DVD 38
DVD AUDIO/VIDEO PLAYER
WITH HDMI™
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
water, then a fresh cloth with clean water. Wipe it dry immediately with a dry cloth.
NEVER use benzene, aerosol cleaners, thinner, alcohol or any other volatile cleaning
agent. Do not use abrasive cleaners, as they may damage the finish of metal parts.
Important Safety Information
Verify Line Voltage Before Use
Avoid spraying insecticide near the unit.
Your DVD 38 has been designed for use with 110–240-volt AC current, and the
plug is specifically designed for 120-volt applications. Connection to a line voltage
other than that for which the plug is intended can create a safety and fire hazard
and may damage the unit.
Moving the Unit
Before moving the unit, be certain to disconnect any interconnection cords with other
components, and make certain that you disconnect the unit from the AC outlet.
If you have any questions about the voltage requirements for your specific model, or
about the line voltage in your area, contact your selling dealer before plugging the unit
into a wall outlet.
NOTE: To avoid damage to the DVD 38 that may not be covered by the warranty,
be certain that the disc is removed from the unit before it is moved. Once the DVD
38 is installed, a disc may be left in the unit when it is turned off, but the unit should
NEVER be moved with a disc left in the disc tray.
Do Not Use Extension Cords
To avoid safety hazards, use only the power cord attached to your unit. We do not
recommend that extension cords be used with this product. As with all electrical
devices, do not run power cords under rugs or carpets or place heavy objects on
them. Damaged power cords should be replaced immediately by an authorized service
center with a cord meeting factory specifications.
Important Information for the User
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. The limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio-frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communication. However, there is no guarantee that harmful interference will
not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC outlet, always pull the plug; never
pull the cord. If you do not intend to use the unit for any considerable length of time,
disconnect the plug from the AC outlet.
Do Not Open the Cabinet
There are no user-serviceable components inside this product. Opening the cabinet
may present a shock hazard, and any modification to the product will void your
guarantee. If water or any metal object such as a paper clip, wire or staple accidentally
falls inside the unit, disconnect it from the AC power source immediately, and consult
an authorized service center.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Installation Location
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept interference received, including interference that may cause
undesired operation.
• To ensure proper operation and to avoid the potential for safety hazards, place
the unit on a firm and level surface. When placing the unit on a shelf, be certain
that the shelf and any mounting hardware can support the weight of the product.
• Make certain that proper space is provided both above and below the unit for
ventilation. If this product will be installed in a cabinet or other enclosed area,
make certain that there is sufficient air movement within the cabinet. Under some
circumstances, a fan may be required. The unit should be placed on its own shelf,
not directly on top of another component.
NOTE: Changes or modifications may cause this unit to fail to comply with Part 15 of
the FCC Rules and may void the user’s authority to operate the equipment.
CAUTION: The DVD 38 uses a laser system. To prevent direct exposure to the laser beam,
do not open the cabinet enclosure or defeat any of the safety mechanisms provided for
your protection. DO NOT STARE INTO THE LASER BEAM. To ensure proper use of this
product, please read this Owner’s Manual carefully and retain it for future use. Should the
unit require maintenance or repair, please contact your local Harman Kardon service center.
Refer servicing to qualified personnel only
• Do not place the unit directly on a carpeted surface.
• Avoid installation in extremely hot or cold locations, or in an area that is
exposed to direct sunlight or heating equipment.
• Avoid moist or humid locations.
Unpacking
• Do not obstruct the ventilation slots on the unit, or place objects directly
over them.
The carton and shipping materials used to protect your new receiver during shipment
were specially designed to cushion it from shock and vibration. We suggest that you
save the carton and packing materials for use in shipping if you move, or should the
unit ever need repair.
• Due to the heat generated by operation of the DVD 38 and other components
in your system, there is the remote possibility that the rubber padding on the
bottom of the unit’s feet may leave marks on certain wood or veneer materials.
Use caution when placing the unit on soft woods or other materials that may
be damaged by heat or heavy objects. Some surface finishes may be particularly
sensitive to absorbing such marks, due to a variety of factors beyond Harman
Kardon's control, including the nature of the finish, cleaning materials used, and
normal heat and vibration caused by the use of the product, or other factors. We
recommend that caution be exercised in choosing an installation location for the
component and in normal maintenance practices, as your warranty will not cover this
type of damage to furniture.
To minimize the size of the carton in storage, you may wish to flatten it. This is
done by carefully slitting the tape seams on the bottom and collapsing the carton. Other
cardboard inserts may be stored in the same manner. Packing materials that cannot be
collapsed should be saved along with the carton in a plastic bag.
If you do not wish to save the packaging materials, please note that the carton
and other sections of the shipping protection are recyclable. Please respect the
environment and discard those materials at a local recycling center.
It is important that you remove the protective plastic film from the front-panel lens.
Leaving the film in place will affect the performance of your remote control.
Cleaning
When the unit gets dirty, wipe it with a clean, soft, dry cloth. If necessary, and only after
unplugging the AC power cord, wipe it with a soft cloth dampened with mild soapy
3
Download from Www.Somanuals.com. All Manuals Search And Download.
STAPLE INVOICE HERE
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
2 SAFETY INFORMATION
6 INTRODUCTION
7 DISC COMPATIBILITY
8 FRONT-PANEL CONTROLS
10 FRONT-PANEL INFORMATION DISPLAY
11 REAR-PANEL CONNECTIONS
13 REMOTE CONTROL FUNCTIONS
16 INTRODUCTION TO HOME THEATER
17 CONNECTIONS
17
17
17
18
18
18
19
Audio Connections
Digital Audio
Analog Audio
Video Connections
Digital Video
Analog Video
Remote IR Input and Output
20 INSTALLATION
20
20
20
21
21
22
Step One – Connect the DVD 38 to Other Components
Connecting the DVD 38 Directly to a Television
Connecting the DVD 38 to an Audio/Video Receiver
Step Two – Plug In AC Power
Step Three – Insert Batteries in Remote
Step Four – Turn On the DVD 38
23 INITIAL SETUP
23
24
25
27
28
29
Using the On-Screen Menu System
Step One – System Setup
Step Two – Audio Setup
Step Three – Audio Adjustments
Step Four – Video Setup
Step Five – Video Adjustments
32 OPERATION
32
32
35
39
41
43
44
Turning On the DVD 38
Playback Basics
DVD Playback
CD Playback
MP3, Windows Media and JPEG Playback
VCD Playback
Programming a Playlist
45 TROUBLESHOOTING GUIDE
47 TECHNICAL SPECIFICATIONS
47
Trademark Acknowledgments
48 GLOSSARY
50 APPENDIX
WARNING
To prevent fire or shock hazard, do not expose this appli-
ance to rain or moisture.
For Canadian model
This Class B digital apparatus complies with Canadian
ICES-003.
For models having a power cord with a polarized plug:
CAUTION: To prevent electric shock, match wide blade
of plug to wide slot, fully insert.
Modèle pour les Canadien
Cet appareil numérique de la Classe B est conforme
à la norme NMB-003 du Canada.
Sur les modèles dont la fiche est polarisee:
ATTENTION: Pour éviter les chocs électriques, introduire
la lame la plus large de la fiche dans la borne
correspondante de la prise et pousser jusqu’au fond.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Note: You’ll need the product’s serial number. At the same time, you can choose to be notified about our new products
and/or special promotions.
WWW.HARMANKARDON.COM
Thank you for choosing Harman Kardon®!
The DVD 38’s user-friendly on-screen menus are easy to use, and high-
performance features, such as pixel-by-pixel video processing and true
3/2 pulldown reconstruction of film-based programming, make using it a
Harman Kardon invented the audio receiver more than 50 years
pleasure. With the ability to play almost any disc in your library, including
ago, and in the intervening years we have witnessed amazing advances
DVD Audio/Video, DVD R/RW, CD-R/RW, MP3, WMA, VCD and JPEG,
in consumer electronics. With our line of high-performance DVD players,
Harman Kardon offers a complete home theater solution: source DVD
the DVD 38 is bound to be enjoyed for many years to come.
To obtain the maximum enjoyment from your new DVD player, we
urge you to read this manual and refer back to it as you become more
familiar with its features and their operation.
player, audio/video receiver and loudspeakers. The DVD 38 features a
variety of standard connections that make it compatible with almost any
home theater component available. Whether your television is a CRT or
the latest high-definition digital flat-screen display, the DVD 38 offers a
range of video outputs, including Simplay HD™-verified HDMI™, each of
which delivers stunning picture quality to match your display’s capabilities.
If you have any questions about this product, its installation or its
operation, please contact your retailer or customer installer, or visit our
DVD 38 DVD Audio/Video Player With HDMI™
Outputs
• Internal video test signal
• Digital audio: Coaxial and optical
• Analog audio: 2-channel and 6-channel
• Digital Audio/Video: Simplay HD-verified HDMI
• Analog Video: Composite, S-video and component
• Remote Control IR: Input and Output
• Fast Play: 2x, 4x, 8x, 20x, 100x
• Slow Play: 1/2x, 1/4x, 1/8x, 1/16x (1/2x and 1/4x only in reverse)
• Zoom (DVDs and JPEGs): 2x, 3x, 4x, 5x (VCDs: 2x, 3x)
• Random Play (CDs, MP3s, WMAs only)
• Repeat Play: 1 group/title, 1 track/chapter, 1 folder, 1 disc, 1 playlist
• A-B Repeat Play (DVDs, CDs and VCDs only)
• Parental control system with user-programmable password
• Disc recognition for up to five discs
Ease of Use
• Graphic user interface with composite, S-video,
component video and HDMI
• Playback control for VCDs
• Aspect-ratio adjustment
• Dot-matrix front-panel display
• Color-coded connections
• Backlit remote control
Supplied Accessories
The following accessory items are supplied with the DVD 38. If any
of these items is missing, please contact Harman Kardon customer
The DVD 38 is Simplay HD-verified for compatibility
via the HDMI connection with other Simplay HD-verified products.
DVD Player
• System remote control
• Plays 5-inch (12cm) and 3-inch (8cm) discs
• Video formats supported: DVD, DVD-R/RW, DVD+R/RW, VCD
• Two AAA batteries
• HDMI cable
• Audio formats supported: DVD-Audio, CD, CD-R/RW, MP3,
• A/V cable for stereo analog audio and composite video
• S-video cable
• Mini-plug remote interconnect cable
Windows Media® WMA
• Still-image formats supported: JPEG, Kodak® Picture Disc
• Video upscaling to 720p and 1080i via HDMI output
• MP3 bit rates: 32kbps – 320kbps
1
NOTE: This player is designed and manufactured for compatibility with
Region Management Information that is encoded on most DVD discs.
This player is designed only for playback of discs with Region Code 1,
or for discs that do not contain Region Code information. If there is any
other Region Code on a disc, that disc will not play in the DVD 38.
• WMA bit rates: 64kbps – 320kbps
• JPEG files: 5 megapixels, 5MB file size, up to 250 files per disc
• Still-image rotation in 90-degree increments
• Thumbnail still-image menu
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC COMPATIBILITY
Disc Formats Supported by This Player
The DVD 38 can play the following types of prerecorded discs:
• Linear PCM, MP1 (MPEG-1, Layer 1), MP3 (MPEG-1, Layer 3)
digital audio
• MPEG-1 digital video
• May contain JPEG still images (Video CD Version 2.0).
AUDIO/VIDEO
• Some discs may contain menus and chapters, while other discs
simply contain tracks. Version 2.0 discs may offer interactive playback
control (PBC).
DVD
3" (8cm) disc
5" (12cm) disc
CD
3" (8cm) disc
5" (12cm) disc
The DVD 38 will NOT play the following:
• DVD discs with a Region Code other than 1 or 0
• DVD-ROM data discs
• DVD-RAM discs
The DVD 38 will also play most recordable discs, but we cannot
guarantee complete playback compatibility due to the wide variation in
recorders and blank discs.
• CD-I discs
• CD-G discs
ReWritable
CD-RW
5" (12cm) disc
CD-R
3" (8cm) disc
5" (12cm) disc
VCD
5" (12cm) disc
• SVCD discs
• Kodak Photo CD™ discs (Kodak Picture CD discs, available to
consumers, may be viewed using the DVD 38)
DVD-Video Disc Compatibility:
• 3" (8cm) or 5" (12cm) discs
• Single-sided or double-sided discs
• Single-layer or dual-layer discs
• Discs intended for use in video game consoles
• Discs recorded in the “VR” mode or at any speed other than “SP”
• High-definition optical discs such as WMVHD, SACD,™ HD-DVD™
and Blu-ray Disc™
• Dolby® Digital, DTS®, MPEG or Linear PCM digital audio tracks
• MPEG-2 digital video
NOTES:
Due to differences in the authoring of certain discs, it is possible
that some discs may include features that are not compatible with
the DVD 38. Similarly, although the DVD 38 is capable of a wide
range of features, not all discs include every capability of the DVD
system. For example, although the DVD 38 is compatible with
multiangle discs, that feature is only possible when the disc is
specially encoded for multiple-angle play. To make certain that
a specific feature or soundtrack option is available, please check
the options listed on the disc jacket.
• Discs are generally divided into one or more titles, which may be
further subdivided into chapters.
DVD-Audio Disc Compatibility
• 3" (8cm) or 5" (12cm) discs
• Single-sided discs
• Single-layer or dual-layer discs
• Linear or packed PCM digital audio
• Some discs may contain MPEG-2 video, and Dolby Digital, DTS
or MPEG digital audio.
• Discs are generally divided into one or more groups, which may
be further subdivided into tracks.
• Playback of DTS audio discs requires connection to a processor
or receiver with a DTS decoder and the correct setting of the
Digital Output in the AUDIO SETUP Submenu to”Bitstream”
(see page 26).
Audio CD Compatibility
• 3" (8cm) or 5" (12cm) discs
• Linear PCM digital audio
• Playback of CD-R/RW and DVD R/RW discs created on a
computer requires proper formatting and finalization of the disc.
• The DVD 38 is compatible with most discs recorded with files
encoded using MP3 or Windows Media 9 (up to 320kbps), as
well as JPEG still images. However, variations in the encoder or
codec used and the bit rate of the encoding may affect the
DVD 38’s ability to play a specific disc. As a result, we cannot
guarantee complete compatibility with all encoders and versions
of the codecs. For best results, we recommend that MP3 files
be encoded at bit rates ranging between 32kbps and 320kbps.
WMA files should be encoded at bit rates between 64kbps and
320kbps. Although the DVD 38 is capable of playing some
WMA 9 files, not all features of version 9 are supported. JPEG
files should contain no more than 5 megapixels, and the file size
should be no larger than 5MB.
• Audio CDs are divided into tracks
CD-R/RW Compatibility
• 5" (12cm) discs
• Linear PCM, MP3 (32kbps – 320kbps) or Windows Media WMA
(64kbps – 320kbps) digital audio
• May contain JPEG still images (up to 5 megapixels, file size up to
5MB, limit of approximately 250 files per disc).
• Linear PCM discs are generally divided into tracks like an audio CD.
MP3, WMA and JPEG discs (or discs that contain more than one
of these formats) are divided into files, which may be organized into
folders, depending on how the disc was created.
VCD Compatibility
• 5" (12cm) discs
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT-PANEL CONTROLS
Standby/On Switch: This electrical switch turns the DVD 38 on
for playback, or leaves it in Standby mode for quick turn-on using this
switch or the remote control.
Skip/Search Forward: Each press advances to the next chapter
or track. Press and hold for fast search forward within the current
chapter or track at the speed indicated on-screen.
Power Indicator: This LED is next to the Standby/On Switch. When
the DVD 38 is plugged into AC power, the LED turns amber to indicate
that the DVD 38 is in Standby mode (ready to be turned on). When the
DVD 38 is turned on (by pressing the Standby/On Switch), the LED
turns blue. If this LED ever turns red, immediately unplug the DVD 38.
Check the wire connections. If the LED remains red, bring the DVD 38
to an authorized Harman Kardon service provider.
Remote IR Sensor: This sensor receives infrared commands from
the remote control. It is important to ensure that it is not blocked. If
covering the sensor is unavoidable, such as when the DVD 38 is placed
inside a cabinet, you may use an optional Harman Kardon HE 1000,
or other infrared receiver, connecting it to the Remote IR Input on the
DVD 38’s rear panel. Alternatively, connect the Remote IR Output of
another compatible component, such as a Harman Kardon AVR, to
the DVD 38’s Remote IR Input. Point the remote at the other device’s
remote sensor, and the command will be transmitted to the DVD 38.
An external IR “blaster” may also be used, positioned to point at this area.
Open/Close: Press this button to open or close the disc drawer.
When the DVD 38 is in Standby mode, press this button to turn it on
and open the drawer. Before pressing this button, always make sure
no objects are blocking the drawer. Remember to close the door or
turn off the DVD 38 when you have finished. The door will close auto-
matically after five minutes.
Dimmer: Some people find the front-panel display distracting,
especially while watching a movie. Each press of this button cycles
through the front-panel brightness options of Full Brightness, Half
Brightness and Off. The Power Indicator always remains lit to remind
you that the DVD 38 is turned on, but the display will remain dimmed
or off, even when a command is entered.
Message Display: Various messages appear in this display
in response to commands. In addition, a variety of indicators will
light at various times to display the current playback mode, video
settings or other aspects of the DVD 38’s status.
Open/Close: Press this button to open or close the disc drawer.
Disc Drawer: This drawer holds a disc that is played in the DVD 38.
Press the Open/Close Button to access it. Be sure to carefully seat all
discs in the recess in the drawer tray. To avoid damaging the drawer
accidentally, do not press down on it when open. The drawer will close
automatically after five minutes of inactivity to prevent dust or dirt from
entering the DVD 38 and to prevent damage. If a disc is present, it will
begin playing.
Play: Press to start playback of a loaded disc, or to resume play after
the disc has been paused.
Pause: Press to pause play, or to resume after play has been momen-
tarily paused. When a DVD is playing, a still image of the frozen action
will appear on-screen. In Pause mode, you may access the Frame-by-
Frame Advance and Slow Search functions by pressing the forward or
reverse Step or Skip Buttons on the remote. The Disc Recognition
function is not activated by Pause mode.
Stop: Press once to stop play and enter Resume mode, in which
pressing Play resumes playback from the point at which it was stopped.
Press this button twice to fully stop play of the disc. The Disc
Recognition function is activated by Resume mode, enabling you to turn
off the player or change discs, then resume play from the point at which
it was stopped the next time the disc is loaded. Resume mode is not
available for WMA files or VCDs without playback control.
Skip/Search Reverse: Press once to return to the beginning of
the current chapter or track. Quickly press again to skip to previous
chapters or tracks. Press and hold for fast search reverse within the
current chapter or track at the speed indicated on-screen.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT-PANEL CONTROLS
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT-PANEL INFORMATION DISPLAY
Playback
Control
Random
Repeat
Program
A-B
Repeat
Video
Resolution
Audio
Bitstream
Camera
Angle
Parental
Lock
Video Off
Disc-Type
Group/Title
Playback
Mode
Chapter/Track
Time
NOTE: To make it easier to follow the instructions that refer to the controls and connectors in this illustration, a larger copy may be downloaded
Disc-Type Indicators: The DVD, DVD-Audio, CD, VCD, MP3, WMA using the VIDEO SETUP menu, or by pressing the HD Mode Button
or JPEG indicator will light to show the type of disc currently being played. on the remote. This indicator does not reflect the HDMI Mode setting.
Audio Bitstream Indicators: When a Dolby Digital, DTS or Linear
PCM digital audio signal is detected, one of these indicators will light.
DVD-Audio, MP3 and WMA bitstreams will be indicated by the Disc-
Type Indicator.
Time Indicators: These positions show the running time of a disc
in play.
NOTE: These positions will also display text messages about the DVD’s
status, including Loading when a disc is loading, Power Off when the
unit is turned off, and Disc Error when a disc not compatible with the
DVD 38 is loaded.
Parental-Lock Indicator: This indicator lights in red when the
parental-lock system is engaged to prevent changing the rating level
without a code.
Chapter/Track Number Indicators: When a DVD disc is playing, these
two positions show the current chapter. When a DVD-Audio or CD disc
is playing they will show the current track number.
Program Indicator: This indicator lights when a playlist has been
programmed using the menu system (available for CDs only).
Angle Indicator: This indicator blinks when alternative viewing angles
are available on the DVD currently playing.
Group/Title Indicators: These two positions show the current title
number when a DVD disc is playing, or the current group for a DVD-
Audio disc.
Random Indicator: This indicator lights when the unit is in the Random
Play mode.
Playback-Mode Indicators: These indicators light to show the current
playback mode:
A-B Repeat Indicator: This indicator lights when a specific passage
for repeat playback has been selected.
›Lights when a disc is playing in the Normal mode. This indicator
will flash when the disc is in Forward Slow Play mode. The on-screen
banner display indicates the selected speed (1/2x, 1/4x, 1/8x or 1/16x).
VCD Playback Control Indicator: This indicator lights when the
playback control function is turned on for VCDs.
›› When the DVD 38 is in the Fast Search Play mode, two of these
indicators will light to show that the unit is in a Fast Play mode. The
on-screen banner display indicates the selected speed (2x, 4x, 8x, 20x
or 100x). Fast Play mode is not available for WMA files.
Repeat Indicators: These indicators light when any of the Repeat
functions are in use.
Video OFF Indicator: This indicator lights in red when the unit's video
output has been turned off by pressing the Video OFF Button on the
remote control.
Lights when the disc is paused.
‹‹Lights when the disc is in the Fast Search Reverse mode. The
on-screen banner display indicates the selected speed (2x, 4x, 8x, 20x
or 100x). Fast Search Reverse mode is not available for WMA files.
Video Resolution Indicators: One of these indicators will light to
indicate the video resolution of the source DVD, usually 480p. However,
if your video display is capable of handling higher resolutions, the HDMI
Output will upscale to the higher resolution, as indicated in the VIDEO
SETUP menu (explained in the Initial Setup section). You may change
the HDMI Mode setting to a lower resolution to improve picture quality
‹
Flashes when the disc is in Reverse Slow Play mode. The on-screen
banner display indicates the selected speed (1/2x or 1/4x).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR-PANEL CONNECTIONS
Remote Infrared (IR) Input and Output: When the Remote IR sensor
video, select Progressive at the Scan Type setting in the VIDEO SETUP
submenu, or press the P/I Button on the remote repeatedly until the
Progressive Scan setting is selected.
on the front panel is blocked, such as when the DVD 38 is placed
inside a cabinet, connect the IR Output of your receiver/processor or
an optional IR receiver to the Remote IR Input jack for use with the
remote control. The Remote IR Output may be connected to the
Remote IR Input of a compatible source device (or other product) to
enable remote control through the DVD 38. When several devices are
used, connect them in “daisy chain” fashion.
IMPORTANT NOTE: Do not connect the Component Video
Output jacks to standard composite video inputs on any device.
Composite and S-Video Outputs: If your video display does not have
HDMI or component video inputs, connect one of these two video
outputs to your receiver/processor or directly to the display. If available,
S-video is preferred. Do not connect more than one of the DVD 38’s
analog video outputs (component video, S-video, composite video) to
any other device at the same time. You may connect both the HDMI
Output and the Composite Video Output to your receiver if your receiver
distributes composite video through a multiroom system.
HDMI Output: If you have an HDMI-compatible receiver or video
display device, connect this output to an HDMI input on the receiver
or video display for high-quality digital audio and video. Even if your
receiver is not capable of processing audio in the HDMI format, you
will still experience the superb reproduction of HDMI video.
In all cases, the video display must be HDCP-compliant in order to use
the HDMI output. For best results, we do not recommend HDMI connec-
tions in excess of ten feet without a repeater. If your video display has a
DVI input, you may use an optional HDMI-to-DVI cable or adapter for
the connection to the display.
2-Channel Analog Audio Outputs: Connect these outputs to the left
and right analog audio inputs on your receiver/processor or TV. You
may connect these jacks in addition to a digital audio connection, and
it is recommended that you do so as a backup if you wish to use the
DVD 38 as a source device for a multiroom system or if you wish to
make analog recordings, as it is not possible to make digital recordings
of most DVDs.
The DVD 38 is Simplay HD-verified for compatibility via the HDMI
connection with other Simplay HD-verified products.
The following audio formats may be output via the HDMI connection:
Audio CD – 2-Channel PCM or 5.1-channel DTS
DVD-Audio – 2-Channel PCM
6-Channel Analog Audio Outputs: Connect these outputs to the
matching 6-channel analog audio inputs on your receiver or surround
sound processor. This connection is required to listen to the multichannel
tracks on DVD-Audio discs. If the disc also contains a Linear PCM,
Dolby Digital or DTS track, you may listen to it using the HDMI Output,
the Coaxial or Optical Digital Audio Output or the 2-Channel
Analog Audio Outputs.
DVD-Video – Up to 5.1-channel Dolby Digital or DTS
NOTE: To hear the high-resolution surround sound recorded on DVD-
Audio discs, you also need to connect the 6-Channel Audio Outputs
to the corresponding input jacks on your receiver or processor. These
formats are not output digitally.
AC Power Cord: Connect the AC power cord to an AC outlet. If the
outlet is controlled by a switch, make certain that it is in the ON position.
If the cord somehow becomes damaged, contact your authorized
Harman Kardon dealer for a replacement.
To hear a two-channel analog downmix via the 2-Channel Analog Audio
Outputs, select Stereo at the Bass Management setting in the AUDIO
SETUP submenu, or press the Audio Mode Button on the remote repeatedly
until the Stereo setting is selected.
Coaxial and Optical Digital Audio Outputs: If your receiver or
processor has an available digital audio input, connect either of these
digital audio outputs to the corresponding input on the receiver/processor
to enjoy digital audio formats such as Dolby Digital, DTS or standard
PCM (traditionally found on CDs and may be available on other discs).
Never connect both of these outputs to the same device simultaneously.
However, it is okay to connect one of the digital audio outputs plus the
analog audio outputs to the same device.
NOTE: The Coaxial Digital Output should only be connected to a digital
input. Even though it is the same RCA-type connector as standard
analog audio connections, DO NOT connect it to a conventional analog
input jack.
Component Video Outputs: If your television or video display and
receiver are component video-capable, and your display does not have
an HDMI input, connect these jacks to the corresponding inputs on the
receiver or TV that are labeled “Y/Pr/Pb” or “Y/Cr/Cb.” If your video
display is capable of handling resolutions of 480p or better, connect
these outputs to the HD (high-definition) component video inputs on
your display. If the display is capable of displaying progressive-scan
11
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR-PANEL CONNECTIONS
12
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL FUNCTIONS
IR Transmitter Lens: As buttons are pressed on the remote,
infrared codes are emitted through this lens. Make sure it is pointing
toward the component being operated.
Info: Press this button to display the Disc Information screen, which
contains detailed information about the current disc. Press it again to
clear the display. See the Operation section for more information.
Power On: Press this button to turn on the DVD 38 when it is in
Standby mode (plugged in with the Power Indicator lit up in amber).
System Setup: Press this button to access the SYSTEM SETUP
menu. See the Initial Setup section for more information.
Power Off: Press this button to turn off the DVD 38, placing it in
Standby mode.
Disc Menu: Press this button while a DVD is playing to view the
disc’s menu.
Open/Close: Press this button to open or close the disc drawer. If
the DVD 38 is in Standby mode, pressing this button will turn it on.
Status: When a DVD or VCD is playing, press this button to view the
Status Bar, which contains playback mode information.
Audio: Press this button while a DVD is playing to display the current
Transport Controls: These buttons are used to operate the disc
player. Use the controls to skip forward or reverse by track or chapter;
to fast-search forward or reverse; and to play, pause or stop the disc.
After pressing the Pause button, the Skip buttons may be used to step
frame-by-frame through a video presentation, and the Fast-Search
buttons may be used for slow play.
audio track information and to select another audio format.
Clear: Press this button to clear a number you have started to enter.
This button may also be used to clear the on-screen displays. Press
and hold this button for five seconds while in Stop mode and with all
on-screen displays cleared to reset the DVD 38 to its factory-default
settings.
Angle: When a DVD encoded with multiple camera angles is playing
and when the Angle Icon appears to indicate that the multiple-angle
passage has been reached, press this button to cycle through the
various available angles.
Title: This button allows you to select from the titles stored on the disc,
which may include “making of” or other featurettes. Some DVD-Audio
discs may allow you to select from the available audio formats using the
Title Button.
This button is also used to rotate still images. Each press rotates the
image clockwise 90 degrees.
Subtitle: Press this button while a DVD containing subtitle information
is playing to turn subtitles off or select a subtitle language. This setting
will only be in effect for the current disc.
Zoom: When viewing a DVD, VCD or JPEG still image, press this button
repeatedly to enlarge the on-screen image by 2x, 3x, 4x or 5x (2x or
3x only for VCDs) before returning to the original size. While enlarged,
use the Navigation buttons to explore the image.
NOTE: Due to the variations in how DVD discs are authored,
the subtitle languages displayed by the DVD 38 may not accu-
rately reflect the actual languages available on the disc. It is
recommended that subtitles be selected using the disc’s menu.
⁄
/¤/‹/›Navigation and Enter Buttons: These buttons are
used together to make selections within the on-screen menu system.
Backlight: Press this button to turn on the backlight to make it easier
to see the buttons in a darkened room. The backlight will remain on for
a few seconds after your last button press before going out, or you may
turn off the backlight by pressing this button again.
Playlist: Press this button to display the Disc Information screen, which
shows the order in which tracks are currently being played. You may
navigate to the Program screen to program a playlist, in which the
tracks may be played in a different order than they appear on the disc.
See the Programming a Playlist section for more information.
Video Off: Some people prefer to turn off the video display when
listening to audio-only discs. Pressing this button deactivates the video
circuitry, avoiding any possible interference with the audio. Moreover,
plasma and CRT video displays are subject to “burn-in” when a still
image, such as a menu, remains on-screen for more than a short time.
Although the DVD 38 features a screen saver that appears automatically
after a brief period of inactivity, we strongly recommend that plasma
and CRT owners use the Video Off function liberally. Press the button
a second time to reactivate the video displays.
Repeat: Press this button repeatedly to cycle through the Repeat
modes available with the current disc. This button is not used to access
A-B Repeat mode.
A-B Repeat: While a disc is playing, the A-B Repeat function allows
you to repeatedly play a passage, which may include several tracks or
chapters. Press the button once to select the starting point (“A”), and
a second time to select the end of the passage (“B”). Press the button
again to end repeat play.
Random: This button turns on or off Random Play mode, which plays
the tracks on a CD in random order.
Numeric Keys: Use these buttons to directly enter a track or chapter
number to skip to that section of the disc, or to enter a password for the
parental control system.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL FUNCTIONS
IR Transmitter Lens
Power On
Power Off
Open/Close
Audio
Clear
Subtitle
Title
Playlist
Numeric Keys
Repeat
A-B Repeat
Random
Info
Status
Disc Menu
System Setup
Previous Step/Skip
Next Step/Skip
Stop
Search/Slow Reverse
Search/Slow Forward
Transport Controls
Play
Angle
Zoom
Pause
Enter
⁄
⁄/
/‹/›Navigation
Backlight
Video Off
Scan Type
Dimmer
Audio Mode
HD Mode
NOTE: To make it easier to follow the instruc-
tions throughout the manual that refer to this
illustration, a copy of this page may be down-
loaded from the Product Support section at
14
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL FUNCTIONS
Dimmer: Some people find the front-panel displays distracting,
Use the Audio Mode Selector to conveniently select from the
three available settings without having to enter the on-screen
menu system.
especially while watching a movie in a darkened room. Each press of
this button cycles through the Full Brightness, Half Brightness and Off
settings. The Power Indicator will always remain lit to remind you that
the DVD 38 is turned on.
HD Mode: Each time the DVD 38 is turned on while connected via
HDMI to a video display or other device, the DVD 38 and the other
device exchange information about the other device’s video resolution
capabilities. The DVD 38 sets the resolution of the HDMI Output to
match the video display. If the original program materials were recorded
at a much lower resolution, you may wish to change the video output
resolution to improve the picture quality. Press this button to select from
the resolution settings available with your display. You will not be able to
select a resolution greater than your display’s capabilities.
NOTE: Although you may enter commands and operate
the DVD 38 normally even with the front-panel display fully
dimmed, the display will not wake when a command is entered.
To view the display messages, press the Dimmer Button to
change the brightness setting.
Scan Type: Each press of this button toggles between the Progressive-
and Interlaced Scan settings of the Component Video Outputs. It has
no effect on the Composite, S-Video or HDMI Outputs. The button also
has no effect while the SYSTEM SETUP menu is on-screen. Press the
Clear or Setup Button to clear the on-screen displays. Use this button
when your video display is not capable of handling progressive-scan
component video signals, and you have inadvertently selected the
progressive scan setting in the VIDEO SETUP menu.
This button performs the same function as the HDMI Settings line in the
VIDEO SETUP menu. The HDMI Mode setting will not be displayed on
the front panel, which indicates the resolution of the source disc’s video
signal. The HDMI Mode setting may be viewed by accessing the VIDEO
SETUP menu as described in the Initial Setup section.
Audio Mode: This button adjusts the Bass Management setting,
which is also found in the AUDIO SETUP menu. Stop playback of the
current disc in order to use this selector.
There are three available settings: Bypass (the default), On and Stereo.
The first press displays the current setting, and each additional press
cycles through the three settings.
Bypass: The analog audio information is passed through the Analog
Audio Outputs as is, without applying any bass management adjustments.
This mode is used with receivers and processors that are capable of
applying bass management settings (speaker size, output levels and
delay times) to their 6-channel analog inputs.
On: This setting is used with receivers and processors that pass the
audio signals from their 6-channel analog inputs directly to the outputs
without applying any bass management settings. With Bass Management
on, use the AUDIO ADJUSTMENTS submenu to set the DVD 38’s bass
management settings.
Stereo: This mode is used when a 2-channel downmix of a multichannel
audio signal is desired. For example, if you are playing a DVD-Audio
disc, in which case the multichannel presentation is only available
through the Analog Audio Outputs, and you would like to distribute the
program to a multiroom system, select the Stereo mode.
NOTE: The 2-channel downmix (Stereo mode) and the 5.1-
channel presentation of multichannel audio discs (Bypass or
Bass Management On modes) are not available simultaneously.
With Bass Management on, only the front left and right channel
information will be available at both the 2-channel and 6-channel
left and right Analog Audio Outputs. No surround or center
channel information will be present in the signal output at the
2-channel Analog Audio Outputs. In Stereo mode, the down-
mixed 2-channel signal will be available at both the 2-channel
and 6-channel left and right Analog Audio Outputs, while none
of the remaining 6-channel outputs will have any information.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION TO HOME THEATER
The DVD 38 may be the first multichannel surround sound component
you’ve owned. This introductory section will help to familiarize you with the
basic concepts, which may make setup and operation smoother.
in Dolby Digital, contain a special low-frequency effects (LFE) channel
that is directed only to the subwoofer. The LFE channel packs the
punch of a rumbling train or airplane, or the power of an explosion,
adding realism and excitement to your home theater.
If you are already familiar with home theater, you may skip this section
and proceed to the Connections section on page 17.
Surround Modes
Typical Home Theater System
There are different theories as to the best way to present surround
sound and to distribute soundtrack information among the various
speakers. A variety of algorithms have been developed in an effort to
accurately reproduce the way we hear sounds in the real world. The
result is a rich variety of surround mode options. Some modes are
selected automatically, depending on the signal being received from
the source. In many cases, you may select a surround mode manually.
A home theater typically includes your audio/video receiver, which controls
the system; a DVD player; a source component for television broadcasts;
(e.g., a cable box, a satellite dish receiver, an HDTV tuner or simply an
antenna connected to the TV); a video display (TV); and loudspeakers.
All of these components are connected by various types of cables for
audio and video signals.
Several companies have taken surround sound in slightly different
directions. It is helpful to group the numerous surround modes either
by their brand name, or by using a generic name:
Multichannel Audio
The benefit of a home theater system is that several loudspeakers are
used in various locations around the room to produce “surround sound,” • Dolby Laboratories Modes:
immersing you in the musical or film presentation for increased realism.
Í Dolby Digital, Dolby Digital EX – These modes are encoded in
The receiver used with the DVD 38 may have up to seven speakers
connected to it (plus a subwoofer). When more than two speakers are
used, it is called a multichannel system
the program material either on a disc or within a television broad-
cast. They provide up to five or six separate main audio channels
and a dedicated low-frequency effects (LFE) channel.
• Front Left and Right – The main speakers are used the same way
as in a two-channel system. However, you may notice that in many
surround modes, these speakers are used more for ambient sound
while the main action and dialogue are moved to the center speaker.
Í Dolby Pro Logic® II/IIx – These modes are derived by an analog
decoder that creates five or six full-range, discrete main audio
channels from matrix surround-encoded or 2-channel analog
sources. Select from Movie mode, which is optimized for movies
and television programs; Music mode, which is optimized for
music selections; or Dolby Pro Logic, the original version that
steers a mono signal containing information below 7kHz to the
surround channels.
• Center – The center speaker is usually placed above or below the
video screen, and is used mostly for dialogue in movies and television
programs. This placement allows the dialogue to originate near the
actors’ faces, for a more natural sound.
• DTS Modes – DTS is a digital surround format that is encoded in
the program material. It uses a different encoding and decoding
method than Dolby Digital to provide up to 5 discrete main channels,
plus an LFE channel. The DTS-ES (Discrete and Matrix) and DTS
Neo:6® modes offer up to six main channels, either encoded or
derived. DTS 96/24® is a mode encoded in special high-resolution
audio-only discs.
• Surround Left and Right – The surround speakers are used to
improve directionality of ambient sounds. In addition, by using more
loudspeakers in the system, more dynamic soundtracks may be
played without risk of overloading any one speaker.
• Surround Back Left and Right – Additional surround speakers may be
placed behind the listening position, improving the precision with which
ambient sounds may be placed and allowing for more realistic-sounding
pans. By using more speakers in the system, the same sound levels may
be attained with less burden placed on any individual speaker.
• Stereo Mode – Two-channel mode with no surround sound.
Surround modes are selected using your receiver or processor. The
availability of multichannel surround sound depends on the capabilities of
your receiver/processor; consult its owner’s manual for more information.
The surround back speakers may also be used with specialized
surround modes that are designed for use with 7.1-channel systems,
such as Dolby Digital EX, DTS-ES® (Discrete and Matrix) and Logic 7
(7.1 modes). However, the surround back speakers are optional.
Many people expect the surround speakers to play as loudly as the
front speakers. Although all of the speakers in the system will be
calibrated to sound equally loud at the listening position, most sound
tracks use the surround speaker for ambient effects only, and they
program their materials to steer very little sound to these speakers.
• Subwoofer – A subwoofer is a special-purpose speaker designed
to play only the lowest frequencies (bass). It is used to augment the
smaller, limited-range satellite speakers used for the other channels.
In addition, many digital-format programs, such as movies recorded
16
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
There are different types of audio and video connections used to
connect the DVD 38 to your receiver or processor and video display.
To make it easier to keep them all straight, the Consumer Electronics
Association (CEA®) has established a color-coding standard. Table 1
may be helpful to you as a reference while you set up your system.
should not connect coaxial digital audio outputs to analog inputs or
vice versa. See Figure 1.
Coaxial digital
Coaxial
audio cable
Figure 1 – Coaxial Digital Audio
Table 1 – Connection Color Guide
Optical digital audio connectors are normally covered by a shutter to
protect them from dust. The shutter opens as the cable is inserted.
See Figure 2.
Audio Connections
Left
Right
Front (FL/FR)
Center (C)
Optical
Surround (SL/SR)
Subwoofer (SUB)
Optical digital
audio cable
Figure 2 – Optical Digital Audio
Digital Audio Connections
Coaxial
Due to the nature of digital signals as binary bits, they aren’t subject
to signal degradation the way analog signals are. Therefore, the quality
of coaxial and optical digital audio connections should be the same,
although it is important to limit the length of the cable. Whichever type of
connection you choose, Harman Kardon recommends that you always
select the highest quality cables available within your budget.
Optical
Input
Pb
Output
Pr
Video Connections
Component
Y
Composite
S-Video
HDMI™ Connections
HDMI
Analog Audio
Types of Connections
Analog connections require two cables, one for the left channel (white)
and one for the right channel (red). See Figure 3. These two cables are
often attached to each other for most of their length. Most devices that
have digital audio jacks also have analog audio jacks. We recommend
that you always connect the DVD 38’s 2-Channel Analog Audio Outputs
to your receiver/processor, or to your TV if you are not using a receiver.
There are four reasons to use analog audio connections, even if you are
using one of the digital audio connections:
This section will briefly review different types of cables and connections
that you may use to set up your system.
Audio and video signals originate in what are known as “source
devices,” including a DVD/CD player such as the DVD 38.
Separate connections are required for the audio and video portions of
the signal unless an HDMI connection is used (see below). The types of
connections used depend upon what’s available on your receiver, and
for video signals, the capabilities of your video display.
1. To make recordings. Most DVDs are protected from digital copying
and only analog copies are permitted. Please make sure to comply
with all copyright laws when making recordings for personal use.
Audio Connections
There are two formats for audio connections: digital and analog. Digital
audio signals are required for listening to sources encoded with digital
surround modes, such as Dolby Digital and DTS. There are two types
of digital audio connections commonly used: coaxial and optical. Either
type of digital audio connection may be used, but never both simultane-
ously. However, it’s okay to make both analog and digital audio connec-
tions at the same time to the same source.
2. In a multiroom system. Many receivers and processors require
sources used in multiroom systems to output analog audio signals.
3. When connecting the DVD 38 directly to a TV. The TV may not have
digital audio inputs.
4. When playing high-resolution 96kHz PCM audio discs. If your receiver
is not capable of processing 96kHz audio, you may need to use the
analog audio connection.
NOTE: The DVD 38 outputs digital audio signals through the
HDMI connection. If your receiver/processor or video display
is capable of processing the audio portion of the HDMI signal,
then you will not need to make a separate digital audio connec-
tion. However, as explained in the Analog Audio section below,
you may still need to make the analog audio connections. If
your receiver/processor is only capable of switching HDMI
signals, use HDMI for your video connection only and connect
either the DVD 38’s coaxial or optical digital audio output to
the corresponding input on your receiver.
NOTE: The DVD 38 is capable of downmixing multichannel
materials and outputting a two-channel downmix. However,
make sure to adjust the Bass Management setting in the Audio
Setup menu to Stereo.
L
Analog audio
cable (RCA)
R
Figure 3 – Analog Audio
Multichannel analog connections are used with high-resolution DVD-
Audio discs, where the copy-protected digital content is decoded inside
the DVD 38. These connections are required for playing DVD-Audio
discs, unless the disc also carries two-channel PCM and 5.1-channel
Digital Audio
Coaxial digital audio jacks are usually color-coded in orange. Although
they look similar to analog jacks, they should not be confused, and you
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
Dolby Digital or DTS soundtracks for use with receivers/processors that
are not equipped with 5.1-channel analog inputs. Check the disc’s jack-
et for more information on alternate audio tracks. See Figure 4.
composite video cable into an analog or coaxial digital audio jack, or
vice versa. Both the chrominance (color) and luminance (intensity)
components of the video signal are transmitted using a single cable.
See Figure 6.
Front Surround Center
Composite
Multichannel
analog audio
cable (RCA)
video cable
Figure 6 – Composite Video
Subwoofer
S-video, or “separate” video, transmits the chrominance and luminance
components using separate wires contained within a single cable. The
plug on an S-video cable contains four metal pins, plus a plastic guide
pin. Be careful to line up the plug correctly when you insert it into the
jack on the receiver, source or video display. See Figure 7.
Figure 4 – Multichannel Analog Audio
NOTE: In order to enjoy the full benefit of lossless multichannel
recordings, make sure the Bass Management setting in the AUDIO
SETUP menu is set to On or Bypass, depending on the bass
management capabilities of your receiver/processor. When the
Stereo setting is selected, the center and surround channel infor-
mation will be combined with the left and right channels, and will
only be heard through the front channels. This setting may also be
accessed by pressing the Audio Mode Button on the remote.
S-video cable
Figure 7 – S-Video
Component video separates the video signal into three components –
one luminance (“Y”) and two sub-sampled color signals (“Pb” and “Pr”) –
that are transmitted using three separate cables. The “Y” cable is
color-coded green, the “Pb” cable is colored blue and the “Pr” cable
is colored red. See Figure 8.
Video Connections
As mentioned above, the video signal is often transmitted separately
from the audio signal. Even when the HDMI connection described below
is used, sometimes the receiver is not capable of accessing the audio
portion of the HDMI signal, and a separate audio connection is required.
Component
video cable
Figure 8 – Component Video
Digital Video
Do not confuse component video connections with composite video
(described above). Although the plugs and jacks may look similar, they
are not compatible and cross-connecting them will result in no picture
or a very distorted picture. Remember that component video uses three
connections, colored green, blue and red, while composite video uses
a single connection, which is often color-coded yellow.
The DVD 38 is equipped with an HDMI (High-Definition Multimedia
Interface) output. HDMI is capable of carrying digital audio and video
information using a single cable, delivering high-quality picture and
sound.
The DVD 38 is capable of outputting up to 720p or 1080i video and
2-channel PCM or up to 5.1-channel Dolby Digital or DTS audio
through its HDMI connection. The DVD 38 is in compliance with HDCP
(High-Definition Copy Protection) and the video display must also be
HDCP-compliant to be used with the DVD 38’s HDMI output.
If your video display is capable of handling progressive-scan signals
(480p or better), then connect the DVD 38’s Component Video Outputs
to the input jacks on your video display marked “HD Component”. Make
sure to configure your display for use with 480p video signals. Set the
Scan Type setting in the DVD 38’s Video Setup menu to Progressive;
this setting may also be accessed by pressing the Scan Type Button on
the remote (marked P/I).
The DVD 38 is Simplay HD-verified for compatibility
via the HDMI connection with other Simplay HD-verified products.
The physical HDMI connection is simple. The connector is shaped for
easy plug-in (see Figure 5). If your video display has a DVI input, you
may use an HDMI-to-DVI adapter (not included) to connect it to the
HDMI Output.
NOTES:
• The DVD 38’s component and S-video outputs are not avail-
able simultaneously. Adjust the Video Output setting in the
VIDEO SETUP menu for the desired output. You may need to
temporarily connect the DVD 38’s Composite Video Output to
your video display in order to view the menu.
Figure 5 – HDMI Connection
• For simplified operation, connect one of the DVD 38’s video
outputs to your receiver or processor, and use the receiver/
processor as a switching device for all of your sources, con-
necting only the receiver/processor to your video display.
However, if your receiver is not capable of switching HDMI
signals, connect the DVD 38’s HDMI Output directly to an
HDMI-capable video display for superior picture quality.
Analog Video
There are three types of analog video connections: composite video,
S-video and component video.
Composite video is the basic connection most commonly available.
The jack is usually color-coded yellow, and looks like an analog audio
jack, although it is important never to confuse the two. Do not plug a
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
• If you are using the DVD 38 with a multiroom receiver/
processor that is capable of distributing video, connect the
DVD 38’s Composite Video Output to the receiver in addition
to the HDMI, Component Video or S-Video Output.
If it’s available on your video display, HDMI is recommended as the
best-quality connection, followed in preference by component video,
S-video and then composite video. Except as indicated above for use
in a multiroom system, do not connect more than one video output from
the DVD 38 to another device.
Remote IR Input and Output
The DVD 38 is equipped with an infrared input and output to facilitate
use of your system with a remote control in a variety of situations.
When the DVD 38 is placed in such a way that aiming the remote at the
front-panel IR sensor is difficult, such as inside a cabinet or facing away
from the listener, you may connect an external IR receiver, such as the
optional Harman Kardon HE 1000, to the Remote IR Input jack.
If your receiver or any of your other components are equipped with a
compatible remote IR input, you may use the included 1/8" mini-plug
interconnect cable to connect the Remote IR Output to the device’s
remote IR input, which will pass any applicable remote signals transmitted
through the DVD 38 to the other device. This enables you to control
your devices even when the DVD 38 itself is controlled via an external
IR receiver.
To control more than one device using the Remote IR Output, connect
all devices in “daisy chain” fashion, with the receiver’s remote IR output
connected to the DVD 38’s Remote IR input, then the DVD 38’s Remote
IR Output connected to the next device’s remote IR input, that device’s
remote IR output connected to the next device’s remote IR input, and
so forth.
NOTE: Not all remote controllable devices are equipped with
compatible IR inputs and outputs. Check with the manufacturer
of the source device for more information on the type of IR
signal expected. The DVD 38 will output a “stripped carrier”
IR signal.
19
19
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
You are now ready to connect the DVD 38 to your system. Before begin-
ning, make sure that all components, including the DVD 38, are turned
completely off and their power cords are unplugged. Don’t plug any
of the power cords back in until you have finished making all
of your connections.
Figure 11 – 2-Channel Analog Audio Outputs
Many components in a home theater system, such as a receiver or
power amplifier, generate a great deal of heat that can interfere with the
operation of the DVD 38. Therefore, it is best to place the DVD 38 on
its own shelf instead of stacking it directly on top of another component.
It is also a good idea to check the finish of your shelf. Some wood or
other finishes can be affected over time by the DVD 38’s rubber feet.
NOTE: The DVD 38 is capable of downmixing 5.1-channel
materials to the two-channel format, but it is necessary to adjust
the Bass Management setting in the AUDIO SETUP menu to
Stereo. You may also access this setting by pressing the Audio
Mode Button on the remote. If you leave the Bass Management
setting at On or Bypass, the DVD 38 will only output content
specific to the front left and right channels through the
2-Channel Analog Audio Outputs, losing the center and surround
channel information.
Step One – Connect the DVD 38 to Other
Components
Select one of the following two sections, depending on whether you are
connecting the DVD 38 directly to a television or video display, or if you
are using an audio/video receiver or processor (this manual will use the
term “receiver” to refer to either a receiver or a processor) that incorpo-
rates the DVD 38 as part of a home theater system.
After you have connected the DVD 38 to your television, skip to
Step Two for more information.
Connecting the DVD 38 to an Audio/Video Receiver
Connecting the DVD 38 Directly to a Television
One of the major advantages of the DVD format is its ability to use a
variety of digital audio formats for the ultimate in sonic performance.
In addition, the DVD 38 is capable of playing DVD-Audio discs, which
contain high-resolution multichannel audio materials. In order to benefit
from these audio formats, we strongly recommend that you connect the
DVD 38 to a 5.1-, 6.1- or 7.1-channel audio/video receiver with the
ability to decode digital audio such as Dolby Digital and DTS, and with
5.1-channel “direct” analog audio inputs. Harman Kardon AVR Series
receivers are compatible with the DVD 38.
If your television is HDMI-capable and HDCP-compliant, then only one
cable connection is required, and it will carry both audio and video
signals. Use the included HDMI cable to connect the DVD 38’s HDMI
output to your television’s HDMI input. See Figure 9. If your television
has a DVI input rather than an HDMI input, purchase an HDMI-to-DVI
cable or adapter.
The DVD 38 is Simplay HD™-verified for compatibility
via the HDMI connection with other Simplay HD-verified products.
The DVD 38 may also be used with an analog A/V receiver by connect-
ing the 2-Channel Analog Audio Outputs to any one of the receiver’s
inputs (in addition to a video connection).
If your receiver is HDMI-capable, connect the DVD 38’s HDMI Output
to one of the receiver’s HDMI inputs. See Figure 9. If the receiver is
equipped with a DVI port, purchase an HDMI-to-DVI cable or adapter.
Figure 9 – HDMI Output
NOTE: When using the HDMI connection, turn on the television
or video display before the DVD 38.
The DVD 38 is Simplay HD™-verified for compatibility
via the HDMI connection with other Simplay HD-verified products.
If your video display does not have an HDMI input, then separate audio
and video connections are required. Select one of these types of video
connections, in order of preference: component video, S-video,
composite video. See Figure 10.
Figure 9 (repeated) – HDMI Output
Check your receiver’s owner’s manual to determine how it handles
HDMI signals. It may simply switch the signal, it may process the audio
portion of the signal but not the video portion, or it may be capable
of processing both the audio and video portions of the signal. If the
receiver only switches the signal, but is not capable of accessing and
processing the audio or video data, then a separate audio connection
is required, as explained below.
Figure 10 – Component, S- and Composite Video Outputs
Other than HDMI, most video displays are not equipped with coaxial or
optical digital audio inputs. If your display is, then it would be preferable
to connect one of the DVD 38’s digital audio outputs to the correspon-
ding input on your display. However, most likely you will use the
2-Channel Analog Audio Outputs. See Figure 11.
If the receiver is not HDMI-capable, then separate audio and video
connections are required. Select one of these types of video connec-
tions, in order of preference: component video, S-video, composite
video. See Figure 10.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Figure 10 (repeated) – Component, S- and Composite Video Outputs
Figure 11 (repeated) – 2-Channel Analog Audio Outputs
If your receiver is equipped with digital audio inputs, then select either a
coaxial or optical digital audio input, and connect it to the corresponding
output on the DVD 38. See Figure 12. This step also applies to a
receiver that is only capable of HDMI switching and cannot process
the audio portion of the HDMI signal. If your HDMI-capable receiver
processes the HDMI audio, then do not make another digital audio
connection.
Even if you connected one of the DVD 38’s digital audio outputs to
your receiver, you may wish to connect the 2-Channel Analog Audio
Outputs to your TV (if it isn’t HDMI-capable) so that you may watch a
DVD without turning on your complete home theater system. If you
make this connection, remember to also connect one of the DVD 38’s
video outputs directly to the TV.
Step Two – Plug In AC Power
Having made all of your wiring connections, it is now time to power
up the DVD 38. Plug the AC Power cord into a working, unswitched
AC outlet. See Figure 14.
Figure 12 – Coaxial and Optical Digital Audio Outputs
If you wish to enjoy DVD-Audio discs in their native lossless format,
connect the DVD 38’s 6-Channel Analog Audio Outputs to the corre-
sponding 6-channel analog audio inputs on the receiver. This connection
is necessary because the digital content is copy-protected and
decoded by the DVD 38, with only the analog audio output available.
See Figure 13.
Figure 14 – AC Input for Power Cord
Step Three – Insert Batteries in Remote
The DVD 38 remote control uses two AAA batteries (included).
To remove the battery cover located on the back of the remote, firmly
press the ridged area and slide the cover towards the bottom of
the remote.
Insert the batteries as shown in Figure 15, making sure to observe
the correct polarity.
Figure 13 – 6-Channel Analog Audio Outputs
NOTE: When using the 6-Channel Analog Audio Outputs,
remember to adjust the Bass Management setting in the AUDIO
SETUP menu to On if the inputs on your receiver are “direct”,
meaning that the receiver does not perform any bass manage-
ment on the signal; or to Bypass if the receiver does perform
bass management on the 6-channel inputs, which may be
indicated by calling them 6-channel DVD-Audio inputs. Consult
your receiver’s owner’s manual for more information.
Figure 15 – Remote Battery Compartment
As explained in the Connections section, there may be several reasons
for using the DVD 38’s Analog Audio Outputs in addition to the Digital
Audio Outputs. If you wish to make recordings, to use the DVD 38 as
an audio source for a multiroom system, to play 96kHz discs when your
receiver is not capable of processing 96kHz audio, or if your receiver
is not equipped with digital audio inputs, then connect the DVD 38’s
2-Channel Analog Audio Outputs to any pair of analog audio inputs
on the receiver. See Figure 11.
When using the remote, remember to point the lens toward the front
panel of the DVD 38. Make sure no objects, such as furniture, are
blocking the remote’s path. Bright lights, fluorescent lights and plasma
video displays may interfere with the remote’s functioning. The remote
has a range of about 20 feet, depending on the lighting conditions.
It may be used at an angle of up to 30 degrees to either side of the
DVD 38.
If the remote seems to operate intermittently, make sure the batteries
have been inserted correctly, or replace all three batteries with fresh ones.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Step Four – Turn On the DVD 38
Plugging the DVD 38 into AC power places it in Standby mode, which
is indicated by the Power Indicator (surrounding the Standby/On Switch)
turning amber.
NOTE: When HDMI connections are used, turn on your
television or video display before turning on the receiver and
DVD 38.
There are several ways in which the DVD 38 may be turned on from
Standby mode.
a) Press the Standby/On Switch on the front panel or remote.
See Figure 16.
Figure 16 – Standby/On Switch
b) Press the Open/Close Button on the front panel or remote.
See Figure 17.
Figure 17 – Open/Close Button
Pressing the Open/Close Button will also open the disc drawer.
c) Press the Play Button on the front panel or remote. If a disc is
present, it will begin playing automatically. See Figure 18.
Figure 18 – Play Button
After customizing a few settings in the Initial Setup section, you
may soon enjoy the finest in home entertainment.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETUP
Before you begin enjoying your new DVD player, a few adjustments
should be made to configure it.
All of the DVD 38’s menu screens follow the same basic format.
The top line is the Main Menu line. It indicates whether the SYSTEM
SETUP or PLAYER INFORMATION menu is active.
Make sure that you have connected a video display to one of the video
monitor outputs. When you turn on your display and the DVD 38, you
should see the DVD 38’s splash screen. The DVD 38 will determine
whether a disc is loaded and, if so, begin play. If not, the splash screen
will remain.
The DVD 38 displays instructions at the bottom of the screen to guide
you in making your selections.
On the left side of the screen are navigation icons that may be used
to access the submenus or display screens. Use the Navigation Buttons
on the remote to highlight an icon, and press the Enter button to select
or deselect it. When the icon is selected, it will look like a button that
has been pressed in. When it is deselected, it looks like a button in the
out position.
IMPORTANT NOTE: The DVD 38 is not capable of outputting
both S-video and component video signals simultaneously. If
you have used either of these connections and have no picture,
the likely problem is that the DVD 38 is set to output only the
other type of video.
The Setup submenus are:
Temporarily connect the DVD 38’s Composite Video Output to
the corresponding input on your TV. Press the Setup Button to
• SYSTEM SETUP: Identified by a wrench icon and the word SYSTEM.
Used to establish the player’s general settings.
⁄
access the menu system, and then use the /¤ Navigation
Buttons to highlight the VIDEO SETUP submenu’s icon (with the
word “VIDEO” on it). Press the Enter Button, and then use the
• AUDIO SETUP: Identified by a speaker icon and the word AUDIO.
Used to establish the player’s audio output settings.
⁄
/¤ Navigation Buttons to navigate to the Video Output line.
• SPEAKER SETUP: Identified by a loudspeaker cabinet icon. When
the Bass Management line of the AUDIO SETUP submenu is set to
On, this submenu is used to establish the Bass Management settings
for the 6-Channel Analog Audio Outputs that are used when a
DVD-Audio disc is playing.
⁄
If it is set incorrectly, press the Enter Button and use the /¤
Navigation Buttons to scroll to the desired type of video output,
then press the Enter Button again to select it. When you turn off
the DVD 38 and disconnect the composite video cable, you
should be able to see a picture using the S-video or component
video connection as appropriate.
• VIDEO SETUP: Identified by a TV icon and the word VIDEO. Used to
establish the video formatting and configuration settings and to access
the video adjustments screen for the picture settings.
Using the On-Screen Menu System
The PLAYER INFORMATION menu appears automatically for audio-only
discs, JPEG discs and VCDs without playback control (PBC). For DVDs
and VCDs with PBC, press the Info Button (see Figure 19) to display it.
Unlike the Setup menus, many of the lines on the Player Information
menu screens are informational displays only that cannot be changed.
The Player Information screens are described in greater detail in the
Operation section. The submenus available are:
The DVD 38 uses two types of menu screens: Setup menus and Player
Information menus.
Press the Setup Menu button on the remote to display the SYSTEM
SETUP menu. See Figures 19 and 20.
• PLAYBACK INFO: Identified by an “i” icon. Displays the disc type
and name (if available on the disc), and contains settings to control
the playback mode.
• PROGRAM: Identified by an icon showing musical notes. Used to
program a playlist, which lets you play back selected CD tracks in
the order you choose. Playlists are only available for audio CDs.
Figure 19 – Setup, Info, Disc Menu
and Navigation Buttons
• DISC INFO: Identified by a disc icon. Displays detailed information
about the audio and video content on the current disc.
The main area of each setup menu’s screen contains the various
configuration settings, with the current setting displayed to the right.
Use the Navigation Buttons to highlight a setting. Press the Enter Button,
and a dropdown menu will appear that contains the available options
⁄
for that setting. Press the /¤ Navigation Buttons until the desired
option is highlighted, then press the Enter Button to select that option.
See Figure 21 for an example of a dropdown menu.
Figure 20 – System Setup Menu Screen
23
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETUP
Figure 22 – Languages Screen
Figure 21 – Settings Dropdown Menu
This procedure selects a preferred subtitle language, but it will only be
available when the disc being played contains that language. The list of
subtitles available on any given disc is always shown on the disc jacket,
usually at the bottom of the back cover. The subtitles may also be
switched on or off, or a new language selected during playback using
the Subtitle Button.
Press the Enter Button when the desired setting is highlighted, and use
the ⁄/¤ buttons to select another setting line.
Some settings call for numeric entries, such as the password for
the Parental Control setting. A set of underscore lines will be shown
(_ _ _ _). Use the Numeric Keys on the remote to enter the code,
and the DVD 38 will automatically proceed to the next setting line.
If you have selected a subtitle language and subtitles do not appear
on screen, press the Subtitle Button to display the Subtitle banner.
Each press of the Enter or Subtitle button will cycle through the subtitle
language options available on the disc. Use the ‹/› buttons to
navigate to the Done button, and press Enter to clear the banner
from the screen.
When you have made all desired adjustments to the current submenu,
use the Navigation buttons to highlight the icon for the next submenu,
and press the Enter Button to switch to that submenu.
When you have finished adjusting all settings, press the Setup button
to clear the menu from the display. See Figure 19.
If subtitles still do not appear, press the Disc Menu Button to make
sure that subtitling has been selected in the disc’s menu system.
See Figure 19.
Step One – System Setup
In this step you will configure some basic system settings using the
SYSTEM SETUP submenu. Press the Setup Button and the Enter Button
as explained above to access the settings in this submenu. Your screen
should look similar to the one shown in Figure 20.
NOTE: Due to the variations in how DVD discs are authored,
the subtitle languages displayed by the DVD 38 may not accu-
rately reflect the actual languages available on the disc. It is
recommended that subtitles be selected using the disc’s menu.
DISPLAY LANGUAGE: This setting selects the language that will be
used for the DVD 38’s OSD menus and other system messages.
The default is English, but you may select French, Spanish, German
or Italian.
PANEL TIME-OUT: This setting allows you to select the length of time
the Front-Panel Display remains lit during disc playback (as some people
find the front-panel display distracting while a movie is playing). You may
program the DVD 38 to refresh the front-panel display only when a
button is pressed on the remote or front panel, and to turn the display
off again after either five or 20 seconds. When the display is off, the
blue Power Indicator will remain lit to remind you that the unit is turned
on. When the Panel Time-Out setting is set to “Off,” the display remains
lit at all times. This feature is only in effect when a DVD or VCD is
playing. However, you may always press the Dimmer Button to dim
the front-panel display either by half or fully.
PREFERRED SUBTITLE LANGUAGE: This setting selects the language
used for the display of subtitles. The default setting is OFF, to play discs
without subtitles. To set the player so that subtitles will always play in a
specific language when they are available, select from the choices
shown.
If you do not find your preferred language in the options list, you may
select a preferred language by first pressing the ⁄/¤ Buttons so
that UNKNOWN or OTHER is highlighted in the drop down menu. Press
‹ ›
the Enter Button, and then use the ⁄/¤/ / Buttons to select a
STATUS BAR TIME-OUT: This setting selects the timeout interval for
the on-screen Status Bar that appears at the top of your video screen
when the Status Button is pressed while a disc is playing. During DVD
playback, the status bar shows the current title and chapter, playback
mode, the elapsed or remaining time in the current chapter or title,
a setting to adjust the time display, and a temperature bar for the
time display.
language from those shown on screen (see Figure 22). You may exit
the languages screen by navigating to the word RETURN at the bottom
of the screen and pressing the Enter Button to return to the SYSTEM
SETUP submenu.
You may program the status bar to remain on screen for either five or
20 seconds after the Status Button is pressed. When OFF is selected,
the timeout is disabled, and the status bar will remain on the screen until
the Status Button or Clear Button is pressed. We strongly recommend
programming the Status Bar to disappear on its own to avoid burning
its image into a plasma or CRT display.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
PARENTAL CONTROL: The DVD 38’s password system allows you to
restrict viewing of certain materials that may not be suitable for younger
members of the household by requiring the viewer to enter a password
to view those materials. The system is based on rating information
encoded in some DVDs that classifies materials into eight levels, roughly
corresponding to the Motion Picture Association of America (MPAA)
voluntary ratings system:
DISC RECOGNITION: When this setting is turned on, the Disc
Recognition feature allows you to stop a DVD-Video disc, remove it
from the player, play another disc, and then resume playback of the
original disc at a later time from the point at which you paused. When a
previously played disc is reinserted in the DVD 38, you will be presented
with an on-screen status message asking whether you wish to start
playback from the beginning of the disc or resume at the point where
you left off. Even when the setting is activated, to benefit from Disc
Recognition, you must press the Stop Button either once (Resume
mode) or twice (Stop mode), but not the Pause Button. The unit may be
turned off between discs. The DVD 38 can store the information for up
to five DVDs at a time.
Level 1 G: Corresponds to the MPAA’s “G” (General Audiences) rating,
and is considered suitable for all viewers.
Level 2: Intermediate level between the “PG” and “G” ratings.
Level 3 PG: Corresponds to the MPAA’s “PG” (Parental Guidance) rating.
PBC SUPPORT: This setting controls the activation of PBC (Play Back
Control) Support for VCD discs. If you plan to play VCD discs, which are
a CD-ROM-based format that predates DVD, we recommend that the
setting be turned ON. However, with PBC enabled, the Repeat Track,
Repeat Disc and Random functions may not be available for VCDs.
Level 4 PG13: Corresponds to the MPAA’s “PG-13” (Parental
Guidance and 13 years old) rating.
Level 5: Intermediate level between the “R” and “PG-13” ratings.
Level 6 R: Corresponds to the MPAA’s “R” (Restricted) rating.
Level 7 NC17: Corresponds to the MPAA’s “NC-17” (17 years and
older) rating.
SCREEN SAVER: The DVD 38 offers a Screen Saver option to protect
your TV or video display from damage that may occur if the player is left
turned on with the same still image for a period of time, as there is a
possibility that the image may be “burned” into some display devices.
This is particularly important for plasma displays and some CRT devices.
Set Screen Saver to ON so that the DVD 38 will run the screen saver
when no action has been detected for either one or five minutes. Press
a desired command key on the front panel or remote to “wake” the
DVD 38 and resume normal operation.
Level 8 Adult: All DVDs, including adult materials, can be played.
Off: Any DVD may be viewed without entering the password.
The DVD 38 is shipped from the factory with the parental control system
unlocked (no password is required to view any DVD), and with the
password set to the four-digit code “1234.” To activate the system,
highlight the Parental Control Setting on the SYSTEM SETUP submenu,
and press the Enter Button. Select On from the dropdown menu and the
Password Screen will appear (see Figure 23). Use the Numeric Keys to
enter the password code.
IMPORTANT NOTE: If the screen cursor is left on one of the
navigation icons on the left side of the screen, the screen saver
will not be activated. Moreover, some discs, such as DVD-Audio
discs and JPEG discs, can leave a still image displayed indefi-
nitely. Use caution in these situations to avoid causing burn-in
on your video display.
SHOW ANGLE ICON: Some DVDs are programmed with multiple-angle
capability, allowing you to view the same scene from a different camera
angle. Normally, the angle icon will be displayed on screen during those
sections of the disc to inform you that you may press the Angle Button
to change to a different view. If you find the appearance of the icon
on-screen distracting, select the Show Angle Icon setting in the SYSTEM
SETUP submenu, and set it to OFF. The front-panel Angle indicator will
remain lit for the duration of the sequence containing multiple camera
angles, regardless of the Show Angle Icon setting.
Figure 23 – Password Screen
If you have entered the password correctly, the Rating line will be
highlighted. Press the Enter Button to display the ratings dropdown
menu. Select a new rating using the /¤ Navigation Buttons and
⁄
the Enter Button.
CLOSED CAPTION: This setting enables viewing of closed caption
messages, if they have been encoded in the video material. Closed
captions – text displays of the program’s dialogue which are normally
hidden from view – are broadcast for the hearing-impaired or others.
Select the ON setting to activate the DVD 38’s closed captioning
decoder so that these messages may be viewed.
The first time you use the DVD 38, it is recommended that you scroll
to the Change Password setting and press the Enter Button to enter a
new password. Use the Numeric Keys to enter your new password once
at the New Password prompt, and a second time at the Confirm
Password prompt. The DVD 38 will return to the screen shown in Figure
23, and you may then change the Ratings Setting. After you press the
Enter Button and return to the SYSTEM SETUP submenu, the new
password will take effect.
Step Two – Audio Setup
In this step you may make adjustments to the audio settings using the
Audio Setup submenu.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETUP
Use the ‹/› Buttons to move the cursor to the submenu icons on the
left side of the screen, and then use the ⁄/¤ buttons to highlight the
Audio Setup icon. See Figure 24. Press the Enter Button, and then use
the Navigation Buttons to move the cursor to the settings on the AUDIO
SETUP submenu.
greater than 48kHz, select the 96kHz setting. If your receiver is not
capable of resolving these signals, or if you aren’t sure of your receiver’s
capabilities, select the 48kHz setting. At the 48kHz setting high-resolu-
tion materials will be downsampled to 48kHz. If you select the 96kHz
setting when your receiver is not capable of processing high-resolution
signals, you will not hear any audio when these materials are played.
NOTE: Due to copyright restrictions, the DVD 38 will not output
an uncompressed signal in the PCM format from a disc recorded
with 96kHz/24-bit resolution, such as some DTS audio CDs.
If the Digital Output setting in the Audio Setup submenu is set
to PCM, and the PCM Limit setting is set to 96kHz, no audio
will be outputted, and the message CGMS MUTE will appear in
the Main Information Display. “CGMS” stands for “Copy General
Management System.” Should this message appear, change
the PCM Limit setting to 48kHz to hear the audio at a lower
resolution.
Figure 24 – Audio Setup Submenu
PREFERRED AUDIO LANGUAGE: This setting is used to select the
default language that will be used for program playback. The factory
default setting is English, but you may choose French, Spanish, German
or Italian by making a selection from the dropdown menu as explained
in the Using the On-Screen Menus section. To select a language other
than those shown, select OTHER from the dropdown menu and press
the Enter Button. The Languages Screen (see Figure 22) will appear.
Navigate to the desired language and press the Enter Button to select
it, or navigate to RETURN at the bottom of the screen and press the
Enter Button to return to the AUDIO SETUP submenu.
DYNAMIC RANGE: This setting allows you to take advantage of the
Night-mode encoding present on some Dolby Digital recordings to
reduce the volume of louder passages while maintaining intelligibility of
quieter passages. This allows you to listen to programs at a level that
allows the full impact of a soundtrack to be heard at a volume that is
lower than you might otherwise use to avoid disturbing others. The
DVD 38 accomplishes this by compressing the audio to a greater or
lesser degree, depending on which setting you choose. Three options
are available:
This procedure selects a preferred audio program language, but it will
only be available when the disc being played contains that language.
The list of languages available on any given disc is always shown on the
disc jacket, usually at the bottom of the back cover. The audio playback
language may also be changed during playback using the Audio Select
Button, but any changes made will only be effective during playback of
that disc.
• MAXIMUM: Does not make any changes to the original signal,
and should be used when the volume setting in the listening room
may be as loud as you desire.
• MEDIUM: Applies a moderate amount of compression so that louder
passages are a little bit quieter.
• MINIMUM: Applies more compression so that louder passages are
much softer.
NOTE: The Audio Select Button is also used to change the
disc’s audio output format, e.g., Dolby Digital 5.1 versus
Dolby Digital 2.0.
NOTE: If your receiver or processor also allows you to program
the dynamic range setting, sometimes called “Night Mode,” you
do not need to adjust this setting on the DVD 38 and you
should leave it at MAXIMUM.
DIGITAL OUTPUT: This setting selects the digital audio data stream
that is routed to the Optical or Coaxial Digital Output. Two choices are
available:
DELAY UNIT: This setting selects the unit of distance used for calculat-
ing delay times when the AUDIO ADJUSTMENTS submenu is activated
using the Bass Management setting described below. The default unit is
feet, but you may select meters.
• Bitstream: This is the default setting. The DVD 38 will output the
Dolby Digital or DTS signal selected using the disc’s menu or using
the Audio Select Button. This setting should be used when your
receiver or processor is capable of decoding signals in the Dolby
Digital or DTS format.
BASS MANAGEMENT: This setting activates the AUDIO ADJUSTMENTS
menu’s bass management settings, to optimize playback of DVD-Audio
discs through the 6-Channel Analog Audio Outputs, or to downmix the
signal to two channels. This setting may also be adjusted by pressing
the Audio Mode Button on the remote repeatedly until the desired
setting is selected. Three settings are available:
• PCM: At this setting the DVD 38 outputs a standard PCM signal for
decoding by receivers or processors that are not capable of decoding
a Dolby Digital or DTS bitstream. This setting enables 2-channel audio
playback or matrix decoding where available.
• On: If your receiver or processor is equipped with “direct” 6-channel
inputs and the receiver is not capable of performing bass management
on these inputs, then change this setting to On, and proceed to the
AUDIO ADJUSTMENTS menu to program the bass management
settings.
NOTE: Any changes made to the Digital Output setting during
playback will not take effect until after play has been stopped
and restarted.
PCM LIMIT: This setting affects playback of high-resolution (96kHz or
greater) audio materials. If your receiver is capable of handling signals
26
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETUP
• Bypass: This is the default setting. If your receiver or processor is
equipped with 6-channel inputs and is capable of adjusting the bass
management settings (speaker size, output levels and delay times)
for its 6-channel analog inputs (sometimes called the 6-channel
DVD-Audio inputs during source selection), then we recommend
you leave this setting at the default Bypass, and adjust the bass
management settings on your receiver.
If your receiver does not have 6-channel analog inputs, make sure to
select Stereo for the Bass Management setting in the AUDIO SETUP
menu. Then connect the Analog Audio Outputs to any
2-channel analog inputs on your receiver.
Press the Setup Button to activate the Setup menu; then use the
⁄ ¤
/
Navigation Buttons until the AUDIO ADJUSTMENTS submenu
is highlighted, and press the Enter Button. See Figure 25.
• Stereo: If your receiver or processor is not equipped with 6-channel
inputs at all, or if you wish to use the DVD 38 as the source for a
multiroom system, to connect it directly to your TV or for recording,
then change this setting to Stereo, which will send a downmixed 2-
channel signal to the Analog Audio Outputs, for use with any 2-chan-
nel analog input on your receiver. You may then select an analog sur-
round mode available on your receiver.
NOTE: The 2-channel downmix (Stereo mode) and the
5.1-channel presentation of multichannel audio discs (Bypass or
Bass Management On modes) are not available simultaneously.
Figure 25 – Audio Adjustments Submenu
The following adjustments are available on the AUDIO ADJUSTMENTS
menu for each speaker position. Use the Navigation Buttons to select
the settings for each speaker. Press the Enter Button to display a drop-
⁄ ¤
With bass management on or in Bypass mode, the same front
left and right channel information will be available at both the 2-
Channel and 6-Channel left and right Analog Audio Outputs. No
center or surround information will be present in the signal out-
put at the 2-channel Analog Audio Outputs.
down menu with the selections available for the setting. Use the
/
Navigation Buttons to highlight the appropriate setting, and then press
the Enter Button to select it.
In Stereo mode, the downmixed 2-channel signal will be
available at both the 2-Channel and 6-Channel Analog Audio
Outputs, with no center or surround channel information
available at the 6-Channel Analog Audio Outputs.
You will notice that the adjustments for speaker size and distance (used
to calculate delay times) are set in tandem for the front left and right
speaker pair, and for the surround left and right speaker pair. Changing
the settings for either speaker in these pairs also affects that setting for
the other speaker in that pair. For this reason, it is important to select the
same brand and model for both speakers in each pair, and also to place
them at about the same distance from the listening position.
Step Three – Audio Adjustments
This menu allows you to adjust bass management settings that control
the audio output of the 6-Channel Audio Outputs for speaker size,
output level and delay times. The proper adjustment of these settings
is key to optimal reproduction of DVD-Audio discs, when the DVD 38 is
used with a receiver or processor that does not have audio adjustment
capabilities for the direct inputs. These settings are only effective when
the Bass Management line of the AUDIO SETUP submenu is set to On.
Before proceeding with the DVD 38’s audio setup adjustments, we
recommend that you first use the menu system in your receiver to
ascertain the settings already established for “Speaker Size,” “Output
Level” and “Delay Time” (may be set as a distance). Record these
settings in Table A3 in the appendix to refer to during the configuration
process, or follow these steps to obtain the information:
IMPORTANT NOTE: In order to avoid audio problems, when
the DVD 38 is connected to a receiver that does have the
capability to adjust bass management parameters for its
multichannel inputs, it is preferable to use the receiver for
these adjustments. In that case, remember to set the Bass
Management setting in the AUDIO SETUP menu to Bypass.
If you make the adjustments using the DVD 38's settings, it is
important that the receiver's settings for the multichannel direct
inputs be disabled, or set to “Large” for the speaker sizes and
“0” for the level adjustments and delay times, unless these
settings are also used for the receiver’s other source inputs, in
which case they should be left the way you set them when you
configured your receiver. If you have any questions about the
capabilities of your receiver or processor, we recommend that
you consult its owner’s manual or the manufacturer’s Web site
for further information.
1. Consult the frequency response specification (usually found in the
owner’s manual) for each of your speakers. Make a note of the
lowest frequency each speaker is capable of handling. For example,
if your speaker has a frequency response of 80Hz – 20kHz, then
80Hz is the lowest frequency it is capable of handling.
For your subwoofer, the important figure is the highest frequency it is
capable of handling. For example, if the subwoofer has a frequency
response of 25Hz – 150Hz, then 150Hz is the highest frequency
it can handle. Some subwoofers allow you to adjust the frequency
crossover. Consult the subwoofer’s owner’s manual for instructions on
setting its crossover, and use the approximate number you selected.
2. Measure the distance from each speaker to the listening position.
This is used for setting the delay.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETUP
If you use the metric system, return to the AUDIO SETUP submenu and
change the Delay Unit setting from its default of FEET to METER.
To adjust the output levels, first insert a disc with test tones or content
you are familiar with, and that has a reasonably even level without many
dynamic changes.
NOTE: The DVD 38 is designed to accommodate speaker
placements of up to 15 feet from the listening position. If you
have placed your speakers further from the listening position,
move them closer. If that isn’t possible, measure the differences
in the distances from each speaker to the listening position, and
enter the delay settings so as to reflect these differences, even
though the actual distances will be incorrect.
If you are using an SPL meter with a disc containing test tones, adjust
the level of each channel so that the meter reads 75dB. If you don’t
have a meter or a test disc, adjust the levels until all channels sound
equally loud. Make sure not to use a surround sound-encoded disc for
this process, or the surround channels will be set too high.
Use the Navigation Buttons to highlight the level setting for the front left
channel. Press the Enter Button to display the available settings, which
⁄ ¤
Before you begin to make the audio adjustments, select test program
material, either a test DVD you have purchased, or a movie or music
selection you are familiar with. For best results, you may wish to also
purchase a sound-pressure level (SPL) meter to assist you in setting
the output levels correctly. If you use an SPL meter, set it to the
C-Weighting, Slow scale, and adjust the receiver’s volume control until
the meter measures 75dB. If you don’t have an SPL meter, you may
set the output levels “by ear”.
range from –6 dB to +6dB, and use the
/
Buttons to scroll
through them until you are satisfied with the level setting for that channel.
Press the Enter button to select the setting, and use the Navigation
Buttons to select the next channel. Repeat the procedure to enter the
output level offset, if needed, that brings all of the channels to the same
output volume. You may need to repeat this procedure more than once
to accurately set the levels.
SPEAKER SIZE: Speaker size is part of the bass management system
which determines which frequencies are sent to the specific speaker
position, and which are sent to the subwoofer. The designation of “size”
does not refer to the speaker’s physical size, but rather to the lowest
frequency a speaker can handle. For this purpose, “full-range” speakers
are considered “large,” while those not capable of reproduction below
100Hz are considered “small.” In general, if you are using a packaged
speaker system with smaller satellite type speakers and a subwoofer,
you should select Small for all five speakers. Large should only be
selected if you are certain that your speakers are capable of handling
extreme low-frequency sounds.
For the subwoofer, the settings are slightly different. Select On when
a subwoofer is connected, or Off if one is not used.
The second setting for the subwoofer is the crossover. This determines
which sounds will be sent to the subwoofer, and which to the main
speakers when Small is selected as the speaker size for any of the
speakers. Select the frequency from those shown that is closest to the
lowest frequency your main (left/center/right/surround left/surround right)
speakers are able to reproduce. The output level should be set the
same way as for the other speakers.
Step Four – Video Setup
DELAY SETTINGS: The delay settings indicate the distance from each
speaker to the listening position. Although ideally you placed all of your
speakers in a circle equidistant from the listening position, we recognize
that it isn’t always practical to do so. This setting enables the DVD 38 to
delay the signal from some speakers by up to 15 mS to compensate.
In this step you may make a few adjustments to insure that the video
signal is output in a way that is compatible with your video display.
Use the ‹/› Buttons to move the cursor to the submenu icons on the
left side of the screen, and then use the ⁄/¤ buttons to highlight the
Video Setup icon. See Figure 26. Press the Enter Button, and then use
the Navigation Buttons to move the cursor to the settings on the Video
Setup submenu.
Use the Navigation buttons to highlight the distance for each speaker,
⁄ ¤
and press the Enter button to change it. Use the
scroll through the available settings.
/
Buttons to
NOTE: There is no delay setting for the subwoofer. Low-
frequency sound waves by their nature are not noticeably
affected by the distances in a typical listening room.
OUTPUT LEVEL SETTINGS: Output level adjustment is a key part of
the configuration process for any surround sound system. The goal is to
set the output levels so that all channels sound equally loud at the listening
position. This is important because movie directors adjust the loudness
of each channel in the recording to produce a desired sound presentation.
Usually the director reduces the loudness, or even the presence, of
information in the surround channels so as not to distract the viewer
from the main action taking place on screen. If the test tones on your
test disc sound as loud in the rear speakers as they do coming from
the other speakers, the DVD 38 is performing correctly.
Figure 26 – Video Setup Submenu
ASPECT RATIO: This setting selects the aspect ratio of video program-
ming. Your choice should be made according to the shape of your video
display and your personal preferences. Three choices are available:
• 16:9: If you have a widescreen (16:9) display, or a display that has
a widescreen mode, choose this setting. The DVD 38 will adjust the
output for widescreen movies so that they fill the entire screen in the
proper aspect ratio. However, a disc recorded in the 4:3 aspect ratio
In many cases the factory default setting of 0dB should accomplish that.
However, in some cases the specifics of your listening room may require
some adjustments.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETUP
will appear as a boxed image in the center, with black or gray bars on
the left and right side of the screen. If the widescreen option is chosen
and a widescreen movie is played on a conventional 4:3 aspect ratio
set, the image will be distorted due to vertical compression.
indicates the highest video resolution it is capable of handling, and the
DVD 38 automatically sets the video output to match it. That resolution
is displayed here (not in the front-panel display). If your program was
recorded at a low resolution, use this setting to manually select a lower
video output resolution. Changes made here remain active until the
DVD 38 or the display is turned off. When either is turned off, and then
on again, the DVD 38 will revert to the default setting transmitted by the
display. Make sure your video display is compatible with the DVD 38’s
HDMI output signal.
• 4:3 Letterbox: If you have a standard, 4:3 aspect ratio video display,
choose this setting to see the entire frame of the movie as it is
recorded on the disc without any image cutoff at the left and right
sides. While this allows widescreen movies to be shown in their entirety,
they will occupy a smaller portion of the screen and black “letterbox”
bars may appear at the top and bottom of the screen.
You may also access this setting by repeatedly pressing the HD Mode
Button on the remote.
VIDEO OUTPUT: This setting selects between the S-Video and
Component Video Outputs, which are not available simultaneously.
If you have connected one of these outputs to your video display and
the screen is blank, temporarily connect the Composite Video Output to
your TV in order to view the on-screen menus and change this setting.
Step Five – Video Adjustments
In this step you may adjust the brightness, sharpness and black level of
the video signal to compensate for differences between the DVD 38 and
other video sources. You may use either the DVD 38’s built-in color bar
test signal or a test disc as the standard for the adjustments. To ensure
that your system is properly optimized, we strongly recommend that you
adjust your video display using the display’s own controls before making
any changes to the DVD 38’s output. Once the display is properly
calibrated with all settings on the DVD 38 set to their midpoint, use the
controls on this menu to fine tune the DVD 38’s output, if necessary.
SCAN TYPE: This setting allows you to select between progressive and
interlaced scanning for the Component Video Outputs to maximize the
image resolution for the type of video display in use. The output at the
S-Video and Composite Video Outputs will always be standard-rate
video that is compatible with any television set or video display.
Two choices are available:
Due to the nature of these settings, the navigation is somewhat different
from the DVD 38’s other menus and controls. The banner is accessed
from the VIDEO SETUP submenu. Press the Setup Button to display
⁄ ¤
• Progressive: Select this option if you have a video display that is
compatible with input sources of 480p or greater. Displays labeled
as “HDTV Ready,” including virtually all large-screen LCD and plasma
displays, are compatible with progressive scan.
the Setup menu, and then press the
/
Navigation Buttons until
the VIDEO SETUP submenu icon is highlighted. Press the Enter Button
to access the VIDEO SETUP submenu, then scroll down to the Video
Adjustment line and press the Enter Button again. Select On to display
the VIDEO ADJUSTMENTS banner. The Setup screen will disappear
from view. See Figure 27.
• Interlaced: Select this option when you are using an older video
display that has Y/Pr/Pb component inputs, but which is not capable
of displaying high scan rate, or “HD,” signals.
NOTES:
• The Scan Type may only be changed when the Video Output
setting has been set to Component.
• If you have connected the DVD 38 to a video display that is
not capable of displaying progressive scan video using the
Component (Y/Pr/Pb) Video Outputs, and you have inadver-
tently changed the Scan Type to Progressive, reset the scan
type to Interlaced by pressing the Setup Button on the remote
to deactivate the Setup menu system. Then press the
Progressive Scan/Interlaced Button. The display will blink,
indicating that the scan type has been reset to interlaced
mode. Alternatively, as a last-resort measure, you may com-
pletely reset all of the DVD 38’s settings, including the scan
type, by exiting the on-screen menu system and pressing and
holding the Clear Button for five seconds. The display will
blink, and all settings will return to the factory defaults.
Figure 27 – Video Adjustments Banner
To change any of the video adjustments shown at the top of the screen,
use the Navigation Buttons to highlight the setting bar. Each press of
the › Button increases the setting, and each press of the ‹ Button
decreases it.
The default values for the Brightness and Edges settings are “0”, indicated
by the setting bar ending at the midpoint.
VIDEO ADJUSTMENT: Use this setting to access the Video Adjustments
banner by changing the setting from Off to On. See Step Five below for
more information on using the Video Adjustments banner to optimize
your picture settings.
When adjusting the Black Level setting, only two adjustments are available:
“0 to 100” provides a full black level setting, which is indicated by a
completely filled-in setting bar. This is the default setting that provides
the full dynamic range of black as it is presented on most DVDs.
HDMI SETTINGS: This setting displays the characteristics of the video
output signal. When the DVD 38 is connected to a video display using
the HDMI Output, the display sends information to the DVD 38 that
29
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETUP
“7.5 to 100” complies with NTSC standards for video with “setup”, and
may be more appropriate when you are only using the composite or
S-video output with a display that has limited video processing capability.
Contrast Adjustment
1. Adjust the contrast on your TV until you see a bright white bar in
the lower right corner of the screen and a deep-dark-black bar to
the left. The optimal contrast setting will depend on your preference
and the surrounding light in the TV room.
Changes to any of the settings may be made with a test disc or broad-
cast signal playing, or you may use the internal test screen by using the
Navigation Buttons to highlight the word OFF next to the TEST SCREEN
line. Press the Enter Button and the setting will change to ON. A special
combination test screen, including both color bars and gray scale along
with 100% black and white fields, will be displayed behind the Video
Adjustments banner. See Figure 28. If the Video Adjustments banner
disappears from view after a few seconds, press any button on the
remote to restore it so that you can make any necessary changes.
2. If the brightness of the white bar no longer increases when the
contrast is turned up or the borders of the white “harman/kardon”
letters on top bloom (overlight) into the black areas (drastically
decreasing the sharpness of the type), the contrast has been turned
up too much. Reduce the contrast until these effects disappear and
the video still looks realistic.
3. If you are watching TV with ambient daylight, adjust the contrast
so that a normal video picture has about the same look as the
surroundings in your room. That way the eye is relaxed when
watching the TV picture. This contrast setting may be reduced
when the surrounding light is dimmed, thereby usually improving
the sharpness of a video significantly.
4. The gray scale in the middle line needs to have the same clear
difference between each bar as before the contrast adjustment.
If not, go back to “Brightness Adjustment” and repeat Step 3 and
then “Contrast Adjustment,” making only minor adjustments each
time for optimization.
Figure 28 – Video Test Screen
With the test screen showing on your video display, the following
adjustments may be made:
Color Adjustment
1. When the brightness and contrast are set optimally, adjust the color
control to the level of your preference. Set the level so that the colors
look strong but still natural, not overdone. If the color level is too
high, depending on the TV, some of the bars will seem wider or the
color intensity will not increase when the control is turned up. Then
the color control must be reduced again. Ultimately, you also should
test the color intensity with a video – e.g., pictures of natural faces,
flowers, fruit and vegetables, and other common natural articles for
an optimal setting of the color intensity.
• The proper color intensity setting on your TV.
• Proper color adjustments using the color bars, which should be
(left to right) black, white, yellow, cyan (turquoise), green, magenta,
red, blue, black.
• The proper color transition, seen as sharp separation of the bars.
• The performance of the color circuits in your TV (with “Video”
signals); bar edges should show no vertical crawling dots.
With the gray scale and the black/white fields below the color bars, the
brightness and contrast of your screen can be adjusted.
2. Use the large white bar below the gray scale to tweak the warmth
of the picture. Every viewer has a preference as to how the glow of
the picture should be. Some prefer a colder picture, some a warmer
glow. The Tint function on your TV and the white bar can be used to
control this. Adjust the Tint to the level where you feel the white
color has the tone you prefer.
IMPORTANT NOTE: Video adjustments for all sources should
be made using the controls on your video display. Use the
DVD 38’s Video Adjustments Banner only if additional minor
corrections are needed when DVDs are played.
Brightness Adjustment
1. Turn down the color control on your TV until the color bars are
visible in black and white.
Sharpness Adjustment
Contrary to intuition, the picture will appear sharper and clearer with the
sharpness, or Edges, setting backed off from the maximum setting.
Reduce the sharpness setting on your television, and the Edges setting
on the DVD 38 video adjustments menu if necessary, to minimize the
appearance of any white lines between the bars in the gray scale portion
of the test screen.
2. Adjust the contrast to the lowest level where you still can see
all gray scale bars separately and clearly.
3. Adjust the brightness so that the bars in the gray scale are all
visible. The bar farthest to the left has to be as black as possible
rather than gray but the next gradation must clearly be distinct from
it. All the bars in the gray scale should be gradually and evenly
changing from black to white, left to right.
Convergence and Edge Focus
The crosshatch pattern that surrounds the test screen may be used to
evaluate edge focus and convergence in front- or rear-projection video
displays. However, the controls used to adjust these parameters are
30
30
Download from Www.Somanuals.com. All Manuals Search And Download.
INITIAL SETUP
often not user-accessible. In any event, these adjustments are extremely
complex, and require proper training and experience to avoid worsening
the situation. Therefore, it is recommended that if you are unable to
improve the picture using the available controls, contact the video
display manufacturer’s authorized service representative for assistance.
When you have finished making your adjustments, navigate to the word
Done and press the Enter Button to exit the Video Adjustments banner
and return to the VIDEO SETUP submenu.
When you have finished making all of the system, audio and video
adjustments, press the Setup Button or the Clear Button to clear the
screen. If a DVD is loaded, the splash screen will appear. If any other
type of disc is loaded, the Player Information menu will appear.
You are now ready to begin enjoying the finest in home entertainment
with your DVD 38 DVD player!
31
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Now that you have installed and configured your DVD 38, you are ready
to begin enjoying your home theater system.
Turning On the DVD 38
When you have plugged in the DVD 38, the Power Indicator next to the
power switch should light up in amber. This indicates that the DVD 38
is in Standby mode and is ready to be turned on. See Figure 16.
Figure 29 – How to Handle a Disc
• Do not stick paper or tape on the disc. If there is glue (or a similar
substance) on the disc, remove the glue completely before using
the disc.
• Do not expose the disc to direct sunlight or sources such as hot air
ducts, or leave it in a car parked in direct sunlight, as there can be
a considerable rise in temperature inside the car.
Figure 16 (repeated) – Standby/On Switch
There are several ways in which the DVD 38 may be turned on:
a) Press the Standby/On Switch. See Figure 16.
b) Press the Open/Close Button. See Figure 17.
c) Press the Play Button. See Figure 18.
• After playing, store the disc in its case.
• Do not write on the label side with a ball-point pen or other sharp
writing utensil.
• Be careful not to drop or bend the disc.
Disc Cleaning Precautions
• Before playing, clean the disc with a cleaning cloth. Wipe the disc
from the center out.
• Do not use solvents such as benzene, thinner, commercially available
cleaners or anti-static spray.
Figure 17 (repeated) – Open/Close Button
Disc Loading Precautions
• Do not load more than one disc on disc tray.
• Do not place a disc on the tray upside down.
• Do not try to close the disc tray when the disc is not positioned or
centered properly.
Figure 18 (repeated) – Play Button
Loading Discs
To turn the DVD 38 off, press either the Standby/On Switch on the front
panel, or press the Power Off Button on the remote. See Figure 16.
When the DVD 38 is unplugged, any settings you have programmed
will be preserved for up to four weeks.
To load discs in the DVD 38, first turn it on by pressing the Standby/On
Switch or the Open/Close Button on the front panel or the Power On
Button on the remote. The Power Indicator is amber when the unit is
connected to an AC power source, and it turns blue when the DVD 38
is turned on.
Although you may previously have owned a CD or DVD player, we
recommend you take a few minutes to learn the specifics of operating
the DVD 38. You also may want to take a moment now to review the
glossary terms in the back of the manual to familiarize yourself with
the terminology used to describe DVD players.
Next, if you have not already done so, press the Open/Close Button so
that the disc tray opens.
Hold the disc by the edge, and gently place it into the disc drawer, making
certain that the disc is properly seated in the tray’s insert. If the disc is
not correctly centered, you may damage both the disc and the player
when the drawer closes. When loading discs, please note the following:
Playback Basics
In some respects disc playback is the same for all types of discs.
We suggest you read through the basic instructions, and then read
the sections pertaining to the various disc types.
• The DVD 38 will play discs with the following logos as well as
most DVD-RW or DVD+RW discs and most WMA and JPEG discs,
including Kodak Picture CDs, but not Kodak Photo CDs. DO NOT
attempt to play another type of disc.
Disc Handling Precautions
• To keep the disc clean, handle the disc by its edge. Do not touch
the surface. See Figure 29.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
• The DVD 38 will only play discs that are coded for Region 1 or discs
that are open to being played in all regions (Region Code “0”). Discs
that contain a Region Code of 2, 3, 4, 5 or 6 (as noted by a number
inside a world map logo on the disc’s jacket) will not play.
• The DVD 38 will only display video in the NTSC format. The PAL
format is generally used in Europe and other regions of the world
outside North America, and some music or other DVDs are available
in PAL with a Region Code of “0”. The DVD 38 will automatically
detect the PAL format, and make the necessary conversions so that
the video may be displayed on an NTSC TV. PAL discs bearing a
Region Code other than “0” or “1” may not be played on the DVD 38.
Figure 30 – Player Information Screen (Audio CD)
• If the disc contains MP3, WMA or JPEG files, or if it is a VCD without
playback control, the Player Information display will appear. See Figure
31. To play one of these files, use the Navigation Buttons to select a
folder and press the Enter Button to open it. Use the Navigation
Buttons to select a file for playback, and press the Enter Button to
begin play.
• Playback capability for CD-RW, DVD-RW, DVD-R, DVD+RW or
DVD+R discs will vary according to the quality of the disc. On some
occasions it is possible that these discs may not play on the DVD 38.
• Both 5-inch (12cm) and 3-inch (8cm) discs may be used.
• Load CDs or DVD-Audio discs with the label side up.
• Load DVD-Video discs with printed labels label side up. If the disc
contains both standard and high-definition (not HD-DVD or Blu-ray
Disc) versions of the program, make sure the desired label faces up.
• Some DVD-Video discs are double-sided. The title information for
these will be printed on the inner ring of the disc, very close to the
center hole. The title for the side you wish to play should be facing up.
After a disc is properly loaded, press the Open/Close Button to close
the disc drawer. After the drawer closes, the LOADING message will
appear in the Main Information Display while the unit is determining the
type of disc (DVD-Video, DVD-Audio, CD, VCD, JPEG, WMA or MP3)
and is reading the data for track, chapter, title and other information
about the disc.
Figure 31 – Player Information Screen (WMA Disc)
• VCD2.0 discs will begin play automatically, similar to a conventional
audio CD. VCDs containing raw MPEG files may play, depending on
how the disc was created.
If a disc is already in the drawer when the unit is turned on, it will begin
playing. If the disc was stopped using the Resume function, playback
will begin from the point where it was stopped. If the disc was stopped
by pressing the Stop Button twice, the disc will begin playing from its
beginning. If the Disc Recognition feature was turned on in the System
Setup menu (see Figure 20), a screen will appear asking you whether to
begin playback from the beginning of the disc, or from the point where
playback was stopped during the last viewing session. See Figure 32.
Next, the applicable Disc-Type Indicator will light up in the front-panel
display. If the disc is a DVD, CD or VCD2.0 disc, it will automatically
begin playing. The disc’s track and timing information and other relevant
data will also appear in the Main Information Display.
Any time a control button is pressed, an icon will appear in the upper
right corner of the screen to indicate the player’s action. These icons
include the standard transport modes (play, stop, pause, forward and
reverse fast and slow search, track skip), the opening or closing of the
disc drawer, or the prohibit icon (Ø) if the command action is not avail-
able at that time or for that disc. As explained in more detail below,
pressing the Status Button displays the Status Banner for DVDs, and
pressing the Info Button displays the Player Information submenu.
• When a DVD is detected, playback will automatically begin and the
screen will show the program or the disc’s menu, depending on how
the disc was created.
• If a CD is detected, playback will begin automatically, and the Player
Information screen will appear. See Figure 30.
Figure 32 – Disc-Recognition Resume Screen
33
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Playback Control
See Figure 33 for reference to the transport controls described below.
NOTE: Playback of a disc with 96kHz/24-bit audio requires the
use of circuitry normally used for other features. Accordingly, the
Slow Play Reverse and Step Advance features are not available
with these discs.
• When a camera icon appears on screen, or the Angle Indicator
appears on the front panel, it indicates that there is multiple-angle
information on the disc being played. To change the angle, press the
Angle Button repeatedly until the desired angle view appears. An
on-screen banner message will indicate the current angle view.
• To illuminate the buttons on the remote control so that they may be
seen in low-light conditions, press the Light Button.
The availability of the Zoom, Repeat, Repeat A-B and Random functions
depends on the type of disc. In addition, the availability of the Player
Information screens and Status Bar vary from one disc type to another.
These features are described in the following sections describing play-
back of DVDs, CDs, MP3s, WMAs, JPEGs and VCDs. Programming
playlists is explained after the section on VCDs.
Figure 33 – Transport Controls
• To momentarily pause playback and freeze the current picture frame
on a DVD, press the Pause Button. To resume playback after pressing
the Pause button, press the Play Button.
Video Off Feature
• To move forward or backward through the tracks on a DVD-Audio
disc or CD, or the chapters on a DVD, press the Skip Forward/
Reverse Buttons on the front panel or the Previous/Next Buttons
on the remote.
The Video Off feature is available during playback of audio-only discs,
such as CD, DVD-Audio, MP3 or WMA discs. Although the video
circuitry is electrically isolated from the audio section, some users may
prefer to turn the video displays off during audio playback to prevent any
possibility of interference between audio and video. You may also wish
to turn the video display off if you find the menu system distracting or
unnecessary during audio playback.
• To move forward or backward through the DVD or CD disc being
played at fast speed, press the Search Forward/Reverse Buttons on
the remote, or press and hold the front-panel Skip/Search Buttons
briefly until fast play begins and then release them. Once one of these
buttons is pressed, the fast search will continue until the Play Button
is pressed. Each additional press of the Search Forward/Reverse
Buttons will cycle through the five available fast-search speeds: 2X,
4x, 8x, 20x, 100x.
IMPORTANT NOTE: It is strongly recommended that plasma
and CRT video display owners use the Video Off feature to
avoid burn-in, especially as some audio discs display still
images continuously.
NOTE: Fast search is available when DVD-Audio and MP3
and discs are playing, but not for WMA discs. Search speeds
available may vary for different types of discs.
To turn the video displays off while an audio disc is playing,
press the Video Off Button. Press the button again to restore the
video output. The V-Off Indicator will light in red to remind you
that the video displays have been turned off. The video output
will automatically be restored each time the DVD 38 is turned on.
• When a DVD or VCD is playing, you may move forward or backward
through the disc in slow motion by first pressing the Pause Button and
then pressing the Search/Slow Forward or Reverse Buttons. Each
additional press of the buttons will cycle the player through one of the
four forward slow-play speeds: 1/2x, 1/4x, 1/8x or 1/16x, or one
of the two reverse slow-play speeds: 1/2x or 1/4x. Press the Play
Button to resume normal playback.
NOTE: There is no audio playback during fast or slow-forward
or -reverse play. This is normal for DVDs, as surround proces-
sors cannot process the digital audio streams during slow
modes. Slow-play is available for VCDs, but not for audio CDs,
MP3s or WMAs. Slow-play speeds may vary for different types
of discs.
• To advance frame by frame while a DVD is playing, first press the
Pause Button, then press the Skip/Step (Previous) or Skip/Step (Next)
button repeatedly. Press the Pause or Play Button to resume normal
play. Frame-by-frame movement in reverse is not available.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
DVD Playback
Using a DVD’s Menu
The DVD system offers a producer the opportunity to include a wide
range of features on a disc, including multiple language tracks; subtitles
in a variety of languages; special information such as movie trailers and
cast information; and other customized information. In addition, produc-
ers may divide a movie or program into chapters that allow for quick
access to specific parts of the program. These chapters may be accom-
panied by thumbnail pictures of a scene from the specific chapter to
help you select the desired spot on the disc.
Figure 34 – Zoom and Navigation Buttons
• To use the Zoom feature, press the Zoom Button while a disc is
playing or paused. See Figure 34. Each press of the button will
increase the zoom-in effect. When you have cycled through all
four steps (three steps of enlargement for VCDs), the picture will
return to normal size.
When a disc is playing, press the Disc Menu Button to pause playback
and display the disc’s menu. As there are no hard rules about style and
contents for DVD menus, the way they appear on the screen and the
information they contain will vary from one disc to another. However, the
following general rules apply to most menus:
• When the Zoom feature is activated, you may use the Navigation
Buttons to explore the enlarged picture once the information box with
the zoom ratio and playback time no longer appears on the screen.
• You may move through the options on a menu using the Navigation
Buttons, as the disc’s programming allows. The option selected will
typically be highlighted in a certain color or inside an outline box.
• Some discs are created in a way that prevents the Zoom feature
from operating. In addition, the Zoom feature will not operate on disc
menus and may not operate on subtitles.
• To select a highlighted option, which may either play a portion of the
disc or move to a submenu, press the Enter Button.
Playback Resume
• On some discs, when you select the DVD menu during the playback
of a movie, the disc will return to the point in the program where the
menu was selected by offering a “Play Movie” option. Press the Enter
Button or Play Button to resume play. However, not all discs offer this
feature, and selecting the menu while playing a movie may mean that
you will have to go back to either the beginning of the program or the
start of a chapter. This feature is out of the control of the DVD 38, as
it is set by the disc’s internal programming.
The DVD 38 offers a “Resume” feature for DVD playback that is differ-
ent from the conventional “Stop” function you may be used to on CD
players. When the Stop Button is pressed once, the disc will stop and
Resume will appear briefly in the upper right corner of the video screen
and in the Main Information Display. While the Resume feature is active,
the disc’s position is entered into the unit’s memory so that when the
Play Button is pressed to resume playback, the program will continue
from the point where the Stop Button was pressed. To completely stop
playback, press the Stop Button twice.
NOTE ON PROHIBITED FUNCTIONS
You may resume a DVD (Audio or Video), CD, VCD with Playback
Control, MP3 or JPEG disc after placing the DVD 38 in Standby mode.
Resume will not operate for WMA files or for VCDs that do not have
playback control.
The DVD 38 is capable of all the features and options covered
by the DVD standards. However, not all discs will function identi-
cally, and some discs will not have many of the features of the
DVD system. For example, most current DVD discs do not take
advantage of the multiple-angle feature.
Disc Recognition
When you press a button and the player displays the “Function
Prohibited” icon “Ø”, this is an indication that the disc has not
been programmed for that function. In addition, it is common
for the producers of DVD discs to block the use of certain func-
tions during only some parts of a disc. For example, many discs
prohibit the use of fast-play buttons or prohibit access to the
Chapter Menu display during the playback of copyright notices,
studio logos, movie credits or trailers.
When the Disc Recognition feature is turned on in the SYSTEM SETUP
menu, you may press the Stop Button either once (to enter Resume
mode) or twice (to enter Stop mode) and remove the DVD from the
player. Even if you turn the DVD 38 off, the next time you insert that
DVD, you will be presented with the option of either starting playback
from the beginning, or resuming playback from the point at which you
stopped previously. See Figure 32. The DVD 38 can recognize up to
five discs total.
Zoom
Player Information Menu
The DVD 38’s advanced digital video processing circuits include a
Zoom feature that allows you to enlarge the image of a DVD, VCD or
JPEG for closer examination of a particular part of the picture. Four
steps of enlargement are available.
The DVD 38’s PLAYER INFORMATION menu displays disc information
and enables you to program playback modes. Press the Info Button to
display the PLAYER INFORMATION menu. See Figure 35.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
aspect ratio on one side of the disc, and a standard aspect ratio on
the other.
• Video Standard: The disc’s format is shown here. For Region 1 players,
this will normally be NTSC, although some DVDs that are open region
(playable in all regions) may be in the PAL format. The DVD 38 will
convert the video to the NTSC format used by your television.
• Scan Type: This line displays whether the video program on the
DVD was recorded with a progressive- or interlaced-scan rate. It also
displays how the program is being played back, based on the setting
established in the VIDEO SETUP submenu.
Figure 35 – Player Information Screen
The PLAYER INFORMATION menu has three submenus, which may be
accessed by using the Navigation Buttons to highlight the submenu’s
icon, and pressing the Enter Button to select it. These submenus are
different from the Setup menus in that many items are for display only
and cannot be changed using the menu system.
• Audio Resolution: This line displays the sample rate and bit rate for
the current audio format.
• Audio Format: This line displays the current audio track, such as
Dolby Digital 5.1 or Linear PCM.
PLAYBACK INFO Submenu: This submenu displays basic disc and
playback mode information. See Figure 36. Access this submenu by
highlighting the Info icon (top icon with a small “i”) and pressing the
Enter Button. See Figure 36.
• Video Bit Rate: This line displays the video bit rate up to the maximum
of 10 Mbps. This indication will vary as a disc is played in response to
changes in the amount of compression that was applied to the video
signal when the disc was created. Thus, as shown in Figure 35, when
the disc is stopped or paused, this line will remain blank.
When you have finished viewing the Player menus, press the Info or
Clear Button to remove the displays from the screen and return to
normal play.
On-Screen Status Display
When a DVD is playing, you may press the Status Button at any time to
view a quick summary of the disc’s playback status. The Status Bar not
only gives you a snapshot of the unit’s current state, it also provides an
easy way to select a different group, title, chapter or track, or use the
time search feature. See Figure 37.
Figure 36 – Playback Info Submenu
• Disc: This line displays the disc type, such as DVD-Video.
• Disc ID: If the disc is encoded with an identification label, such as
a movie title, it will appear here.
• Playlist: This line indicates whether playback will occur in the disc’s
order, or following a programmed playlist. For DVDs this line will
always indicate playback in the disc’s order, as programmed play
is not available for DVDs.
Figure 37 – Status Bar
• Group/Title: For DVD-Video discs, this displays the current title
number and the total number of titles on the disc. For DVD-Audio
discs, the current group number and total number of groups are
shown.
• Repeat: This line displays the current repeat mode, or Off if Repeat
mode is not active.
• Chapter: For DVD-Video discs, this shows the current chapter and
the total number on the disc. For DVD-Audio discs, the current and
total tracks are shown.
PROGRAM submenu: The Program submenu is not available for DVDs.
DISC INFO Submenu: This submenu displays detailed information
about the disc content (see Figure 35). You will not be able to make
any changes to the items on this submenu. However, you may use the
VIDEO SETUP submenu to change the DVD 38 player settings for video
aspect ratio or scan type.
• Play Mode Icon: This displays the current play mode icon;
i.e., Play ›, Pause , Stop Í.
• Time Display: This section of the display shows the time correspon-
ding to the type of display indicated in the Time Display Type. The
Time Search function enables you to start playback at any point in the
program. Use the ‹/› Navigation Buttons to highlight this display.
You may then use the Numeric Keys to enter the numbers correspon-
ding to the time on the disc from which you wish play to commence.
Press the Enter Button and play will begin at the selected time position.
• Disc: This line displays the disc type.
• Disc ID: If the disc is encoded with an identification label, it will
appear here.
• Aspect Ratio: This line displays the aspect ratio of the video content
on the disc, and the format in which it is being played back according
to the setting established in the VIDEO SETUP submenu. Some discs
may contain two versions of the same program with a widescreen
• Time Display Type: This section identifies the type of information
in the Time Display section of the display. Use the Navigation Buttons
36
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
to select this setting, and each subsequent press of the Enter Button
will change the time display from Title Elapsed, to Title Remaining,
to Chapter Elapsed to Chapter Remaining, and cycle back to Title
Elapsed. The time displayed on screen and in the front-panel
Information Display will change accordingly. For DVD-Audio discs,
the time display options are Group Elapsed, Group Remaining, Track
Elapsed and Track Remaining.
Figure 39 – Audio Status Bar
Each press of the Audio Select Button or the Enter Button will change
the current audio soundtrack. Don’t press any of the Numeric Keys to
select an audio track; doing so will change the chapter or track.
When the desired selection appears, press the ‹/› Navigation Buttons
so that Done is highlighted, and then press the Enter Button to remove
the banner display and return to normal playback.
• Time Bar: This display is a graphic representation of the time elapsed
for the title being played. As the disc plays, the number of bars will
increase to reflect approximately what percentage of the title has been
played thus far. It is not affected by changes to the Time Display Type.
NOTES ON AUDIO TRACKS:
• Not all discs contain multiple audio soundtrack choices.
Check the information on the disc jacket to see what audio
languages or format options are available.
Titles and Groups
To select a title or group, first press the Status Button so that the Status
Display appears. Navigate so that the Current Title or Group is highlighted.
Use the Numeric Keys to enter the desired title/group and it will begin
playing immediately. See Figure 38.
• Some DVDs do not allow direct selection of the audio track
during playback. For these discs, you must change the audio
soundtrack using the disc’s menu system. Press the Disc
Menu Button to display the disc’s menu and then use the
Navigation Buttons to make your selection following the
navigation scheme of the individual disc.
Figure 38 – Selecting a Title
• When you change the audio soundtrack or language with the
Audio Select Button on the remote control as shown above,
you only override the audio language setting established in the
AUDIO SETUP menu for the disc currently being played. The
unit will revert to its default setting with the next disc.
If a “ø” icon appears when you attempt to select a new title (group),
this is an indication that the disc does not allow the title (group) to be
changed in this manner, even though a list of numbers will appear. This
is a function of the way the disc was created and is not a flaw in the
DVD 38.
Subtitles (DVD-Video Discs Only)
For some discs, you may press the Title or Audio Button during playback
to change the current title or group. Other discs will switch to the disc
menu, and some discs may simply restart play from the beginning of the
current title or group. This is a function of how the disc was authored,
and does not reflect a problem with the DVD 38.
Many DVDs contain one or more subtitle languages. The default subtitle
language is set in the SYSTEM SETUP menu, but you may also turn the
subtitles on or off, or change the language at any time during a disc’s
playback.
To change the subtitle language or turn the subtitles on or off, press
the Subtitle Button to display the Subtitle banner and show the current
configuration. See Figure 40. Each press of either the Subtitle Button
or the Enter Button will change the current subtitle language, or turn
subtitling off.
Chapters and Tracks
To select a chapter for DVD-Video discs or a track for DVD-Audio
discs, first press the Status Button so that the Status Display appears.
The Current Chapter or Track Number will be highlighted. Use the
Numeric Keys to enter the desired chapter/track, and it will begin
playing immediately.
To select a specific chapter or track on a DVD at any time during play-
back, simply press the number corresponding to the chapter or track
you wish to view using the Numeric Keys. You may also move one by
one through the chapters or tracks at any time by pressing the Skip
Reverse (Previous)/Skip Forward (Next) Buttons.
Figure 40 – Subtitle Banner
When your desired selection appears, press the ‹/› Navigation
Buttons until Done is highlighted and then press the Enter Button to
remove the banner display and return to normal playback.
NOTE: Due to the variations in how DVD discs are authored,
subtitle languages displayed by the DVD 38 may not accurately
reflect the actual languages available on the disc. It is recom-
mended that subtitles be selected using the disc’s menu.
Audio Soundtracks
Many DVDs contain more than one audio soundtrack. On many discs,
you will find multiple languages, while others offer a choice of different
audio formats or mixes (e.g., Dolby Digital or DTS). Some will also con-
tain commentary from the director or stars. The default audio language
is set in the AUDIO SETUP menu.
Angles (DVD-Video Discs Only)
Some DVDs contain multiple-angle views, which allow the disc’s creators
to provide different camera views of the same scene. In many cases
the disc will alert you to the presence of multiple angles by showing a
camera icon or other indication, but in any case where multiple-angle
To change the audio soundtrack, press the Audio Select Button to
display the Audio banner and show the current audio soundtrack
configuration. See Figure 39.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
material is available, if the Show Angle Icon setting in the SYSTEM
SETUP menu has been set to On, the Multiple Angle Icon will appear on
screen briefly at the beginning of the passage where multiple camera
angles are available, and the Angle Indicator will light in the front panel
Information Display.
1. Press the A-B Repeat Button (see Figure 44) on the remote when
you want to choose the beginning point; the “REPEAT A-” message
will appear on screen. The “A” indicator will light in the front-panel
display.
2. Press the A-B Repeat Button again to choose the end point. Repeat
A-B has been set, and the A-B section will be played continuously.
See Figure 45.
When multiple angle views are available, press the Angle Button to
change the view. See Figures 41 and 42. The current angle number
and total available angles will be displayed. Each press of the Angle
Button will change the current camera angle. If you press the Angle
Button during a section without multiple views, onlly one view will
be available.
Figure 45 – Repeat A-B Message
3. Press the A-B Repeat Button on the remote again to cancel Repeat
A-B mode.
Figure 41 – Angle Button
Figure 42 – Angle Banner
When your desired selection appears, press the ‹/› Navigation
Buttons until Done is highlighted and then press the Enter Button to
remove the banner display and return to normal playback.
Repeat Play
The DVD 38 offers several repeat functions that allow you to take
advantage of the capacity of the unit for unattended playback. Press the
Repeat button once to display the Repeat Message on-screen. See
Figure 43. Press the Repeat Button again to cycle through the options.
Figure 43 – Repeat Message
• Repeat 1: Repeats the DVD chapter or DVD-Audio track currently
being played until the disc is manually stopped. The Repeat (“Rep.”)
indicator will light in the front-panel display, and the Chapter or Track
indicator will flash.
• Repeat Title or Group: This mode repeats the title or group currently
being played until the disc is manually stopped. The Repeat (“Rep.”)
indicator will light in the front-panel display, and the Title or Group
indicator will flash.
A-B Repeat Play
The Repeat A-B function allows you to select any portion of a DVD-
Video disc and have it repeat continuously until stopped.
To initiate a Repeat A-B playback sequence, follow these steps while
a disc is playing:
Figure 44 – A-B Repeat Button
38
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
CD Playback
Many functions of the DVD 38 operate the same way for CD playback
as for DVD play; however, there are some important differences. When
a CD is loaded, the DVD 38 will automatically display the Player
Information menu. See Figure 46. Status banners are not available dur-
ing CD play. Features unique to CD play are described in this section.
Player Information Menu
The DVD 38’s Player Information menu displays disc information and
enables you to program playback modes. If it is not already on screen,
press the Info Button to display the Player Information menu. See
Figure 46.
Figure 47 – Program Submenu
PROGRAM Submenu: This submenu lets you program a playlist.
The PROGRAM submenu is only accessible for CD’s (see Figure 47).
• Disc: This line displays the disc type.
• Audio: This line displays the type of audio that was recorded on
the disc, usually Stereo.
• Playlist: With this line highlighted, press the Enter Button to change
the order in which the tracks are played from the order in which they
appear on the disc (Disc’s order) to a playlist order which you may
program (Programmed order). If you select Programmed order, a list
of program steps and the track programmed for each step will appear
at the bottom of the screen (see Figure 54). You may enter a track
number using the Numeric Keys and then use the Navigation Buttons
to program another track. To remove a track from the playlist, press
the Clear Button. You may not enter a track more than once in the
playlist, if it appears in an earlier step. However, you may use the
Repeat function while the playlist is playing. After you have finished
programming the playlist, press the Play Button to begin play. See
the Programming a Playlist section for more information.
Figure 46 – CD Player Information Screen
The Player Information menu has three submenus, PLAYBACK INFO,
PROGRAM and DISC INFORMATION, which may be accessed by using
the Navigation Buttons to highlight the submenu’s icon, and pressing the
Enter Button to select.
PLAYBACK INFO Submenu: This submenu displays basic disc and
playback mode information. See Figure 46.
DISC INFORMATION Submenu: This screen displays abbreviated track
and playback information, and allows you to change the time display
setting.
• Disc: This line displays the disc type, such as CD-DA (Compact Disc
Digital Audio).
• Playlist: You may choose to play the tracks in order as they appear
on the disc, or you may program a playlist containing some or all of
the tracks in the order in which you wish to hear them. This line
indicates which of these two modes has been selected. To change
this setting, use the PROGRAM submenu, as explained in the
Programming Playlists section.
• Repeat: With this line highlighted, press the Enter Button or the
Repeat Button to activate Repeat mode. Each press will change the
repeat mode from Repeat 1 (repeat one track) to Repeat All (repeat
all tracks on the disc) to Repeat Off. Repeat A-B is not selected using
this setting.
Figure 48 – Disc Information Submenu
The information at the top of the screen provides the same information
on the disc type, audio format, playlist setting, Repeat play setting and
Random play setting as on the other submenus. The following additional
information appears next:
• Random: With this line highlighted, press the Enter Button or the
Random Button to activate Random play mode, in which the tracks on
the disc are played in random order. Each press will toggle between
turning Random play on or off.
• Track: This line displays the current track on the left, and the total
number of tracks on the disc to the right. When the current track
number is highlighted, you may use the Numeric Keys to skip to a
new track. The new track will begin playing immediately.
• Track List: A list of tracks on the disc will appear. Use the Navigation
Buttons to scroll through the list. Press the Enter Button or the Play
Button while a track is highlighted to begin play.
• Play Mode Icon: This icon appears to the right of the Track display
and indicates the current playback mode.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
• Time: This section consists of three lines:
• Repeat Folder: For MP3s, WMAs and JPEGs, repeats all tracks with-
in the current folder until play is manually stopped. The Repeat indica-
tor will light in the front-panel display.
Track Elapsed: Displays the elapsed or remaining time
of the current track.
Each press of the Repeat Button (see Figure 50) cycles through the
available Repeat options (except Repeat A-B). In addition, the Repeat
setting in the Player Information menu will change.
Disc Elapsed: Displays the elapsed or remaining time of the disc.
Elapsed Time Bar: Displays a temperature bar reflecting the
percentage of the disc that has been played.
Use the Navigation Buttons to highlight either Track Elapsed or Disc
Elapsed, and each press of the Enter Button will toggle between the
elapsed and remaining settings. The time displayed to the right and
in the front-panel Information Display will change accordingly.
Figure 50 – Repeat, A-B and Random Buttons
• Time Search: The Time Search function enables you to start play-
back at any point in the track. Use the Navigation Buttons to highlight
the track time display. Press the Numeric Keys to enter all six digits,
including leading zeros if needed, to select the desired starting time,
followed by the Enter Button.
A-B Repeat Play
The Repeat A-B function allows you to select any portion of a CD and
have it repeat continuously until the unit is manually stopped.
To initiate a Repeat A-B playback sequence, follow these steps while
a disc is playing:
When you have finished viewing the Player menus, press the Clear
Button to remove the displays from the screen.
1. Press the A-B Repeat Button on the remote (see Figure 50) when
you want to choose the beginning point; the Repeat A- icon appears
on screen and on the front panel to indicate the beginning of the
passage to be repeated.
Tracks
To select a track, make sure the PLAYER INFORMATION menu is on
screen. Press the Info Button to activate it if necessary. Next, press the
Navigation Buttons so that the Track is highlighted. Use the Numeric
Keys to enter the desired track, and press the Enter Button to begin
playing the new track.
2. Press the A-B Repeat Button again to choose the end point. Repeat
A-B has been set, and the A-B section will be played continuously.
3. Press the A-B Repeat Button again to cancel Repeat A-B mode.
During playback, you may move one by one through the tracks at
any time by pressing the Skip Reverse (Previous)/Skip Forward (Next)
Buttons. When you press the Previous or Skip Reverse Button once, the
player will return to the start of the current track. Additional presses of
either button will step back through the available tracks, one at a time.
See Figure 49.
Random Play
The Random Play function will play all of the tracks on a CD in a
random order, as selected by the DVD 38. Once the DVD 38 has
played all of the tracks on the disc once, it will stop.
Select the random mode by pressing the Random Button on the
remote. See Figure 50. Each press of the Random Button will toggle
the setting between “Off” and “On”, meaning that the remaining tracks
on the disc will be played in random order.
Figure 49 – Skip Reverse (Previous) and Skip Forward (Next) Buttons
The Random Indicator in the Front-Panel Information Display will light
when the Random setting is on.
NOTE: When a JPEG, MP3 or Windows Media disc is playing,
a special screen will appear. See the section describing those
types of discs for more information.
Repeat Play
The DVD 38 offers several repeat functions for CDs that allow you to
take advantage of the capacity of the unit for unattended playback:
• Repeat Program: Repeats the current playlist if Programmed Order
has been selected at the Playlist setting.
• Repeat 1 Track: For CDs, VCDs, MP3s and WMAs, repeats the track
or file currently playing until the disc is manually stopped. The Repeat
and 1 indicators will light in the front-panel display.
• Repeat Disc: For CDs, VCDs, MP3s, WMAs and JPEGs, repeats
the entire disc until play is manually stopped. The Repeat and All
indicators will light in the front-panel display.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
MP3 or WMA Disc Playback
MP3, Windows Media and JPEG Playback
MP3 and WMA discs may contain 200 or more tracks. To get the best
view of all tracks on the disc, including their names, and to select them
comfortably, use the on-screen display rather than the front-panel dis-
play. The front-panel display will only show the number and the elapsed
time of the track being played.
The DVD 38 will recognize data on CD-ROM discs recorded in the
MP3, Windows Media 9 (WMA) or JPEG formats, including images
stored on Kodak Picture CDs. You may also play discs with more
than one of the three formats.
The specific file types that may be played on the DVD 38 are:
The supported bit rate for WMA files is between 64kbps and 320kbps.
The supported bit rate for MP3 files is between 32kbps and 320kbps.
• MP3 Files: MP3 is a popular audio compression format that was
developed by the Motion Picture Experts Group as part of the MPEG-
1 video compression format. Depending on the specific MP3 encoder
used, file size is greatly reduced so that you store many more songs
on one compact disc than in the standard audio CD format. MP3 is
also used to download audio files to computers for home use. In
order to play an MP3 file on the DVD 38, the disc may not contain
any encryption or coding that prevents playback. Always be certain
that you have, or have purchased, the proper rights or authorization
before creating a CD-ROM with MP3 or any other codec format.
• To expand a folder (if any), press the Navigation Buttons until the
desired folder name is highlighted, then press the Enter Button.
• To collapse a folder (so that you can select another folder on the
disc), use the Navigation Buttons to highlight the folder icon at the
top of the track list and press the Enter Button.
• To select a track, press the Navigation Buttons until the desired track
name is highlighted. To start play of the selected track, press the Enter
or Play Button.
• WMA Files: WMA (Windows Media Audio) is an audio compression
format developed by the Microsoft® Corporation for use with its
Windows Media Player. WMA files may be created with greater
compression than MP3 without sacrificing audio quality so that even
more songs may be recorded on a disc. There have been a number
of versions of Windows Media, and the DVD 38 is compatible only
with files that end in the “wma” extension and that were recorded
using the Windows Media Series 9 encoding, but only up to 320kbps.
During MP3/WMA playback, some of the standard CD/DVD playback
controls operate in their normal fashion (refer to Figure 33):
• JPEG Files: “JPEG” is the acronym used to identify image files
recorded according to specifications established by Joint Photographic
Experts Group for compressing still images. Identified by the file
extension “jpg” when they are recorded on most computers, JPEG
files may be created by a digital still camera and then edited and
“burned” to a disc in your personal computer, recorded on a
CD-ROM disc from film images by a photo processor, or scanned
from printed photos into your personal computer and then burned
onto a CD-ROM.
Figure 33 (repeated) – Transport Controls
• You may skip forward to the next track on the disc by pressing the
Skip/Next Button.
Discs containing MP3, WMA or JPEG files are navigated and controlled
a little differently than standard DVDs and CDs. When a disc containing
one or more of these types of files is loaded in the DVD 38, the
PLAYER INFORMATION menu screen will appear. See Figure 51.
• You may skip back to the previous track on the disc by pressing the
Skip/Prev Button twice.
• Press the Pause Button to momentarily stop playback. Press the Play
Button to resume play. Press the Stop Button to enter stop mode.
• Press the Search Forward or Search Reverse buttons for fast search of
a track. Press the Play ›, Pause or Stop Button Í to end fast play.
• Slow-play is not available during MP3/WMA playback.
• You may play an MP3 or WMA disc in random mode by pressing the
Random Button. See Figure 50.
• The Repeat function may be accessed during playback of an MP3 or
WMA disc by pressing the Repeat Button on the remote. See Figure
50. Repeatedly press the Repeat Button to scroll through the options
of Repeat 1 (repeat one file), Repeat All (repeat all files) or Repeat
Folder (repeat all files within the current folder). The next press will
turn the repeat function off. Repeat A-B is not available during
MP3/WMA playback.
Figure 51 – Player Information Screen For WMA Disc
This screen will display a list of the main folders contained on the disc
The elapsed time will appear in the upper right corner of the screen. It
isn’t possible to change the time display, and the Time Search function
is not available.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
You may use the Zoom Button to enlarge a JPEG image, and the
Navigation Buttons to explore the enlarged image.
NOTES ON MP3 AND WMA PLAYBACK:
• During playback, the front-panel display and the time indicator
on the screen above the list will show the elapsed time of the
track being played. Other time display options are not available
with MP3/WMA playback.
You may view thumbnails of the images in an expanded folder by press-
ing the Disc Menu Button. When the images appear on screen, you may
use the Navigation Buttons to move the picture frame until the desired
image is selected. Press the Enter Button to display a full-size view of
that image. See Figure 52.
• The DVD 38 is only compatible with standard MP3- and
WMA-encoded discs. Other compressed audio formats used
for Internet audio downloads will not play on the DVD 38.
• Due to the differences in various versions of the MP3 and
WMA formats, and the many differences between the CD-R
machines used to record discs on a computer, it is possible
that some discs may not play on the DVD 38 even though
they will work on a computer. This is normal and does not
indicate a fault with the unit.
Figure 52 – Thumbnail Image Menu
• When a multisession disc with both standard CD audio and
MP3 or WMA content is in use, the DVD 38 will play only the
CD audio sections of the disc. Track numbers will be visible in
the display, but the files will not be decoded.
• If a disc containing MP3, WMA and/or JPEG files is created
in more than one session, the DVD 38 may not recognize
files added during the later sessions, especially if the disc was
finalized after the first session.
• When a disc with multiple folders is playing, only tracks from
one folder can be displayed and played at a time. Select the
desired folder and press the Play Button or Enter Button to
start the first track. To see and play tracks from other folders,
you must first collapse the current folder as appropriate and
use the Navigation Buttons until the desired folder is selected.
Press the Enter Button to expand the folder, navigate to the
desired track, and press the Enter or Play Button to begin play.
• Only stereo-audio playback is available for MP3 and WMA
discs.
• Programmed playlists are not available for MP3/WMA discs.
• Use the Navigation Buttons to select the DISC INFO Submenu
icon on the left side of the screen, and press the Enter Button
to view it. If the disc contains ID3 tag information, then the
current MP3 track information – song title, artist, album, year,
genre, and any comments will be displayed. For WMA and
JPEG files, only the file name will appear.
JPEG Playback
The DVD 38 is capable of recognizing JPEG still-image files and dis-
playing them. When a disc or folder containing JPEG files is loaded, the
JPEG Disc-Type Indicator will light in the Main Information Display. The
disc will immediately begin displaying the images on the disc in order.
When viewing JPEG images, the Angle Button may be used to rotate
the image. With the image onscreen, press the Angle Button once to
display the current orientation of the image, usually +0. Press the Angle
Button again to rotate the image clockwise 90 degrees. Each additional
press of the Angle Button will continue to rotate the image clockwise by
90 degrees.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
The Status Bar will appear the same as for DVDs (see Figure 53),
except that the current and total track numbers will be shown, rather
than the title, and there is no chapter display. If PBC is off, you may
select the track number and change it to skip to another track. You
may also use the Time Search function to begin play at a desired
place. You may change the time display from Track Elapsed, to Track
Remaining, to Disc Elapsed, to Disc Remaining, and back to Track
Elapsed, just as with DVDs. The elapsed time will appear as a graphic
temperature bar, with additional lines added as more of the track or
disc is played.
VCD Playback
VCD, a video-playback format that predates DVD, is based on a different
compression format than DVD and uses a recording method that is
similar to CD. Although the DVD has, for the most part, replaced VCD
as a format, the DVD 38 offers VCD playback so that you may play your
existing library of VCD discs, or home movies that you have recorded
as VCDs on your computer.
There are two versions of the VCD format: an early version which is
simply called “VCD” and a later version with Playback Control that’s
called “Version 2.0” or “PBC.” The DVD 38 is compatible with both
forms of VCD, although playback will vary according to which version
is used and the specific way in which the disc was created.
Figure 53 – VCD Status Bar
Even though VCD discs provide video, because the format is based on
CD technology, the playback functions for a VCD disc are similar to CD.
To play a VCD disc, place it in the DVD 38 as you would do with any
other CD or DVD disc. The unit takes a few seconds to read the disc’s
contents; the VCD Disc-Type Indicator in the front-panel display will light
and the disc will begin playing.
Zoom
The Zoom function is available for VCDs by pressing the Zoom Button.
Repeatedly pressing this button will cycle through the possible settings
of 1x, 2x and 3x zoom, as indicated on screen. After the enlargement
indication disappears from view, you may explore the image using the
Navigation Buttons.
Keep in mind that the exact level of functionality for any VCD will vary
widely and it is ultimately determined by the way the disc was created,
not by the DVD 38, particularly if the disc has been created under VCD
Version 2.0 with Playback Control (see “Playback Control”).
Playback Control
VCD discs made under the Revision 2.0 specification will usually offer
PBC playback control. The PBC Indicator in the front display will turn on
automatically with any VCD when the disc is played. With PBC, you can
select titles and navigate the disc as with DVDs. However, the access to
some functions may be prohibited by PBC playback control; in that
case, the prohibit icon will appear on screen.
When playing VCD discs, most standard DVD/CD playback controls are
used, including Play, Stop, Pause, Resume, Track Skip Forward and
Reverse, Slow Forward, Step Forward and Fast Forward. The Reverse
Search and Step Reverse functions are not available with VCDs.
You may access information on the disc by pressing the Info Button
on the remote. The availability of the Repeat and Random functions will
depend on whether PBC Support has been activated using the SYSTEM
SETUP submenu. With PBC Support on, Repeat and Random will not
be available.
When a VCD is made without PBC, the disc can be controlled the
same as an audio CD, but direct track access by entering a number
is not possible without opening the Status Bar. With PBC, many discs
include chapter selection menus that are similar to those found on
DVDs. However, on VCD discs, the disc menu (if any) is accessed and
controlled differently than on DVDs.
Repeat A-B is always available. Simply press the Repeat A-B Button
once at the beginning of the passage to be repeated, again at the end
of the passage, and a third time to cancel Repeat A-B mode.
• Play will start with the first track (which may be an intro), then proceed
to the VCD menu (if any) automatically.
NOTE: Discs containing raw MPEG files, without playback
control, are not technically Video CDs, and are played in
a different manner. When such a disc is loaded, the Player
Information menu will appear, with a list of folders or files,
similar to an MP3 disc. The disc directory is navigated using
the Navigation Buttons. Press the Enter Button to expand or
collapse a folder. Select the desired track, and press the Play
Button or the Enter Button to begin play. You will find that the
Stop, Pause, Track Skip Forward and Reverse, Slow Forward
and Reverse, Step Forward and Reverse, and Fast Forward
and Reverse Search functions are all available, depending on
how the disc was encoded. However, the Status Banner is
not available for these types of VCDs.
• The Next (Skip Forward) command will skip to the VCD menu from
the intro (Track 1) directly.
• Once the menu options appear on the screen, make your selection
by pressing the Numeric Keys that correspond to your desired choice.
The desired selection will begin playing automatically.
• Direct number entry without any VCD menu shown on-screen has no
effect – even when the Status Bar is on.
The Disc Menu Button used during DVD playback is not used for VCD
playback. Use of functions when PBC is on will vary according to the
disc type.
Status Bar
When playing VCD discs, it is possible to access the disc’s features
using the Status Bar. Press the Status Button to view it.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
3. Press the Info Button and navigate to the PROGRAM submenu, as
described above in Step 2 of the instructions for programming a
playlist. With the Playlist setting highlighted, press the Enter Button
Programming a Playlist
Programmed play allows you to select tracks on a CD for playback in
a specific order, skipping tracks you don’t wish to hear and reordering
other tracks to suit your tastes.
’
until the setting reads Disc s Order.
To program a disc for playback, follow these steps:
1. Load the desired disc, but stop play if it begins automatically. Playlists
may only be programmed in Stop mode.
2. Press the Info Button to display the PLAYER INFORMATION menu.
Use the Navigation Buttons to highlight the icon for the PROGRAM
submenu, and press the Enter Button to display it.
⁄ ¤
3. Use the
/
Navigation Buttons to highlight the Playlist setting.
Press the Enter Button so that the setting changes to Programmed
Order and a grid of program steps appears on the bottom of the
screen (see Figure 54).
Figure 54 – Programmed Play Screen
4. At this time the playlist will simply contain the tracks in the disc’s
order. Thus, Step P01 will display track 1 from the disc, Step P02
will display track 2 from the disc, and so forth. The track assigned
to Step P01 will be highlighted. Use the Numeric Keys to enter the
number of the track on the disc which you wish to hear first in your
playlist. When you have finished entering it, press the › Navigation
Button to move to Step P02.
5. Continue entering the disc track numbers into the desired program
step positions. You need not do so in step order; you may use the
Navigation Buttons to navigate to any step in the list.
6. Press the Clear Button to remove a track from the playlist.
7. Although you may enter fewer programmed steps in your list than the
number of tracks on the disc, you may not repeat tracks within the
list. However, while the playlist is playing, the normal Repeat functions
will be available.
8. When you have finished entering all of the tracks in your playlist,
press the Play Button to begin playback of your programmed list.
During programmed play the track number shown in the front-panel
display will reflect its normal order on the disc. However, the Program
Indicator will light to remind you that the disc’s tracks are playing in
programmed order.
To cancel programmed play, stop play and perform one of these steps:
1. Open the Disc Drawer.
2. Press the Playlist Button. The Playlist Banner will appear on screen.
Each press of the Playlist Button will toggle the mode between
programmed order and disc order.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
SYMPTOM
CAUSE
SOLUTION
Unit does not turn on
• No AC power
• Make certain AC power cord is plugged into
a live outlet.
• Check to see whether outlet is switch-controlled.
Unit does not respond to
remote commands
• Weak batteries in remote
• Remote sensor is obscured
• Change remote batteries and insert with correct polarity.
• Make certain front panel sensor is in line of sight of remote
or connect an optional remote sensor.
No picture
• Intermittent connections
• Wrong input
• Check all video connections.
• Check input selection of TV or receiver.
• Progressive Scan output selected
• Use Progressive Scan mode only with compatible TV.
Press Scan Type Button to toggle to the correct resolution.
• HDMI Output is connected to a video • The HDMI Output may not be used with video displays that
display that is not HDCP-compliant
are not HDCP-compliant. Unplug the cable and select
another audio and video connection.
• Video Off feature active
• Wrong video output setting in
VIDEO SETUP menu
• Press Video Off Button to reactivate video circuitry.
• S- and component video are not available simultaneously.
Temporarily connect composite video to access Video Setup
menu and change Video Output setting to desired type.
Disc does not play
• Disc loaded improperly
• Incorrect disc type
• Load disc label-side up; align the disc with the guides and
place it in its proper position.
• Check to see that the disc is CD, CD-R, CD-RW, VCD, MP3,
WMA, JPEG, DVD-R/RW, DVD+R/RW (standard-conforming),
DVD-Audio or DVD-Video; other types will not play.
• Use Region 1 or Open Region (0) disc only.
• Invalid Region Code
• Rating is above parental control setting • Enter password to override or change rating settings.
No sound
• Intermittent connections • Check all audio connections.
• Incorrect digital audio input selection • Check digital audio settings on DVD 38 and on receiver.
• DVD disc is in fast or slow mode
• There is no audio playback on DVD discs during fast
or slow modes.
• Surround receiver not compatible
with 96kHz PCM audio
• Change PCM Limit setting in Audio Setup menu to 48kHz.
• DVD-Audio disc is loaded without
using analog audio connection
• Wrong bass management setting in
AUDIO SETUP
• Use 6-Channel Audio Outputs or Analog Audio Outputs.
• In order to hear a downmixed 2-channel signal at the Analog
Audio Outputs, make sure to change the Bass Management
setting to Stereo.
Picture is distorted or jumps
during fast forward or reverse play
• MPEG-2 decoding
• It is a normal artifact of DVD playback for pictures to jump
or show some distortion during rapid play.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
SYMPTOM
CAUSE
SOLUTION
Some remote buttons do not operate • Function not permitted at this time
during DVD play; prohibited symbol
Ø appears
• With most discs, some functions are not permitted at certain
times (e.g., Track Skip) or at all (e.g., direct audio track
selection).
The OSD menu is in a foreign
language
• Incorrect OSD language
• Change the display language selection in the SYSTEM SETUP
menu.
The Ø symbol appears
• Requested function not available
at this time
• Certain functions may be disabled by the DVD itself during
some passages of a disc.
Picture is displayed in the
wrong aspect ratio
• Incorrect match of aspect-ratio
settings to disc
• Change aspect-ratio settings.
Disc will not copy to VCR
• Copy protection
• Many DVDs are encoded with copy protection to prevent
copying to VCR.
Password not accepted
• Incorrect password being used or
password has been forgotten
• Stop play of disc and clear all displays from screen.
Press and hold Clear Button until the display blinks.
This resets the password and all settings to their defaults.
You will need to reenter all audio, video and system settings.
Screen Saver not activated
Cannot program playlist
• Screen saver will not activate when
cursor is in column of icons on left
side of screen
• Move cursor to main disc information or playlist area
to avoid burn-in on plasma and CRT displays.
• Programmed play is not available for • Programmed play is available only for CDs.
all disc types
• DVD 38 must be in Stop mode to
program a playlist
• Stop play of disc before programming a playlist.
In addition to the items shown above, additional information on troubleshooting possible problems with your DVD 38, or installation-related issues,
46
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD 38 TECHNICAL SPECIFICATIONS
Applicable Disc:
Frequency Response:
Disc formats:
5-inch (12cm) or 3-inch (8cm) DVD-
Video, DVD-Audio, standard-conforming
DVD-R, DVD+R, DVD-RW, DVD+RW, VCD,
CD, CD-R, CD-RW or MP3 discs
DVD video disc with Code 1 or 0 only
Single side/single layer, single side/dual
layer, dual side/dual layer
DVD Audio MLP lossless, Linear PCM,
MPEG, Windows Media® 9, Dolby® Digital
or DTS® audio discs
DVD (linear PCM):
2Hz – 22kHz +0/–0.5dB (48kHz sampling)
2Hz – 44kHz +0/–1.5dB (96kHz sampling)
2Hz – 88kHz +0/–0.5dB (192kHz sampling)
2Hz – 20kHz +0/–0.5dB
CD:
Region code:
DVD layers:
Signal/Noise Ratio (SNR):
Dynamic Range:
105dB (A-weighted)
DVD:
CD/DVD:
100dB (18-bit)/105dB (20-bit)
96dB (16-bit)
Audio formats:
THD/1kHz:
DVD/CD: 0.0025%
Still-image format:
Video Signal System:
HDMI™ Output:
JPEG
Wow & Flutter:
AC Power:
Below measurable limits
110–240V AC/50–60Hz
1 Watt (on/standby)/13 watts (max)
NTSC
Video: 480p, 720p, 1080i
HDMI Version 1.0-compliant
HDCP Version 1.1-compliant
Power Consumption:
Dimensions (H x W x D):
2" x 17-3/10" x 11-1/4"
(50mm x 440mm x 285mm)
Composite Video Output:
S-Video Output:
1V p-p/75 ohms, sync negative polarity
Weight:
6 lb (2.7kg)
Shipping Dimensions (H x W x D): 5" x 14-3/8" x 20"
(127mm x 365mmx 508mm)
8.8 lb (4kg)
Y/luminance:
C/chrominance:
1V p-p/75 ohms, sync negative polarity
0.286V p-p
Shipping Weight:
Component Video Output:
Analog Audio Output:
Y: 1V p-p/75 ohms, sync negative polarity
Pr: 0.7V p-p/75 ohms
Pb: 0.7V p-p/75 ohms
2V RMS (1kHz, 0dB)
The DVD 38 is Simplay HD™-verified for compatibility
via the HDMI connection with other Simplay HD-verified products.
Depth measurement includes knobs, buttons and terminal connections. Height measurement includes feet and chassis.
All features and specifications are subject to change without notice.
Harman Kardon and Logic 7 are registered trademarks, and Designed to Entertain is a trademark, of Harman International Industries, Incorporated.
Blu-ray Disc is a trademark of the Blu-ray Disc Association.
CEA (Consumer Electronics Association) is a registered trademark of the Consumer Electronics Association.
Dolby and Pro Logic are registered trademarks of Dolby Laboratories.
DTS, DTS-ES, DTS Neo:6 and DTS 96/24 are registered trademarks of DTS, Inc.
HD-DVD is a trademark of the DVD Format/Logo Licensing Corporation (DVD FLLC).
HDMI (High-Definition Multimedia Interface) is a trademark of HDMI Licensing LLC.
Kodak is a registered trademark, and Photo CD is a trademark, of Eastman Kodak Company.
SACD (Super Audio CD) is a trademark of Sony Corporation.
The Simplay HD™ logo and the Simplay™, Simplay HD™ and Simplay Labs™ trademarks are owned by Silicon Image, Inc. and are used under license from Silicon Image, Inc.
and/or Simplay Labs, LLC.
Microsoft, Windows and Windows Media are registered trademarks of Microsoft Corporation in the United States and/or other countries. WMA (Windows Media Audio) is a proprietary file
format developed by Microsoft.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited
viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
new products and/or special promotions.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY
is capable of recognizing JPEG files and enabling you to view them on
your video screen.
GLOSSARY
Aspect Ratio: This is a description of the width of a video image in
relation to its height. A conventional video screen is four units wide for
every three units of height, making it almost square. Newer wide-aspect-
ratio video displays are 16 units wide for every nine units of height,
making them more like the screen in a movie theater. The program
material on a DVD may be recorded in either format and, in addition,
you may configure the HS 300 to play back in either format, depending
on the features recorded on a disc.
MP3 Files: MP3 is an audio compression format that was developed
by the Motion Picture Experts Group as an adjunct to the MPEG-1 video
compression format. A number of encoding software programs are
available for transferring CDs and other audio programs into the MP3
format. The main benefit of MP3 is that it reduces the size of audio files
considerably, depending on the amount of compression selected during
the encoding process, enabling you to store many more songs on
one compact disc than in the standard audio CD format. The DVD 38
is capable of playing MP3 files stored on a disc using its advanced
graphic interface.
Chapter: DVD programs are divided into chapters and titles. Chapters
are the subsections programmed into a single title on a disc. Chapters
may be compared to the individual tracks on an audio CD. Press the
Disc Menu Button to see a listing of the chapters on a disc.
MPEG-2 files: MPEG stands for the Motion Pictures Expert Group,
which defines digital audio/video standards. The MPEG-2 format is
a method of compressing video presentations, and is the standard
generally used for television broadcasting and DVD, with some minor
modifications appropriate to each type of use.
Component Video: This form of video signal eliminates many of the
artifacts of traditional composite video signals by splitting the signal into
a separate luminance channel (the “Y” signal channel) and two color-
difference signals (the Pr and Pb signal channels). With a component
video connection, you will see greater picture resolution and eliminate
many picture imperfections such as the moiré patterns often seen on
check-patterned cloth. However, in order to benefit from component
video, you must have a video display with Y/Pr/Pb component video
inputs. Do not connect the component video outputs of the DVD 38
to the standard composite or S-video inputs of a TV or recorder.
Multiple Angle: DVDs have the capability to show up to four different
views of the same scene in a program. When a disc is encoded with
multiple-angle information, pressing the Angle Button will enable you to
switch between these different views. Note that, at present, few discs
take advantage of this capability and, when they do, the multiple-angle
technology may only be present for short periods of time within the disc.
Producers will usually insert some sort of icon or graphic in the picture
to alert you to the availability of multiple-angle scenes. In addition, the
DVD 38’s angle indicator will remain lit in the front-panel display for the
duration of multi-angle availability.
Group: The individual tracks on a DVD-Audio disc may be combined
into Groups. There may be more than one Group on a disc. Depending
on the way a disc’s producers create the program, the Groups can
contain different program material, or they may repeat the disc’s content
in different audio formats, such as 5.1 audio or high-resolution stereo.
Progressive Scan: Progressive-scan playback takes the original video
signal on the disc and formats it as a high-scan-rate output with twice
the scan lines of conventional video images. Progressive-scan outputs
must be connected to “digital-ready” or high-definition video displays,
regardless of the technology of the specific display (e.g., conventional
direct-view television, front or rear projector, plasma display panel or
LCD). In some cases, the displays may have special inputs for use with
high-scan-rate inputs, and in others you may need to make adjustments
to the display’s setup menus to make certain that the inputs used are
configured for an “HD” signal. Although the progressive-scan output
uses the component video jacks, it is not compatible with older conven-
tional analog video displays, even when they have component inputs,
unless you change the Scan Rate setting in the Video Setup submenu.
HDCP (High-Bandwidth Digital Content Protection): HDCP is the
specification for protecting digitally encoded content from unauthorized
copying when it is transmitted from a DVD player (or other video source)
to a video display using HDMI or DVI connections. In order to take
advantage of the high-resolution output of the DVD 38 via its HDMI
output, your display must be HDCP-compliant. Virtually all displays with
HDMI inputs are HDCP-compliant, but not all DVI-equipped displays are.
If you are using the DVD 38 with an optional HDMI-to-DVI cable or
adapter, check the owner’s manual for your display to determine
whether it is HDCP-compliant.
HDMI (High-Definition Multimedia Interface): HDMI is a serial-bus
form of communication between the DVD player and the video display
or audio/video receiver. It is capable of passing digital audio and high-
definition digital video using a single cable. With HDMI, the DVD 38 is
capable of outputting high-resolution (720p or 1080i) video and 5.1-
channel Dolby Digital or DTS digital audio, with the convenience of just
a single cable connection.
Reading or Loading: This is a message that you will see when you
first press the Play Button. It refers to the fact that the player must first
examine the contents of the disc to determine its type, and then extract
the information about the material on the disc, such as languages, aspect
ratios, subtitles, number of titles and more. The slight delay while the
contents of the disc are read is normal.
JPEG Files: JPEG stands for the Joint Photographic Experts Group,
which developed a standard for compressing still images, such as
photographs. JPEG files may be created on a personal computer by
importing images from a digital camera, or scanning printed photo-
graphs. These files may be burned onto a compact disc. The DVD 38
Resume: The operation of the Stop Button on the DVD 38 works
differently from what you are used to on CD players. On a traditional CD
player, when you press the Stop button, the unit does just that – it stops
playback. On a CD player, when you press the Start button again, the
disc starts from the beginning.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY
With the DVD 38, however, you have two options when playing most
discs. Pressing the Stop Button once will stop the playback, but it actually
puts the unit in the Resume mode. This means that you can turn the
machine off and, when you press the Play Button the next time, the disc
will resume playback from the point on the disc where the Stop Button
was pressed. This is helpful if you are watching a movie and must
interrupt your viewing session but wish to pick up where you left off.
Pressing the Stop Button twice will stop the machine in a traditional
manner and, when the disc is played again, it will start from the begin-
ning. In Resume mode, the Harman Kardon screen will appear, and the
RESUME message will appear in the Information Display.
The resume function is not available for WMA files. For DVDs, CDs, MP3
files, JPEG files, and VCDs with PBC (Playback Control) only, the resume
function will be retained even after the DVD 38 has been placed in
Standby mode by pressing the Standby/On Switch, but not after the unit
has been unplugged from AC power.
Title: For a DVD, a title is defined as an entire movie or program. There
may be as many chapters within a title as the producers decide to
include. Most discs include only one title, but some may have more than
one, to give you a “Double Feature” presentation or to include other
special features. Press the Title Button to see a listing of the titles on a
disc. When a disc has only one title, pressing the Title Button may show
a list of the chapters.
WMA Files: WMA (Windows Media® Audio) is an audio compression
format that was developed by the Microsoft® Corporation for use with its
Windows Media Player and other devices. WMA files can be even smaller
in size than MP3 files, while maintaining similar quality. The DVD 38 is
capable of playing WMA files stored on a disc. Although Windows Media
Player uses other file formats, the DVD 38 is only capable of playing
WMA files that end in the “.wma” extension.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Appendix – Default settings and worksheets
Table A1 – System Setup Menu Settings
Setting
Default
English
Off
Your Setting
Display Language
Preferred Subtitle Language
Panel Time-Out
Status Bar Time-Out
Parental Control
Disc Recognition
PBC Support
Off
5 Seconds
Off
On
On
Screen Saver
1 Minute
Off
Show Angle Icon
Closed Caption
On
Table A2 – Audio Setup Menu Settings
Setting
Default
Your Setting
Preferred Audio Language
English
Digital Output
PCM Limit
Bitstream
96kHz
Maximum
Feet
Dynamic Range
Delay Unit
Bass Management
On
Table A3 – Audio Adjustments Menu (Bass Management) Settings
Speaker
Position
Default
Size
Your Speaker
Size
Default Delay
Your Delay
Distance
Default
Output Level
Your Output
Level
Distance (From Speaker
to Listening Position)
Front Left
Small
Small
Small
Small
Small
N/A
11 Feet
11 Feet
11 Feet
10 Feet
10 Feet
N/A
0dB
0dB
0dB
0dB
0dB
0dB
Center
Front Right
Surround Right
Surround Left
Subwoofer
----------------
--------------
50
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Table A4 – Video Setup Menu Settings
Setting
Default
Your Setting
Aspect Ratio
Video Output
Scan Type
4:3
S-Video
Interlaced
Video Adjustments
HDMI Settings
Off
Determined at Power-Up
Table A5 – Video Adjustments Menu Settings
All settings default to “0”, showing bar ending at midpoint of the graph, except Black Level, which defaults to Full.
Setting
Your Setting
Brightness
Edges
Black Level
51
Download from Www.Somanuals.com. All Manuals Search And Download.
®
250 Crossways Park Drive, Woodbury, New York 11797
© 2007 Harman International Industries, Incorporated. All rights reserved.
Part No. CQX1A1188Z
Download from Www.Somanuals.com. All Manuals Search And Download.
|