle
and the air control lever regulate the operation and
output of the stove.
To open the top or front loading door, you must open
the damper bypass, or smoke will come in the room. In
this mode of operation the combustion gases go directly
from the main combustion chamber to the flue collar
and exit into the chimney.
NOTE: The bypass damper must be open for
smokeless loading. Open the bypass damper by
turning the handle clockwise while facing handle.
E. Before your first fire
•
Be sure the appliance is installed properly and
that all safety requirements have been met.
Pay particular attention to the clearances to
combustibles, floor protection and the venting
instructions.
•
•
•
Test your smoke detector(s) and CO detector(s)
to the specifications of the manufacturer.
Double check that the ash pan and internal
firebox are empty.
Bypass Damper
Bypass Damper
Closed
Open
Be sure to read this entire manual.
dO NOT OvERLOad THE appLIaNCE. dOORs MusT
BE CLOsEd WHEN IN OpERaTION.
f. Building and Maintaining a fire
Begin with the bypass damper open, and the air
control lever at the maximum setting, all the way to the
right. Be sure the ash pan door is closed and latched.
Start with a bed of crumpled paper and kindling sized
about finger width; place several 1" - 2" (25mm - 50mm)
split pieces of dry wood on top of the kindling, followed by
a few 2" - 3" (50 mm - 80 mm) split pieces. Lay the wood
in a crossed pattern to allow maximum air flow. Ignite
thepaper and close the loading door(s).Allow this start-
up fire to burn for a few minutes, keeping the bypass
damper open. Add about five more pieces of wood in
the 2 to 3 inch (50 - 80mm) size range, making sure
that the fuel bed is all the way across the firebox and
staggered to allow airflow. Close the door and allow this
loading to burn a few minutes.
Minimum
Primary Air
Maximum
Primary Air
Add increasingly larger pieces of wood to the fire until
you have a thick bed of hot embers, approximately 2
to 3 inches deep at the back of the grate and at least
an inch deep at the front. You must have this charcoal
bed established before you close the bypass damper.
The air control lever is located directly below the load
door. Sliding this lever allows you to vary the amount
of air to the fire, creating a range of heat outputs. The
lowest heat output setting is to the left, and the highest
is to the right. The notches are provided as a reference
for your comfortable heat settings. Do not, under any
circumstances, alter the configuration or operation of
the air control lever.
Providing you have the charcoal bed described,
close the bypass damper by pulling the handle toward
the front of the stove.
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
This will begin the highly efficient mode of operation
where the exhaust gases get re-burned in the secondary
combustion package. If you cannot achieve a charcoal
bed within the first 15 to 20 minutes, your wood is likely
too wet, and you may need to burn the fire longer and/
or hotter to compensate for the extra energy needed to
drive out the moisture. If, after five minutes of burning
with the damper closed, smoke is visible coming from
the chimney, you probably do not have the proper coal
bed. Open the bypass damper and continue with the
process until a significant coal bed is formed.
ashes should be placed in a metal container
with a tight fitting lid. The closed container of
ashes should be placed on a noncombustible floor
or on the ground, well away from all combustible
materials, pending final disposal. If the ashes are
disposed of by burial in soil or otherwise locally
dispersed, they should be retained in the closed
container until all cinders have thoroughly cooled.
Never use the ash disposal container for other trash.
Wood ash can be added to your garden or compost.
CauTION
Always remember to open the bypass damper when
you are loading, this allows the exhaust gases to pass
directly into the flue outlet and reduces the chance of
smoke spillage into the room.
THE sTOvE Is HOT WHILE IN OpERaTION. kEEp
CHILdREN, CLOTHINg aNd fuRNITuRE aWay.
CONTaCT May CausE skIN BuRNs.
NEvER LEavE THE sTOvE uNaTTENdEd If EITHER
THE asH OR LOad dOOR Is OpEN. OvERfIRINg
May REsuLT.
Reloading: Once you have prepared and maintained
a thick charcoal bed, and the secondary combustion is
established, you should be able to reload the stove at
any time by simply opening the bypass damper, then
the load door, adding fuel and closing the door then the
damper. This depends on coal bed size, load size and
moisture content of fuel.
RIsk Of ExCEssIvE TEMpERaTuREs. kEEp asH
dOOR CLOsEd duRINg fIRINg Of THE HEaTER.
Avoid overfiring your stove. Overfiring is a potentially
hazardous situation which can lead to overheating of
combustible materials nearby, damage to the stove, and
in extreme cases, cause a fire. Overfiring is caused by:
1. Too much air flowing through the stove too quickly. 2.
You may have positioned the primary air control lever
too far to the right. 3. Inadvertently leaving the damper
open or 4. Not keeping up with routine maintenance,
such as checking door gaskets for wear.
Overfiring results in excessive fuel consumption, and
may cause parts of the stove or chimney connector to
glow red. If you notice signs of overfiring, reduce the air
supply to the fire, and review the Maintenance section
in this manual.
In the event of a chimney fire, call your local fire
department; make sure everyone is safely out of the
house. Reduce the air intake of the stove as much as
possible using the air control lever; close the bypass
damper to further restrict air flow. Do not throw water
on the fire; this can cause stove damage and create
an even more dangerous situation. Have your chimney
professionally cleaned and inspected before resuming
burning in your stove.
Removing ashes: Before reloading, empty the ash
pan (remember to close the ash door while emptying
the pan). The ashes should be the coolest at this time.
Remove ashes from the fire chamber periodically by
raking a poker across the bottom grates.
Excessive ash buildup can prevent proper venting
of exhaust gases. Do not allow the ash pan to over-fill.
Ash buildup between the ash pan and the bottom of
the grate can cause the grate to overheat and wear
out prematurely.
The Oakleaf is designed to provide access to the ash
pan without the need for opening the main door. Before
opening the ash door
and removing the ash
pan, open the bypass
damper.Wearingheavy
protective gloves,
open the ash door and
remove the ash pan
by pulling it forward by
the handle. Close the
As you begin to operate your stove at higher
temperatures, you will notice a “hot” or unpleasant
smell; this is just the paint going through the curing
process, and will disappear after a few fires.
ash door and damper
bypass before taking
the ashes outside for
safe disposal.
27
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
solid fuel burning spave heaters must be cleaned regularly,
as soot, ash and creosote may accumulate.
service & Maintenance
9
seasonal cleaning
a. Creosote- formation and Need for
Removal;
At least once per year, the stove, venting connectors
and chimney should be thoroughly cleaned. If the areas
are found to have an excessive build up of ash or
creosote, it is recommended to increase the frequency
of the cleaning. This will extend the life of the appliance
and its components.Avacuum specifically designed for
ash is preferred, however a standard shop-style vacuum
with a HEPA filter may also work just fine.
During cleaning, caution must be taken not to
damage the white / gray colored ceramic combustion
package in the rear of the firebox. When using a brush in
the chimney or venting connector, the by-pass damper
should be placed in the open position to help prevent
ash, creosote or other debris from falling down onto
and around the combustion package. This also protects
the top of the combustion package from tool or brush
damage and diverts most of the removed materials
into the firebox for easy clean-up and removal. Once
the venting system has been cleaned, remove the first
section of connector pipe from the appliance flue collar.
Carefully vacuum the ash and debris from around the
sides and top of the combustion package.
When wood is burned slowly, it produces tar and other
organic vapors which combine with expelled moisture
to form creosote. The creosote vapors condense in the
relatively cool chimney flue of a slow burning fire. As a
result, creosote residue accumulates on the flue lining.
When ignited, this creosote makes an extremely hot
fire. The chimney and chimney connector should be
inspected at least once every two months during the
heating season to determine if a creosote buildup has
occurred. If creosote has accumulated, it should be
removed to reduce the risk of a chimney fire.
If you experience a chimney fire; Close the air control
and bypass damper and notify the fire department.
Do NOT apply water to the fire, in the firebox or in
the chimney. Do not operate the appliance until the
chimney and connector have been inspected and
approved by a chimney professional.
Do not burn any fuel other than wood, such as
charcoal, which can cause increased carbon monoxide
production or overfiring. Never use highly volatile
substances in your stove, such as gasoline, which could
cause an explosion.
When solid fuels are burned completely, they produce
water and carbon dioxide. However, in long slow burns,
a substantial amount of carbon monoxide may be
produced. If allowed to build up, carbon monoxide
(which is odorless) can prove fatally poisonous. Proper
ventilation and draft will prevent this from happening.
If you smell smoke, turn up the air control lever setting,
and thoroughly ventilate your dwelling. During future
burns, be careful not to overload the stove with fuel, so
you will not be tempted to constantly operate at a low
air control setting.
The shoe brick must be removed to allow vacuum
access for cleaning the front portion of the combustion
package.
Always use caution when refueling or when
vacuuming the firebox and combustion package. Some
users have damaged their combustion package with
vacuum cleaner tools, and fire pokers.
CAuTion: ALwAysweArFire-resisTAnTgLoves
To operATe The sTove. TheAir ConTroLis hoT
whiLe in operATion.
Other causes of poor ventilation or draft are icing,
exhaust fans, a blocked outside air inlet, and room
air starvation. If your stove is sluggish and you get
occasional odor, check these possibilities and increase
the air flow in your home.
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
2. door glass
B. general Maintenance procedures
1. ash Removal
•
•
frequency: As needed / Weekly
By: User
•
•
frequency: As needed / Every day or two
By: User
Whenever the view of the fire is obstructed, or weekly,
clean the glass using a soft cloth dampened with
standard household glass cleaner.
Wear Leather gloves To prevent skin Burns!
Never spray glass cleaner directly onto hot glass.
apply the cleaner to the cloth then wipe the glass.
Open the ash removal door by lifting upward on the
latch handle, then swing the door open. Pull the ash
pan out of the firebox, using the lip on the front of the
pan. Once the ash pan is removed from the stove, you
can flip the carry handle up for convenience.
If removing ashes while a fire is burning, close and
latch the ash door while disposing of the ashes.
DO NOT leave the appliance unattended with the ash
door open.
fly-ash allowed to accumulate on the glass may
lead to permanent fogging or "crazing" of the
glass.
Inspect the glass and sealing gasket. Replace gasket
as needed. Do not operate the stove with a broken
glass. Replacement glass, which is ceramic glass,
should be obtained only through your Harman dealer.
To replace a broken glass; first be sure to carefully
remove the broken glass and any remaining shards or
pieces. With the door laying on a flat surface, lay the
gasketted glass panel onto the door and be sure it is
properly fitted into the channel. Lay the glass retainer
clips in place near each corner, and secure them using
the 3/8" screws. Be sure to tighten each screw equally
so you don't create a pressure point on the glass.
CAuTion: never use AbrAsive mATeriALs on
The gLAss.
Glass Retainers
Glass Panel
ashes must be placed in a metal container with
a tight fitting lid. The closed container of ashes
should be placed on a non-combustible floor or
on the ground, well away from all combustible
materials, pending final disposal. If the ashes are
disposed of by burial in soil or otherwise locally
dispersed, they should be retained in the closed
container until all cinders have thoroughly cooled.
do not use the ash container for other debris or
yard waste.
Glass Retainer
screws
Gasket
Door Frame
WaRNINg: dO NOT aBusE gLass By sTRIkINg
OR sLaMMINg THE dOOR CLOsEd. THIs TypE Of
BREakagE Is NOT COvEREd By THE pROduCT
WaRRaNTy.
29
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
3. firebox
5. Chimney Connector
•
•
frequency: As necessary / Yearly
By: User
•
•
frequency: As necessary / Yearly
By: Qualified Service Technician / User
Cleaning the firebox and internal heat exchange
surfaces is recommended to maintain thermal
efficiency. Depending on the quality and quantity
of fuel being used, you may want to perform this
cleaning monthly.
At the end of the burn season, brush and clean all
sections of chimney connector pipe. Some owners
remove the chimney connector for the off season.
Any ashes left in the connector pipe will actually draw
moisture which promotes rust. This is why it is very
important to clean all ashes at the end of the heating
season.
When cleaning the chimney connector above the
appliance, keep the bypass damper in the open
position. This will keep any loosened material from
falling into the Firedome combustion chamber.
Be sure to clean these areas thoroughly at the end of
the heating season.
Brush and vacuum all internal surfaces at the end
of the heating season. Ashes will draw moisture and
may promote rust formation.
4. Blower- If installed
Chimney
Connector
•
•
frequency: As necessary / Yearly
By: User
The fan on the blower will collect debris over time.
Any accumulation must be removed to maintain
proper operation.
To clean blower;
•
•
Disconnect power cord before servicing.
Remove the two bolts that hold the blower in
place.
6. Chimney
•
•
Use a vacuum and/or brush to remove all dust
and pet hair from the blower wheel.
Reinstall the blower and tighten the two bolts
securely.
•
•
frequency: As necessary / Yearly
By: Qualified Service Technician / Chimney
Sweep
The entire chimney should be professionally cleaned
at least once yearly. It is best to have this done at
the end of the heating season to be sure all ash is
removed. You'll also want to inspect the condition of
the chimney prior to using the appliance, to be sure
there are no bird or animal nests.
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
Reference Materials
10
1
2
31
Save These Instructions
3-90-798
Dry Seasoned Wood Only!
Download from Www.Somanuals.com. All Manuals Search And Download.
service parts
Oakleaf
Beginning Manufacturing date: sept 2010
Ending Manufacturing date: active
Cast Iron Wood stove
1-90-797000-1 (Black),
((sept 2010 thru june 2011)--1-90-797000-2 (Charcoal), 1-90-797000-3 (goldenfire))
3
1
4
2
5
10
7
11
6
9
28
27
12
8
13
14
25
23
22
21
15
26
16
24
18
19
17
20
part number list on following page.
12/11
Download from Www.Somanuals.com. All Manuals Search And Download.
service parts
Oakleaf
Beginning Manufacturing date: sept 2010
Ending Manufacturing date: active
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
stocked
at depot
ITEM
dEsCRIpTION
COMMENTs
paRT NuMBER
2-00-797053P
1-00-797066
1-10-249109
1-00-00999
Heat Shield-Upper Top
Heat Shield-Upper Rear
Oak Flue Collar Cover w/Gasket
Gasket-3/8 Round LDPSA
Oak Flue Collar
1
2
10 Ft
y
y
3
4
4-00-249108D
1-00-2312
Gasket-1/4 Round PSA
Oak Top Load Door
15 FT
3-00-249115P
1-00-797067
1-00-37525
Load Door Handle Kit
Gasket-3/8 Round LD, Top Load Door
Inside Plate-Left w/Gasket
Gasket-1/4 Round PSA
Oakleaf Package
5
6
5 Ft
y
1-10-797104
1-00-2312
15 Ft
15 FT
15 FT
y
y
y
y
y
y
y
y
y
y
y
y
y
y
7
8
3-40-797022
1-00-2312
Gasket-1/4 Round PSA
Ramp Assembly w/Gsket
Gasket-1/4 Round PSA
Brick Clip Set
1-10-797109
1-00-2312
9
1-00-249153
1-10-797103A
1-00-249142
3-50-00500S
4-00-797113
1-10-797036W
1-00-2312
10
Damper Frame Assembly
Damper Adjustment Kit
Damper Handle
Damper Plate
Damper Rod
Gasket-1/4 Round PSA, Damper Plate
Gasket-3/8 Round LD, Damper Frame
Screw-SSSKN5/16-18 X 3/8
Side Left
15 FT
5 Ft
1-00-37525
Pkg of 25
3-30-2004-25
3-00-797107
1-00-37525
11
Gasket-3/8 Round LD
Oak Andiron, Painted
Brick Set, 9" x 4 1/2" x 1 1/4"
Grate
5 Ft
y
y
y
y
12
13
14
15
16
17
3-00-249101P
1-00-900450125
2-00-797023B
1-10-797010
1-10-797013
1-10-797110
1-00-37525
Pkg of 7
Airslide
Airslide shaft
Ash Door Assembly
Gasket-3/8 Round LD
Wooden Knob, Ash Door
5 Ft
y
3-40-08746-3
Additional service part numbers appear on following page.
12/11
Download from Www.Somanuals.com. All Manuals Search And Download.
service parts
Oakleaf
Beginning Manufacturing date: sept 2010
Ending Manufacturing date: active
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
stocked
at depot
ITEM
dEsCRIpTION
Door Assembly, Front
COMMENTs
paRT NuMBER
1-10-797108
3-40-797025
1-00-00249
1-00-2312
18
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
Door Glass
Handle Assembly
Gasket-1/4 Round PSA, Glass Gasket
Gasket-3/8 Round LD, Door Gasket
Glass Clips and Hardware
15 FT
5 Ft
1-00-37525
1-00-249140
1-10-797026
4-00-249100P
3-30-1134-50
3-30-4001-25
3-30-8005-100
3-40-797020
1-00-2312
19
20
Ash Pan
Leg Painted
Screw-HCS 3/8-16 X 1 Z
Pkg of 50
Pkg of 25
Pkg of 100
Bolt-CB 5/16-18 X 2 Z
Nut-FHN 5/16-18 Z 5
21
22
23
Center Brick
Gasket-1/4 Round PSA
Brick 12 X 6 X 1-1/4
Brick Clip
15 FT
1 Set
3-40-86125
1-00-249172
1-10-797034
1-00-10050
1-00-2312
Center Seal Plate, w/Gasket
Gasket 1-1/2X3/8 BULBPSA, Center Plate
Gasket-1/4 Round PSA
Side Right
5 Ft
y
y
15 FT
24
25
26
3-00-797111
1-00-37525
1-10-797112
1-00-2312
Gasket-3/8 Round LD
Inside Plate, Right, w/Gasket
Gasket-1/4 Round PSA
Blower Assembly (Option)
Blower
5 Ft
y
y
15 FT
1-00-797032
1-00-7000537
3-20-06652
3-20-408412
1-10-797045
2-00-797033W
y
y
y
Power Cord
Snap Disc
27
28
Adapter, Pipe
Heat Shield, Lower Rear
12/11
Download from Www.Somanuals.com. All Manuals Search And Download.
Manufactured by: HarMan HOMe HeatInG MOdel: Oakleaf
u.S. envIrOMental PrOtectIOn aGency
Meets EPA particulate matter (smoke) control requirements for noncatalytic
wood heaters built on or after July 1, 1990.
SMOke
0
Grams Per Hour
8.5
effIcIency
50%
60%
70%
80%
90%
100%
Wood heaters with higher efficiencies cost less to operate.
Heat OutPut
9,600 to 24,700 btu
use this to choose the right size appliance for your needs.
aSk dealer fOr HelP.
This wood heater will achieve low smoke output and high efficiency only if
properly operated and maintained. See owner’s manual.
#3-90-799
Download from Www.Somanuals.com. All Manuals Search And Download.
Hearth & Home Technologies Inc.
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for
HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered compo-
nents manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts Labor
HHT Manufactured Appliances and Venting
EPA
Components Covered
Gas
X
Wood Pellet
Coal Electric Venting
Wood
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
1 Year
X
X
X
X
X
X
Igniters, electronic components,
and glass
X
X
X
X
X
X
2 years
X
X
X
Factory-installed blowers
Molded refractory panels
3 years
X
X
Firepots and burnpots
Castings and baffles
5 years 1 year
X
X
Manifold tubes,
HHT chimney and termination
7 years 3 years
X
X
10
1 year
years
X
X
X
Burners, logs and refractory
Firebox and heat exchanger
Limited
3 years
Lifetime
X
X
X
X
X
X
X
X
All replacement parts
beyond warranty period
90 Days
X
X
See conditions, exclusions, and limitations on next page.
4021-645C 12-29-10
Page 1 of 2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CONDITIONS:
•
This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of
HHT authorized dealers is available on the HHT branded websites.
•
•
This warranty is only valid while the HHT appliance remains at the site of original installation.
Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service
from a dealer other than the dealer from whom you originally purchased the product.
•
Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges
for parts are not covered by this warranty.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
•
•
•
Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.
Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, light bulbs, batteries and the discolor-
ation of glass.
•
•
Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and com-
plaints related to this noise are not covered by this warranty.
Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper opera-
tion, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/
incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting
caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or
forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7)
installation or use of components not supplied with the appliance or any other components not expressly authorized
and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing;
and/or (9) interruptions or fluctuations of electrical power supply to the appliance.
•
•
•
Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.
Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.
HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Informa-
tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consider-
ation must be given to appliance location and configuration, environmental conditions, insulation and air tightness of
the structure.
This warranty is void if:
•
The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging
chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel finishes.
•
•
The appliance is subjected to prolonged periods of dampness or condensation.
There is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
LIMITATIONS OF LIABILITY:
•
The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.
This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.
4021-645C 12-29-10
Page 2 of 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Oakleaf Woodburning stove
service & Maintenance Log
Date Of Service
Performed By
Description Of Service
Dry Seasoned Wood Only!
3-90-798
Save These Instructions
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
At Harman, we build each product to a standard, not a price.
This powerful heating appliance boasts uncompromising
attention to detail and helps preserve our planet by using
environmentally responsible fuels.
(Signature of Boxer)
Your premium quality hearth product designed and assembled
by the experienced and skilled members at Harman in Halifax,
PA, USA.
Proudly Printed On 100% Recycled Paper
Download from Www.Somanuals.com. All Manuals Search And Download.
|