ORBITAL JIGSAW
WITH LASER
Model 94560
ASSEMBLY AND OPERATING INSTRUCTIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
©
®
Copyright 2006 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SAFETY
4.
Grounded tools must be plugged into an outlet properly installed and
grounded in accordance with all codes and ordinances. Never remove the
grounding prong or modify the plug in any way. Do not use any adapter
plugs. Check with a qualified electrician if you are in doubt as to whether
the outlet is properly grounded. If the tools should electrically malfunction or
break down, grounding provides a low resistance path to carry electricity away
from the user.
5.
6.
Double insulated tools are equipped with a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install a polarized outlet. Do not
change the plug in any way. Double insulation eliminates the need for the
three wire grounded power cord and grounded power supply system.
Avoid body contact with grounded surfaces such as pipes, radiators, rang-
es, and refrigerators. There is an increased risk of electric shock if your body is
grounded.
7.
8.
Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
Do not abuse the Power Cord. Never use the Power Cord to carry the tools
or pull the Plug from an outlet. Keep the Power Cord away from heat, oil,
sharp edges, or moving parts. Replace damaged Power Cords immediately.
Damaged Power Cords increase the risk of electric shock.
9.
When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. These extension cords are rated for outdoor use, and
reduce the risk of electric shock.
PERSONAL SAFETY
10.
11.
Stay alert. Watch what you are doing, and use common sense when operat-
ing a power tool. Do not use a power tool while tired or under the influence
of drugs, alcohol, or medication. A moment of inattention while operating
power tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
SKU 94560
For technical questions, please call 1-800-444-3353
PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
12.
13.
14.
15.
Avoid accidental starting. Be sure the Power Switch is off before plugging
in. Carrying power tools with your finger on the Power Switch, or plugging in
power tools with the Power Switch on, invites accidents.
Remove adjusting keys or wrenches before turning the power tool on. A
wrench or a key that is left attached to a rotating part of the power tool may result
in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enables better control of the power tool in unexpected
situations.
Use safety equipment. Always wear eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
TOOL USE AND CARE
16.
Use clamps (not included) or other practical ways to secure and support
the workpiece to a stable platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
17.
18.
Do not force the tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
Do not use the power tool if the Power Switch does not turn it on or off.
Any tool that cannot be controlled with the Power Switch is dangerous and must
be replaced.
19.
Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
20.
21.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with a sharp cutting edge are less likely to bind and are easier
to control. Do not use a damaged tool. Tag damaged tools “Do not use” until
repaired.
22.
Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect the tool’s operation. If damaged, have
the tool serviced before using. Many accidents are caused by poorly main-
tained tools.
SKU 94560
For technical questions, please call 1-800-444-3353
PAGE 4
Download from Www.Somanuals.com. All Manuals Search And Download.
23.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.
SERVICE
24.
25.
Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow in-
structions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
SPECIFIC SAFETY RULES
1.
Hold the tool by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring or its own cord. Contact
with a “live” wire will make exposed metal parts of the tool “live” and shock the
operator.
2.
3.
Maintain labels and nameplates on the Jigsaw. These carry important infor-
mation. If unreadable or missing, contact Harbor Freight Tools for a replacement.
Always wear safety impact eye goggles and heavy work gloves when using
the Jigsaw. Using personal safety devices reduce the risk for injury. Safety im-
pact eye goggles and heavy work gloves are available from Harbor Freight Tools.
4.
Maintain a safe working environment. Keep the work area well lit. Make sure
there is adequate surrounding workspace. Always keep the work area free of ob-
structions, grease, oil, trash, and other debris. Do not use a power tool in areas
near flammable chemicals, dusts, and vapors. Do not use this product in a damp
or wet location.
5.
6.
Avoid unintentional starting. Make sure you are prepared to begin work before
turning on the Jigsaw.
Do not force the Jigsaw. This tool will do the work better and safer at the
speed and capacity for which it was designed. Do not force the Saw Blade into
the workpiece being cut.
7.
8.
WARNING! Keep hands and fingers away from cutting area and Saw Blade.
Never leave the Jigsaw unattended when it is plugged into an electrical out-
let. Turn off the tool, and unplug it from its electrical outlet before leaving.
SKU 94560
For technical questions, please call 1-800-444-3353
PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
Before using the Jigsaw, check to make sure the Saw Blade is properly
mounted on the Blade Chuck. Make sure the Saw Blade is sharp, and is not
cracked or bent.
10.
11.
Industrial applications must follow OSHA guidelines.
When cutting a large workpiece, make sure its entire length is properly sup-
ported. If necessary, use a roller stand (not included).
12.
13.
14.
15.
16.
17.
18.
When using the Jigsaw, always maintain a firm grip on the tool with both
hands.
Do not use the Jigsaw if it has been dropped, damaged, left outdoors, or
immersed in liquid.
To avoid electrical shock, do not handle the Jigsaw or its Power Cord Plug
with wet hands.
To avoid injury, always wear heavy duty work gloves when changing Saw
Blades.
Make sure the workpiece is free from nails and any other foreign objects
which can damage the Saw Blade.
Always check to make sure there are no electrical wires or cables in the
cutting path of the Jigsaw.
Allow the Saw Blade to run up to full speed before feeding it into a
workpiece. When turning off the Jigsaw, allow the Saw Blade to stop on its own.
Do not press against the Saw Blade to stop it.
19.
20.
21.
Turn off the Jigsaw and allow the Saw Blade to completely stop if the
Saw Blade is to be backed out of an uncompleted cut.
Never attempt to remove material stuck in the moving parts of the Jigsaw
while it is plugged in and running.
Always ensure the Laser Beam is aimed at a sturdy workpiece without a
reflective surface. Bright, shiny, reflective workpieces are not suitable for Laser
use as the surface could reflect the beam back at the operator.
22.
Always unplug the Jigsaw from its electrical outlet before performing any
inspection, maintenance, or cleaning procedures.
SKU 94560
For technical questions, please call 1-800-444-3353
PAGE 6
Download from Www.Somanuals.com. All Manuals Search And Download.
MISCELLANEOUS PRECAUTIONS
1.
WARNING! Some dust created by power sanding, sawing, grinding, drilling,
and other construction activities, contain chemicals known (to the State of Califor-
nia) to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are: lead from lead-based paints, crystalline silica from bricks
and cement or other masonry products, arsenic and chromium from chemically
treated lumber. Your risk from these exposures varies, depending on how often
you do this type of work. To reduce your exposure to these chemicals: work in
a well ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)
2.
3.
WARNING! People with pacemakers should consult their physician(s) before
using this product. Operation of electrical equipment in close proximity to a heart
pacemaker could cause interference or failure of the pacemaker.
WARNING! The warnings and cautions discussed in this manual cannot
cover all possible conditions and situations that may occur. It must be under-
stood by the operator that common sense and caution are factors which cannot
be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS
GROUNDING
WARNING!
Improperly connecting the grounding wire can result in the risk of electric
shock. Check with a qualified electrician if you are in doubt as to whether the
outlet is properly grounded. Do not modify the power cord plug provided with
the tool. Never remove the grounding prong from the plug. Do not use the
tool if the power cord or plug is damaged. If damaged, have it repaired by
a service facility before use. If the plug will not fit the outlet, have a proper
outlet installed by a qualified electrician.
GROUNDED TOOLS:TOOLS WITH THREE PRONG PLUGS
1.
Tools marked with “Grounding Required” have a three wire cord and three prong
grounding plug. The plug must be connected to a properly grounded outlet. If
the tool should electrically malfunction or break down, grounding provides a low
resistance path to carry electricity away from the user, reducing the risk of elec-
tric shock. (See Figure A, next page.)
SKU 94560
For technical questions, please call 1-800-444-3353
PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
3.
The grounding prong in the plug is connected through the green wire inside the
cord to the grounding system in the tool. The green wire in the cord must be the
only wire connected to the tool’s grounding system and must never be attached
to an electrically “live” terminal. (See Figure A.)
Your tool must be plugged into an appropriate outlet, properly installed and
grounded in accordance with all codes and ordinances. The plug and outlet
should look like those in the following illustration. (See Figure A.)
THIS PRODUCT
DOES NOT
USE A
3-PRONG PLUG
120 VOLT,
GROUNDED,
ELECTRICAL OUTLET
FIGURE A
DOUBLE INSULATED TOOLS:TOOLS WITH TWO PRONG PLUGS
4.
5.
Tools marked “Double Insulated” do not require grounding. They have a special
double insulation system which satisfies OSHA requirements and complies with
the applicable standards of Underwriters Laboratories, Inc., the Canadian
Standard Association, and the National Electrical Code. (See Figure B.)
Double insulated tools may be used in either of the 120 volt outlets shown in the
following illustration. (See Figure B.)
THIS PRODUCT
USES A
2-PRONG PLUG
120 VOLT,
GROUNDED,
ELECTRICAL OUTLETS
FIGURE B
SKU 94560
For technical questions, please call 1-800-444-3353
PAGE 8
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTENSION CORDS
1.
2.
Grounded tools require a three wire extension cord. Double Insulated tools
can use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a
serious drop in voltage, resulting in loss of power and possible tool damage.
(See Figure C.)
3.
4.
5.
The smaller the gauge number of the wire, the greater the capacity of the cord.
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(See Figure C.)
When using more than one extension cord to make up the total length, make
sure each cord contains at least the minimum wire size required.
(See Figure C.)
If you are using one extension cord for more than one tool, add the nameplate
amperes and use the sum to determine the required minimum cord size.
(See Figure C.)
6.
7.
If you are using an extension cord outdoors, make sure it is marked with the suf-
fix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified elec-
trician before using it.
8.
Protect your extension cords from sharp objects, excessive heat, and damp or
wet areas.
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*
(120 OR 240 VOLT)
NAMEPLATE
AMPERES
EXTENSION CORD LENGTH
(At Full Load)
25 Feet
50 Feet
75 Feet 100 Feet 150 Feet
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
-
* Based on limiting the line voltage drop to five volts at
150% of the rated amperes.
FIGURE C
SKU 94560
For technical questions, please call 1-800-444-3353
PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOLOGY
FIGURE D
UNPACKING
When unpacking, check to make sure all the parts shown on the Parts List on page 16
are included. If any parts are missing or broken, please call Harbor Freight Tools at the
number shown on the cover of this manual as soon as possible.
PRODUCT FEATURES
1.
Speed Adjuster (28): The Speed Adjuster is a 6-position speed dial switch
located on the top/front of the handle. By rotating the Speed Adjuster from 1 to
6, the Saw Blade speed can be set from 800 to 3,000 strokes per minute.
(See Figure E next page, and Figure F page 13.)
2.
3.
Power Switch (29): The Power Switch is operated manually simply by squeez-
ing the Switch to turn on the Jigsaw and releasing pressure on the Switch to turn
off the Jigsaw. (See Figure E.)
Switch Lock (30): The Jigsaw is equipped with a Power Switch lock mechanism.
To operate the tool for extended periods of time squeeze and hold the Power
Switch (29), then depress the Switch Lock. To unlock the Power Switch, squeeze
and release the Power Switch once. (See Figure E.)
4.
5.
Cutting Mode Lever (39): The Cutting Mode Lever can be adjusted to select the
straight cutting mode or orbital cutting mode. The Cutting Mode Lever has 4-po-
sition settings. The setting marked “0” is for straight cutting, and the settings
marked “I”, “II”, and “III” are for orbital cutting. (See Figure E.)
Laser Switch (35): The Jigsaw is equipped with a Laser Guide (36) that is de-
signed to aid alignment of the Saw Blade with the cutting line on the workpiece.
To operate, push the Laser Switch to its ON or OFF positions. (See Figure E.)
SKU 94560
For technical questions, please call 1-800-444-3353
PAGE 10
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
7.
Dust Chute (54): For a clearer cut line the Jigsaw can be attached to a vacuum
system (not included) that will suck dust away from the cutting line. The Jigsaw
comes equipped with a Dust Chute that allows a standard household vacuum
system to be attached to the tool. (See Figure E.)
Base Plate Cover (50): The Jigsaw is equipped with an adjustable Base Plate
Cover which allows for bevel cutting from 0 to 45 degrees left or right. To
adjust the Base Plate Cover, pull out and temporarily remove the Dust Chute
(54). Use the accessory Hex Wrench (66) to loosen the Hex Screw (53) located
on the underside of the Base Plate Cover. Adjust the Base Plate Cover to the
desired angle. Then retighten the Hex Screw and replace the Dust Chute.
(See Figure E.)
8.
9.
Edge Guide (70): The Edge Guide allows for extended straight cuts from
0 to 5-1/2” wide. To attach the Edge Guide to the Jigsaw, loosen the Edge
Guide Lock Knob. Slide the Edge Guide into the Base Plate (49) assembly.
Adjust the Edge Guide to the width of cut desired. Then, retighten the Guide
Lock Knob. (See Figure E.)
Blade Holder (59): The Blade Holder allows for convenient storage of additional
Saw Blades. Slide the Blade Holder backward off the Jigsaw to store and re-
trieve Saw Blades. (See Figure E.)
28
29
35
30
59
39
70
54
50
FIGURE E
SKU 94560
For technical questions, please call 1-800-444-3353
PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
To Install A Saw Blade:
1.
CAUTION! Always make sure the Power Switch (29) of the Jigsaw is in its
“OFF” position and the tool is unplugged from its electrical outlet prior to adding
any accessories or making adjustments to the tool.
2.
3.
Refer to the Chart below to select the proper Saw Blade (68, 69) for the material
being cut. (See Figure F.)
Open the Plastic Blade Guard (58). Press the clamp button on the Blade Chuck
(24). Insert the Saw Blade (68, 69) as far as it will go, making sure the teeth of
the Saw Blade face to the front of the tool. Then release the clamp button on the
Blade Chuck, and close the Plastic Blade Guard. (See Figure G.)
BLADE SELECTION AND SUITABLE SPEED
Material
Soft Wood
Hardwood
Plastic
Aluminum
Steel
Tile
Glass
Leather
Rubber
Teeth Per Inch
Speed Setting
6
6
12
12
24
24
32
6
5
4 ~ 6
3 ~ 6
2 ~ 4
1 ~ 3
1 ~ 3
4 ~ 6
4 ~ 6
(Knife Edge)
(Knife Edge)
FIGURE F
SAW BLADE
(68, 69)
PLASTIC BLADE GUARD
(58)
BLADE CHUCK
(24)
FIGURE G
SKU 94560
For technical questions, please call 1-800-444-3353
PAGE 12
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATING INSTRUCTIONS
1.
CAUTION! Always use safety equipment. Wear ANSI approved safety impact
eye goggles and heavy duty work gloves when operating the Jigsaw. Also, a dust
mask and hearing protection must be used for appropriate conditions.
2.
3.
4.
IMPORTANT: Always secure the workpiece in place, using a vise or clamps (not
included).
Make sure the Power Switch (29) is in its “OFF” position and the Power Cord/
Plug (65) is unplugged from the electrical outlet. (See Figure E.)
If necessary, make adjustments to the Speed Adjuster (28) and Cutting Mode
Lever (39). Also if necessary, adjust the Base Plate Cover (50) for the desired
bevel of cut. (See Figures E and F.)
5.
6.
Once all adjustments are made, plug the Power Cord/Plug (65) into the nearest
120 volt, grounded, electrical outlet.
Position the Saw Blade (68, 69) of the Jigsaw about 1/2” from the beginning cut
line on the workpiece. Do not allow the Saw Blade to come in contact with the
workpiece.
7.
8.
Turn the Laser Switch (35) to its “ON” position, and align the laser beam with the
cut line on the workpiece. (See Figure E.)
Squeeze the Power Switch (29) to turn on the Jigsaw. If operating the Jigsaw for
an extended period of time, you may wish to depress the Switch Lock (30) to
lock the Power Switch in its “ON” position. (See Figure E.)
9.
Allow the Saw Blade (68, 69) to stroke at full speed before slowly feeding it into
the workpiece.
10.
11.
Make sure to hold the Jigsaw firmly with both hands to avoid kickback. Then,
finish making the cut.
When finished, release the Power Switch (29) to stop the Jigsaw. Wait until the
Saw Blade (68, 69) stops completely. Turn the Laser Switch (35) to its “OFF”
position. Then, remove the Jigsaw from the workpiece. (See Figure E.)
12.
Make sure to store the Jigsaw in a clean, dry, safe location out of reach of chil-
dren and other unauthorized people.
SKU 94560
For technical questions, please call 1-800-444-3353
PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem
Possible Solution
Jigsaw will not run, or runs with insufficient power. 1. Make sure to firmly squeeze the Power Switch. (See Figure E.)
2. Make sure the Power Cord/Plug is plugged into a working 120 volt,
grounded, electrical outlet.
3. Allow the tool to completely cool in the event of overheating. Then, resume
cutting.
4. Have a qualified service technician check the Carbon Brushes for
excessive wear and/or debris build-up.
Quality of cut is poor.
1. Check to make sure the Saw Blade is sharp and undamaged.
2. Make sure the Saw Blade is properly installed in the tool. (See Figure G.)
3. Make sure to use the proper type of Saw blade for the material being cut.
(See Figure F.)
4. Make sure to use the proper cutting speed for the material being cut. (See
Figure F.)
5. Do not force the Saw Blade. Gradually feed the Saw Blade into the
workpiece.
Laser Guide will not illuminate.
1. Make sure the Laser Switch is in its “ON” position. (See Figure E.)
2. Turn the Laser Switch to its “OFF” position. Then, check to make sure the
Laser Guide is free of excessive dirt and debris.
3. Have a qualified service technician check the tool for internal damage.
The Power Switch does not turn off the tool.
Immediately unplug the tool from its electrical outlet, and have a qualified
service technician check the tool for damage and defects.
INSPECTION, MAINTENANCE, AND CLEANING
1.
2.
WARNING! Make sure the Power Switch (29) of the Jigsaw is in its “OFF”
position and the tool is unplugged from its electrical outlet before performing any
inspection, maintenance, or cleaning procedures.
Before each use, inspect the general condition of the Jigsaw. Check for loose
screws, misalignment or binding of moving parts, cracked or broken parts, dam-
aged electrical wiring, and any other condition that may affect its safe operation.
If abnormal noise or vibration occurs, have the problem corrected before further
use. Do not use damaged equipment.
3.
4.
Before each use, inspect the Saw Blade (68, 69). Using a dull Saw Blade will
cause excessive wear on the Motor of the Jigsaw and will not produce a satisfac-
tory cut. Replace with a new Saw Blade when needed. (See Figure G.)
To clean the exterior parts of the Jigsaw, use only a clean cloth and mild
detergent to clean the body of the Saw. Do not immerse any electrical part of
the tool in any liquids.
5.
CAUTION! All maintenance, service, or repairs not mentioned in this
manual must only be performed by a qualified service technician.
SKU 94560
For technical questions, please call 1-800-444-3353
PAGE 14
Download from Www.Somanuals.com. All Manuals Search And Download.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES
ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESS-
LY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISKS AND LIABILITY ARIS-
ING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR
ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
PARTS LIST
Part
1
2
3
4
5
6
7
8
Description
Upper Enclosure
Lower Enclosure
Bearing (626-2Z/C3)
Stator
Qty.
1
1
1
1
1
2
2
2
1
1
2
1
1
1
1
2
1
1
1
1
1
1
1
1
Part
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Description
Friction Plate
Spring
Spring Holder
Speed Adjuster
Power Switch
Switch Lock
Spring
Qty.
1
4
1
1
1
1
1
1
2
1
1
1
2
4
1
1
1
1
1
1
1
1
4
1
Part
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
Description
Base Plate
Base Plate Cover
Screw (M3 x 8)
Base Retainer
Hex Screw (GB70-85)
Dust Chute
Upper Aluminum Guard
Lower Aluminum Guard
Front Aluminum Guard
Plastic Blade Guard
Blade Holder
Nameplate
Nameplate
Internal Wire
Junction Port
Cable Guard
Power Cord/Plug
Hex Wrench
Screw (ST4.2 x 19-F-H)
Wood Cutting Blade
(Not Shown)
Metal Cutting Blade
(Not Shown)
Qty.
1
1
12
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Rotor
Epoxy Block
Carbon Brush (D308)
Brush Holder
Bearing (609-2RZ/C3)
Gear Case Sub-Assy.
Pin
Pin
Block
Washer
Pendulum Plate
Balance Plate
Washer
Gear Sub-Assy.
Washer
Anchor
Screw
PCB
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Laser Switch
Laser Guide
Washer
Screw (ST3.5 x 8-F-H)
Cutting Mode Lever
Lever Pivot
Spring (B)
Cutting Mode Lever Axis
Pin
1
11
Safety Ring
Nut Block
68
2
Bearing (K081215)
Rolling Ring
Upper Bearing
Blade Chuck
Guiding Wheel Axis
Guiding Wheel Holder
Pin
69
70
1
1
Edge Guide w/Lock Knob
Steel Wire Support
LIMITeD 90 DAy
wArrAnTy
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this
product is free from defects in materials and workmanship for the period of ninety days from the date of purchase. This warranty does not apply to damage due
directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of maintenance.We shall in no event be liable for
death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THiS WarranTy iS expreSSly in
lieu oF all oTHer WarranTieS, expreSS or implied, inCluding THe WarranTieS oF merCHanTabiliTy and FiTneSS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. proof of purchase date and an explanation of the
complaint must accompany the merchandise. if our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund
the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no
defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 94560
For technical questions, please call 1-800-444-3353
PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DIAGRAM
SKU 94560
For technical questions, please call 1-800-444-3353
PAGE 16
Download from Www.Somanuals.com. All Manuals Search And Download.
|