Dual MIG welDer
Model 97503
Set up anD OperatInG InStructIOnS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
Distributed exclusively by Harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
SaVe tHIS Manual.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
cautIOn, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
SaVe tHIS Manual
cautIOn
Keep this manual for the safety
warnings and precautions, assembly,
operating, inspection, maintenance and
cleaning procedures. Write the product’s
serial number in the back of the manual
near the assembly diagram (or month
and year of purchase if product has no
number). Keep this manual and the
receipt in a safe and dry place for future
reference.
nOtIce is used to
address practices
not related to personal injury.
Notice
cautIOn, without
cautIOn
the safety alert
symbol, is used to address
practices not related to
personal injury.
IMpOrtant SaFetY
InFOrMatIOn
In this manual, on the labeling,
and all other information
General Safety rules
warnInG! read all instructions
Failure to follow all instructions
listed below may result in
provided with this product:
this is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
electric shock, fire, and/or
serious injury. The term “power
tool” in all of the warnings listed
below refers to your line-operated
(corded) Dual MIG Welder.
follow this symbol to avoid
possible injury or death.
SaVe tHeSe InStructIOnS
1. work area safety
DanGer indicates
DanGer
a. Keep work area clean and well
lit. Cluttered or dark areas invite
accidents.
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
b. Do not operate power tools in
explosive atmospheres, such as in
the presence of flammable liquids,
gases or dust. Power tools create
sparks which may ignite the dust or
fumes.
warnInG
indicates a
warnInG
hazardous situation which, if
not avoided, could result in
death or serious injury.
c. keep children and bystanders
away while operating a power
tool. Distractions can cause you
to lose control.
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. electrical safety
before plugging in. Carrying power
tools with your finger on the switch
or plugging in power tools that have
the switch on invites accidents.
a. Avoid body contact with grounded
surfaces such as pipes, radiators,
ranges and refrigerators. There is
an increased risk of electric shock if
your body is grounded.
d. Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a
rotating part of the power tool may
result in personal injury.
b. Do not expose power tools to rain
or wet conditions. Water entering a
power tool will increase the risk of
electric shock.
e. Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
c. Do not abuse the cord. Never use
the cord for pulling or unplugging the
power tool. Keep cord away from
heat, oil, sharp edges or moving
parts. Damaged or entangled cords
increase the risk of electric shock.
4. power tool use and care
a. Do not force the power tool. Use
the correct power tool for your
d. When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of
a cord suitable for outdoor use
reduces the risk of electric shock.
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
b. Do not use the power tool if the
switch does not turn it on and
off. Any power tool that cannot
be controlled with the switch is
dangerous and must be repaired.
3. personal safety
a. Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
not use a power tool while you are
tired or under the influence of drugs,
alcohol or medication. A moment
of inattention while operating power
tools may result in serious personal
injury.
c. Disconnect the plug from the
power source before making
any adjustments, changing
accessories, or storing power
tools. Such preventive safety
measures reduce the risk
of starting the power tool
accidentally.
b. use safety equipment. always
wear eye protection. Safety
equipment such as arc shaded,
impact safety full face shield,
dust mask or respirator, heavy-
duty work gloves, non-skid safety
shoes, or hearing protection used
for appropriate conditions will
reduce personal injuries.
d. Store idle power tools out of
the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool. Power
tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
c. Avoid accidental starting. Ensure
the switch is in the off-position
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
other condition that may affect the
power tool’s operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
3. Avoid eye and body damage. Arc
rays and infrared radiation can
injure eyes and burn skin. Wear
ANSI approved eye and body
protection. Do not allow viewing by
visitors without proper eye and body
protection. Use a Face Shield with
arc shaded filter plate.
f. Use the power tool, accessories and
tool bits etc., in accordance with
these instructions and in the manner
intended for the particular type of
power tool, taking into account the
working conditions and the work to
be performed. Use of the power tool
for operations different from those
intended could result in a hazardous
situation.
4. Move flammable and explosive
material at least 35 feet from the
welding arc to prevent welding sparks
or molten metal from starting a fire.
Keep a type ABC fire extinguisher
within easy reach. Thoroughly clean
the object being welded of any paint,
grease, or other foreign material.
5. Service
a. Have your power tool serviced by
a qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power
tool is maintained.
5. Avoid unintentional starting. Prepare
to begin work before turning on the
tool.
6. Do not leave the tool unattended
when it is plugged into an electrical
outlet. Turn off the tool, and unplug
it from its electrical outlet before
leaving.
Specific Safety Rules
1. Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or missing,
contact Harbor Freight Tools for a
replacement.
7. Use clamps (not included) or other
practical ways to secure and support
the work piece to a stable platform.
Holding the work by hand or against
your body is unstable and may lead
to loss of control.
2. Avoid electrical shock. Do not permit
electrically live parts, cables, or
electrodes to contact skin, clothing,
or gloves. Wear ANSI-approved
protective clothing. This unit draws
enough current to cause serious
injury or death. Before turning the
welder on, check the electrode
holder to be sure that there are no
protruding screw heads, and that
all insulation is secure. Do not weld
unless you are insulated from ground
and the work piece.
8. This product is not a toy. Keep it out
of reach of children.
9. Industrial applications must follow
OSHA guidelines.
10. People with pacemakers should
consult their physician(s) before
use. Electromagnetic fields in close
proximity to heart pacemaker could
cause pacemaker interference or
pacemaker failure. In addition,
people with pacemakers should:
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
• Avoid operating alone.
• Always use proper procedures to
• Do not use with power switch locked
on.
• Properly maintain and inspect to
avoid electrical shock.
• Any power cord must be properly
grounded. Ground Fault Circuit
Interrupter (GFCI) should also be
implemented – it prevents sustained
electrical shock.
move cylinders.
13.
Prevent eye injury and
burns. Wearing and using
ANSI-approved personal
safety clothing and safety
devices reduce the risk for
injury.
• Wear ANSI-approved safety eye
goggles underneath welding eye
protection featuring at least a
Number 10 shade lens rating.
11. WARNING: This product, when used
for welding, plasma cutting, soldering,
or similar applications, produces
chemicals known to the State of
California to cause cancer and birth
defects (or other reproductive harm).
(California Health & Safety Code §
25249.5, et seq.)
• Leather leggings, fire resistant
shoes or boots should be worn
when using this product. Do not
wear pants with cuffs, shirts with
open pockets, or any clothing that
can catch and hold molten metal or
sparks.
• Keep clothing free of grease,
oil, solvents, or any flammable
substances. Wear dry, insulating
gloves and protective clothing.
12.
Cylinders can explode
when damaged:
• Never weld on a pressurized or a
closed cylinder.
• Wear an approved head covering
to protect the head and neck. Use
aprons, cape, sleeves, shoulder
covers, and bibs designed and
approved for welding and cutting
procedures.
• Never lay a welding torch on a
cylinder.
• Never allow a welding electrode to
touch the cylinder.
• Keep cylinders away from any
electrical circuits, including welding
circuits.
• When welding/cutting overhead
or in confined spaces, wear flame
resistant ear plugs or ear muffs to
keep sparks out of ears.
• Keep protective cap in place over
the valve except when the cylinder
is in use.
14.
Prevent accidental fires.
Remove any combustible
material from the work
area.
• Use only correct gas shielding
equipment designed specifically
for the type of welding you will do.
Maintain this equipment properly.
• When possible, move the work to a
location well away from combustible
materials. If relocation is not
• Protect gas cylinders from heat,
being struck, physical damage,
slag, flames, sparks, and arcs.
possible, protect the combustibles
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
with a cover made of fire resistant
material.
gases, vapors, liquids, and dust.
Provide adequate ventilation in
work areas to prevent accumulation
of flammable gases, vapors, and
dust. Do not apply heat to a
• Remove or make safe all
combustible materials for a radius
of 35 feet (10 meters) around the
work area. Use a fire resistant
material to cover or block all open
doorways, windows, cracks, and
other openings.
container that has held an unknown
substance or a combustible
material whose contents, when
heated, can produce flammable or
explosive vapors. Clean and purge
containers before applying heat.
Vent closed containers, including
castings, before preheating,
• Enclose the work area with portable
fire resistant screens. Protect
combustible walls, ceilings, floors,
etc., from sparks and heat with fire
resistant covers.
welding, or cutting.
15. Do not touch live electrical parts.
Wear dry, insulating gloves. Do not
touch electrode or conductor tong
with bare hand. Do not wear wet or
damaged gloves.
• If working on a metal wall,
ceiling, etc., prevent ignition of
combustibles on the other side
by moving the combustibles to
a safe location. If relocation of
combustibles is not possible,
designate someone to serve as
a fire watch, equipped with a fire
extinguisher, during the cutting
process and for at least one half
hour after the cutting is completed.
16. Protect yourself from electric shock.
Do not use outdoors. Insulate
yourself from the work piece and
ground. Use nonflammable, dry
insulating material if possible, or
use dry rubber mats, dry wood or
plywood, or other dry insulating
material big enough to cover your
full area of contact with the work or
ground.
• Do not weld or cut materials
having a combustible coating or
combustible internal structure,
as in walls or ceilings, without an
approved method for eliminating the
hazard.
17. Ensure that the unit is placed on a
stable location before use. If this unit
falls while plugged in, severe injury,
electric shock, or fire may result.
• Do not dispose of hot slag in
containers holding combustible
materials. Keep a fire extinguisher
nearby and know how to use it.
18. Ground this product. This Welder
requires the attachment and use of a
UL-listed, 240 volt grounded, 3-prong,
electrical Power Cord Plug (not
• After spot welding, make a
thorough examination for evidence
of fire. Be aware that easily-
visible smoke or flame may not
be present for some time after
the fire has started. Do not weld
or cut in atmospheres containing
dangerously reactive or flammable
included). Only a qualified electrician
should install the Power Cord Plug.
Never remove the grounding prong
or modify the Power Cord Plug in any
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
way. Do not use adapter plugs with
this product.
warnInG
19. Avoid overexposure to fumes and
gases. Always keep your head out
of the fumes. Do not breathe the
fumes. Use enough ventilation or
exhaust, or both, to keep fumes and
gases from your breathing zone and
general area.
InHalatIOn HazarD:
welding and plasma cutting produce
tOxIc FuMeS.
Exposure to welding or cutting
• Where ventilation is questionable,
have a qualified technician take
an air sampling to determine the
need for corrective measures. Use
mechanical ventilation to improve
air quality. If engineering controls
are not feasible, use an approved
respirator.
exhaust fumes can increase the risk
of developing certain cancers, such as
cancer of the larynx and lung cancer.
Also, some diseases that may be linked
to exposure to welding or plasma cutting
exhaust fumes are:
• Early onset of Parkinson’s Disease
• Heart disease
• Damage to the reproductive organs
• Inflammation of the small intestine or
• Ulcers
• Follow OSHA guidelines for
Permissible Exposure Limits (PEL’s)
for various fumes and gases.
stomach
• Respiratory diseases such as
emphysema, bronchitis, or pneumonia
• Kidney damage
• Follow the American Conference of
Governmental Industrial Hygienists
recommendations for Threshold
Limit Values (TLV’s) for fumes and
gases.
Use natural or forced air ventilation and
wear a respirator approved by NIOSH to
protect against the fumes produced to
reduce the risk of developing the above
illnesses.
• Have a recognized specialist in
Industrial Hygiene or Environmental
Services check the operation
and air quality and make
20. The warnings, precautions,
and instructions discussed in
this instruction manual cannot
cover all possible conditions and
situations that may occur. It must
be understood by the operator that
common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
recommendations for the specific
welding or cutting situation.
SaVe tHeSe
InStructIOnS.
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
SpecIFIcatIOnS
InItIal Set up
InStructIOnS
Welding Current
30 ~ 120 amps
20% at 105 amps;
40% at 75 amps;
90% at 50 amps;
100% at 30 amps
read the entIre IMpOrtant
SaFetY InFOrMatIOn section
at the beginning of this manual
including all text under
subheadings therein before set
up or use of this product.
Duty Cycle
230 VAC, 21 amps
(Peak) at 60 Hz
Input Power
Open Circuit Voltage
(max)
36 VDC
tO preVent
SerIOuS InjurY
FrOM accIDental
Automatic shutdown
and restart after cool
down
warnInG
Thermal Overload
Protection with Light
OperatIOn:
0.023 to 0.030 inch
steel and stainless
steel; 0.030 to 0.035
inch flux core and
aluminum
turn the power Switch of the
tool to its “OFF” position and
unplug the tool from its
electrical outlet before
assembling or making any
adjustments to the tool.
Wire Size
22 gauge to 3/16”
Steel
Welding Capacity
Wire Spool Size
Weight
2 lb. Spool
62.2 lbs.
note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
unpackInG
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown on the cover of this manual as soon
as possible.
assembly
1. Slide the Axle (29) through the holes
at the rear of the unit.
2. Secure both Wheels (28) to the Axle
with the Locking Rings (42).
list of contents
3. Lift up the Side Panel B (1) to
expose the wire spool and Wire
Feed Mechanism (10). Pull back on
the Feed Tensioner (CC) to free the
Feed Tension Arm (DD) and lift it up.
Remove Wire Feed Wheel Cover
(AA) screws, pull out the cover, and
pull out the Wire Feed Wheel (BB).
See photo page 10.
Description
Dual MIG Welder
Qty
1
Wheel
2
Axle
1
0.030” (0.8mm) Welding Tip
0.040 (1.0mm) Welding Tip
2 Pounds (0.030”) Flux Core Wire
Hand Held Shaded Face Shield
Brush Hammer
1
1
1
1
4. Note the two parallel grooves (one
is wider) on the circumference of the
Wire Feed Wheel (BB). On the sides
1
Welder Tip Close End Wrench
24” Strap For Gas Bottle
1
2
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
of the wheel, reference markings
0.6 or 0.8 are stamped. They
8. Twist off and pull to remove the
Nozzle and unscrew the Contact tip
of the Welder.
corresponding with wire sizes: 0.6 =
0.023”, and 0.8 = 0.030” and 0.035”.
The groove facing to the inside of the
Wire Feed Mechanism (10) should
correspond with the size of wire used.
Align the axle key with the slot in the
Wire Feed Wheel and slide on the
Wire Feed Spool (BB). Replace Wire
Feed Wheel Cover (AA), the two
screws and tighten. See photo on
this page.
(DD)
(EE)
(FF)
(CC)
(BB)
(AA)
5. Lay the Welding Torch Cable (16) in
a straight line, perpendicular to the
welder unit, as much as possible.
This will prevent the wire from
puncturing the Welding Torch Cable
(16) when exiting the Wire Feed
Housing Throat (FF). See photo on
this page.
9.
Guide the tip through the feed tube
until it protrudes the Wire Feed
Wheel opening. Direct and feed at
least an inch of wire into the Wire
Feed Housing Throat (FF).
6. Remove the wing nut and the spool
axle nut from the Wire Spool Axle
(10). Make sure that the coil spring
is inserted onto the Spool Axle, and
place a spool with wire over the axle,
noting that the wire winding must
be in a counterclockwise direction.
Replace the Spool Axle Nut (10),
the wing nut, and tighten. Verify free
rotation of the spool over the axle.
10. Close Wire Feed Mechanism (10)
over the wire, and adjust Feed
Tension Knob (D) until there is a
slight resistance on the wire.
11. Remove the nozzle and contact tip of
the Welder.
the following
steps require
DanGer
applying power to the welder.
Do not touch anything with
the torch Handle or welding
wire or an arc will be ignited.
Do not touch the internal
components of the unit while
it is powered.
loading and adjusting the wire tension.
7. cautIOn: Hold onto the end of the
Welding Wire and keep tension on it
during the following steps. If this is
not done the Welding Wire will spring
backward and tangle. The end of the
wire should be straight and have no
burrs.
12. Plug the Power Cord into a grounded
230 volt electrical outlet and turn the
Welder ON.
13. Point the Torch Handle away from all
objects. Squeeze the Trigger Switch
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
on the Torch Handle until the Welding 20. Close the Side Panel B (1).
Wire feeds into the Torch Handle
about 2 inches. If necessary, move
the Torch Handle slightly in a circular
motion to help feed the Welding Wire
properly out of the Head Tube.
Connections
14. If the Welding Wire does not feed
and the Spool is stationary, turn the
Welder off and unplug it. Tighten
the Tension Adjusting Knob on the
Wire Feed Assembly, and rewind the
Welding Wire slightly before retrying.
15. Feed the Welding Wire against scrap
wood that is 2 to 3 inches away. If
Installing a gas cylinder
the Wire stops instead of bending,
turn the Welder OFF and unplug it.
Tighten the Tension Adjusting Knob
more.
21. Do not use an Argon/Mixed pressure
regulator/flow meter with CO2
shielding gas. To use CO2 shielding
gas, you must install a CO2 gas
pressure regulator/flow meter (neither
one included).
16. Turn the Welder OFF, unplug it, and
discharge the electrode to ground.
Insert the contact tip onto the Welding
Wire and screw it firmly in place.
22. Thread the provided straps through
the slots on the back of the welder.
With assistance, set the cylinder onto
the shelf at the back of the welder.
Replace the Nozzle and cut off any
excess Welding Wire over 1/2 inch.
17. Check that +/– cables to connection
Knobs (34) are correct. See photo
this page.
23. Secure the cylinder in place with both
of the straps.
18. When using Non-flux wire and
Protective gas, connect Ground cable
with clamp to the “-” terminal and the
Internal Power cable to “+” terminal.
Strap down the Argon / CO2 gas
cylinder and connect the hose to the
rear of the MIG Welder.
24. Remove the protective cap from the
cylinder. Stand to the side of the
cylinder valve, and open the valve
slightly to blow dust and dirt from the
valve. Close the valve.
25. Make sure the Flow Adjust on the
Pressure Regulator/Flow Meter
is turned off. Screw the Pressure
Regulator/Flow Meter (not included)
firmly onto the cylinder valve.
19. When using Flux-core wire (DO NOT
USE Protective gas), connect Ground
cable with clamp to “+” terminal,
and the internal Power cable to “-”
terminal.
26. Attach the Gas Line to the Pressure
Regulator/Flow Meter from the Gas
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Inlet located on the Back Panel of the
Welder.
the power cord to possible damage.
The power cord must reach the work
area with enough extra length to
allow free movement while working.
27. Adjust the flow rate of the gas by
turning the Flow Adjust. The typical
flow rate is 10-30 CFH (cubic feet
per hour). Check the Welding Wire
manufacturer’s recommended flow
rate.
3. Secure loose work pieces using
a vise or clamps (not included) to
prevent movement while working.
The work pieces should be firmly
held together and in position while
welding. The distance (if any)
between the two work pieces must
be controlled properly to allow the
weld to hold both sides securely while
allowing the weld to penetrate fully
into the joint.
28. Installation of a line-in, where
necessary, and connecting a
twist-lock plug to the power cord
must be performed by a licensed
electrician.
OperatInG InStructIOnS
4. There must not be hazardous
objects, such as utility lines or foreign
objects, nearby that will present a
hazard while working.
read the entIre IMpOrtant
SaFetY InFOrMatIOn section
at the beginning of this manual
including all text under
subheadings therein before set
up or use of this product.
5. A barrier, such as a welding curtain
or welding shroud should be put up
to protect others in the work area and
limit the spray of sparks.
tool Set up
General Operating Instructions
tO preVent
SerIOuS InjurY
FrOM accIDental
OperatIOn:
turn the switch to its off
position before performing
any inspection, maintenance,
or cleaning procedures.
warnInG
protective gear
must be worn
DanGer
when using the MIG welder;
anSI-approved, arc shaded,
eye protection, a full face
shield, heavy-duty work
gloves, a welding apron,
respirator, and heavy-duty
work clothes without pockets
should be worn when using
this product. Do not look at
the ignited arc without eye
protection. light from the arc
can cause permanent damage
to the eyes. light from the
arc can burn the skin. Do not
breathe arc fumes.
work piece and work area Set up
1. Designate a work area that is clean
and well-lit. The work area must not
allow access by children or pets to
prevent injury and distraction.
2. Route the power cord along a safe
route to reach the work area without
creating a tripping hazard or exposing
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Always read and follow wire
manufacturer’s recommended
polarity. If using non-flux core wire,
secure the Argon/CO2 gas hose to
the rear of the MIG Welder. (If using
flux core wire, protective gas is not
required.)
2. Attach the Ground Cable with Clamp
(14) as close as possible to the metal
object to be welded.
The duty cycle defines the number of
minutes, within a 10 minute period, during
which a given Welder can safely produce
a particular welding current. For example,
this Welder, with a 20% duty cycle at 105
Amps (setting Max 2), must be allowed
to rest for at least 8 minutes after two
minutes of continuous weld at 105 Amps.
3. Set the desired current (30~120
amps) for the type of metal being
welded with the Temperature
Controller. Thin metals use low
current and heavy metals use high
current.
• Failure to carefully observe duty
cycle limitations can stress a
Welder’s power generation system,
contributing to premature Welder
failure.
Set Switch amps Duty Volts
cycle
Min. / 1
Min. / 2
Max. / 1
Max. / 2
30
100%
90%
40%
20%
15.2
16.5
17.7
19.2
50
75
105
• This Welder is equipped with an
internal thermal protection system
to help prevent damage to the
unit. When the unit overheats; it
automatically shuts down, then
returns to service when it cools
down.
4. Make sure the power switch is off,
then plug the MIG Welder Power
Cord into a dedicated, 230 VAC, 20
amp line with delayed action type
circuit breaker or fuses.
5. While holding the Welding Torch
handle, with the electrode wire clear
of grounded objects, turn the Power
Switch ON.
• Once the unit returns to service,
follow a more conservative duty
cycle routine to help prevent excess
wear to the Welder.
6. Momentarily press the Welding Torch
trigger switch to test the wire feed
speed. Adjust the speed by turning
the Wire Speed Knob.
7. Hold the Arc Shaded Face Shield
over your eyes.
8. Press (and hold) the Torch Trigger
Switch and stroke the area to be
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
welded with the electrode wire
to ignite the arc. Never tap the
electrode wire into the welding
surface to ignite the arc.
14. When the weld is complete, lift the
Welding Torch handle away from any
grounded object, remove your Face
Shield, and turn the power Switch
OFF.
9. The Welding Wire should extend no
more than 1/2” past the Nozzle of the 15. Unplug the power cord from the
Welding Torch.
electrical outlet.
10. The Welding Wire should be directed
straight into the joint. This gives an
angle of 90 degrees (straight up and
down) for groove (end to end) welds,
and an angle of 45 degrees for fillet
(T-shaped) welds.
16. Read the included weld diagnosis
pamphlet for tips and suggestions
concerning welding and proper
usage.
17. To prevent accidents, turn off the
tool and disconnect its power supply
after use. Clean, then store the
tool indoors out of children’s and
unauthorized people’s reach.
11. The end of the Welding Torch should
be tilted so that the Welding Wire is
angled anywhere in between straight
on and 15 degrees in the direction of
the weld. The amount of tilt is called
the “drag angle”.
12. The wire feeds automatically, and
can be changed using the Wire
Speed Knob.
13. If too much current is drawn from
the MIG Welder, the overload
protection will activate, the red
overload indicator will light, and the
Arc Welder will shut down. If this
happens, turn the power Switch OFF
and wait about 3 ~ 5 minutes before
restarting.
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
compressed air, blow out all dust and
debris from the interior.
MaIntenance anD
SerVIcInG
4.
warnInG! If the supply cord of
this power tool is damaged, it must
be replaced only by a qualified
service technician.
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
nozzle care
tO preVent
SerIOuS InjurY
FrOM accIDental
OperatIOn:
warnInG
1. Turn the Nozzle counterclockwise
while pulling to remove.
turn the power Switch of the
tool to its “OFF” position and
unplug the tool from its
electrical outlet before
performing any inspection,
maintenance, or cleaning
procedures.
2. Scrub the interior of the Nozzle clean
with a wire brush.
3. Examine the end of the Nozzle. The
end should be flat and even. If the
end is uneven, chipped, melted,
cracked, or otherwise damaged, the
Nozzle will adversely effect the weld
and should be replaced.
tO preVent SerIOuS
InjurY FrOM tOOl
FaIlure:
Do not use damaged
equipment. If abnormal noise
or vibration occurs, have the
problem corrected before
further use.
4. Replace the Nozzle after inspecting
and cleaning the Contact Tip
contact tip care
1. Make sure the entire Welding Torch is
completely cool before proceeding.
cleaning, Maintenance, and
lubrication
2. Remove the Nozzle, as explained
above, and the Contact Tip.
3. Scrub the exterior of the Contact Tip
clean with a wire brush. Check that
the Contact Tip is the proper type for
the wire size used.
1. beFOre eacH uSe, inspect the
general condition of the tool. Check
for loose screws, misalignment or
binding of moving parts, cracked or
broken parts, damaged electrical
wiring, and any other condition that
may affect its safe operation.
4. Examine the hole at the end of
the Contact Tip for the following
problems:
2. aFter uSe, clean external surfaces
• Shape: The hole should be an even
circle, and should not be oblong or
have any bulges in it.
of the tool with clean cloth.
3. perIODIcallY, open the Access
• Size: The Contact Tip will decrease
Panel (12) from the unit and, using
in efficiency as the center hole
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
enlarges. A Contact Tip that
measures 150% or more the
original size* should be replaced.
(*.045” or more for .030” Tips; .035”
or more for .023 Tips.)
8. Attach the Fitting at the end of the
Liner to the Push-lock Coupler on the
Switch Body.
9. Slide the Liner Sleeve back onto the
end of the liner. Reinstall the Cable
Clamp and Screws. Trim off the Liner
that extends past the Clamp.
5. If any problems are noted with a
Contact Tip, have it replaced.
6. When inspection and maintenance is 10. Make sure that all torch parts lay
completed, reinstall the Contact Tip
and Nozzle.
back into place properly including
the Protective Sleeve, Head Tube,
and Trigger. See Assembly Diagram.
While all parts are properly in place,
carefully put the Upper Housing back
onto the Lower Housing and slide
back to secure. Slide the Locking
Collar back onto the Housings and
twist to secure.
replacing the welding torch
liner
1. Switch welder off, disconnect power,
and discharge electrode to ground
before proceeding.
2. Secure welding wire to the spool, cut
it near the spool, and remove it from
the torch and cable.
11. Check the Torch carefully for proper
operation.
12. Route the Wire as instructed in the
Loading and Adjusting the Wire
Tension Section.
3. Gently twist and slide the Locking
Collar off the torch and onto the
Protective Sleeve. Slide the Upper
Housing forward and off the Lower
Housing.
4. Remove the four Screws that hold the
Cable Clamp in place. Set aside the
Cable Clamp, Screws, and the Liner
Sleeve underneath the cable clamp.
5. Lay torch cable out straight to allow
the cable to twist within the sleeve.
6. Press in on the Push-lock Coupler
and remove the Liner from the gun
end.
7. Install a new Liner and Fitting from
the gun end with the end without a
Fitting first.
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
welding arc not stable.
trOubleSHOOtInG
Possible Causes and Solutions:
DanGer
Important! Be
• Wire not feeding properly:
See first Troubleshooting section
above.
CERTAIN to shut off the Welder,
disconnect it from power, and
discharge the torch to ground before
adjusting, cleaning, or repairing the
unit.
• Incorrect contact tip size:
Replace with the proper tip for the
wire size used.
• Incorrect wire feed speed:
Adjust wire feed speed to achieve a
more stable arc.
wire feed motor runs but wire does not
feed properly.
Possible Causes and Solutions:
• Loose torch cable or ground cable:
Check to ensure that all
connections are tight.
• Insufficient wire feed pressure:
Increase wire feed pressure.
• Incorrect wire feed roll size:
Replace with the proper size.
• Damaged torch or loose connection
within torch:
• Damaged torch, cable, or liner
assembly:
Have a qualified technician inspect
and repair/replace as necessary.
Have a qualified technician
inspect these parts and replace as
necessary.
welder does not function when
switched on
Possible Causes and Solutions:
wire creates a bird’s nest During
operation.
• Tripped thermal protection device:
Shut the welder’s switch to off
and allow it to cool for at least 20
minutes.
Reduce duration or frequency of
welding periods to help reduce wear
on the welder.
Possible Causes and Solutions:
• Excess wire feed pressure:
Adjust wire feed pressure.
• Incorrect contact tip size:
Replace with the proper tip for the
wire size used.
Refer to Duty Cycle section.
• Faulty or improperly connected
Switch Body:
Have a technician check and
secure/replace Switch Body.
• Gun end not inserted into drive
housing properly:
Loosen gun securing bolt and push
gun end into housing just enough
so that it does not touch wire feed
mechanism.
• Internal fuse blown:
Have a qualified technician check/
replace.
• Damaged liner:
Have a qualified technician inspect
and repair/replace as necessary.
weak arc strength
Possible Cause and Solution:
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
• Incorrect line voltage:
pleaSe reaD tHe FOllOwInG
careFullY
Check the line voltage and, if
insufficient, have a licensed
electrician remedy the situation.
THE MANUFACTURER AND/OR DISTRIBUTOR
HASPROVIDEDTHEPARTSLISTANDASSEMBLy
DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOLONLy. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANy REPRESENTATION
OR WARRANTy OF ANy KIND TO THE BUyER
THAT HE OR SHE IS qUALIFIED TO MAKE ANy
REPAIRS TO THE PRODUCT, OR THAT HE OR
SHE IS qUALIFIED TO REPLACE ANy PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR ExPRESSLy STATES
THATALLREPAIRSANDPARTSREPLACEMENTS
SHOULD BE UNDERTAKEN By CERTIFIED AND
LICENSED TECHNICIANS, AND NOT By THE
BUyER. THE BUyER ASSUMES ALL RISK AND
LIABILITyARISINGOUTOFHISORHERREPAIRS
TOTHEORIGINALPRODUCTORREPLACEMENT
PARTS THERETO, OR ARISING OUT OF HIS OR
HER INSTALLATION OF REPLACEMENT PARTS
THERETO.
wire Feeds, but arc does not ignite
Possible Causes and Solutions:
• Improper ground connection:
Make certain that the work piece is
contacted properly by the Ground
Clamp and that the work piece is
properly cleaned near the ground
clamp and the welding location.
• Improperly sized or excessively
worn Contact Tip:
Verify that Contact Tip is the proper
size for the welding wire used.
Check that the hole in the tip is
not deformed, enlarged, or dirty. If
needed, replace Contact Tip with
proper size and type.
wire Feeds, but Shielding gas does not
Flow
Possible Causes and Solutions:
• Empty Gas Cylinder:
Check gas cylinder.
• Nozzle Plugged:
Clean nozzle. If damaged, replace.
• Regulator or cylinder valve closed:
Make sure both valves are adjusted
properly.
• Gas line blocked:
Check external hose, and hose
within Torch cable.
• Gas solenoid broken or not
connected properly:
Have a qualified technician check/
replace.
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
partS lISt anD aSSeMblY DIaGraM
Description
Part
1
Part
22
Description
Filter Reactor
Side Panel B
2
Hinge
23
Main Transformer
Transformer Carriage
Bottom Plate
Plastic Foot
3
Handle Socket
Straight Handle
Fan
24
4
25
5
26
6
Back Panel
27
Axle Bracket
Wheel, Plastic
Axle
7
Rectifier Rack
Clap Panel
28
8
29
Wire Spool Axle
Wire Feed Mechanism
Wire Feed Wheel
Side Panel A
Power Cord
9
30 Temperature Controller
10
11
12
13
14
15
16
17
18
19
20
21
31
32
33
34
35
36
37
38
39
40
41
42
Control Circuit Board Bracket
Control Circuit Board
Potentiometer
Knob
Ground Cable With Clamp
Welding Torch / Cable
Cover
Nut, Copper, M6
Washer, Spring, 6
Washer, Copper, Plain,6
Washer, Insulating, 1
Screw, Copper, M6X35
Washer, Insulating, 2
Brace
Wire Speed Knob
Switch
Overload Light
Cable Nib
Rings, 8
Front Panel
10
7
6
8
9
11
12
5
33
32
31
34
13
14
4
40
35
41
36
39
38
37
3
2
1
21
20
19
18
17
16
15
22
23
30
24
25
29
28
27
26
42
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
lIMIteD 1 Year / 90 DaY warrantY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that for a period of
ninety days from date of purchase that the torch, liner, wire feed mechanism (if applicable),
welding clamps, electrode holders, cables and accessories packed with the welder are
free of defects in materials and workmanship. this limited 90 Day/1 Year warranty
shall not apply to consumable parts such as tips, welding wire, and gas nozzles.
Harbor Freight Tools also warrants to the original purchaser, for a period of one year from
date of purchase, that the transformer and rectifier are free from defects in materials and
workmanship (90 days if used by a professional contractor or if used as rental equipment).
This warranty does not apply to damage due directly or indirectly to misuse, abuse,
negligence or accidents, repairs or alterations outside our facilities, normal wear and tear,
or to lack of maintenance. We shall in no event be liable for death, injuries to persons or
property, or for incidental, contingent, special or consequential damages arising from the
use of our product. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation of exclusion may not apply to you. THIS
WARRANTy IS ExPRESSLy IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITy AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the complaint
must accompany the merchandise. If our inspection verifies the defect, we will either
repair or replace the product at our election or we may elect to refund the purchase price
if we cannot readily and quickly provide you with a replacement. We will return repaired
products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specific legal rights and you may also have other rights which
vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
record product’s Serial number Here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 97503
For technical questions, please call 1-800-444-3353.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
|